Texecom Premier 412 816 832 User Guide
Contents
1. BEST MANUFACTURER 2000 amp 1999 THANK YOU FOR VOTING TEXECOM USER GUIDE Z Premier 412 7 Premier SIG Y Premier 32 Security Control Panels Ce Texecom www texe com Premier 412 816 832 User Guide Operating Your Alarm System This document covers the everyday operation of your alarm system for details on more advanced operation and system programming please refer to the Premier 412 816 832 Master User Manual Away Arming the System Enter your Access code DDD followed by the Gm Ge key The Armed light will flash and the exit sounder will sound for the duration of the exit time Stay Arming the System Enter your Access code COCOCOCO followed by the key The system will normally arm immediately the Armed light will flash slowly indicating that the system is Stay armed Disarming During Entry Enter the premises via the designated entry point The entry tone will sound proceed directly to the remote keypad and enter your Access code DOOD Disarming When Not in Entry Proceed directly to the remote keypad and enter your Access code DDD followed by the sP Wo key Note If your system consists of only one partition you will not have to press the 6z2 No key Bypassing Zones Enter your Access code DDOD followed by the key Enter the zone or zones to be bypassed e g 02 04 etc When all required zones have been selected press Gm es to Away arm the system with the selected zones bypassed2. arm immediately the Armed light will flash slowly indicating that the system is Stay armed Bypassing Zones Press the key Enter the zone or zones to be bypassed e g 02 04 etc When all required zones have been selected press Gm gt C es to Away arm the system with the selected zones bypassed to Stay arm the system with the selected zones bypassed to return to the normal disarmed state with the selected zones bypassed INS195 2 3 Service Faults Displayed on LED Keypads Fault Condition AC Fail Telephone Line Fault 2 Wire Smoke Alarm Box Tamper amp Auxiliary Input Press CA to view type lights 1 5 indicate Light 1 Box Tamper Light 2 Auxiliary Tamper Light 3 Auxiliary PA Light 4 Auxiliary Tamper UK Bell Module Light 5 Bell Tamper UK Bell Module Date or Time Lost Zone Tamper Trouble Press to view zone number Keypad Tamper Removed Press CO to view keypad number Equipment Faults Press to view fault type Light 1 Output 1 Fault Light 2 Output 2 Fault Light 3 Siren Bell Fault Light 4 2 Wire Smoke Sensor Fault Light 5 Auxiliary Fuse Failed Light 6 Battery Fault Light 7 Service Timer Zone Soak Test Failed Light 8 Communication Fault Texecom www texe com Texecom Ltd 2000 2003 INS195 2
3. to Stay arm the system with the selected zones bypassed to return to the normal disarmed state with the selected zones bypassed Reset Alarms Faults Enter your Access code DDOD then enter GOP or press Ges Last Alarm Log Enter your Access code DODA and then enter GC The remote keypad will display the zones that caused an alarm when the system was last armed Press to return to the normal disarmed state 2 INS195 2 Premier 412 816 832 User Guide Acknowledging a New Service Fault Should the Service light start flashing enter your Access code DDD and then enter eC2 gt The remote keypad will display all Service Faults see Service Faults Table on back page Press or to acknowledge the fault and return to the normal disarmed state Toggle Chime On and Off Enter your Access code DODA and then enter P or Em Change User Access Code Enter your existing Access code DODA and then enter gt Enter your new Access code DODA followed by the C Q key Now re enter your new Access code DODD for confirmation Abort Communications Enter your Access code DDOD and then enter e Operating Your Alarm System with Quick Commands If your Installer has programmed the Quick Commands the following procedures can be used Away Arming the System Press the Gelies key The Armed light will flash and the exit sounder will sound for the duration of the exit time Stay Arming the System Press the key The system will normally
Download Pdf Manuals
Related Search