Sound-Sensor Nursery Monitor
Contents
1. CH windows Lid of the DC IN 9V jack DCIN 9V jack CHARGE indicator CH selectors Rear Belt clip Cavity for hook VOL To a wall outlet gt AC adaptor Na To a wall outlet lt BP TR10 battery pack The attached packing is used to ensure water resistance of the battery compartment Therefore make sure to close the battery compartment lid securely AC adaptor s 7 Battery wires IN 9V jack CHARGE indicator Cavity for hook Cavity for hook Belt clip Cavity for hook Power Sources See Fig EN Connect the supplied AC adaptor to the DC IN 9V jack and plug it in to a wall outlet Receiver To operate on battery See Fig EJ T Turn the tab of the battery compartment lid at the rear of the receiver to the OPEN position with a coin Pull the depressions on both sides to open the lid 2 Connect the battery connector to the battery terminal with correct polarity Black wire goes on the left side and red wire goes on the right side 3 Insert one rechargeable battery pack BP TR10 supplied into the battery compartment Make sure the battery wires are positioned properly so that the wires are not pushed out of the compartment when closing the lid 4 Close the lid then turn the tab to the LOCK position with a coin Note When operating the receiver on a rechar2. Any parts or product replaced under this Limited Warranty will become the property of Sony This Limited Warranty only covers product issues caused by defects in material or workmanship during ordinary the Sony product or product purchased from other than Sony or a Sony Retailer To determine if a retailer is part of the Sony Retailer Network please contact Sony s Customer Service Call Center or go to www sony com support This Limited Warranty does not cover Sony products sold AS IS or WITH ALL FAULTS or consumables such as fuses or batteries This Limited Warranty is invalid if the factory applied serial number has been altered LIMITATION ON DAMAGES SONY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DURATION OF IMPLIED WARRANTIES EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY Some states do not allow the exclusion or limitation of incidental or consequential damages or allow limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you This Limited Warranty gives you specific legal rights and you may have other rights which vary from state to state SA RR RRR RER RRR E N XS an se ao Portable Audio ZZ R se inst defects in material or workmanship for the time om Sony or a Sony Retailer Pursuant to
3. uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help If you have any questions about this product you may call Sony Customer Information Services Center 1 800 222 7669 or http www sony com Declaration of Conformity Trade Name SONY Model NTM 910 Receiver unit Responsible Party Sony Electronics Inc Address 16530 Via Esprillo San Diego CA 92127 USA Telephone Number 858 942 2230 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation OR ia 3 os ia
4. R R 7 E RE E E ee ee ee EENE EDE EEN EEN ENEI 3 ve E A rer SONY X SRI OO RoR RS ENK Sony e E es nS RIS BS Z ee X Sony Electronics Inc Sony warrants this product agai periods and as set forth below when purchased directly fr AR LIS X ORR es edies DODO E Term For a period of one 1 year from the original date of H X X OR ees BK Se This Limited Warranty covers only the hardware compo Se technical assistance for hardware or software usage and it eS Se rights and obligations with respect to the software It is your responsi product The Address of the Laredo Fulfillment Center is Laredo Fulfillm 10227 Crossroads Laredo TX X Z w X Be SPRY RS OR BMS K For an accessory or part not available Bes 1 800 488 SONY 7669 Repair Replacement Warranty This Limited Warranty i BRAD OER SAS g See X oo consumer use it does not cover product issues caused by issues due to commercial use acts of God misuse limitati D S BK X Ree SS RK ZRO RORE X or removed from the product This Limited Warranty is val DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED SOR y ne DY OR AEE EEN OR OR ROR RR SOR RRR OR NEN N ESR SR SR OR SRR ORR Ne ee One ee BS RT RR A OBITE E E a A E MEN LIMITED WARRANTY wus or Warranty Sony will at its option i repair the product using
5. SONY 3 242 835 25 1 Sound Sensor Nursery Operating Instructi NTM 910DU 2007 Sony Corporation http www sony net Monitor Ons a Ul Printed in China 32428352 5 1 For customers who purchased this product in the USA Please register this product on line at http www sony com productregistration Proper registration will enable us to send you periodic mailings about new products services and other important announcements Registering your product will also allow us to contact you in the unlikely event that the product needs adjustment or modification Thank you To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture STRANGULATION HAZARD To prevent cord entanglement and strangulation Do not place transmitter or cord within reach of children Do not place transmitter or cord in or attach to crib or playpen Never use extension cords with AC adaptors Only use AC adaptors provided You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates
6. attery compartment as follows Open or close the battery compartment with dry hands in a place without exposure to any water Wipe off the battery and the inside of the battery compartment Give special attention to the contacts so that no water remains on them Troubleshooting Should any problem persist after you have made the following checks consult your nearest Sony dealer No sound even with both units turned on e AC adaptor is disconnected from the wall outlet Battery is used up Receiver is too far from the transmitter e CH selectors of both transmitter and receiver are not on the same settings Too much noise Weak battery Receiver is too far from the transmitter e Interference from another electrical appliance Turn off the appliance or move it further from the receiver Weak reception Receiver is too far from the transmitter MONITOR indicator is not lit Weak battery Receiver is too far from the transmitter Buzzing interference e Another transmitter interfering Set the CH selectors of both the transmitter and receiver to another setting Shrill noise Receiver is too close to the transmitter Volume is too high Alarm continues to sound although the distance between the transmitter and the receiver becomes within operating range e Transmitter is not set to ON CH selectors of both the transmitter and receiver are not on the same settings
7. e e e Specifications Frequency range 902 200 904 900 MHz Number of channels 27 channels Modulation system FM Transmitter Circuitry Crystal controlled PLL circuit Power requirement AC adaptor DC IN 9 V jack 120 V AC 60 Hz Dimensions 101 8 x 99 5 x 63 mm w h d 4 1 s x 4 x 2 1 2 inches not incl projecting parts and antenna 101 8 x 140 5 x 63 mm w h d 4 1 s x 5 5 8 x 2 1 2 inches incl projecting parts and antenna Mass Approx 128 2 g 4 5 oz Receiver Circuitry Single superheterodyne Power requirement AC adaptor DC IN 9 V jack 120 V AC 60 Hz 2 4 V DC Rechargeable battery pack BP TR10 Audio power output 110 mW using the supplied AC adaptor 40 mW using 2 4 V DC Speaker 57 mm dia 16 Q Dimensions 94 x 109 x 59 mm w h d 3 3 4 x 4 s x 2 3 s inches not incl projecting parts and antenna 94 x 157 x 59 mm w h d 3 3 4 x 6 1 4 x 2 s inches incl projecting parts and antenna Mass Approx 184 3 g 6 5 oz Approx 228 8 g 8 1 oz incl a rechargeable battery pack Supplied accessories AC adaptor 3 Rechargeable battery pack BP TR10 2 Design and specifications are subject to change without notice Transmitter DCIN 9V jack Antenna Built in microphone POWER indicator OFF ON switch CH windows CH selectors Receiver Front Antenna MONITOR indicators POWER BATT indicator RANGE ALM indicator OFF ON VOICE ACT switch Speaker
8. er is not loud or all the indicators may light up if the sound is very loud You can also hear sounds through the speaker To adjust the volume The volume of the sounds you receive varies depending on the loudness of the baby s voice distance between the transmitter and the baby direction of the built in microphone of the transmitter obstructions etc Set the volume as required using VOL If the volume level is set too high and is accompanied by a shrill noise reduce the volume The volume level can be adjusted between the smallest and biggest dots on the VOL Notes e Avoid placing the units near heat sources or where they are subject to direct sunlight excessive dust moisture or mechanical shock e Be careful not to drop the receiver in water or drop any liquid over it Do not use the antenna as a carrying handle Do not use the antenna to hang the receiver on the wall Be sure to use the cavity for hook Using Belt Clip See Fig 9 The receiver has a belt clip located on the rear It is convenient when you move around for example when you clean up the room etc Insert your finger into the cavity for hook and slide upwards as illustrated then hang the belt clip onto your belt When fixing the receiver onto your belt be sure to turn off the receiver and disconnect the AC adaptor from the DC IN 9V jack and the wall outlet Then close the lid of the DC IN 9V jack securely Notes When usin
9. g the belt clip the receiver can be operated only on battery When you are not using the belt clip push it back to its original position e Make sure that you do not move outside the effective operating range of the system
10. geable battery pack make sure that the lid of the DC IN 9V jack of the receiver is closed securely to ensure water resistance of the receiver Battery life approx hours for continuous standby JEITA Sony rechargeable battery pack BP TR10 22 Measured by JEITA Japan Electronics and Information Technology Industries Association standards The actual battery life may vary depending on the circumstance of the unit When to recharge the rechargeable battery pack If the sound becomes distorted or interrupted we recommend that you recharge the battery pack When the battery pack is used up the POWER BATT indicator starts flashing and the receiver sounds a beep If the battery pack is extremely used up the beep may be interrupted or the POWER BATT indicator may flash when you turn on the power Recharge the battery pack as soon as possible in either case Recharge the battery pack for more than 22 hours so that the battery pack is fully charged Turn off the receiver before charging the battery pack The CHARGE indicator remains lit even after charging has been completed Charging duration Approximately 22 hours are required to charge the battery pack to its full capacity Notes on the rechargeable battery pack e The battery pack will gradually discharge over a long period of time even if not in use If you leave the weak battery pack inside the receiver without charging it the battery pack will be completely discha
