Home

DN9231 - Dante Security

1. ee es DC 12V cable is required for thie device Make sure the polarity is correct before you connect the power cable Incorrect connection may cause malfunction or damage to the IP device Video connection Connect a LAN cable to the LAN connector of the device to retrieve the IP devices Connect a display device such as monitor to the Video output connector on the back panel of the device using 75 ohm video coaxial cables with a BNC connector c The device supports two way mono audio for H 264 encoder only Since the output power for the audio is low an amplifier speaker is needed for a clearer sound Ain Aout O O O O O O O O Lam u Mic Amp Speaker Audio input range 0 01 3 3 Min Max 01A 03 Dante Security Inc 10 DN9231 User s Manual Sensor Input D D There are two sensor interface types Voltage Type and Relay Type The interface type can be controlled by the software Before connecting sensors check driving voltage and output signal type of the sensor Be aware that the connection is different according to sensor type before connecting cables Internal Internal Output of Output of DI 1 SENSE E sensor 1 Output of DI 2 OR Output of Sensor 2 Malt 5VDC 24VDC Relay Type Voltage Type Input voltage range 0 VDC minimum to 24 VDC maximum Inp
2. 01A 03 Dante Security Inc 9j i Ta m 135 n B 125 5 LE S e Unit mm 58 DN9231 User s Manual REVISION HISTORY COMMENTS 05 28 2010 Created Preliminary version for DP sample 11 24 2010 Initial version Modified explanation about Serial over IP 01A 02 02 09 2011 Changed the incorrect reference for the priority channel configuration 01A 03 04 14 2011 Corrected the subscriber per event publisher table 01A 03 Dante Security Inc 59
3. 01A 03 Dante Security Inc 14 DN9231 User s Manual 4 Basic Setup 4 1 Network Setup The default IP address of your IP device is 192 168 XXX XXX You can find the available IP address from the MAC address of your device Please make sure the device and your PC are on the same network segment before the installation If the network segment of your PC is different from the device change your PC s IP setting as below IP address 192 168 xxx xxx Subnet mask 255 255 0 0 Internet Protocol TCP IP Properties Internet Protocol TCP IP Properties oM MM General General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings You can get IP settings assigned automatically if pour network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically C Obtain an IP address automatically Use the following IP address IP address 10 10 110 179 IP address 192 168 110 179 Use the following IP address Subnet mask 29h AD ee a ee Subnet mask 255 255 IT 0 Default gateway Default gateway Use the following DNS server addresses Use the following DNS server addresses Preferred DNS server l m j Preferred DNS server Alternate DNS server Alternat
4. Reset When you set DI as a publisher DO Email Multicast TCP and HTTP server can be the subscriber of DI triggering Subscriber DO Check the DO box you want to trigger and click Apply button For example if you check off the DO 1 of DI 2 gt when DI 1 is detected DO 2 will be activated Subscriber Email If you check Post notification message and click Apply button the server will send the notification message by e mail to the client when DI detection is occurred System Option SMTP and email account must be configured to activate this function Attaching a snapshot on an email is not available Subscriber Multicast 01A 03 Dante Security Inc 37 DN9231 User s Manual If you check Post notification message and click Apply button the server will send the notification message via Multicast server when DI detection is occurred Multicast server must be configured to activate this function by clicking the link button Multicast Subscriber TCP If you check Post notification message and click Apply button the server will send the notification message via TCP server when DI detection is occurred TCP server must be configured to activate this function by clicking the link button TCP Subscriber HTTP If you check Post notification message and click Apply button the server will send the notification message via HTTP server when DI detection is occurred HTTP server must be configure
5. DN9231 H 264 MPEG4 MJPEG Video Video Audio Data Decoder Installation and Operations Manual Model Number DN9231 4 Description H 264 MPEG4 MJPEG Decoder Dual Configurable Video Streams with duplex Audio Data Alarms DN9231 User s Manual Table of Contents L PACKAGE CONTENTS 4i exa eoa ose eURu a REN ue en E dus oA TA EE Ju DRE 5 2 INTRODUCOTION ann A 6 2 1 Malm FALUN CS c E 6 2 2 Hardware OVObVI BW soc nent nouer d a Ea uer a abs 7 2 2 T Front Papel etitecesstut miss adudobi ait aub d ost d mS KoD Mad A Ubq EM nS OA inrUit done 7 2 2 2H RAP PANNES RS use usado endende nee dan 8 3 InstallatiOln oe estes ceo o E eet e rie lens sets Mala Re ec s M MUN M Ed 9 3 1 Video Output Configuration Switch ennemis 9 SAU Glen EIE T E UU UT 10 SESTERCE 14 4 Basic Setup iin eire eere e Laid aeo GE annee rotin etaient POENI UIS 15 d NeBvorK SEP aco eem tuens Tei EN aere Picasa dci ita Su bet Gen one 15 4 2 System Configuration on Web Page ccccccccssscsssecesecesecescessseueteueneuenesetesensencseneseness 16 4 3 Vid o DISDIaV uci had odis o aae d toa sel e codo eL DLL eM ile UD HC Ld 17 R OSC me M EE 18 qo FactorvDeFatill e oct teeters sic ditssce deatur credi te podre cian c caede ti dens ln aceon 18 5 HOW to Use OSD Mens eo eo nea keel Ur to Ori ue EREMO Ver BU a OH UR UR 19 5 1 Menu COMMU aU OM sca aad dede uo iube E V ORI eoe todos cot Op uU Mon iacu ae viva eis aus 19 B22 DISDIAY MOG f
6. Audio in Audio out DI DO UART 1 UART 2 USB PoE SD slot Day amp Night Rack information 6 9 2 licenses On the Licenses page the information for the third party software license that has been used on the development of the device is displayed 01A 03 Dante Security Inc 54 DN9231 User s Manual APPENDIX A SPECIFICATIONS Summary TBD Resolution 25 30 fps D1 PAL NTSC Megapixel is not supported Video Output se Configuration Switch PP Input output 1 1 channel Compression FPS Compression Format G 711 Function Digital Input output 2 2 channel TCP IP UDP IP HTTP RTSP RTCP RTP UDP RTP TCP Protocol SNTP mDNS UPnP SMTP SOCK IGMP DHCP DDNS SSL v2 v3 IEEE 802 1X SSH TBD USB 2 0 Support for USB mouse SD Memory N A 1036 x EH x 410 m Electrical Characteristics Linein 1 43Vp p Min 1 35Vp p max 1 49 Vp p 39 KO 01A 03 Dante Security Inc 55 DN9231 User s Manual With mouse connected Environment Condition Operating Temperature O 9C 60 9C 32 9F 140 9F Operating Humidity Up to 8596 RH Mechanical Condition 103 W x 38 H x 141 0 mm Weight Approx 385g 01A 03 Dante Security Inc 56 DN9231 User s Manual APPENDIX BJ POWER OVER ETHERNET The Power over Ethernet PoE is designed to extract power from a conventional twisted pair Category 5 Ethernet cable conforming to the IEEE 802 3af Power over Et
7. C TI net 20 D2 POAC I prp P THE 20 5 2 2 SIngleVIe Wesen SR M ach adeft cca EU LM s ALES E 20 5 2 9 IP WOW oe ca ne p LE EM ed E D E estos 20 ons Nolo OCS fet han tant de D da Seance gees tea tadt 21 BA QUICK MENU gr a NN Dm id tn Reda re 21 54 1 Changing connection MO sio eode nn ob eo eae 21 5 4 2 Checking device and channel information 22 5 43 REDONE CEVC Esrin a Pe pode dtt tnmen depu ter E AME E EE 22 5 How to Use Web Pace cd eec v pete tic ee 23 Gal Recommended PC SpecilicallOTIisesn olestie orales ate seo cans nr Rd nn te 23 6 2 Basic COMMU SUA TION ost cond Dan a oc ida du tt ace actui datas da tnodo ian ie ee 24 o7 lyser manage MENE osisdetiatiso stes eam adu E e nn ete I sense 24 6 2 3 Setting date and time Of d is cos ec ded xa am i ar eade oe itum d be ieee 28 b 3 Encoder SetDtiBsoscossdba dta ble YO p Db d et cde Mean de eme bob prc DUE 30 01A 03 Dante Security Inc 2 DN9231 User s Manual 6 4 Decoder SEINE iecit a adio ate eee uo ai ea tei e qu uuu EU LEE EI 32 SPART PP 32 0420S Dp P 33 5 4 3 JA UIO onis acess at tes Gents cane top Qu Meno ce shaun teu o dt en tate oet gt 34 D o EVENE ConlbeHldliOlic escecctor ne en en des scena quarte te ee 34 6 5 1 How to configure each event Servers ohne ee EE S E RYD ONE Fas 35 6 5 2 Assigning event rule to event publishers 37 6 62 SYSTEM OP TON sesioan tea nsc en te tt rem ti
