Home

Christie CP2000-XB User Manual

1. 25 of image Figure 2 13 Example of Alternative Offset Specification Horizontal Position The Horizontal Position of the image can be offset that is shifted left or right of lens center using the Left Right Offset buttons from the Main Lens menu Starting with no offset the 2048 x 1080 image from this projector can be moved by a distance of 410 pixels resulting in up to 70 of the image displayed on one side of lens center Figure 2 14 Note that the positioning shown at right is often mistakenly referenced as 70 offset but it is not it is 40 offset derived as 432 1080 x 100 A 70 offset is explained below and shown in Figure 2 15 40 Offset 30 lens center Max amount of image to one side of lens center 70 approx Figure 2 14 Horizontal Offset Range CP2000 XB User Manual 2 11 020 100163 04 Rev 1 06 2009 Section 2 Installation amp Setup CHix IS TIE Alternative Method of Describing Horizontal Offset Horizontal offset can also be specified as the distance traveled from lens center and expressed as a percentage of half of the image width For example an offset spec of 70 means a centered image can be moved by a distance of 717 pixels resulting in 85 of the image projected to one side of lens center and 15 on the other See Figure 2 15 NOTE Example only Beyond range for this projector 70 Offset l j i i i l i i i a g
2. 1 85 image err Figure 4 4 Top Masking for Scope CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE Alternatively masks may be installed at each side of the screen in ae ee oe I screens order to change the width of the screen but not its height naan ae ai Migi masking to hide screen edges e Add masks for flat e Open masks for scope _ 1 85 image gt In some cases a theatre has both side and top bottom masking installed This arrangement is the most flexible of all Refer to Figure 4 6 for a summary of the basic factors affecting cinema displays in a variety of theatres E Masking moved aside Figure 4 5 Side Masking for Flat Theatre Type All the Pixels All the Time Quickest Scope gt Flat 3 eo Horizontal O t ig 2 39 screens Compression 1700 across RO gt lt we Horizontal ey Compression 2048 across TOP MASKING THEATRE 1 85 screens Flat Flat 3 S v Re size electronically with TPC Masking source amp screen settings NOTE Example shows vertical offset EXTRA ll THROW ai aie 1280 gt 1700 approx FIXED SIDE MASKING arom FIXED SIDE MASKING namon B Compresse oom 1700 across approx 1200 gt ia E troo Top and or bottom masks present Figure
3. CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation Adding a New Lamp mam eorn SAVE required Main Status Custom Advanced Admin About eee ae Select new lamp New Lamp added to top of type from drop list down list Lamp Type cxL 45 e Lamp timer will Enter serial reset to 0 hours number for new Serial FFFF0702 Hours lo Enter the number lamp installed of hours logged Change Reason Lamp Type Change on the newly Date Tine Type Serial Number Hours a installed lamp 2008 10 13 14 20 CxL 60 vgkjisog toa B 2008 09 11 04 56 C L 60 MA 37 2008 08 26 09 26 CDRL 6050 testO0l lz on Preference Lamp Lamp History Test Pattern User Description of why lamp change required Read only window that displays the information of recorded lamps 11 13 48 9 Figure 3 18 New Lamp Fields Table 3 11 New Lamp Fields NEW LAMP FIELDS Lamp Type Select lamp type using the drop down list Touch to activate keyboard for editing Change Reason Select description that best explains why lamp was changed Save Touch to record the new serial number and date and automatically reset the lamp timer to the same value entered in Hours text box Hours Enter the number of hours logged on the newly installed lamp If the lamp has never been used the value should be 0 Advanced Lamp History Menu
4. To Temporarily Alter the Active Channel ILS Settings 1 De select the Auto ILS checkbox 2 Adjust the Focus Horizontal X and Vertical Y Offset and Zoom NOTE This does not over write the system settings for the ILS To revert back to the ILS settings check Auto ILS CP2000 XB User Manual 3 11 020 100163 04 Rev 1 06 2009 Section 3 Operation CHix IS TIE l 3 5 2 TPC Status Menu NOTE The Status System menu described here is available to all users For information about the password protected Status Server Status Diag and Status Interrogator menus refer to Section 3 11 Working with Servers and Diagnostics Sample views of the Status System menu are shown in Figure 3 5 Navigate the Status menu as you would Windows Explorer or File Manager expanding or compressing directories as desired by pressing the corresponding small square buttons To see more of the Status menu drag the scroll bar up or down This menu updates approximately every 30 seconds i Information Indicators As shown in Figure 3 5 this blue symbol identifies basic informative data describing the source connection as well as certain non critical historical operational facts about the projector and lamp Such data does not trigger warnings or error conditions Q Environment Diagnostic Indicators The small colored indicators or virtual LEDs for environmental and diagnostic information are green during normal operation These indicators can cha
5. CHRISTIE 6 Maintenance This section describes how to safely maintain the projector NOTE The illustrations provided are to enhance the understanding of the written material They are graphical representations only and may not represent your exact projector model e 6 1 Warnings and Guidelines e 6 2 Maintaining Proper Cooling 6 3 Maintenance and Cleaning e 6 4 Replacing the Lamp and Filter e 6 5 Replacing a Lens CP2000 XB User Manual 6 1 020 100163 04 Rev 1 06 2009 Section 6 Maintenance CH IS TIE l 6 1 6 1 1 6 1 2 6 2 Warnings and Guidelines This projector is designed for safe and reliable operation However safe operation is not assured by design alone installers service technicians trained operators and all other users must maintain a safe environment at all times Please read through and understand all warnings and precautions before attempting to operate the projector Labels and Markings Observe and follow any warnings and instructions marked on the projector The exclamation point within the equilateral triangle indicates related operating maintenance instructions in the documentation accompanying the projector The lightening flash and arrowhead symbol within the equilateral triangle indicates non insulated dangerous voltage within the projector s enclosure that may be sufficient magnitude to constitute a risk of electric shock General Precautions Be aware of the following general
6. Motion Artifacts If the image seems to jump back and forth during horizontal pans the L R Frame Dominance is likely backwards Try reversing the current setting Single 3D Input Does Not Work A single source signal containing both left and right data is not currently supported CP2000 XB User Manual 3 69 020 100163 04 Rev 1 06 2009 Section 3 Operation CHA IS TIE l 3 11 Working with Servers and Diagnostics NOTE Password protected Installers and service technicians only A service login provides two additional Status menus Server Diag and Interrogator for testing certain server functions and communications or for advanced projector diagnostics Status Server Menu The Status Server menu provides controls for testing or confirming subtitling and or metadata commands supplied with presentation content from the site s controlling cinema server The relevant xml files one for subtitling one for metadata can be searched and examined for errors in content or in transmission from the server Reported errors can then help point to potential problems with the server the xml file or the communication link to the projector Note that controls in the Server menu do not activate or turn off metadata or subtitling Controls are diagnostic tools only TEST SUBTITLING FILE xml Enable the Subtitling button to test an xml file supplied with content for control of performance parameters such as synchronization with conten
7. 8 Processor Board Serial 9 Processor Board Type 10 Interface Board Type 11 Formatter Interface Type 12 Formatter Board Type 13 TPC Type 14 ILS Board Serial Number CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 B 19 Appendix B ASCII Messages B 20 P1 IfP1 1 System Status IfP1 2 Signal Information IfP1 3 Operation Status 0 Power Status 0 0ff 1 On 2 LiteLOC 0 Off 1 On 3 Lamp Expiry 4 Lamp Hours 5 Total Lamp Hours 7 Projector Hours 8 Shutter O Off 1 On 20 Lamp Current 21 Lamp Voltage 22 Lamp Power 23 Approximate foot lamberts 0 Signal Status O OK 2 invalid 1 Channel 2 Vertical Frequency 3 Test Pattern O Off gt 0 On 2 Lamp Error 10 Card cage temperature 11 Blue DMD temperature 12 Red DMD temperature 13 Integrator temperature 14 Prism temperature 15 SSM temperature 16 ILS temperature 20 Lamp vane switch interlock 21 Extractor vane switch interlock 22 Lamp door interlock 23 Auxiliary interlock High current 24 Tamper switch 30 Intake fan 1 rear speed 31 Intake fan 2 front speed 32 Card cage fan speed 33 LAD fan speed 40 SmpteA TotalErr 41 SmpteARecentErr 42 SmpteBTotalErr 43 SmpteBRecentErr 50 SecurityInstalled 51 SecurityArmed 52 SecurityTamper 53 CompLidOpen 54 NonCompLidOpen 55 CommFailure 56 BatteryLow CHRISTIE Go
8. These two settings tell the rest of your 3D system that incoming 3D stereo sync informa tion is included with the two L R image data inputs rather than routed separately to the GPIO port e For future single input 3D sources where the server supplies a separate 3D stereo sync to the projector s GPIO port instead set Input GPI according to which input is used 1 e according to your GPIO cable wiring DEFINE L R DOMINANCE Step 5 LIR Input Reference Active Port A B LIR Input GPI hone Display GPT hone Input Frame Dominance fLeft inilarz el Output GPO aro 1 LIR Display Reference Mot Used Dark Time Adj lo Us LIR Output Polarity Output Delay T lo us Inverted Output Delay iF bo deg Page 1 Page 2 aD control O 15 20 04 Figure 3 57 Setup for 3D Choose the leading frame left or right Correct order depends on the cameras used during filming and is needed to ensure smooth motions An incorrect setting creates motion artifacts DEFINE SYNC DISPLAY LOCATION e Set L R Display Reference to Not Used e Set Display GPI to None CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation 6 DEFINE SYNC OUTPUT Set L R Output Polarity to Inverted NOTE f the display appears inverted i e background appears close and foreground appears at a distance you will need to make sure that the cable connecting server output A is connected to projection inpu
9. 001 System Errors and 002 System Warnings System Error and System Warning error messages include two additional parameters P3 and P4 which further describe the error P3 indicates what component or system is involved such as interlocks fans temperature SSM communication or a lamp failure and P4 relays the specific condition detected at the suspect component such an over temperature reading or a slow fan speed reading note these values indicate temperature or fan speed only Refer to Table B 3 Table B 4 and Table B 5 below When a system error is resolved and is no longer present another message reports this by replacing the first digit in the original P3 error code with a 1 CP2000 XB User Manual B 15 020 100163 04 Rev 1 06 2009 Appendix B ASCII Messages CH IS TIE l Table B 3 P3 Codes for 001 System Error Messages Component Code P3 Component Lamp Ignition Failed on 2 Strike Examples of Critical System Error 001 Messages 65535 01002 ERR 001 System Error 0008 00001 Fan Intake 1 65535 01002 ERR 001 System Error 000A 00001 Fan Card Cage 65535 01002 ERR 001 System Error 0021 00001 Lamp Failed to Ignite B 16 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix B ASCII Messages Table B 4 P3 Codes for 002 System Warning Error Messages Component Code P3 Component NOTE System Warning messages can elevate to System Error
10. 4 4 4 packed 12 bits color Cinema dual link A and B 0x00 4 2 2 packed 10 bits color with O E pixels default 0x01 4 2 2 packed 10 bits color with O E lines 0x02 4 2 2 packed 12 bits color with O E lines 0x03 4 2 2 packed 12 bits color with O E pixels 0x04 4 4 4 unpacked 10 bits 0x05 4 4 4 packed 10 bits color mixed 0x06 4 4 4 packed 10 bits color O E pixels 0x07 4 4 4 packed 12 bits DVI port 0x00 Unpacked 8 bits color default 0x01 Packed 10 bits color 0x02 Packed 12 bits color 0 Minimum logging of activities i e for errors only 1 Standard logging errors plus select operations 2 All activities are logged Error Message Enable EME EME 1 EME 001 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 Enable error messages sent via Ethernet where 0 disabled and 1 enabled Refer to ERR B 3 Appendix B ASCII Messages CH IS TIE l Function Code Examples Description and Parameters Error Messages ERR ERR 010 Generated for projector errors Provides error code error type and text explanation 01 Interlock Lamp Fan Error 02 Interlock Extractor Open 03 Interlock Lamp Door Open 04 Interlock Auxiliary Open 05 Card Cage Tamper Interlock 08 Fan Intake 1 09 Fan Intake 2 10 Fan Card Cage 11 Fan LAD 12 Fan Ballast 16 Temperature Prism 17 Temperature Red DMD 18 Temperature Blue DMD 19 Temperature Integr
11. NOTE Manual shut down only Your system may include automation l 2 3 Press the lamp button on the Main menu to turn the lamp OFF You must hold the button down briefly Cool the lamp Warning Wait at least 10 minutes so that fans completely cool the lamp Set the ballast breaker to OFF CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation 3 4 Introduction to the Touch Panel Controller Most users will use the Touch Panel Controller TPC as their main interface with the projector Depending on the installation this Windows based touch sensitive screen is typically mounted on the rear of the projector or at some other convenient nearby location Installers must pre program it appropriately for use at the specific site User Access and Rights Whether or not you can access specific TPC menus and functions depends on how you have logged on to the TPC See Figure 3 2 GENERAL USERS For the general user having no username or password the Touch Panel Controller TPC offers three menus providing e ON OFF toggling of the lamp shutter user test patterns and pre configured displays e Basic status and or diagnostic information about projector components e Versions of software components currently installed Service Installer Admin Advanced General Any User Status Operator Can use New Lamp button Pa i i a Figure 3 2 Map of TPC User Access Rights A simpl
