BLE113 Datasheet
Contents
1. mule Bano ait aa 4 3 2 1 0 2 rant MI m PX __ 55 m Refer to Profile Toolkit Developer Guide for detailed settings fe HARDWARE XML Example usart channel 0 mode spi_master alternate 1 usart channel 0 mode spi_master alternate 2 usart channel 0 mode uart alternate 1 usart channel 0 mode uart alternate 2 usart channel 1 mode spi master alternate 1 lt usart channel 1 mode spi master alternate 2 lt usart channel 1 mode uart alternate 1 lt usart channel 1 mode uart alternate 2 timer index 1 alternate 1 timer index 1 alternate 2 timer index 3 alternate 1 lt timer index 3 alternate 2 timer index 4 alternate 1 timer index 4 alternate 2 SS is the slave select signal when BLE113 is set as SPI slave When set as SPI master any available I O can be used as chip select signal of BLE113 APC Hero 01480 226600 sales apc hero co uk Table 3 Peripheral I O Pin Mapping Bluegiga Technologies Oy Page 9 of 30 2 1 I O Ports Each I O port except pins 1 0 and P1 1 can be configured as an input with either internal pull up or pull down or tri state Pull down or pull up can only be configured to whole port not individual pins Unused I O pins should have defined level and no2. 18 input extended interrupt unit The memory arbiter is at the heart of the system as it connects the CPU and DMA controller with the physical memories and all peripherals through the SFR bus The memory arbiter has four memory access points access of which can map to one of three physical memories an SRAM flash memory and XREG SFR registers It is responsible for performing arbitration and sequencing between simultaneous memory accesses to the same physical memory The SFR bus is a common bus that connects all hardware peripherals to the memory arbiter The SFR bus also provides access to the radio registers in the radio register bank even though these are indeed mapped into XDATA memory space APC Hero Bluegiga Technologies Oy 01480 226600 Page 23 of 30 sales apc hero co uk The 8 KB SRAM maps to the DATA memory space and to parts of the XDATA memory spaces The SRAM is an ultralow power SRAM that retains its contents even when the digital part is powered off power modes 2 and 3 The 128 256 KB flash block provides in circuit programmable non volatile program memory for the device and maps into the CODE and XDATA memory spaces Peripherals Writing to the flash block is performed through a flash controller that allows page wise erasure and 4 bytewise programming A versatile five channel DMA controller is available in the system accesses memory using the XDATA memory space and thus has access to all physical memories Each
3. PA 10 2 IGOS RITTER 11 2 4 Absolute Maximum Ratings pp 11 2 5 Recommended Operating Conditions sise 11 E NEED GIOI t eee eee 11 27 CUOMO ON AA 12 2 8 Antenna TOT 13 SME Physical Dimensions ERE 16 4 Power On Reset and Brownout Detector 4 18 AA 19 SECO EB ee el AP 19 S Eyonu Cde MIB NORTE 19 Eye 20 6 Soldering Recommendations pp 22 T 23 26 Sal mt 26 B _ ___ ___ 26 CE AA 29 NU 29 MEE NG GA 29 COPECO diio AA 30 01480 226600 Bluegiga Technologies Oy sales apc hero co uk blue BLE113 Bluetooth Smart Module DESCRIPTION BLE113 is a Bluetooth Smart module targeted for small and low power sensors and accessories It integrates all features required for a Bluetooth Smart application Bluetooth radio software stack and GATT based profiles BLE113 Bluetooth Smart module can also host end user applications which means no external micro controller is required in size or price constrained devices BLE113 module has flexible hardware interfaces to connect to different peripherals and sensors BLE113 can be
4. channel trigger priority transfer mode addressing mode source and destination pointers and transfer count is configured with DMA descriptors that can be located anywhere in memory Many of the hardware peripherals AES core flash controller USARTs timers ADC interface etc can be used with the DMA controller for efficient operation by performing data transfers between a single SFR or XREG address and flash SRAM Each CC2541 contains a unique 48 bit IEEE address that can be used as the public device address for a Bluetooth device Designers are free to use this address or provide their own as described in the Bluetooth specification The interrupt controller services a total of 18 interrupt sources divided into six interrupt groups each of which is