8. Selecting display mode To specify how to display the video image on the default screen select the desired mode on the View Mode option In the Spot View mode only one video is displayed on the screen In the Quad View mode the evenly split four windows appear on the screen View Mode Spot Quad Spot mode setting Selecting the Spot mode will display the configuration options on the spot mode as below Select the channel you want to display in a single view If you want to enable PIP then select the channel for PIP and defined its resolution and position Afterward check the Enable PIP box and click the Apply button on the bottom of the page The Switch PIP button is activated only when the PIP mode is enabled To switch the image that is displayed in the sub window with the full screen image click the Switch PIP button Spot Configuration Spot channel e CH 1 CH CH 3 CHA PIP Configuration Enable PIP PIP channel 9 CHF CH 2 CH FS CHA PIP Resolution Predefined QCIF PIP Position Predefined right bottom Quad mode setting Displaying all of the 4 channels in a view with high bitrate may be resulted in low quality images If you want to keep the best quality for a specific channel while having too much DSP interference give a priority on the channel by selecting its channel number on the following option This option will be enabled only when you select the Quad mode 01A 03 Dante Security Inc 32 DN9231 User s Manual P
9. capturing analogue audio generated at the camera installed site After the configuration of Listen you can listen to the sound with a speaker connected to the mm device To listen to the captured sound click the speaker M icon on the screen If you uncheck the box of Enable capture and compression audio it will disable the server to capture the sound The audio out stream from the decoder to an encoder is only available when you select TYPEO H 264 encoder for Encoder Type TYPE1 or RTSP is not Note supported The products are equipped with the event server program internally and it enables you to configure the event publishers and subscribers For instance DI DO Network loss and health of network server can publish the event message when an event is generated How to move to each subscriber setting page Go to Setup Event Configuration DI then the Publisher DI page appears as below Click each subscriber name such as DO and you can find that they are linked to the related setting pages Refer to the figures of below for more specific information 01A 03 Dante Security Inc 34 DN9231 Publisher DI v DO 1 C HTTP Server 3 beet EEEEEELITE LICE NM Agen M ca nn nn mmmmmmmnmmumumuHE User s Manual 6 5 1 How to configure each event server 1 Email server You can use Email server to get the event notification from the device and send them to the client applica
10. different one move your mouse point to the right top of the full image view and then select the desired view by referring to the icons described on 5 2 2 Single View 1 Switch full window with sub window 2 Switch the channel of sub window 01A 03 Dante Security Inc 20 DN9231 User s Manual If you click the Enable Audio button from the shortcut icons you can hear the output sound When the audio output is enabled the icon will be changed as the following figure m KE D Audio disabled Audio enabled To hear the output sound make sure that the audio input output cable is properly connected with a microphone and speaker To learn how to connect audio cables refer to 3 2 Cabling 5 4 Quick Menu If you right click on a view the Quick Menu appears as below This menu helps you to change connection mode reboot the device or check its version RS YT LL WAR ture mide sire et 1 L Cha nges the view with the P instant mode Check boxes for selecting Change selected monde a connection mode mi met v Dctail Displays the channel P Proset 42 PA lvunmmi 1 P Preset 44 l ex I meh M Preset 46 iln 7 P Frosct 48 Lveraen Reboot Close Closes the quick menu jj Save configuarions Saves the channel configurations Available only in Preset Mode Displays the version of 1 device Reboots device 9 4 1 Changing connection mode The decoder supports two differen
11. even odd 9 none Stop 1 bit 2 bit Flow Control none The UART setup is supported with two different pages UART1 and UART2 For the RS485 port use the UART1 setup page For the RS232C port use the UART2 setup page VART tyne Internal PTZ Used when you connect a PTZ camera to an encoder RS485 is for UART1 and RS232 is for UART2 AUX Used when you connect an auxiliary device that requires serial communication to an encoder RS485 is for UART1 and RS232 is for UART2 SerialOverlP Used to enable the communication for the devices connected to the serial ports of an encoder 01A 03 Dante Security Inc 50 DN9231 User s Manual Why distinguish between PTZ and AUX When the PTZ type is selected the required PTZ protocol and the control daemon are run and assigned to the serial communication internally External When 3 party program is added to the server side of the encoder and this add on program needs to control the attached serial devices you should select the external option So if you do not use any serial control program you can ignore this option This section is enabled only when you select SerialOverlP for the UART type Select the desired communication mode UDP TCP Client or TCP Server And type the IP address of client and port number on the text box of SerialOverlP section If you select the TCP Client or TCP Server mode you can set the time to automatically end the connection when there is no data com
12. is between 0 and 65 the LED will operate as you configured at Location tab 3 Turn on the LED of Vsignal Select one of the options between When video signal loss is detected and When video signal is normal Then the selected LED will operate when the selected condition is satisfied 4 Turn on the LED of Heartbeat Select one of the options between When heartbeat status is watchdog and When heartbeat status is normal Then the selected LED will operate when the selected condition is satisfied 6 6 7 DDNS Dynamic DNS To change the Dynamic DNS setting go to Setup gt System Options gt DDNS and follow the procedures below Configuration Enable DDNS DDNS Protocol Type Type DynDNS v DDNS Setting Domain name Update time 600 second s 1 864000 10days Email address MAC address Logon Information User name Password CETTIIIL 1 Check the Enable DDNS box 2 Select the protocol type you want DynDNS and Custom07 are installed on the device only Note 3 Type the domain name you want to use for the product 4 Type the update time The factory default is 600 seconds and it enables the product notify the DDNS of the current domain name 5 Type the user name and password of your DDNS account Note that 8 asterisks cannot be used for the password 6 Click the Apply button 01A 03 Dante Security Inc 46 DN9231 User s Manual To enable the remote management of IP devic
13. odi odas 39 6 6 1 TCP IP DHCP Static IP DNS setup setup 39 emm NIP Sarver SOUPE rm 40 ost diui SOLU RERUM 41 6 6 42 MDNS Multicast DNS SSD vitm Vea M ner qu EI Tex e eee Esa EY PM dU 42 fepe Mg Tigre 43 GO Ge LED omm 45 5 07 DDNS Dyna Mie DNS uariis apad trente de GER RR ERT bass 46 GOS SNMP eec 47 6 7 IO CONFIGURATION Mt x H 48 OI DIDO CON LORS TENUE NER a E E 48 6 7 2 UART setine Tor serial GOVICE uode reor beu T prre oe ERE tete ere te 50 6 2 MAINTENANCE epp V 6 53 G S 1 Firmware bdateport Seu coche cece eel eree eratis E E ate NM aU dE 53 6 5 22 GELLING SVSteIm LOB oce ut it Ma rea E pa opd iL 53 GS ABOUT SR toon ede osos daba re eines du io in et notion er nee 54 0 91 VOIR SSSR RSS IM IM c MEE HL s 54 09 25 II EM 54 APPENDIX A SPECIFICATIONS st 0d peus bep eco up EP LOIN oo 55 UMMM al Versa es dd Da mda adque DS cotes a be UC dA S des 55 Electrical Character Sti B susocencsoxs ok as cese ttu ee Io etus Rossi edu toc odes o 55 Environment Condition e Mente 56 Mechanical CONGIION ERO E C TTE DO TEILE 56 APPENDIX B POWER OVER ETHERNET eee eee nee enne ene senes sesso tenue 57 POE corhpatibIll D sss bestie oreet beate LR Si be
14. page Digital Sensor DI and Alarm DO DI Resource type RELAY VOLTAGE max 5V DIDOstatus 1 2 DI OPEN OPEN DO OFF OFF DO Control DO1 mcam DO2 OFF ON Friendly name DI 1 DI1 NAME DI 2 DI2 NAME DO 1 DO1 NAME DO2 DO2 NAME DI Trigger type DI 1 Normal Open Normal Close DI 2 Normal Open Normal Close DI Re arm period DI 1 0 second 0 999 0 trigger for every detection DI 2 0 second 0 999 0 trigger for every detection DO Hold period DO 1 0 second 0 99999 0 infinite DO2 0 second 0 99999 0 infinite You can choose the DI resource type RELAY or VOLTAGE The maximum is 5V DI amp DO Status It reflects the current states of actual DI and DO 2 of DI and DO are supported on the device To understand DI DO status options refer to the following scenario Scenario When it s assumed that DI 1 and DO 1 are coupled by event system The DI 1 trigger type is Normal Open Suddenly DI 1 is triggered by any kind of event Expected Response The status of DO 1 will be changed from OFF to ON if the default setting is OFF The status of DI 1 will be changed from OPEN to CLOSE 01A 03 Dante Security Inc 48 DN9231 User s Manual If you want to test DO operation manually on the webpage click the soft buttons of OFF and ON Then you can see that how DO works These commands also affects the DO status because the DO status shows the current status of DO You can type any frien