12. Projector Configuration File or Presentation Control File A small file created by the content owner or installer that controls the presentation of the elements and data subdivisions constituting a single version of a title The text component may identify the name of the title 1ts owner its length event points and other attributes The PCF specifies color space target color gamut gamma a k a de gamma aspect ratio and image position settings It does not include screen masking cropping information PCFs were originally intended as part of content distribution PINCUSHION A distortion of the image shape characterized by concave edges PIXEL PICTURE ELEMENT The smallest discernible element of data in a digital image PIXEL CLOCK RATE Pixel clock rate describes the speed at which incoming data is processed and 1s dependant on the native resolution and vertical frequency such as 1280 x 1024 x 60Hz or 2048 x 1080 x 24Hz of the incoming source The two processing paths available in the projector cinema vs non cinema offer different maximum pixel clock rates 110 MHz if cinema path and 165 MHz if non cinema path thus their use with DVI sources depends on the incoming resolution and vertical frequency CP2000 XB User Manual A 9 020 100163 04 Rev 1 06 2009 Appendix A Glossary CH IS TIE l PIXEL PHASE The phase of the pixel sampling clock relative to incoming data PIXEL TRACKING The frequency of the pixel sam
13. References to specific areas of the document appear italicized and underlined When viewed online the text appears in blue indicating a direct link to that section For example Section amp Specifications References to other documents appear italicized and bold such as Christie Service Manual References to software menus and available options appear bold such as Main Menu Preferences User input or messages that appear on screen in status display units or other control modules appear in Courier font Forexample No Signal Present Login christiedigital Error codes LED status appear in bold e g LP Al etc Operational states of modules appear capitalized such as power ON power OFF Signal words such as Warning Caution and Notes are used in this manual to point the reader to specific information or instructions that warn of safety related hazards which may be present and indicates how to avoid them CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE 2 Installation amp Setup This section explains how to install connect and optimize the projector for delivery of superior image quality NOTE The illustrations provided are to enhance the understanding of the written material They are graphical representations only and may not represent your exact projector model e 2 1 Quick Setup e 2 2 Installation Considerations e 2 3 Projector Position and Mounting 2 4 Installing a Lens Lamp and Cooling
14. White Line Code true polarity 5 White Line Code inverted polarity 6 Blue Line Code true polarity 7 Blue Line Code inverted polarity CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix B ASCII Messages P1 P2 4 Input Frame Dominance 0 Left L1 R1 L2 R2 1 Right RI L1 R2 L2 5 L R Input Frame Reference GPI 0 None 1 7 GPII GPI7 6 L R Display Reference 0 None not used 1 Use assigned GPI true polarity 2 Use assigned GPI inverted polarity 7 L R Display Reference GPI 0 None l 7 GPI1 GPI7 8 L R Output Reference Polarity 0 True 1 Inverted 9 L R Output Reference GPO 0 None 1 7 GPO1 GPO7 10 Dark Time 0 4500 us 11 Output Sync Delay 0 200 us CP2000 XB User Manual B 23 020 100163 04 Rev 1 06 2009 CHRISTIE Appendix C System Integration This section explains how to link the projector to serial communication devices and to other external equipment such as devices for 3D synchronizing e C l Serial Links to Projector e C 2 The GPIO Port CP2000 XB User Manual C 1 020 100163 04 Rev 1 06 2009 Appendix C System Integration CH IS TIE C 1 Serial Links to Projector C 1 1 Standard RS 232 Devices From a PC or other controller connect a standard 9 wire RS 232 serial cable CTS RTS to RS 232A port on the Communications and Source Connection Panel located at the rear of the projector Note that a
15. 06 2009 Table of Contents PMMA a DOD ee say uede cartes EE E E aatnive A E EE 3 41 AA PSG aa N U e E E E E E A TA 3 45 Admin General and Admin Lamp Menus cccccccsssssssssseeeeeccccecccceceeeeeeesaaaaaneessseeeeeeeeeeeeeees 3 48 E EE LOS o A E E sane T E A E ess 3 49 3 5 8 Selecting a Display Starting a Presentation i iscssssssssssecesceesdessesesevessevssvsavessevesvessdessouesvouss 3 50 ner Neod orn oree EC OI seri ir ee EAEE eee 3 51 So FETO AA E a E E E E E E E 3 51 3 6 Remote Control of the Touch Panel Controller oo cccssscscceeecceceeeeceeceeecceeeeeeeeeeeseeeeeeeeeeees 3 52 3 0 1 Understanding ASCI Message FOmias eccsccdsssesceceracousessemuennydonteenydevestvasseesaniesaavadeveenateneaien 3 52 3 6 2 Message Components and Structure cc ccceeesessssceeecceceeceeeeeeeaaaaeaeaeaseesssseeeeeeeeeeeeeeeeeeeeeeaaaaas 3 52 3 0 Sample Messages and Their Meaning 5 0 ccsasaseeewsecnseutirnsseavenndsnenasanseenyuseniecebacasaateseuesieeaedsiagssens 3 53 304 What b Aciially Sen na MessanE yncericne reinn nE RER 3 54 E ARD EAS C TEC OE S a A E ARA 3 54 SOC LIS IN Uy r E E EE E O RS 3 54 3 1 Up radmg SSM Firmware aay peco a sonc ye seeneseaonoan aia ononainenonenenih AE EEEE EEEE EENE ERAR 3 55 IRER T SG a E EE E O A E T E smeatasinns 3 55 SrL UPa Proce a E E E eee ree 3 55 See LOUDIEG TOO I a E E E ee 3 56 25 Working withthe AI gaya caters soetee sen noneeepscionti stones E T NEE E EE E 3 57 38 1 T rnme the
16. Dialup Special e Host Name Address TPC IP default address is Pronk Nene Host Name Addess 192 168 206 110 use the unique and valid address 10 10 10 110 defined for your site Host Setting Usemame Password Phrase e Username TPC user name service Anonymous Password Phrase TPC user password eel a TIPS Use the Initial Local Folder to store the location Paulos rola J where you keep the TI install files Enter ISMP in the re e Initial Host Folder text region to save steps later M E E EEE EAS 4 Keep other settings as default Click OK to go back to the Host List window 5 Under the Advanced tab ensure the selection to Use PASV mode is unchecked Figure 3 43 6 Inthe Host List window click your desired site and then click Connect to connect to the TPC FTP server Both devices should now appear in the FTP windows Hast Timezone 7 Transfer the file from the PC left side of screen to the ama TPC ISPM folder right side of screen NOTE PC ea aai SECUMD should be pointing at SSM HEX The TPC should be bte o pointing at the IPSM folder Port 21 Defaut Commands fter Connection 8 Close the FTP program and reboot the TPC r Accoun 3 7 3 Troubleshooting e If FFFTP fails to download files properly reconnect the TPCServer and try again Cancel Help e If FFFTP still fails to download files properly re boot the TPC by disconnecting then re connecting it Figure 3 43 Ho
17. Service Admin Advanced Main Status Custom Advanced Adin About Change Py Preference Lamp Lamp History Lens Test Pattern User 15 22 48 Figure 3 22 Advanced User Menu Options 1 8 characters required for login Editable when adding a user or to change current login Re define the password for the current login Add delete other users having the same or fewer rights Upon entering the User menu your current TPC user name appears in the User Name box For example if you logged on as Advanced the User Name box will display Advanced Other user names visible in the drop down list will be those with the same or fewer rights none will have more rights For each name their corresponding user rights appear in the User Level box directly below Table 3 13 Summary of Advanced User Menu Options ADVANCED USER MENU OPTIONS User Name Upon entering the User menu this box displays the name of the current login The pull down list displays all other user names having equal or fewer rights Factory Defaults Service Admin Advanced For new names use 1 12 characters the box above When adding a user User Levels can be chosen from in a pull down list note that only User Level Upon entering the User menu this box displays the rights of the current login read only These rights determine which TPC menus and functions are available The User Level tracks with different user names in th
18. be achieving the expected footlamberts as reported by the TPC It is a good idea to periodically recalibrate footlamberts refer back to Figure 3 32 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE 3 9 3 9 1 CP2000 XB User Manual Section 3 Operation Working with the Lens A Vertical M ized Bi Vertical The CP2000 XB lens mount secures the primary zoom lens to Oist the projection head It provides 1 setup adjustments for correct y Anchor oO boresight and 2 automatically controlled focus zoom and Horizontal p L Boresight LOO 0O N offsets for general use To save the focus offset and zoom Bolt settings to the channel you must make the adjustments using ana Lock the motorized lens mount adjustment features in the Main es Unlock ens Lens menu or Custom Lens menu from the TPC Using the Emergency Override knobs on the lens mount to adjust these positions does not save the settings to the channel They are designed for temporary emergency use therefore hone reference settings will be lost once the channel changes If used click Lens Reset from the Advanced Lens menu to ensure ILS settings are properly recalled An optional auxiliary lens 1 25x or 1 26x can be installed into Motorized Horizontal Offset lt gt Focus Vertical Boresight Bolt Figure 3 52 Anatomy of the Lens Mount an optional auxiliary lens mount then swung into place i
19. gamma2 6 is typically used in theatres Gamma files name and content are all currently pre defined Also known as look up tables B 5 Appendix B ASCII Messages Function Code Examples CHRISTIE Description and Parameters GPIO Assignments GIO requires v2 7 or higher GIO 13 LampOff GIO 13 h LampOn GIO I3H GIO I3h lampon GIO I3L GIO I31 lampoff GIO 03 SystemHealth GIO 03 GIO 03 System Health Allows macros to be assigned to GPIs and GPOs Important Changing to a 3D channel with GPIO usage will permanently delete the macro assignments for those GPIOs therefore it is suggested that those GPIOs used for 3D channels not be used for macros P1 input 1 5 or output 1 5 P2 Macro Name Predefined GPI macros LampOn LampOff DouserOpen DouserClosed AuxLensIn AuxLensOut Channel 101 through Channel 116 Predefined GPO macros System Health Lamp State Douser State Auxiliary Lens State Image Scaling Enable Disable IMS Enables or disable image scaling 0 disable 1 enable Intelligent Lens System ILS requires v2 9 or higher Method of reading and writing ILS information See Section B 2 4 Intelligent Lens System ILS Internal Test Pattern ITP ITP RGB 12Bbit Split Ramp ITP Enter t
20. gt if possible see Figure 2 10 left If forced to be off center such as when a film projector is already present try to optimize aim as shown in Figure 2 10 right This will slightly increase side keystoning but will minimize horizontal lens offset required NOTE Unlike film projectors it is best to keep the projector lens surface as parallel to the screen as possible even if it is significantly above the screen center wear i TYPICAL COMPROMISE Screen Center a Off center Projector Center Aimed projector Figure 2 10 Centering lt gt AERIAL VIEWS CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE i Section 2 Installation amp Setup 2 3 2 When a particularly short throw distance combines with a very wide screen you may have to forfeit some aim and stay more parallel to the screen In such cases some lens offset can reduce the keystone distortion Later when your projector is up and running adjust precise image geometry and placement as described in Section 2 10 Basic Image Alignment Throw Distance Throw distance is the distance between the projector and the screen Figure 2 11 For any installation placing the projector at an accurate throw distance is necessary in order for the image size to closely match your screen the farther the projector is from the screen the larger the image With zoom lenses you ll want to know the approximate minimum and maximum image sizes
21. not moving moving Related commands are Intelligent Lens System ILS Lens Horizontal Offset LHO Focus FCS and Zoom ZOM Measured Color Gamut MCG Use OnSite MCGD as the reference point for color proc What MCGD is currently in use Reply indicating the OnSite MCGD is in use PNG 032 001 002 Request for basic projector information which includes projector type and current software version Reply indicating cinema projector present 32 and its current version of software is v1 2 P1 32 always indicates a cinema projector P2 Major version 0 99 P3 Minor version 0 99 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix B ASCII Messages Function Code Examples Description and Parameters Power PWR Turn the lamp projector OFF or ON 0 off 1 on PWR 0 PWR 1 PWR 000 PWR 001 Processing Mode PRM PRM 0 Turn the projector lamp OFF Turn the projector lamp ON The projector lamp is OFF The projector lamp is ON Current processing of incoming source data 0 non cinema only 1 full cinema processing path PRM What is the current processing path PRM 001 Cinema processing path is currently in effect Projector Address ADR ADR 192 168 206 100 Sets which projector identified by its network address will be controlled by the TPC upon the next re boot Examples might include 192 168 206 210 or 192 168 206 117 etc
22. read only Apply LiteLOC settings to the current channel only checked Custom Advanced Admin About eee Lamp Light teria etal een erste Amps ae gen Rea ding from light walts Sm l wattsi oly pproximate Lamp Power He Fo Oo Ty Foot Lamberts gt esa rel lr reading read only 0 0 FL i i Hours 153 Page 1 Page 2 3D Control Lamp 11 11 06 Figure 3 13 Custom Lamp Menu Options Table 3 7 Summary of Custom Lamp Menu Options CUSTOM LAMP MENU OPTIONS Lamp Per Channel When enabled LiteLOC setting is applied to the specified channel When disabled all channels will use the global LiteLOC setting Maintains a chosen light level at the screen over time the lamp ballast will gradually increase power to the lamp as necessary until it reaches the maximum level possible for the installed lamp To disable LiteLOC temporarily or permanently clear the LiteLOC Enable checkbox or adjust Lamp Power directly Indicates what percentage of power appropriate for the installed lamp to supply to the lamp automat ically overriding any LiteLOC setting that may be in effect This causes the bar graph to rise or fall but the LiteLOC line and set value will not change unless Set is pressed defining a new LiteLOC setting See Table 8 1 Minimum and Maximum Lamp Power by Lamp Type on page 8 5 for lamp power ranges With the desired light output measured at the screen press Set to automatically enable Lit
