IN915GVE 2.0
Contents
1. INSISGVE 2 0 WARNING Misplaced J D Intel Pentium 4 with 90nm 6 5nm Process Socket 11 5 Processors Incorrect jumpers and connectors settings may lead to damage to your motherboard and will void your motherboard Su ppo rt warranty Please pay special attention not to connect these headers in wrong direction DO NOT change ANY jumpers while the motherboard has power User s Quick Start Card Version 2 00 http www bcmcom com Jumper Connector Header Inspect the Package One IN915GVE Motherboard Jumper Description One IDE Cable 80 Pins ICMOS Clear CMOS One Floppy Cable One SATA Cable and One Power Cord JUSB USB S3 Wake up Jumper sis One Driver CD One User s Quick Start Card N er One Standard I O Shield s Connector Description Note DRIER Header Responsibility ala AUX In AUX In This manual is provided As ls with no warranties of any kind expressed or implied including but not limited to the CD In CD In implied warranties or conditions of this product s fitness for any particular purpose In no event shall we be liable for any CFPA Front Audio loss of profits loss of business loss of data interruption of business or indirect special incidental or consequential PCL PCI Slot 3 damages of any kind even the possibility of such damages arising from any defect or error in this manual or product We 2 reserve the right to modify and update the user manual without prior notice PCI2 PCI Slot 2 A p PCI12. PCI Slot 1 Attention CPU Socket Protector PCI EXP1 PCI Express x16 Please read the user s manual carefully prior installing the Processor Do not remove CPU socket protector if no CPU is J17 Front USB Header 2 in the LGA775 socket Place the CPU protector back to the socket during transport and when returning board for TIS Front USB Header 1 service http www intel com cd channel reseller asmo ICEULEAN CPU Fan Header na eng products box processors desktop proc dsk p4 technical reference 99345 htm processorinstallation JPWR_FAN Fan 2 Header JSYS_FAN Fan 3 Header CFP Front Panel Header A WARNING CMOS Battery Damage SATAI SATA 1 Replace your system s CMOS RAM battery only with the identical CR 2032 3V Lithium lon coin cell or equivalent battery SATA2 SATA 2 type to avoid risk of personal injury or physical damage to your equipment Improper installation might cause battery to SATA3 SATA 3 explode Always dispose of used batteries according to the manufacturer s instructions or as required by the local ordinance where applicable The damage due to not following this warning will void your motherboard s manufacturer SATA4 SATA 4 warranty IDE1 Parallel IDE FDD Floppy Additional Information PW1 ATX Power Connector 24 Pin Block Additional information on setting this board up can be found in the User s Manual in the provided CD ROM The Online PW12 ATX12V Power Connector 4 Pin Block Users Manual and FAQ Knowle
3. Signal Signal 53 B WCC vcc i 5 23 3 USB4 4 USB5 HD_LED 3 4 PWR_LED E i HD_LED 5 6 PWR_LED z lt 8 Z te 3 Case Open a qrmaaa Y intada Kromaj amnre ena f NVI SAS NIdO I5 2 N i NdD Nvdi Ud Ges WARNING Electrostatic Sensitive Device ESD Static electricity can easily damage your motherboard and will void your motherboard warranty Keep the motherboard and other system components in their anti static packaging until you are ready to install them Touch a grounded surface before you remove any system component from its protective anti static packaging Unpacking and installation should be done on a grounded anti static mat The operator should be wearing an anti static wristband grounded at the same points as the anti static mat During configuration and installation touch a grounded surface frequently to discharge any static electrical charge that may have built up in your body Avoid touching the components when handling the motherboard or a peripheral card Handle the motherboard and peripheral cards either by the edges or by the peripheral card case mounting bracket Save the Processor Socket Cover After removing the processor cover during processor installation please save the processor socket cover In the event that the desktop board needs to be returned for service or any time the processor is removed the cover should be replaced on the pro
4. cessor socket Do not Touch Socket Contact CPU Installation This processor is intended to be professionally installed Before installing the processor please review the additional notes available at http www intel com go integration Take proper electrostatics discharge ESD precautions such as using appropriate ground strips gloves and ESD mats 1 Open socket lever by pushing lever down and 2 Open load plate C DO NOT TOUCH SOCKET away from socket A Lift lever B CONTACTS D 4 Remove processor from protective cover HOLD PROCESSOR ONLY AT EDGES BEING CAREFUL NOT TO TOUCH BOTTOM OF PROCESSOR Do not discard the protective cover Always replace the socket cover if the processor is removed from the socket 3 Remove protective cover E from load plate Do not discard the protective cover Always replace the socket cover if the processor is removed from the socket 6 Close load plate Pressing down on load plate I close and 5 Hold processor with thumb and index fingers engage socket lever J oriented as shown Ensure fingers align to socket cutouts F Align notches G with socket H Lower the processor straight down without tilting or sliding the processor in the socket
5. dge Base can be found on our website by visiting our website COM1 COM Port Connector DB9 http www bcmcom com If your question is not answered in our FAQ Knowledge Base visit our forums and post your COM2 COM Port Header 10 Pin Header messages or submit a new FAQ through FAQ Submittal form for us to add your question in our FAQ with our answer SSS gt AY Socket ATTENTION Incorrect BIOS Setup LGA775 CPU Socket 775 If you do not know how to handle BIOS setup or how to set it up properly it is strongly advisable that you do not modify any of the settings than otherwise instructed in the User s Quick Start Card Even a seemingly small incorrect adjustment DDR2 Al DDRII Channel 1 Memory Socket or modification in the BIOS setup can render your system unstable or unusable The incorrect BIOS setup is not covered DDR2 B1 DDRII Channel 2 Memory Socket by your motherboards manufacturer waranty D Motherboard Layout paeatet Port Y Clear CMOS JCMOS yo Clear CMOS Normal J 4 Line In RearOut Mouse gt GB SOOUOOOOCUOL fe d Line Out Front Out JCMOS l Le Mic In Center amp q Keyboard Cs we ie ay i lt Subwoofer O 3 A A A a Defaul COM Port Header COM2 Front Audio Header CFPA Se Mes i JN 1 6 DSR__ 4 5V Rear_Line Out FR y G vdi 3 s CTS 4 9 R_L NIGD NPXIY Rear_Line Ourt FL Coooooccooooco og USB 4 5 Header CUSB3 ppocoppocaog 5 2
Download Pdf Manuals
Related Search