Blu-ray/DVD/CD Duplicator Control Manual User`s Manual
Contents
1. press ENT to confirm 8 9 5 CD Overburn Allows the copying of CDs that have been burned over their maximum capacity The target disc s must be the same capacity as the master disc Press ENT or to select mode and press ENT to confirm 8 9 6 Show HDD Image Allows the option to display the name of the HDD image name default or the image size in MB or to select Image Name Capacity and press to ENT confirm Press ENT 8 9 7 Keep Buffer You can set Yes to load source disc to buffer in first round of Copy Test Compare or Copy Compare and do it again without the source disc Or set No to keep buffer not be used Note The source will be only temporary saved in buffer there will be nothing left when you exit the task Copy Test Compare and Copy Compare or reboot the system 8 9 8 Boot Password Sets password protection for the duplicator before the boot up process can be started The boot password prevents anyone unauthorized from using the duplicator system Press ENT or to select mode and press ENT to confirm If Disable is selected no password will be set and the display will direct back to the Setup sub menu If Enable is selected a password must be entered using the following guidelines Use or to select the character desired Press ENT to go to the next position There are a total of 6 positions for the password To enable the password set all 6 positions For space press ENT without cho2. Blu ray DVD CD Duplicator Control Manual User s Manual 0 TABLE OF CONTENTS Introduction 2 Setup 12 HDD Manager 16 LCD Front Panel Overview 2 o Auto Start Time 12 o Select Image 16 Controller Connection 3 o Display Mode 12 o Disc gt Image 16 Menu Overview 3 6 o Button Beep 13 o Set Reader Speed 17 Functions 6 o Eject on Start 13 o Show Image Info 17 Copy 6 o Reader Speed 13 o Rename Image 17 Test 7 o Compare Speed 14 o Delete Image 18 Compare 7 Language 14 o Show HDD Info 18 Copy Comp 8 Clear Setup 14 o Format HDD 18 Set Burn Speed 9 Advanced Setup 14 Select Source 9 o Power On Time 14 Utility 10 o Start Up Menu 14 o Information 10 o Skip Read Error 15 o Erase Disc 10 o Change Bad Master 15 o Prescan 11 o CD Overburn 15 o Track Edit 11 o Show HDD Image Name 15 Basic Troubleshooting 18 19 o Eject All Disc 11 o Keep Buffer 15 o Copy Counter 11 o Boot Password 15 Specification of SATA Controller 20 o Update BIOS 12 o Setup Password 16 1 Introduction Thank you for purchasing the our SATA CD DVD Blu ray Duplicator Controller This controller is specifically engineered to run a stand alone CD DVD Blu ray duplicator without additional computer or processing unit With a simple four button interface and a LCD screen to displa
3. next position Press ENT to confirm There are 8 characters for each image name No empty space allowed in the image file name Press ESC to cancel the process 17 Press ENT 9 8 Format HDD Deletes and formats all image s on the HDD restores the HDD to factory defaults and initializes the HDD for use with the duplicator Press ENT Press ENT to confirm format Press ENT again to confirm and start formatting Basic Troubleshooting Follow these simple steps for quick and proper troubleshooting 1 Power does not turn on or unit receives no power a Check power cord and outlet to make sure power connections are secured b Check voltage switch on the back of the duplicator to make sure power supply is set for correct outlet rating c Test with another power cord same as a PC power cord to eliminate cable failure 2 Master disc cannot be read a Change the master disc The master disc may be of poor quality or with error s that can make duplication difficult or impossible b Remake the master disc on another disc Master disc may be of poor quality or with error s that make duplication difficult or impossible c Change the source drive to one of the other drives to test d Make sure the master disc is finalized in standard ISO format 3 High failure rate 18 a Change the media type Certain types of media may not be compatible with the drives Poor quality media can also cause high failure rate b Low