23. refer to Section 2 7 Connecting the Ballast and connected to the projection head connect its integral line cord to AC Then Set Lamp Type NOTE Service installer required PANNID e Explosion hazard Keep the projection head OFF until you have defined which lamp type is installed Before powering up the projector and igniting the lamp the installer must define in projector memory which size lamp is installed otherwise you risk severely overdriving or underdriving a lamp At the TPC go to the Advanced Lamp menu password required Click New Lamp and enter the lamp type serial number and of hours logged on the lamp size of the lamp currently installed in the projector factory default 2 0 kW Refer to Section 3 Operation if you need help using the TPC menus Set Cable Length In the Admin Lamp menu see Figure 2 30 use the Cable Length m text box to record the length of high voltage DC cables connected between your lamp ballast and projection head This value regulates the voltage drop that occurs over distance and ensures that adequate voltage reaches the lamp Particularly in a projector rented for temporary installation the setting may have to be changed from its last use Adjustment range is 2 30m 62 100 ft Record which lamp Main Status Custom Advanced Admin About is installed OTE Ballast Cable Length m 15 NOTE 2 0 kW Lamp must 3 0 kW be OFF Foot Lamberts Calibration 4 5 kW Min
24. 2 8 DD ODT OMS 1S i OIA spat tec cee E E E E E E E E E E E ESE 2 8 23 Projector Position and Mouni Mo en ee ei E Es 2 8 FETO MOn AL ERO A O e ust ener eseeatatiocensas 2 8 2o LEON DI serena A E EE ENEE E EEE AA 2 9 Calculating Throw Distance ss ceanassosagarersinceadswadaanasoasaaassonagaieeoemedenseasenesoundeanseuanaeacseneeomseueenoacsor 2 9 NettiCal ANC Honzo POSION sesine rer En E mee eavlneneanasianesnes 2 10 pees E 18 2 a EE E EE A AEE T EE E E A eee T eee 2 10 NOC T a E EE ee ere 2 10 Alternative Method of Describing Vertical Offset nnnnnnnnneenesnseeesnnnrnnnrrrrrrrerrrrrerrrrrrrrrerns 2 11 Hor zoma LPO La 6 erna E E AEE E A EAA E meee ernen eee 2 11 Alternative Method of Describing Horizontal Offset nnnnnnnnnnnnnnnnnnnnrrrrrrrrerrrrrrrrerrrrrreen 2 12 2 3 3 Floor Mounting and Leveling ou ccccccccccccceccceeeesessesseeeeeeeceeceeeeeeeeeeseeaaaaasesssseeeeeeeeeeeeeeess 2 12 A Ee So ne ee eo 2 12 2 A A UC Ai SS CNA Oe E OU E ETE EN E A E O E EET 2 13 AN E E A EEE E AA E E OA I AE eee ta 2 13 eC ta OC re OI A A E E EE E T EE E A E EA 2 13 255 OSE AN a e E AE N E E sbaanaandgonrannnssseeersheleneandiea 2 14 Carry ine Movine ihe Projection Head sissioni N O S 2 14 Hara Forni E a A EE 2 14 Using the FredFrame M sriid eneren eere n a O EEEa ESEE ESEE a EE i 2 14 TE E E sae apenenatenenmeteaness tase ceadte 2 14 CP2000 XB User Manual i 020 100163 04 Rev 1 06 2009 Table of Contents 2 4 Install
25. 4 6 Basic Ways to Achieve Flat and Scope Displays CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 Section 4 Cinema Operation Section 4 Cinema Operation CHix IS TIE l 4 3 4 3 1 4 6 Selecting the Cinema Source NOTE For details regarding all TPC functions refer to Section 3 5 Using the Touch Panel Controller Via Touch Panel Controller As described in Section 3 5 Using the Touch Panel Controller cinema displays are usually pre configured so that any user can correctly display a desired feature simply by selecting the corresponding button on the Main menu of the Touch Panel Controller There is a maximum of 32 display buttons available at any one time 8 per page with most users locked out of other processing controls available in other Touch Panel Controller menus For cinema sources in particular which are displayed according to strict parameters pre defined by the producers of the feature and implemented in the projector by a CP2000 XB installer administrator or trained operator this simplicity ensures that the intended display can be selected quickly and easily by any user Figure 4 7 To change to a new feature do the following e Make sure the CP2000 XB and TPC are both powered up and operating normally On the Touch Panel Controller select the Main menu tab e On page or 2 of the Main menu press the desired channel button the image will update according to the display configuration defined for it
26. 6 Repeat all steps every 6 months in permanent installations 7 Maintain vane switches as described in Section 6 3 Maintenance and Cleaning NOTE f the exhaust duct becomes significantly blocked or if a fan fails the projector s airflow sensor should trigger a shutdown before the projector becomes overheated or unsafe Regardless check the airflow periodically CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE i Section 6 Maintenance 6 3 6 3 1 6 3 2 Maintenance and Cleaning To help ensure optimized performance and reliability regularly check electrical optical and other components as described below Warning SHOCK HAZARD Disconnect projection head and ballast from AC at BOTH wall breakers Electrical Do the following every 60 days or 500 hours always disconnecting from AC first e Check the contact surfaces of positive anode and cathode negative connections for cleanliness Clean electrical contact surfaces as necessary to prevent contact resistance from scorching connectors e Verify that all electrical and lamp connections are tight Optical Unnecessary cleaning of optics can be more harmful than helpful increasing the risk of degrading delicate coatings and surfaces In this projector check only the lens and lamp reflector maintenance of other optical components requires a qualified service technician Check these components periodically in a clean dust free environment using a hi
27. 6 5 Won O C NEE gaen rr E E E 6 5 PPE a E O E E E N N E ENER 6 5 Ca E EO e E em AEA A EAN 6 6 Cean ne Me REEE OT sarea a E EE TE E A AEE 6 6 6 3 3 Other Components 0 ceeccccccccccccccsessseeeccccceecesueseeeccccceeesausseeeeeccceesssauaseeeeeceseeeeauaeeeeeceeeeeeeeeaas 6 6 CP2000 XB User Manual v 020 100163 04 Rev 1 06 2009 Table of Contents 04 Replacme te Lamip and FINNET cca casscanstesecesvavececuenveriecueesanenseuseminenecuemwer eee 6 4 4 Lamp Replacement Procedure oeeie eree 6 4 2 Filter Replacement Procedure c ccc esssssssseeeeecccccceeeeeeeeeasaaaeeeseseeeees Co ae 2 eer ay a Boi ener ne meee eee mn Cen ee ne ee 7 Troubleshooting Tee ONS E seats estan OE E E nau eee ecu eae E en suaues Tle POK LOW WV ML NOTIE oae E E AE eee PALI e E E E E E ane meatase meee yeas 7 2 1 Lamp Does Not gnite cc ccccccccccceeeceeeeeeseeeseeseeeeeeeeeeeeeeeeeeeeeeaaaags P22 Lamp OCS GOES OL raa R Tel gt NO Lamp Curent INCA IIT 5 5 52 s0strcs eyenciamegecainetuaesuauetsacteasieuetausgesesiausseen 7 2 4 Flicker Shadows or Dimmness c ccceececsecccesecccescccesccceeccnseceeseceesecees 1 2 LampLOC Does Not Seems to Work vicescascediniesinensserseninesseuavivereelevacsiees 7 2 6 LiteLOC Does Not Seem to Work cccccscssccccccceeeeeeeeeeesesseseesesssaaes To NO E s39 assays ve one ose ciseeaesasoons evaanusen a cobennsic one peamaaessceenaetes GP Sap MUN STM aes pce sens ec te swe as econ vs n
28. A list of the last 10 recorded lamp serial numbers appears here along with their dates of entry and number of hours logged This is a read only menu unless activated via the New Lamp button on the Lamp menu which adds edit boxes and a Save button for recording in memory the serial number of a new lamp and the number of hours it has already been in use if applicable Main Status Custom Advanced Admin About Date Time Type Serial Number Hours 2006 03 20 10 37 JBOS03 6EMY rd E gt Preference Lame Lamp History Lens Test Pattern User 15 21 06 Figure 3 19 Advanced Lamp History Menu Options CP2000 XB User Manual 3 31 020 100163 04 Rev 1 06 2009 Section 3 Operation 3 32 CHRISTIE Advanced Lens Menu Use the fields provided in the Lens menu to select a lens type and record its serial number Select lens type from drop down list Intelligent Lens System Cali brate ILS Custom Advanced Admin About Diag Primary Lens Serial Number 1 25 1 45HC 1234455 Suxilary Lens Serial Number None fitiiiisdit Intelligent Lens System Installed Calibrate Lens Reset On Startup 11 11 06 g Figure 3 20 Advanced Lens Menu Options Main Status Enter serial number for the newly installed lens Table 3 12 Advanced Lens Menu Options ADVANCED LENS MENU OPTIONS Primary Lens Auxiliary Lens Serial Numbe
29. Content Number of inputs 2 Standard supported VESA Digital Visual Interface DVI D Connector Type 24 pin female DVI D NOTE Currently supported DVI formats i e non cinema formats are listed on Section 5 1 Compatible Non Cinema Sources Control Ports RS 232 connectors 2 9 pin D female A Non ASCII PC communication B Christie proprietary accessories only Ethernet connectors 2 RJ 45 female Std 100 base TX 100 Mbps max GPIO connector 1 37 pin D female Refer to Figure C 1 and Figure C 2 TPC connector 1 6 pin XLR See Touch Panel Controller below Ballast Control Port 1 9 pin D male RS 232 w proprietary protocol for ballast only Ballast Interlock Port 1 9 pin D female 5V TTL compatible opto isolated at for ballast only ballast end Touch Panel Controller Type of Display 5 7 diag color LCD backlit Integrated Operating System Microsoft Windows CE Communication Interface w CP 10BaseT Ethernet Power Requirement 05 A max at 24 VDC 10 Current Rating 2 0 A max Interface Connector 8 pin DIN bayonet locking Memory 64MB CP2000 XB User Manual 8 3 020 100163 04 Rev 1 06 2009 Section 8 Specifications 8 5 Power Specifications Projection Head Projection Compartment AC near Panel B at front Connector type and rating Voltage range nominal Line frequency nominal AC input rating Max inrush current Max current consumption Max power consumption Lamp DC Max operating
30. Current range shown includes over drive which is 10 more than the original lamp rating CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 8 Specifications Table 8 1 Minimum and Maximum Lamp Power by Lamp Type Lamp Type Min Lamp Power Max Lamp Power Type Xenolite Stand by lamp power level for 4 6 kW 50 of lamp s maximum current rating Stand by lamp power level for 2 3 kW 75 of lamp s maximum current rating Motorized adjustment of position 3 axis 0 25 range for each Recommended screen widths 2 0 kW 45 ft nominal 3 0 kW 55 ft nominal 4 5 kW 65 ft nominal 6 0 kW 75 ft nominal All screen sizes approximate and assuming 1 5 screen gain if lt 70 ft and 1 8 screen gain if gt 70 ft 8 7 Regulatory 8 7 1 Audible Noise 70 dBA maximum NOTE Does not include customer supplied external extractor fan 8 7 2 Safety e UL 60950 1 and CAN CSA C22 2 No 60950 1 03 1 edition bi national e IEC 60950 1 200 8 7 3 EMC Emissions FCC CFR47 Part 15 Subpart B Class A Unintentional Radiation CISPR 22 2003 A 1 2004 EN55022 1998 A2 2003 Class A Information Technology Equipment CP2000 XB User Manual 8 5 020 100163 04 Rev 1 06 2009 Section 8 Specifications CHA IS TIE 8 7 4 8 8 8 8 1 8 8 2 8 9 8 6 EMC Immunity CISPR 24 1997 EN55024 1998 A1 2001 A2 2003 EMC Requirements Information Technology Equipment Environment Operating Environment Temper
31. Determining Screen Brightness fL In order for the TPC to display screen brightness in footlamberts fL you must measure screen brightness at both extremes of lamp power minimum and maximum for a given lamp type and record these two readings in the TPC Admin Lamp menu available to installers These measurements establish a range stored in memory from which the TPC can interpolate all other lamp power settings converting them to approximate footlamberts for display in the menus Repeat the calibration if you ever switch to a different lamp type size For more information about menus and footlamberts refer to Section 3 Operation Basic Image Alignment NOTE Assumes projector is fully assembled and powered up in its final location This procedure ensures that the image reflected from the DMDs is parallel to and well centered with both the lens and screen This initial optical alignment is the foundation for optimizing images on the screen and must be completed before final boresight adjustments To save the focus offset and zoom settings to the channel you must make the adjustments using the motorized lens mount adjustment features in the Main Lens menu or Custom Lens menu from the TPC Using the Emergency Override knobs on the lens mount to adjust these positions does not save the settings to the channel They are designed for temporary emergency use therefore hone reference settings will be lost once the channel changes If used click
32. FL 6 0 kW ee im Sae Source Screen Gamut IP Contig General Lamp 11 11 06 Figure 2 30 Set Cable Length Power up Power up the CP2000 XB system as described in Section 3 2 Power Up Procedure CP2000 XB User Manual 2 23 020 100163 04 Rev 1 06 2009 Section 2 Installation amp Setup CH IS TIE l 2 9 2 9 1 2 10 2 24 Maximizing Light Output Upon powering up the projector with a newly installed replaced lamp adjust lamp position to help ensure optimized operation as well as peak Watts 4701 brightness at the screen you do not need an image Scie telat al 110 0 a eee displayed yet Once you have done this LampLOC __ pLamploc ae eee adjustment the lamp will be well centered and 0 0 FL distanced correctly from the remainder of the ee ry ol illumination system E ha Preference Lamp Lamp History Lens Test Pattern User Lamp menu Watch the gauge on this menu After 2 a 3 minutes with the projector using an internal light amie Ea sensor the best lamp position will be established and Figure 2 31 Align the Lamp the DO AUTO button will no longer be disabled At this point light output is optimized NOTE Lamp must be on and the shutter open during LampLOC adjustment however the projector does not need to be displaying an image v 60 z 145 At the TPC automatically optimize lamp position by clicking the DO AUTO button in the Advanced
33. INPUT REFERENCE NOTES Select the option matching your source type and how the 3D sync is supplied e A LEFT B RIGHT Select if your 3D source provides separate left and right data via 2 cables at the A and B SMPTE ports This assumes the 3D stereo sync signal is included with the image data inputs rather than supplied separately at the GPIO port e WHITE LINE or BLUE LINE Select only if using a single 3D input signal in which an embedded white or blue line at the bottom of each frame identifies left vs right and an additional separate 3D stereo sync input at the GPIO port is not present Short line Left long line Right NOTE Requires single 3D input Not currently supported e ASSIGNED GPI Select only if using a single 3D signal requiring a separate 3D stereo sync input at the GPIO NOTE Requires single 3D input not currently supported L R DISPLAY REFERENCE NOTES Select the option describing how you are supplying the 3D stereo sync signal to the projector e NOT USED Select Not Used if your 3D source provides separate left and right data via 2 cables at the A and B SMPTE ports In this configuration the image data includes the 3D stereo sync signal an addi tional separate 3D stereo sync input at the GPIO port is not used e ASSIGNED GPI Select only if using a single 3D input signal requiring a separate 3D stereo sync input at the GPIO NOTE Requires single input not currently supported L R OUTPUT POLARITY NOTES e TRUE 3D
