Digital Scale Operation Manual
Contents
1. SALTER Brecknell SPC SEPies Digital Scale Operation Manual Revision 1 0 August 17 2000 Contents subject to change without notice Salter Brecknell Weighing Products 1000 Armstrong Drive Fairmont MN 56031 Tel 800 637 0529 Tel 507 238 8702 Fax 507 238 8271 E mail sales salterbrecknell com Web www salterbrecknell com A WARNING Use only the AC adapter which comes with the scale Other adapters may cause damage Internal service to this product should be performed by a qualified person only There are no user serviceable parts inside eigen Avoid installing the scale in areas of direct sunlight and high humidity Also avoid drafts vibrations and dusty conditions If the scale is not to be used for a long period of time remove the battery from the battery com partment to avoid leakage which may cause damage to the instrument To extend the life of your digital scale do not drop items to be weighed onto the platform or over load the scale beyond its rated capacity Shock loading and overloading may damage the load cell and void the warranty NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful in terference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy a2. g SPC 65M 65 x 0 1 kg 150 x 0 2 lb SPC 180M 180 x 0 2kg 400 x 0 5 Ib SPC Series Product Matrix Specifications CONSTRUCTION OPERATING TEMPERATURE RANGE Housing ABS 68 F to 77 F Sub Platform Metal 20 C to 25 C Platter Metal Feet Non skid Hard Rubber MAIN POWER SOURCE AC Adapter 9VDC 100 mA DISPLAY included a gmenk ECD ALTERNATIVE POWER SOURCE KEYPAD 9V alkaline battery replaceable 4 key Tactile Keypad WEIGHT OVER CAPACITY ANNUNCIATION Net Weight 9 3 Ib 4 2 kg 103 of Full Scale Capacity Shipping Weight 10 7 Ib 4 9 kg SERIAL PORT Full Duplex RS 232 Female DSUB9 Calibration Your SPC Series scale is ready to use right out of the box There is no need to calibrate the scale unless you feel that the scale has become inaccurate It is a good idea to check the calibration of your scale from time to time with a precision test weight Transcell recommends that you perform a new calibration on your digital scale at least once a year The SPC must be calibrated with the precision test weight specified in the table below To calibrate the scale 1 Remove all items from the platter and turn the scale OFF Press and hold the Ib kg key while turning the scale back ON When the scale shows CALO you may release the Ib kg key 3 Press the ZERO key followed by the Ib kg key The scale then displays CAL1 followed by the necessary calibration test weight 4 Place the appropriate
3. nd if not installed and used in accordance with the instructions manual may cause harmful interference to radio communications Operation of this equipment in a resi dential area is likely to cause harmful interference in which case the user will be required to correct the in terference at his her own expense Getting Started om Plug the AC Adapter into the scale first then into an AC outlet For portable operation install one 9V alkaline battery not included in the battery compartment located underneath the scale base Place the scale on a stable and firm table or floor If you are using the scale with UPS Online software a Connect the optional NMC 1 interface cable between the scale and your PC b Configure the UPS Online software for a Fairbanks 70 2453 4 scale c Configure the UPS Online software for the following communication parameters 9600 Baud 7 Data Bits Odd Parity and 1 Stop Bit Press the ON key All segments will briefly appear followed by the version code and finally an indication of zero weight The scale is now ready for use Keyboard and Display Diagram Transcell 7 fi a Technology ZH 30n1 108 CAPACITY 150 Ib x 0 2 Ib 65 kg x 0 1kg Je De Operation How to obtain the weight of an item 1 on Before weighing an item make sure the scale shows a zero weight indication If it does not
4. remove all items from the platter and press the ZERO key Place the item on the center of the scale s platter and allow the weight indication to stabilize Select the desired unit of measure by pressing the Ib kg key Operation Continued How to enable or disable the automatic turn off function When the automatic turn off function is enabled the scale will automatically shut itself off to pre serve battery life after two minutes of inactivity NOTE When the scale is shipped from the fac tory the automatic turn off feature is disabled 1 Turn the scale OFF 2 Press and hold the ZERO key while turning the scale back ON The scale displays the new status of the automatic turn off function A ON means that the auto turn off function is now enabled A OF means that the auto turn off function is now disabled 3 Repeat step 1 until the automatic turn off feature is enabled or disabled as required Message Explanation 0000 Indicates that the weighing capacity of the scale has been exceeded bAtt Indicates that the batteries need to be replaced Err 2 The scale s calibration information has been lost Re calibrate scale Indicates that the negative number is beyond the display s capability 99 9 Possible Scale Operation Error Messages MODEL CAPACITY GRADUATION SPC 150 150 x 0 2 Ib 65 x 0 1 kg SPC 400 400 x 0 5 Ib 180 x 0 2 k
5. test weight on the platter and wait three seconds 5 Press the Ib kg key to save the test weight calibration value 6 Once the test weight calibration value has been saved the scale shows an End message 7 You must now turn the scale OFF and then turn it back ON without pressing any keys Your SPC is now calibrated and ready for use MODEL S CALIBRATION TEST WEIGHT SPC 150 400 50 Pounds SPC 65M 180M 20 Kilograms Test Weight Values
Download Pdf Manuals
Related Search