Info - Adasat
Contents
1. STRONG DIGITAL TV Digital Free To Air Satellite Receiver SRT 6020 User Manual C 90 240 V CN 50 60 Hz Max 20 W Fixed O TELEVISION r Satellite Figure 6 Fixed Satellite Dish 1 ex pointed at Astra Figure 3 Fixed Satellite Dish 2 ex pointed at Q HotBird TELEVISION Figure 7 Satellite Dish on motorized Positioner Figure 4 DIGITAL AUDIO AMPLIFIER SPDIF Qamma Ox Sa 60 EE Er Figure 5 Figure 9 PART 1 English STRONG DIGITAL TV TABLE OF CONTENTS 1 0 INTRODUCTION 2 1 1 Safety Instructions 2 1 2 Storage 2 1 3 Equipment Set up 3 1 4 Features amp Accessories 3 2 0 YOUR RECEIVER 4 2 1 Front Panel 4 2 2 Rear Panel 4 2 3 Remote Control Unit 5 3 0 CONNECTIONS 6 3 1 Connecting to TV amp VCR 6 3 2 Connecting to Digital Audio Amplifier 6 3 3 Connecting to Satellite Dish 6 3 4 Connecting to serial cable for downloading software 7 4 0 STARTING UP 7 4 1 Language Selection 7 4 2 Select Satellite 7 4 3 Antenna mode 7 5 0 MAIN MENU 8 5 1 Channel Organiser 8 5 3 System setting 10 5 4 Timer 13 5 5 SD Card 14 6 0 WATCHING TV AND LISTENING TO THE RADIO 15 6 1 Program Information 15 6 2 MOSAIC Nine picture view 16 6 3 EPG Electronic Program Guide 16 6 4 Changin2. the batteries and if exhausted replace the batteries in the remote control www strongsat com 17 STRONG PART 1 English DIGITAL TV A 2 SPECIFICATIONS Demodulator Modulation Input Symbol Rate QPSK 2 45 Ms s SCPC amp MCPC signals from C amp KU Band satellites Video Decoder Profile level Input Rate Video Resolution Aspect Ratio Audio Decoder ISO IEC 11172 LAYER I amp II Sampling rate Audio modes Tuner Front End Input Frequency Range RF Input Level LNB Power DiSEqC Version System and Memory Flash Memory SDRAM RF Modulator Ouput channels TV Standard Connectors SAT IN SAT OUT ANT IN TO TV MPEG 2 MP ML Max 60 Mbits s 720 x 576 PAL 720 x 480 NTSC pixels 4 3 16 9 32 44 1 48 kHz Stereo Joint stereo Dual mono Mono DVB S 950 2150 MHz 25 65 dBm 13 18 V DC 5 Max 500 mA Overload protected 1 0 amp 1 2 16 Mbits 64 Mbits PLL CH 21 64 PAL BG 1 DK 2 SCARTS TV RGB CVBS VCR CVBS S PDIF coaxial output S VIDEO output Data Interface serial port RS 232 9 Pin D Sub Male type Separate power switch SD Interface 18 www strongsat com PART 1 o English STRONG General Data Input Voltage Range DIGITAL TV 90 240 V AC 50 60 Hz Power consumption max 25 W Stand by Power consumption lt 8 W Operating Temperature 0 C 40 C Storage Temperature 30 C 80 C
3. Move Dish and adjust position of the dish by pressing the LEFT RIGHT button Once you adjust the dish position choose Store position set number of the position by pressing LEFT RIGHT button Then choose NEXT and press the OK button The Channel Setup menu will appear c Dish mounted on GOTO X motor Set Antenna mode to GOTO X choose NEXT and press the OK button The menu Adjust antenna will appear Select transponder receivable at your location choose Transponder field and select transponder by pressing LEFT RIGHT buttons Then choose field My Longitude and using numeric buttons enter value of your longitude Use LEFT RIGHT buttons to select hemisphere East or West Then choose field My Latitude and using numeric buttons enter value of your latitude Use LEFT RIGHT buttons to select hemisphere Nord or South Choose field Goto Position and press OK Your dish will be turned to the position of satellite Then choose NEXT and press the OK button The Channel Setup menu will appear Choose NEXT and press the OK button to start the scan When the scan is completed the receiver will save the services information automatically and exit to the normal play state 5 0 MAIN MENU All the important settings and features of your receiver can be operated in Main Menu The Main Menu consists of five sub menus which are Channel Organizer Installation System setting Timer and SD Card Press the MENU key when the menu is off The M
4. PC to STB Connect the computer to the receiver receiver must be powered off with a 9 pin cross cable two females The computer will follow the steps below Start gt Programs gt Accessories gt Communications gt Hyper terminal Then choose COM1 or COM2 according to the computer port you are using and port setting as follows Bits per Second 115200 Data bits 8 Parity None Stop bits 1 Flow Control None In Hyper Terminal menu select Transfer item and then press Send file item Select the file with the new software UPD you want to download and choose the protocol 1K Xmodem Finally press OK and a download menu will appear in the computer screen Power on the receiver then the download process will begin After about 2 5 minutes the message OK Reset will appear on the computer on Hyper Terminal window which means the download has been completed successfully Power off the receiver and then unplug the RS 232 interface NOTE INCORRECT OPERATION MAY CAUSE UNREPAIRABLE DAMAGE TO THE RECEIVER 1 DO NOT POWER OFF THE RECEIVER DURING THE PROCESS OF DOWNLOAD 2 DO NOT PLUG IN OR UNPLUG THE RS 232 INTERFACE WHEN RECEIVER IS POWERED ON 5 4 Timer You can set the timer to make the receiver perform designated actions including timer based wake up or sleep instructions to the receiver Use the UP DOWN buttons to select timer Press the RED key to activate inactivate current timer Press the OK button
