Leica Steer Ready Kit Installation Manual Tractor
Contents
1. Steer Ready Kit for John Deere 8x20 23 Leica Steer Ready Kit for John Deere 8x20 6 7 Installing the Override Cable Step 1 Refer to Section 4 2 of the equipment list to ensure that you have the manual override cable Part 676176 amp termination plugs Part 676113 amp 676114 Step 2 The steering sensor into which the manual override cable is to be installed is situated behind the panel around the Steering Column Remove the screws that hold this cover 24 Step 3 Locate and unplug both the steering sensor cables Plug the override cable into one of the disconnected sockets Step 4 Plug the two terminators 676113 amp 676114 into the two plugs disconnected in Step 3 The remaining socket can remain disconnected Step 5 Route the manual override cable under the floor mat Step 6 Plug the other end of the manual override cable into the In cab harness Step 7 Replace the cover around the Steering Column Leica Steer Ready Kit for John Deere 8x20 25 Leica Steer Ready Kit for John Deere 8x20 26 6 8 Routing the Power Cable Step 1 Refer to Section 4 2 of the equipment list to ensure that you have the Power Cable Part 676177 Step 2 The vehicle s auxiliary power supply is located on the right side inside the cab on the front side of the vehicle s console Connect the Power supply cable to the In cab harness and connect it to the power supply strip It is essential that the cable is routed throughout the2. if technically possible on a parked vehicle with the engine turned off AN Danger Prepare for possible emergencies People present within the danger zone are exposed to serious bodily harm or even death People could be run over in case of malfunction of the machine The operator is obligated to stop the vehicle as soon as people enter the danger zone e Always have a fire extinguisher and First Aid kit at hand e Always have actual emergency phone numbers for Fire department ambulance and doctor handy Leica Steer Ready Kit for John Deere 8x20 33 Leica Steer Ready Kit for John Deere 8x20 34 Purchase Returns Leica Geosystems offers customers the ability to return any agricultural products purchased within Australia under our exclusive 8n8 Satisfaction Guarantee Program You will receive a full refund of your purchase price if you meet the following criteria The equipment must be returned and received in the Leica Geosystems Brisbane Qld office within 8 days of the invoice date The equipment must have no more than 8 hours of auto steer operating time on the system meter The equipment must be in as new condition and in original packaging If you are not satisfied for any reason you may return your new Leica mojoRTK products no questions asked This is the Leica 8n8 Satisfaction Guarantee Warranty Leica Geosystems offers its Standard International Warranty which is 12 months for all agricultural product purchases and
3. of the machine and the surrounding area He should shut down or assume manual steering control in dangerous situations To shut down the Leica Steer Ready Kit turn off the power switch so that the light is off 4 Equipment List 4 1 SRK Part A 676035 Apt Description Part dl Universal Bracket 676173 M6 x 60mm Bolt M6 Star Washer Qty Description Part 1l Steer Ready Controller 676171 gt Qty Description Part 1 CAN Extension Cable 676030 Leica Steer Ready Kit for John Deere 8x20 Leica Steer Ready Kit for John Deere 8x20 g IS Qty Description Part am __ moo SRKISO C able 57659 Engage Switch 676191 Qty Description Part Qty Description Part 1 Wiring Harness SR Controller 676172 1 In Cab Wiring Harness 676186 SRK Part B 676036 676177 John Deere Power Cable 676177 4 2 CATA i 676183 676183 Flow Sensor Cable 676183 A 676176 676176 T Manual Override Cable 676176 676180 676180 E Description 1 Hydraulic Valve Cable 676180 Qty Description Part l Steering Wheel Encoder Terminator A 676113 Qty Description Part Steering Wheel Encoder Terminator B 676114 Leica Steer Ready Kit for John Deere 8x20 Leica Ste
4. special attention that no children are near or on the vehicle which is fitted with a Leica Steer Ready Kit especially when the Leica Steer Ready Kit is active Children are unpredictable and supervision is limited when operating the Leica Steer Ready Kit They might be exposed to additional danger Before starting field work make yourself comfortable with the use of the Leica Steer Ready Kit and the vehicle As soon as the Leica Steer Ready Kit is activated an adult responsible person has to be in charge of supervision and monitoring In dangerous situations it is always safer to disengage the Leica Steer Ready Kit and drive by hand in order to avoid personal injury or material damage At no time should there be any person within the danger zone after the Leica Steer Ready Kit is activated At any sign of danger the operator should deactivate the Leica Steer Ready Kit immediately He has to ask any person within the danger zone to leave promptly Only when there are no more people within the danger zone can he re activate the Leica Steer Ready Kit For service and control duties only authorized persons can enter the danger zone after verbal confirmation with the operator Such people have to be clearly informed about possible dangers before entering the danger zone All activities between the operator and these persons should be discussed before hand All service adjustment and control duties on this Leica Steer Ready Kit should only take place
