GMOS-JI100S-User-Manual
Contents
1. JI100 SERIES USER MANUAL Version 0421 2014 md www SpeedAngle com IMPORTANT PLEASE READ SpeedAngle Lap Timer is a device with high technology and powerful algorithm It is capable of calculating and producing lean angle measurement real time and then listing the results in the Angle History and the Max Angle fields However there are times when the real time lean angle measurement might be exaggerated such as when e You are maneuvering your bike in a way that is outside normal sportsbike motion such as moving the bike backwards having a highside lowside or pulling a wheelie etc e You are curving around a bend by turning your handle bar at a great angle especially at a low speed e The wheel hits an obstacle or a pothole and causes the bike to bounce e You are curving around a bend whose slope changes midway e The vibration is too much More often than not this is because the G force behavior is not one of normal bike movement or the long axis of the motorcycle body does not point to the traveling direc tion ahead due to twist The GMOS Core is constantly examining if such interaction exists every time a turn is completed If the answer is yes it will compensate the interac tion and re produce measurement results after the calibration As the records of the Angle History and Max Angle fields are updated after the calibration process while the pointer of the lean angle meter is in sync with the real time measureme2. displayed depends on which is designated as Main Display or Sub display You can control at what place the Timer is to start by setting a proper starting speed Here are a few suggestions e To start the Timer right close to where you are set the starting speed at 10 e To start the Timer after you exit the pit lane set it at about 90 or 120 depending how fast you ride e To start the Timer on a straight set the Starting speed higher than your corner ing speed such as 150 or more depending on how fast you ride To set the starting speed press MENU to enter Laptimer Menu To designate the speed unit switch to Drive mode and enter System Menu Data logging starts automatically and synchronically with the Timer No button press ing is needed All your GPS traces speeds G s angles and lap times will be recorded as a trace log SA file and your lap times a timer log SAL file Please note that if the memory is full during data logging GMOS will stop logging and display MEMORY FULL in the Message Area This will not affect any Timer functions Stopping Timer and Data Logging The Timer and data logging will stop automatically when it has been idle the speed staying at 0 for a pre designated period of time As data logging starts and ends synchronically with Timer you can control when the data logging is to end by setting a proper idle time Here are a few suggestions e To stop data logging right after a session ends s
3. A package without the issued shipping label or with an expired shipping label will be refused e Please send the GMOS device insured and postage prepaid or accept the risk of package loss or damage during shipment e The repaired or replaced GMOS device will be shipped back to you Please con tact your local customs office for information as to taxes duties or other broker age fees that may be applied to returned goods Once our service center receives your GMOS device we will either repair or replace the GMOS device at our option The removed or replaced parts or device are prop erty of SpeedAngle Inc Please remember to download the logs recorded on your GMOS device before you ship it to our service center It is very likely that the logs will be damaged or lost dur ing warranty service SpeedAngle will not be responsible for such damage or loss Warranty 32 MN SPECIFICATION Dashboard Dimension 2 4 4 4 0 8 61 5 mm 111 5 mm 20 mm Dashboard Weight 4 8 oz 1359 Sensor Dimension 0 7 0 3 0 15 17 mm 7 mm 3 6 mm Sensor Weight 0 7 oz 209 Power 3 7V Li lon battery Working Temp Range 36 F 140 F 2 C 60 C guaranteed LCD 132 64 STN display screen Refresh Rate 20 Hz Interface USB 2 0 compatible Battery Life Time 14 hrs without backlit and external GPS Antenna Logs 254 logs max Max Log Time about 7 hrs Log Resolution 20 pps for lean angle and G 10 pps for GPS and speed
4. Go back to your Start location Enter Laptimer Menu set FL Auto Set off and then select the Track you have just set Exit Menu GMOS will prompt the Track you designated in Standby Mode Now you are ready to go GMOS will start the Timer when you reach the starting speed and produce lap times when you ride past the Finish Line location Configuring the Timer In the Laptimer Menu you can e view the Lap Time Report of up to 14 latest logs e set FL Auto Set on off e designate a Track to use or to overwrite e designate the Timer starting speed e designate at what idle time the Timer is to stop e designate the width of the Finish Line e designate what is to be displayed as Main Display or Sub Display and e designate how long the Main Display and Sub Display are to be held after updated In the Laptimer Menu pressing SELECT will execute the function selected or adjust the value Pressing MENU will go to the next item Below we will show you how to configure the settings Using GMOS 24 Log Count Memory Left LAPTIMER MENU VIEW LATEST RECORD Press SELEGT to enter the list of your latest 14 logs They are listed in the order recorded with their date time and track setting mr e To view a log move to the entry ma and press SELECT You will see 7308 OT maps a summary of session duration 2 23 302 best lap and average lap infor 47 17 mation e Press SELECT on DETAIL to see the time top speed and 2 33 933