5. and confirm it again the system PIN will be changed to the new PIN 5 3 4 System info The system information displays information about your receiver such as software and User Interface version Compare the software version with the available in the internet in order to know if you have the latest version 5 3 5 System Update In this menu you can select between STB to STB and OAD m STB to STB software transfer a First power off both STBs connect them with cross RS 232 b Then power on master STB master is STB from which you will copy software and keep slave STB off Navigate in the menu of master STB and select System Update STB to STB c When the status displays detecting slave STB power on slave STB after the master STB detects the slave the master starts transmission and burns d While transmitting and burning it is very important to avoid other operations such as power off because this may cause destruction of the data in the FLASH memory and the receiver will need to be repaired e When update is complete first power off both STBs then disconnect the RS 232 line m Over Air Download OAD Select this option in order to update your receiver with the latest software version Software update service is available from satellites Astra 1C 1E 1F at 19E and Hotbird 1 2 3 4 at 13E Ifyour antenna is primed to Astra 1C 1E 1F at 19E then enter following parameters Frequency 12603 Polarity H Horizo
6. the receiver what to do with the received information Satellite receivers normally use four types of PID these are V PID video PID A PID audio PID P PID Program PID and data PID EPG information Personal Identification NumberA four digit code that is used for locking unlocking e g with the parental control feature Allows several programmes to be fitted into the same frequency band The signals from a satellite are transmitter either with linear vertical or horizontal polarization or circular right or left polarization Serial data port www strongsat com 19 STRONG PART 1 English DIGITAL TV 20 www strongsat com
7. to enter your selected timer settings Action You can select the following functions Power On The receiver powers on at the designated date and time within defined channel Time interval The receiver switches on at the designated date and time displays the channel and then switches off at the designated date and time The value set at the end time Power Off The receiver powers off at the designated date and time Cycle You can set the cycle ofthe action designated in the timer mode One time Daily or Weekly Start Date You can set the start date ofthe timer action Start Time You can set the start time of the timer action End Time You can set the end time of the channel viewing when the Timer mode is on Time Interval Channel Type Select between TV and Radio Channel name Press the Right button to display the channel list and using the navigation buttons select the channel to be shown when the receiver will power on by the timer 13 www strongsat com STRONG PART 1 o English DIGITAL TV 5 5 SD Card To watch you photos or play music from SD card enter to menu SD Card This menu consist two submenus JPG Guide and MP3 Guide Please insert you SD card into SD card slot before entering to the menu 5 5 1 JPG Guide The receiver supports photos in JPEG format Maximum supported resolution of the picture is 10 Mega pixels 24 bit colour depth While entering JPG Guide menu the screen with Folder
8. AIN MENU screen will appear 5 1 Channel Organiser In the MAIN MENU screen press UP DOWN to move the cursor to Channel Organiser and then press OK to enter the Channel Organiser menu which consists of two sub menus Channel Manager and Favourites Manager 5 1 1 Channel Manager In this menu you can change the order of the channels move delete and edit channels To change the satellite use the RED button Sort GREEN buton You can sort the channel order in the channel list by Name a z Name z a Free CA Fav NO Fav or Default type m Edit YELLOW button Select the channel that you wish to edit press the YELLOW Edit button to move into the modify program menu In this menu you can modify the Program Name Down Frequency Symbol rate Video PID Audio PID If you want to rename the channel use the UP DOWN keys to select Program Name and press OK the Program Name dialog will be shown www strongsat com PART 1 English STRONG DIGITAL TV Use the LEFT RIGHT buttons to move the cursor to the character you wish to edit Use the UP DOWN buttons to change character scroll alphabet If you wish to delete character you have to replace it with space character When editing is complete press the OK button Move channel Press the UP DOWN keys to point the focus of the menu to the channel of your selection Press the LEFT RIGHT keys to point the focus of the menu to the c