15. the resources from the cache you should manually empty your cache If the content expiration mode is not enabled the cache 01A 03 Dante Security Inc 26 DN9231 User s Manual control may perform depending on the client PC environment specifically your Internet Explorer option setting 01A 03 Dante Security Inc 27 DN9231 User s Manual 6 2 3 Setting date and time of device Time setting is very significant for all parts of the product server because it affects the log of streaming and burnt in text of video To set the time go to Setup Basic Configuration Date amp Time Every time you change the setting the web server program of the product will be restarted internally It may take more than a minute to restart Date amp Time Setting Current Server Time 1970 01 19 16 49 06 UTC New Server Time Time Zone Universal Time Automatically adjust for daylight saving time changes Method amp Synchronize with computer time Date 2010 08 31 Time 14 14 20 Synchronize with NTP server NTP Server ntp1 usv ra Set manually Date 1970 01 19 Time 18 43 50 Time Synchronize Sync source NTP server amp Real Time Clock on system Interval Everyday 00 00 When the system gets started the system time is synchronized with NTP server But if you do not have your DNS or not available to access the internet the system time synchronizes with RTC Apply Reset Display of current server time It shows the curr
16. to your PTZ camera hardware manual for the PTZ address setting 01A 03 Dante Security Inc 51 DN9231 User s Manual Serial port setup These settings are necessary when you want your serial device to be communicated with the encoder or IP camera The default values of web page are set for the RS485 PTZ device but you can set the values according to your own device requirement 01A 03 Dante Security Inc 52 DN9231 User s Manual 6 8 MAINTENANCE 6 8 1 Firmware update nort setup Firmware Update Configuration Enable Firmware Update TCP IP listen port number of server 1111 1 65535 Firmware update is allowed only by the IPAdminTool exe which is provided in the SDK BIN TOOLS AdminTool vX X X X Refer to the PADminTool User s Manual pdf to find out how to update the firmware on your devices Before you upload the firmware with IPAdminTool exe go to Setup gt Maintenance gt Firmware Update Then select the Enable Firmware Update check box and set the port number If you remove the check from this box updating the firmware is not allowed 6 8 2 Getting system Log In order to get the system log of the product please follow the steps of below 1 Goto Setup Maintenance System Log Check the Enable System Log box 3 Type max size of file between 32KB and 200KB Then the log files will be created according to the fixed size Up to 5 files are created and the oldest file will be replaced by the latest
17. ENC is typed as a default for the name but it is adjustable as you want 6 6 5 SMTP setup To change the SMTP setting go to Setup gt System Options gt SMTP email SMTP email Setting User Information Unit Name ENC From email address event test com Server Information Mail server smtp test com hostname or ip address Mail Server port 25 1 65535 Enable encrypted connection SSL Logon Information Username tester Password IITTIIIII Test Send test mail to test Apply Reset You can set the user s mail account and server to apply this SMTP for event or any other SMTP required purpose Unit Name Type the friendly name for the product server to show on e mail and it helps you to distinguish the devices from other devices when you use multiple network video servers Input range 40 characters limit From email address Type the e mail address of a sender 01A 03 Dante Security Inc 43 DN9231 User s Manual Input range 128 characters limit Mail server In order to send the e mail message the product needs the information of user s mail server Type the Mail server with the host name or IP Address If you use the host name it requires the DNS registration in advance Check the DNS setting on System Options TCP IP tab Input range 128 characters limit Mail server port Type the mail server s port number with the range from 0 to 65535 If your email server requires encryption process of
18. Preset 1 8 a pop up window appears to configure channels of an encoder to display To configure video channels refer to the following details about setting options Preset name setup Unlike in the Instant mode setting window the Friendly name option is added in the Preset mode Since 8 different preset modes are supported defining a certain preset mode with a promptly noticeable name would be helpful for users Input the desired name on the text box of preset name for an easier recognition of the preset mode Friendly name preset name 1 st floor Selecting a channel for configuration Select the tab of the desired channel number to configure To display the channel select the Enable check box If you unselect the check box the channel will not be displayed on the screen Encoder Information Set the encoder information including the encoder type session type URL and HTTP port The encoder type includes three types as described on the table below Type TYPEO H 264 encoder TYPE1 MPEG4 encoder RTSP Connect via RTSP standard The RTSP type is generally for connecting a third party product If you want to connect the standard encoders that can be categorized by TYPEO or TYPE1 with the RTSP type make sure to check the encoder URL has been input correctly according to its session type rtsp hostname or ipaddress port session name The HTTP port number is required only for the configuration of TYPEO and TYPE1 Enc
19. SSL and TLS select the Enable encrypted connection SSL check box TLS Transport Layer Security and SSL Secure Sockets Layer algorithm can be required for the security of communication Note over networks It depends on your email server and you should check out the communication protocol of SMTP server Logon information User name Input range 128 characters limit Password Input range 32 characters limit 8 asterisks cannot be used for the password Test with current configuration You can check if the e mail account is available or not with the test button Type the e mail address and click the test button If you have seen the message below you should set the DNS first at System Option TCP IP menu Windows Internet Explorer 4 IF a hast name is used a valid DNS server must be specfied in the TCP IP network settings If you have seen the message below the entered mail account is valid Windows Internet Explorer 4 jen kim udptechnology com OK send to email 01A 03 Dante Security Inc 44 DN9231 User s Manual 6 6 6 LED Setup To change the LED setting go to Setup System Options LED LED Setting Configuration v Enable LED Location Event Publisher Operation Time Qut V Top Yellow heartbeat Blink On permanent v Bottom Green vsignal 9 Blink On permanent Option Setthe dspload limits to under 0 100 default 90 Set the temperature limits to Under Celsius 40 def
20. Server Lists NTP Server 1st ntp1 usv ro NTP Server 2nd clock isc org NTP Server 3rd ntp shoa cl NTP Server 4th time bora net Local SNTP Server Setup C I am SNTP Server It will take about 3 4 minutes until it works NTP Server Lists You can set up to 4 NTP servers as you can see at the example of above To enable the NTP servers DNS server setting should be done in advance in the menu of TCP IP page and please check out if the DNS configuration is accurate am SNTP Server 01A 03 Dante Security Inc 40 DN9231 User s Manual It is also called Squid server When you have multiple servers for the device it helps to reduce the network load because only the one with I am SNTP Server checked will get the time information from the NTP servers and other servers for the device are synchronized with this Squid server How to use 1 Enable am SNTP server of squid server and click Apply 2 Access the webpage of the device which is supposed to be the client device of the squid server Go to System Options NTP and type the IP address of squid server on the NTP Server 1s t Format example 192 168 11 4 3 Click the Test button to find out if it works fine It will take about 3 4 minutes until the squid server response Note 4 Go to Setup Basic Configuration Date amp Time and choose the Synchronize with NTP server for the method of New Server Time menu Make sure if the NTP Server displays