associated with one of four interrupt priorities MO and sleep timer interrupt requests are serviced even if the device is in a sleep mode power modes 1 and 2 by bringing the CC2541 back to the active mode The debug interface implements a proprietary two wire serial interface that is used for in circuit debugging Through this debug interface it is possible to erase or program the entire flash memory control which oscillators are enabled stop and start execution of the user program execute instructions on the 8051 core set code breakpoints and single step through instructions in the code Using these techniques it is possible to perform in circuit debugging and external flash programm
5. et 2 ce dispositif doit accepter toute perturbation y compris les perturbations qui peuvent entrainer un fonctionnement non d sir du dispositif Selon les r glementations d Industrie Canada cet metteur radio ne doit fonctionner qu avec une antenne d une typologie sp cifique et d un gain maximum ou inf rieur approuv pour l metteur par Industrie Canada Pour r duire les ventuelles perturbations radio lectriques nuisibles d autres utilisateurs le type d antenne et son gain doivent tre choisis de mani re ce que la puissance isotrope rayonn e quivalente P I R E n exc de pas les valeurs n cessaires pour obtenir une communication convenable Responsabilit s des OEM quant la conformit avec les r glementations de FCC et d Industrie Canada Les modules BLE113 ont t certifi s pour entrer dans la fabrication de produits exclusivement r alis s par des int grateurs dans les conditions suivantes APC Hero Bluegiga Technologies Oy 01480 226600 Page 27 of 30 sales apc hero co uk e l antenne ou les antennes doit tre install e de facon maintenir tout instant une distance minimum de 5 mm entre la source de radiation l antenne et toute personne physique e Le module transmetteur ne doit pas tre install ou utilis en concomitance avec une autre antenne ou un autre transmetteur Tant que ces deux conditions sont r unies il n est pas n cessaire de proc der des tests suppl mentai
6. interference that may cause undesired operation of the device Under Industry Canada regulations this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication OEM Responsibilities to comply with FCC and Industry Canada Regulations The BLE113 module has been certified for integration into products only by OEM integrators under the following condition e he antenna s must be installed such that a minimum separation distance of 5 mm is maintained between the radiator antenna and all persons at all times e he transmitter module must not be co located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi transmitter product procedures APC Hero Bluegiga Technologies Oy 01480 226600 Page 26 of 30 sales apc hero co uk As long as the two condition above is met further transmitter testing will not be required However the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed for example digital device emissions PC peripheral requirements etc IMPORTANT NOTE In the event that these conditio
7. is recommended to place a 100uF capacitor in parallel with the battery The internal resistance of a coin cell battery is initially in the range of 10 ohms but the resistance increases rapidly as the capacity is used Basically the higher the value of the capacitor the higher is the effective capacity of the battery and thus the longer the life time for the application The minimum value for the capacitor depends on the end application and the maximum transmit power used The leakage current of a 100uF capacitor is the range of 0 5 uA to 3 uA and generally ceramic capacitors have lower leakage current than tantalum or aluminum electrolytic capacitors Optionally Tl s TPS62730 can be used to reduce the current consumption during TX RX and data processing stages TPS62730 is an ultra low power DC DC converter with by pass mode and will reduce the current consumption during transmission nominally by 20 when using 3V coin cell battery it PROGRAMMING INTERFACE Figure 11 Example schematic for BLE113 with a coin cell battery TPS62730 DCDC converter and an I2C accelerometer 5 2 Layout Guide Lines Use good layout practices to avoid excessive noise coupling to supply voltage traces or sensitive analog signal traces If using overlapping ground planes use stitching vias separated by max 3 mm to avoid emission from the edges of the PCB Connect all the GND pins directly to a solid GND plane and make sure that there is a low im