5. with local regulations relating to safety and accident prevention e To inform Leica Geosystems immediately if the product and the application becomes unsafe The person responsible for the product must ensure that it is used in accordance with the instructions This person is also accountable for the training and the deployment of personnel who use the product and for the safety of the equipment in use Unauthorized modification of machines by mounting the product may alter the function and safety of the machine Precautions Follow the instructions of the machine manufacturer If no appropriate instruction is available ask machine manufacturer for instructions before mounting the product Hazards of Use Only Leica Geosystems authorized service workshops are entitled to repair these products Beware of inadequate steering if machine is defective like after a crash or other damaging events or alterations to the machine Precautions Periodically perform control measurements and field adjustments on the machine as specified in the User Manual While steering or navigating the machine accidents may occur due to a the operator not paying attention to the Surroundings persons ditches traffic etc or b malfunctions of a system component interference etc Precautions The operator assures that the machine is operated guided and monitored by a qualified user e g driver The user has to be able to take emergency measures fo
6. 90 days for battery products Please go to the website to review the warranty document Leica Steer Ready Kit for John Deere 8x20 35 Original text Printed in Singapore O 2009 Leica Geosystems Pty Ltd Brisbane Australia 676193 Version 1 2 0en Leica Geosystems Pty Ltd 270 Gladstone Road Dutton Park QLD 4102 dl eed ELE Phone 61 7 3891 9772 when it has to be right www mojoRTK com Geosystems
7. Version 1 2 0 English Leica Steer Ready Kit Installation Manual Tractor Model John Deere 8x20 AutoTrac Ready O when it has to be right Leica Geosystems Introduction Purchase Product Identification Leica Steer Ready Kit for John Deere 8x20 2 Congratulations on your purchase of a new Leica Steer Ready Kit This manual contains important safety directions as well as instructions for installing the product and operating it Refer to the Safety Directions for further information Read carefully through the Installation Manual before you begin operation of machinery The Leica Steer Ready Kit is to be used solely in combination with Leica mojoRTK system Therefore it s mandatory to also observe the directions and instructions contained in the Leica mojoRTK User Manual To ensure safety when using the system please also observe the directions and instructions contained in the User Manual and Safety Handbook issued by the e Agricultural machinery manufacturer This manual describes how to install the Leica Steer Ready Kit Even if you have installed other Leica Geosystems products before we recommend you read this manual to ensure correct installation of this product The model and serial number of the Leica Steer Ready Kit are indicated on the packaging Please enter them here and always refer to this information when you need to contact your agency or Leica Geosystems authorized service workshop Make Mode
8. ation of agricultural machine by mounting or installing the product may alter the function and safety of the machine Precautions Follow the instructions of the machine manufacturer If no appropriate instruction is available ask machine manufacturer for instructions before mounting or installing the product Limits of Use Suitable for use in an atmosphere appropriate for permanent human habitation not suitable for use in aggressive or explosive environments Local safety authorities and safety experts must be contacted before working in hazardous areas or in close proximity to electrical installations or similar situations by the person in charge of the product Responsibilities Leica Geosystems AG CH 9435 Heerbrugg hereinafter referred to as Leica Geosystems is responsible for supplying the product including the user manual and original accessories in a completely safe condition The manufacturers of non Leica Geosystems accessories for the product are responsible for developing implementing and communicating safety concepts for their products and are also responsible for the effectiveness of those safety concepts in combination with the Leica Geosystems product Leica Steer Ready Kit for John Deere 8x20 29 Person in charge of the product Leica Steer Ready Kit for John Deere 8x20 30 e The person in charge of the product has the following duties e To understand the safety instructions of the product e To be familiar