21. and held 3 Release the Reset button after 5 seconds 4 Wait for the system to reboot 01A 03 Dante Security Inc 18 DN9231 User s Manual 9 1 Menu Configuration On the display monitor that is connected to the device you can use several menus When you move your mouse on a view channel OSD appears as following figure For its feature refer to the descriptions below O 4 15 168 15 145 a ET RS OT Do us 4 turrem made instant mire W instant mode Change Itani 1 Dctail P Proset 42 Itari 1 P Fresct 44 Ires t D Preset 46 Itre 7 F Fresct 48 Verzion Rcboot Close IP address It displays the IP address of the connected encoder If you click on this the Device List menu appears On the Device List menu select the desired device you want to connect For more information about how to display a video of an encoder refer to 4 3 Video Display 2 Quick menu It appears when you right click on the monitor With this menu you can change the current display with a preset display that is pre defined by a user Thus it supports to check the device version or channel configuration and reboot the device Refer to 5 5 Quick Menu for more details 3 FPS It displays the frame rate of a channel 4 Shortcut Icons With the shortcut icons you can enable audio or change the display mode Refer to 5 2 Display Mode and 5 3 Audio Mode for more details 01A 03 Dante Security Inc 19 DN9231 U
22. ault 0 Min Max Celsius 40 100 default 0 65 Over Celsius 100 default 65 Turn an the LED af vsignal When videa signal lass is detected When videa signal is normal Turn on the LED of heartbeat When heartbeat status is watchdag amp When heartbeat status is normal Apply Reset You can customize the LED operation according to your system requirement Please refer to the example scenario first Scenario When the video signal loss is detected let top LED blink for every 5 seconds Setting Top Yellow Ticked Event Publisher vsignal Operation Blink Time Out 5 Option Turn on the LED of vsignal Select When video signal loss is detected 1 Select the Enable LED check box to enables the LED function 2 Select the event publisher you want to apply for the LEDs 3 Select the operation type of each LED Blink or On mode 4 Select the time out value 1 to 5 sec and permanent alarming are supported G Refer to 2 2 1 Front Panel for the location of LEDs on the device Note 01A 03 Dante Security Inc 45 DN9231 User s Manual The option page provides the configuration of DSP load temperature change and video loss 1 Set the dspload limits to E g Setting the value as 9096 While the DSP load keeps lower than 9096 the LED will operate as you configured at Location tab 2 Set the temperature limits to E g Setting the min O and max 65 While the temperature
23. ay of giving a notice En the client PCs Windows Internet Explorer ak J If DHCP server happens to fail to lease an IP address because of unexpected network problem or DHCP server error the latest static IP address will be applied instead 01A 03 Dante Security Inc 39 DN9231 User s Manual Use the static IP address If you want to use your device with the static IP enable the Use the following IP addresses and click the Apply button IP address The IP address of your device Subnet mask The address of subnet mask of your device Gateway address The gateway address of your device Broadcast address It is automatically fixed by the subnet mask and IP address of your own For example if you use B class 255 255 0 0 of mask the broadcast address will be 192 168 255 255 The test button shows if the typed IP address is occupied or not You may find the popup windows as below according to the availability of typed IP address Windows Internet Explorer Windows Internet Explorer E AN 192 168 42 25 address is currently in use 4 192 168 11 5 address is not in use Occupied IP Available IP DNS Configuration Type the IP address of DNS server you use The test button for checking the IP address availability is also supported for DNS configuration Refer to the explanation for the test button above for details 6 6 2 NTP server setup To change the NTP service setting go to Setup System Options NTP NTP Setting NTP
24. c information Power connector Connect the power adaptor for power supply DC 12V 1A adaptor is needed 01A 03 Dante Security Inc 8 DN9231 User s Manual 3 1 Video Output Configuration Switch The video output configuration switch enables to turn the video output on or off on a monitor If you set this switch to Off no image will be displayed on the monitor but a black screen To turn the video output on set this switch to NTSC or PAL according to the video standard before you connect the power cable If you want to change its output configuration after the power cable is connected put the switch to the desired position and reboot the system To learn how to reset your device refer to 4 4 Reset Video Out Configuration Switch The video output configuration must be set before you turn on the device Changing the setting after the device is turned on will not affect on the Note configuration 01A 03 Dante Security Inc 9 DN9231 User s Manual 3 2 Cabling USB Mou LAN Cable l CN DUC M er Power Cable DI RS232 E DC 12V a A 33 6 6 6 4 69 8 8 8 8 8 D oo In U 11 1j im 1j im U 11 U 11 U 11 Li 11 1j im 1j
25. cation step before a user logs in 1 Goto Setup Basic Configuration Users 2 Select Enable 3 Check the option box to allow all anonymous users for accessing the web page If you want to request to enter ID and password even for entering the web page skip to step Disable Apply Reset 4 Uncheck the option box and click the Apply button to save the changes To skip an authentication step before a user logs in to the Setup page 1 Goto Setup Basic Configuration Users 2 Select Disable 3 Click the Apply button to save the changes For an enhanced security selecting the Enable option is recommended Note 01A 03 Dante Security Inc 24 DN9231 User s Manual To add a user for the webpage 1 Goto Setup Basic Configuration Users 2 Click the Add button below the User List 3 When the pop up window appears type a user name and password Add User User name Operator Password eee Confirm password eeee Viewer 9 User group pars Administrator OK Came 4 Select the desired account level from Operator and Administrator The Viewer account is not available 5 Click the OK button to save the changes 6 Check if the user name is added to the list User List User Name User Group Add Modify Remove To change your password or user group 1 Goto Setup Basic Configuration Users 2 Onthe User List select the user name for changing
26. coded images on a monitor For its main features refer to the following summary 1 channel H 264 30fps Q CIF decompression Decompress H 264 MPEG 4 and MJPEG streams Audio compression and decompression G 711 System configuration on a webpage 01A 03 Dante Security Inc 6 DN9231 User s Manual 22 Hardware Overview 2 21 Front Panel 1CH Decoder NTSC PAL OFF System status LEDs The LEDs are located on the left side of the front panel and they indicate certain system information Status This LED lights up as orange and turns green when the decoder is powered on Data This LED lights up when the host system is turned on with a connection is made The color of LEDs is subject to change according to the firmware version Loop out BNC connector As a loop out connector connect to a device such as a monitor 3 Output setting switch This button enables to turn the video output on or off on a monitor If you set this switch to Off no image will be displayed on the monitor To turn the video output on set this button to NTSC or PAL according to the IP device s video format before you connect the power cable The video output configuration must be set before you connect the power cable Changing the setting after the device is turned on will not affect on the Note configuration 01A 03 Dante Security Inc 7 DN9231 Us