8. lO pin pull up and pull down resistors 20 Logic 0 output volatge 4 mA pins Outputload 4mA J O05 V Logic output voltage 4 mA pins OutoputloaddmA 24 X V For detailed terminal characteristic and timings refer to the CC2541 datasheet available in http www ti com lit ds symlink cc254 1 pdf APC Hero Bluegiga Technologies Oy 01480 226600 Page 11 of 30 sales apc hero co uk 2 Current Consumption Men lt txpower power 1 gt 18 2 slow clock enable true gt lt txpower power 7 gt KA slow clock enable true gt lt txpower power 15 gt slow clock enable true gt Transmit lt txpower power 1 gt slow clock enable false gt WE seed E power 7 gt WE seed E clock enable z false LG paaa power 15 gt LG paaa clock enable false gt slow clock enable true gt Receive T slow clock enable false Table 7 Current consumption of BLE113 TX Peak CUrrent mA 6 8 10 txpower power X Figure 2 BLE113 TX peak current as a function of the setting in the HW configuration file APC Hero Bluegiga Technologies Oy 01480 226600 Page 12 of 30 sales apc hero co uk E 2 eu gt lt i 6 8 10 txpower power gt Figure 3 BLE113 TX power as a function of the setting in the HW con
9. the number of periods that have transpired A 40 bit capture register is also used to record the exact time at which a start of frame delimiter is received transmitted or the exact time at which transmission ends There are two 16 bit timer compare registers and two 24 bit overflow compare registers that can be used to give exact timing for start of RX or TX to the radio or general interrupts Timer 3 and timer 4 are 8 bit timers with timer counter PWM functionality They have a programmable prescaler an 8 bit period value and one programmable counter channel with an 8 bit compare value Each of the counter channels can be used as PWM output USART 0 and USART 1 are each configurable as either an SPI master slave or a UART They provide double buffering on both RX and TX and hardware flow control and are thus well suited to high throughput full duplex applications Each USART has its own high precision baud rate generator thus leaving the ordinary timers APC Hero Bluegiga Technologies Oy 01480 226600 Page 24 of 30 sales apc hero co uk free for other uses When configured as SPI slaves the USARTs sample the input signal using SCK directly instead of using some oversampling scheme and are thus well suited for high data rates The AES encryption decryption core allows the user to encrypt and decrypt data using the AES algorithm with 128 bit keys The AES core also supports ECB CBC OFB CTR and as well as hardware s
10. BLE113 PRELIMINARY DATA SHEET Tuesday 07 May 2013 Version 0 55 __ APCHero 01480 226600 sales apc hero co uk Copyright 2000 2013 Bluegiga Technologies All rights reserved Bluegiga Technologies assumes no responsibility for any errors which may appear in this manual Furthermore Bluegiga Technologies reserves the right to alter the hardware software and or specifications detailed here at any time without notice and does not make any commitment to update the information contained here Bluegiga s products are not authorized for use as critical components in life support devices or systems The WRAP is a registered trademark of Bluegiga Technologies The Bluetooth trademark is owned by the Bluetooth SIG Inc USA and is licensed to Bluegiga Technologies All other trademarks listed herein are owned by their respective owners APC Hero 01480 226600 Bluegiga Technologies Oy sales apc hero co uk VERSION HISTORY Version Comment Confidential watermark added Marketing information updated 0 4 Current consumption recommended land pattern layout guide example schematic antenna characteristics ET E omens ooo Dimensions APC Hero 01480 226600 Bluegiga Technologies Oy sales apc hero co uk TABLE OF CONTENTS 7 B E I 19 Rm 6 2 Pinout and Terminal Description 4 y E GU AA 10 Re PANG ANNA
