27938-01A rejuvasun 07:27938-01A rejuvasun `07
Contents
1. Oty A B C A Face tanner control Turns face tanners on and off during use B_Rejuvasun M control Turns Rejuvasun unit on and off C Body fan control Controls the speed of the body fan during use D Body fan speed indicator Indicates speed of fan OFF LOW MED HIGH E Timer display Displays remaining time F Stop button Interrupts tanning session G Timer button Turns bed on Timer dis play shows remaining time If a lesser time is desired press timer button until desired time is displayed stand alone mode only WARNING Wear protective eyewear Failure to may result in severe burns or longterm injury to the eyes D 18 YY yy me Operation Using Your Sunbed Operation as a stand alone unit or connected to a remote system using a control relay If using T Max see right 1 3a 3b 19 Lift the canopy lie down on the bench face up lower the canopy toward your body using the canopy handle For best results position the canopy as close to your body as possible maintaining at least 4 10 2 centimeters from your body Put on your safety goggles If you want a full tanning session press the timer button G previous page to begin the tanning session The lamps will turn on including rejuvasun and the timer will begin to count down If you want to use the rejuvasun only sim ply press the the rejuvasun button B Wh2. SERPS OL QU I OREN AR LA En 48 MONTH GOLD MEDAL WARRANTY i Your ETS Distributor including ETS LLC if purchased directly through a manufacturers warranty warrants your tan ning unit to be free of structural defects in material and workmanship under normal use for its lifetime Your ETS Distributor will at its discretion repair any structural defect which materially affects the performance of the tanning E unit or replace the tanning unit EUR REA For forty eight 48 months following the purchase date of your tanning unit your ETS Distributor will provide replace ments for parts that prove to be defective in material or workmanship with the following exceptions gas springs ballasts electronic lamp starters and the Rejuvasun panel are warranted against manufacturer s defects for a period of one 1 year glow tube lamp starters and cracked or broken endcaps are warranted against manufacturer s defects for a period of ninety 90 days fluorescent lamps are warranted against manufacturer s defects for a period of thirty 30 days acrylics are warranted against manufacturer s defects for a period of one 1 year prorated following the purchase date of your tanning unit Shipping charges will be covered during the first ninety 90 days following the purchase date x POOLE Sana tae Sl sav i SOS rac ib eine A ard i CRU DIE TN Your ETS Distributor including ETS LLC if purchased directly a
3. e IMPORTANT Voltage must be below 230V AC or may require a Buck Booster eSome portions of the carton may be used for assembly Do not discard car tons until assembly is complete e You will need a 2 Phillips screwdriver to assemble this tanning ae CAUTION Use of a voltage source above 230V AC may prevent proper operation of the sunbed and could cause damage and void the warranty A CAUTION Air from the room is used to cool the sunbed Maximum ambient room temperature should be 80 F Place your sunbed no closer than 6 from any wall Make sure nothing obstructs the airflow into or out of the fan openings A poorly ventilat ed room may cause the unit to become hot and cause discomfort to the user A CAUTION Proper assembly of your sunbed requires three people Plan to have a couple of helpers assist you M A R Installation Hardware Inventory KUSI Nylon Floating Bearing Ouantity 4 Hardware Inventory Open the hardware bag Remove a hardware In addition to a phone type R gt 11 cable and pillow make sure you sa the following items Ange rin 5 16 x 2 1 32 Quantity 2 Hinge Pin Locking Clip Quantity 2 Clevis Fork J M10 Long Access Panel Key K Quantity 2 Quantity 1 a N Bronze Bushing 10mm Ouantity 2 Clevis Pin 10mm Safety Goggles Quantity 2 Quantity 1 Retaining Ring Quantity 2 ep ir Screw 10 x 1 2 Quantity 8 A WARNING Always wear
4. Face Tanner Assembly Outer Fan Body Fan Cooling Fan Grill Plastic Fan Relay Filter Gas Springs Hardware Kit Complete Hardware Kit Assembly Hour Counter Ignitor Label English Warnings Label French Warnings Lamp Holder w Starter Lamp Holder w o Starter Lamp Holder Face Tanner Lamps LED Accent Light LED Power Supply Pillow Remote Connection PCB Remote Control Bypass Plug Rejuvasun Panel Rejuvasun Power Supply Schematic Packet Starter Electronic main lamps Support Bench Acrylic Thermostat for face tanner Timer Timer Interlink PCB Timer Keypad Timer Keypad Pushbuttons Trim Profile grey Wiring Harness Keypad Link Wiring Harness Remote PCB to Timer Wiring Harness Timer in Tray Wiring Harness RJ 11 Canopy to Tray Record this information for ease of service Date of purchase Serial number Not shown VLO 8 E627 27938 01A WHEN After each use Monthly 400 500hrs 700 1000hrs Clean Disinfect Interior Surfaces v Clean Lamps Clean Reflectors Clean Exterior Check Clean Fanst SSI IS Change Lamps v Tam Check Fasteners nuts bolts etc I Check Power Cords v J Change Filter v See Care and Maintenance See Lamp and Acrylic Replacement Fans are located on top of the canopy under the bench and at the side of the ballast drawer Use a vacuum to clean MAINTENANCE LOG What When What When What When e B
5. D a157 Rejuvasun 332 Size 56 40 _ 86 1 2 40 Tm Weight Pounds 530 Recommended Room Size ZXY Electrical Voltage AC 220 Amperage 17A Circuit Breaker Recommended min 30A Outlet Hardwire Main Lamps bench Velocity Main Lamps canopy Velocity PLUS Ballasts 100W Face Tanner SolarMax IFT FT Ballasts 400W Body Cooling System plus Full side fan panel 230cfm Turbo Timer System Digital Max Exposure Time 20min tanning 20min Rejuvasun M Back up Timer On board Watchdog Remote Capability EAs in the U S A T Max compatible Proudly manufactured