34. Lamp History menu When to Replace the Lamp Assuming the Lamp Expiry Message checkbox has been enabled in the Advanced Preferences menu recommended an expiry message will br Sepp 2 Ladi Signal Y 23 74Hz appear on the TPC as an alarm window when the lamp has reached its LB Cine IPM 26 Not Detected defined Lamp Limit and should be replaced a l pasga Projector Hours Palit Total Lamp Hours Lamps should also be replaced when one of the following events occur 8 Lamp i keed 43 Current e Image quality is compromised by excessive flicker a aa e Lamp hours have exceeded expected average life 15 37 21 R e Lamps are no longer able to maintain SMPTE specified light levels Figure 3 51 Lamp Hours Regardless of the Lamp Limit chosen never exceed the lamp lifetime by the hours shown in Table 3 24 as an old lamp becomes increasingly fragile and more prone to sudden failure or even explosion which can be damaging and dangerous For details on when to replace the lamp refer to Table 3 24 When to Replace Your Lamp Lamp kW Replace BEFORE 6 0SD 700 hours NOTE Hours shown here are greater than or equal to the pro rated credit warranted lifetimes Refer to Section 8 6 Lamps for more details Do not exceed Refer to Section 6 4 Replacing the Lamp and Filter for instructions Maintaining Footlamberts Over time as the theatre screen ages and dust and dirt collects on the port window the theatre may no longer
35. Lens Reset from the Advanced Lens menu to ensure ILS settings are properly recalled Ensure the CP2000 XB is properly positioned relative to the screen before you begin Refer to Figure 2 10 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 2 Installation amp Setup 2 11 Basic Optical Alignment Procedure l Display a good test pattern appropriate for analyzing image focus and geometry such as a single crosshair centered across the image COARSE FOCUS Do a quick preliminary focus and if available zoom adjustment with the primary lens only refer to Section 3 9 Working with the Lens Do not worry about consistency across the image at this point just center focus CENTER THE IMAGE IN THE LENS Holding a piece a of paper at the lens surface adjust offsets as necessary until Top Edge LEVEL the image is centered within the lens perimeter A full white field works best for this RE CHECK SIDE TO SIDE LEVELING With a good test pattern on screen double check projector leveling refer to Section 2 3 Projector Position and Mounting so that the top edge of the image is parallel to the top edge of the screen See Figure 2 32 Figure 2 32 Level the Top Edge 2 12 Offset and Boresight Alignment To ensure proper offset for your site and consistently good focus in all areas of the screen a primary lens must be installed and its lens mount precisely adjusted in relation to internal optics
36. Non Cinema DVI Inputs for Alternative Content cc eeeeeeeeeeees roo eo 0 615 60 Ue oa 0 See en ene eer eee BA MO Ci Pin COn aac Sets circuses smetiens tence ose sepane E vi CHRISTIE CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE i Table of Contents e eE E a E E E E E E A E E E 8 4 PPO S E a e EE E E E E E E E E 8 4 1 KW 3 Phase Ballast 38 8 1400 I 0T ccncccsiesssnvsontinassdossceutensretbedarstevasedouabacnanaensadonidestoancssiededs 8 4 a E 0 pe ee ee E E A E E E EA E A eee 8 4 S O O a E E ern erent 8 5 Sr le E NO E e E E E E E E 8 5 Te 2 E E E E E E A 8 5 TOENE ME O E E E E E EEA AE EOT A EEEE 8 5 CAE N T A atts ccc A AEE E deers E EEE EE 8 6 TE ONS No rare ene ccertce tw Kon e NAA EENE EE EEE AE EEA E E AT Ea 8 6 SE FOT MV LR Onne E eo E E E E ES 8 6 CaL NOOP NE EIVIN O sei EE ene eater E EA 8 6 E E a ace 7 ee EE E E ESE PAA A A E AE A EE 8 6 SO a EONO E EE E T EE E TEETE ERS 8 8 Appendix A Glossary Appendix B ASCII Messages BA KO EEA EAEE E EA E TEE E ETT B 2 B2 IN SS ae es Wiio Multiple PANU ORS errre iir en A E EN EE a E B 15 BAET MS e ERR a E E EE E E B 15 Additional Parameters for 001 System Errors and 002 System Warnings ccccccceeees B 15 Examples of Critical System Error 001 Messages 0ccccccccssssesessseessseeeeeeeeesessseeeeeeeeegs B 16 Examples of System Warning 002 Error Messages cccccccccccccceeeceeeeesseeeessssseeeee
37. O oooo0o000000000000000 O ooooo0o0000000000000 GPIO GPIO Port INPUTS viewed from underside OUTPUTS Pin 1 GPO 1 GPO 2 2 GPO 3 GPO 4 Pin 37 GPO 5 GPO 6 GPO 7 Figure C 1 GPIO Connector Pinouts As shown above each available pairing of pins is defined as either an input or output Configure a pin as an input if you want the projector to respond to an incoming signal or as an output if you want an external device to respond to the projector For example configure the pin as an output in order to drive an external IR emitter for 3D glasses or to automatically reduce room lighting when the projector is turned on 5 VDC External Supply Recommended Operating Point 5 mA Max Current 50 mA Forward Voltage Drop 1 1 V 5 mA 4 To Center lt 4 Pin of BNC To Shielding of BNC IR Emitter Figure C 2 Circuit for Power Supply If you are wiring your own GPIO cable for use with a server or 3D device such as an IR emitter or a polarizer follow the circuit diagram in Figure C 2 CP2000 XB User Manual C 3 020 100163 04 Rev 1 06 2009 Appendix C System Integration CH IS TIE C 2 1 Example GPIO and 3D Device 1 Assemble a cable according to guidelines shown in Figure C 1 and Figure C 2 2 Connect the cable to projector s GPIO port and to your 3D device 3 Inthe TPC s Custom 3D Control menu set Output GPO accor
38. RANGE KW AMPS 105 170 NOTE 4 Lamp Power setting of 110 will exceed the maximum values shown here by approximately 10 Adjusting Lamp Position LampLoc Align a newly installed lamp as soon as possible to ensure optimized lamp performance and peak brightness at the screen for the life of the lamp NOTES 1 Before adjusting a 10 minute warm up is recommended 2 You can adjust lamp position either before or after adjustment of Lamp Power or LiteLOC Use the Do Auto Button for LampLOC For best results in all installations align the lamp by pressing the DO AUTO button in the Advanced Lamp menu The motors and sensors in the projector will work together to precisely position the lamp for optimized performance and brightness utilizing filtering to eliminate signs of lamp flicker Once aligned this LampLOC setting can be considered fairly stable for the life of the lamp CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation When to Use the Individual LampLOC Buttons The individual LampLOC arrow buttons each of which moves the lamp in one direction only are provided as a reassuring back up should the DO AUTO button fail or if you feel a manual operator assisted lamp optimization will result in more output Either measure your results with a light meter at the lens and screen or simply watch the light output gauge in the Advanced Lamp menu Note that with these buttons you may
39. Refer to Section 3 5 Using the Touch Panel Controller for other operating details A 1998x1080 WUA 2048x558 Flat srz Scope sYZ A 1998x1080 UA 2048x558 G Flat PS Scope F3 1 Select pre defined ae source large button BA Reserved A Reserved 2 Image will change PCF Flat CF Scope A 1920x1038 A 1920x804 i Flat P3 Scope PS To additional sources f CH 25 32 15 17 00 Figure 4 7 Select the Desired Source NOTES 1 Depending on your expected needs your installer may or may not have configured all 32 buttons for use 2 Buttons may have any icon or text CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE i Section 4 Cinema Operation 4 3 2 Other Methods 4 4 Depending on your installation you may be able to select a source from a different controller in a remote location by sending ASCII commands via an Ethernet communication link Refer to Section 3 6 Remote Control of the Touch Panel Controller and Appendix B ASCH Messages Regardless of how the display file is selected the feature will appear on screen according to the numerous specific display settings defined for it If the display does not appear as expected on screen part of the display setup may not be configured correctly for the incoming source Try a different button on the Main menu If the image is still incorrect this source may have to be re configured Adjusting the Cinema Display For general users only the selection of a
40. Section 3 Operation CHA IS TIE l Responding to an Alarm Window Press the acknowledge button in order to hide the alarm window and access other TPC menus and try to solve the problem as shown in the right column of Table 3 2 Can Alarm Conditions Be Ignored Note that every alarm window indicates a new condition in a given session the alarm window will not reappear for a condition that you have acknowledged shunted but not yet solved However if you cycle the projector OFF and ON again any persisting alarm condition will trigger the alarm window again Although it 1s highly recommended that the monitored over temperature and fan speed conditions always be set to trigger a flashing alarm window default this trigger can be turned OFF if desired by clearing the appropriate Alarm Triggers checkbox in the Advanced menu Once cleared such conditions will only trigger the yellow or red Status warning button rather than a flashing alarm window This can be helpful in rare cases where the alarm window is erroneously repeatedly triggered with no detectable error condition Disabling alarm triggers is not recommended for normal operation Failed interlocks an SSM communication fault IC fault and lamp failures always produce an alarm window 1 e these alarm triggers cannot be disabled 3 5 4 TPC About Menu Main Status Custom Advanced Admin About z STi Exit TPC software and p o m alt return to Windows Sr
41. Setup 2 12 5 Add Auxiliary Lens If present swing the auxiliary lens in position in front of the primary lens It should magnify in the horizontal direction only stretching the image straight across the screen this requires that its aperture visible within the lens be vertically aligned with the screen If the image appears skewed loosen the locking ring on the auxiliary lens and rotate the lens as necessary until the wide image is horizontal Anamorphic 1 25x 1 FOCUS PRIMARY LENS With the auxiliary lens in place re focus the primary lens using focus knob The goal is good focus at center and on all sides 2 FOCUS AUXILIARY LENS If horizontal focus in the image needs improvement focus the auxiliary lens too rotate its barrel as needed 3 RECORD SERIAL NUMBER Enter the serial number of your anamorphic lens in Advanced Lens menu Wide Converter Lens 1 26x NOTE Use a gauge block or measuring device to establish basic alignment of the wide converter lens to the primary lens MAZEN Use the Wide Converter lens with the following High Brightness or High Con trast Zoom lenses only 1 45 1 8 1 1 8 2 4 1 2 2 3 0 1 or 3 0 4 3 1 1 FOCUS PRIMARY LENS With the auxiliary lens in place re focus the primary lens using focus knob The goal is good focus at center and on all sides 2 LENS CLEARANCE Adjust clearance between the primary and wide converter lens to match the values in the following table NOTE Measure from
42. TMD TMD 2003 08 13 14 21 00 Set read the time and date in the projector s real time clock TMD 2003 08 13 14 21 00 P1 Year yyyy P2 Month 01 12 P3 Date 1 31 day of month P4 Hour 0 23 24hr clock P5 Minute 0 59 P6 Second 0 59 CP2000 XB User Manual B 13 020 100163 04 Rev 1 06 2009 Appendix B ASCII Messages CH IS TIE l Function Code Examples Description and Parameters UID JSMITH PassWord Allows remote access to a projector where a specific user name and password is set up and required NOTE This command is only necessary when the remote access setting in the projector is set to login required P1 User Name e g JSMITH case insensitive P2 Password e g PassWord case insensitive Virtual Network VNC requires v2 7 or higher and TPC 60 66 VNC 1 Start VNC server NOTE Should only be used for training WACO Zoom ZOM requires v2 9 or higher ZOM 1264 Changes the zoom setting of the lens under motor control ZOM 1264 1 ZOM 1264 1 1 Write P1 Location P2 Approach direction NOTE Approach is optional 1 Positive to Negative Approach 1 Negative to Position Approach Read P1 Real time position P2 Current direction P3 Moving Status 0 not moving 1 moving Related commands are Intelligent Lens System ILS Lens Horizontal Offset LHO Lens Vertical Offset LVO and Focus FCS For single parameter functio
43. When installed and configured on a PC the PC and TPC can transfer files back and forth via FTP PC files appear in the left window TPC files appear on the right For this update to take effect you will be required to replace the SSM HEX file located on the TPC ISPM directory Right Window in FFFTP with the new SSM HEX file 1 Run FFFTP on a PC that is connected to the same network as the TPC At the main window click the Connect icon or File Connect menu The Host List box should appear Figure 3 41 FFFTP File Commands Bookmarks View Tools Options Help zix tle a xlolo DIBfm Eafe fi ol fe Sq DO epuninst exe 2004 02 11 13 29 66 237 exe C FFFTP exe 2003 05 10 11 19 344 064 exe B FFFTP te 2003 05 10 13 54 B history tt 2003 05 10 13 55 O JRE32 dll 1997 06 11 2 54 TPC FTP Server CMAX SoftwareLab ChristieDigital TPC FTP 108 Local FTP anonymous FTP site FFFTP Ver 1 92 Copyright C 1997 2003 Sota Figure 3 41 Main FTTP Window with Host List CP2000 XB User Manual 3 55 020 100163 04 Rev 1 06 2009 Section 3 Operation CH IS TIE l 2 From the Host List of FTP servers click the TPC FTP server and then Connect Or if using FFFTP for the first time click New Host to create a new connection to the FTP Server The Host Setting dialog box should now appear 3 Complete the Host Setting entries Figure 3 42 Profile Name name desired for TPC General Advanced Kanii Code
44. You must first remove the access panel located on the underside of the projector near the air filter see Figure 5 1 Drill an exit hole or leave the panel off 2 For details about connecting Christies Cine IPM 2K refer to the Cine IPM 2K User s Manual supplied with the device Each DVI port accepts and will auto detect the progressive scan digital RGB sources listed in Table 5 1 displaying most of them in their original incoming format Note that the projector cannot scale DVI signals over 48 Hz to a o different size and or aspect ratio Cine IPM 2K or g ail Note that each DVI port is a single link port for a single link cable connector only Using this pair of ports as a higher bandwidth dual link or twin link pair requires additional hardware and is not currently supported see Figure 5 2 N VI ma sa Table 5 1 Compatible Non Cinema DVI Sources All Digital RGB 8 Bit Figure 5 1 Non cinema DVI Source Connection Incoming Vert Processing Path Display Format Format Freq Required NOTES 1 Sources with can be VESA E EDID reported 2 Interlaced signals are not supported 3 The desired processing path for a DVI source is selected in the TPC Advanced Custom menu Non cinema processing is required for DVI sources with a pixel clock rate over 110 MHz which is the limit for cinema processing 4 The projector will attempt to automatically adapt to any incoming data format that is within t