9. ed results rests as always with the driver As common with most all machinery the basic rule applies The more exact the system is adjusted calibrated and operated the higher the quality of results will be Leica Steer Ready Kit for John Deere 8x20 5 GE 3 General AN Caution Leica Steer Ready Kit for John Deere 8x20 6 Pre Installation Vehicle Preparation 1 Park the vehicle on a hard level surface and block the front and rear wheels 2 Align the steering wheels straight ahead 3 Remove all dirt and trash from the areas of the vehicle where the Leica Steer Ready Kit will be installed 4 Lower the 3 point hitch to its lowest point Consult the Tractor s Operator s Manual for assistance Note The left and right hand sides of the vehicle are referenced while standing behind the vehicle facing the normal direction of travel System Description The Leica Steer Ready Kit is capable of interfacing to existing actuators and sensors to steer vehicles like tractors and other self propelled machines in agriculture and forestry applications The Leica Steer Ready Kit is composed of the Steer Ready Controller and associated cabling The Leica Steer Ready Kit is designed to interface to the Leica mojoRTK system via CAN bus The Leica Steer Ready Kit is designed to assist the machine operator to use the equipment more efficiently Even when relying on the function of the Leica Steer Ready Kit the driver is still responsible for observation
10. ed under the cab in Step 4 Ensure that it is suitably positioned and secured with cable ties Step 6 Route the cable into the cab of the vehicle ensuring that it is suitably positioned and secured with cable ties Step 7 Remove the screws that hold the right plastic cover Lift out the perforated plastic lining as well screws Step 8 Route the cable behind the seat so that it will be behind the perforated lining removed previously ensuring that it is suitably positioned Insure that all connectors are easily accessible for further installation It is essential that the cable is routed throughout the vehicle in a position that is away from excessive vibration amp heat sources such as exhaust manifolds and or radiators amp that there is enough length in the cable to prevent stretching or excessive tension whilst the vehicle is in normal operation ensuring that it can be mounted securely Leica Steer Ready Kit for John Deere 8x20 21 Leica Steer Ready Kit for John Deere 8x20 6 5 Routing the CAN cable Step 1 Refer to Section 4 1 of the equipment list to ensure that you have the correct Wiring Harness Part 676591 and 676030 Step 2 Locate the mounting position of the associated Leica mojoRTK console which will typically be the vehicle s factory fitted radio DIN slot If the Leica mojoRTK is not yet fitted route the ISO C cable to where it is expected to be Step 3 Remove the Leica mojoRTK console from t
11. er Ready Kit for John Deere 8x20 Flow Sensor Terminator 676115 10 5 Controller Installation Before commencing the Installation lower the 3 point linkage of the tractor to Its lowest point and turn the front wheels of the tractor so that they are positioned straight ahead Consult the Tractor s Operator s Manual for assistance DO NOT START tag is attached to the ignition AN Da nger Before beginning this section of the installation please ensure that the vehicle is turned off and a The following will give a general outline of the steps necessary to install the SRK Controller assembly Sad SR Controller Bracket Mounting Step 1 Working from the RHS of the vehicle locate the correct mounting position The SR Controller Bracket slotted bolt hole will align with the existing bolt hole for the wiring harness bracket for ease of installation Leica Steer Ready Kit for John Deere 8x20 11 Leica Steer Ready Kit for John Deere 8x20 12 Step 2 Once located remove the existing bolt and mount the SR Controller Bracket to the vehicle Tighten the mounting bolt Step 3 Mount the Steer Ready Controller to the Bracket using the bolts and washers as supplied 6 Routing the Wiring 6 1 Connecting to the SR Controller O DANGER Da nger Before beginning this section of the installation please ensure that the vehicle is turned off and a DO NOT START tag is attached to the ignition Step 1 Refer to Secti