9. OUT connector of your VCR to the ANT IN connector of your TV set with a coaxial cable 3 2 Connecting to Digital Audio Amplifier The Digital Audio Amplifier is connected with the receiver from the S PDIF connector FIGURE 5 3 3 Connecting to Satellite Dish Connecting a fixed satellite dish to your receiver Fig 6 First choose a satellite you want to receive your signals from and have your dealer aim your dish at the requested satellite Connect a coax cable to your LNB and the other end directly to the LNB IN connector of your receiver Connecting multiple fixed dishes to your receiver using a DiSEqC 1 0 switch Fig 7 If you want to watch programs from more than one satellite For example from Astra and from HotBird it is advisable to use fixed dishes and a DiSEqC 1 0 switch Have your Dealer aim the dishes at the requested satellites and connect the LNB s with coax cables to the IN connectors of the DiSEqC 1 0 switch Connect the OUT connector of the DiSEqC 1 0 switch to the LNB IN connector at the back of your receiver Connecting a dish on a motorized positioner to your receiver Fig 8 Another possibility for watching programs from multiple satellites is by mounting a dish to a motorized DiSEqC 1 2 positioner Have your dealer mount the dish to the positioner set the correct angle of the elevation and let him set the center point for your positioner Connect the LNB with a coax cable to the LNB IN connector of the positioner and
10. Operating Humidity Range 10 85 RH Non condensing Size WxDxH in mm 260 x 210 x 40 Weight 1 2 kg A 3 GLOSSARY OF TERMS C Band DiSEqC EPG Fixed Dish Free To Air broadcast Ku Band LNB MPEG Network PAL Parental lock PID PIN Code Polarization RS 232 3 7 4 2 GHz Frequency Digital Satellite Equipment Control Electronic program guides that are transmitted by a broadcaster from a particular satellite to display information guide about a program content A dish antenna that is aimed at one particular satellite Unscrambled broadcast which you can view for free 11 13GHz Frequency Low Noise Block down converter The LNB is an electronic unit mounted on the satellite dish It receives the signals reflected by the dish and converts them to signals that can be used by Satellite receiver The Moving Picture Experts Group is founded by the ISO MPEG is a standard method for digital transmission of video and audio A network which is also known as a bouquet is a set of channels that is offered by a single broadcaster Referring to the Phase Alternate Line colour system adopted by European broadcasters This function gives you the possibility to lock other several functions of the receiver to prevent unauthorized users such as children to view channels that are not suitable for them A PIN code is required to use of the parental lock The transmitted packages have identifiers PID that tells
11. T RIGHT to select the satellite Ifthe satellite does not exist in the satellite list please select NEW SAT1 After selection of a satellite from the satellite list the Configure Antenna menu will appear please set the LNB Type LNB Low Freq LNB High Freq Band control Polarisation control DiSEqC Switch and Antenna mode Future steps of installation are described in 4 2 m Edit satellite Ifthe parameters of the satellite were changed or the satellite is a new satellite you must set the parameters of the satellite such as LNB type LNB low Freq LNB High Freq Transponder LNB Power 22k Tone DiSEqC and Antenna Mode Sequence of editing of satellite parameters is same as sequence of Add satellite and described in 4 2 www strongsat com STRONG PART 1 o English DIGITAL TV m Delete satellite If you want to delete a satellite press the YELLOW key Then a warning message will appear Select OK and press the OK button to confirm 5 2 2 Auto Scan Press the GREEN key to set the scan mode to Free or Free Scrambled If mode is Free only Free to Air channels will be added to the channel list If mode is Free Scrambled all channels from selected satellite will be added to the channel list Press the YELLOW Key to set the Blind Scan to ON or OFF Blind scan function is useful to scan new added satellite but scan may take long time Press the BLUE Key to set the scan type to NIT OFF or NIT ON while Blind Scan is set t
12. connect the OUT connector of the positioner to the LNB IN connector at the back of your receiver 6 www strongsat com PART 1 o English STRONG DIGITAL TV 3 4 Connecting to serial cable for downloading software Connect the RS 232 connector on the back of your receiver to the Serial port of your computer using a serial cable Instructions how to download software can be found on our website www strongsat com support gt download However this receiver can download new system software automatically by satellite Fig 9 4 0 STARTING UP Ensure that your satellite receiver is correctly connected to your television and dish and that your satellite signal is of good quality Ifyou are not sure about this then ask your local strong dealer to check your installation or satellite signal Confirm that the power plug on the receiver is plugged into the wall outlet Turn on the receiver The following picture is shown the first time you switch on the receiver It is recommended that you perform the first time installation following the Installation Wizard step by step It will help you to easily achieve system configuration and channel installation Ifyou are a professional installer then you can skip wizard by pressing MENU button and set up channels using the Installation menu 4 1 Language Selection Press UP DOWN to choose your language press OK to confirm The Select Satellite menu will appear 4 2 Select Satellite Future i