5. Set with Auto Set When GMOS is setting a new Track with Auto Set it marks the location where the staring speed is reached as a reference point uses the following 10 meter trace as a direction pointer and draws a line extending SOM om from the reference point to both sides perpendicular to your trace This is your Finish Line Then GMOS also marks your riding direction as the valid crossing direc tion of this Line This is to prevent unwanted Lap times when the Line is crossed from a wrong direction Then GMOS will go on to start the Timer How to Control Your Finish Line Location Finish Line As the location where the Finish Line is set depends on where the starting speed is reached you can control the location of the Finish Line by designating a proper Using GMOS 22 starting speed Here are a few suggestions e To set the Finish Line right close to where you are set the starting speed at 10 e To set the Finish Line on a straight set the starting speed above your cornering speed such as 150 or more depending on how fast you ride The key is to keep your speed below the designated starting speed until you reach your desired Finish Line location Stay Close to the Center Line aan When setting a Finish Line it is essential that you stay sefu close to the center line of the track This will ensure that PN the reference point is in the middle of the track so that the Finish Line will extend evenly to both sides a
6. available to provide sufficient GPS positioning data The GMOS GPS Core will continue searching for more satellites and will resume its function once the GPS signal reception improves Why was the GPS Antenna Icon not displayed When the GPS reception is poor it might take longer for the GPS Core to find enough satellites for GPS positioning The GPS Antenna Icon will reappear once the positioning is complete If you have not had the GPS external antenna installed please connect it with the dashboard to imcrease the reception sensitivity My GMOS can not record logs The reason might be that the GPS Core was positioning that the memory was full or that the number of logs recorded had reached 254 Please refer to page 14 for more information Why was the G force bar not back at zero when was riding at a constant speed Please check to see if the sensor is installed vertical to the ground securely A tilted sensor might affect G force and lean angle measurement If it stayed maxed out the indicator inside the G sensor was stuck Please give the sensor a few light taps and it will be back to zero Why was there no lap time produced when I passed through a Finish Line This might be that the GPS reception is not good enough when the Finish Line was being set automatically As a result the GPS position of the Line drifted away from the actual location To avoid such deviation try to set the Track when at least two of th
7. go on to en ter Timer Mode e To clear the logs you can either download and clear them with the Speed Angle R3 software or go to System Menu and select CLEAR MEMORY to clear them directly Temperature Alert flashes when the environmental temperature is below or above the operating temperature range of the sensor 36 F 140 F or 2 C 60 C flashes when the temperature is below 36 F 2 C while t flashes when the tempera ture is above 140 F 60 C e Environmental temperature below or above the sensor s operating tempera ture range might affect measurement accuracy Battery Icon indicates the charge of the battery e When the battery is almost empty a LOW BATTERY message will be prompted Please recharge GMOS as soon as possible LOW BATTERY PLEASE TURN OFF POWER TO PROTECT BATTERY Current Time indicates the current time of the preset Time Zone e To set the Time Zone please go to System Menu and select TIMEZONE 37 GMT G force Bar indicates the real time G A right going bar indicates acceleration while a left going bar deceleration e if the bar is not back at center when the bike is stationary the sensor is not horizontal Please adjust till the bubble of the bubble level is in the center circle Using GMOS 13 7 Lean Angle History lists the max angles of the last three turns Updated every time a new turn is completed A right aligned number represents a right
8. or is in Stand by Mode and then follow the procedure below e Press MENU to go to FL AUTO SET e Press SELECT to set it on or off To overwrite the Track with a new Finish Line set it ON To use the Track directly set it OFF e Press MENU to go to TRK e Press SELECT till you find the Track that you want Exit the Laptimer Menu GMOS will enter Standby Mode Now you are ready to start your session To use a Track directly Y l wz 12 30 LAPTIMER 12L T5 LEFT VIEW LATEST RECORD FL AUTO SET START TIMER STOP TIMER LINE WIDTH To overwrite a Track LAPTIMER 12L 75 LEFT VIEW LATEST RECORD FL AUTO SET ON 10 208 11 09 START TIMER STOP TIMER LINE WIDTH Using GMOS 20 26 90KMH 20s IDLE 100M Exit the Exit the Menu Till TZA 12 30 TOP h or SACUIT FULL TIMER STARTS AT 90KMH 10_08_11 09 26 TIMER STARTS AT 90KMH Starting Timer and Data Logging Start your session when GMOS is in Standby Mode Ride along Once the starting speed is reached GMOS will set a new Finish Line if designated to and go on to start the Timer automatically It will then use the Track newly set or the Track se lected to produce lap times down to 1 1000th of a second sector times if you have sector Lines uploaded via Track Manager session time last lap best lap with time gap or lap length every time a Sector Line Finish Line is crossed What will be
9. turn angle degree while a left aligned number a left turn angle degree e Lean angle degrees less than including 15 will not be displayed in Lean Angle History Max Right Left Angle shows the max right left lean angle degrees measured since GMOS is pow ered on e Lean angle degrees less than including 15 will not be displayed in Max Right Left Angle e To clear the record please go to System Menu and select RESET MAX ANGLE Lean Angle Meter shows real time lean angle up to left right 69 degrees Message Area displays messages about log recording The message will be displayed for about 2 seconds There are five messages that may appear in the Message Area START LOGGING END LOGGING displayed when GMOS starts ends data recording This is an additional reminder besides the REC icon POSITIONING displayed when SELECT is pressed to start recording but there are not enough satellites to provide all the GPS positioning data necessary for starting a new log such as location time and date The system will continue search ing for more satellites Sometimes this may take up to a few minutes During this process the GPS Antenna Icon will not be displayed When you see the GPS Antenna Icon reappear press SELECT to start recording Using GMOS 14 MEMORY FULL displayed when SELECT is pressed to start recording but the system memory is already full or during data logging when the memory is full I