11. a Technologies Oy Page 6 of 30 Pinout and Terminal Description JOO IN JU IB JW IN NUMBER ae RESET 4 GND DVDD AVDD a 5550 GND NC Reset PO 0 PO 1 PO 2 PO 3 PO 4 PO 5 PO 6 PO 7 GND eR e Cl str NENT NI CN Figure 1 BLE113 PAD TYPE DESCRIPTION Active low reset GND GND 36 35 34 33 32 31 30 29 28 27 26 25 Supply voltage upply voltage 2V 3 6V Supply voltage upply voltage 2V 3 6V Table 1 Supply and RF Terminal Descriptions APC Hero 01480 226600 sales apc hero co uk Bluegiga Technologies Oy Page 7 of 30 PIN NUMBER PIN NAME PIN TYPE DESCRIPTION 9 Pag 19 P14 0 P1 4 2 Digital I O Configurable I O port See table 3 6 P06 m CJ 22 L 26 2 2 2 2 3 3 3 2 N i Er ieee NG Configurable I O port with 20mA driving capability See table 3 E Can be used as IC clock pin or digital I O Leave SCL a EM floating if not used If grounded disable pull up 7 Can be used as I C data pin or digital I O Leave 15 SDA 2 floating if not used If grounded disable pull up Table 2 Terminal Descriptions 0 1 2 3 UJ UJ 8 14 BLE113 is configurable as either SPI master or SPI slave APC Hero Bluegiga Technologies Oy 01480 226600 Page 8 of 30 sales apc hero co uk PERIPHERAL FUNCTION FA aa 3 aga ana USART 0 UART
12. cs APC Hero Bluegiga Technologies Oy 01480 226600 Page 25 of 30 sales apc hero co uk 8 Certifications BLE113 is compliant to the following specifications 8 1 Bluetooth TBA 8 2 FCC and IC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by Bluegiga Technologies could void the user s authority to operate the equipment FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance This transmitter meets both portable and mobile limits as demonstrated in the RF Exposure Analysis and should not be used closer than 5 mm from a human body in portable configuration This transmitter must not be co located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi transmitter product procedures IC Statements This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including
13. figuration file 2 8 Antenna characteristics The antenna is monopole type of chip antenna The antenna impedance matching is optimized for 1 mm 2 mm mother board PCB thickness The radiation pattern is impacted by the layout of the mother board Typically the highest gain is towards GND plane and weakest gain away from the GND plane Figures 4 6 show the radiation pattern of BLE113 when mounted to the development board The typical efficiency of the antenna is 25 35 depending on the mother board layout Maximum gain is 0 5 dBi APC Hero Bluegiga Technologies Oy 01480 226600 Page 13 of 30 sales apc hero co uk Legend 2400 00 MHz 2440 00 MHz 2485 00 MHz Figure 4 Radiation pattern of BLE113 top view Udeg Legend 2400 00 MHz 2440 00 MHz 2485 00 MHz 270deg 180dea Figure 5 Radiation pattern of BLE113 front view APC Hero Bluegiga Technologies Oy 01480 226600 Page 14 of 30 sales apc hero co uk Figure 6 Radiation pattern of BLE113 side view APC Hero Bluegiga Technologies Oy 01480 226600 Page 15 of 30 sales apc hero co uk 3 Physical Dimensions 1 50mm 5 35mm 0 50mm 1 0 80mm 4 15 725mm 0 300mm Figure 7 Physical dimensions and pinout top view 15 73 mm 0 1mm 0 9 E lt a 0 6 gt 5 53 mm 9 6 mm 0 6 mm Figure 8 Physical dime
14. frequencies 3 50mm Board outline learance Figure 14 Recommended layout for BLE113 A APC Hero Bluegiga Technologies Oy 01480 226600 Page 20 of 30 sales apc hero co uk 0 2500 2550 Freq MHz Figure 15 Typical return loss of BLE113 A with two different mother board PCB thickness APC Hero Bluegiga Technologies Oy 01480 226600 Page 21 of 30 sales apc hero co uk ero 6 Soldering Recommendations BLE113 is compatible with industrial standard reflow profile for Pb free solders The reflow profile used is dependent on the thermal mass of the entire populated PCB heat transfer efficiency of the oven and particular type of solder paste used Consult the datasheet of particular solder paste for profile configurations Bluegiga Technologies will give following recommendations for soldering the module to ensure reliable solder joint and operation of the module after soldering Since the profile used is process and layout dependent the optimum profile should be studied case by case Thus following recommendation should be taken as a starting point guide Refer to technical documentations of particular solder paste for profile configurations Avoid using more than one flow Reliability of the solder joint and self alignment of the component are dependent on the solder volume Minimum of 150um stencil thickness is recommended Aperture size of the stencil should be 1 1 with the
