Home
MAN-138 - Toronto Stamp Inc.
Contents
1. CUIS TAE COST OF STAREAEAG AAS NUMBERALL STAMP amp TOOL CO INC USER MANUAL amp PARTS LIST 80 1 32 1 8 Characters S N P O BOX 187 1 HIGH ST www numberall com TEL 207 876 3541 SANGERVILLE ME 04479 office Onumberall com FAX 207 876 3566 MODEL 80 1 WHEEL QUICK CHANGE HEAD for 1 32 1 8 Characters Operating Instructions for Hand Shank Models 1 CAUTION ALWAYS WEAR SAFETY GLASSES WHEN STRIKING SHANK WITH A HAMMER BLOW DO NOT DROP OR ABUSE THE MODEL 80 Carelessness could damage the retaining pawls or retaining pawl spring Always lay the unit on its front side with the retaining pawl spring facing up The wheels are rotated by means of rotating the knurled knob 80 125 9 The wheels can be rotated in either direction This will control only the ones or units wheel The other wheels are rotated by means of spanner wrench The raised base of each character pad provides a step for the spanner wrench to grab When rotating the wheels to a new character make sure the retaining pawl is in the detent position The front of the Model 80 is the side on which the Numberall logo is stamped This side should be toward the operator when stamping After aligning the Model 80 with your work strike the shank with a hammer blow The size of the hammer and the force of the blow control the depth of impression LIGHTLY LUBRICATE THE MODEL 80 K
2. Change Numbering Machine PARTS LIST ED 207 876 3541 FAX 207 876 3566 80 125 16 N80 125 15 NN 80 125 14 80 125 37 lt r 80 125 5A MODEL 80 1 Wheel Quick Change Number Machine 6 PARTS LIST For 1 32 Through 1 8 Character Sizes 80 125 9 80 125 1 Frame N 80 125 5 Wheel Shaft with Pin 80 125 5 80 125 5A Wheel Shaft Pin 80 125 9 Wheel Shaft Turning Knob with set screw 80 125 11 Side Washer 80 125 12 Retaining Pawls 80 125 13 Retaining Pawl Shaft 80 125 14 Pawl Block 80 125 15 Pawl Block Cover Plate 80 125 16 Pawl Block Cover Plate Screws 2 required 80 125 17 Retaining Paw Spring S0 T2029 an dubl 80 125 18 Wheels Non Quick Change refer to price list gt 80 125 20 Wheels Quick Change refer to price list 80 125 22 Blank Spacers 80 125 26 Hot Stamping Equipment 80 125 28 Heating Element 80 125 29 Cord amp Switch 80 125 30 Coil Spring Protector 80 125 37 Spanner Wrench ALWAYS SPECIFY SERIAL NUMBER WHEN ORDERING PARTS Numberall Stamp amp Tool Co Inc For extra copies of this manual please call or visit our website P O BOX 187 1 HIGH ST www numberall com TEL 207 876 3541 SANGERVILLE ME 04479 office Onumberall com FAX 207 876 3566
3. 0 125 15 Remove the retaining pawl spring 80 125 17 When removing mark the outside of the spring so that it is not re assembled incorrectly Remove the pawl block 80 125 14 Loosen the set screw on the left hand knurled knob 80 125 9 and remove the knob from the wheel shaft Turn the knurled knob until the set screw in the knob is pointing towards the rear of the machine This will align a 1 16 diameter pin on the wheel shaft with the frame keyway Slowly and easily slide the wheel shaft out of the numbering head to the right The pin will have to pass through some of the numbering wheels the side washer 80 125 11 and the right hand frame leg It may be necessary to rock the shaft slightly in order to work the pin through Maintain a record of the wheel order for re assembly Replacing Retaining Pawls 1 2 Disassemble the marking head as per above Disassembly Instructions Using the flat of the spanner wrench carefully push the retaining pawl shaft 80 125 13 and retaining pawls 80 125 12 out of the slot in the pawl block 80 125 14 Do not bend the retaining pawls Maintain the original positioning of the retaining pawls slide the pawls off the shaft Revision 2 0 Replace the retaining pawls as necessary and slip all of the retaining pawls onto the shaft in the original order Align the retaining pawls on the shaft so that they drop into the milled slots Position the sha
