User manual
Contents
1. The options menu allows configuring the appearance brightness or language of the Smart Touch among other things If the menu is unblocked administrator mode disabled any type of user will be able to change any configuration In this case use the bar at the top of the main window to slide down the menu It is possible to block this menu depending on the programming of the device so it can be only available for administrators If the menu is blocked administrator mode is enabled press in the centre of the main window for 5 seconds approximately and use the keyboard to enter the access password The options menu shows the following 6 submenus that are explained next KNX Touch screen 12 21 USER MANUAL O ingenium SMART TOUCH v1 1 www ingeniumsl com 2 4 1 TIME The Smart Touch can work as date and time slave in the KNX bus by receiving the corresponding data by telegrams from any other KNX clock see programming Error No se encuentra el origen de la referencia Error No se encuentra el origen de la referencia pag jError Marcador no definido The current date and time can also be configured manually with this option of the menu Set the desired values using the left and right arrows for every field as shown next Press the arrow on the left to go back to the main window without saving the date and time changes Press ok on the right to accept the new configuration By doing this the Smart Touc2. 2 2 6 SCENES Scene execution Scene icons allow executing programmed scenarios or moods this means a group of actions that are executed simultaneously for example switch off all the lights raise up all the shutters etc 2 2 LIST OF AVAILABLE ICONS The available functions could be different depending on the user s needs and the programming done Ask the programmer integrator of the home automation system for further information about the possibilities Icons in page Position Icon Name Function 1 2 3 E A O 7 KNX Touch screen 8 21 O a SENIUM o USER MANUAL SMART TOUCH v1 1 Page 2 Position Icon 7 Page 3 Position Icon Function 7 Page 4 Position Icon Z Function E eC Zz 5 7 KNX Touch screen 9 21 USER MANUAL O a SMART TOUCH v1 1 YW 2 3 INTERNAL THERMOSTAT The Smart Touch can incorporate an internal thermostat to measure and control the temperature of the room where it is installed If an internal thermostat is installed its current status is shown at a bottom bar of the main window and it is alternately displayed with the current time 2 3 1 SETPOINT AND ROOM TEMPERATURE Do click on the bottom bar or slide upwards to show the control dialogue of the internal thermostat From left to right side it is shown the working mode the measured temperature and the actual status on off of the internal thermostat A new set point
3. Touch screen Smart Touch v1 1 USER MANUAL ingenium Parque Tecnol gico de Asturias Parcela 50 33428 Llanera Asturias Spain Tel 34 985 118 859 Fax 34 984 283 560 ingeniumsl ingeniumsl com www ingeniumsl com TECHNICAL SUPPORT Tel 34 985 113 339 tecnico ingeniumsl com USER MANUAL SMART TOUCH v1 1 ingenium S 7 www ingeniumsl com 1 General description 2 2 Working mode 3 2 1 Introduction 3 2 2 Control icons 4 2 2 1 Lights 4 2 2 2 Dimmers 4 2 2 3 RGB Leds 5 2 2 4 Shutters Blinds 5 2 2 5 Thermostats 7 2 2 6 Scenes 8 2 2 7 List of available icons 8 2 3 Internal thermostat 10 2 3 1 Set point and room temperature 10 2 3 2 Switch on off 11 2 3 3 Working mode 11 2 3 4 Operation mode 11 2 4 Options menu 12 2 4 1 Time 13 2 4 2 Wi Fi 14 2 4 3 Appearance 15 2 4 4 Brightness 17 2 4 5 Security 18 2 4 6 Language 18 2 5 Default actions 19 2 5 1 Gesture control 19 2 5 2 List of available default actions 19 3 Notes 20 Touch screen 1 21 ingenium O Senium USER MANUAL SMART TOUCH v1 1 1 GENERAL DESCRIPTION The Smart Touch is a full colour capacitive 4 3 touch screen to control and monitor any KNX installation using 3D plans photographs friendly icons etc It allows to program up to 4 pages with 8 icons in each page with which to control lights shutters thermostats RGB leds executing scenes and control any other KNX installation devices bei
4. 1 2 2 3 RGB LEDS RGB lights control this icon represents the current colour of an RGB led light By clicking on the icon a control dialogue appears and allows selecting a colour from the palette and setting a brightness value by sliding the finger It is also indicated graphically as well as numerically the value from O to 255 of the brightness and colour intensities Press the ok button on the right to send a new colour and brightness setting Press the arrow at the bottom left to go back to the main window 2 2 4 SHUTTERS BLINDS Shutter Blind control this icon represents the current position of a shutter or blind KNX Touch screen 5 21 USER MANUAL O ias SMART TOUCH v1 1 YW 2 2 4 1 Shutter By clicking on the icon a control dialogue appears and allows setting a new position value by sliding the finger It is also indicated graphically as well as numerically the value in percentage of the current position ye A Press the arrow at the bottom left to go back to the main window 2 2 4 2 Blinds with lamellas When controlling blinds an angle icon appears above the position indicator to show the lamella function and opening close status The position of the lamellas is also represented by the width of the slats and can be changed by sliding the finger from left to right closing or right to left opening When the position of the lamellas change the vertical po