12. he DIN slot using the tools supplied in the Leica mojoRTK console kit and plug the Leica mojoRTK ISO C cable Part 675591 into the ISO C plug in the rear of the unit Step 4 Connect the other end of the ISO C cable to the In Cab harness already fitted If required use the CAN Extension Cable Part 676030 It is essential that the cable is routed throughout the vehicle in a position that is away CS from excessive vibration amp heat sources such as exhaust manifolds and or radiators amp that there is enough length in the cable to prevent stretching or excessive tension whilst the vehicle is in normal operation ensuring that it can be mounted securely 22 6 6 Installing the Engage Switch Step 1 Refer to Section 4 1 of the equipment list to ensure that you have the engage switch Part 676191 Step 2 The engage switch is to be installed in the console on the right armrest There should be a spare rye ONES place for a switch with a blank insert in the hole The blank can be removed by lifting it with a small flat L i BY A blade screw driver D TE en Step 3 Feed the in cab cable for the engage switch up from under the armrest Step 4 Connect the switch to the cable crimps as indicated in Numbers are labeled on the crimps as well as the switch to assist in this step ack Step 5 Press the switch into the console so that the side that locks down when pressed towards the back of the machine Leica
13. irections and adhere to them Intended Use e The Leica Steer Ready Kit is exclusively developed for usage in agriculture or forestry by persons in control e The Leica Steer Ready Kit is only intended to be fitted to agricultural tractors It is not permitted to install this product in any other vehicles e Use of the product without instruction e Use outside of the intended limits e Disabling safety systems e Removal of hazard notices e Opening the product using tools for example screwdriver unless this is specifically permitted for certain functions e Modification or conversion of the product e Use after misappropriation e Use of products with obviously recognizable damages or defects e Use with accessories from other manufacturers without the prior explicit approval of Leica Geosystems e Inadequate safeguards at the work site for example when using on the intended site e The Leica Steer Ready Kit is not suitable for applications on narrow dikes or on steep hillsides where danger of vehicle roll over exists 8 3 Environment AN Danger 8 4 Manufacturer of the product Manufacturers of non Leica Geosystems accessories Adverse use can lead to injury malfunction and damage It is the task of the person responsible for the equipment to inform the user about hazards and how to counteract them The product is not to be operated until the user has been instructed on how to work with it Unauthorized modific
14. ispose of the product appropriately in accordance with the national regulations in force in your country Always prevent access to the product by unauthorized personnel Product specific treatment and waste management information can be downloaded from the Leica Geosystems home page at http www leica geosystems com treatment or received from your Leica Geosystems dealer On public roads and drives always disengage the Leica Steer Ready Kit via the power switch For safety reasons it is better if you keep one hand on the steering wheel when using the Leica Steer Ready Kit at speeds over 6 mph 10 km h In case of malfunction you are able to take action immediately Leica Steer Ready Kit for John Deere 8x20 31 el Zone 50 50 lt m on 20 m gt m Leica Steer Ready Kit for John Deere 8x20 32 With exemption of the driver no other person should ride in the drivers area of the vehicle fitted with a Leica Steer Ready Kit Additional persons could distract or block visibility of the driver from operating and observing the Leica Steer Ready Kit which could lead to dangerous situations The presence of a rider on a passenger seat is only acceptable for brief observations or for training purpose The passenger seat is never considered a children seat Only persons especially experienced with the operation of the machine should be considered for schooling on a machine which is fitted with a Leica Steer Ready Kit Pay
15. l Serial No _ Symbols Symbols used in this manual have the following meanings Indicates an imminently hazardous situation which if not avoided will result in death or Da n ger serious injury Indicates a potentially hazardous situation or an unintended use which if not avoided Wa MIND could result in death or serious injury J Indicates a potentially hazardous situation or an unintended use which if not avoided Ca ution may result in minor or moderate injury and or appreciable material financial and environmental damage Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner Note The absence of specific alerts does not mean that there are no safety risks involved Leica Steer Ready Kit for John Deere 8x20 3 Table of Contents Leica Steer Ready Kit for John Deere 8x20 4 Product OVER rara aid o Soo 5 1 2 Pre Installation Vehicle Preparatoria eles 6 3 SVStem DESC O rt EA E 6 oa E E EE EG asm EE DE RE Ge IE Ee EE Ee 7 TL SEE PAAS IOD DE NG a a ee GE Se GE Ge ne ee ee eee ene eee ene 7 42 SRK PART B OZO O O ED IE dico ED eee ee 9 5 Controller InstallatiOi oe ER SEE GO eee EE RE OE GE EE EE EE EE ee ce eters cine OE ER EE EE EE EO GE IE GE 11 5 1 SR CONTROLLER BRACKET MOUNTING 2 tee Se ES ee De EE Du Ee coria rocio ici 11 O POURING TS VINNIE EN OE EE OE EE EE EE N 13 6 1 CONNECTING TO THE SR CONTROLLER us soes a
