Home

SCANDLIGHT

1. 20 C 40 C 5 IP degree IP20 III Technology Parameter 1 Voltage ACI00V 240V 60 50HZ 2 Power 20W 3 Outline size 500X 350X 180mm Packing size 590410 245mm 4 N W 5 3Kg G W 5 8Kg 5 LED Lamp 244LED Red Green Blue White four color LED 1 LED o5 2 LED angle 24 1 3 LED current 500mA IV Installation 1 Install replace LED lamp Unscrewed the 6pcs Unscrew screw on the 4pcs the fixed helmet screw on the light board First unscrewed the three screws of the helmet then removed to helmets if a part of LED damaged you need to use the thermostat electric iron be removed Installation method is just the opposite Warning 1 The light power supply must be disconnected when replacement of the LED does not bright 2 you can repair the light before you must use a thermostat with anti static electric iron and wear anti static rings 2 Power supply wire Connection Using a dedicated plug to connect the 4eye LED light and power 4eye LED light should pay attention to whether the voltage and frequency between signs and on the power supply are the same or not Suggested that each light has a separate power supply switch this can be turned on or off at random for each 4eye LED light The 4eye LED light selection of input voltage and frequency parameters as follows Voltag AC100V 240V Frequency 60 50Hz If the power cable is damaged please contact the area agents or a
2. The light was designed by electric shock protection type and must connect to the power supply system which well earthed Furthermore the ground wire of the light must connect to the ground wire of the power supply system ground wire interface of the light must well connect with the light body or light must well earthed 9 Please check if the voltage is accordance with the rated power before installing 10 Please never use the power cable which was damaged the insulation cover meanwhile never put the power cable on any other wire Please pull out the power cable by handle the plug when light is stop working or cleaning never pull out it roughly or handle the wire directly 11 The light with safety cable hole please take the attached safety cable go through the hole as a supporting hanging basic on safety consideration 12 The light doesn t include any spare parts for repair please check if all the parts are well installed and screws are drove tightly before operating It s prohibited to use the light when the cover is opened Notice Please make sure it s power off before any installation repair and clean Il Introduction 1 Features 1 auto move mode 2 sound controller mode 3 master slave mode 2 Technical Features 1 Control channel 6 DMX channels 2 Operating modes standard DMX512 controller control mode 3 Appearance metal shell streamlined designs 4 Working environment indoor
3. Bracket 2 Signal Cable 1PCS b Clamp 3 User s Manual 1PCS d Safety Cable 4 Maintenance Card 1PCS N Unpacking Instruction Please check if all the contents are completed after unpacking then check if the light is undamaged Please you can keep the original package and return to the factory if it s damaged 3 AC Power Check if the voltage is accordance with the rated power 2 4 Safety Specifications All the safety items of operation includes installation and before operating 1 Unpacking the light case and take out all the accessories and open the poly package take out the light from the flight case and put it in a certain platform for operation 2 This device for indoor use only the protection grade is IP20 the light must keep dry and avoid to use under the Moist Overheat or Dusty surroundings And keep the light far away from the water or other liquid 3 Installing of the light must keep a distance with any flammable objects by 1M at least 4 Please never install the light on the surface of the flammable objects 5 The installation operation and maintenance must be managed by the qualified professional and make sure to operate it under the instruction of the Manual 6 Make sure the work environment temperature of the light maximum 40 C and minimum 20 C 7 The temperature of the light surface will up to 85 C even under the normal cooling so never touch it by hand 8
4. Total control Channel All 161 170 Gobo model l function 171 180 Gobo mode 2 181 190 Gobo mode 3 191 200 Gobo mode 4 201 255 Gobo mode 5 Sound control 0 9 Off 10 69 Auto model individual 70 129 Auto mode 2 control 1 130 194 Auto mode 3 195 255 Static Display Channel 9 0 9 Off 10 69 Auto model Total 70 129 Auto mode2 control mode 130 194 Auto mode3 195 255 Static Display Gobo 0 255 Set gobo by self control 0 9 Off individual 10 69 Auto model control 2 70 129 Auto mode2 130 194 Auto mode3 Channel 195 255 Static Display 3 Overall 0 255 fast slow control speed adjustment Gobo 0 255 fast slow controls peed adjustment 0 9 Off aia 4 10 69 Auto mode 1 Channel 4 70 129 Auto mode2 control 3 130 194 Auto mode 3 195 255 Static Display 0 9 Off Channel individual 10 69 Auto model 5 control 4 70 129 Auto mode2 130 194 Auto mode3 195 255 Static Display Channel 6 dimmer 0 255 Brightness dark VI Maintenance 1 Clean and use frequency To confirm the power supply have cut off before disconnect the light or repair it it is very important to keep the light cleaning not only can keep the light maximum brightness output but also can prolong their use life please use the high quality professional glass and soft cloth to clear up the equipment not permission to use the alcohol and organic liquid clean at least once each year use vacuum dust collector When the light does not start check whether the light power
5. connect to the DMX input of second slave light from the DMX output of the first master light analogously till connected all the slave lights and insert the last connector to the output of the final light If you want to prolong the connection of signal cable the connection of the pins between male connector and female connector should be 1 to 1 2 to 2 3 to 3 or it will cause communication interruption Notice the diameter of core of every cable should be 0 5mm at least double core shelter cable should be used The signal connecting must use the attached 3 pins XLR cable Notice all the internal lead wire of the 3 pins XLR cable should not touch to each other or connect to the connector The light is available to receive the DMX512 signal connect the signal plug to the panel which marked with IN and connect it to the next light then connect to the IN of next light from the OUT The DMX signal terminal organ is recommended when the lighting signal is connecting It will avoid to damage the signal which caused by the noise DMX terminal organ is a XLR connector connect with a 120Q resistor between the pin 2 and pin 3 of the XLR connector and connect it to the last OUTPUT socket of the final light 2 DMX channel list DMX Functio DMX value Features channel n 0 100 Individual control speed adjustment 101 150 fast slow 120R 1W 151 160