27. d to activate this function by clicking the link button HTTP If you have finished to configure the event server and required subscribers click Apply button for the application 01A 03 Dante Security Inc 38 DN9231 User s Manual 6 6 SYSTEM OPTION 6 6 1 TCP IP DHCP Static IP DNS setup setup To change the TCP IP setting go to Setup gt System Options gt TCP IP IP Address Configuration Obtain an IP address via DHCP IP address Subnet mask Gateway address Broadcast address Use the following IP address IP address 192 168 19 153 Subnet mask 255 255 0 0 Gateway address 192 168 0 1 Broadcast address DNS Configuration Primary DNS Server 0 0 0 0 IP address Secondary DNS Server 0 0 0 0 IP address Apply Reset Obtain IP address via DHCP If you want to get your IP from DHCP server automatically check this option and click the Apply button You may find the message box of below is popped up It explains that the DHCP server in your router device may cause a problem and fail to lease new IP address In that case the latest static IP address will be applied instead Click OK button to accept the notification Windows Internet Explorer The IP address of Ehe unit will be changed according to your new setting and use new IP address Eo access webpage After change of the IP address the new IP address can be notified by UPnP mONS and email Make sure they are configured in the w
28. dly name for DI and DO This setting helps you to identify which DI or DO is activated especially when you have multiple product servers on your application program DI Trigger Type You can select the trigger type between normal open NO and normal close NC Use this option to set up detection time interval for event publishers For example if you input 0 it generates events all the time whenever DI is detected But if you input 10 only 1 event will be triggered for 10 seconds even if multiple DIs are detected for this 10 seconds The DO Hold Period indicates for how long does the DO works For example if you input O a DO device keeps working until a user turns it off manually If you input 10 a DO device will work for 10 seconds and finish the operation However if you turn a DO device on manually by using the DO Control button it will be activated without being affected by the DO hold period unless you click the OFF button 01A 03 Dante Security Inc 49 DN9231 User s Manual 6 1 2 UART setting for serial device For the USRT setting go to Setup IO Configuration UART LIART1 UART2 Type Internal RS485 PTZ External R amp 485 ALX SerialOverlP Mode UDP TCP Client TCP Server IP address Port Timeout O unlimited 1 9999 seconds Status PTZ Protocol PTZ Mame pelco d_ptzs hi PTZ Address 1 Serial port Setup Baud Rate 9600 Data 5 bit 6 bit f bit 8 bit Parity
29. e 6 1 Recommended PC specification The following table describes the minimum and recommended requirement of the PC system to use a Web browser with our products VGA Nvidia ATI ATI Radeon Series Intel built in graphic Nvidia Geforce Series Memory 64 MB Memory 128 MB Win 98 ME XP Vista Windows XP SP2 or higher Diretx oo 90 X 01A 03 Dante Security Inc 23 DN9231 User s Manual 6 2 Basic Configuration 6 2 1 User management The menus allowed to access may vary depending on your user group The root user ID root PW pass is authorized to all menus on the Setup page and this default user is not removable Beside the root user you can add a user group The user group is divided into two different levels Operator and Administrator Refer to the table below for details about accessible menus of each account User Group Accessible Menu Operator Encoder Configuration Decoder Configuration Event Configuration Administrator All menus Limitation on user name A user name can contain from 1 to 14 characters with a combination of alphabet and numbers Maximum of 32 accounts are available per an account group Character range All upper or lower case letters and the number from 0 to 9 Limitation on password A password can contain from 1 to 8 characters with a combination of alphabet and numbers Character range All upper or lower case letters and the number from O to 9 To have an authenti
30. e DNS server 01A 03 Dante Security Inc 15 DN9231 User s Manual 4 2 System Configuration on Web Page You can set up the system configuration on a web page of your device Follow the directions below to use its web page for the system configuration 1 Convert a MAC address to an IP address or check the IP address on the IPAminTool The MAC address is attached on the side or bottom of the device MAC address 00 13 23 01 14 B1 IP address 192 168 20 177 the Hexadecimal number to Decimal number 2 Open a web browser and enter the IP address of the device You also can right click on the device on the IPAdminTool and select Web view 3 Enter the default user name root and password pass and click the OK button 4 When the Setup page appears click System Options on the left and then select TCP IP from the drop down menu 5 Input the data for the IP address configuration and click the Apply button on the bottom of the page To change the IP address please make sure to check and have the correct Subnet mask and Gateway ready To use DHCP select Obtain an IP address via DHCP 6 Set up the necessary system configuration on the web page Refer to Chapter 6 How to Use Web Page for details IPAdminTool automatically searches all activated network encoders and IP cameras and shows product name IP address MAC address etc To search your device and use its web page more easily use IPAdminTool that is provided with SDK at th
31. e following SDK path SDK root BIN TOOLS AdminTool 01A 03 Dante Security Inc 16 DN9231 User s Manual 4 3 Video Display To display the decoded images on the screen follow the steps below 1 Move the video output configuration switch to NTSC or PAL according to the IP device s video format If you put the switch to OFF no image will be displayed on the monitor but black screen Make sure all the cables are connected to the device properly Check if the 4 split view appears on the connected monitor Click on No device on the upper left corner of each split view to open the dialog box which list available devices On the Device list window select the device to connect and click the Select button Then the Select stream window appears E IFINI AET Device list for ch 1 1 4 51 devices Refresh Device name IP Address No device Camera1 192 158 17 8 Camera 2 Camera 3 Camera 4 Camera 6 Camera 7 Camera 8 Encoder 1 Encoder 2 Encoder 3 Encoder 4 Encoder 5 192 168 43 220 192 168 110 63 192 168 15 12 192 168 48 84 192 168 20 245 192 168 20 132 192 168 31 246 192 168 18 52 192 168 24 149 192 168 21 164 192 168 13 164 Encoder 6 192 168 15 15 lEncoder 7 192 158 25 241 mmm mecum 6 Onthe Select stream window Select the channel and stream to decode and click the Select button 11N0 device TT select stream Device Camera 1 192 158 15 12 Channel a
32. e from a client PC to the encoder in a specified time Input the desired time on the timeout text box The Status box indicates the connection status in the TCP Client or TCP Server mode Refer to the following table and check how the message appears according to a connection status Status Message for TCP Client Message for TCP Server Not Connected Connecting Disconnected Connected Connected Connected 0 The Timeout and Status option are available only in the TCP Client and TCP Server mode Note You can check the communication status from the client PC by using a related freeware If you run the program and connect to a device via its IP address and port number you can see that the data transferred from the port has been received at UART1 You must distinguish this option from the general concept of SerialOverlP which allows controlling the devices connected to a serial port of the IP device by using HTTP API commands For the information of this commands refer to NVD HTTP Note API Manual pdf PTZ Protocol PTZ Name You need to set the UART type as RS485 PTZ before selecting the PTZ protocol If you click the drop down box of PTZ name the available protocols are listed Choose the required protocol to communicate with your camera PTZ Address Type the PTZ address as you have set on your PTZ camera You may find the dip switch at the bottom of the PTZ camera which enables the cameras to have their own address Refer
33. ent server time with real time update Selecting time zone You can choose your own time zone from the drop down box If you check the Automatically adjust for daylight saving time changes it allows the daylight saving time to be applied according to your zone setting Setting current time of server Select one of 3 options e Synchronize the server with your PC time e Synchronize the server with NTP server via internet e Set the server time manually by user 01A 03 Dante Security Inc 28 DN9231 User s Manual Periodical time synchronization NTP server Server time is synchronized with NTP server You can configure available NTP servers at Setup System Options NTP Totally 4 of NTP servers can be added and the first one is set as the default server ntp1 usv ro Real Time Clock on system Server time is synchronized with Real time clock in the server The clock is attached to the board of the product internally and the clock is recharged automatically when the server is started Interval of synchronization Everyday 00 00 Synchronizes at every midnight Disabled Synchronizes only when the decoder is rebooted factory default 01A 03 Dante Security Inc 29 DN9231 User s Manual To configure encoder channels on a display monitor that is connected to a decoder go the Setup Encoder Configuration Connection The channel connection mode is divided into two types Instant and Preset If you click on Instant or