15. ification FCC QOQBLE113 Contient module metteur IC 5123A BGTBLE113 OU Contient identification FCC QOQBLE113 Contient IC 5123A BGTBLE113 Dans le guide d utilisation du produit final l int grateur OEM doit s abstenir de fournir des informations l utilisateur final portant sur les proc dures suivre pour installer ou retirer ce module RF ou pour changer les parametres RF APC Hero Bluegiga Technologies Oy 01480 226600 Page 28 of 30 sales apc hero co uk 8 3 CE TBA 8 4 MIC Japan TBA 8 5 KCC Korea APC Hero Bluegiga Technologies Oy 01480 226600 Page 29 of 30 sales apc hero co uk 9 Contact Information Sales Technical support Orders WWW Head Office Finland Postal address Finland Sales Office USA Sales Office Hong Kong APC Hero 01480 226600 sales bluegiga com support bluegiga com http techforum bluegiga com orders bluegiga com www bluegiga com www bluegiga hk Phone 358 9 4355 060 Fax 358 9 4355 0660 Sinikalliontie 5A 02630 ESPOO FINLAND P O BOX 120 02631 ESPOO FINLAND Phone 1 770 291 2181 Fax 1 770 291 2183 Bluegiga Technologies Inc 3235 Satellite Boulevard Building 400 Suite 300 Duluth GA 30096 USA Phone 852 3972 2186 Bluegiga Technologies Ltd Unit 10 18 32 F Tower 1 Millennium City 1 388 Kwun Tong Road Kwun Tong Kowloon Hong Kong Bluegiga Technologies Oy sales apc hero c
16. ing elegantly The I O controller is responsible for all general purpose I O pins The CPU can configure whether peripheral modules control certain pins or whether they are under software control and if so whether each pin is configured as an input or output and if a pullup or pulldown resistor in the pad is connected Each peripheral that connects to the I O pins can choose between two different I O pin locations to ensure flexibility in various applications The sleep timer is an ultra low power timer that uses an external 32 768 kHz crystal oscillator The sleep timer runs continuously in all operating modes except power mode 3 Typical applications of this timer are as a real time counter or as a wake up timer to exit power modes 1 or 2 Timer 1 is a 16 bit timer with timer counter PWM functionality It has a programmable prescaler a 16 bit period value and five individually programmable counter capture channels each with a 16 bit compare value Each of the counter capture channels can be used as a PWM output or to capture the timing of edges on input signals It can also be configured in IR generation mode where it counts timer 3 periods and the output is ANDed with the output of timer 3 to generate modulated consumer IR signals with minimal CPU interaction Timer 2 is a 40 bit timer used by the Bluetooth low energy stack It has a 16 bit counter with a configurable timer period and a 24 bit overflow counter that can be used to keep track of
17. ns can not be met for certain configurations or co location with another transmitter then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number can not be used on the final product In these circumstances the OEM integrator will be responsible for re evaluating the end product including the transmitter and obtaining a separate FCC and Industry Canada authorization End Product Labeling The BLE113 module is labeled with its own FCC ID and IC Certification Number If the FCC ID and IC Certification Number are not visible when the module is installed inside another device then the outside of the device into which the module is installed must also display a label referring to the enclosed module In that case the final end product must be labeled in a visible area with the following Contains Transmitter Module FCC ID QOQBLE113 Contains Transmitter Module IC 5123A BGTBLE113 Or Contains FCC ID QOQBT113 Contains IC 5123A BGTBLE113 The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change HF related parameters in the user manual of the end product 8 2 1 FCC et IC D claration d IC Ce dispositif est conforme aux normes RSS exemptes de licence d Industrie Canada Son fonctionnement est assujetti aux deux conditions suivantes 1 ce dispositif ne doit pas provoquer de perturbation