4. Track Allows the selection of individual track s from the master CD and copies the selected track s onto all target discs 7 4 2 Close Disc Closes the target discs when all of the track s are burned on to all target discs Note The copied disc s will NOT play back without this step Do NOT skip this step 7 4 3 Disc Info Displays the information regarding the track s on the disc s and how much space is remaining on the target disc s 7 5 EJECT ALL DISC Allows the duplicator to eject disc 7 6 COPY COUNTER Counts the number of successful and failed copies of CD DVD Blu ray made by the duplicator 7 6 1 Show Counter Show the number of successful and failed copies of CD DVD Blu ray 7 6 2 Enable Counter Set Enable or Disable the Copy Counter 7 7 6 3 Clear Counter To reset the Copy Counter 4 7 7 Update Bios Allows for update or rollback of the controller firmware SETUP 8 1 Auto Start Time Sets auto start time from OFF no auto start to 99 sec Allows the duplicator to automatically start one of six following functions once the master disc and desired number of target disc s are inserted and the drive trays are closed Copy Test Copy amp Verify Copy amp Compare Verify and Compare 8 2 Display Mode Sets the amount of information displayed on the LCD during the performance of various functions 8 2 1 Basic Basic Information Displays 8 2 2 Show Timer Enables or disables the copy time to
5. 3 Prescan 7 3 1 Prescan Prescans the master disc and verifies the integrity and quality of the master disc a Select Utility and press ENT to enter the sub menu b Select 1 Pre scan and press ENT Press ENT Finish Prescan 7 4 Track Edit 7 4 1 Copy Track Allows the selection of individual track s from the master CD and copies the selected track s onto all target discs 7 4 2 Close Disc Closes the target discs when all of the track s are burned on to all target discs Note The copied disc s will NOT play back without this step Do NOT skip this step 7 4 3 Disc Info Checks the capacity and space used on the disc s inside of the drive s of the duplicator 7 5 Eject All Discs Performs a simultaneous ejection of all of the optical disk drive s on the duplicator Press ENT Press ENT All disc trays will open 7 6 Copy Counter Tracks the numbers of successful and failed copies made by the duplicator for both CDs and DVDs There are three 3 parts of this tool Show Count to display current copy counter Enable Counter to turn the counter on or off and Reset Counter to clear counter 11 7 6 1 Show Counter Press ENT Press ENT 7 6 2 Enable Counter Press ENT Press ENT or and press ENT to select choice 7 6 3 Clear Counter Press ENT Press ENT Press ENT to confirm or press to ESC cancel 7 7 Update BIOS Updates the BIOS firmware of the duplicator controller
6. Press ENT Insert update CD and press ENT Update completed and eject disc Re boot system 8 Setup This command contains options to configure the duplicator system 8 1 Auto Start Time Set the amount of time before the duplicator will automatically start the selected command ranging from OFF no auto start to 99 seconds in 1 second increments 1 2 3 97 98 99 Press ENT or to select seconds and press ENT to confirm 8 2 Display Mode Changes the display readout during the performance of various commands Press ENT or to select mode and press ENT to confirm 12 8 2 1 Basic The Basic mode displays a progress bar along with the amount of total data in MB on the master DVD or in time for the master CD 8 2 2 Show Timer Allows the display of total time taken for the copy process to be complete Press ENT or to select mode and press ENT to confirm 8 2 3 Show Speed Displays the speed at which discs are read and writing during various processes 8 3 Button Beep Turns the audio signal a beeping sound ON or OFF for pressing of the buttons Press ENT or to select mode and press ENT to confirm 8 4 Eject On Start Allows the drive s with disc s present inside to eject the disc trays when the machine is done initializing or to select Eject All No Eject Eject Target Eject Source and press ENT to confirm Press ENT 8 4 1 Eject All Discs Performs a simult
7. aneous ejection of all of the optical disk drive s on the duplicator Press ENT All disc trays will open 8 4 2 Do Not Eject Do not eject any disc 8 4 3 Eject Target Only Eject writer drive only 8 4 4 Eject Source Only Eject reader drive only 8 4 5 Eject All Trays Eject all drives 8 5 Reader Speed Sets the reader speed for the duplicator to read the master disc s The speeds for CD are 1 2 4 8 10 12 16 20 24 32 36 40 44 48 52 56 default MAX The speeds for DVD are 1 2 2 4 4 6 8 10 12 16 18 20 default MAX or to select CD Read and press ENT Press ENT 13 or to select DVD read speed and press ENT to finish 8 6 Compare Speed Sets the speed at which the master disc is compared with the copies disc s The speeds for CD are 1 2 4 8 10 12 16 20 24 32 36 40 default 44 48 52 56 MAX The speeds for DVD are 1 2 2 4 4 6 8 12 16 default 18 20 MAX Press ENT or to select CD Compare Speed and press ENT or to select DVD Compare speed and press ENT to finish 8 7 Language Sets the language selection of the display Available languages are English default Spanish Portuguese and Japanese or to select language and press ENT to confirm Press ENT 8 8 Clear Setup Resets the duplicator controller back to factory default settings Press ENT to confirm Press ENT Press ENT to clear all settings 8 9 ADVANCED SETUP Thi
