Product Manual 1.4 MB - Rhin-O-Tuff
Contents
1. If machine cycles on its own turn off power switch unplug machine from the wall outlet and call your dealer immediately for service 4 Turn power switch off before maintaining or changing die assembly Crush hazard Keep hands away from moving parts Lockout and disconnect Use of appropriate hand protection should be utilized to avoid injury from handling of materials Cutting Hazard Injury to fingers and hands Use hand protection Follow all recommended workplace procedures for repetitive activities Placing your machine in the proper location Before lifting machine turn power off and remove the power cord from the wall outlet AET The machine is very heavy Never attempt to lift m a eal the machine by yourself Two people will be Deer A needed to lift the machine Place the machine on a hard level surface place the foot pedal on the floor in front of the machine Ensure the placement of machine allows for ergonomic work flow separate locations for un punched books and punched books Connect the foot pedal into the foot pedal receptacle on the back of the machine do not M cs attempt to connect foot pedal into anything other ecu rol than the foot pedal receptacle eter Optional paper activated switches are available for these punches These switches replace the foot p into the foot pedal receptacle on the back of the mach Attach Handle to OD4800 e The OD4800 manual2. Instruction Book for the OD4012 OD4000 and OD4800 OD4012 OD4000 and OD4800 setup amp Operator Manual Issue 3 June 09 Performance Design LLC These punches have been designed to punch most any job that may pass through your office No matter what type of binding you need to carry out these punches can handle the job The maximum single punching length for the OD4012 OD4000 and OD4800 is a 11 297mm format The OD4012 and the OD4000 are electrically operated punches and the OD4800 is manually operated All three machines utilize a simple two knob die lock system to retain the die punch assemblies OD4000 OD4800 OD4012 Contents S N Punch 1 ___Instruction Book 1 __O l 1 ____ Brush 1 ___ Foot Pedal 1 ____ Power Cord 1 Reversing Tool 1 Inspected by OD4000 Contents S N Punch 1 Instruction Book 1 ____Knob Kit 1 Oil 1 a Y 20 x 1 2 Knob 2 Brush 1 ____ Foot Pedal 1 Power Cord 1 Inspected by OD4800 Contents S N Punch 1 ___Instruction Book 1 Knob Kit 1 ____ Handle with bolt 1 a 20 x 1 1 2 Knob 2 Oil 1 Brush 1 Inspected by Table of Contents Topic Safety Alert Symbols Safe operating guidelines Proper machine placement Attach OD4800 Handle Providing electric power Die installation Maintenance setting the paper stop guide Punching paper Removing paper waste Paper jam Troubleshooting Page Number 7 9 10 10 1
3. apARStABlies Aligning the paper stop with these marks will result in the punch pattern being centered on the paper and need only small adjustments if Punching Paper e Select an appropriate number of sheets to be punched and slide the sheets down vertically into the opening of the die assembly When the paper is fully inserted slide it to the left so it comes in contact with the paper stop Make sure all the edges of the sheets are flush by tapping the top and the right hand sides of the sheets then activate the punch by depressing the foot pedal OD4800 users pull handle toward front of machine If a paper activated switch is being used tap the sheets flush int before sliding the paper to the paper stop Removing Paper Waste The paper waste drawer is located conveniently on the front of the punch The paper waste drawer is removed by lifting up on the front and pulling out away from the machine This drawer should be checked frequently while punching and emptied as necessary 10 Paper Jam It is easier to remove one or two sheets at a time from the it backside of the material in the punch The OD4012 and OD4000 punches use a circuit board for controlling the punch cycle this circuit board also has the ability to automatically reverse the pusher bar and punch pins to their starting position if the machine takes too much time to complete a punch cycle This condition could happen if too much material has been attem