6. X N Scenario 1 T Max amp Manager with Co Complete Wireless Connect one AP 900 with Power Injector to the Manager and one AP 900 to each of the tanning beds Install as many beds as you like with this configuration Units that do not communicate with T Max will need an AP 900 with Power Injector and an additional 3A to operate You can place your sunbed at any location in the series Cp Cp Scenario 2 T Max Manager with Wireless combo Wireless can be easily added to an existing salon already utilizing T Max Connect one AP 900 with Power Injector to the Manager and one AP 900 to each wireless ready tan ning bed The rest of the salon may be daisy chained together and connected to the Manager Pro T _ Non T Max incorporated units Scenario 3 T Max Manager K Series with Wireless combo Connect one AP 900 with Power Injector to the Manager and one AP 900 to a wireless ready tanning bed The rest of the salon may be daisy chained together and connected to the wireless equipped tanning bed eliminating the need to wire the Manager to the tanning beds lt Non T Max incorporated units 14 N p lt 4 Installation Remote Connections ma Scenario 4 T Max amp Manager with wires As always this tanning bed is fully compatible with a wired T Max system Simply connect the RJ 22 modular cable s described in the T Max Manager manual into the A
7. casing and lock it closed with the screws Ensure that the screws firmly secure the glass casing A DANGER Unfiltered light from face tanner can cause severe burns Never turn sunbed on while face tanner is disassembled or when glass filters are removed Immediately discontinue use of this equipment if face tanner glass is broken or any unfiltered light can be seen escaping face tanner assembly lo N RETAINING SCREWS 23 VIO 8E6L7 27938 01A ed X MPE A roubleshootin n ec 24 Problem Sunbed not tanning Lamps fail to light and timer dis play is blank One or more lamps fail to light The canopy will not stay up The face tanners will not come on The last minute of tanning time does not count down from 59 sec onds but some time less than 59 seconds forgot what address or id set my sunbed to Solution Clean sunbed see Thorough Periodic Cleaning Ensure supply voltage is between 208 and 230V AC Replace lamps if lamp hours are greater than 800hrs Replace acrylic Make sure the unit is connected to a power source Check source of AC power Reset circuit breaker or replace fuse Check that lamp is installed correctly Switch unlit lamp with a lamp that lights if new lamp lights and old lamp still doe
8. ILITY DAMAGE OR EXPENSE IN AN AMOUNT IN EXCESS OF THE PURCHASE PRICE RECEIVED OR FOR LOSS OF USE OR PROFITS LOSS OF TIME INCONVENIENCE RENTAL OR SUBSTITUTE PRODUCTS LOSS OF BUSINESS LOSS OF INCOME OR ANY OTHER INCIDENTAL INDIRECT SPECIAL OR CONSEQUENTIAL DAMAGES Some states do not allow the exclusion or limitation of incidental or consequential damages and the above limitation or exclusion will not apply to residents of some states This 48 Month Gold Medal Warranty gives you spe cific legal rights and you may have other rights which may vary from state to state SALTS AS LLL IERI LN Sin aM ET RIGS Mi ER IEE NENA ETIR ERI EEE v UVS NOKIA ELLIT SIIS ME Pg ITA All warranty service must be performed by an authorized service person using only ETS authorized replacement parts Use of non authorized parts may void your warranty All labor charges must be authorized by your ETS Distributor prior to the start of repairs and must not exceed the established rates and time allotment policies established by your ETS Distributor If your tanning unit must be returned for service within thirty 30 days from the purchase date freight charges will be paid for by your ETS Distributor after which all freight charges shall be at your expense Contact your ETS Distributor for the authorized Service Center nearest you This warranty is serial number specific and only applies to tan ning units purchased through an authorized ETS Distributor This warr
9. SSEMDIY sus estime ri a ei 11 Remote Connections 30 a ie ie pre na 12 Operation iui pi e Gon weit era eso 17 Before You Tams 42445488 aa i 17 Exposure TIMES sagerat ti piae Akasa sus hace dser ice 17 Using Your Sunb d s sauts ins Penns a 18 Care and Maintenance 4444 5444 aamen tet ens aan 20 Cleaning Alter Useimmat ss a Dana DL Varta aa E 20 Thorough Periodic Cleaning 20 Mechanical Inspection 20 Lamp and Acrylic Replacement 21 Troubleshooting siris nienia se sn man ric 24 Wed w N n afety Information s LABELING NOTICE Labels are affixed on all systems to inform the user of possible dangers Regulations are stated in 21 CFR Section 1040 20 and require that all products manufactured after September 8 1986 which use sunlamps must display the following D ANG F R Ultraviolet radiation Follow instructions Avoid overexposure As with natural sunlight overexposure can cause eye and skin injury and allergic reactions Repeated exposure may cause premature aging of the skin and skin cancer WEAR PROTECTIVE EYEWEAR FAILURE TO MAY RESULT IN SEVERE BURNS OR LONGTERM INJURY TO THE EYES Medications or cosmetics may increase your sensitivity to the ultraviolet radiation Consult physician before using sunlamp if you are using medications or have a history of skin problems or believe yourself especially sensitive to sunlight If you