34. er s Manual 2 3 2 Rear Panel DI RS 232 2 z Rx rx If s I p d L3 ie E gt LOT USB Ethernet Aout DO RS485 G 4 USB 2 0 port Use this port to connect a USB mouse A USB mouse is required to control the device on a monitor The PS 2 mouse is not supported 5 LAN connector Use this RJ45 LAN connector for connecting the device to network or supplying PoE power 6 Audio IN OUT The decoder has one channel mono audio input output It supports bi directional audio communication between an H 264 encoder and the decoder Since the output power for the audio is low an amplifier speaker is needed 7 Di Do The encoder supports two channels for each of DI and DO Refer to the section 3 2 Cabling for more specific information RS 232 RS 485 RS 232C Terminal Block is used for some devices such as POS terminal block RS 485 is used for PTZ controls 9 Reset Reboot the device system or reset the device to its Factory default settings Refer to the section 4 4 Reset for more specifi
35. es go to Setup System Options SNMP The Simple Network Management Protocol SNMP is literally the protocol for managing network By retrieving the system information it allows to manage network architecture performance device and security To enable SNMP select the Enable check box The encoder supports SNMP version 2c and 3 SNMP Setting Configuration Enable SNMP information Input your SNMP information on the following section For the Read Community input the community name which is the authorized ID for reading SNMP data The factory default value is public SNMP Description Location New York Contact tester test com Read Community public Trap setting The Trap can be considered as sending an event message from an event publisher such as DIO and VCA Choose the SNMP Trap version to receive Trap event and input the IP address and community on the text box Trap Setting Trap Ver1 0 Trap Ver2 0 One white space must be inserted between ip address and community at trap parameter 192 168 0 1 public 0 For the details about SNMP MIB information please contact our support team Note 01A 03 Dante Security Inc 47 DN9231 User s Manual 6 7 10 CONFIGURATION 6 1 1 DI DO control To set up DI DO and UART go to Setup IO Configuration DI DO In case of using additional device such as alarm system or sensor system you can configure the DI Digital Input and DO Digital Out in this
36. file 4 Click the Apply button and then the log file will be created ps If you want to see the log list click the LOG LIST button Name The log files are named automatically It s not allowed for user to name it manually Size Log file size is updated in real time Latest access time Latest time when the product accessed the internal system to get the log LOG LIST Name Size Byte Latest access time Displays the files messages 12566 Thu Feb 5 06 13 28 2009 created messages 0 65609 Thu Feb 5 06 11 36 2009 messages 1 65557 Thu Jan 29 01 22 33 2009 messages 2 65562 Wed Jan 28 08 48 37 2009 messages 3 65617 Sun Jan 18 03 33 15 1970 messages 4 65572 Sat Jan 17 20 55 21 1970 Renew 01A 03 Dante Security Inc 53 DN9231 User s Manual 6 9 ABOUT To find the product information including the hardware specification and software version go to the About page by selecting Setup gt About This menu is configured with two sub menus Version and Licenses 6 9 1 Version On the Version page you can find the information about the current firmware version on the top of the page Other detailed information for its hardware and software configuration is found in this page as well Refer to the following list for the provided information Hardware MAC address Microprocessor Bootloader Kernel Root filesystem APP filesystem Webpage ActiveX SSSDK HTTP API VCA Tracker ufs Language Video in Video out
37. hernet PoE standard IEEE 802 3af allows for two power options for Category 5 cables The PoE module signature and control circuit provides the PoE compatibility signature and power classification required by the Power Sourcing Equipment PSE before applying up to 15W power to the port The high efficiency DC DC converter operates over a wide input voltage range and provides a regulated low ripple and low noise output The DC DC converter also has built in overload and short circuit output protection Note For proper activation of 12V PoE the Category 5 cable must be shorter than 140m and conform the PoE standard With non Power Sourcing Equipment PSE When it is connected with non PSE the power adaptor should be connected With power adaptor Connecting both PSE and power adaptor does not do any harm to the products Disconnecting power adaptor while it is operating does not stop operation The product continues to work without rebooting The PoE Power Class supported by the IP device is Class O Class Usage Minimum Power Levels Maximum Power Levels at the at the PSE NT TTC Device o mk saw owmtenow 01A 03 Dante Security Inc 57 DN9231 103 36 User s Manual 37 66 121 1 146 38
38. mp 1 J Stream 1 Channel 2 Stream 2 Channel 3 Channel 4 31No device 7 Checkifthe streaming video of selected IP device is displayed on the screen 01A 03 Dante Security Inc 17 DN9231 User s Manual The video output configuration must be set before you turn on the device Changing the setting after the device is turned on will not affect on the Note configuration Video transport performance The videos displayed on the 4 channels in a view may not have satisfactory quality due to limitation of DSP resource To configure the channels with a relevant level refer to the following test table for video transport performance 29 If you want to keep one of the four channels to have the best image quality without interference of other three channels you can use the Priority Channel Configuration option on the web page of your device Refer to the Quad Mode Setting on 6 4 1 View for more details 60 L 929 4 4 Reset Perform the following procedures to reset your device 1 While the device is in use press and hold the Reset button 2 Release the Reset button after 3 seconds 3 Wait for the system to reboot 4 9 Factory Default If you reset your device to the factory default setting all parameters including the IP address will be initialized For the Factory Default reset 1 Disconnect the power supply from the device 2 Connect the power to the device with the Reset button pressed
39. o get the event notification from the device and send them to the client application This page helps you to configure the HTTP server HTTP Server Setting HTTP Server 1 HTTP Server 2 HTTP Server 3 HTTP Server 4 Configuration Type a message default Original a name to show message format is Address http 11 192 168 0 160 17272 1 655355 Type IP address and port of HTTP server shown no parsed data customerO You can customize the message format by configuring it with HTTP CGI and parameters Syntax Format default v Message Enable Option type s info s Timeout Type the desired waiting time from HTTP server until the response is arrived 01A 03 Dante Security Inc 36 DN9231 User s Manual 6 9 2 Assigning event rule to event publishers Publishers Subscribers DO Email Multicast TCP HTTP Email Multicast TCP HTTP Network Email Multicast TCP Health Multicast TCP The below is an example page of DI event configuration For each event server setting refer to the section 6 4 1 How to configure each event server Publisher DI Subscriber DO DI 1 4 DO 1 DO 2 DI 2 DO 1 4 DO 2 Subscriber Email Post notification message Attach a snapshot Subscriber Multicast Post notification message Subscriber TCP 4 Post notification message Subscriber HTTP HTTP Server 1 HTTP Server 2 HTTP Server 3 HTTP Server 4 Apply