13. ess OK or Right to enter the language list and Press UP DOWN to select the language Press OK to confirm 10 www strongsat com PART 1 o English STRONG DIGITAL TV 5 3 1 2 TV settings You can set the TV mode Screen mode Video output and Modulator setting TV mode In TV mode Screen press OK or RIGHT to select mode press OK to confirm If you don t know which standard your TV has please select AUTO m Screen mode In TV format Screen press OK or RIGHT to select 4 3 or 16 9 press OK to confirm m Video output Press OK or RIGHT to select CVBS RGB or S Video press OK to confirm WARNING if RGB is selected then S Video output is OFF m Modulator setting The modulator setting screen will appear Use UP DOWN to select RF Audio mode or RF channel Use LEFT RIGHT to change the settings and press OK to confirm the settings or EXIT to cancel 5 3 1 3 Time Settings If a broadcaster provides GMT you can set the time using GMT or set your own time by yourself If the GMT usage is ON then you have to set the Time Zone If you set GMT Usage to OFF Set Data and Set Time item are displayed To set the time value manually move the cursor to the time item and use the numeric buttons on the remote control 5 3 1 4 Set Factory Default Please be careful when using this function because it will erase all the data and parameters you may have set earlier to your receiver Once you set the factory default you will have to re install y
14. g channel list mode between TV Radio and Favourite 16 6 5 Selection Audio Language 16 6 5 TELETEXT function 16 6 6 Subtitles function 17 A 1 TROUBLESHOOTING 17 A 2 SPECIFICATIONS 18 A 3 GLOSSARY OF TERMS 19 HOTLINE 20 400150 0 12 Min from German and Austrian wired line www strongsat com STRONG PART 1 o English DIGITAL TV 1 0 INTRODUCTION 1 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER m In a closed or poorly ventilated cabinet directly on top of or under any another equipment on a surface which might obstruct the ventilation slots DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES m To direct sunlight or near any other equipment that generates heat to rain or intense moisture to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects such as loudspeakers transformers etc m Do not use a damaged power cord lt may cause a fire or an electrical shock Do not touch a power cord with wet hands It may cause an electric shock m Never open the cover It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical hazards Your warranty will be void ifthe receiver has been opened m When the receiver is not used for a long period of time you should unplug the power cord from the wall socket m Do not use alcohol or ammonia based liquids to clean the receiver If you wish you may clean your receiver with a s
15. her If mode is Intro then only first 10 seconds of each file will be played Repeat All use LEFT RIGHT to select ON or OFF If you selected ON then playing will be looped continuously until interrupted If you selected OFF then each file will be played once 6 0 WATCHING TV AND LISTENING TO THE RADIO 6 1 Program Information In normal operation status no menu operation press the INFO button The program information banner will be displayed at the bottom of screen From program information banner you can read channel number channel name current and next program name if available from broadcast and current time To check technical information about channel press INFO button twice the Program Information menu will appear on screen as show on lt Screen44 gt In this menu the user can view the current program information such as the satellite name program name program number local frequency polarity 22K tone DiSEqC down frequency symbol rate video PID and audio PID You also can view the signal strength of the current program and its signal quality 15 www strongsat com STRONG PART 1 o English DIGITAL TV 6 2 MOSAIC Nine picture view In normal operation status no menu operation press the MOSAIC button there are nine picture being shown on screen 6 3 EPG Electronic Program Guide The EPG shows a program schedule of the channels NOTE not all broadcasters provide program information From norma
16. l view mode press the EPG button The EPG Menu will appear Press UP DOWN to choose the channel Press RIGHT to display programs schedule of the current channel 1 In EPG program schedule menu Press the UP DOWN keys to choose the program items Press LEFT RIGHT keys to get programs schedule for previous next dates Press EXIT to return to EPG Menu Press GREEN to display the details of the current program 2 In program details Press UP DOWN to scroll information next previous page Press LEFT or EXIT to return to the EPG schedule Menu Programming Timer from EPG You can set up the event timer by pressing RED button or OK button from the EPG program schedule To set up a timer event Press UP DOWN to move the cursor to the program for which you want to add a timer Press RED button to add a timer You can also use this screen to modify each value To save the settings press OK To quit event timer setup press EXIT 6 4 Changing channel list mode between TV Radio and Favourite To change between TV and Radio channel lists use TV R button from normal operation mode or from channel list mode To change channel list to favourite mode press FAV button from normal operational mode Use LEFT RIGHT buttons to select favourite group Press OK to confirm selection Then select channel of your choice and press OK to switch to full screen mode If you wish to select another favourite group of channels or exit from favourite channel list mode pres
