PM-60A Instruction Manual
Contents
1. 2008 05 06 15 54 55 2008 05 06 15 54 54 Model 4 3 2 TrendTable The detailed information of the key as following Max The maximum of the Parameter data in the logical range Min The minimum of the Parameter data in the logical range Ave The average of the Parameter data in the logical range 4 3 3 TrendGraph Interface TrendGraph Interface showed as followed Trend Graph Model 4 3 3 TrendGraph 4 3 3 1 Click one point on the screen to descry the parameter value of Spo2 and PR at a certain time 4 3 3 2 TrendGraph can analysis the data It does some basis statistical analysis as well as SpO2 and pulse events analysis 10 SpO2 desaturation event is defined as drop in SpO2 by at least N for a minimum duration of L seconds N and L are configurable and is defaulted to 4 and 10 Pulse event is defined as change in pulse rate by at least N bpm beats per minute for a minimum duration of L seconds N and L are configurable and defaulted to 6 and 8 You can set the analysis parameters in the System Setup Menu 4 3 4 AlarmReview and WaveReivew Interface AlarmReview and WaveReivew Interface showed as followed AlarmReview WaveReview Model 4 3 4 AlarmReview and WaveReivew In the AlarmReview waveform display district waveform displays 8 seconds which 4 seconds are before a certain time when the alarm is turned on and 4 seconds are after appointed time when the alarm is turned on Th2. Make sure that the batteries meet the performance requirements Make sure that the pulse oximeter is in good working condition In case of any damage or abnormity do not use the pulse oximeter Contact your hospital s biomedical engineers or your service personnel immediately 5 2 Cleaning Your equipment should be cleaned on a regular basis If there is heavy pollution or lots of dust and sand in your place the equipment should be cleaned more frequently Before cleaning the equipment consult your hospital s regulations for cleaning the equipment Recommended cleaning agents are Mild soap diluted Ammonia diluted Sodium hypochlorite bleach diluted Hydrogen peroxide 3 Ethanol 70 Isopropanol 70 To clean your equipment follow these rules 1 Shut down the pulse oximeter and disconnect it from the power line 2 Clean the display screen using a soft clean cloth dampened with a glass cleaner 3 Clean the exterior surface of the equipment using a soft cloth dampened with the cleaner 4 Wipe off all the cleaning solution with a dry cloth after cleaning if necessary 5 Dry your equipment in a ventilated cool place 5 3 Disinfecting Disinfection may cause damage to the equipment and is therefore not recommended for this pulse oximeter unless otherwise indicated in your hospital s servicing schedule Clean the pulse oximeter before disinfecting it The recommended disinfectants include ethanol 70 isopropanol 7
3. 0 glutaraldehyde type 2 liquid disinfectants CAUTION Never use EtO or formaldehyde for disinfection 5 4 Disposal Dispose of the pulse oximeter in accordance with local environment and waste disposal regulations For the disposal of SpO2 sensor follow local regulations regarding disposal of hospital waste 6 Appendix 6 1 Alarm Characters Specification Finger Out SPO2 Sensor OFF Battery Too Low SPO2 Too High SPO2 Too Low PR Too High PR Too Low 6 2 Usual Metrical Range SPO2 1 99 PR 1 250
4. 17 1 Preface This manual contains the instructions necessary to operate the product safely and in accordance with its function and intended use Observance of this manual is a prerequisite for proper product performance and correct operation and ensures patient and operator safety This manual is based on the maximum configuration and therefore some contents may not apply to your product If you have any question please contact us This manual is an integral part of the product It should always be kept close to the equipment so that it can be obtained conveniently when needed This specification includes all the functions and operation flow some usual questions and detailed answers offered Please read the specification carefully before using this product to smooth your usage Thanks for using PM 60A Pulse Oximeter products and look forward to your valuable suggestions and advice PM 60A Website http www contecmed com cn 1 1 Caution Before usage please be aware of safety and validity stated below The system should be used under doctors guide The reliability of the product depends on whether the operation and maintenance are properly done amp Warning system errors may arise if non proper accessories are replaced therefore any maintenance men who haven t been trained in our company or normal maintenance organization should not maintain this system 1 2 Manipulator Obligation A Caution please read the us