10. way to use the SpeedAngle Timer is turn the power on and then do nothing unless you have multiple settings available for the track and need to choose one Just focus on your ride It will take care of itself Be Using GMOS 17 low we will show you how the SpeedAngle Timer works for your information Knowing the Buttons In Timer Mode and Laptimer Menu pressing the button will e MENU enter Laptimer Menu or go to the next item e SELECT adjust the value of the menu item or execute the function GPS Positioning Once you enter Timer Mode the system will check the GPS signal quality and display GPS IS POSITIONING until more than 4 satellites are locked During this process you can press MENU and enter Laptimer Menu to edit your settings GPS IS POSITIONING PLEASE WAIT e If you designate a Track at this moment GMOS will skip the Auto Search proce dure that is to follow and use the designated Track directly Auto Search After GPS positioning is complete GMOS will search for tracks by Auto Set or preloading whose Finish Lines are within 3KM of your loaction If no Track is found GMOS will prompt NO TRACK FOUND on the screen If there are any Tracks found GMOS will list up to 6 of them as the search result along with a SET NEW option za 12 30 TOP SEARCH ee SEARCH RESULT SACUIT WEST SACUIT EAST SET NEW SACUIT WEST NO TRACK FOUND 08_25_12 14 38 SET NEW PRESS ANY KEY TO SET A NEW TRACK
11. 164 124 average speed of every lap in 2 34 859 161 124 G LAPTIMER 12L 75 LEFT ZA 0725 1330 LOSAIL za 12230 3 08 311 123 82 2 56 972 156 107 2 33 311 165 125 A 2 32 502 166 125 this log PG UP EXIT e To exit press MENU to move to EXIT and press SELECT to confirm FL AUTO SET Press SELECT to turn FL Auto Set on or off Turn it off if you would like to use the settng of an existing Track otherwise please leave it on TRK 01 09_25_11 14 38 Press SELECT to rotate among the 15 Tracks avail able The one listed is the one GMOS will use e By default a Track is named by the date and time the Finish Line is set MM_DD_YY hh mm To name it otherwise please use the Track Manager software START TIMER Press SELECT to choose a speed at which GMOS is to set a Finish Line start the Timer and start log recording You can choose a value between 10 and 240 by an increment of 30 e For how to choose a proper starting speed please refer to Tips on Setting a Better Finish Line P 22 Using GMOS 25 STOP TIMER 10s IDLE LINE WIDTH BEST LAP FREEZE TIME GO TO DRIVE MODE EXIT TO TIMER Press SELEGT to choose the length of time the Timer is to be idle for before GMOS stops the Timer and log recording You can choose a value among 0 10 20 30 and 180 e You can stop the Timer any time by pressing either of the keys If you press MENU GMOS will stop the Timer AND enter Laptimer
12. ECT If you were in Timer Mode when you turned off GMOS last time the system remembers it and will enter Timer Mode directly after the Liability Screen The Timer Mode screen looks like Sub Display Displaying best lap with time gap sector time last lap Lap Number Flashes when a Finish Line ts crossed Main Display Displaying lap time session time Highlighted when a best lap is created if Sub Display best lap The upper half is the same as Drive mode displaying top speed current speed and longitudinal G Angles are not displayed The lower half consists of three compo nents Main Display Sub Display and Lap number The GMOS lap Timer is developed with convenience in mind It features e Auto Track Search searching for Track settings either by Auto Set or by preloading within 3KM automatically after GPS positioning is complete e Auto Finish Line Setup drawing a Finish Line automatically where the Timer starting speed is reached e Auto Timer Start Starting the Timer automatically when you reach the pre set starting speed e Auto Timer Stop stopping the Timer automatically when it has been idle for a pre set length of time e Auto Data Logging data logging starting and stopping automatically with Timer e Auto Lap Time Report Display displaying the record of your newly finished laps once the Timer stops and back to Timer automatically once you reach the starting speed again With so many auto features the best
13. Lap Timer Resolution 1 1000 second GPS Antenna built in and external GPS Update Rate 10 Hz GPS Sensitivity 159 dBm tracking GPS Channels 32 all in view GPS Start Time 36 sec average GPS Speed 255 MPH 410 KMH max Longitudinal G Range 1 5 G Lean Angle Range R L 69 C FE Features and specifications subject to change without notice Please visit www SpeedAngle com for the latest update Copyright 2014 SpeedAngle Inc All rights reserved Specification 33
14. MOS dashboard unit to your PC to have the logged data downloaded Our user friendly software SpeedAngle R3 makes it easy to relive your ride on the computer with the lean angle G and track sectors mapped onto your GPS traces Open the graph plot in lean angle G force or speed or open your lap time report to have your ride further analyzed You can GMOS Overview 2 load one log at a time or load up to 5 logs and have them replayed simultaneously to have a virtual race This allows you to have a deeper insight into your riding style and skill find your braking points and best line or even compare your ride with oth ers for further improvement GMOS at a Glance Your GMOS comes with a dashboard unit and a sensor The dashboard unit re ceives GPS signals processes and stores the data transmitted from the sensor and communicates with the computer The sensor is responsible for sensing the lean angles of the motorcycle and transmits them to the dashboard Below are overviews of the dashboard unit and the sensor Dashboard LED blinks on when battery is charging a SPEEDANGLE Menu Button press to enter menu or in a menu to go to the next item Select Button press to start stop recording or in a menu to execute the function or adjust the value USB Port External GPS Antenna Connector Backlight Switch Power Switc Sensor Connection Cable Bracket The holes marked at the ends of the red lines co