45. and Inspect Reflector 1 Loosen set screws from negative cathode rear 7 64 and positive anode front 3 16 lamp connectors These screws are shown in Figure 6 2 Make sure to apply minimal torque and DO NOT STRESS the quartz tube 2 Carefully slip the positive anode connector off the front of the lamp 3 Handling by the cathode end only unscrew the lamp from the rear connector and carefully remove from the projector Immediately place the lamp inside the protective cover saved from previous installation and then seal it in a heavy carton on the floor where it cannot fall or be bumped Warning Handle box with extreme caution the lamp is hazardous even when packaged Dispose of lamp box according to safety regulations for your area 4 With the lamp removed visually inspect the reflector for dust Clean if necessary as described in Section 6 3 Maintenance and Cleaning STEP 7 Remove New Lamp from Protective Cover 1 Remove tape knurled nut and locking star washer if present securing the lamp within its cover 2 Handling at the ends only extract the lamp from the cover Set aside the protective cover for re use in your next lamp disposal or for warranty return of an expired lamp 6 8 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE i Section 6 Maintenance STEP 8 Install New Lamp 1 With protective clothing and shield on insert the threaded cathode end of the lamp into the negative lamp con
46. as compared to full on white ranging from 0 0 to 2 100 You may want to modify one or more gain values to precisely match color levels in other adjacent displays or to accommodate a studio s internal color management technique Gain would rarely if ever be adjusted for theatre use CP2000 XB User Manual 3 43 020 100163 04 Rev 1 06 2009 Section 3 Operation 3 44 WHITE TOLERANCE NOTES CHRISTIE If desired the chosen target for white White x y coordinates under Target TCGD may be relaxed by establishing a small tolerance box around it This box represents four coordinates 0 1 2 3 plotted on a 1931CIE Chromaticity graph and may vary from TCGD to TCGD If desired define new tolerance coordinates for the current TCGD to increase or decrease this tolerance area or to change its shape or location larger boxes relax the tolerance reducing the loss of light caused by precise matching Clear the checkbox if the projector s whites must precisely match the target white point typical for telecine use defined for the current TCGD If this match can be anywhere within the tolerance box typical for theatre use enter a checkmark The checkbox status 1s saved with the TCGD Keep in mind that some light is usually discarded for an exact match resulting in a dimmer image t is recommended that you enable the tolerance box for all applications requiring maximum brightness such as in theatres Do not enable the tolerance box
47. as described below If desired an auxiliary lens can then be added to widen images for scope cinema displays Warning 1 Jf the Motorized Auxiliary Lens Mount MALM is present ensure to move the MALM to the OUT position before performing any lens calibrate or reset functions on the Motorized Primary Lens Mount to prevent collision between the projection lens and the MALM 2 Hazardous moving parts Keep fingers and other body parts away NOTES 1 Projector must be fully assembled and powered up in its final location 2 Keep clear of rotating parts Remotely operated motors may start to spin without warning 3 Avoid long hair jewelry and loose clothing exposure to the knobs during manual adjustment 4 In case of emergency unplug the line cord to immediately halt movement of the lens mount A Vertical Offset Motorized Knob Mi Vertical Offset y Ni Anchor Bolt Horizontal p Boresight Va O Bolt l ma Horizontal Lock Offset Unlock Knob Lens Motorized Horizontal Offset Focus lt gt Vertical Boresight Bolt Figure 2 33 Anatomy of the Lens Mount CP2000 XB User Manual 2 25 020 100163 04 Rev 1 06 2009 Section 2 Installation amp Setup CH IS TIE l ears AJUE Olas Peres tens e rd es A 2 26 Project an image with the primary lens only Always adjust offset before boresight Important Ensure the correct lens is selected in the Advanced Lens menu before calibration to ensure you will remai
48. attain a slightly higher peak than with the DO AUTO button but the peak may not be centered on the lamp curve and lamp performance may not be optimized whereas the DO AUTO button also utilizes filtering to eliminate the effects of any lamp flicker In general use the individual buttons only when you feel it is unavoidable HOW TO ADJUST IF USING A LIGHT METER First obtain peak readings on a light meter centered in front of the lens then at the center of the screen For each button continue in one direction then back up when reading begins decreasing NOTES 1 Display a 100 white internal test pattern 2 Use a tripod to center the light meter with the lens Distance from the lens does not matter You may need an attenuator or wish to construct an internal foil aperture first 3 This is an optional procedure use the light output gauge in the Advanced Lamp menu if preferred 1 Adjust forward aft z until the brightness DEN ka Main Status Custom Advanced Admin About reading in front of the lens is maximized liteLoc Laug Light Amps lt 6371 2 Adjust left right x and up down y until the Enable an brightness reading in front of the lens is Measure at St f 8 lens then Lamp Power hr 75 0 E3 a TE maximized at screen Approximate Lamplor Foot Lamberts Re adjust forward aft z as necessary F A a act a z 145 4 Repeat Steps 1 3 as necessary Step 2 eu le Hours 153 l A a
49. called horizontal scan rate or line rate HORIZONTAL OFFSET The difference between the center of the projected image and the center of the projector lens For this projector this value is expressed as the maximum percentage of the image that can be projected to one side of the lens center without degrading the image quality HOT SPOT A circular area of a screen where the image appears brighter than elsewhere on the screen A hot spot appears along the line of sight and moves with the line of sight High gain screens and rear screens designed for slide or movie projection usually have a hot spot ILS The Jntelligent Lens System describes the ability of Christie projectors having a motorized lens mount to automatically return to lens settings previously defined for a particular channel Not available in cinema projectors such as CP2000 XB INPUT A physical connection route for a source signal described by a 2 digit number representing 1 its switcher projector location and 2 its slot in the switcher projector INPUT SIGNAL Signal sent from a source device to the projector INTERLACE A method used by video tape players and some computers to double the vertical resolution without increasing the horizontal line rate If the resulting frame field rate is too low the image may flicker depending on the image content KEYSTONE A distortion of the image which occurs when the top and bottom borders of the image are unequal in
50. commonly used A 8 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix A Glossary NON CINEMA Alternative program material such as concerts plays sporting events and potentially corporate training or conferenc ing presented in theatres in addition to motion picture exhibition A non cinema source connects to one of the projector s DVI ports NON SYNC Audio played in a theatre generally from a CD when the cinematic presentation is not running such as during intermissions and prior to the start of film presentation NON UNICODE The non unicode method of encoding produces a concise character set of 256 alpha numeric characters typically used in for ASCII messaging in most Western languages Virtually all TPC functions can be executed remotely via non unicode default or unicode messaging this is auto detected Refer to Unicode OPTICAL SCREEN A type of rear projection screen which re directs light through the screen to increase image brightness in front of the screen Screen gain 1s usually greater than 1 but audience viewing angles are reduced Rarely used in cinema applications PAL VIDEO PAL Phase Alternating Line video is a 50 Hz standard with 768 x 576 resolution It is found on some video tape and disc players used primarily in Europe China and some South American and African countries PARALLAX The difference in alignment when an object is viewed from one eye or the other PCF
51. cycling the projector otherwise important diagnostic files will be unusable 2 Never run Interrogator during a show as this could cause image disruption 3 Interrogator is also accessible through a separate login and password different from the service login Contact Christie tech support for assistance and password NOTE Password protected Figure 3 61 Status Interrogator Menu Options CP2000 XB User Manual 3 71 020 100163 04 Rev 1 06 2009 CHRISTIE 4 Cinema Operation This section explains how trained operators can use the projector for presenting cinema events such as movie releases stored on a digital media storage device Please read through these pages before displaying cinema for the first time A good understanding of all cinema functions and how to access them will help you to run an event smoothly and easily NOTE Before attempting cinema use the projector must be properly installed aligned and configured by a qualified service technician as described in Section 2 Installation amp Setup Refer also to Section 3 Operation e 4 1 Compatible Cinema Sources e 4 2 Image Formats e 4 3 Selecting the Cinema Source 4 4 Adjusting the Cinema Display CP2000 XB User Manual 4 1 020 100163 04 Rev 1 06 2009 Section 4 Cinema Operation CHix IS TIE l 4 1 Compatible Cinema Sources Make sure HD SDI from a digital media storage device or cinema server is connected to one of the A or B input ports at the rear of
52. digital cinema feature is accessible The precise processing which affects details of image quality is predefined in its display files such as Source Screen and many others These settings are password protected and accessible by trained operators or installers only Some releases also contain a metadata file which pre defines certain display settings attempts to re adjust during a presentation will be ignored If you feel the cinema display is incorrect or faulty contact the trained operator in your theatre who can correct or further customize the display file settings CP2000 XB User Manual 4 7 020 100163 04 Rev 1 06 2009 CHRISTIE 5 Non Cinema Operation This section explains how to display alternative content originating from a standard definition or high definition non cinema source such as a PC or other graphics devices or from Christie s Cine IPM 2K Such a source routes to a DVI Digital Visual Interface port in the CP2000 XB projection head and can bypass cinema processing when necessary 5 1 Compatible Non Cinema Sources e 5 2 Selecting the Source CP2000 XB User Manual 5 1 020 100163 04 Rev 1 06 2009 Section 5 Non Cinema Operation CHix IS TIE 5 1 5 2 Compatible Non Cinema Sources Make sure your non cinema DVI source is connected to DVI 1 or DVI 2 at the underside of the CP2000 XP projection head Figure 5 1 These connections are typically made at the time of projector installation NOTES 1
53. distance cable l p STEP 3 Install Lens Lamp and Heat Extractor Refer to Section 2 4 Installing a Lens Lamp and Cooling for instructions Figure 2 1 Installing the TPC STEP 4 Connect a Source Connect your desired source to the appropriate HD SDI cinema connector s on the Communications and Source Connection Panel at the rear of the projector NOTE To connect other types of sources such as alternative content through DVI or Christie s Cine IPM 2K you must remove the access panel located on the underside of the projector near the air filter Drill an exit hole or leave the panel off VAN ZL HD SDI Figure 2 2 Access to Cinema and Non Cinema Ports CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE Section 2 Installation amp Setup STEP 5 Connect to Lamp Ballast and Power AUNDE 1 Connect all 4 cables to the projection head prior to turning the ballast breaker on 2 Follow all labeling exactly HEAD TO BALLAST Connect all 4 ballast cables two DC power cables and two communication control cables between the projector rear and lamp ballast See Figure 2 3 BALLAST TO AC Connect the ballast s integral line cord to your AC supply you may have to first modify the plug for the AC at your site See Figure 2 4 NOTE Before connecting the ballast to AC a qualified electrical technician must make sure the ballasts plug type and Input Power Range Switch matc
54. essismemanteesour ans ssocedsmeaeuaets on snnntdastatsecenspintantasiomeanasient 3 67 FADS D ogee 816 50 cee eer mene errr een ee nee ee ea eer eer are eee eee ree a eee er renee 3 68 FAC Ak MAG ET COINS yes secest ed sssny scans a icusaaey ads yussasousis ess ayieadaa sada panda endo asaaepeedes 3 68 WY Co US er Interface IMS UIC TIOMS sce leeueed rs etanede yr apneseseepaceacdevaed idetsueieievsed ssiavetcdeuaeduisedsaeeesoetameeea 3 68 Oo D ITU BONN ae E E ee ee 3 69 Usne meS DITES Pa E e E E E 3 69 Image Breakup nsoeneesenessessseseseessssseseseesrsrersrererrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrerrrererrrern 3 69 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE CHix IS TIE i Table of Contents KOZDE C e E E E E te reenter Sr Torre 3 69 CO a l E E E E E EE teeters 3 69 Monon AIS ea A A I AE E EE A E E E ee eensoendea 3 69 Smole o D IL Does Not VV OTK sarrrreop rirnan AE x semana AE AE EAE 3 69 3 11 Workine with Servers anid DidONOStiGS ssrcrsoriserrr renie enteren Ee EEEn NEEE Eei Eert Eras 3 70 a C0 EN a E E A te ncssau ve sucasetaacansenepecterea pees ascters 3 70 US TV VIC Ae aa ratepagctec oases E EAE EEE 3 71 Staas Waiter OS All MONU osoren aenn T EAEE E 3 71 4 Cinema Operation ACODE Cen OCE aa E E E eeneenr eT ee 4 2 A aE POT a E E E E E E EE 4 3 4 2 1 Projector Variables Electronic and Anamorphic Resizing c c ceeesseesseseeeesseesessssseeeeees 4 4 PA E e e a e a