10. Step 4 Wipe the reflectors with a clean damp cloth Step 5 Reinstall the lamps and acrylic shields Step 6 Clean or replace air filter on top of ballast tray Replace with a 10 x 24 x 1 furnace filter Mechanical Inspection Your tanning bed has been built for years of service To ensure trouble free operation throughout its life inspect the unit s mechanical integrity every 400 500 hours of use e Inspect the units fasteners verifying that all are firmly in place e Inspect gas springs for signs of wear Gas springs that will not hold the canopy in the full open position when raised should be immediately replaced See Troubleshooting e Inspect the AC power cord and its connections e Inspect the acrylic Broken cracked or badly scratched acrylics should be immediately replaced 20 NY M RE Lamp and Acrylic Replacement Introduction To be assured of maximum tanning effec tiveness change lamps after approximate ly 700 1000 hours of use Tanning will continue after this time but at a slower rate To ensure trouble free operation of your sunbed replace the lamp starters whenever the lamps are replaced WARNING Shock hazard Disconnect power before removing any protective covers 21 I Care and Maintenance Lamp and Acrylic Replacement Opening Replacing Acrylic Shields The acrylic shields are secured in place by turn latches along the front edge Use a flat bladed screwdriver to tu
11. amps have come on a tanning time but the lamps have not come on When auto addressing the first bed does not register an id When using a T Max 1A my sunbed won t function properly My salon suffers frequent short power outages and clients com plain about losing session time W 7 Troubleshooting SX Solution You have probably attempted to connect your sunbed to the remote system already Disconnect the remote plug s from the ports at the back of the sunbed wait 90 seconds and try again Remote device has not been set The sunbed has not been connected to the remote system see Remote Connections Delay time of TMax Manager has not been set Delay time has expired and session has begun Auto start function of T Max Manager has been turned off Press the timer button to turn on lamps When using the auto address feature of the T Max Manager you must wait 10 seconds from the time you start the auto address function before addressing the first bed SunStar Bypass plugs or terminator plugs may be needed if the T Max 1A and the sunbed are over 100 feet apart Install the plugs in the open remote port in the sunbed and the T Max 1A If you have a T Max Manager changing parameter 23 from 0 to 1 will allow the tanning bed to remember how much time was left when power goes out and resume its session after power is restored Consult your T Max Manager manu al for information on setting
12. anty is extended to the individual or legal entity whose name appears on the original sales document and may not be transferred to any other individual or legal entity This warranty is void if the tanning unit is modified in any manner from its original design DEDE DE TVE NERA TVE NAIIVI BAIN IRI KNITS KKT To obtain warranty service contact your place of purchase Proof of purchase including serial num ber is required for verification Contact ETS LLC only if you purchased your equipment directly ETS LLC 7445 Company Drive Indianapolis IN 46237 9296 f 1 800 449 3605 In Canada call 1 800 661 6292 or 519 421 1212 VLO 8 E6L7 27938 01A N AA Kies Congratulations on your purchase of this technologically advanced sun tanning unit Not only is this I elcome unit designed and manufactured for years of dependable service the new Rejuvasun unit opens up a new revenue channel for your salon Please read all the instructions in this booklet before installing and using the unit Always be sure to observe all safety precautions D A Eontnt SI Safety Informations 42 ses aus Cie beak alate iii Installation sassari ra 1 Unpacking and Inspection 1 Pre Installation Planning 2 Hardware Inventory 2 544 samas siens dn ada pa 3 Assembly Procedures 4 Electrical Connections 01 6 iii 10 FINALA
13. awer with a Phillips screwdriver Note The cartons are reusable You may wish to save them for future use Ax CAUTION DO NOT lift the canopy using the plastic end caps They are not designed to hold the weight of the unit and may break causing damage to the unit and possible injury After unpacking the unit check to make sure you have received the following e Canopy unit e Bench unit e Ballast drawer e Body fan kit e Pair of gas springs e 2 endcaps one with slots for the body fan bracket e Front access panel e Bag containing necessary assembly hardware safety goggles and pillow Inspect these items including the canopy and bench and make sure they are free from any visible damage Report the extent of any damage to the transportation company Record the serial number of the unit in the area provided at the back of this manual This information will be required whenev er you Call customer service VLO 8 627 27938 01A Pre Installation Planning RY 7 Installation Pre Installation Planning O Before you begin to assemble your sunbed you should observe the following consid erations A WARNING Shock hazard Disconnect power before servicing e The Rejuvasun 332 requires a dedicat ed circuit capable of providing 30 Amp service at 220VAC This unit must be hardwired directly to a junction box on a dedicated circuit We recommend con nection by a professional electrician
14. cables are plugged into your sunbed s remote ports Remove and reapply power to the unit Press and hold the stop button located on the sunbed display for three seconds and release The display should indicate an id number from oF to 252 1 99 FOC 100 199 E QU 200 252 50 If you are using a T Max 1A or 3A as a master remote the id of the sunbed must be set to 1 If you are using a T Max Manager each sunbed must be assigned a different id To set the id press the timer button to count up or the body fan control button to count down until the desired number is achieved Press the stop button to return to the normal display mode Installation Remote Connections ak S PE 16 dg W 077 A Ke peration ee Before You Tan Before using your sunbed please note the following important precautions e Your skin should be free of cosmetics oils or other body lotions prior to tan ning except for those specifically made for use with tanning devices However do not remove natural body oils by bathing or showering immedi ately before tanning e Your hair should be free of gels mousses sprays or other hair products prior to tanning These products can cause damage to the sunbed acrylic As an alternative a shower cap or towel can be worn to keep treated hair away from the sunbed surfaces e This unit intended for individual