5. CONTEC PM 60A Pulse Oximeter Users Manual CONTEC The document including some secret information belongs to Contec medical systems co LTD in which any information is not allowed to be transmitted copied or disclosed to any other companies except the recipient ones even not for other commercial purposes Catalogue Catalogue e tue ESE FIR NEC E aan eo eee SE CIR Cae TUR TRETEN EE SRARERNUEERIS 2 MEG DC 3 I 1 Caution Proceeding eve ol kel een heel ed REV PU er E sane ele ds 3 1 2 Manipulator Obligation 0 ccc cece e EEE E e 3 C M 2X Introd ctions tot etta fut tamea tame tontos 3 2 1 1 Intended Use icit ttti ti Sitiet entiende edente deti 4 2 1 2 Contraiidicatioris i niti tote nr etit t Ms s ag eel bal aoe o 4 2 1 3 COnmponents oot tesce ddr tese heec Er E Ere v den 4 yg IM etic e e a eared on dis A wang N Meg ohee To oaeed 4 3 Main Technical Index ccccccccccceccececcccccccccccsccsccecececccscssccccccccsseccescccessesee 3 1 Performance Specifications 0 cece ence eee eee een eese he ee essen senes 4 3 2 Technical specifications i iii eese ie pepe Dr ee el ode guo ghd oae tee eee eh o gap ee deg 5 SIME 6 4 Function Instr ctlong accceesecsseseeu ees ev eae ep Ea PAR bEE PEN GEN SER SEE E EYR EAR OE FEE Ea sa Uo eo aestu suenan 4 Main intertace sees de than edat umet an ete io ete aise ud 6 4 1 1 Com
6. ed on A indicates that alarm sounds are turned off SpO2 Area PR Area Physiological Alarm Area This area shows the physiological alarm message When multiple messages come they will be displayed circularly 10 Physiological Alarm Status Area Click the D button to pause or reactivate the alarm sound p BN indicates that alarm sounds are paused 11 Waveform Area This area displays SPO2 real time waveform 12 Function button Area 4 1 2 Function button Functions as follows Enter the new patient case history menu Patient s case history should be set up and stored 10 000 at best Enter the data review menu Review the monitoring data of the current patient or the patients who had been stored previously Enter the system setup menu Amend the system setup Press this button to make that alarm sounds are turned off The sounds of the heart murmur still are turned on Press this button to return to the main menu 4 0 New Patient Information Interface Click the New button of the main interface to enter the New patient case history interface New Patient information interface showed as followed New Patent Weight Model 4 2 1 New Patient Users can set up and store the personal information of the patient monitoring currently After the patient information is stored it will return to the main menu The EZ button change into the J Save G button Then click the but
7. er manual carefully before usage Obligations of Contec Medical System Co LTD 1 Our company will resolve any software and hardware problems of the product in one year after your purchase with the precondition of proper usage of it 2 Responsible for users training 3 Responsible for free update and life maintenance of the software 4 Responsible for free maintenance of hardware after your purchase 5 Not responsible for damage caused by improper usage or non fixed accessories usage 2 The Basics 2 1 Introduction 2 1 1 Intended Use The pulse oximeter is intended for continuously monitoring spot checking displaying storing and printing oxygen saturation and pulse rate of single adult pediatric and neonatal patient in hospital emergency treatment and patient transport as well as in home care environment WARNING This pulse oximeter is intended for use only by clinical professionals or under their guidance It must only be used by persons who have received adequate training in its use Anyone unauthorized or untrained must not perform any operation on it 2 1 2 Contraindications None 2 1 3 Components This pulse oximeter consists of a main unit and a SpO2 sensor 2 2 Features Regular Check Mode and Continuous Monitoring Mode Data Graph and Trend Table Review Rich Analysis report Perfect mount solution Sync with PC based Sofrware WinXP and WinVista 3 Main Technical Index 3 1 Performance Specificat