55. external extractor fan Install Lens es Primary Lens 1 Fully insert the assembly straight into the lens mount opening all the way back without turning With the lens fully back it will seat properly within the lens mount NOTE High Contrast lenses only have a flat on the rear flange Rotate the lens so that the flange clears two screws in the mount Also ensure that the UP label is at the top to ensure proper aperture orientation 2 Lock the lens assembly in place with lens clamp DOWN 3 Secure lens safety ring and tether to projector not required if projector is floor mounted NOTE The lens seals the projector head preventing contaminants from entering the area of main electronics Never attempt to operate the projector without a lens installed 4 Ifthe motorized lens mount is being used calibrate the lens every time a lens is installed See Section 2 10 Basic Image Alignment for details Auxiliary Lens Installation Optional NOTE The optional auxiliary lens mount is required for use of the 1 25x anamorphic or 1 26x Wide Converter lens producing 2 39 1 scope images If the auxiliary lens will be used it is recommended that you add the lens and its mount before final leveling boresight adjustment and the like Install only for those installations requiring full size 2 39 1 scope display mostly side masking screens obtained by optically stretching a pre squeezed image INSTALL THE AUXILIARY LENS MOUNT ON THE PROJEC
56. file for access in Custom menu Peecceeeet Eocene d eH Ca n cel n ew e a unsaved source settings Figure 3 24 Admin Source Menu Options Table 3 14 Admin Source Menu Options ADMIN SOURCE MENU OPTIONS Resolution Activate then record the x y resolution of your incoming signal such as 2048 x and 1080 y or 1920 x and 1080 y Note that resolution must match the incoming signal format assuming you want to display all of it and may differ from the original resolution that you want to recover See Resolution Notes below Offset Activate then record how much incoming data you wish to discard essentially delaying the starting point for processing Leave at 0 to process all available data See Offset Notes below Aspect Ratio Enter the aspect ratio of the original cinema format you are trying to recover usually 2 39 or 1 85 Because the incoming signal may be pre squeezed the aspect ratio entered here will not necessarily match that of the incoming aspect ratio See Aspect Ratio Notes below Slidebars Adjust resolution and or offset as desired Create Source Save current resolution offset and aspect ration settings as a Source file that will be accessible and applied from within the Custom menu Restore Cancel new unsaved source settings of resolution offset aspect ratio Apply current settings to the image without saving RESOLUTION NOTES To capture process all of the incoming data
57. film frames ACTIVE LINE TIME The time inside one horizontal scan line during which video data is present ACTIVE PICTURE The area of a video frame which carries image information As an example a total frame size of 1125 x 2200 pixels may have an active picture of 1280 active lines and 1920 samples per active line Compare to production aperture ALTERNATIVE CONTENT Non cinema program material such as concerts plays sporting events and potentially corporate training or conferenc ing presented in theatres in addition to motion picture exhibition Alternative content connects to one of the projector s DVI ports AMBIENT LIGHT REJECTION The ability of a screen to reflect ambient light 1 e light within a room from a source other than the projector in a direction away from the line of best viewing Curved screens usually have better ambient light reflection than do flat screens ANAMORPHIC Having or requiring a linear distortion generally in the horizontal direction Anamorphic lenses restore a scope CinemaScope or flat format film frame to the correct appearance by increasing its horizontal proportion The CP2000 XB uses a 1 25x scope anamorphic lens option only ANSI American National Standards Institute the organization that denotes the measurement standard for lamp brightness ANSWER PRINT A print made from the cut original camera negative with proposed final color timing and sound tracks furni
58. front feet of the projector and the screen Also called _Projector to Screen Distance Always use the correct Christie throw distance formula to calculate the proper throw distance 45 required for your lens THROW RATIO Throw ratio throw distance screen width A 12 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix A Glossary TINT Balance of red to green necessary for realistic representation of NTSC signals TMDS Transition Minimized Differential Signaling is the basis for DVI Digital Visual Interface TRAILER Motion picture material presented prior to screening of the feature so called because they were originally presented following the feature Trailers are generally manufactured and created by the distributor in close cooperation with the producer they are distributed by trailer specialists at no charge Types of trailers include previews teasers house and or policy trailers advertisements and public service announcements UNICODE The Unicode method of encoding produces a very large character set typically required for ASCII messaging in non Western languages such as Chinese Russian etc In unicode every number code is unique to a single character A limited number of TPC functions can be executed remotely via unicode or non unicode default messaging this is auto detected Refer to Non unicode VARIABLE SCAN The ability of a projector to synchronize to inputs with freque
59. if exact color performance is more crucial than overall image brightness such as in telecine applications RESTORE NOTES white Tolerance HE a x 0 333 y 0 3337 white Tolerance TE TE AE Figure 3 31 White Tolerance Non theatre P7V2 telecine White point will be matched exactly Theatre P7V2 theatre White point match is more relaxed This button enables you to return to the Gamut menu settings that were present when you opened the menu however the precise behavior depends on whether you are working with measured MCGD or target TCGD settings e To restore MCGD settings The Restore button is disabled unless you have used the Test button To cancel new MCGD settings and return to the previous MCGD settings the new settings must be tested via Test but ton but not yet saved If not yet tested you can either leave the menu and cancel the settings as requested by the dialogue box or attempt to save but cancel out of it If you have already saved a new OnSite file by pressing the Create MCGD the old OnSite file cannot be restored e To restore a TCGD FILE Select the Restore button any time before saving CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE Section 3 Operation Admin IP Config Menu Use the IP Config menu when you need to define or change the Ethernet settings i e network address of the projector and or its TPC NOTE Record any new settings on T
60. is a summary of the Interface Formatter Interface and Processor entries that appear below it in the About menu i e any change to one of these elements would automatically denote a new Engine version NOTE The remaining individual red green and blue formatters are independent of Engine version 3 5 5 TPC Custom Menu NOTE Password protected Requires Advanced Admin or Installer rights GENERAL DESCRIPTION The TPC s three Custom menus enable installers service administrators or advanced users to tailor projector processing as they wish for any type of incoming source including 3D material and collect these settings into a unique channel that any user can select at the Main menu Up to 32 channels can be defined e Custom Page 1 and Page 2 These two menus consist of numerous display settings that can be adjusted as desired then defined collectively as a custom setup or channel Each defined channel then appears as a button on the Main menu where any user can select it providing a reliable way to quickly and correctly change the on screen display to suit the source content Alternatively if a pre defined Projector Configu ration File PCF has been supplied with distributed content rare and the Use PCF checkbox checked those Custom options which are already defined in the PCF Source Target Color Color Space Gamma and LUT CLUT disappear from the Custom menus and are protected from further modification The channel defined in
61. ports A and B NOTE Use of a single input consisting of both left and right data is not currently supported Sync Output Device e IR emitter for controlling the L R gating switching of active glasses OR e Pi Cell polarizer for controlling a screen that has a silver polarization preserving surface for use with passive glasses Custom 3D Sync Output Cable GPIO such as available from RealD e For routing the projector s output sync to your Sync Output Device connect from the projector s GPIO NOTE Accessed from underside of the projector as shown in Figure 2 2 Access to Cinema and Non Cinema Ports on page 2 2 to the emitter or polarizer Refer to Section C 2 The GPIO Port for GPIO pinouts and other 3D sync cable details Power supply for your Sync Output Device typically wired with the custom GPIO cable Proper 3D configuration defined in the TPC s Custom 3D Control menu For best results use the 3D inter nal test pattern shown in Figure 3 58 CP2000 XB User Manual 3 65 020 100163 04 Rev 1 06 2009 Section 3 Operation CHix IS TIE l 3 10 3 Supported Hardware Setup 3 66 Section 3 10 4 Other Hardware Setups shows the general hardware configuration currently supported Use either an IR emitter to control gating in active glasses or a polarizing cell and Z screen with passive glasses NOTES 1 A configurations require a custom 3D Sync Cable such as supplied by RealD for the GPIO port 2 A pull up power supply
62. possible from a given throw distance so that the most appropriate lens is installed at the site throw distance screen width throw ratio of lens Calculating Throw Distance Once you know the screen size and lens type present calculate the required throw distance Screen m x Throw Ratio Approx Throw Distance 1 25 1 45 zoom A lens lt i Figure 2 11 Estimating Throw Distance Example NOTES 1 f your projector is tilted up or down in relation to the screen typical in large venues and or elevated installation throw distance still represents the smallest measurement between the screen and front bezel 2 Remember that throw distances are calculated from the screen to the front bezel of the projector rather than its foot centers To figure throw distance from foot centers add 8 74 22 2 cm As shown in Figure 2 11 throw distance is approximately equal to the full horizontal width of the screen multiplied by the type of lens you are using For example if you are using a 1 25 1 lens the proper throw distance value will be approximately 25 more than that of the full screen width Once you know your screen width and lens you can estimate throw distance needed Or if you know the available throw distance beforehand you can determine what images sizes are possible with a given zoom lens Important For proper placement in any installation use the throw distance formula provided for your lens In addition keep in mind
63. pull down PDS 000 Reply indicating 2 2 pull down Save SAV SAV Immediately save all changes to flash memory rather than waiting for eventual auto save or a power down Screen Format SCF SCF filename Selects a custom or standard screen file stored in the TI head Use this screen format file stored in projector memory SCF What is the current screen format SCF 1920x1080 Current screen format filename is 1920x1080 Screen Orientation SOR SOR 0 Sets the position of the projector relative to the screen 0 Front 1 Rear 2 Inverted Front 3 Inverted Rear SOR What is the current screen orientation setting SOR 0 Current screen orientation is normal front position Select Input SIN SIN 0 Select which projector P1 and input P2 to use P1 Input 0 Input A SMPTE cinema 1 Input B SMPTE cinema 2 Dual SMPTE cinema 3 DVI A non cinema 4 DVI B non cinema 5 DVI Twin 6 CineIPM input on DVI A 7 CineIPM input on DVI B 8 CineIPM input on DVI Twin 10 bit 9 CineIPM channel on DVI A 10 CineIPM channel on DVI B 11 CineIPM channel on DVI Twin 10 bit P2 required for P1 6 7 The input number 1 8 or channel number 1 25 of CineIPM Available for P1 6 and P1 11 only The above will change the input on the selected channel only 1 16 To change the input on a different channel the source number must be used in front of the parameter that is
64. reservoir to ensure adequate circulation within the projection head The reservoir which 1s located in the igniter compartment is factory filled and does not require draining before projector transit Check regularly for level and leaks and top up as necessary Trained operators only Power Cables Heavy duty DC lamp cables between the ballast and the projection head are 6 100 feet 2 30 meters in length depending on which option was ordered with the CP2000 XB system The ballast projection head and heat extractor fan all include their own line cords CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation Projection Head The projection head houses all critical illumination and optical components as well as the DLP Cinema processing technology responsible for combining light and incoming source signals into brilliant high resolution cinema displays Cinema source inputs connect to the rear of the projector non cinema connects to the underside of the projector Projector function is controlled via the TPC or other communication link from either an Ethernet or RS232 controller The projection head is closed and locked for normal operation Security Locks TAMPER RESISTANT HIGH SECURITY for PROJECTION HEAD Components in the projection head are protected by an electronically monitored high security lock on the lid This interlock strictly controls access since every opening of the lid is 1 elect
65. serial link is adequate for DCP Librarian use or for downloading new main software both tasks require a qualified Christie service technician It cannot be used for ASCII messaging since the TPC Eic0q 00 recognizes Ethernet only and is too slow for servers C 1 2 Cine IPM 2K Connect the Cine IPM 2K s custom RS 232 cable from the rear of the Cine IPM 2K to the CP2000 XB serial port labeled RS 232B located on the underside of the projection head you must remove a small cover for access The RS 232B port uses Christie proprietary protocol and is compatible with Christie accessories only Linking the Cine IPM 2K to the RS 232B port enables Cine IPM 2K sources to be selected at the TPC Important Do not use RS 232 B port with other devices C 2 The GPIO Port The 37 pin GPIO connector located on the underside of the projection head provides a flexible method of interfacing a wide range of external I O devices to the projector often so that an event on one device automatically triggers an event on the other The pins on this connector that are configura ble using the TPC s Custom 3D Control menu are identified in Figure C 1 NOTE Pins not shown in Figure C 1 are reserved for other uses and cannot be specified at the TPC C 2 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix C System Integration O ETHERNET o O O O O Re O