15. do not tan in the sun you are unlikely to tan from the use of this product Children the elderly or fair skinned people who always burn easily and either never tan or tan minimally should not use this eguipment To use lie down under canopy and pull down as far as adjustment will allow Minimum use distance from face tanner is 4 inches 10 2 centimeters otherwise overexposure may occur Minimum use distance elsewhere is touching the clear plastic panels Do not use with out clear plastic panels in place Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once a day Tanning normally appears after the first few sessions and maximizes after approximately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 20 MINUTES Level 1 Week 1 Skin Type 1st 3rd Sessions Sensitive Skin Burns easily and severely and does not tan NOT RECOMMENDED FOR TANNING Level 2 Level 3 Level 4 Level 5 Light Burns easily and severely and tans minimally 8 12 16 20 Ill Normal Burns moderately and tans average 10 15 20 20 IV Dark Burns minimally tans easily and above average 16 20 20 New lamps emit approximately 10 more ultraviolet radiation during the first 50 hours of operation Recommended tanning times
16. e bronzage commence normalement appara tre apr s les premi res s ances il atteint son apog e au bout d environ quatre semaines Les personnes qui ont d j un teint hal peuvent commencer a des niveaux plus lev s selon l im portance de leur hale initial TEMPS D EXPOSITION RECOMMANDE EN MINUTES LE TEMPS D EXPOSITION MAXIMAL EST DE 20 MINUTES Elev 1 Semaine 1 ere e Elev 2 Elev 3 lev 4 lev 5 Type de peau Peau sensible br le facilement et ne bronze tn RECOMMANDE lll Peau normale br le et bronze de fa on a a 15 IV Peau fonc e br le tr s peu bronze plus facilement que la moyenne 12 16 Les lampes neuves mettent approximativement 10 de plus de rayons ultraviolets au cours des 50 premi res heures de fonction nement Le temps de bronzage doit donc atre r duit d environ 10 pendant cette p riode AVERTISSEMENT Lisez le livret d instructions avant d utiliser cette lampe solaire e Les autres personnes pr sentes dans la pi ce doivent aussi porter des lunettes protectrices lorsque les lampes sont allum es Coquilles de protection pour les yeux recommand es Ultra SunGlobes special eyez ou l quivalent tel que le stipule le document 21 CFR 1040 20 Les autres types de lunettes protectrices peu vent ne pas assurer une protection ad quate Utilis sans lunettes protectrices ce produit peut causer des br lures ou l sions oculaires graves Si vous souffrez d un malaise a
17. en the timer reaches 0 the lamps turn off If you want to stop your session before time expires press the stop button F You will have ten seconds to restart with the remaining time otherwise the timer will reset to 0 Raise the canopy by using the outer edge of the canopy do not push up on the acrylic shield The cooling fans run for a period of time after the lamps shut off to aid in cooling the sunbed Operation while connected to a T Max remote system If using other remotes or no remote sys tem see left Note See Remote Connections for important information about the T Max remote system 1 4 Lift the canopy lie down on the bench face up lower the canopy toward your body using the canopy handle For best results position the canopy as close to your body as possible maintaining at least 4 10 2 centimeters from your body Put on your safety goggles Assuming the remote system has been set to allow a pre tanning delay time the timer display E will repeatedly flash the delay symbol dL and then the remaining delay time Press the timer button G or wait until the delay time has expired to begin the tanning session The lamps will turn on and the timer will begin to count down When the timer reaches 0 the lamps turn off If you want to stop your session before time expires press the stop button F Raise the canopy by using the outer edge of the canopy do n
18. et la peau et provoquer des r ac tions allergigues Une exposition r p t e peut causer le vieillissement pr matur de la peau et provoquer le cancer de la peau PORTEZ DES LUNETTES PROTECTRICES LE NON RESPECT DE CETTE CONSIGNE DE SECURITE PEUT ENTRAINER DE GRAVES BRULURES OU DES LESIONS OCULAIRES LONG TERME Les m dicaments ou les produits cosm tiques peuvent augmenter votre sensibilit au rayonnement ultraviolet Consultez un m decin avant d utiliser la lampe solaire si vous prenez des m dicaments si vous souffrez d une maladie cutan e ou si vous croyez tre particuli rement sensible aux rayons du soleil Si vous ne bronzez pas au soleil il est peu probable que vous bronzerez sous une lampe solaire Les enfants les personnes ag es et les personnes qui ont une peau claire qui br le facilement ne bronze jamais ou alors tr s peu ne devraient pas utiliser cette lampe tendez vous sous la partie sup rieure puis abaissez celle ci aussi bas que possible La distance minimale d usage de l appareil de bronzage pour le visage est de 4 pouces 10 2 centim tres afin d viter une exposition excessive Les autres parties du corps peu vent toucher les panneaux de plastique transparents N utilisez pas la lampe sans les panneaux de plastique transparents La premi re semaine de bronzage les personnes qui n ont pas un h le initial ne doivent pas se faire bronzer tous les jours Ne vous faites jamais bronzer plus d une fois par jour L