17. list and Picture list will appear Navigation in folder list Use UP DOWN buttons to select folder Use OK to open folder Use GREEN button to go to Upper folder Use LEFT RIGHT button to select folder list or file list left or right panel m Navigation in the picture list Use UP DOWN buttons to select Use OK to watch picture Use RED button to switch to full screen view USE GREEN button to go to upper folder User YELLOW button to start slide show Use BLUE button to delete file current displayed file Current displayed file is marked by finger symbol You will be asked to confirm operation m Watching pictures To watch picture on screen select file with picture and press OK button Picture will be shown at background Press List RED button to remove folder list from screen and watch picture in full screen mode In picture watching mode Use UP DOWN buttons to go to next previous picture Use RED or Exit button to return to folder list m Slide show To start slide show press YELLOW button while menu focus is at Picture List Slide Show setup menu will appear Slide Delay use LEFT RIGHT to select how long you want to display each picture before it will be changed to the next one Repeat All use LEFT RIGHT to select ON or OFF If you selected ON then slide show will be looped continuously until interrupted If you selected OFF then each picture will be shown once After selection of slide show options select OK and press OK Duri
18. ng Slide Show Use UP DOWN buttons to force slide change to next previous Use PAUSE button to delay current slide on screen as long as you wish To resume slide show press PAUSE button again Use EXIT button to stop Slide Show 14 www strongsat com PART 1 English STRONG DIGITAL TV 5 5 2 MP3 Guide MP3 Guide allows you to play music in MP3 format from your SD card Supported bit rates are up to 320 kbit s variable bit rate is supported While entering MP3 Guide menu the screen with Folder list and Playlist will appear m Navigation in folder list Use UP DOWN buttons to select folder Use OK to open folder Use GREEN button to go to Upper folder Use LEFT RIGHT button to select folder list or file list left or right panel Navigation in the play list Use UP DOWN buttons to select file Use OK or RED to play file USE GREEN button to go to upper folder User YELLOW button to setup play list parameters Use BLUE button to delete file current file You will be asked to confirm operation Playing a single file Select file that you want to play and press OK or RED button Use UP DOWN buttons to select previous next file to play Use LEFT RIGHT button to adjust volume Use OK or RED button to stop file play Use GREEN button to pause file play Setup of Play List Press YELLOW button to setup Play List Play mode use LEFT RIGHT to select between Sequential and Intro If mode is Sequential then files will be played one after anot
19. nstallation steps are depending from satellite where your dish is aimed a Your dish is aimed to Astra 1C 1E 1F or Hotbird satellite Press UP DOWN to select the ASTRA or Hotbird satellite and press OK button on your remote control Follow instruction written on screen When you have fixed your dish at correct direction choose NEXT and press the OK button The Channel Setup menu will appear b Your dish is aimed at another satellite Select Other in Select satellite menu and press OK more satellites will be listed If you select a satellite in the satellite list the Configure Antenna menu will appear please set the LNB Type LNB Low Freq LNB High Freq Band control Polarisation control DiSEqC Switch and Antenna mode 4 3 Antenna mode a Fixed dish Set Antenna mode to Fixed select NEXT and press the OK button The Adjust antenna screen appears select transponder receivable at your location and adjust the antenna position for maximum level for the signal strength and quality When you have completed the adjustment choose NEXT and press the OK button The Channel Setup menu will appear b Dish mounted on DiSEqC 1 2 motor Set Antenna mode to DiSEqC 1 2 choose NEXT and press the OK button The menu www strongsat com STRONG PART 1 o English DIGITAL TV Adjust antenna will appear Select transponder receivable at your location choose Transponder field and select transponder by pressing LEFT RIGHT button Then choose field
20. ntal Symbol rate 22000 Ifyour antenna is primed to Hotbird 1 2 3 4 at 13E then enter following parameters Frequency 12476 Polarity H Horizontal Symbol rate 27500 Move menu focus to OK and press OK button on remote control The receiver will check availability of the software update on air and load the latest software if available Do not switch power off and do not disconnect the receiver from the aerial during update process Availability of the software update is subject of local broadcast condition and may not work in all countries Contact your vendor to find out more about this function m Update from SD card First you need to store the file with extension crd to the root folder of the SD card File with software update can be downloaded from our web site www strongsat com Insert the SD card with crd file to the SD card slot of the receiver Go to menu System Setting System Update Select SD Card Data and 12 www strongsat com PART 1 English STRONG DIGITAL TV press OK On the left side ofthe screen you will see the list of folders at the right side you will see the list of files in root folder Use UP DOWN buttons to select file with software update and press OK Confirm the update The message Updating software from SD card Please wait will appear on screen Receiver will reboot automatically once the update is finished NOTE Do not eject SD card during software update process m Update through