66. temperature may be too high Check air filter and sensor Check liquid cooler fan Red DMD is too hot Power down and cool projector Reduce lamp power Ambient temperature may be too high Check fluid flow and level Check air filter Check liquid cooler fan Blue DMD is too hot Power down and cool projector Reduce lamp power Ambient temperature may be too high Check fluid flow and level Check air filter Check liquid cooler fan SSM is too hot Power down and cool projector Reduce lamp power Ambient temperature may be too high Check fluid flow and level Check air filter Ballast is too hot and has shut down Cool then cycle the projector down and up normally If the over temp recurs there is a cooling problem in the ballast that may require service Check ballast fan OTHER FANS TOO SLOW A primary fan is too slow or stopped Replacement fan may be required Card cage fan is too slow or stopped Replacement fan may be required Laminar airflow is too slow or stopped LAMP PROBLEMS Lamp Life has expired Replacement of the lamp is recommended Unexpected lamp off Increase Lamp Power Check that DMDs have not overheated An interlock may have momentarily tripped Lamp may have to be replaced Replacement LAD filter or fan may be required Lamp strike failed If interlocks are OK make sure the 220V connection near Panel C at the rear of the projector head on the underside is still plugged in If lamp re try stil
67. that due to lens manufacturing tolerances for lens focal length actual throw distance can vary 5 or more between lenses described as having the same throw ratio CP2000 XB User Manual 2 9 020 100163 04 Rev 1 06 2009 2 10 Section 2 Installation amp Setup CH IS TIE l Vertical and Horizontal Position Refer to the offsets shown here for help in determining how high or low to install the projector in relation to the center of the screen and or how far off to one side Vertical Position Describes the elevation of the projector in relation to the screen For many typical large venue rental staging installations and theatres the projector will be above screen center An ideal vertical position helps ensure that 1 images will be accurately rectangular in shape rather than distorted into a keystoned shape with non parallel sides and 2 focus and brightness will remain optimized Vertical position of the image can be offset that is placed higher or lower in relation to lens center using the Up Down Offset buttons from the Main Lens menu Starting with no offset the 2048 x 1080 image from this projector can be moved by a maximum distance of 540 pixels resulting in all of the image displayed above or below lens center Figure 2 12 Vertical Tilt Describes the angle of the projector in relation to the screen Ideally the projector should be inclined so that the lens is perpendicular to the screen so that the face of the lens
68. the CP2000 XB projection head see right The identical A or B cinema ports use the SMPTE 292M bit serial interface standard and will auto detect cinema source formats shown in Table 4 1 Figure 4 1 Cinema Source Connections Table 4 1 Compatible Formats for Cinema Source Orig Format Vert Freq Scan Type Display Format Standard Progressive SMPTE 274M 1998 NOTE Uses 1125 total lines per frame SMPTE RP21 1 2000 SMPTE RP 211 1920 x 1080 30 Hz Prog Segmented 1920 x 1080 30 Hz Frame 1920 x 1080 29 97 Hz Prog Segmented 1920 x 1080 29 97 Hz Frame 1920 x 1080 25 Hz Prog Segmented 1920 x 1080 25 Hz Frame 1920 x 1080 24 Hz Prog Segmented 1920 x 1080 24 Hz Frame 1920 x 1080 23 98 Hz Prog Segmented 1920 x 1080 24 Hz Frame SMPTE 295M 1997 NOTE Uses 1250 total lines per frame SMPTE 295M 1920 x 1080 1920 x 1080 25 Hz 4 2 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE j Section 4 Cinema Operation Source Orig Format Vert Freq Scan Type Display Format Standard Progressive SMPTE 296M 2001 SMPTE 296M 1280 x 720 60 Hz Progressive 1673 x 941 60 Hz Progressive 1280 x 720 59 94 Hz Progressive 1673 x 941 59 94 Hz O C SMPTE 260M 1999 NOTE This standard does not officially support 60 M SMPTE 372M 2001 DUAL LINK All SMPTE 292m 1998 single link formats see above are available as 12 bit 4 4 4 dual link with the same performance format e M 1 001 e Signal
69. the expected incoming source resolution and aspect ratio such as 1920 x1080 or Mk7 default Choices are pre defined using DCP Librarian or the TPC Admin menu CP2000 XB User Manual 3 21 020 100163 04 Rev 1 06 2009 3 22 Section 3 Operation CHA IS TIE l CUSTOM PAGE 1 MENU OPTIONS Target Color Identifies sets the special color processing called Target Color Gamut Data established for a given presentation Default P7V2 Theatre Color Space Identifies sets the method of color decoding for the current source Default RGB for all DVI sources Default YCbCr for all cinema sources 1 e SMPTE A or B ports Gamma Identifies sets the desired gamma a k a de gamma correction needed for proper tonal range of the source material for example a grayscale test pattern will be neutral and smoothly graduated In theatres the only gamma setting currently needed is PL2 6 These components are part of a pre defined PCF that controls image processing for a given source When Use PCF is checked these components disappear from the Custom menu and are protected from further change Custom Page 2 Menu Use the auxiliary lens with this channel Custom Advanced Admin About 5 Auxiliary Lens In Pull Down Re Synec Current channel Screen Pull Down Sequence Screen area crop amp lens Choices gt Scope 2 2 Pull Down A Define frame sequence def
70. the lamp ballast power in order to maintain a constant light output LUMEN The unit of measure for the amount of visible light emitted by a light source Rarely used in cinema applications LUMINANCE The signal representing the measurable intensity comparable to brightness of an electronic image when the image is represented as separate chrominance and luminance Luminance also expresses the light intensity of a diffuse source as a function of its area measured in lumens or candles per square foot 1 lumen per square foot 1 footlambert SMPTE RP 98 calls for a luminance of 12 to 22 footlamberts for theatre screens Refer to Footlamberts LUX The amount of visible light per square meter incident on a surface 1 lux 1 lumen square meter 0 093 foot candles MENU A list of selectable options displayed on the Touch Panel Controller METADATA Descriptive data about the format of the content 1 e data about data When receiving metadata digital cinema projectors will know the correct aspect ratio of the image and the sound processor will know the correct format of the audio all without effort on the part of the person setting up the show on a particular projector NTSC VIDEO A 525 line resolution video output format of some video tape and disc players There are two types of NTSC National Television Standards Committee video NTSC 3 58 and NTSC 4 43 NTSC 3 58 is used primarily in North America and Japan NTSC 4 43 is less
71. the lamp ballast will immediately stop power ing the lamp TAMPER DETECTION caused by unlocking the projector lid Failure is also logged and prevents dis play of incoming CineLink encrypted cinema source material FAILED LAMP IGNITION Failure to successfully strike the lamp COMMUNICATION ERRORS SSM and or I7C links may be malfunctioning It is also recommended that the following additional conditions always be set to trigger an alarm window default Select these triggers in the Advanced Preferences TPC menu e OVER TEMPERATURE caused when the temperature in the card cage red blue DMDs integrator prism or SSM has exceeded the operating specification e FAN SPEEDS caused when a main intake fan card cage fan or the laminar air flow device fan fails or is too slow e LAMP EXPIRY appears when lamp has reached the end of its life as defined in the Lamp Limit set ting Important For normal operation do not disable alarm triggers CP2000 XB User Manual 3 51 020 100163 04 Rev 1 06 2009 Section 3 Operation CHix IS TIE l 3 6 3 6 1 3 6 2 3 52 Remote Control of the Touch Panel Controller Most TPC projector functions can be controlled remotely typically at a controller via simple bi directional ASCII messaging on an Ethernet communication link To control these TPC functions remotely via your own controller you must open an Ethernet socket between your controller and the valid TPC address Refer
72. to YCbCr or YPbPr COMPOSITE VIDEO The output of video tape players and some computers characterized by synchronization luminance and color signals combined on one output cable CONTRAST RATIO The degree of difference between the lightest and darkest areas of the image CONVERGENCE The alignment of the red green and blue light elements of a projected image so that they appear as a single element In this projector convergence can be adjusted by Christie service personnel only CURVED SCREEN A projection screen which is slightly concave for improved screen gain Curved screens usually have screen gains which are greater than 1 but viewing angles much less than 180 Curved screens are not recommended for use with this projector A 4 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix A Glossary DCDM Digital Cinema Distribution Master A file or collection of files formatted for exhibition and comprised of all the components of the title A reference size of about 200 GB per title is likely DDC The Display Data Channel VESA standard enables communication between PCs and monitors and is based on E EDID protocol DMD Digital Micromirror Devices used in this projector for processing red green and blue color data DHCP Dynamic Host Configuration Protocol is a commonly used client server networking protocol It enables a DHCP server to allocate valid IP addresses to projectors det
73. to direct incident light to an audience A flat matte white wall has a gain of approximately 1 Screens with gain less than 1 attenuate incident light screens with gain more than 1 direct more incident light to the audience but have a narrow viewing angle For example An image reflecting off a 10 gain screen appears 10 times brighter than it would if reflected off a matte white wall Curved screens usually have larger gain than flat screens GVG Grass Valley Group formerly part of Tektronix More specifically the gvg file format used for compressed video audio and timecode stream transfer in the Profile video server products proposed for standardization by SMPTE and as a primary component of MXF Initially implemented on Fibre Channel using FTP with TCP IP but extensible to XTP or other protocols Previously called GXF General Exchange Format HDCP High bandwidth Digital Content Protection protocol of keys and encryption helps prevent DVI source material from being copied HDTV High definition Television 1035 1080 and 1125 lines interlace and 720 and 1080 line progressive formats with a 16 9 i e 1 77 aspect ratio A 6 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix A Glossary HELP SCREEN A display of help information regarding the current task or presentation Not available in CP2000 XB HORIZONTAL FREQUENCY The frequency at which scan lines are generated which varies amongst sources Also
74. to the complete instructions in Section 3 6 6 Setup and Shutdown later in this section Note that only one physical connection is permitted at any given time and access to remote functions may be limited by the installer Do not use an RS 232 serial link Understanding ASCII Message Formats All remote control information passes in and out of the TPC as simple messages consisting of command code and any data related to it Such messages can be a command to set a projector parameter at a specific level such as changing to a certain channel Or the controller can request information such as what channel is currently in use the projector then returns the data in a reply message Regardless of message type or origin all messages use the same basic format and code as shown in Figure 3 38 Where applicable a message can expand to include additional parameters of related data Message Format Function Examples CHA 103 SET set channel to 103 or Controller CHA1 03 3 2 _ REQUEST what s current channel CHA From Projector l REPLY channel is 106 CHA 106 Figure 3 39 The Message Formats SHADED MESSAGE IS FROM PROJ Message Components and Structure START AND END OF MESSAGE Every message begins with the character and ends with the character Note that if the start character is received before an end character of the previous message the partial previous message is discarded FUNCTION CODE Th
75. used SIN s1 1 changes channel one input to 292B B 12 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix B ASCII Messages Function Code Examples Description and Parameters Simple Network Management SNM requires v2 7 or higher and TPC 60 66 SNM TOD SRF filename Select the stored source file defining incoming resolution and desired aspect ratio for the current display SRF What is the current source format SRF 1280x1024square Current source format filename is 1280x1024square Shutter Control SHU SHU 0 SHU 1 Open or close the electronic quick douser 0 shutter open 1 shutter closed Source Change SRC Same as CHA command Stop TI Communication Terminate TPC Application STP 0 Start TI communication 1 Stop TI communication 2 Terminate TPC application 3 Reboot TPC System Status SST Method of reading projector information See Messages With Multiple Parameters later in this Appendix Target Color Gamut TCG TCG filename Select the stored target color gamut file to apply to the current display TCG TCG P7V2 3D Controls TDC What TCGD is currently in use The P7V2 TCGD is in use TDC 1 Turn 3D controls ON OFF or sets specific 3D controls TDC 10 420 Example shown Set dark time to 420us For all other 3D controls see Messages With Multiple Parameters later in this Appendix Time amp Date
76. users can access TPC functions remotely or not at all or whether a login is required Data Logging Define the extent of activity to record in an Ethernet accessible TPC data log default Errors only A good data log can be helpful when troubleshooting but use with caution Detailed logging will slow TPC responses Note that when the memory card becomes full logging continues by simply writing over the oldest entries Error Message Enabled When enabled an error message will be sent via Ethernet whenever an alarm condition is encountered CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation Record light measured for Select to both extremes automatically reduce lamp power to its minimum of power e Measured at screen e Projector will lt be able to inter polate future light output in footlamberts Select to automatically increase lamp power to its maximum Select to implement new values j Figure 3 36 Admin Lamp Menu Options Table 3 20 Summary of Admin Lamp Menu Options ADMIN LAMP MENU OPTIONS Footlamberts Activate each text box to automatically drive the lamp at its minimum or maximum power record light Calibration measured at the screen for both extremes in power defining a range of footlamberts possible Light readings fL appearing elsewhere in TPC will then be interpolations based on this range Push SAVE to implement new values NOTE Re cali