19. h These are for the remote cables to keep them out from under the ballast drawer when rolling the drawer in and out of the unit Route the remote cables as shown below leaving some slack for the drawer to roll out FAN HOUSING UNDER BENCH REAR TO REMOTE PORT REMOTE PORTS L WIRED WIRELESS REMOTE REMOTE PORTS RJ 22 PORT RJ 11 12 M I gt Installation Remote Connections FA Remote Connections Your sunbed incorporates advanced circuitry allowing it to connect and communicate with most remote control systems If a remote sys tem is to be used first determine whether the remote system is a T Max Manager Pro System or a standard remote system operating with a control relay Follow the appropriate instructions for your system type CAUTION The remote connection is not designed to supply or accept high voltage nor can it provide power to an external timer The sunbed s remote inter face circuitry operates on 5 volts attempting to connect it to any higher voltages will damage the sunbed as well as void your warranty T Max Manager Series The T Max amp Manager series offers the ulti mate in sunbed control while allowing the tanner easy straightforward operation Your sunbed is configured to directly connect to this system including the new wireless remote system The circuitry inside your sunbed eliminates the need for the T Max 1A or 3A when connecting to the T Max Manager series Y
20. lso extends to you a two 2 year parts warranty on all T Max remote system components External voltage transformers buck boosters are covered by a one 1 year parts and labor warranty provided you send back the defective transformer Labor costs associated with repair or replacement work covered by this warranty will be reimbursed for repair or replace ment work required to be performed for a period of ninety 90 days following the shipping date of your tanning unit Normal wear and tear damage from misuse or abuse damage incurred in transit or damages resulting from unauthorized repairs or modifications are not covered by this warranty Warranty coverage does not include cosmetic abnormalities such as scratches nicks dents or other cosmetic changes that do not materially interfere with the function of the tanning unit THIS 48 MONTH GOLD MEDAL WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH ARE HEREBY DISCLAIMED No one has the authority to change or modify this 48 Month Gold Medal Warranty in any respect To obtain service under this 48 Month Gold Medal Warranty contact your authorized ETS Distributor or ETS LLC if purchased directly Proof of purchase including serial number is required IN NO EVENT SHALL YOUR DISTRIBUTOR OR THE MANUFACTURER BE LIABLE AT LAW OR IN EQUITY FOR ANY LOSS LIAB
21. nstructions for installing the fan are included with the body fan kit Follow those instructions to install the body fan Put the head end endcap the one without slots on top in place and secure with two 10 x 1 2 screws in the two middle holes Use two 10 x 1 screws in the two outer holes V10 8 6 7 27938 01A Electrical Connections At the rear of the sunbed connect the two canopy power cords and two bench power cords from the ballast tray to their respective power receptacles Simply match the plug to the receptacle push on firmly and secure by twisting the threaded locking ring Connect the RJ 11 phone type cable between the canopy and rear jack on the ballast drawer The three jacks on the front of the drawer are for remote connections Connect main power cord as described in Pre Installation Planning PIN CONFIGURATIONS MAY VARY FROM SHOWN ak S Installation Electrical Connections gt Helpful Hint Line up the plug with the proper receptacle and push in Apply pressure to the plug and twist the locking ring counter clockwise until you feel the plug click into place Then turn the lock ing ring clockwise to secure it The ring will click when fully engaged 10 M A R Installation Final Assembly GENI Final Assembly Make sure the air filter is in place on top of the ballast drawer It simply sits on the drawer over the air slots and is held in place by airflow when the uni
22. o lose their effectiveness even though they continue to light Recommended Replacement Acrylics Acrylics vary greatly over time in their ability to effectively transmit UV light Acrylics sold by ETS have been life tested to ensure proper transmission throughout their useful life ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EOUIPMENT Bench lamps Velocity amp Wolff amp Model VEL71 T12 100W PREHEAT BIPIN Canopy lamps Velocity PLUS Wolff amp Model VLP71 T12 100W Bi Pin SolarMax IFT facial unit if equipped Heraeus E400 HPT or Philips Model HPA 400 30s or CosmoTech Model 23045 22 S M FA Removing Replacing Face Tanner Lamp After removing the canopy acrylic shield replace the face tanner lamp as follows Step 1 Support the face tanner assembly with your hand while unscrew ing the two retaining screws The face tanner glass casing will swing downward Step 2 The lamp can now be exchanged The lamp holders are eguipped with spring con tacts which enable the lamp to be removed easily Remove the old lamp and discard Install the new lamp using a clean cloth or paper towel Ensure that the lamp is firmly seated in the lamp holders I Care and Maintenance Lamp and Acrylic Replacement Note Never take hold of the lamp such that your fingers are in contact with the lamp glass Finger oils will greatly reduce the lamp s operational life Step 3 Gently close the face tanner glass