40. oder Information Encoder Type TYPEO Session Type UNICAST TCP Encoder URL 192 168 83 38 hostname ar ip address Enable encrypted connection SSL HTTP Port 0 1 65535 The audio out stream from the decoder to an encoder is only available when you select TYPEO H 264 encoder for Encoder Type TYPE1 or RTSP is not Note supported 01A 03 Dante Security Inc 30 DN9231 User s Manual Login Information Enter the login information for the webpage of the encoder to connect Logon Information Username root Password IIIIIII Encoder Channel amp Stream Select the channel number of the encoder and its stream number After the setup click the Apply button on the bottom of the Encoder Setting window And then go to the Connection Mode Setting page select the mode to apply changes and click the Apply button on the bottom 01A 03 Dante Security Inc 31 DN9231 User s Manual 6 4 Decoder Setting 6 4 1 View To set up how to display videos on the screen go to Setup Decoder Configuration Decoder In this page you can configure video display mode screen margin channel specification in display modes etc Refer to the following for more details Checking video out format On the top of the page you can check the current video out standard format A user cannot change the format on the web page but only by using the video output configuration switch on the decoder Video Out Standard Format NTSC PAL
41. ply a suitable value To test the cursor acceleration more clearly jump the cursor to travel long distances Cursor Cursor auto hide time 2 sec 0 600 0 all ready show Cursor Acceleration J 30 0 255 Cursor Speed J 20 0 255 Setting the position of OSD The default position of OSD which is IP address on left top FPS on left bottom and shortcut icon on right top can be changed according your configuration You can apply a different 01A 03 Dante Security Inc 33 DN9231 User s Manual setting for each channel and each view mode If you want to put the OSD at a customized position other than the corners of screen select normalized X Y for the Predefined option and input the normalization value on the text box of X Y The normalization range of X and Y is from O to 9999 IP address Predefined left top Y X Y FPS Predefined left bottom bi X Y Shortcut icon Predefined right top XV 6 4 3 Audio The decoder supports two way mono audio On the web page you can configure the audio input volume and output channel or volume Audio Output The compressed audio stream can be sent to H 264 encoder only To enable the audio output from the decoder select the Talk to the speakers of encoder channel check box and configure the desired volume level If you connect a microphone on the device and prepare an encoder with a speaker you can hear the input sound volume Audio Input You to set the volume of
42. re valid for one day even if you disable this mode The default web server setting the device is HTTP If you want to change its setting to HTTPS to enhance its access security select the HTTPS option What is SSL SSL is the abbreviation of Secure Socket Layer SSL protects web server and makes it easy for users to trust the contents When you use HTTPS for communication with server the SSL certificate is required for the web server and the certificate enables encryption of video and audio data during online transactions OpenSSL is one of the data security protocols for Linux system which is used for the product Setting the port number of web server To communicate with server by HTTP or HTTPS with TCP the port number can be fixed between 1 and 65535 The factory default is set as 443 Redirecting HTTP to HTTPS Even if a user tries to access the server with http you can enable the server to be redirected to HTTPS In this case do not set 80 for port number because it can cause a conflict with HTTP port Cache Control To save the webpage loading time you can use the cache control setting If the content expiration mode is enabled specific pages and images will be stored in client cache and be retrieved from it for one day Once the mode is enabled the resources in the cache are valid for one day even if you disable this feature It is because the content expiration time is basically set to one day Therefore to avoid retrieving
43. riority Channel Configuration Enable Priority Priority channel e CH 1 CH 2 CH 3 CH4 Adjusting image margin The image margin can be adjusted on the web page The adjusted margin will be displayed in black on the screen Adjust left margin J 0 128 step 16 right margin J 0 128 step 16 top margin J 0 0 64 step 4 bottom margin J 0 0 64 step 4 Margin O Supported value Left and right Multiplies of 16 up to 128 Top and bottom Multiplies of 4 up to 64 6 4 2 0SD To configure how to display OSD menus on the screen go to Setup gt Decoder Configuration gt OSD The configurable OSD includes the IP address of connected encoder shortcut icon and FPS Setting time to hide OSD You can set the time that OSD remains on the screen after stopping operations If you set the OSD auto hide time to 3 seconds the OSD will be disappeared on the screen 3 seconds after operation done Setting this time to O will display the OSD all the time Configuration OSD auto hide time 3 sec 0 600 0 all ready show Setting time for mouse cursor operation For the mouse cursor on the screen you can set its time for being remained after operation done and its movement speed If you set the auto hide time to O the cursor will be displayed on the screen all the time even though there is no movement of the cursor For the best operation of your mouse on the screen test its cursor movement speed and ap
44. rt My network Places displays the devices by UPnP Customize Manufacturer Description If you want to have your own manufacturer s name for the device to be shown on the UPnP program type name and URL Then The UPnP program will show the modified name and URL Customize Model Description If you want to have your own model name for the device to be shown on the UPnP program type name description and URL of them Then The UPnP program will show the modified name description and URL 6 6 4 mDNS Multicast DNS setup For the multicast DNS setting go to Setup gt System Options gt mDNS Configuration V Enable Friendly name Decoder Manufacturer Description Name CAP URL http www Model Description Mame Decoder Description Decoder URL http www 01A 03 Dante Security Inc 42 DN9231 User s Manual If you have your own program or device which is required to use the mDNS this page helps you to customize the name of model and manufacturer instead of factory default Configuration If you check the box of Enable mDNS is activated You can type the Friendly Name to be shown on the application program Customize Manufacturer Description You can type the manufacturer s name and home URL of your device The given company name is typed as a default for the name but it is adjustable as you want Customize Model Description You can type the model name description of the model and URL of your device
45. ser s Manual 9 2 Display Mode The device supports quad view single view and PIP view The default view mode is quad view 9 2 1 Quad View In the Quad View mode the evenly split four windows appear on the screen On the quad view mode you can change the view to the single view mode only To change the display mode on this default view mode move your mouse point to the right top of the desired channel Then image icons appear as shown below If you click the Display Mode icon the selected split view is displayed in a single view 1 Enable audio 2 Enable single view 9 2 2 Single View In the Single View mode only one video is displayed on the screen You can change the view either to a different channel or to different splits To change the display mode to different views move your mouse point to the right top of the view Then image icons appear as shown below Select the desired view mod D Enable audio Enable quad view 3 Switch the channel Enable PIP mode 9 2 3 PIP View In the PIP View mode you can see one other video with a small split in a full single view You can switch the full image with the small inset image or change the view with different splits To switch the image that is displayed in the sub window with the full screen image click 1 below To switch the channel in the sub window to a different channel click the desired channel from 2 If you want to change the view mode from PIP to a