16. on 4 1 of the equipment list to ensure that you have the correct Wiring Harness Part 676172 Step 2 Locate the Steer Ready Controller that was mounted to the vehicle in Section 5 of this manual Step 3 Connect the black Deutsch connector of the Wiring Harness to the black rimmed socket of the Steer Ready Controller Leica Steer Ready Kit for John Deere 8x20 13 Leica Steer Ready Kit for John Deere 8x20 Step 4 Connect the grey Deutsch connector of the Wiring Harness to the grey rimmed socket of the Steer Ready Controller Step 5 Leave the other end of the SR Controller wiring freely available as each of these available connectors will be used for the various components of the Leica Steer Ready Kit It is essential that the cable is routed throughout the vehicle in a position that is away from excessive vibration amp heat sources such as exhaust manifolds and or radiators amp that there is enough length in the cable to prevent stretching or excessive tension whilst the vehicle is in normal operation ensuring that it can be mounted securely 6 2 Routing the Flow Sensor Cable Step 1 Refer to Section 4 2 of the equipment list to ensure that you have the correct Wiring Harness Part 676183 and terminator 676115 Step 2 Working from the LHS of the vehicle locate the onboard Flow Sensor of the Vehicle as shown Step 3 Once located remove the existing plug and connect the 6 pin AMP type connector to the unde
17. r all John Deere 8x20 Autotrac Ready Machines Certain vehicle variations and non standard modifications may affect some cable lengths Extension cables may be required see your local Leica Dealer This installation manual will provide the necessary steps to successfully install the Leica Steer Ready Kit To ease the use of this manual please observe the following advice Relating to all pictures and schematics they are to be seen as reference only There may be slight deviations from the actual looks of the Leica Steer Ready Kit These deviations are caused by individual applications and have no impact on the function capabilities of the Leica Steer Ready Kit Leica Geosystems original spare parts are especially designed for the Leica Steer Ready Kit They live up to the high design standards for safety and reliability We advise you that components or parts not provided by Leica Geosystems for the Leica Steer Ready Kit should not be used because they might jeopardize the safety and function of the Leica Steer Ready Kit We therefore can not be responsible for such redesign or adaptations Any obstinate changes on our Leica Steer Ready Kit void the company warranty In addition conformity dedlaration or local authority regulations could be voided This also applies to the removal of factory applied seals The Leica Steer Ready Kit supports you and improves your efficiency while working in the field The responsibility for quality and work relat
18. r example an emergency stop The absence of instruction or the inadequate imparting of instruction can lead to incorrect or adverse use and can give rise to accidents with far reaching human material financial and environmental consequences Precautions All users must follow the safety directions given by the manufacturer and the directions of the person responsible for the product During dynamic applications there is a danger of accidents occurring if the user does not pay attention to the environmental conditions around for example obstacles excavations or traffic Precautions The person responsible for the product must make all users fully aware of the existing dangers Inadequate securing of the work site can lead to dangerous situations for example in traffic on building sites and at industrial installations Precautions Always ensure that the work site is adequately secured Adhere to the regulations governing safety and accident prevention and road traffic If the product is improperly disposed of the following can happen If polymer parts are burnt poisonous gas are produced which may impair health By disposing of the product irresponsibly you may enable unauthorized persons to use it in contravention of the regulations exposing themselves and third parties to the risk of severe injury and rendering the environment liable to contamination Precautions The product must not be disposed with household waste D