15. Menu Press SELECT to set the Finish Line at 60M or 100M long Press SELECT to designate what is to be used as Main Display between Lap Time and Session Time Press SELECT to designate what is to be used as Sub Display among Best Lap with time gap time gap displayed after a lap is complete Last Lap and Sec tor Time if there are Sector Lines available Press SELECT to choose a time length the Main Dis play and Sub Display are to be held when a record is updated You can select a value among 10 20 30 and 90 Press SELECT to go to Drive Mode The system will ask you SURE Press SELECT to confirm Other wise press MENU to cancel Press SELECT to exit Laptimer Menu and go back to Timer Using GMOS 26 Connecting GMOS to a Computer Before connectinig GMOS to a computer for the first time please go to www speed angle com download and 1 go to the SpeedAngle R4 section to download the latest version of SpeedAngle R4 zip and then 2 go to the USB Driver section to download FTDI USB driver E MA Product Show Room Download Shop Dealers News Customer Service Manual SpeedAngle R4 KML Converter USB Driver SpeedAngle R4 is a simple yet powerful tool to analyze your ride With G force color cod the trace and its unique graphs of speeds lean angles and longitudinal G s it provides clues to help relive your riding motions find your riding style and improve your cornering Hold your mouse key and dr
16. OP a SACUIT WEST 90 seconds later Oku i SET NEW SACUIT WEST TIMER STARTS AT 90KMH If there are more than one Track found GMOS will list them and wait 90 seconds so that you have time to select one Press MENU to go to the Track you want and then press SELECT to confirm Then GMOS will enter Standby Mode SEARCH RESULT SACUIT EAST SACUIT WEST 08_25_12 14 38 SET NEW When more than one Track is listed and none of them is selected in 90 seconds as GMOS will not be able to know which one to use it will automatically prepare to set a new Track or overwrite Track 15 if no empty Track is available SEARCH RESULT SACUIT EAST SACUIT WEST SACUIT WEST 08_25_12 14 38 W SET NE TIMER STARTS AT 90KMH Using GMOS 19 In either case if you do not want to use the Track s GMOS found but would like to set a new Track instead please press MENU to go to SET NEW and then press SELECT to confirm Then GMOS will enter Standby Mode Til vz 12 30 SEARCH RESULT SACUIT EAST SACUIT WEST 08 25 12 14 38 vill MENU SET NEW za 12 30 SEARCH RESULT SACUIT EAST SACUIT WEST 08_25_12 14 38 SET NEW 12 TIMER STARTS AT 90KMH OVERWRITE 09_08_12 09 26 TIMER STARTS AT 90KMH Selecting A Track Manually To Use Or To Overwrite You can ignore the search result and select a Track manually to use or to overwrite Press MENU to enter Laptimer Menu when GMOS is GPS positioning
17. a table of the Drive mode features aeons MG 28 43 45 OG O 9 icons and Their Functions 1 GPS Antenna Icon indicates the quality of GPS signal reception The more vertical lines the icon displays the better the reception and thus the higher the positioning accuracy e If there are less than 4 satellites locked the GPS Antenna Icon will not be displayed This will not interrupt ongoing log recording However if this hap pens when you are pressing SELECT to start a new log the system will not start recording Instead a POSITIONING message will appear for about 2 seconds in the Message Area The GPS Antenna Icon will reappear when the positioning process is completed Then you can press SELECT again to start recording a new log 2 REC Icon flashes when GMOS is recording The icon will flash faster when there is about 50 minutes of memory left at double soeed when there is about 10 min utes left and stays visible when the memory is full Using GMOS 12 e The max log time is 7 hours or 254 logs e fthe REC Icon does not appear after you press SELECT to start recording this means the system can not record logs A message will be displayed in the Message Area indicating the reason the GPS module is still position ing the memory is full or the number of logs has reached 254 Please refer to 10 Message Area p 14 for more information e Entering System Menu will not interrupt recording unless you
18. ag to define an area to create an Area Report R4 has integr the original Track Manager software with it So you can managed track settings with R4 can even edit a track setting directly on the trace Please download SpeedAngle R4 and unzip first Double click on the icon to launch it Na installation procedure is required Download SpeedAngle R4 01 4 Oct 01 2014 Then follow the steps below Product ShowRoom Download Shop Dealers News Customer Servi Manual SpeedAngle R4 KML Converter USB Driver 2 a FTDI USB Driver for Windows setup executable After download double click on the file to start installation FTDI USB Driver for Mac OS X 1 Unzip R4 Double click on the USB driver to start installation 2 Connect the dashboard unit and your computer with the sup plied USB cable Power on your GMOS dashboard unit GMOS USB CONNECTED AFTER USE TURN THE will enter USB mode automatically and display USB CON m oFr to CHARGE NECTED on the device screen 3 If this is your first time connecting to this computer your Win dows will search for the driver and install it automatically Wait till it shows Your Device Is Ready to Use Sometimes this may take up to a few minutes Installing device driver software FF 11 41 2014 10 1 gt di cet Paz m Your device is ready to use EG TF 1144 i Se We ia Enp OSARR 2014 10 1 Using GMOS 27 4 Double click on the SpeedAngl
19. ain frame near the foot peg Main Frame Avoid places that may move swing wag turn or vibrate too much such as handle bar bike tail and fairing etc Handle Bar Tail Exhaust Pipe Fairing Suspension Installing GMOS 7 3 Clean the mounting surface with alcohol and let dry Make sure the UP lettering is pointing upward and FRONT to the front With the supplied red sponge tape adhere the sensor to the installation location Please also make sure the sensor cable is secured 4 Consider changing the installation location if you see the lean angle meter needle moving erratically during a turn in Drive Mode or you see such lean angle graph pattern as the figure to the right in the analysis software SpeedAngle R4 The bike is leaning into a turn but the angle degree measured is near 0 too much vibration These peak like lean angle patterns are also a result of too much vibration If your angle shows a similar pattern in R4 as below the sensor is installed in a wrong direction Make sure the FRONT on the sensor case is pointed to the front of the bike Installing GMOS 8 Installation Checklist After installation please use this checklist to help ensure the installation is correct o Is the sensor installed to a location that will not move swing wag or turn o Is the sensor installed to a location with least vibration o Is the sensor parallel to the longitudinal center