18. nsions top view APC Hero Bluegiga Technologies Oy 01480 226600 Page 16 of 30 sales apc hero co uk n 0 6 mm HK lt lt 15 73 0 1 Figure 9 Physical dimensions side view 2 00mm 5 35mm 0 50mm 0 80mm GN A deu s E aao mep paces AMA EHD awam emm ccc ee eus lt gt ac 0 550mm E 1 675mm A Figure 10 Recommended land pattern for BLE113 A APC Hero Bluegiga Technologies Oy 01480 226600 Page 17 of 30 sales apc hero co uk 4 Power On Reset and Brownout Detector BLE113 includes a power on reset POR providing correct initialization during device power on It also includes a brownout detector BOD operating on the regulated 1 8 V digital power supply only The BOD protects the memory contents during supply voltage variations which cause the regulated 1 8 V power to drop below the minimum level required by digital logic flash memory and SRAM When power is initially applied the POR and BOD hold the device in the reset state until the supply voltage rises above the power on reset and brownout voltages APC Hero Bluegiga Technologies Oy 01480 226600 Page 18 of 30 sales apc hero co uk 5 Design Guidelines 5 1 General Design Guidelines LE113 can be used directly with a coin cell battery Due to relatively high internal resistance of a coin cell battery it
19. o uk Page 30 of 30
20. pad size A low residue no clean solder paste should be used due to low mounted height of the component Celsius Figure 16 Reference reflow profile APC Hero Bluegiga Technologies Oy 01480 226600 Page 22 of 30 sales apc hero co uk 7 Block diagram BLE113 is based TI s CC2541 chip Embedded 32 MHz and 32 678 kHz crystals are used for clock generation Matched balun and low pass filter provide optimal radio performance with extremely low spurious emissions Small ceramic chip antenna gives good radiation efficiency even when the module is used in layouts with very limited space CC2540 Debug interface Power on reset 8051 CPU core and memory arbitrator Analog comparator IRQ controller Radio arbiter Radio registers Link layer engine SRAM J9j 041u09 0 1 Demodulator Modulator a mmm a Assembly EIC variant BLE112 A or USART 0 BLE112 E USART 1 Frequency Receive synthetisizer Transmit U FI connector TIMER 1 BLE112 F TIMER 2 TIMER3 Chip TIMER 4 antenna l l l l l l l l l l l l l l BLE112 A Balun LPF L Figure 17 Simplified block diagram of BLE113 CPU and Memory The 8051 CPU core is a single cycle 8051 compatible core It has three different memory access buses SFR DATA and CODE XDATA a debug interface and an
21. pedance path for the return current following the signal and supply traces all the way from start to the end A good practice is to dedicate one of the inner layers to a solid GND plane and one of the inner layers to supply voltage planes and traces and route all the signals on top and bottom layers of the PCB This arrangement will make sure that any return current follows the forward current as close as possible and any loops are minimized APC Hero Bluegiga Technologies Oy 01480 226600 Page 19 of 30 sales apc hero co uk Signals GND Power Signals Figure 12 Typical 4 layer PCB construction C 225 Overlapping GND layers without Overlapping GND layers with GND stitching vias GND stitching vias shielding the HF energy Figure 13 Use of stitching vias to avoid emissions from the edges of the PCB 5 3 BLE113 A Layout Guide For optimal performance of the antenna place the module at the corner of the PCB as shown in the figure 14 Do not place any metal traces components battery etc within the clearance area of the antenna Connect all the GND pins directly to a solid GND plane Place the GND vias as close to the GND pins as possible Use good layout practices to avoid any excessive noise coupling to signal lines or supply voltage lines Avoid placing plastic or any other dielectric material closer than 5 mm from the antenna Any dielectric closer than 5 mm from the antenna will detune the antenna to lower
22. powered directly from a standard 3V coin cell battery or pair of AAA batteries In lowest power sleep mode it consumes only 500nA and will wake up in few hundred microseconds KEY FEATURES e Bluetooth v 4 0 single mode compliant o Supports master and slave modes Up to eight connections e Integrated Bluetooth Smart stack o GAP GATT L2CAP and SMP o Bluetooth Smart profiles e Radio performance o TX power 0 dBm to 23 dBm o Receiver sensitivity 93 dBm e Ultra low current consumption o Transmit 18 2 mA OdBm o Transmit 14 3 mA OdBm DC DC o Receive 14 3 mA o Sleep mode 3 0 4 uA e Flexible peripheral interfaces o UART and SPI 126 PWM and GPIO o 12 bit ADC APPLICATIONS e Host interfaces o UART e Health and fitness sensors e Programmable 8051 processor for stand e Medical sensors alone operation e iPhone and iPad accessories e Dimensions 9 15 x 15 75 x 2 1 mm e Security and proximity tags e Bluetooth CE IC South Korea and e Key fobs Japan qualified e Smart home sensors and collectors e Wireless keys e HID keyboards and mice APC Hero 01480 226600 sales apc hero co uk Bluegiga Technologies Oy 1 BLE113 Product numbering Antenna A Internal V4 BLE113 A X Firmware revision Available products and product codes Product code Description BLE113 A v1 BLE113 with integrated chip antenna APC Hero 01480 226600 sales apc hero co uk Bluegig