19. ring Control Valve of the vehicle Step 4 Working from the Hydraulic Steering Control Valve route the cable towards the SR Controller ensuring that it is suitably positioned and secured with the cable ties Connect to the SR Controller Harness that was fitted in Section 6 1 It is essential that the cable is routed throughout the vehicle in a position that is away from excessive vibration amp heat sources such as exhaust manifolds and or radiators amp that there is enough length in the cable to prevent stretching or excessive tension whilst the vehicle is in normal operation ensuring that it can be mounted securely 6 4 Routing the In Cab Harness Step 1 Refer to Section 4 1 of the equipment list to ensure that you have the correct Wiring Harness Part 676186 Step 2 Remove the back cover on the cab by loosening the bolts in each corner of this cover The holes are slotted lift to remove Leica Steer Ready Kit for John Deere 8x20 19 Leica Steer Ready Kit for John Deere 8x20 20 Step 3 Locate the entry point into the vehicle s cab at the rear right side of the cab This will provide entry into the cab space near the implement controls Step 4 Feed the end of the long cable of this harness under the cab from back to front of the vehicle cab choose the route carefully Step 5 Locate the Steer Ready Controller Harness that was fitted in Section 6 1 and connect to the cable of the In cab harness that was f
20. rside of the Flow Sensor of the vehicle Leica Steer Ready Kit for John Deere 8x20 15 Leica Steer Ready Kit for John Deere 8x20 16 Step 4 Plug the flow sensor terminator 676115 into the cable that was originally connected to the flow sensor Step 5 Working from the Flow Sensor route the cables to the SR Controller ensuring that it is suitably positioned and secured with the cable ties and connect to the SR Controller Harness that was fitted in Section 6 1 It is essential that the cable is routed throughout the vehicle in a position that is away from excessive vibration amp heat sources such as exhaust manifolds and or radiators amp that there is enough length in the cable to prevent stretching or excessive tension whilst the vehicle is in normal operation ensuring that it can be mounted securely 6 3 Routing the Steering Solenoid Cable Step 1 Refer to Section 4 2 of the equipment list to ensure that you have the correct Wiring Harness Part 676180 Step 2 Working from the LHS of the vehicle remove the battery cover and the panel Locate the onboard Hydraulic Steering Control Valve of the Vehicle k Sy gt ie A E N ME WE y 4 YE MAL S N 2b A y he TN ME 1 AG YY ji iel DY Leica Steer Ready Kit for John Deere 8x20 17 Leica Steer Ready Kit for John Deere 8x20 18 Step 3 Once located remove the existing plug and connect the 4 pin connector to the onboard Hydraulic Stee
21. sk ee Se EE RS ee ee ic ae Ee 13 6 2 ROUTING THE FLOW SENSOR GABE ao aida 14 6 35 ROUTING THE STEERING SOLENOID CABLE se Dee ee Ge DA GEE DE Ge acidss 17 6 4 ROUTING THE IN CAB HARNESS ees vex Ge Ge oe ici 19 6 5 ROUTING TAE CAR A ol Se EG 22 6 6 INSTALLING THE ENGAGE SWITCH soe Gee EED GE ED EG n GOS OE EE EE GE RA EE DS ER REG De DO EE 23 6 7 INSTALLING THE OVERRIDE CAB Re adi s Dee cada 24 Gs ROUTE TIE PM EABIE ol odas 26 7 Wiring Harness Dia raise A ge GR Ge GE es 27 B Sale A se An E REO N RE IE N EE EE Se ee Do 28 A 28 8 2 INTENDED USE ee ee ee Ge ee ee ee ee ee ee Ge ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee Ge ee ee ee ee ee ee ee ee 28 gt ar OE tdi 29 9 4 RESPONSIBILITIES nee RE EO ee EE GEE DE EED DE Ee EO ER EE GE GE DE ee ED EG EE EE Ee Ee GE EE 29 e OAAR DS k GELEE ee oe o ER ee 30 1 Benefits To understand the user manual Use only original parts GE Product Overview The Leica Steer Ready Kit is the first step in getting your equipment Leica mojoRTK ready It consists of a Steer Ready Controller amp associated Wiring Harness brackets and bolts which will form the foundation of your new auto steer solution The Leica Steer Ready Kit is designed to be used in conjunction with the Leica mojoRTK console The installation of a Leica mojoRTK console is not included in this manual Please refer to your local dealer or the relevant manual for further details on this product The Leica Steer Ready Kit is suitable fo
22. vehicle in a position that is away from excessive vibration amp heat sources such as exhaust manifolds and or radiators amp that there is enough length in the cable to prevent stretching or excessive tension whilst the vehicle is in normal operation ensuring that it can be mounted securely Wiring Harness Diagram 676172 LG 676180 Fi To Flow Ma Sensor CO N lt e L PE Brenes To Valve Steer Ready Controller Exterior to Cab mojoRTK Console Interior to Cab S To L STATES Override Sensor To John 676030 5 AE 676177 qe Deere N Power CO ITA Leica Steer Ready Kit for John Deere 8x20 27 Description 8 2 Permitted Use Adverse Use Leica Steer Ready Kit for John Deere 8x20 28 Safety Directions General The Leica Steer Ready Kit is to be used solely in combination with Leica mojoRTK system Therefore it s mandatory to also observe the directions and instructions contained in the Leica mojoRTK User Manual The following directions should enable the person responsible for the product and the person who actually uses the equipment to anticipate and avoid operational hazards The person responsible for the product must ensure that all users understand these d
Download Pdf Manuals
Related Search