21. o OFF and to Quick Search or Detail Search while Blind Scan is set to ON When the set up is completed press the RED key to start the scan 5 2 3 Manual Scan In this menu you can scan single transponder add a new transponder edit the transponder or delete the transponder You can switch between satellites with the RED button m Scan transponder Use UP DOWN buttons to select the transponder Press OK button to start the scan m Add Transponder In this menu you can add a new transponder to the system Press the GREEN button the Add Transponder sub menu will appear on screen Frequency input the frequency of the new transponder Symbol Rate input the symbol rate of the new transponder Polarity Select the Polarity of the new transponder Edit Transponder In this menu you can edit a transponder in the system Press the YELLOW button the Edit Transponder sub menu will appear on screen This menu is similar to Add Transponder menu Delete Transponder Press the BLUE button to delete a transponder You will need to confirm operation Press LEFT RIGHT to select OK press the OK button to confirm 5 3 System setting In this menu you can configure the systems such as Language Setting OSD Style Parental Control TV Settings and Time Setting 5 3 1 Preference 5 3 1 1 Language Setting You can change the language of the OSD preferred Audio and Subtitles Use UP DOWN to select the OSD language Audio language or Subtitles language Pr
22. oft lint free cloth slightly made damp with a mild soap solution only after disconnecting from the mains voltage supply Make sure no foreign objects fall through the ventilation slots because this could cause fire or an electric shock m Do not place any objects on top of the receiver because this might prevent proper cooling of the components inside Safety Precautions m Do not open the receiver cover as you will be exposed to a shock hazard It will also void your warranty Refer all maintenance or servicing to suitably qualified personnel m When you are connecting the cables be sure that the receiver is disconnected from the mains supply voltage Wait a few seconds after switching off the receiver before you move the receiver or disconnect any equipment m lt is a necessity that you only use an approved extension and compatible wiring that is suitable for the electrical power consumption of the installed equipment Please ensure that the electrical power supply corresponds with the voltage on the electrical identification plate at the back of the receiver Ifthe receiver does not operate normally even after strictly following the instructions in this user manual it is recommended to consult your dealer 1 2 Storage Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture When unpacking it make sure that all the parts are included and keep the packaging away from child
23. olumn Move When the focus is on column Move press the OK button to confirm selection of the channel using the UP DOWN buttons move the channel to its new location and press the OK button to confirm the new location Repeat this for every channel that you want to move Delete channel Press the UP DOWN keys to point the focus of the menu to the channel of your selection Press the LEFT RIGHT keys to point the focus of the menu to the column Del When the focus is on column Del press the OK button to mark the channel as selected to be deleted from the list To apply the changes press the EXIT button and confirm the channel s deletion Delete all channels To delete all channels from current satellite press BLUE button Dell All You will be asked to confirm operation 5 1 2 Favorites Manager Press the UP DOWN keys to select the channel Press the LEFT RIGHT keys to point the focus to the favorite group Press the OK button to add the selected channel to the Favorite group To remove the channel from the favorite group repeat same operation 5 2 Installation The installation menu contains three sub menus Antenna Installation Auto Scan and Manual Scan 5 2 1 Antenna Installation You can add a satellite edit a satellite and delete a satellite in this menu m Add satellite Ifyou want to add a new satellite press the RED key in this menu a satellite list will appear on the screen Press LEF