8. ions Display Resolution Display Mode Indicator Interface Power Supply Battery Trend Graph Table 3 5 Color TFT 320 x 240 Standard face Waveform face Display Direction adjustable Power indicator light Alarm sound Pluse tone One dual purpose socket for connecting SPO2 sensors and communication cables DC 5V lt 300MA Builtin Li Polymer 6 hours for charging 9 hours for continous working 12 hours for standby mode 3 7v 1900mah Resolution from 1s 5s 10s 30s 1min and so on Storage of latest 96 hours trend data Second is the unit History Storage of latest 10000 case history by SD card Permit to review momentarily Alarm Ajustable High and Low limits Three level audible and visual alarm latest 50 alarm information and waveform displays 8 seconds which 4 seconds are before a certain time when the alarm is turned on and 4 seconds are after appointed time when the alarm is turned on Wave Storage of 24 hours waveform and only the real time stored patients have waveform 3 2 Technical specifications Safety Meet the requirment of IEC60601 series Type of Protection Class II with internal electirc power supply Degree of Protection BF Dimention and Weight Dimention 92 W x82 H x22 D mm Weight 136g with battery Operation Environment Temperature 0 C 40 C Humidity 15 95 Storage Environment Temperature 20 C 60 C Humidity 10 95 Patient Range Neonate Pedia
9. is alarm symbol includes following items E do low level alarm Xx mid level alarm x x x high level alarm The waveform be displayed 16 seconds every screen in the WaveReview waveform display district 4 4 Setup Interface 4 4 1 Set up Interface Click the EA button of the main interface to enter the Setup interface 11 Setup interface showed as followed Instruction Model Setup Monitoring setting and producer setting Options as follows Item Purpose Producer Choosing scope setting Spo2 ALM Turn on off Spo2 alarm OFF OFF ON Spo2 ALM LVL Spo2 alarm level MID LOW MID HIGH Spo2 ALM HI Spo2 alarm high level 99 0 100 Spo2 ALM LO Spo2 alarm low level 80 PRALM Turn on off PR alarm OFF OFF ON PRALMLVL PR alarm level MID LOW MID HIGH PRALM HI PR alarm high level 110 0 300 PRALM LO PR alarm low level 50 Alarm Pause Alarm Pause Time 1MIN 1Min 2Min 3Min Always Display Display mode Model Model Mode2 System Time Set system time System Setup Enter system setup menu Pulse Sound Turn on off pulse sound OFF ON Demo Enter Demo mode NOTICE If the time is changed users should restart the apparatus by hand to ensure the accuracy of the data storage time 4 4 2 System Setup Click the a System Setup button of the Setup menu to enter the System Setup menu interface System Setup menu interface showed as f
10. of dust and dirt To avoid damage to the equipment follow these rules Always dilute according the manufacturer s instructions or use lowest possible concentration Do not immerse part of the equipment into liquid Do not pour liquid onto the equipment or accessories Do not allow liquid to enter the case Never use abrasive materials such as steel wool or silver polish or erosive cleaners such as acetone or acetone based cleaners WARNING Besure to shut down the system and disconnect all power cables from the outlets before cleaning the equipment CAUTION If you spill liquid on the equipment or accessories contact us or your service personnel NOTE To clean or disinfect reusable accessories refer to the instructions 14 delivered with the accessories 5 1 Safety Checks Before every use or after your pulse oximeter has been used for 6 to 12 months or whenever your pulse oximeter is repaired or upgraded a thorough inspection should be performed by qualified service personnel to ensure the reliability Follow these guidelines when inspecting the equipment Make sure that the environment and power supply meet the requirements Inspect the equipment and its accessories for mechanical damage Inspect all power cords for damage and make sure that their insulation is in good condition Make sure that only specified accessories are applied Inspect if the alarm system functions correctly
11. ollowed System Setup Minimum 5 Event Duratiol Model 4 4 2 System Setup 4 4 2 1 Users can set system sounds and overtime of the backdrop lighting 4 4 2 2 SpO2 Parameters Drop for Event value in to qualify as an SpO2 Desaturation Event Minimum Event Duration sec value in seconds of SpO2 decrease that qualifies as an SpO2 desaturation event Desaturation Criteria Level value in below which the SpO2 level must drop to be classified in a special category of statistics This threshold is indicated on the SpO2 graph by a red dotted line Pulse Rate Parameters Rate Change For Event bpm value in beats per minute to qualify as a pulse rate event Minimum Event Duration sec value in seconds of pulse rate change to qualify as a pulse rate event 4 4 2 3 Click OK to set new analysis parameters or click Cancel to leave them unchanged All setting will turn back to manufacture s setting when Click AH 5 Maintenance and Cleaning Use only the substances approved by us and methods listed in this chapter to clean or disinfect your equipment Warranty does not cover damage caused by unapproved substances or methods We make no claims regarding the efficacy of the listed chemicals or methods as a means for controlling infection For the method to control infection consult your hospital s Infection Control Officer or Epidemiologist Keep you equipment and accessories free