20. all the bracket first You can either use the supplied 3M Dual Lock tape and adhere the bracket to a place you like or buy an AMPS hole pattern mount from the market and bolt the bracket to the mount To use the 3M Dual Lock Tape clean the mounting surface Bicker back and the back of the bracket with alcohol and wipe dry Keep the SA logo rightside up Apply the joined pieces to the back of the bracket and press the bracket to the mounting surface Let sit for at least 24 hours after the application to obtain the best bonding strength Installing GMOS 5 If you are using an AMPS hole pattern mount please find the diagonal holes on the bracket and fit them with the corresponding holes on the mount plate Then bolt them together If you would like to make your own mount plate no problem The hole pattern on the bracket is designed to form as many equilateral triangles and squares as possible to allow you the maximum freedom when adjusting fitting orientations Below are two examples After the bracket is installed insert the left end of the device into the bracket then click the right end into place Installing GMOS 6 Installing Sensor Installation Step by Step 1 Find a plane on either side of the bike body that is parallel to the bike body longi tudinal center line and vertical to the ground Top View Rear View Parallel to the bike body center line Vertical to the ground 2 The best location is on the m
21. ard rrurrrunenunenannrannnnnnnannnennnannnernnsennsennn 9 Installing External GPS Antenna orrranennnrnnnnranennnnrnnnranennnnnannnnannannnaannsennsnnnn 9 USING GMOS vredens ENEAN EA ERNETEN 11 TANN Le 11 Getting Started EEE 11 Drive Mode EEE 12 Icons and Their Functions He 12 GPS Antenna ICON ane 12 REG NGO EEE 12 Temperature Alert arrarranrnnrnnrnnrnanvanvnnnnnrnannannnnnnnrnnnnnnnannannnsnnsenn 13 PV 13 EET srecacasccasesnsrssen pare E E E 13 G force Bar rrerannnnenannnrnannnernannnnrnanenuenanenunnnnnnuennannernnnnneennneneennne 13 Lean Angle History cccccccecceccceeceeccescaeeceesaeeceeeuseseeseueseesaeeses 14 Max FOT LER ANGIO ae 14 Lean Angle Meter cccccccceccsccceeceeeceeceseceesueeseesueeseeseuesensaeenes 14 Message Area rrnnrrnnnnnnvnnnnnnnnnrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnene 14 TOP PEN dn 15 UNS Nr 15 Current Lean Angle sc cicscecctyndoxucdeeeaseceuenderenseaoseqnuersneee caireessesuaanacden 15 System Menu rrannnurnnnnnurnnnenunnanenusnnannunnnnnnernnnenernnnennennnenuenunnnernnnnneennne 15 reeEehvvvvrv4vrvrvvrvr er snes 17 NON rreran A E EE A E 17 Knowing the Buttons ad 18 GPS POSTING nd 18 PUO SN sen a a anon mee macenapsucuaensa E E E E 18 ENO Track Is FOUNO ve 18 If There Are Tracks Found ccccccecceeeceeeeeteeeeeeteeeeeceeeeeeteeseeeteeteeees 19 Selecting A Track Manually To Use Or To Overwrite rrrrrrarrrarn
22. e Auto Search will be executed only once after GPS positioning is complete To run Auto Search again please reboot GMOS and enter Timer Mode again If No Track Is Found If this is the first time you are on a track and you do not have any setting preloaded there will be no Track found GMOS will prompt NO TRACK FOUND on the screen and wait for 90 seconds so that you can view it before it enters Standby Mode You Using GMOS 18 can skip the wait by pressing any of the keys GMOS will prompt SET NEW and a Track number meaning it will set a new Finish Line later and save it in that Track If there is no empty Track available GMOS will prompt OVERWRITE and the name of the Track it is going to overwrite Track 15 by default instead Till Zz 12 30 TOP as or SET NEW 01 NO TRACK FOUND PRESS ANY KEY TO SET A NEW TRACK TIMER STARTS AT 90KMH Till za 12 30 TOP a op OVERWRITE 09_08_12 09 26 TIMER STARTS AT 90KMH If There Are Tracks Found If you have had Track s set up or preloaded whose reference point is within 3KM of your location you will see them listed as the search result If there is only one Track found GMOS will list it and wait 90 seconds so that you can view the result You can skip the wait by pressing SELECT to confirm Then GMOS will enter Standby Mode preparing to use this Track to produce lap times Til TZA 12 30 Yil vz 12 30 SEARCH RESULT T
23. e R4 icon to launch it 5 Click on the MENU button at the bottom left go to Tools and select Log Downloader V ID Track W Date W Time V Custom Field VI From 1 Duration Track Change User Erase All Name Memory For more information such as preloading track settings or modifying Finish Line location after a log has been recorded please watch the tutorial videos on www SpeedAngle com Download SpeedAngle R4 section GMOS utilizes high speed download to save download time If you are downloading with a laptop and are encountering download errors please set the battery management plan to HIGH PERFORMANCE Using GMOS 28 ES TROUBLE SHOOTING Q Why did the No SENSOR message appear even though my sensor was connected Please check if the sensor cable and the device cable are porperly and securely connected Make sure that the arrows on the cable heads align with each other and then insert the plug into the receptacle until you hear a click Also the connection must be made before the power is switched on otherwise the sensor will not be recognized by the device Q How come the lean angle meter needle was not moving during the ride Please make sure the sensor is connected Check to see if the UP lettering is pointing upward and FRONT to the front of the bike It must be parallel to the longitudinal center line of the motorcycle body and vertical to the gro