24. on of the receiver Check the receiver according to the procedures shown below If the receiver does not work properly after checking it please contact the dealer Don t open the receiver cover This may cause a dangerous situation Symptom Cause Remedy front panel does The display on The power cord is not plugged in Check that the power cord is plugged in to the wall outlet tuner parameters Incorrect values of some Wrong direction ofthe dish not light up No picture or Wrong connection of the Audio Connect the Audio Video output of the sound Video output of the receiver to TV receiver to TV correctly Audio muting Press the Mute button TV power off Turn TV on No picture The receiver can t receive the Check the antenna cable replace the signal cable or connect the cable to the receiver tightly Set the values of the tuner parameters correctly in the installation menu Check the signal strength with a spectrum analyzer and adjust your dish correctly Power Overload your cable system displayed on TV Message Antenna Receiver detected short cut in Disconnect receiver from main power Check your cable system Remove short cut Replace LNB Restart receiver exhausted The remote control The batteries of the remote does not work controller are not inserted or Check whether the batteries are inserted correctly in your remote control Check
25. our preferences and re scan your channels To reset your receiver to factory default apply the following steps Select Set Factory default and press OK Confirm warning message with OK and press the OK key the receiver will return to its factory default state and all user data will be deleted NOTE Your PIN code will change back to the factory setting 0000 5 3 2 OSD Style In this menu you can set the Menu Colour Transparency Level and Border Pattern 5 3 3 Parental Control In this menu you can set channel lock status ON or OFF the menu lock status parental setting and change the PIN code The default PIN code is 0000 m Channel Lock Set the system channel lock to ON or OFF Ifthe channel lock is on the user has to enter the parental PIN code correctly before watching the locked channel Menu Lock Press OK to select whether you need the lock or not for the Menu YES or NO press OK 11 www strongsat com STRONG PART 1 o English DIGITAL TV to confirm Ifthe menu lock is on then for some operations such as search program and set factory default you need to enter your PIN Parental Setting Set some channels to lock status If a channel is locked the user has to enter the parental PIN code correctly before watching the locked channel Use the UP DOWN keys to select the channel you want to lock Press the OK button to lock the channel Change PIN For modifying the PIN you must enter the 4 digits PIN
26. power switch m Set up support for first time installation m Max 4 800 channel memory capacity for 64 satellites m Astra and Hotbird channels pre programmed m 4 Favourite lists for TV and Radio programme m Quick and easy installation amp user friendly menu m Excellent Audio amp Video quality m Parental lock function for menu and selectable per channel m Teletext via OSD amp VBI m Supports DiSEqC 1 0 DiSEqC 1 2 and GOTO X m Electronic Programme Guide EPG for present following event information and up to 7 days for on screen programme information m Full multi lingual DVB subtitling and audio track support m Multi lingual support on screen menu OSD English German French Italian Spanish Russian Croatian Romanian Hungarian Czech Polish m Edit functions for TV or Radio programme name and satellite name Future proof Software update via satellite OTA m Signal strength bar for digital transponders m Automatic network and manual channel scan options Power on with last viewed channel www strongsat com STRONG PART 1 English DIGITAL TV m 10 Timer for recording and or sleep timer with 3 modes daily weekly once User friendly remote control with coloured function buttons m Low power consumption m Mosaic function 9 TV Channel in overview Accessories m User s Manual m Remote control unit m 2x Batteries AAA type NOTE The batteries should not be recharged disassembled electrically
27. ren When transporting the receiver from one place to another or if you are returning it under warranty make sure to repack the receiver in its original packaging with its accessories Failing to comply with such packaging procedures could void your warranty 2 www strongsat com PART 1 o English STRONG DIGITAL TV 1 3 Equipment Set up We recommend you consult a professional installer to set up your equipment Otherwise please follow the instructions below m Refer to the user manual of your TV and your antenna m Make sure that the SCART cable and outdoor components are in a good condition and the SCART connections are well shielded This manual provides complete instructions for installing and using this receiver The following symbols will serve as follow WARNING Indicates warning information TIPS Indicates any other additional important or helpful information MENU Represents a button on the remote control or the receiver Bold Character Move to Represents a menu item within a window Italic Character 1 4 Features amp Accessories m For all digital Free To Air TV and Radio programmes via satellite m SD Card reader for watching your photo album or music files on your TV supporting MP3 and JPG file format and software update m Display showing channel name or time m Automatic clock change summer winter time m Timeshift with 15 seconds play back m Digital sound through coaxial output S PDIF m Separate