23. ot push up on the acrylic shield The cooling fans run for a period of time after the lamps shut off to aid in cooling the sunbed The timer will indicate as a reminder to clean the sunbed After the sunbed is cleaned press the timer button and the display will return to 0 VLO 8 627 27938 01A e 7 Ud N Cleaning After Use Clean and disinfect your tanning bed s bench and canopy after each use Use a non abrasive disinfectant cleaner that does not contain ammonia or ammonia deriva tives Ammonia may damage the acrylic shield Spray the acrylic lightly with disin fectant and wipe dry with a clean soft cloth We recommend Australian Gold amp pH Neutral Disinfectant Cleaner Thorough Periodic Cleaning Introduction The cooling fans draw air through the bed and over time will cause a dust buildup on the lamps and reflectors This will reduce the tanning effectiveness of the bed When a dust buildup is observed it is necessary to thoroughly clean the inside of the bench and canopy WARNING Shock hazard Disconnect power before removing any protective covers Cleaning the Canopy and Bench Step 1 Open the acrylic shields and remove lamps as described in Lamp and Acrylic Replacement pere and Maintenance Step 2 With a soft cloth wipe the entire length of each lamp to remove any film buildup Step 3 Clean both sides of the acrylic shields with a non ammonia dis infectant cleaner
24. our sunbed supports the auto address ing feature of the Manager and the following parameters 5 6 7 8 9 10 15 and 23 See your T Max manual for descriptions of these parameters and how they function 13 REMOTE PORTS WIRED WIRELESS REMOTE REMOTE PORTS RJ 22 PORT Ru 11 Special Note on T Max The Rejuvasun 332 requires the latest soft ware in your T Max Manager to properly con trol the sunbed To check for this when apply ing power to a Manager Pro a 3 digit version number will appear on the left hand side of the screen This must be 415 or higher An upgrade CD is included with your sunbed Follow the instructions on the CD T Max Wireless Remote System The T Max AP 900 eliminates wires in your salon allowing easy setup without hiring an electrician to run wires It also protects your investment from damage by isolating each unit from one another Your sunbed arrives wireless ready which means it connects directly to the T Max wireless system Older tanning beds and T Max managers also uti lize this system but require a T Max Power Injector PI to provide the needed power to the wireless unit Remote System Hook up Scenarios Follow the diagrams on the next page to see the many different scenarios for hooking up your salon If you need further assistance call T Max directly at 471 272 0761 VLO 8 627 27938 01A Dr Installation Remote Connections
25. parameters 26 TIMER KEYPAD WIRING HARNESS KEYPAD LINK ENDCAP CANOPY LABEL FRENCH WARNINGS FAN W O STARTER COOLING ACCESS PANEL LAMPHOLDER REJUVASUN POWER SUPPLY LABEL ENGLISH BALLAST CANOPY MOUNTING ARM CAPACITOR 754F CONTACTOR FACE TANNER WARNINGS LAMPHOLDER W STARTER S 332 3F JUV ACRYLIC BENCH VIO 8E6L7 CAPACITOR CONTACTOR TIMER INTERLINK HOUR COUNTER CURRENT SENSOR FAN RELAY REMOTE CONNECTION PCB WIRING HARNESS TIMER REMOTE PCB TO TIMER WIRING HARNESS TIMER IN TRAY LED POWER SUPPLY FAN COOLING Ballast Tray VLO 8 E627 Parts List This is a list of parts which may be replaced by the consumer Care should be taken when replacing anything related to electrical wiring We recom mend contacting a professional electrician When calling for parts first state your bed model as S 332 3F JUV Then refer to this list and preceding illustrations for proper part identification Access Panel Access Panel Key Acrylic Bench Acrylic Canopy Acrylic Edge Trim Canopy Acrylic Protector Strip on bench support rail Ballast 100W Ballast Face Tanner 400W Bearing Nylon Floating Bushing Bronze 10mm Canopy Mounting Arm Capacitor 1uF Capacitor 75uF Contactor Contactor for Face Tanner Cover Canopy Current Sensor Endcap Endcap Canopy Head End Endcap with Body Fan Cut outs
26. protective eyewear when unit is on Phillips Screw 10 x 1 Failure to may result in severe burns or Quantity 8 longterm injury to the eyes VLO 8 627 27938 01A N s LE gt Installation Assembly Procedures AGE ma Assembly Procedures Stand Assembly 1 Place the bench unit approximately where it will be when assembled Leave some room behind it to work 2 Slide the ballast drawer under the bench as shown with the cables toward the back NY yy N e MC IS Installation Assembly Procedures Install Canopy Lay something across the bench such as some cardboard or a blanket to protect the units and place the canopy on the bench with the canopy hinge arms toward the back Once again do not use the canopy plastic endcaps to lift the unit A CAUTION DO NOT lift the canopy using the plastic end caps They are not designed to hold the weight of the unit and may break causing damage to the unit and possible injury VLO 8 627 27938 01A ako Installation Assembly Procedures A dl ma 2 Insert the Nylon Floating Bearings into the canopy hinge arms and carefully lower the hinge arms into the bench uprights 3 Secure the arms in place with the Hinge Pins and Hinge Pin Locking Clips A A La a g a I BBE gt Os D DE See BABS mal 5 OODI LO EEE LA 2 D Sal ca gt Bench Upright I A R Installation Assembl