24. e lines in the GPS Antenna Icon are shown Also make sure that your dashboard or external antenna is installed away from the fuel tank area with a clear view of the sky If you would like to change the width after a Line has been set please go to Track manager to configure the setting Another reason might be that the track orientation was set in reverse As a result the Finish Line crossing was viewed as invalid by GMOS To change the orientation please go to Track Manager to configure the setting Troubleshooting 30 The third reason might be that a wrong Track was selected As the Finish Line location was not within the track area hence the Line was never crossed Why did the latest record list the record of my sessioin before last instead of my latest session The record will not be overwritten until you cross the Finish Line and produce a lap time in a new session If you did not cross the Finish Line in the new session there was no new lap and thus no new record Why was the USB CONNECTED message not prompted when my GMOS was connected to my PC Please make sure you use the supplied USB cable 5 pin male mini USB and that the USB cable is connected to the USB ports of the computer and the dash board unit securely Also make sure the power Is on I cleared the logs by accident Can I retrieve them We are sorry but once the logs are cleared they can not be retrieved Please remember to download the logs to yo
25. em SYSTEM JAN 01 11 12LOGS 85 MEM LEFT SYSTEM MENU RESET MAX ANGLE 37 42 Press SELECT to clear the record RESET TOP SPEED 108 Press SELECT to clear the record ANGLE THRESHOLD Press SELECT to set the threshold at 10 20 30 or to turn it off GMOS will ignore the angles measured when your speed is below the threshold This is to filter out the angles when you are adjusting your position or moving the bike around TIMEZONE GMT Press SELECT to set your local time zone offset from GMT at a number between 12 and 12 UNIT MPH KMH Press SELECT to set the speed unit as MPH or KMH CLEAR MEMORY Press SELECT to clear the memory A SURE mes sage will be prompted Press SELECT again to con firm or press MENU to cancel Once the memory is cleared the number of logs dis played at the top of the menu will be down to 0 and the memory left be back to 100 LCD BRIGHTNESS Press SELECT to change the LCD brightness GO TO TIMER MODE Press SELECT to enter Lap Timer Mode A SURE message will be prompted Press SELECT again to confirm or press MENU to cancel Please note that if you enter Timer Mode while GMOS is recording data the logging will be terminated automatically SAVE SETTINGS AND Exit Press SELECT to save the settings and exit Menu Using GMOS 16 Timer Mode Introduction To enter Lap Timer Mode from Drive mode please enter System Menu press MENU to go to GO TO LAPTIMER MODE and press SEL
26. email custserv speedangle com with your registration number The registration number can be found at the back of your GMOS dashboard unit or on the Welcome Screen Introduction and Functions GMOS JI100S is a state of the art data logger developed for motorcycle enthusi GMOS Overview 1 asts It is capable of recording not only your track performance but also the motion and trace of your ride Equipped with cutting edge 10Hz GPS module and aero technology plus our processing algorithm optimized for motorcycles GMOS JI100 series features Motion and Trace e Real time lean angle up to 69 degrees e Max degree of left right lean angles e Max angles of the last three turns e Real time longitudinal G of acceleration deceleration up to 1 5G e Real time GPS speed up to 255 MPH 410 KMH e Top GPS speed e 10Hz GPS trace mapping e PC analysis Lap Timer e 1 1000 second lap time resolution e Lap time e Best lap time highlighted with time gap e Last lap e Lap length e Session time e Sector time e Auto Track search e Auto Finish Line setup e Auto Timer start e Auto Timer stop e Auto data logging e Auto Lap Record Display e Up to 7 Sector Lines in one Track uploaded via software e Up to 15 Tracks e Track editable via software e Lap time record report with motion data All the data can be recorded in the built in memory for up to 7 hours or 254 logs whichever is reached first After your ride connect the G
27. et the idle time at 0 e To keep the data logging running while your are waiting on the grid after a warmup lap set it at 180 To set the idle time please press MENU to enter Laptimer Menu Using GMOS 21 Or you can press any of the keys to stop the Timer and data logging manually If you press MENU GMOS will stop the timer AND enter Laptimer Menu Viewing Your Lap Time Report Once the Timer stops a summary of your latest session will be automatically displayed listing its date time track setting dura tion best and average lap time top speed and average speed To see the time top speed and average speed of each lap press SELECT to enter DETAIL To exit DETAIL either press MENU to go to EXIT and press SELECT to confirm or do nothing Once you reach the starting speed again GMOS will automati cally exit and start the Timer e f there were less than 3 full laps created in a session there will not be a summary available You will see the screen to the right instead e The reports of up to the previous 14 logs can be viewed in the LapTimer Menu vz 1123 1912 LOSAIL 28 09 9 BEST 1007 2 23 502 AVERAGE 2 44 750 171 TZA 2 30 3 08 311 123 82 2 56 972 156 107 2 33 933 164 124 2 34 107 162 124 2 34 859 161 124 2 33 311 165 125 2 32 502 166 125 ZA 1124 2028 LOSAIL 2 43 0 NOT ENOUGH DATA FOR BEST LAP AND AVERAGE LAP Advanced Setting a Better Finish Line with Auto Set How A Finish Line Is
28. here the GPS antenna to a location with a clear view of the sky To avoid signal loss the cable run must not be kinked or crushed or have a bend diameter less than 2 inch 5 cm The cable should be laid as straight as possible If too tight Examples of damaged antenna cable Then insert the antenna cable plug to the jack on the dashboard WARNING For your safety please check and make sure the device sensor antenna and cables are all properly secured Installing GMOS 10 USING GMOS Charging GMOS For safety purposes the battery that comes with your GMOS has just enough charge to sustain a working voltage Please charge the battery before starting using your GMOS To charge the battery please use the supplied USB cable to connect your GMOS with a computer an external battery pack charger or an AC USB converter plug and then insert the plug to a wall outlet Once the charging starts you will see a red light blink on on the top right corner Please make sure both the power and the backlight are off during charging other wise the battery will never be full The red light will go off once the the charging is complete Normally this will take about 2 5 hours If you are going to put GMOS away for a couple of months or more DO NOT store it on an empty battery Keep it in an environment near 20 C 68 F Otherwise the battery life might be reduced severely Getting Started When GMOS is powered on you