4. cycle 3 Foot pedal is not plugged into 3 Make sure foot pedal cable is machine attached to machine 4 Die lock handle is not locked 4 Lock the die lock handle 5 Reversing tool is in machine 5 Remove reversing tool and store properly 1 Pin retainer interference 1 Make sure pin retainer enters slot Die does not go into machine 2 Punch is stopped in mid cycle in pusher bar 3 Die lock handle is in lock position 2 Restart machine by turning power off and back on 3 Move handle to unlock position A NOTICE The 0D4012 and OD4000 have been tested with a duty cycle of 25 cycles per minute with a 1 minute rest period after 2 minutes of run time Operating outside of these limits could result in machine damage The OD4012 has earned the UL Listing Mark E179574 13 A IMPORTANT Be sure to fill out and return your Product Warranty Registration Card or Register online at www Rhin O Tuff com warranty_registration asp TUFF Part Number 001172 Rev 3 Aug 2010
5. 0 11 12 13 safety Alert Symbols e Make sure you read this section very carefully Learn to recognize these Safety Alert Symbols The OD4012 OD4000 and OD4800 have been designed to provide a high level of protection to an operator Follow the guidelines below while installing operating and maintaining your machine A CAUTION CAUTION Indicates a hazardous situation which if not avoided could result in minor or moderate injury It may also be used without the safety alert symbol as an alternative to Notice WARNING Indicates a hazardous situation which if not avoided could result in death or serious injury NDIN GSR DANGER Indicates a hazardous situation which if not avoided will result in death or serious injury This signal word is to be limited to the most extreme situations A Trip Hazard AN Electric Shock y A lt gt Two Person LIft Bost Hazard Hint or Suggestion wnt Cutting Hazard safe Operating Guidelines Always keep this instruction manual with the machine for reference to safe operating guidelines and correct operation of the machine The OD4012 and OD4000 need to be plugged into a wall outlet that provides a 15 amp 120 volt service 16 amp 220 volt for European installations and is protected by a fuse or circuit breaker at the main electrical panel Always replace any fuse with the same type and Hazardous voltage amperage fuse as indicated on the machine Fe E before servicing
6. er Crush hazard Keep hands away cord from the wall Locate the silver plug from moving parts on the rear of the left side panel of the pi si machine Remove the silver plug by prying it out gently with a small flat tool Insert the end of a large flat blade screwdriver into the open hole and engage with the end of the motor shaft Rotate the screwdriver counterclockwise 5 10 revolutions until the punch pins have been retracted back to the starting position Remove most or all of the material from the punch Remove the screwdriver from the punch and replace the small silvom gt sicg9 9 the power cord back into the wall outlet and turn the Test cycle the machine by punching with no material n O machine will reset itself back to its home position amount of material being punched and continue work It is easier to remove one or two sheets at a time from the Y backside of the material in the punch DANGER Only qualified personnel should attempt to Hazardous voltage work on this equipment There are no user nside serviceable parts inside of the machine before servicing Your machine has been designed for years of trouble free operation The following is a troubleshooting guide to help you through some of the problems that may be encountered Troubleshooting Symptom __ _ Possible Cause 1 Machine is off 1 Check power switch 2 Machine is not plugged in 2 Check both ends of power cord Machine does not
7. he adjustor bar to the right for shallower settings commonly used for thinner sized books Removing Punch Pins e Turn machine power off and remove die assemb e On the opposite side of the die assembly from th e Pull the pin capture away from the pin retainer to expose the punch pins 7 o Remove the desired punch pin or pins E Replace the pin capture by pressing down on the pin retainer and placing the pin capture back into place Install die assembly into machine as described earlier and turn machine power back on Die Maintenance e Die maintenance should be performed with the die removed from the machine To perform the die maintenance remove the die assembly from the machine see die installation section Apply enough oil to lightly coat each pin e Remove any excess oil with a disposable cloth After oiling always punch some scrap paper to remove excess oil Saturate a small section of ac portion of the cloth wipe the p iht of oil 4 Setting the paper stop guide OD4012 OD4000 and OD4800 e Locate the paper stop on the front cover of thtst 997 7mesamags tin knob counterclockwise so that the guide Shee RTT the right Move the paper stop until the desir huul SEE Mihi ie iii and tighten the knob clockwise until tight to m place Repeat this procedure until the punch the paper The OD4012 OD4000 and OD4800 punch maori ES the common size paper position markings on the F
