SALTAS Manual - International Catering Equipment
Contents
1. 77777772 ej amp A Sern WG SOs on This instruction offer the information about kinds of fan cooling upright series fan cooling display series and worktable series Please note the contain in this instruction follow and execute each step in order to keep the refrigerator in the best situation Product transport and install e Transport During loading and delivery refrigerators cannot be reverse or lying down The angle that between product and ground must equal or more than 45 degree Please remark to put vertically for 2 hours after transport when your first time turn on the refrigerator Removal of redundant refrigerators Please ensure that old or redundant refrigerator and equipment are disposed of safely and legally We recommend that the first step is the door must be removed to ensure safety Unpacking Remove all external and interior packing and accessories ensure all such material is disposed of safely Ventilation It is essential to ensure that the room in which the unit is to be install has adequate ventilation just because the refrigerator generate a considerable amount of heat If operated in a small unventilated room in warm weather these will quickly cause the room temperature to become excessive This could cause the compressor to overheat and possibility damage the coil also make refrigerators consume large energy 500 600L model u2. Specific features please refer to the controller user manual Display code and function specification Specific features please refer to the controller user manual Initial operation and standby swith Specific features please refer to the controller user manual The controller maintenance reminder specification Maintenance reminder light To prevent compressor overload to remind the user timely maintenance of refrigerators to ensure the refrigerator normal operation When the compressor run time out maintennace reminder light is on The compressor will be protected by the controller program and automatic operation to keep the refrigerator refrigeration When the cabinet temperature reaches the set value the light go out automatically The following reasons maintenance reminder light will turn on 1 The door open frequently cabinet temperature can not reach the set value for a long time resulting in the long running of the compressor 2 Condenser dust resulting in poor cooling effect Please clean the condenser 3 Plastic door seals dosed not tight or the door is not closed Please ensure that the door is closed and the door seals closed tightly If you find that door seals is damaged please replace in time 4 Store too much or placed irregular obstruct cool air circulation 5 Store high temperature goods lead to the long running of the compressor Please remark do not put the high temperature goods into cabinets 6 Defor
3. Tel Maintenance g department keep Address Maintain Replace Machine Part Register Card Year Month Day Breakdown Name of replace parts Quantity Maintain Fee Client Signature
4. service engineer When you call the service engineer please tell us the model and serial number what write down on the nameplate This will use all spare parts safely and legally If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard Daily use 1 This product should not be use by the person who is physically weak or slow response and children Unless under the instruction or help ofhis or her responsible guardian 2 Children should be supervised to ensure that they do not play with the product 3 If the power cord is damaged it must be changed by the manufacturer maintenance department or related professional person 4 This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use ofthe appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance 5 The climate type of refrigerator is the sign of the cooling performance of the refrigerator while seasonal changes Our refrigerator meets the requirements of 5 T Climate type that means our refrigerator can use in temperate environment the environment of the Sub temperate subtropical environment and tropical environment 6 Using the rap wipe r
5. cuit diagram Br Temperature ggl Detect Switch Bo El Thermal Protector i o oU E 88 142 312 55 E 385 2 2 r Compressor 208 3 5 223 a e 823 F zur 28 2 Ei 29 gt J s E so 3 lt 3 Temperature Detect Switch Woz sas i88 om Compressor E 208 28 F 525 gs BE a 9 a Grounding EN J Note circuit diagram is stick on the product if some modify of the circuit diagram all subject to the diagram which stick on the product Warranty Card Model specification Address of purchase Date of purchase LL Invoice number Serial number Warranty period Name of client Tel LLL Client keep Address I After you purchase our product place fill in and send it back to our factory 2 Once you purchase one and your product have a one year guarantee Once the wwarranty card is lost ortear down by yourself the fee of maintain should not be include the guarantee service 3 The situation that product need to be maintain when exceed the time limit of the warranty card it the accessory can be retrieved the fee of maintain will be cheaper 4 The compressor that import from foreign break down is not included in the range of guarantee Warranty Card Model specification Address of purchase Date of purchase LL Invoice number Serial number Warranty period Client name
6. efrigerators with water warm water is the most suitable Avoid rinsing refrigerator with water directly especially the worktop Otherwise it may cause electrical short circuit resulting in security incident Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU To prevent possible harm to the environment or human health from uncontrolled waste disposal recycle it responsibly to promote the sustainable reuse of material resources To return your used device please use the return and collection systems or contact the retailer where the product was purchased They can take this product for environmental safe recycling Common fault and How to deal breakdown Breakdown Compressor Reason Voltage too low Breakdown Contain of inspect Inspect the voltage Inspect the circuit How to deal with it Add a power regulator Inspect by multimeter Compressor power off Inspect the power line Change or remove it Electric source break down Inspect the thermostat Change mdi Motor s winding of compressor Inspect the machine winding Change break down Moveable parts of compressor is blocked Inspect the compressor Repair or change can not stop Compressor Temperature Detector of controller wrong place Controller breaking down Refrigerant is not enough or leaked Freei
7. ng tube blocked Inspect the temperature detector whether on the probe clip Inspect the controller Inspect the freezing situation Inspect the freezing and filtrate temperature Adjusted and fixed the location ofthe detector Change Looking for the point for leaking reweld it or add the refrigerant Renew the filter and add refrigerant Freezing fan cooled machine dose not work Inspect the fan cooled machine and its circuit Change the fan cooler machine and inspect the circuit Compress with low efficiency or could not exhaust Inspect the quality of compressor Change one High frequency of opening door Open the door less Too many thing in the box and bad ventilation Too many dirty oil in condenser Door seal leak air to outside Environment temperature is too high Inspect the quantity things in the box Inspect the condenser Door seal Inspect the environment temp erature is above 32 degree or not Reduce the amount of thing in the box Clean the condenser Maintain and change door seal Improve the situation of ventilation or lower the environment temperature Preset temperature is too low Inspect the preset temperature Reset Too much noise The situat The ground is not horizontal Inspect the situation of under refrigerator Replace Capillary tube crash some small accessory Inspect capillary tube crash the small accessory or not Clean