29. line of the bike and vertical to the ground when the bike is upright o Is the UP lettering pointing upward and FRONT to the front of the bike Connecting Sensor to Dashboard When connecting the sensor to the dashboard unit make sure the arrows on the cable heads align with each other Insert the plug into the receptacle until you hear a click Connect the sensor before you turn the device power on NOTE If the sensor is connected AFTER the power is on it will not be recognized by the device You can choose not to connect the sensor and use the dash board alone as a simple lap timer In this case no lean angle data will be collected As a reminder a NO SENSOR message will appear where the G force bar is If later you would like to reconnect the sensor remember to turn the power off before the connection Installing External GPS Antenna GMOS JI100S comes with a built in GPS antenna so the external antenna is not required to be installed However if the trace on the analysis software map looks er ratic or is dispersed severely in some places the built in antenna is being inteferred In this case install the external antenna and place it away from the engine area If you are already using an external antenna check if it is damaged see the next para graph Installing GMOS 9 Errattic trace Installing the external antenna to the tail To install please use the supplied Dual Lock tape to ad
30. n the latter case the system will continue to function except that the recording will stop Please download your logs and then clear the memory to release the memory space LOGS FULL displayed when SELECT is pressed to start recording but the number of logs recorded has reached 254 which Sku is the maximum number of logs the system can record Please download your logs and then clear the memory to release the memory space 11 Top Speed shows the top speed measured since GMOS is powered on e To clear the record go to System Menu and select RESET TOP SPEED 12 Current Speed shows the current GPS speed up to 255 MPH 410 KMH e To switch the measuring system from MPH to KMH or vice versa please go to System Menu and select UNIT MPH KMH 13 Current Lean Angle shows real time lean angle degree reading up to 69 System Menu In System Menu you can e clear the maximum lean angles recorded since GMOS is powered on e clear the top speed recorded since GMOS is powered on e set the speed threshold below which lean angles are to be ignored e set the built in GPS clock to your local Time Zone e change the measuring system Using GMOS 15 e clear the logs in the memory and e enter Lap Timer Mode To enter System Menu press MENU while you are in Drive mode As a rule in system Menu pressing SELECT will execute the function or adjust the value of the menu item Pressing MENU will go to the next it
31. nd cover the width of the track lane Finish Line Adjust Line Width If Necessary If necessary before setting the Track adjust Line Width according the size of the course and the quality of GPS reception The width is 100M by default However if your track is small and very winding such as a go kart course adjust the width to 60M To adjust the width please enter Laptimer Menu e In some very small circuits you may even need to set the reference point outside the track lane to make sure the Line does not extend to the next neighboring lane and cause unwanted crossings This can done with SpeedAngle R4 Track Manager set the reference point outside the track so that the line does not extend to a wrong lane e To adjust Line Width after a line has been set please use SpeedAngle R4 Track Manager For more information please see the tutorial video on www speed angle com download SpeedAngle R4 section Using GMOS 23 Linear Track The way to set the Finish Line for a linear track is just a little bit different from setting for a closed track The easiest way Is to use Track Manager to set and upload your Finish Line Otherwise ride to your Finish Line location set the starting speed at 10 recommended and follow the steps below e Turn GMOS on Ignore any Tracks found and select SET NEW e Speed up to your starting speed to set the Finish Line e Once you see the Timer running the Finish Line is set e
32. nform to AMPS hole pattern diagonally Other holes form squares and equilateral triangles This makes it easy to adjust fitting angles if you are making your own mount The left claws are taller than the right claws to fit the dashboard profile Please make sure the orientation is correct before clicking the dashboard into place GMOS Overview 3 Sensor Sensor The sensor must be installed parallel to the bike body vertical to the ground with UP pointing upward and FRONT toward the front of the bike Sensor Connection Cable GMOS Overview 4 WARNING DO NOT connect the dashboard and or sensor with any device other than com puters Otherwise they might be harmed E M INSTALLING GMOS The installation of the GMOS dashboard unit and sensor unit is easy No drilling or wiring is required After the installation please remember to align the sensor as instructed and then you are ready to go Installing Dashboard Unit Location If you are not using the external GPS antenna for best GPS reception quality please install the dashboard at the front beyond the steering stem area and keep it clearly visible to the sky If you have the external GPS antenna attached you can place it at a place you like However in either case please avoid places near the engine such as the fuel tank top Without External Antenna With External Antenna Installation To install the dashboard please inst
33. nnenenn 20 Starting Timer and Data Logging rrrnrrnnnrrnarnnnrrnervanennnrnanenanennnnnaennen 21 Stopping Timer and Data Logging save 21 Viewing Your Lap Time Report rrrurnnrnannnnnnarnnrnannnnnnnnnernernarnnennannnenenn 22 Advanced Setting a Better Finish Line with Auto Set rrrrrnrrrarenrennre 22 How A Finish Line Is Set with Auto Set r rrrrrrarrnnrrarnnernnnnnnrnnnn 22 How to Control Your Finish Line Location rurrarennrnannnrnnnnnennnnnn 22 Stay Close to the Center Line rrrranrnnnrnannnnnnnnnnnernnnnnnnrnnnrnnnnnnn 23 Adjust Line Width If Necessary rrrrrrnnrnnrernnrnanennnnrnnnnanennnnnnnnneen 23 Ga EEE EE enacted 24 Connguring the ME rn 24 Connecting GMOS to a Computer rrrnnrnannnnnnnannnnrnnnnvnnnnnnrnnnrnnnnnnnrnnnnnnnennn 27 TROUBLE SHOOTING siritissatvisietisecitcsceraiseeissiisenseimsaieasieens 29 WARRANIY Favre 32 SPECIFICATION vavsvv4ecqvqvvmm rms 33 fk GMOS OVERVIEW What Is in the Package Thank you for purchasing GMOS JI100S Your box contains the following items 1 Dashboard unit and Bracket 2 Sensor unit 3 External GPS Antenna UP LNOUSs 4 USB Cable 5 GMOS JI100S Quick Manual 6 Hex Key Wrench 7 Adhesive Tapes 8 SpeedAngle Logo Stickers 9 Bolts and Nuts SEE lf any of these items is missing from your box please contact your local dealer lf you purchased your GMOS directly from www speedangle com please