46. t connection modes Instant Mode and Preset Mode The instant mode enables you to immediately change the video channels and display them on the screen The preset mode is useful to save the channels you want to view and display them just by clicking the configured preset view The preset mode is supported with up to 8 different configurations To configure desired channels on a preset mode 1 Right click on a view to display the quick menu 2 Select the desired number of preset mode 3 Select the encoders you want to display by referring to 4 3 Video Display 4 Right click on a view to display the quick menu 01A 03 Dante Security Inc 21 DN9231 User s Manual 5 Click the Save button Then the quick menu disappears and the view of the saved preset mode is displayed To change the connection mode 1 Right click on a view to display the quick menu 2 Select the desired connection mode from the list e g Preset 82 3 Click the Change button then the view is changed to the selected connection mode 9 4 2 Checking device and channel information You can check the device information and the channel configuration with the quick menu If you click the Version button the device name and its OSD version will be displayed on a pop up window For the channel configurations of the selected connection mode click the Detail button on the quick menu Then following pop up window appears on the screen Current mode instan
47. t mode Channel 1 Device http 192 168 21 227 80 it nvcich nncl Ll first stream Channel 2 Device http 192 168 15 126 80 it nvcicha nnci l first stream Channel 3 Device http 192 168 17 9 80 1 nvcichannel l first stream Channel Wa Device httpz 102 168 79 2 442 nve channell first stream On the pop up windows you can check its connection mode and the IP address encoder channel number and stream number for each channel 9 4 3 Rebooting device You can reboot your device by using the quick menu To reboot your device right click on a view to display the quick menu and click the Reboot button While rebooting the device no image will be appeared on the screen It takes more than a minute to restart the device To reboot your device with the Reset button on the device refer to 4 4 Reset If you click the Reboot button the device immediately starts rebooting without an alarm message Check if the device reboot is really required before you click Note this button 01A 03 Dante Security Inc 22 DN9231 User s Manual On the web page of this device you can configure required settings The following summarizes the supported features of the web page Basic configuration Encoder connection mode setting Decoder setting Event configuration System option setting System maintenance Device information query To learn how to access to the web page refer to 4 2 System Configuration on Web Page Not
48. the designated squid server s IP correctly with red characters 5 Click Apply button and it will be restarted 6 6 3 UPnP setup To change the Universal Plug amp Play configuration go to Setup gt System Options gt UPnP Configuration Enable Friendly name Decoder Manufacturer Description Name CAP URL http www Model Description Name Decoder Description Network Video Decoder URL http www UPnP allows IP devices to connect seamlessly and to simplify the implementation of networks in remote PC environments Refer to the example of UPnP of Windows XP so that you can check out how the customized settings are being applied Find this information on your PC Start My network places Find your device right click the mouse and go to property 01A 03 Dante Security Inc 41 DN9231 User s Manual e g Customized UPnP name and description CAM_MAIN GATE 00 13 23 04 0B 04 Properties General Friendly name SA uj CAM MAIN GATE POTT s 23 04 0B8 04 Manufacturer ABCDE Corp Model Name ABCDE_CAM Model Number 0 99 05 Manufacturer name Model name Description Decoder Device Address http 192 168 11 4 49152 upnpindex html Model description Close Configuration If you want to enable UPnP to search your device check the box of Enable UPnP Friendly Name Type any friendly name to be shown by the UPnP program You can test it easily with Windows as well Sta
49. the setting 3 Click the Modify button below the User List 4 When the pop up window appears type a new password If you want to change your user group only skip to step 6 Type the same password again on the text box of Confirm password Select the desired user group 7 Click the OK button to save the changes nu The user name is not allowed to be changed If you want to modify the current user s name just remove it and add a new user Note To remove a user name form the User List 1 Go Setup gt Basic Configuration gt Users 2 Select the user name to remove on the User List 01A 03 Dante Security Inc 25 DN9231 User s Manual 3 Click the Remove button below the User List 4 Whenthe dialog box appears to confirm your request click the OK button 5 Checkif the user name is removed from the list on the page 6 2 2 Configuration of HTTP and HTTPS To set the protocol for the product web server go the Web Server page by clicking Setup Basic Configuration Web Server Web Server HTTP S Settings HTTPS OpenSSL v2 v3 4 Redirect HTTP to HTTPS HTTPS Port 80 is not allowed for redirecting HTTP to HTTPS HTTP Port Settings TCP IP port number of HTTP or HTTPS 443 1 65535 Cache Control Enable content expiration Default off If the content expiration mode is enabled specific resources will be retrieved from client cache for one day Once the mode is enabled the resources in the cache a
50. tion by email This page helps you to configure the Email server Attaching a snapshot in an e mail is not supported Automatically configured according to the setting page of System Options SMTP email Type the mail receivers subject and contents of email 2 Multicast server Email Setting Configuration To eventreceive test com Cc Bcc Subject Notification of Events Detection Contents Email Event Cancel You can use Multicast server to get the event notification from the device and send them to the client application This page helps you to configure the Multicast server Multicast Setting Configuration Enable Multicast Event Name Address Port 1 65535 TTL 1 255 count 1 Multicast Event 1 limit to subnet 255 unlimited 01A 03 Dante Security Inc Type a message name to show on event message program Type Address port and TTL according to your system setting Factory default is 2555 35 DN9231 User s Manual 3 TCP server You can use TCP server to get the event notification from the device and send them to the client application This page helps you to configure the TCP server TCP Setting Configuration Enable TCP Event Type a message name to show on xs event message program 1 65535 255 ee eT Type port number according you will use for TCP message Factory default is 2555 4 HTTP server You can use HTTP server t
51. tta teer es 0 57 Meglio er tesa a ee an RL ieee tosses eta ets eee 57 APPENDIX C DIMENSIONS in den ceat la exp cu Evae ie die eo do veo Roe Ee 58 REVISION HISTORY sn stades a douanes n encens dede scie vised 59 01A 03 Dante Security Inc 3 DN9231 User s Manual INFORMATION TO USER CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SEERIVCE PERSONEL dangerous voltage within the product s enclosure that may be of sufficient This symbol is intended to alert the user to the presence of un insulated magnitude to constitute a risk of electric shock to persons This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance 01A 03 Dante Security Inc 4 DN9231 User s Manual 1 PACKAGE CONTENTS Unpack carefully and handle the equipment with care The packaging contains Decoder DC power adaptor Screws and anchor blocks Quick installation guide LA The above contents are subject to change without prior notice Note 01A 03 Dante Security Inc 5 DN9231 User s Manual 2 INTRODUCTION 2 1 Main Features The Network Video Decoder enables decoding of H 264 MPEG4 and MJPEG streams from IP devices and displaying de
52. ut voltage threshold 1 V Description Connect cable of electronic power source for sensors to this port as shown in the circuit above Connect output of sensors for each port as shown in the circuit above N Do not exceed the maximum input voltage or relay rate Do not use voltage and relay type sensor together Caution 01A 03 Dante Security Inc 11 DN9231 User s Manual Alarm Output D 0 Only the relay type is supported Relay Rating Max 24VAC 500mA or 12VDC 1A Do not exceed the maximum relay rating Caution Internal Device Max 12VDC 1A or 24VAC 500mA Relay Type Power 01A 03 Dante Security Inc 12 DN9231 User s Manual RS 232C Connection RS 232C Terminal Block is used for some devices such as POS terminal block lt RS 232C Application RX TX IN TX RX GND GND NU 4 N RX TX GND RS 485 Connection The RS 485 serial port consists of TRX RX and TRX RX as following lt R5 465 Applicat on gt 485 Device 01A 03 Dante Security Inc 13 DN9231 User s Manual To wall mount your device follow the instructions below 1 Drill two holes on the wall and insert anchor blocks into the holes Put the mounting brackets to the mounting hole on each side of the device Fasten the device with screws Make sure the device is firmly installed KS

DN9231 - Dante Security

Contents

Download Pdf Manuals

Related Search

Related Contents