27. r display changes to indicate 1 Bypass plug is not installed see Electrical Connections a tanning time after the timer but 2 A non SunStar bypass has been used See Electrical ton is pressed but lamps do not Connections come on 3 If remote is being used other than T Max Manager the exter nal timer may not be activated 4 Remote wiring is incorrect see the instructions provided with the remote interface kit My bed is connected to the T The auto start feature of the remote system is disabled see the Max Manager remote system instructions provided with your remote system and when the delay time has expired the timer display starts counting down but the bed lights do not come on My bed won t work with the T 1 The sunbed must first be set to a unique address see Remote Max Manager remote system Connections 2 The bypass or terminator plug may be installed in the series in an inappropriate location Plug the bypass plug only into the bed at the end of the series Timer display continues to show af1 T Max amp Manager remote system has not yet been set O after the timer button is pressed 2 Sunbed address is not set correctly see Remote Connections 25 VLO 8 627 27938 01A Problem My bed is connected to a T Max remote system but am having trouble getting into id mode My bed connected to a T Max Manager did not display dL but does indicate 0 a tanning time and the l
28. remote port s located on the ballast drawer and follow the instructions that came with your remote system incorporated units Scenario 7 Non T Max Remote System wired to unit Non T Max Most non T Max remote systems control the Remote System sunbed by the use of a relay The relay operates using control relay the sunbed by connecting and disconnecting a pair of wires leading from the sunbed Refer to the user s manual provided with your remote system to determine if it operates in this way To connect your sunbed to this type of system a remote inter face kit is reguired Contact your place of purchase L to obtain the kit The illustration below details a i typical connection Follow the instructions provid Remote Interface Kit ed with the kit and from the remote s manual to make the necessary connections CAUTION The remote connection is not designed to supply or accept high voltage nor can it provide power to an external timer The sunbed s remote inter face circuitry operates on 5 volts attempting to connect it to any higher voltages will damage the sunbed as well as void your warranty 15 V10 8 6 7 27938 01A Setting the sunbed address manually Before connecting your sunbed to the T Max Manager or T Max 1A or 3A the address of your sunbed must first be set Set the id man ually as described below Setting the id a Make sure no
29. rn the latches a quarter turn to open the acrylic The acrylics swing open on a hinge On the inside of the bench along the front are two supports for the bench acrylic Swing them up to hold the bench acrylic open Both acrylics may be removed by lifting them out of the channel along the back edge When you are finished simply reverse the above directions to secure the acrylic shields A CAUTION Be careful The edges of the acrylic shield may be sharp Rejuvasun Unit Maintenance The rejuvasun facial unit requires no regular maintenance except to make sure it is free of dust Carefully wipe it with a clean dry soft cloth VLO 8 627 27938 01A RY M Care and Maintenance Lamp and Acrylic Replacement aa Removing Replacing Fluorescent Lamps After opening the acrylic shield replace lamps as follows Step 1 Grasp the lamp at one end and at the middle and turn the lamp one quarter turn Gently remove the lamp from its holders Step 2 Reinstall the lamp by inserting the pins located on the ends of the lamp into the slots on top of the lamp holders and turn the lamp a quarter turn It should click in place PE Recommended Replacement Lamps We recommend using the lamps specified below Use of uncertified lamps is a viola tion of Federal regulations and will void your warranty These lamps have an aver age life of 700 1000 hours of effective tanning use Lamps used longer than that begin t
30. rr tez l utilisation et consultez un m decin SEULES LES LAMPES SUIVANTES ONT T HOMOLOGU ES POUR CET QUIPEMENT Velocity Wolff Mod le VEL71 T12 100W PREHEAT BIPIN banc seulement Velocity PLUS Wolff Mod le VLP71 T12 100W Bi Pin partie sup rieure seulement Heraeus E400 HPT ou Philips Mod le HPA 400 30s ou CosmoTech Mod le 23045 unit faciale D brancher l alimentation lectrique avant de nettoyer l appareil d en faire l entretien ou de changer les lampes 4 TEk Cet quipement doit tre mis la terre Ce produit est conforme aux normes de rendement pour les lampes solaires dans le documents 21 CFR partie ell s 1040 20 ANSI UL 482 CAN CSA C22 2 N 224 88465 iv Wed N AN Ka A l E Unpacking and Inspection Your sunbed comes in two cardboard car tons one for the canopy and one for the bench and ballast tray Open the cartons and remove the sunbed parts as follows The boxes dismantle to allow easy removal of the units Remove the box tops and pull the sides out The bench and canopy are each wrapped in plastic Remove the plastic and with a helper or two grasp the canopy and pull it from the carton bottom without using the plastic endcaps to lift the unit Do the same for the bench Do not attempt to lift either unit with the plastic still on as it may slip The ballast drawer is secured to the carton bottom with brackets Remove these brackets from the ballast dr
31. s not replace old lamp NOTE Gas springs are manufactured to hold the canopy in its fully open position as well as allow it to rest fully closed If left open for an extended period of time some creep down may occur This is considered normal Keep the unit closed when not in use If the canopy will not stay fully open when raised Raise and lower the canopy a few times to lubricate gas spring internal seals Replace gas springs Face tanner operation is initially delayed by 5 seconds Face tanners will not relight for 1 minute if turned off Replace face tanner lamp see Removing Replacing Face Tanner Lamp If the timer button has been pressed to decrease tanning time during the session the time expired in the current minute is subtracted from the last minute By holding the body fan button for 3 seconds the timer display will briefly display three numbers the installed timer software version a factory set timer code and then the sunbed s id number 24 Je yy ASE Troubleshooting e Problem Solution Timer display is indicating Er 91 Timer software error Disconnect and reapply power to the unit Timer display is indicating Er 92 Current sensor indicating unit is off when it should be on Contact servicer Timer display is indicating Er 93 Current sensor indicating unit is on when it should be off Contact servicer Timer display is indicating Er 94 Requested session time exceeds maximum time allowed Time