34. nt you might see the reading of the latter larger than the former when the calibration is in effect In such cases the reading of the Angle History and Max Angles should be taken as valid Please note that all the logged data have been calibrated Please also note that in the rare cases where the interaction is too severe to be com pensated by the calibration mechanism the calibrated lean angle measurement might still be exaggerated sometimes to as high as 69 degrees or be discarded as invalid by the GMOS Filter CONTENTS GMOS OVERVIEW sussaievisecsneisceseonsersenierisenrssensieniiesinheneers 1 What Is in the Package needs 1 Introduction and Functions sccsanicsracetnacedianatssesxatdasntaenssandiueentsrisardiosatonkaineenentens 1 Moton and aCe vrede 2 EaP TINO Sarearen E any AE EAA PE EE AA EEN EES 2 GMOS at a Glance EEE NE 3 Dashboard cpinacecaecescpieigeeusqancsaceataaeseieanaeseaiasateteaceoneseniatesnteaveanesacusvatweansees 3 DACKO EEE E sear Sexeanalence 3 SONSON EN ene aseetentoee 4 INSTALLING GMOS pri 5 Installing Dashboard Unit 5 coir erie or reettcey sem sence cenenass pons tiani cue eae veioeasennaseee eden 5 KEN ereina A E 5 WTO aare E E eeosaeurs 5 Installing Sensor rrrranernrennornanennarnanenanennnenanennnnnnsnnunnnasnnaannsennesnneennsenneennsennn T Installation Step by Step ccccesssecssesseeseressessrececcerscescurseeesersesesersseeeas T Installation Checklist EE 9 Connecting Sensor to Dashbo
35. und Q The lean angle measured was smaller or larger than the actual angle Please check to see if the sensor is installed with the correct orientation See above Make sure the installation location does not move turn swing wag or vibrate too much For more information please see the Installing Sensor section Make sure you are using the red sponge tape included in the box to install the sensor Do not use the Dual Lock tape It will create extra vibration Please also make sure that the environmental temperature is within 36 F 140 F 2 C 60 C Using GMOS outside its operating temperature range might affect measurement accuracy Q Why was the lean angle history not updated after finished a turn There are two possibilities The first is that your speed of the turn did not exceed your Angle Threshold As a result the angle was ignored and was not recorded To adjust the Angle Threshold setting please go to System Menu The other is that the vibration when you were leaning was too much As a result the angle was categorized as invalid by GMOS Noise Filter If the vibration was not caused by road shock please check if the sensor was installed securely and if the installation location swings or moves If necessary install the sensor to a location with less vibration Troubleshooting 29 Why did the GPS speed read 0 when I was riding This happens when the GPS signal reception is poor and there are not enough satellites
36. ur PC when you finish the ride Troubleshooting 31 EI WARRANTY Your GMOS comes with a limited one year warranty with your purchase Speed Angle Inc warrants the GMOS device against defects in materials and workmanship under ordinary use for one year from the invoice date This limited warranty does not cover damage due to external cause including but not limited to accident abuse misuse improper installation improper connections with devices or components other than specified and unauthorized repair or alternation To request warranty service please contact your local dealer If you purchased GMOS directly from www speedangle com please email custserv speedangle com In the email please include a problem description and your GMOS registra tion number Your GMOS registration number is a combination of 1 letter followed by 7 digits It can be found at the back of your GMOS dashboard unit and on the Welcome Screen A Return Merchandise Authorization Number RMA and a war ranty service shipping label will be issued if the request is approved The RMA and shipping label are valid for 30 days from their issue date To ship the GMOS device back for warranty service please follow the instructions below e Please ship the GMOS device in its original or equally protective package with a copy of the original packing slip or the PayPal invoice e Please print and cut out the issued shipping label and adhere it to the top of the package
37. will see the Welcome Screen G MOS appear displaying your User ID can be edited via SpeedAngle jJNoos R3 GMOS model and its registration number for 5 seconds SPEEDANGLE RIDER You can press any key to skip the wait RN 1234567 WWW SPEEDANGLE COM Then GMOS will display the Liability Screen reminding you PLEASE CHOOSE SAFETY Tel OVER PERFORMANCE WHEN to choose safety over performance when riding and that you OVER PERFORMANCE WHEN assume full responsibility and risk when using GMOS Then permer ats RISK AND GMOS will enter Drive mode or Timer Mode automatically Re arep to ITS USAGE depending on which Mode you were in when you turned GMOS off last time In Drive mode GMOS displays your speeds lean angles and G s and record these data plus GPS traces In Timer Mode GMOS displays the speeds G s and lap times and records these data plus lean angles and GPS traces Using GMOS 11 Drive Mode Drivie Mode is suitable for open road cruising Start your ride after you enter Drive Mode GMOS will display the riding motion data collected real time including GPS speed top GPS speed acceleration deceleration G real time lean angle max left right lean angle and show the max angle history of the last three turns To record the data press SELECT The envelope shaped REC Icon will start flash ing and a START LOGGING message will be displayed To stop recording press SELECT again Below are a diagram and
Download Pdf Manuals
Related Search
GMOS JI100S User Manual