4. eep the wheels and parts free from dirt and grit The clearances are very tight and accumulated dirt grit or oil may bind the machine On Model 80 machines with the wheels indexed for direct sight reading the stamped character sequence can be read by reading the sequence that is depicted by the arrows that are stamped on the frame The arrows point towards characters that will do the stamping This is the sequence that is to be stamped The arrows are located so that a person sitting down can read the indexing correctly Operating Instructions for Press Models 1 When inserting the Model 80P in the press make sure the frame bears the load The shank should serve only to locate the Model 80P and keep it from falling out No load should bear on the shank Revision 2 0 2 3 The front of the Model 80P is the side with the Numberall logo stamped on it This should be facing the operator or towards the front of the press depending on the orientation of the work to be stamped Follow the following instructions listed above Steps 2 3 4 7 and 8 Disassembly Instructions 1 When ordering parts or reguesting information ALWAYS refer to the numbering head s serial number stamped on the right hand side of the frame Select a clean bench that is free of dirt and grit to disassemble the Model 80 Remove the pawl block machine screws 80 125 16 on the back of the unit Then remove the pawl block cover plate 8
5. ft left and right so it clears the screw holes Press the retaining pawl shaft into its slot until it bottoms The shaft must rest on the bottom of the slot On rare occasions when a new retaining pawl is combined with a used wheel a very slight misalignment of the wheel relative to the other wheels can occur This can be corrected by honing the radius of the pawl The radius of the pawl must remain unchanged while the center of the radius is moved slightly Care must be exercised not to remove too much metal otherwise the spring tension on the retaining pawl will be reduced Factory trained personnel can easily replace retaining pawls so it is recommended that the numbering head be returned for service if you have difficulty with this process Assembly Instructions 1 Make sure the surfaces of the character wheels and parts are clean USE A LIGHT LUBRICANT Start the wheel shaft 80 125 5 into the right hand side of the frame 80 125 1 Make sure the set screw of the knurled knob is positioned to the rear Slide the wheel shaft part way into the frame opening Beginning with the side washer 80 125 11 push the washer and then the wheels in the original order onto the wheel shaft The index plate side of the wheels should be against the side washer NOTE The ones or units wheel is the only wheel with a broached spline This wheel must go on after the side washer or the Model 80 cannot be asse
6. mbled After all of the wheels are in place push the wheel shaft further left until it is flush with the frame It may be necessary to rock the wheel shaft to help slide through the wheels and frame leg DO NOT FORCE Turn the numbering head over with the pawl block mill cut facing up and the frame legs facing toward the operator Place the pawl block 80 125 14 with the retaining pawls and shaft in place into the mill cut The semi circular ends of the retaining pawls should be facing down Make sure each retaining pawl 80 125 12 rests in its own slot Revision 2 0 7 Place the retaining pawl spring 80 125 17 over the pawls so that the spring tines are centered above each pawl the marked side of the spring should be facing out Place the pawl block cover plate 80 125 15 over the spring and evenly tighten the pawl block screws 80 125 16 Make sure the pawl block is seated in the mill cut After tightening the machine screws rotate each wheel Every wheel should positively indent without any binding or rocking Recommended Spare Parts 1 Side Washer 80 125 10 2 Retaining Pawls 80 125 12 1 Retaining Pawl Spring 80 125 17 1 Spanner Wrench 80 125 37 Spare Wheels should also be stocked depending on use and material being stamped Revision 2 0 NAN 4 d r NUMBERALL STAMP amp TOOL CO INC BOX 187 HIGH ST SANGERVILLE ME 04479 Model 80 1 Wheel Quick
Download Pdf Manuals
Related Search
Related Contents
Instrucciones instalación, configuración (Español) Nortel Networks DS30 User's Manual Transferir - produktinfo.conrad.com Sony CDX-R505X CD Player User Manual Copyright © All rights reserved.
Failed to retrieve file