8. our and then turn on the switch e Connection to main drains If installing a new refrigerator please ensure that it is connect to main drains e Shelf capacity distribution Before you put the food into refrigerator please open the refrigerator and reach normal operating temperature Please keep the food evenly distributed while you store it can ensure the cool air circulate to make the average temperature within the refrigerator Raw and cooked foods need to be kept separate e Door lock device About some models with a door lock it is recommended that the key be removed from lock during normal working use This will prevent bending and breaking of the key which could result in the lock having to be replaced Removing the key will also prevent any possibility of accident locking when the door is open This will prevent the door from closing non completely and will cause the interior temperature to rise If not checked in time may waste food Thermostat Panel Button function 3 amp Compressor running indicated light Page up key Page down key Code setting key press slightly enter setting temperature press for five second enter the code setting Mains switch key press slightly mean power on press for five second mean ON OFF Power off amp Motor running indicated light when it is on the motor is running Defrost indicated light when it is on the refrigerator is automatically defrost
9. st not completely will obstruct the evaporation duct lead to the long running Please defrost manually in time Controller wiring diagram Daily maintain Allthe maintain is responsible for our professional stuff we advice that daily maintain that should be responsible for a professional maintenance man to keep your refrigerator in a best time Cleaning Exterior If you clean the exterior ofrefrigerator using the correct way frequently it will retain an As new for many years We suggest to clean the exterior using a soft cloth and soapy water every day and wipe the refrigerator according to the texture of the stainless steel Although stainless steel is a very strong and durable material but not wipe according to the texture of the stainless steel will damage the smoothness ofthe exterior affecting the appearance Do not use abrasive cleansers and chemical cleansers this will damage or corrode the exterior ofthe refrigerator Protect the appearance of the refrigerator it is recommended that wiping use a professional stainless steel care solution occasionally Interior Cabinet must be cleaned regularly using a soft cloth and soapy water As far as possible remove all shelves support strip shelves and drawers Door seal clean and replace Remove the door seal and clean it and then put the seal in the middle of groove and pressed every corner press the seal into the groove in the end example Figure 3 If
10. sually generate 1200W heat 900 1200L model usually generate 1800W heat and 1500 1600L model usually generate 2400W heat while running These figures are approximate In addition to ventilation in a room please ensure that refrigerator placed at the top of the refrigeration system have 500mm distance between top of refrigerator and the ceiling for engineer access and ventilation For all other refrigerators please ensure a minimum adequate distance of SOmm is provided around the unit efficient and effective performance Do not block vents by stacking boxes on top or in front of unit as this could affect performance e Leveling Castors Feet The refrigerator should stand level to ensure correct operation of self closing doors and proper drainage of condensate from the evaporator The refrigerator has assemble unified castors cannot be adjusted therefore must be placed in the same horizontal plane Pressed the brake ofthe castors down to fixed refrigerator When you want to move the refrigerator please remark to release the brake first For the refrigerator with bullet foot to strike a balance by adjusting the bottom ofthe foot e Mains connection Please use the professional plug with a grounding function to ensure safety If you find any damage of plug and power cord it is recommended to contact us to replace parts If refrigerator 1s tipped over or reverse please don t turn on the switch immediately Put the refrigerator vertically for one h
11. the door seal has been damaged or magnetic disappear it need to replace the door seal mu BE LE p ff Figure 3 Condenser Cleaning The condenser is a part of refrigeration system and placed in the system It need to be cleaned approximately 6 times per year or be cleaned every month while usingin a dusty environment Disconnect mains supply before staring and use a hard brush wipe the condenser s blade vertically Please remark do not damage the blade or introduce any dust or dirt Ifthere are some dust or dirt on the blade please clean with a vacuum cleanr Reconnect mains supply while cleaning is finished Take care not to damage any electrical connections and cables during the removing and cleaning time After cleaning put all parts back in place and reconnect mains supply The condenser cleaning of worktable series products have some different from the others series like figure 4 The first is to loosen the screws outside the door of mechanical room remove the door of mechanical room The second loosen the screws on the pallet to pull the compressor outside the mechanical room The third clean the compressor and the condenser easily And the last step installed the compressor back according to the original step Evaporator Drain Periodic inspection to en sure drain hole is not block Break down In the event of a breakdown please check the controller setting and fuse before calling
12. up the tube Fan cooled machine break down Fan cooled machine quality Maintain or change Condenser or lamina of motor inside blocked Spring in compressor drop The screw of compressor fan cooled machine condenser loosed ion below is not broke down Fan cooled lamina Sound cause by crash from the machine Remove the touching thing Change the compressor Inspect the screw Screw down the screw 1 lower sound like stream sound when the refrigerator working 2 compressor and condenser got not 3 when the environment is too high and condense some bead outside the refrigerator please wipe it up Worktable with monobloc system for evaporator series The following operation is allowed only by professional maintenance staff perform How to remove the monobloc system for evaporator The first step disconnect the power The second step loosen and remove cord to prevent electric shock danger the two screws fixed on the chassis brace The third step put the system out for 400mm press and hold the connection The fourth step remove the monobloc terminal as shown system and put down near the worktable Circuit diagram 1 Fan cooling system worktable series circuit diagram Temperature Detect Switch Thermal Protector Microcomputer Digital Display Thermostat JSMojg BulAesodeag 2 Single door fan cooling system upright series cir
Download Pdf Manuals
Related Search