5. temperature can be stablished by sliding the finger over the circular scroll bar the command is sent when release KNX Touch screen 10 21 USER MANUAL O la SMART TOUCH v1 1 YW 2 3 2 SWITCH ON OFF The thermostat can be switched on and off by clicking over the following icon on the right When clicking the off button the switch off actions are executed the heating or cooling is switched off depending on the current status 2 3 3 WORKING MODE The working mode is changed just by clicking over the icon Summer mode when the set point temperature is lower than the measured one the thermostat will switch on the cooling system Winter mode when the set point temperature is higher than the measured one the thermostat will switch on the heating system Mix mode Summer and winter mode simultaneously 2 3 4 OPERATION MODE The current operation mode is indicated with the following icons at the bottom right corner Remote operation mode In this mode the user cannot change the set point temperature the working mode of the thermostat or switch it on off Local operation mode In this mode the user has complete control over all thermostat functions The operation mode of the Smart Touch internal thermostat is stablished by other devices of the home automation system and cannot be changed by clicking on the icon KNX Touch screen 11 21 USER MANUAL O as SMART TOUCH v1 1 Y 2 4 OPTIONS MENU
6. the Android app is called aSC and it is available in Google Play the OS app is called SC and it is available in the App Store See their corresponding manuals for further information KNX Touch screen 14 21 USER MANUAL S NSENUM NY SMART TOUCH v1 1 Y 2 4 3 APPEARANCE In this option menu the appearance of the screen icons and colours can be changed by selecting different themes according to the customer likes The Smart Touch incorporates 3 default themes predefined to change the appearance of the screen with different colours and icon styles but it can also incorporate another 3 themes that can be customized by programming ask the administrator of your home automation system 2 4 3 1 Change automatically The device can show a fixed theme or a list of themes that will change automatically by programmed hours to do so change the appearance mode to auto and select the time of the day to change The Smart Touch will show the programmed themes every day at the configured times for each one KNX Touch screen 15 21 USER MANUAL O ias SMART TOUCH v1 1 YW To select a theme to be included in the auto change sequence do click on the upper right corner of it Then write the desired hour of change with the keyboard by clicking over the clock at the bottom of each theme Click ok at the bottom right corner of the keyboard to accept the settings and go back to the main window saving ch
7. anges with the arrow button 2 4 3 2 Change by bus telegram The appearance can also be changed by bus telegrams from any other device of the home automation system see jError No se encuentra el origen de la referencia jError No se encuentra el origen de la referencia pag Error Marcador no definido KNX Touch screen 16 21 ingenium O s www ingeniumsl com USER MANUAL SMART TOUCH v1 1 2 4 4 BRIGHTNESS This option of the menu allows configuring the brightness behaviour of the screen backlight There are three parameters to configure that are explained next Active 3 15 Is the brightness level when the screen is being used Standby 0 15 Is the brightness level that it is set after a period of idle time Set this value to O to switch off the brightness completely when the Smart Touch is not being used Time 5 60 seconds Is the time that the screen waits to set the standby brightness level since the last pulsation Press the arrow on the left to go back to the main window without saving changes Press ok on the right to accept the new configuration Press the arrow on the left to go back to the main window without saving changes Press ok on the right to accept the new configuration KNX Touch screen 17 21 USER MANUAL O aaa SMART TOUCH v1 1 Y 2 4 5 SECURITY The Smart Touch can be locked with a 4 digits password to avoid its use Do click on the corresponding but
8. h will send the date and time to the other devices of the home automation system KNX Touch screen 13 21 ingenium O Senium USER MANUAL SMART TOUCH v1 1 2 4 2 WI FI The Smart Touch incorporates Wi Fi connectivity which allows the user to control the home automation system locally through any wireless device such as smartphones or tablets and also for the programmer to download the project It works as an access point creating a Wi Fi network that any PC smartphone or tablet can connect to and operate it with the Ingenium Android and iOS available applications The Wi Fi network is generated by the Smart Touch with the name SSID and password configured in this menu This network has no internet access so it is not possible to navigate through the web or control the home automation system from outside the house or installation AN The type of security of the network generated is WPA and the password must have at least 8 characters The Wi Fi access point creation can be disabled by pressing the on off button Press ok at the bottom right corner to accept every configuration setting and create a network Below the Wi Fi settings there is information about the IP of the Smart Touch and MAC address Press the arrow on the left to go back to the main window without saving changes Press ok on the right to accept the new configuration The control applications are free and can be found in the corresponding markets