12. posing parts 2 dere e hr E ae ae ERR e eee Rat 7 41 2 Function Button eise E RI PS RR aver e E PIN ATE 8 4 2 New patient information interface 0 cece cece eee n cence nee eene ese hene nen 8 4 3 Data Review Interface 00 ce cccc cece aE e ence ARERR E AEE EAE ELEAN 9 4 3 1 Data Review Interface 0 cece cece cece cence cent mee ene emen 9 4 3 2 TrendTable Interface csse me e m emere 10 4 3 3 TrendGrape Interface de ee pe ped Ede Er Desa 10 4 3 4 AlarmReview and WaveReview Interface ccccceceneeeeeec teens eaenees 11 4 4 Setup Interfaces 72 ims ore a eher weds en ri Seed ede T 11 4A Setup Interface jis veces fenced oer eto eter e pr D M andes DR ERU 11 4 4 2 System Setup ii 4 se e eI E Gab ae ert eR e Re deuce ea aes 13 5 Maintenance and Cleaning ccccccccccccscccccccccccscecccccccccscccccccccccscsccccscscssceeel 4 5 1 Safety Checks RHET 15 532 Cleanin Sst iie t E I a rie danteqe auteirure iet d usienis 15 5 3 Disinfectig iu sc eto E A RR UR EI ERE ERA UAE LEVER E ER ORTI a 16 SPA DISPOSAL asf otis ene etes stu ee ot obses eoe eee datu telo eM ebat eia aed tae 16 6 Appendix e eee eee eee eee eee eee eese oe oeten e se ses ese oeoe osos sese esses eceses ooo osseseseseesessese 7 6 1 Alarm characters specification c cece eee e cece ence cence eee ee eee e he he nennen 17 6 2 Usual metrical ranges s istic ive e ex ee rea et eer Peu AR AE Cane eh Save
13. ton can store the personal information of the patient monitoring currently into the SD card 4 3 Data Review Interface 4 3 1 Data Review Interface Click the E Review J button of the main interface to enter the patient data review interface Data review interface showed as followed Data Review TrendT able 5 16 2009 9 10 40 41 AM Model 4 3 1 Data Review Users can review the monitoring data of the current patient or the patients who had been stored previously by selecting Patient ID Review includes 4 kinds TrendTable TrendGraph AlarmReview WaveReview as followed AlarmReview Trend T able d Notice the Wave Review function only be applicable for the patients monitoring currently and not be applicable for the patients monitoring previously By click Show Stat Item users can choose whether or not to show statistic in the TrendTable And the item is only applicable for TrendTable Menu Functions listed in below chart Patient ID Select the Patient ID that is needed to review Review Type Select the category that is needed to review Resolution Review Resolution only be applicable for TrendTable and TrendGraph Start Time Set up the starting time of review 43 2 TrendTable Interface TrendTable Interface showed as followed ID 1 Max Ave SpO02 99 99 PR bmp 60 60 TrendT able TIME SPO2 2008 05 06 15 54 58 2008 05 06 15 54 57 2008 05 06 15 54 56
14. tric and Adult 3 3 SPO2 Measurement Range 0 100 Resolution 1 Accuracy 2 70 100 Adult Pediatric non motion 3 70 100 Neonate non motion 0 69 unspecified Alarm Range 0 100 Refreshing Rate Is Pulse Rate Measurement Range 25 250 bpm Resolution Ibpm Accuracy 3 bpm non motion Alarm Range 25 250 bmp Refreshing Rate Is 4 Function Instructions 4 1 Main Interface The system will enter automatically the main interface after first startup Twelve parts make up of the main interface as follows charts ID 01 ADU 05 06 15 52 27 ID 01 ADU 05 06 15 46 18 Model 4 1 1 main1 Model 4 1 2 main2 Notice Between of the above figures the Model 4 1 1 shows the layout of the wave screen and the Model 4 1 2 shows the layout of the normal screen 4 1 1 Introduce the composing Parts as follows AR 7 8 9 Model 4 1 3 Main Patient ID Area This area shows the ID number of the patients monitoring currently Patient category Area This area shows the patient range Patients are classified as adult pediatric and neonate System Time Area Heart Rate Area Click the MJ button can shield the sound of the heart murmur The amp button and the Bl button flicker alternately after the sounds are turned off Battery symbol Area This area shows the electrical voltage of the battery Alarm Status Area r3 indicates that alarm sounds are turn
Download Pdf Manuals
Related Search