6. modes SP speed d off Show 3 Press the MODE key to display the DMX512 address code and then press UP and DOWN keys to adjust address code 4 Press FUNC key to enter the feature setup and then press UP and DOWN keys to enter the function parameters for setting options 2 Function Code Control Operation 1 On display A001 2 Press MODE key to display G 3 in the G 3 state can press UP and DOWN keys increment or decrement G 3 sound control mode G 2 auto running model G 1 Strobe Mode S the state of S can press UP and DOWN keys increment or decrement Select a sub machine address 3 DMX Address Code Setting HEE Se COA MODE FUNC UP DOWN Every light should be set with DMX address code when you are using the controller to control multi lights itis used to receive the signal from the controller The present address code of the light address code of last light channel quantity of the light 4eye LED light with 6 Channels so it should be under the 16channle control mode the DMX address code of the first light is 001 the second should be 017 the third should be 049 analogously VI Appendix 1 Usage of the Signal Cable Connector The connection between the output of master light and input of the salve light it s available to use the 3 pins XLR cable which provided by the manufacturer Signal cable from the DMX output of the controller to the input of the first master light and
7. out the maintenance service card after finish repair and transferred the finished products to warehouse 6 The warehouse personnel should be talk with customer service timely to confirm the shipping issues There are customer service personnel need to confirm the repair costs and send to the finance department 3 Complain 1 The salesman will check the details of complained problem included the item no delivered quantity delivery time faulty and pictures and the requirement of customer 2 QC and Technology department will analysis the complained problem and give a final solution to customer Vil Faulty Disposal Familiar Faulty Disposal Light can not start 1 Check if the fuse burnt out or not Check if the power connect well or not 3 Check if the circuit board 12V or 5V short circuit of earth Light can be shine well but 1 Check if the light s DMX original address setup can not be control by right or not controller 2 Check the connection details of communication control wire 5W white LED not brightness 1 Check if LED lamp damage or not 11
8. supply fuse blown or not if blow install the appropriate fuse and start the light after find out troubleshooting but please attention to the technically person allowed to carry out maintenance work 2 Product Return Procedure A No charge 1 First customer talking the return matters with customer service personnel 2 Until the customer returned the bad product to factory the customer service personnel need to make sure their warranty period truthfully fill out the maintenance services list 3 Both customer service and warehouse personnel to transfer responsibilities production units 4 The responsibility of production units arrange repair 5 The responsibility of production units truthfully fill out the maintenance service card after finish repair and transferred the finished products to warehouse 6 The warehouse personnel should be talk with customer service timely to confirm the shipping issues B Charges 1 First customer talking the return matters with customer service personnel 2 Until the customer returned the bad product to factory the customer service personnel need to make sure their warranty out 10 period truthfully fill out the maintenance services list 3 Both customer service and warehouse personnel to transfer responsibilities production units 4 The responsibility of production units arrange repair 5 The responsibility of production units truthfully fill
9. SCANDLIGHT DJ LED LEOPARD Item no 935789 scand ior I Preface Thank you for using our 4eye LED light For your safety 1 please read the User s Manual carefully before your operation Note This Manual includes the important information of installation operation safety instruction Please install and operate as requested in the Manual meanwhile please keep the manual for any unexpected requirement This Manual includes the important information of installation and operation Please install and operate the light according to the instructions strictly And it must be power off when open the light or before repair A Please read the complete contents of this manual please keep this manual attach with the light for any preview B In order to make sure the correct and safety installation operation and maintenance well know and follow to the instructions of Manual is necessary C We will not take any responsibility to the light damage property loss or body injure which caused by the incorrect installation operation and maintenance NOTICE the data which inside the Manual maybe changed due to the continuous improvement and we 11 not make another notice We will keep the right to any specification update during improvement Warning if the protection screen lens or UV screen got avisible damage e g scratch or chasm 1 Packing Content Caccessories Selectable l Power Cable 1PCS a
10. sk professional to replace please use the same specification cable when you replace the power cable Tip When connecting the power ground wire must yellow green color wire safety grounding electrical installation must comply with all relevant standards 3 Fixed installation of lighting including light hook and safety rope how to use Hook installation Before positioned the light ensure the stability of the installation site In the reverse hanging installation use two sets of M10 bolts with a professional big hook link the hanging screw hole on the bottom of the light must be ensure that the light will not fell down from support rack through the support rack and light hand use the safety rope for auxiliary lifting handle to ensure safety to prevent the light falling and sliding Light in the installation the bottom prohibit pedestrians Safety rope regularly checked whether there is wear and tear whether there is loose hook The manufacturer does not take any responsibility if the light falling because hanging installation is not stable Warning 1 Hook use only for light lifting 2 Hook as a handle move the light to prohibit carrying please use the handle V Operation 1 Panel Operation 1 Press MODE mode key to switch modes A001 DMX Mode G l strobe mode G 2 AUTO running mode G 3 sound control auto running model S slave machine mode 2 Press FUNC mode button to switch

SCANDLIGHT

Contents

Download Pdf Manuals

Related Search

Related Contents