wireless DMX user Manual - wire
Contents
1. Mode of DMX 512 control Press MENU until it is 1 and the other digits are Press ENTER into DMX control mode In DMX control mode the other three numbers indicate the DMX address of the light Then press UP and DOWN to adjust the DMX address code NOTE When the decimal point on the LED display is off that is 7CH Mode When the decimal point on the LED display Page 3 is on that is 4CH Mode Press ENTER and DOWN at the same time to choose 7CH Mode or 4CH Model NOTE When the decimal point on the LED display is off that is 7CH Mode When the decimal point on the LED display is on that is 4CH Mode Press ENTER and DOWN at the same time to choose 7CH Mode or 4CH Mode 7 CH Mode 4 CH Mode MODE UP DOWN ENTER e DMX 7CH MODE CH1 General Dimmer 1 255 dimmer from dark to bright CH2 RED 1 255 dimmer from dark to bright CH3 GREEN 1 255 dimmer from dark to bright CH4 BLUE 1 255 dimmer from dark to bright CH5 AMBER 1 255 dimmer from dark to bright CH6 Strobe amp Color change color gradual change mode 0 49 All strobe the brightness of each color is adjustable 50 100 color change strobe the brightness of each color is adjustable 101 150 4 basic colors change the brightness 151 200 9 colors change the brightness of each color is adjustable 201 250 9 colors gradual change 251 255 mixed colors gradual change CH7 Stro2. The Foundation User Manual LED Battery Slim Par Fixture RGBA DMX 7Ch 4CH Il HI Security 1 2 Make sure the user voltage cannot higher or lower than the regulating voltage Please use proper and safe AC cord to connect the product use a plug to connect the cord to the power supply Don t drag the cord or pull the plug Make sure to shut off the power supply when stop using the light and before cleaning Make sure there is no combustible or explosive object around 0 5 meters Do not amend the light by unprofessional person It may cause short circuit combustion or electric shock etc and it is not in guarantee in this case Unpacking The light 1pc DMX cable Ipc Power cable 1pc Battery recharger 1pc User Manual 1pc Technical Parameters 2 PV ON EA a eran pa e AU A UN Light Source 186pcs of 10mm high light LED lamps Power supply methods 1 AC power 2 Battery Battery support time 5 hours Recharger 6 hrs red recharging blue finishing recharging Color Range 16 7 million RGB colors Beam Angle 30 degrees default LED life time 60 000 hours Battery life time 600 times recharge Dimmer 0 100 with regulated constant color control Power consumption 20W Control panel 4 Digital LED display figures Input voltage AC 220 240V 50Hz AC100 120V 60Hz Cover Aluminum die casting Maximum Ambient Temperature 45 C Product dimension L26 W11 2 H
3. or DOWN to choose the colors of strobe There can be 1 9 colors take part in strobe When it is 6010 means all colors on for strobe 7 Mode of choosing how many colors for Color Change Press MENU until it is 7 and the other digits are Press ENTER into this mode Press UP or DOWN to choose number for how many colors that take part in Color Change There are 2 9 colors optional 8 Mode of choosing how many colors for Gradual Color change Press MENU until it is 8 and the other digits are Press ENTER into this mode Press UP or DOWN to choose how many colors take part in for Gradual Color Change There are 1 9 colors optional When it is 8010 it is mixed colors Gradual Color Change Page 5 10 10 9 Mode of speed for Strobe Color Change Gradual Color Change 1 From 6 switch to 9 adjusting the speed of strobe 2 From 7 switch to 9 adjusting the speed of Color Changing 3 From 8 switch to 9 adjusting the speed of Gradual color change Press MENU until it is 9 and the other digits are Press ENTER into the mode Then press UP or DOWN to adjust the speed of Strobe Color Change Gradual Color Change the more value the faster the speed 11 C Color Picker Button NO Color DM
4. 22 5 CM N W 2 5 KGS Page 2 IV Brief Introduction There are four LED tubes digital figures on the back panel of the light The functions are MENU UP DOWN ENTER as below MODE UP DOWN ENTER There are total 11 modes for control The control mode is displayed by the first number When you press MENU the number will increase one gradually from 0 to 9 in circle Enter into the mode to adjust the effect you need 1 O Mode of Sound Activation 2 1 Mode of DMX 512 Control 3 2 Mode of adjusting brightness of red 4 3 Mode of adjusting brightness of green 5 4 Mode of adjusting brightness of blue 6 5 Mode of adjusting brightness of amber 7 6 Mode of choosing colors for strobe 8 7 Mode of choosing how many colors for color change 9 8 Mode of choosing how many colors for Gradual Color Change 10 9 Mode of speed for strobe Color Change Gradual Color Change 11 C Color Picker 12 Master slave control mode V Introduction of Using 1 0 Mode of Sound Activation Press MENU until it is 0 and the other digits are Press ENTER to sound activity mode In sound activity mode the other three numbers mean the sound activity s sensitivity Press UP or DOWN to adjust the sensitivity The smaller number it is the more sensitive it will be 2 1