32. should therefore be reduced by approximately 10 during that period WARNING Read the instructions booklet before using this sunlamp product All persons in the room should wear protective eye wear when lamps are on Required eyewear Ultra SunGlobes special eyez or other dark tinted eyewear that meet 21 CFR 1040 20 guidelines Other types of eyewear may not provide adequate protection Failure to use protective eyewear may result in severe burns or other eye injury If discomfort develops discontinue use and consult a physician ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT Velocity Wolff Model VEL71 T12 100W PREHEAT BIPIN Bench lamps Velocity PLUS Wolff Model VLP71 T12 100W Bi Pin Canopy lamps Heraeus E400 HPT or Philips Model HPA 400 30s or CosmoTech Model 23045 SolarMax IFT facial unit DISCONNECT POWER BEFORE ATTEMPTING TO CLEAN RELAMP OR ENGAGE IN THE MAINTENANCE OF THIS PRODUCT THIS EQUIPMENT MUST BE EARTH GROUNDED This product is in conformity with performance standards for sun lamp products under 21 CFR PART 1040 20 and ANSI UL Standard 482 Certified to CAN CSA Standard C22 2 NO 224 WTERTEX LISTED ill 88465 VLO 8 627 27938 01A Renseignements sur la S curit D ANG E R Rayonnement ultraviolet Veuillez suivre les instructions Evitez une exposition excessive Tout comme pour les rayons du soleil une exposition excessive peut causer des blessures aux yeux
33. t is running The arrow on the filter should point down Put the Front Access Panel in place and lock with the Access Panel Key Note You may have a few extra screws left over FILTER ACCESS PANEL 11 VIO 8E6L7 27938 01A Remote Connections Your sunbed incorporates advanced cir cuitry allowing itto connect and commu nicate with most remote control systems If a remote system is to be used first determine whether the remote system is a T Max System or a standard remote sys tem operating with a control relay The following pages outline many different remote connection scenarios Find the scenario that best fits your application Three remote ports are located on top of the ballast drawer at the front two RJ 22 4 wire ports and one RJ 11 6 wire port A Remote Control Bypass plug is already installed in one of the RJ 22 remote control ports Your sunbed will not operate without the Remote Control Bypass plug or a remote system connected ATTENTION Although the Remote Control Bypass plug provided with your sunbed will work wherever a T Max ter minator is called for in the series the T Max terminator will not work as a bypass plug Normally a bypass plug is needed only when your sunbed is operat ed without a remote system connected Installation Remote Connecti aie NSLALLALLON 171010 CONNECTIONS PE You will notice some wire clamps along the side of the fan housing under the benc
34. use Only one pair of eyewear is included A DANGER Some medication may increase your sensitiv ity to ultraviolet light It is recommended that you consult a physician before using this sunbed if taking any medication or if you sus pect that your skin might be especially sensi tive to sunlight DANGER Shock hazard Do not operate this device near water or while you are wet Exposure Times Follow the guidelines for skin type and exposure times as shown in the table below Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once a day Tanning normally appears after the first few sessions and maximizes after approxi mately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 20 MINUTES Level 1 Week 1 1st 3rd Sessions Skin Type Sensitive Skin Burns easily and severely and does not tan Light Ill Normal IV Dark Burns easily and severely and tans minimally Burns moderately and tans average Burns minimally tans easily and above average 17 Level 2 Level 3 Level 4 Level 5 NOT RECOMMENDED FOR TANNING 12 16 20 10 15 20 20 12 16 20 20 VIO 8E6L7 27938 01A Using Your Sunbed N Operation Using Your Sunbed NR MX 9
35. y Procedures a Install Gas Springs 1 Screw the upper Clevis Forks onto the Gas Springs piston end up as shown 2 Have a helper hold the canopy in its fully open position 3 The lower clevis forks are already installed Make sure the threaded hole faces up slide the Gas Springs down into the bench uprights and twist the Gas Springs into the lower clevis forks Turn the Gas Springs until they are snug Do not lower the canopy yet V10 8 6 7 27938 01A RY Ly Installation Assembly Procedures A 1 Attach Gas Springs 1 With the canopy still raised slip the Bronze Bushings into the hole in the clevis brackets on the underside of the canopy mounting arms 2 Line up both Clevis Forks and careful Clevis Bracket ly lower the canopy to engage the Clevis Forks Pay special attention when lowering the canopy that the clevis forks do not damage the bronze bushings Bronze is excel lent for smooth pivoting applica tions such as this but tends to be soft compared to the steel clevis fork 3 Lock the Clevis Forks in place with the Clevis Pins 4 Secure the Clevis Pins with the Retaining Rings NOTE When this assembly is complete lift and lower the canopy a few times to lubricate the gas springs for optimum per formance M Ng SP Installation Assembly Procedures RE Install Endcaps NOTE This unit comes with a foot end body fan I
Download Pdf Manuals
Related Search