11. hat you check the operating range and condition of the Sound Sensor Nursery Monitor on initial installation and on a regular basis after that Stay close to the receiver in order to hear normal sounds from it Check the volume regularly to ensure that it is set high enough Recharge the rechargeable battery pack in the receiver or operate it on house current as soon as the POWER BATT indicator starts flashing and the receiver sounds a beep The receiver can be affected by other devices in or near your home that may interfere with the signals sent by the transmitter Such interference can be caused by TV sets cordless phones vacuum cleaners car ignitions and other electrical devices You should test the receiver when you expect such devices to be in operation while you are using the Sound Sensor Nursery Monitor The signal from the transmitter can be received by another receiver as it uses a public air wave Cautions on Water resistance for the receiver only This unit is designed so that it can be used with slight exposure to water rain snow and other forms of moisture but there are several points on which caution should be observed Do not allow it to come into contact with large amounts of water Do not immerse it in water If water should get on it or if it should fall into water take it out immediately and wipe it off with a dry cloth To prevent the battery from corroding wipe out the interior of the b
12. indicators allow you to know the operating condition of the receiver Water resistance allows operating the receiver in slight moisture areas such as kitchen or bathroom Operating on rechargeable battery pack Precautions Safety Precautions Operate the transmitter and receiver on 9 V DC To operate them from a house current use only the supplied AC adaptor do not use any other type For battery operation of the receiver use one rechargeable battery pack BP TR10 Should any solid object or liquid fall into the unit disconnect the AC adaptor and remove the battery and have the unit checked by a qualified personnel before operating it any further e If you are not going to use the system for a long time Disconnect both transmitter and receiver from the wall outlet by pulling out AC adaptors Remove the battery out of the receiver to avoid damage from battery leakage If you have any questions or problems concerning your system please consult your nearest Sony dealer Precautions on Usage This product cannot replace responsible adult supervision of a child It is designed to assist adults in child supervision Do not use it for medical monitoring of a sick baby or child The transmitter detects normal sound levels within a range of 2 to 3 meters 6 to 10 feet from a child If the child moves outside of this range it may not be able to detect sounds from him or her It is essential t
13. new or refurbished parts or ii replace the product with a new or refurbished product For purposes of this Limited Warranty refurbished means a product or part that has been returned to its original specifications In the event of a defect these are your exclusive rem or replace with new or refurbished product or parts any product or parts determined to be defective contained in the Product any such software is provided AS IS unless expressly provided for in any enclosed software Limited Warranty Please refer to the End User License Agreements included with the Product for your Instructions To obtain warranty service you must deliver the product freight prepaid in either its original packaging or packaging affording an equal degree of protection to the Sony authorized service facility specified ibility to backup any data software or other materials you may have stored or pre served on your unit It is likely that such data software or other materials will be lost or reformatted during service and Sony will not be responsible for any such damage or loss A dated purchase receipt from Sony or a Sony Retailer is required For specific instructions on how to obtain warranty service for your Visit Sony s Web Site www sony com support Or call the Sony Customer Information Service Center 1 800 222 SONY 7669 ment product for the remainder of the original Limited Warranty period or for ninety 90 days whichever is longer