9. ng ideal to work as a room controller It incorporates two user levels normal user and administrator and the appearance of the pictures menus and icons shown is completely customizable by the programmer with the programming software SIDEKNX that allows creating different themes The appearance theme can be also changed manually by the user or automatically by programmed hours General characteristics Admits up to 4 control pages background 3D plans photographs etc 8control icons per plan Scenes on off dimming shutter thermostats RGB Leds control Fully customizable themes icons background and menus appearance Wi Fi connectivity for programming and wireless local control via Android iOS applications Programmable automatic theme change by hour Two user level modes administrator and standard user KNX Touch screen 2 21 ingenium O Senium USER MANUAL SMART TOUCH v1 1 2 WORKING MODE 2 1 INTRODUCTION The Smart Touch interface is divided in three zones e A central zone where the user find the icons with which to control all the elements of the installation lights shutters thermostats etc It is possible to have up to 4 pages with 8 icons in each page e The internal thermostat control interface that it is shown by sliding upwards the main screen if the Smart Touch has an internal thermostat incorporated e Anoptions menu that it is shown by sliding downwards the main
10. rogrammer integrator of the home automation system for further information about the possibilities Control gesture Function s Slide upwards fe Slide downwards KNX Touch screen 19 21 IA USER MANUAL SMART TOUCH v1 1 3 NOTES KNX Touch screen 20 21 O 4 SCUM a Parque Tecnol gico de Asturias Parcela 50 33428 Llanera Asturias Spain Tel 34 985 118 859 Fax 34 984 283 560 ingeniums ingeniumsl com www ingeniumsl com ER 0584 2007 Liability limitation The present document is subject to changes or excepted errors The contents are continuously checked to be according to the hardware and software but deviations cannot be completely excluded Consequently any liability for this is not accepted Please inform us of any suggestion Every correction will be incorporated in new versions of this manual
11. screen In this menu can be configured the visual theme brightness Wi Fi language password etc Only an Administrator user can have access to the options menu You will find below a detailed explanation of each zone of this user interface KNX Touch screen 3 21 USER MANUAL O as SMART TOUCH v1 1 YW 2 2 CONTROL ICONS In the following section is explained each of the control functions that can be programmed in the Smart Touch The available functions could be different depending on the user s needs and the programming done Ask the programmer integrator of the home automation system for further information about the possibilities 2 2 1 LIGHTS Switch on off lighting this icon allows controlling the light of the corresponding room or zone simply by clicking on it The status of the light is permanently updated and the bulb will be either on or off according to it Lightning regulation this icon represents the current brightness level of a dimmering light 2 2 2 DIMMERS By clicking on the icon a control dialogue appears and allows to switch on off the light or setting a new brightness value by sliding the finger the command is sent when release It is also indicated graphically as well as numerically the value in percentage of the light intensity Press the arrow at the bottom left to go back to the main window KNX Touch screen 4 21 ingenium O Senium USER MANUAL SMART TOUCH v1
12. sition of the blind may change too according to received values KNX Touch screen 6 21 AM USER MANUAL SMART TOUCH v1 1 2 2 5 THERMOSTATS External thermostat control this icon allows controlling an external thermostat of the home automation installation By clicking on this icon a control dialogue appears and allows to switch on off the thermostat or setting a new set point temperature by sliding the finger over the circular scroll bar the command is sent when release The current measured temperature is also indicated at upper left corner from O to 51 C Use the icons below the set point scroll bar to set the working mode of the thermostat Working mode from left to right Summer mode when the set point temperature is lower than the measured one the thermostat will switch on the cooling system Winter mode when the set point temperature is higher than the measured one the thermostat will switch on the heating system Mix mode Summer and winter mode simultaneously KNX Touch screen 7 21 USER MANUAL O la SMART TOUCH v1 1 YW Operation mode from left to right Remote operation mode In this mode the user cannot change the set point temperature the working mode of the thermostat or switch it on off Local operation mode In this mode the user has complete control over all thermostat functions Press the arrow at the bottom left to go back to the main window
13. ton to enable or disable the lock of the screen the password is required for any change of this function The default password is 1234 and it can be changed by clicking on the corresponding button in the centre of the window If the lock mode is enabled the screen will ask for the password every time that changes from standby to active mode If the lock mode is disabled the Smart Touch can be activated and therefore used by anyone just by clicking on the screen 2 4 6 LANGUAGE Use this menu to change the presentation language of the Smart Touch Choose between English Spanish and French by clicking on the left and right arrows Press the arrow on the left to go back to the main window and accept changes KNX Touch screen 18 21 ingenium O Senium USER MANUAL SMART TOUCH v1 1 2 5 DEFAULT ACTIONS 2 5 1 GESTURE CONTROL The Smart Touch allows executing some programmed actions by gesture control When the screen is off or locked it is possible to execute some actions without needing to unlock it just sliding the finger upwards or downwards The available functions could be different depending on the user s needs and the programming done Ask the programmer integrator of the home automation system for further information about the possibilities 2 5 2 LIST OF AVAILABLE DEFAULT ACTIONS The available functions could be different depending on the user s needs and the programming done Ask the p
Download Pdf Manuals
Related Search