8. aster disc placed in the designated Source Drive to all target discs in the Writer Drives This process burns all information contained on the master disc to the target discs so the copies are exact duplicates of the master disc To Start the Copy Process 1 Power on the machine if not already on 2 Eject disc tray of the Source Drive and place the master disc in the designated Source Drive usually the top The master disc is the original of which copies are made 3 Eject disc tray s of the Writer Drives and place blank disc s on the tray s Number of drives used depends on number of copies desired It is not necessary to always use all drives 4 Use the scroll buttons to select the command 1 Copy and press the ENT button The drives will automatically close trays and begin the copy process 6 5 Once the copy process is completed the disc trays will eject and the display will read Copy Result Pass X Fail Y with X being the number of successful copies and Y being the number of failed copies To reduce copy failure please refer to the troubleshooting section of the manual Press ENT to load disc and execute Copy Analyze master disc Start copying Finish and eject discs 7 To start the Compare process please follow the instructions below 1 Power on the machine if not already on 2 Eject disc tray of the Source Drive and place the master disc in the designated Source Drive usual
9. be displayed when the copy process is finished 8 2 3 Show Speed Displays the speed at which discs are read and writing during various processes 8 3 Button Beep ON or OFF Beeping sound 8 4 Eject on Start Eject all trays after the booting sequence complete 8 4 1 Eject All Discs Eject all trays with disc inside 8 4 2 Do Not Eject Do not eject any disc 8 4 3 Eject target Only Eject writer drive only 8 4 4 Eject Source Only Eject reader drive only 8 4 5 Eject All Trays Eject all drives 8 5 Reader Speed Sets the speed at which discs are read during various processes 8 6 Compare Speed Sets the speed at which the compare process is executed 8 7 Language Allows different language selections for LCD display 8 8 Clear Setup Clears the CMOS and resets the duplicator controller back to factory defaults 8 9 ADVANCED SETUP 8 9 1 Power On Time Sets system warm up time from 5 sec to 99 sec Default is 15 seconds 8 8 9 2 Startup Menu Assigns a command to be displayed first after the duplicator has been initialized 8 9 3 Skip Read Error Enables the option to halt the duplication process if there is an error on the master disc Disables the option to allow the process to continue with the same errors as the master disc 8 9 4 Change Bad Master Disc Enables or disables changing of a master disc during the copy process when an error is detected on the master disc 8 9 5 CD Overburn Enables or disabl
10. ection is for audio CDs Use the Scroll buttons to select the desired burn speed and press the ENT button 5 The third speed selection is for DVDs Use the Scroll buttons to select the desired burn speed and press the ENT button Note The selection is only available on DVD duplicators 6 The last speed selection is for DVD DL Use the Scroll buttons to select the desired burn speed and press the ENT button Note The selection is only available on DVD duplicators or and press ENT to set general data CD burning speed Press ENT amp or or and press ENT to set audio CD burning speed Finish and return to main menu or and press ENT to set DVD burning speed 6 Select Source This command will allow you to change the source drive to any one of the drive s inside the unit including the HDD if installed To change the source drive inside the unit to a different drive 1 Power on the machine if not already on 2 Use the Scroll buttons to select the 6 Select Source Press the ENT button 9 3 The current Source Drive will be displayed along with the partial model number of the drive and the port number in brackets 4 Use the Scroll buttons to select from other available drives until the port number of the desired drive is displayed 5 Press the ENT button The desired drive will then become the Source Drive Press ENT Display current Source Drive setting or to select drive Pres