14. of children Do not place transmitter or cord in or attach to crib or playpen Never use extension cords with AC adaptors Only use AC adaptors provided e Position the transmitter with the front side where the built in microphone is located facing the baby Do not use the antenna as a carrying handle Do not use the antenna to hang the transmitter on the wall Be sure to use the cavity for hook Monitoring through the receiver See Fig 9 6 The longest distance you can place the receiver from the transmitter varies according to obstructions and other conditions First test the operating range with the assistance of another adult or by placing a radio etc near the transmitter If you move outside the effective operating range of the system the RANGE ALM indicator lights up and the buzzer sounds In such a case move closer toward the transmitter until the indicator and the buzzer turn off Tips for better reception e Keep the receiver upright during operation e Make sure that nothing touches the antenna during operation The VOICE ACT function eliminates most background noise when the receiver does not detect any sound Set the OFF ON VOICE ACT switch to VOICE ACT to turn on this function When the receiver receives sounds from the transmitter the MONITOR indicators light up from left to right in five steps depending on the sound level Only one indicator may light up if the sound from the transmitt
15. rged It may require several times of charging to recover to its full capacity Notes on replacing the rechargeable battery pack If the battery pack lasts only a few minutes even after 22 hours of charging the battery life has expired and needs replacement Before replacing the battery pack make sure that the receiver is turned off Replace the battery pack with a new one Contact your local Sony authorized dealer or service center and ask for a Sony BP TR10 rechargeable battery pack Do not use any other rechargeable battery pack To operate on house current See Fig EJ Open the lid of the DC IN 9V jack of the receiver Connect the supplied AC adaptor to the DC IN 9V jack and plug it in to a wall outlet The CHARGE indicator will light up whether or not the receiver is turned on Notes on AC adaptor When the AC adaptor is not used be sure to turn off the receiver and unplug it from the DC IN 9V jack and the wall outlet Then close the lid of the DC IN 9V jack securely Use only the supplied AC adaptor Do not use any other AC adaptor Replace the AC adaptor with the same type as the one supplied if replacement is necessary Polarity of the plu A go y plug Setting Up Turning on the power Set the OFF ON switch of the transmitter and the OFF ON VOICE ACT switch of the receiver to ON to turn on the power The POWER indicator of the transmitter and the POWER BATT indicator of the recei
16. this Limited purchase of the product Sony will at its option repair nents packaged with the Product It does not cover does not cover any software products whether or not ent Center Loop Suite B 78045 from your authorized dealer call shall apply to any repair replacement part or replace any other reason including but not limited to product ions of technology or modification of or to any part of lid only in the United States WARRANTY ON THIS PRODUCT Bees ES oo nee eae oer eae ee Bee oa rE SES RSS xv D45571460 RECYCLING NICKEL METAL HYDRIDE BATTERIES Nickel Metal Hydride batteries are recyclable You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you For more information regarding recycling of rechargeable batteries call toll free 1 800 822 8837 or visit http www rbrc org Caution Do not handle damaged or leaking Nickel Metal Hydride batteries Before You Begin Thank you for choosing the Sony Sound Sensor Nursery Monitor Before operating the Sound Sensor Nursery Monitor please read these instructions thoroughly and retain them for future reference Features Up to 27 channels for maximized reception Voice Activation eliminates most background noise for a more peaceful sleep e 5 indicators for monitoring sound levels RANGE ALM POWER BATT and CHARGE
17. ver will light up To turn off the power set the OFF ON switch of the transmitter and the OFF ON VOICE ACT switch of the receiver to OFF Setting the frequency channels Up to 27 channels can be set through the CH selectors by changing the combination of three colors red yellow and green on the CH windows Set the CH selectors of both the transmitter and receiver so that the settings of color combinations shown in the CH windows are the same Otherwise the transmitter and receiver will not function If the settings of the receiver and transmitter are not the same the RANGE ALM indicator starts flashing and the receiver sounds a beep If signal interference occurs Set the CH selectors of both the transmitter and receiver to another setting Make sure that both the settings shown in the CH windows are the same Setting up the transmitter See Fig Place the transmitter within 2 to 3 meters 6 to 10 feet from a crib or play area If the child moves outside of this range the transmitter may not be able to detect his her sounds The transmitter must be placed upright during operation Tips for better reception e Place the transmitter at a location as high as practically possible such as on a table or on a wall e Make sure that the transmitter is not covered or obstructed for picking up sounds Make sure that nothing touches the antenna during operation Notes e Do not place transmitter or cord within reach
Download Pdf Manuals
Related Search