5. X Value C C000 No Light C001 RGBA All 100 C002 R C003 G C004 B C005 A C006 RG C007 RB C008 RA C009 GB C010 GA C011 BA C012 RGB C013 RGA C014 GBA C015 RBA 12 Master Slave Control Mode Connect all the lights with DMX signal cables Choose one as the master light the others as slaver lights Set all the slaver lights to 1001 Operate the master light so all the slavers do the same as the master NOTE There should be only one master light in one circuit line The slaver lights should be under DMX 7CH mode not DMX 4CH mode Page 6 Declaration Under the mode of master slave the synchronic effect is not as good as under the DMX mod Especially for gradual color change the master will always be a little more advanced than the slavers 13 Saving Function After adjusting the state that you like press ENTER and UP at the same time so that the present state will be saved The saved state is the state power on next time NOTE The MODE 9 cannot be saved 14 Recharger When recharging the red light indicator on the charger is on When the battery is fully charged it stops recharging and the blue indicator turns on Recharging time is around 6 hours VII Wireless Control Introduction of wireless control board Dy Bo oie Interface LED Indicator ID Adjusting Button Hole for Fixation Antenna Antenna Receiver Wireless Control Board Characteristics Name 2 4G wire
6. be color changing colors gradually changing speed adjustable 1 255 from slow to fast Page 4 e DMX 4CH MODE CH 1 RED 1 255 dimmer from dark to bright CH2 GREEN 1 255 dimmer from dark to bright CH3 BLUE 1 255 dimmer from dark to bright CH4 AMBER 1 255 dimmer from dark to bright 2 Mode of adjusting brightness of red Press MENU until it is 2 and the other digits are Press ENTER into adjusting the brightness of red Then press UP or DOWN to adjust the color of green 3 Mode of adjusting brightness of green Press MENU until it is 3 and the other digits are Press ENTER into adjusting the brightness of red Then press UP or DOWN to adjust the color green 4 Mode of adjusting brightness of blue Press MENU until it is 4 and the other digits are Press ENTER into adjusting the brightness of red Then press UP or DOWN to adjust the color of blue 5 Mode of adjusting brightness of amber Press MENU until it is 5 and the other digits are Press ENTER into adjusting the brightness of red Then press UP or DOWN to adjust the color amber 6 Mode of choosing the kinds of different colors for strobe Press MENU until it is 6 and the other digits are Press ENTER into the mode Press UP
7. ers If more than 1 wireless network is being used in the same place each network ID should be different d Operation of lights is controlled through DMX desk controller After the transmitter receives the DMX data from the desk ti will choose and interference free frequency to send data When the red LED on the receiver flashes the receiver searches the frequency upward until it receives the correct frequency At that moment the green indicator will begin to flash The faster the DMX data transfers the faster the indicator flashes e The communication is set up successfully The wireless receiver is compatible with the following controllers a DMX 1314 ID 1 7 b DMX 1315 ID 0 15 c DMX 1316 ID 1 7 Page 8 VIII Technical Parameters Light Source 186pcs F 10mm RGBA LED a 45R 47G 47B 47A Color Range 16 7 million additive RGBA colors continuously variable intensity 256x256x256 16777216 Beam Angel 30 Control Panel Digital lifetime 60 000 hours Dimming 0 100 with regulated constant color control Strobe 10 Flashes per second any color Power Supply 35W Operation Mode DMX 512 Manual Sound Internal Program DMX Control 7 4 CH Battery Input Voltage AC90 240V 50 60HX Power Switch Auto Change Housing Aluminum Alloy Black White Maximum Ambient Temperature 40 C Page 9
8. less DMX transmit and receive board Compact in size suitable to install inside the fixture Single button operation tri color LED display Transfer standard DMX data also can transfer the data among the network lights Select for inference free frequency automatically 126 frequency range ensure reliability in communication 7 Groups of ID are selectable The user has 7 groups of wireless network without interference in the same place Input voltage DC 5V Working frequency 2 4G ISM 126 frequency range Max sending power 20dBm Receiving sensibility 94dBM Signal interface RS485 or CPU serial port AURT Page 7 Operation Introduction 1 A 7 ID Number and LED indicator synopsis a Red b Green c Yellow d Blue e Purple f Cyan g White Press the button once it will show the present ID Press once more and the ID will increase by one Working state from the LED indicator a Retains on no DMX or no wireless signal b Red flash sending signal c Green flash receiving signal Signal Frequency 2 400 2 525G total 126 frequency range selected automatically ID Setting 1 7 press KEY to adjust only the identical ID number can communicate Setting up communication a Connect the transmitter with the DMX desk controller b Turn receiving power to ON on the transmitter NOTE The receiver turns on when the light is powered on c Set the same ID on the transmitter as the receiv
Download Pdf Manuals
Related Search