11. er the burn speed and attempt another copy process Lowering the speed increases the stability of the duplication process c Check for available firmware updates for the unit A firmware update may resolve any unspecified issues 4 Machine locks up during the copy process a Hold down the ESC button to abort the copy process The copy process will cancel and menu goes back to the last function executed b If the button cancel does not work power cycle the unit power the unit off leave off for five seconds and power the unit back on c Change the master disc A master disc with error s or a poor quality master disc can cause duplication to lock up at particular points during the copy process 5 Button s do not function on the unit a The duplicator may be busy Buttons pressed while the duplicator is processing will not perform functions unless otherwise specified b Possible faulty button Contact your technical support department for further information 6 One of the drives does not open and or LED does not light up a Check USB and or Firewire port switch and make sure the switch is in the OFF position before machine power is turned on b If a disc is stuck inside a drive insert a paper clip or safety pin in the pinhole underneath the drive door and push gently Make sure the power is OFF during this step Then press the EJECT button of the drive a few times to test the disc tray 7 The blank CD or DVD or Bl
12. es the duplication of overburned CDs 5 8 9 6 Show HDD Image Name Allows the image name to be displayed on the LCD screen when selecting the HDD as the source drive 8 9 7 Keep Buffer To set enable or disable load source to the buffer 8 9 8 Boot Password Sets password protection for machine boot up 8 9 9 Setup Password Sets password protection for changing setup options 9 HDD Manager The management for various functions of the hard disk drive HDD Functions Note For this function and submenu to be displayed a HDD must be installed in the duplicator 9 1 Select Image Selects an image file as a source to be copied to the discs 9 2 Disc Image Loads an image to the HDD from a master CD or DVD or Blu ray as an Image file 9 3 Set Reader Speed Sets the speed of data loading from the master CD or DVD or Blu ray to the HDD 9 4 Show Image Info Displays the image file information such as image order name file size and type of image 9 5 Rename Image Renames the HDD image partition name up to 8 characters 9 6 Delete Image Deletes an image file in HDD Note A file selected as the source file cannot be deleted until a different image is selected See 9 1 9 7 HDD Info Displays the information in HDD such as the number of discs stored on the HDD and the amount of space left in the HDD 9 8 Format HDD Formats the HDD erasing ALL data stored on the HDD 1 Copy This command will copy the m
13. ly the top The master disc is the original of which copies are made 3 Eject disc tray s of the Writer Drives and place copied disc s to be compared on the tray s Number of drives used depends on number of copies to be compared It is not necessary to always use all drives 4 Use the scroll buttons to select the command 3 Compare and press the ENT button The drives will automatically close trays and begin the compare process 5 Once the compare process is complete the trays will eject the discs that have passed the compare process 4 Copy amp Compare This command will perform the copy process and immediately follows with a comparison between the master disc and the copied disc s to ensure the copies are exact duplicates of the master disc This command is especially useful for DVDs data CDs and video CDs Note The Compare process is a bit by bit comparison between the master disc and the copied discs This operation ensures that all of the copies are completely identical to the Master disc This command is not applicable to audio CDs Finish and eject disc Start comparison To start the Copy amp Compare process 1 Power on the machine if not already on 2 Eject disc tray of the Source Drive and place the master disc in the designated Source Drive usually the top The master disc is the original of which copies are made 3 Eject disc tray s of the Writer Drives and place blank disc s on
14. mmediately follows the copy process with a bit for bit comparison between the master disc and copied disc s to ensure exact duplication Note The Compare function cannot be used with audio CDs 5 SET BURN SPEED Allows the speed settings to be changed for various formats 6 SELECT SOURCE Allows the source drive to be changed to any of the available drives in the duplicator including the Hard Disk Drive HDD UTILITY 7 1 INFORMATION 7 1 1 Disc Info Displays basic information of the discs inserted such as disc type amount of data on disc for master disc s in MB and media book type For blank media displays the media book type available space and speed of the media 7 1 2 Drive Info Displays information of all drives in the duplicator including the Reader HDD if present and Writer drive s 7 1 3 System Info Displays the duplicator controller information such as the hardware version buffer memory and currently loaded firmware 7 2 ERASE DISC 7 2 1 Quick Erase Erases all rewritable media CD RW DVD RW DVD RW DL BD RW 7 2 2 Full Erase Formats all rewritable media CD RW DVD RW DVD RW DL BD RW 7 3 PRESCAN 7 3 1 Pre scan Performs a scan on the master disc before the copy process starts and ensures the master disc can be copied in the duplicator 7 4 TRACK EDIT Allows for the selection of individual track s from different master audio CDs to create custom compilation 7 4 1 Copy