8. pted to be punched at one time If this condition occurs allow the machine to attempt to reset itself back to its home position Turn the machine power switch off and remove some or all of the material in the Crush hazard Keep hands away pu n ch from moving parts Lockout and disconnect power before servicing lf the punch does not reset itself back to its home position the punch will need to be reversed manually OD4012 Manual Reverse utilizes a reversing tool supplied with the punch Turn the Crush hazard machine power switch off and unplu the power cord from the wall Locate the silver plug on the rear of the left side panel of the machine Remove the silver plug by prying it out gently with a small flat tool Insert the end of the reversing tool into the open hole and engage the tool with the end of the motor shaft Rotate the tool counterclockwise 5 10 revolutions until the punch pins have been retracted back to the starting position Remove most or all of the material from the punch Remove the reversing tool from the punch and replace the small silver plug Plug the power cord back inta the wall outlet and turn the power switch on Test cycle th jm punching with no material in the punch the machine w back to its home position Reduce the amount of matey punched and continue working Keep hands away from moving parts 11 OD4000 Manual Reverse Turn the machine ower switch off and unplug the pow
9. punch is shipped with the handle removed from the punch You will need two 3 8 wrenches not supplied to tighten the handle bolt Locate the handle and remove the nut washer and bolt from the handle Orientate the handle so the black handle grip extends to the right of the machine as seen on front cover of this book Slide handle onto exposed crankshaft of machine and align the holes in the handle with the hole in the crankshaft Insert the bolt completely through the handle and install the washer and nylock nut See photo below left Tighten the nut securely so there is not play between the handle and the crankshaft Open the top grey lid of the punch and remove the styrofoam block see photo below right Crankshaft Handle ach Remove Styrofoam Diagram 1 Image of OD4800 Providing power to the machine DANGER Power cord shall be certified for the country E E where the machine will be installed Plug one Uepenlyaapreved end of the power cord into the power cord Lee receptacle on the back of the machine The other end goes into the wall outlet Die Installation OD4012 Diagram 2 Make sure the machine is turned off before installing the die Crush hazard e Make sure there is no paper dust or paper chips soe ie aad in the machine die slot before installing the die power belone sn e Install the die by sliding it into the opening located on the left hand side of the machine Make s
10. ure the punch pin retainer slides into the slot on the backside of the opening e Install die until right side of die is flush to exterior of right side of machine Thread both retained die lock knobs into the die and tighten evenly until the die can not move Die Lock Knob T Diagram 2 Image of 0D4012 e OD4000 0D4800 Diagram 3 Make sure the machine is turned off before installing the Crush hazard d ie Keep hands away m from moving parts e Make sure there is no paper dust or paper chips a in the machine die slot before installing the die e Install the die by sliding it into the opening of the machine located on the left hand side of the machine Make sure the punch pin retainer slides into the slot of the pusher bar e Install die until right side of die is flush to exterior of right side of machine e Locate the two supplied die lock knobs and insert them into the left and right sides of the machine Thread both die lock knobs into die assembly and tighten evenly until die assembly can not move aS ee ae fr E sf Q Punch Pin Retainer oe LA a n W Die Lock Knob Diagram 3 Image of OD4000 Comb Die Backspace Margin Adjustment e The comb die assemblies for the OD4012 OD4000 and OD4800 have a four position adjustable backspace The positions are changed by pulling the adjustor bar to the left for deeper settings commonly used for average to thicker sized books and pushing t
Download Pdf Manuals
Related Search