23. res sur le transmetteur Cependant l int grateur est responsable des tests effectu s sur le produit final afin de se mettre en conformit avec d ventuelles exigences compl mentaires lorsque le module est install exemple missions provenant d appareils num riques exigences vis vis de p riph riques informatiques etc REMARQUE IMPORTANTE cas dinobservance de ces conditions en ce qui concerne certaines configurations ou l emplacement du dispositif proximit d un autre metteur les autorisations de FCC et d Industrie Canada ne seront plus consid r es valables et l identification de FCC et le num ro de certification d IC ne pourront pas tre utilis s sur le produit final Dans ces cas l int grateur OEM sera charg d valuer nouveau le produit final y compris l metteur et d obtenir une autorisation ind pendante de FCC et d Industrie Canada tiquetage du produit final Le module BLE113 est tiquet avec sa propre identification FCC et son propre num ro de certification IC Si identification FCC et le num ro de certification IC ne sont pas visibles lorsque le module est install a l int rieur d un autre dispositif la partie externe du dispositif dans lequel le module est install devra galement pr senter une tiquette faisant r f rence au module inclus Dans ce cas le produit final devra tre tiquet sur une zone visible avec les informations suivantes Contient module metteur ident
24. t be floating See the Profile Toolkit developer guide for more information about the configuration During reset the I O pins are configured as inputs with pull ups P1 0 and P1 1 are inputs but do not have pull up or pull down 2 2 UART UART baud rate can be configured up 2 Mbps See the Profile Toolkit developer guide for more information Following table lists commonly used baud rates for BLE113 Table 4 Commonly used baud rates for BLE113 APC Hero Bluegiga Technologies Oy 01480 226600 Page 10 of 30 sales apc hero co uk 2 3 Electrical Characteristics 2 4 Absolute Maximum Ratings Note These are absolute maximum ratings beyond which the module can be permanently damaged These are not maximum operating conditions The maximum recommended operating conditions are in the table 6 Raing Min Max Unt Storage Temperature Other Terminal Voltages VSS 0 4 VDD 0 4 supply nets must have the same voltage Table 5 Absolute Maximum Ratings 2 5 Recommended Operating Conditions Rating Unt AVDD DVDD Supply voltage noise should be less than 10mVpp Excessive noise at the supply voltage will reduce the RF performance Table 6 Recommended Operating Conditions 2 6 DC Characteristics EL m ____ 051 _ _ 25 Vv __ Logic 0 input current Inputequalsov 50 50 Logic 1 input current Inputequals VDD 50 50 nA
25. upport for CCM The ADC supports 7 to 12 bits of resolution with a corresponding range of bandwidths from 30 kHz to 4 KHz respectively DC and audio conversions with up to eight input channels I O controller pins are possible The inputs can be selected as single ended or differential The reference voltage can be internal AVDD or a single ended or differential external signal The ADC also has a temperature sensor input channel The ADC can automate the process of periodic sampling or conversion over a sequence of channels The C module provides a digital peripheral connection with two pins and supports both master and slave operation IC support is compliant with the NXP I2C specification version 2 1 and supports standard mode up to 100 kbps and fast mode up to 400 kbps In addition 7 bit device addressing modes are supported as well as master and slave modes The ultralow power analog comparator enables applications to wake up from PM2 or based on an analog signal Both inputs are brought out to pins the reference voltage must be provided externally The comparator output is connected to the I O controller interrupt detector and can be treated by the MCU as a regular I O pin interrupt RF front end HF front end includes combined matched balun and low pass filter and ceramic chip antenna with matching network Optimal matching combined with effective low pass filter provides extremely low in band spurious emissions and harmoni
Download Pdf Manuals
Related Search