15. of which they were loaded Press ENT or to select image and press ENT to confirm 9 2 Disc gt Image Transfers the information from the master CD DVD Blu ray to the HDD After the image s transfer is complete the reader drive is ejected and the source drive is changed to the HDD The source disc loaded to HDD as image file A001 Press ENT 16 Note The Source Disc may be placed in the Reader Drive or any of the Writer Drives 9 3 Set Reader Speed Change the read speed load speed for the HDD The speeds for CD are 1 2 4 8 10 12 16 20 24 32 36 40 44 48 52 56 default MAX The speeds for DVD are 1 2 2 4 4 6 8 10 12 16 18 20 default MAX or to select CD Read Speed and press ENT to confirm Press ENT or to select DVD Read Speed and press ENT to confirm 9 4 Show Image Info Shows the image number in sequential order the file name of the image stored on the HDD the type of image stored and the amount of data the image contains in MB for DVD Blu ray or time for CD Press ENT or to select image and press ENT to display info 9 5 Rename Image Renames the image instead of using default file names A001 A002 etc Up to 8 characters DVD disc image of 3 875GB as file A001 CD disc image of 65 min 28 sec as file A003 Select the image file to be renamed and press ENT Press ENT or to select character Press ENT to go to the
16. osing a character to leave the position empty 15 Press ESC to cancel the process The duplicator will ask for password when the unit is restarted 8 9 9 Setup Password Sets password protection for the duplicator before the setup settings can be altered The setup password prevents unauthorized changes to the system Press ENT or to select mode and press ENT to confirm If Disable is selected no password will be set and the display will direct back to the Setup sub menu If Enable is selected a password must be entered using the following guidelines Use or to select the character desired Press ENT to go to the next position There are a total of 6 positions for the password To enable the password set all 6 positions For space press ENT without choosing a character to leave the position empty Press ESC to cancel the process The duplicator will ask for password when 11 Setup is selected 9 HDD MANAGER This command is for the management of the hard disk drive HDD installed in the duplicator Note This feature is only available on duplicators with a HDD installed If there is no HDD present in the duplicator this feature will NOT show in the menu of commands 9 1 Select Image Allows the selection of the image s present on the HDD The Scroll buttons cycle through the image s on the HDD and the ENT button confirms the selection while the ESC button cancels the selection The image s are listed in order
17. s ENT to finish Setting 7 Utility This command contains various tools to check functionality of the drive s information of the components and other system information 7 1 Information 7 1 1 Disc Info Checks the capacity and space used on the disc s inside of the drive s of the duplicator 7 1 2 Drive Info Checks the make model firmware and the channel port of the drive s that are connected to the duplicator controller Press ENT Press or to select different Drives Press ENT 7 1 3 System Info Checks the model number buffer memory and firmware version of the duplicator controller Press ENT 7 2 Erase Disc 7 2 1 Quick Erase Performs a quick erase of rewritable RW media for next use Note Do NOT perform this function on recordable R media Finish Quick Erase and eject discs Insert re writable discs and press ENT Note If the display shows O o blinking Erasing is in progress If the display shows F f blinking DVD RW Disc Formatting is in progress 10 7 2 2 Full Erase Performs a full erase and format of rewritable RW media for next use Note Do NOT perform this function with recordable R media Insert re writable disc and press ENT Finish Full Erase and eject discs Note If the display shows O o blinking Erasing is in progress If the display shows F f blinking DVD RW Disc Formatting is in progress 7