28. s FAV button List of favourite channels will appear on screen Press RED or FAV button to move menu focus to selection of group Use LEFT RIGHT buttons to select group of your choice Select group NO FAV and press OK if you wish to exit from favourite channel list mode 6 5 Selection Audio Language Press the AUDIO button on the remote control to select the audio language Select the Audio Channel or Sound mode with UP DOWN buttons Select Audio channel number or Sound mode Stereo Left or Right channel Press OK to confirm your selection Your selection will be memorized for current channel Receiver will play last selected audio track every time when you select this channel in future NOTE Audio track with AC3 sign can be listened only if receiver is connected to digital audio amplifier and amplifier is ON 6 5 TELETEXT function From normal view mode press TEXT In TEXT on OSD press UP DOWN to add subtract displayed page number Press the Numeric keys to input the page directly 16 www strongsat com PART 1 o English STRONG DIGITAL TV 6 6 Subtitles function From normal view mode press SUB button If channel has subtitle information the subtitles language selection menu will appear Use LEFT RIGHT buttons to select between DVB and Teletext subtitles Use UP DOWN to select subtitles language Press OK to confirm your selection A 1 TROUBLESHOOTING There may be various reasons for the abnormal operati
29. se this coaxial output to connect your receiver to the input of your digital audio amplifier RS 232 Serial Port This serial port can be used to connect your PC with your receiver to download new 00 Ne versions of software to your receiver 10 Power ON OFF Switch 11 Power Cord Your receiver requires a current of 90 240V AC Auto selectable 50 60Hz 5 Make sure to check the power specification before connecting your receiver to the wall outlet 2 3 Remote Control Unit Turns the receiver On Off X Mutes audio output of the receiver AV Toggle between TV and AV mode 0 9 Changes channel and controls numeric functions FAV Toggle Favorite mode ON OFF TV R Toggle between TV or RADIO mode MENU Shows the main menu and exits from any level of menu to view mode INFO Shows information of the current channel EPG Shows the EPG Electronic Program Guide only when menu is off EXIT Exits from the menu or sub menu and cancels the progressing function if applicable AV Change the current program to the previous next program when menu is off Moves the cursor upwards downwards when menu is on gt Increases decreases the volume level when menu is off Change the setting values in specific menu item when menu is on OK Activates the highlighted menu item Displays a channel list according to TV Radio Mode V V To increase or decrease the receiver volume level P P Page up and down in menu list MOSAIC Shows pict
30. short circuited or be mixed or used with other types of batteries 2 0 YOUR RECEIVER 2 1 Front Panel Figure 1 1 Power On Off button 2 Channel Up Down buttons 3 Mode indicator The RED light indicates that the receiver is in STAND BY mode The GREEN light indicates that the receiver is in AWAKE mode 4 VFD display In STAND BY mode this indicates current time In AWAKE mode this indicates current channel name 5 SD card slot Insert your SD card to this slot to watch your photos play MP3 files 2 2 Rear Panel Figure 2 1 SAT IN Connect the digital signal from your LNB on the satellite dish to this connector 2 SAT OUT Gives you the possibility to connect an extra receiver analogue or digital 3 ANT IN To connect your aerial antenna or cable TV using coaxial cable 4 TO TV Ifyou do not use a SCART cable to connect your receiver to your TV or if you have connected a cable to the ANT input you will have to use this connector to connect the receiver to your TV by using a coaxial cable 5 TV SCART Connector To connect your receiver to your TV set using a SCART cable 6 VCR SCART Connector To connect your receiver to your video recorder using a SCART cable Your video signal 4 www strongsat com PART 1 o English STRONG DIGITAL TV will now be looped through your receiver to your TV set N S Video Connector To connect your receiver to your TV set using a S Video cable S PDIF Digital audio output U
31. ures of 9 channels simultaneously on the screen PAUSE Freeze Resume picture AUDIO Shows the list of available audio languages for the channel you are watching In addition it sets the current channel audio to stereo n left mono n or right mono n EDIT Program edit REPLAY Replay last 15 seconds of current channel TEXT Shows current service s Teletext on OSD SUB Show the list of subtitled languages the current channel supports RECALL Switches back to last channel viewed www strongsat com STRONG PART 1 o English DIGITAL TV 3 0 CONNECTIONS 3 1 Connecting to TV amp VCR Basic connection with a Scart cable Fig 3 1 Connect the satellite signal from the LNB to the LNB IN connector 2 Connect the TV SCART connector at the back of the receiver to the SCART IN connector on your TV set Advanced connection of the receiver to the TV set and VCR Fig 4 1 Connect the satellite signal from the LNB to the LNB IN connector 2 Connect the TV SCART connector at the back of the receiver to the SCART in connector on your TV set 3 Connect the VCR SCART connector at the back of the receiver to the SCART in connector on your VCR Optional m Connect a UHF coaxial lead or cable antenna lead to the ANT IN input connector at the back of the receiver m Connect a coaxial cable to the TO TV connector at the back of the receiver Connect the other end of this coaxial cable to the ANT IN connector of your VCR m Connect the TV
Download Pdf Manuals
Related Search