18. s menu is for the more advanced functions of the controller including changing the display of the controller updating writer drive s of specific brands setting the loop and time parameters for the burn in process to test the machine and performing firmware rollbacks to earlier versions Note The Advanced Setup is hidden within the Setup Menu step 11 To access Advanced Setup navigate to Setup Menu then press and hold down the scroll buttons simultaneously until the menu stop looping 8 9 1 Power On Time Set the amount of time the duplicator controller counts down before initializing the system The default is 15 seconds The time can be set from 5 to 99 seconds in 1 second increments 5 6 7 97 98 99 Press ENT or to select seconds and press ENT to confirm 8 9 2 Start up Menu Sets the command to be displayed first when the machine is powered up and initialized All primary commands are available to be set for Start up Copy Test Copy amp Verify Copy amp Compare etc Press ENT or to select function and press ENT to confirm 14 8 9 3 Skip Read Error Allows the duplicator to skip uncorrectable read errors on the master DVD or CD or Blu ray This feature can be turned ON or OFF 8 9 4 Change Bad Master Allows the changing of the master disc during duplication when there is an uncorrectable error on the master disc s that threatens to disrupt the copy process Press ENT or to select mode and
19. the tray s Number of drives used depends on number of copies desired It is not necessary to always use all drives 4 Use the scroll buttons to select the 4 Copy amp Compare command and press the ENT button The drives will automatically close trays and begin the copy process 5 Once the copy process is complete the tray s will open briefly and then automatically close again to begin the compare process 6 Once the compare process is completed the trays will automatically eject discs that have passed the Copy amp Compare process 8 Press ENT to load disc Analyzing source disc Start copying Copy completed and start Compare Finish and eject discs 5 Set Burn Speed This feature allows you to set the burn speed of various types of disc general CDs data and VCDs audio CDs DVDs and dual layer DVDs DVD DL Selectable burn speeds CD 1 2 4 8 10 12 16 20 24 32 36 40 default 44 48 52 56 MAX Audio CD 1 2 4 8 10 12 16 20 24 default 32 36 40 44 48 52 56 MAX DVD 1 2 2 4 4 6 8 default 12 16 18 20 MAX DVD DL 1 2 default 2 4 4 6 8 12 16 18 20 MAX To Set the Burn Speed 1 Power on the machine if not already on 2 Use the Scroll buttons to select 5 Set Burn Speed Press the ENT button 3 The first speed selection is for general CDs Use the Scroll buttons to select the desired burn speed and press the ENT button 4 The second speed sel
20. u ray is not recognized in the writer drive s a Test the blank disc in another writer drive A faulty writer drive will not recognize blank discs b Change the blank disc to another disc A defective blank disc will not be recognized by the writer drive c Change the brand of media or media type Certain types of media may not be compatible with the drives Poor quality media can also cause high failure rate 19 Copyright 2010 All rights reserved 20
21. y menu commands and real time status our CD DVD Blu ray Duplicator Controller provides a fast and reliable solution for CD DVD and Blu ray duplication up to 11 targets from one single master disc Operating Environment Temperature Working Temperature 0 C 75 C Storage Temperature 20 C 85 C Humidity Working Humidity 20 80 Storage Humidity 5 95 LCD Front Panel Overview Control Buttons There are 4 control buttons ENT ESC Scroll Button DOWN ESC Button ESCAPE LCD Screen Scroll Button UP ENT Button ENTER Up Backward To navigate backward in the menu Down Forward To navigate forward in the menu ENT Enter OK Execute the function ESC Escape Cancel Go back to the previous level in the menu 2 Menu Overview 2 TEST Simulates the copy process but no data is recorded onto the blank disc s Note Test mode can only be done with DVD R and CD R media only 3 COMPARE Performs a bit for bit comparison between the master disc and copied disc s 3 Below is a quick reference chart of the functions available on all of our CD DVD Blu ray Duplicator Controllers After the drives are successfully installed user may access the menu functions by powering on the system 1 COPY Copies the master CD DVD Blu ray All contents of the master disc will be duplicated on to all target disc s simultaneously 4 COPY amp COMPARE Copies the master CD DVD Blu ray and then i
Download Pdf Manuals
Related Search