77. voltage Max start up voltage Max current consumption Max power consumption Connector type With extractor CHRISTIE 1 IEC 320 compatible 10 A rating 200 240 VAC 10 50 60 Hz 1OA 35 A 3A 700 W 46 VDC 155 VDC 180 A 6600 W Female CAM Lock receptacle red Male CAM Lock receptacle black 7 kW 3 Phase Ballast 38 814001 01 Nominal Voltage per o Nominal Operating Range Line Frequency Inrush current max NOTE excluding lamp Current consumption per phase max 6 6 kW Power consumption max Current rating continuous of 3 phase AC input at breaker Internal Breaker Power Switch BALLAST OUTPUT TO PROJECTION HEAD Operating voltage range Start up voltage open current Operating current range Ripple Control ports 8 6 Lamps CXL CDXL Lamps kW CXL CDXL 20 2 0 CXL CDXL 30 3 0 CXL CDXL 45 4 5 CXL CDXL 60 6 0 CDXL 60SD 6 0 Current Range amps 60 85 90 120 95 155 105 165 8 4 e 208 VAC N America Japan e 400 VAC Europe e 200 230 10 N America Japan e 380 415 10 Europe 50 60 Hz nominal lt 50 A e 28 A 208 VAC N America Japan e 16 A 400 VAC Europe e 14 4 kVA 9 1 kW all regions 30 A all regions 50 A 18 46 VDC 125 155 VDC 50 180 A 1 max 25 C See Control Port and Interlock Port on previous page Average life Hours 3500 2500 CXL 20 requires adaptor kit P N 003 001728 XX NOTE
78. wide converter lenses Communication ports for remote control of the projector via PC or other controller High security tamper resistant lid lock with all access electronically monitored HDCP decryption on both DVI inputs allows display of copy protected alternate content Triple Flash functionality capable of projecting full resolution 3D images under a 6 2 frame rate multiplica tion NOTE DLP version 13 1 or higher is required How the Projector Works PROCESSING amp PROJECTION The CP2000 XB accepts a variety of cinema or DVI compatible non cinema signals for projection on front screens typical in a commercial theatre or other large screen applications High brightness light is generated by a short arc Xenon lamp and then modulated by three Digital Micromirror Device DMD panels responding to incoming data streams of digitized red green or blue color information As these digital streams flow from the source light from the responding on pixels of each panel is reflected converged and then projected to the screen through one or more front lenses where all pixel reflections are superimposed in sharp full color images STACKING amp RIGGING A projector secured in the optional FredFrame can be stacked and if desired flown with another framed projection head using the Roadie 25K CP2000 X Stacking and Rigging Kit and standard rigging techniques to secure the two frames together Each frame provides precision roll pitch and yaw adj
79. 000 XB User Manual 020 100163 04 Rev 1 06 2009 3 13 Section 3 Operation CHA IS TIE l ENVIRONMENT Projector Hours hours projector has been powered up and communicating with the TPC Total Lamp Hours hours logged for all lamps ever installed Lamp hours logged on current lamp LiteLOC TM On Off At Maximum Power Critical safety and or operation monitoring Lamp Fan rear of projector OK Failure Failure also triggers an alarm window Extractor Fant for ducting to outside world OK Failure Failure also triggers an alarm window Lamp Door louvered lamp door OK Failure Failure also triggers an alarm window High Current OK Failure Failure also triggers an alarm window OK Failure Failure triggers an alarm window and stops CineLink 2 encrypted cinema processing Critical internal temperatures in C or F 55 69 C warning gt 70 C critical 60 64 C waming gt 65 C critical 70 74 C warning gt 75 C critical 55 59 C warning gt 60 C critical RPMs of 1 primary fan exhaust side of proj Fan 2 Intake 2 RPMs of 24 primary fan exhaust side of proj LAD RPMs of laminar airflow device for DMDs 3 14 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation C sue pmenserter Dewane D C e a roa o rowa i Crome i Crowan Crom OOOO S rorem a Tear A Taine Cromos resem Terres Cow OOO S Feree e ewer w row i rommaa rome S C
80. 048 x 1080 as the cinema pixel clock rate is limited to 110 MHz Use PCF Enter a check to use a pre defined PCF for this source and prohibit further Custom adjustments the PCF components of Source Color Space Gamma LUT CLUT and Target Color will disappear then select the desired PCF from the Predefined Configurations list Clear the checkbox if you wish to adjust the Custom settings this is currently recommended for all cinema use Refresh Button Updates all Custom settings such as Gamma Target Color etc to include any data newly added to projector memory via DCP Librarian setup software or TPC Admin menus Select to clear the current channel or all channels and return to factory defaults Input Identifies sets the location connection of the current source such as cinema ports A or B or a DVI graphics port Note that use of the twin and dual link DVI options requires special hardware Refer to Section 5 Non Cinema Operation Data Format Specifies the source type 8 10 12 bit and whether or not it is packed The projector will process the incoming signal according to the data format selected here Note that available data formats depend on which projector input is selected and will reset to a default value if an input has not yet been selected Use of DVI dual requires a separate adapter at the DVI connectors and use of DVI twin requires a special source Data format settings are not included in a PCF Source Identifies sets
81. 1 or request status aml NOTE Requires Motorized Anamorphic Lens Mount optional Ne Channel Icon CHI CHI S101 1 Assign second icon in list to represent channel 101 Range 0 15 Note the S required when specifying a channel other than the current channel CHI 15 a 16th icon in the list to represent the current channel Range 0 CHI What is the current icon CHI 004 The 5th icon represents the current channel Channel Name NAM NAM S108 Chicken Little or Changes or assigns a name to a particular channel Always pre AMS108 Chicken Little ceded with S so that the name is assigned for this source only NAMEN CHA CHA What is the current channel CHA S101 Reply from proj that new channel is 101 first channel Range 101 132 Color Space Selection CSP CSP P7v2 Set the color space gamut or TCGD to P7v2 CSP What color space is currently in use CSP P7v2 The P7v2 color space is currently in use B 2 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE Function Code Examples Appendix B ASCII Messages Description and Parameters Data Format DTF DTF Data Logging DLG DLG 1 DLG DLG 002 Selects the source type and packing mode for the current input Cinema source A or B 0x00 4 2 2 unpacked 10 bits color default 0x01 4 2 2 packed 12 bits color 0x02 4 4 4 unpacked 10 bits color 0x03
82. 3 Operation CINEMA VS NON CINEMA SOURCES Display setups for digital cinema servers are carefully configured when the projector is installed so that presentations will be automatically optimized and require no further adjustment A user need only select the relevant channel button Displays of non cinema or other alternative content such graphics or video sources connected to DVI ports are also usually pre configured for easy selection Refer to Section 5 Non Cinema Operation for details about non cinema applications and display adjustments Other Methods of Source Selection Depending on your installation you may be able to select a source via communication from a different controller Regardless of how the display file is selected the feature will appear on screen according to the specific display settings recorded in that file If the screen display does not appear as expected this indicates that the display setup is incorrectly configured for the incoming source Try a different display file If the image is still incorrect the display setup may first have to be re configured with new settings Contact the trained operator responsible for updating display setups 3 5 9 Errors and Alarms Encountering the following conditions will always trigger a flashing red alarm window at the TPC ACTIVATED SAFETY INTERLOCK caused by an open lamp door a failed extractor or lamp fan or an open fire alarm switch For any safety interlock breach
83. 3 2 Chief CP2000 XB components are identified and explained below Exhaust Vent for duct and Extractor Fan Touch Panel Projection Head Anamorphic Lens Mounting Holes Channels Leveling Communication for FredFrame Feet 4 amp Source Offset Vertical Connection Panel Offset Ballast Connect 3 Phase 7 kW Ballast On Off Breaker 3 Phase Status LEDs amp Voltmeter Figure 3 1 Basic Projector and Related Components Air Filter Intake air flows through the filter before circulating in the front compartment to cool the main electronics Replace the air filter whenever the lamp is replaced or sooner in dusty dirty environments Check filter condition monthly Refer to Section 6 4 Replacing the Lamp and Filter for complete instructions Ballast Breaker ON OFF The breaker on the lamp ballast serves two purposes 1 it is a power switch for the CP2000 XB ballast and 2 it protects against over current conditions of 50A or more The breaker must be ON in order to enable normal CP2000 XB system power up and operation If faulty or major excessive AC is detected the breaker will trip to OFF in order to prevent damage Try moving the breaker ON again if the breaker continues to trip OFF this indicates a major fault and the AC problem must be resolved Possible causes might include shorts damage to lamp cables or very excessive AC NOTE This switch does not ignite the lamp You must use the TPC Lamp Button The
84. Adjusts the horizontal offset of the output lens under motor control LHO 1023 1 LHO 1023 1 0 Write P1 Location P2 Approach direction NOTE Approach is optional 1 Positive to Negative Approach 1 Negative to Position Approach Read P1 Real time position P2 Current direction P3 Moving Status 0 not moving 1 moving Related commands are Intelligent Lens System ILS Lens Vertical Offset LVO Focus FCS and Zoom ZOM CP2000 XB User Manual B 9 020 100163 04 Rev 1 06 2009 Appendix B ASCII Messages B 10 Function Code Examples CHRISTIE Description and Parameters Lens Primary LNP requires v2 7 or higher LNA 1 25AN 1234567 P1 Lens type P2 Lens serial number Valid Lens 1 25 1 45HC 1 45 1 8HC 1 8 2 4HC 2 2 3 0HC 3 0 4 3HC 4 3 6 0HC 5 5 8 5HC 1 25 1 45HB 1 45 1 8HB 1 8 2 4HB 2 2 3 0HB 3 0 4 3HB 4 3 6 0HB 5 5 8 5HB Lens Vertical Offset LVO requires v2 9 or higher LVO 264 LVO 264 1 LVO 264 1 0 MCG OnSite MCG MCG OnSite Adjusts the vertical offset of the output lens under motor control Write P1 Location P2 Approach direction NOTE Approach is optional 1 Positive to Negative Approach 1 Negative to Position Approach Read P1 Real time position P2 Current direction P3 Moving Status 0
85. Ballast Connection and Power up CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 2 3 Section 2 Installation amp Setup 2 4 HEAD TO AC Connect the Christie supplied IEC 320 220V 15 amp line cord to a single phase 208V AC supply Do not substitute other cords Input power required is 200 240 VAC 10 50 to 60 Hz 3 amps for 208 V Warning Do not attempt operation if the AC level is not within the specified voltage and power range for the projection head 180 265 AC EXTRACTOR Also plug the extractor fan into the projector Refer to Section 2 4 Installing a Lens Lamp and Cooling At this point the projection head is ready for use The voltmeter should display the incoming voltage e PROJ STATUS light should be green e Light engine compartment fans near the front should be running e Remainder of projection head will be off STEP 6 Set Lamp Type and Cable Length NOTE Service installer required CHRISTIE Extractor Fan 200 240 VAC 200 240 VAC Figure 2 5 Connecting Projection Head to AC Supply NAGANNE Explosion hazard Keep the projection head OFF until you have defined which lamp type is installed SET THE LAMP TYPE Before powering up the projector and igniting the lamp the installer must define in projector memory the size of lamp installed otherwise you risk severely overdriving or underdriv ing a lamp At the TPC go to the Admin Lamp menu pa
86. CP2000 XB USER MANUAL 020 100163 04 CHRISTIE CHix IS TIE i Table of Contents 1 Introduction PUTRE PIO CON ae EE E E T EEE EEA 1 2 PELNO E O a E odie E E A E E aimee ie 1 2 LEZEN O AE ES e A E A A A E N 1 2 LES HOn LG OPS Or VV E a E made ames tneaadeewenaqeaepenslscasasis a cueiaccouensetndupensvaanes 1 3 1 2 List Of Components 2 0 ccssssseeeeeseeeeeeeeeeeeeeeeeeeeeaeaaseeeeeeeeeeeeeeeeeeeeeeeeeeeeeaaaeaaaaaaeeeeseseeeeeeeeeeeeeeess 1 4 BPA WO 0c e106 WO ra 0 RET 2 0 8 oi 0 cee ee 1 4 Th Zo OME AE we UMM IN I ress cates a E E E A spagsunaesiesiescnaneiad E E 1 4 ko UTC MAS Reco ANG SEI y ICG OMA ES cscs AE aerate tame meatus 1 5 LA Who should Use This Mantal eenean 1 5 1 4 1 Labels and Marking 0 0 cccecsceccceccecececccecceccececeeecceaeeceecseeaaeeeeeceaeeeeeeeeaeeeeeeeaceeeeeeeeeeess 1 6 WA EVO Or ay IC ae NOON S eeens ne ceri xesnetstion cg civepmesnsnnti acne anne anita eae areacioamenearanteaeannee tender 1 6 2 Installation amp Setup PAED CN o EE E E EE EEA EA E EAE EE E E saeco 2 2 Z2 Taon e Oner OS eie E E 2 5 PA e E OCS E A E E A esse cine AE EAE E O E A aeancee 2 5 Fon Ce CU SPAN O gor E E E E eneioneueens 2 5 Roar ooe eO a E E E E eee 2 6 L OE MUL a E E E E 2 6 PSN TE SOC U R r E E E E E EEE A EEE 2 6 Displaying Doth Flatand SCODE pmrssermesheri rerni EE EEEE EERE AN RANE So 2 7 2 2 4 Ambient Lighting cccccssssssssesssssessesesseseseesseeseeeseeeesseeeeeseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeas
87. E Repeat Steps 1 4 but reading at the screen Steps 1 i EEA instead of at the lens od arg 6 Reset Lamp Power or LiteLOC if desired 11 10 37 Figure 3 49 Adjusting Using a Light Meter 3 8 5 Stand by Mode Close the douser shutter to put the projector in a cooler ven Sere aen eee eae lente Gaul lies l About Diag stand by mode where lamp power is reduced to 50 of its Sp SFA i 2048x858 maximum rating or 75 if using a 2 kW or 3 kW lamp die gu sosaicinp 1998x1080 pA 2048x658 power when Upon opening the douser and restoring the image the lamp HA A e eet power will return to its previous setting A Reserved A Reserved ow PF Flat PCF Scope 920x1038 WA 1920x804 iF Scope PS O AA 15 17 00 Figure 3 50 Lamp Power in Stand by CP2000 XB User Manual 3 61 020 100163 04 Rev 1 06 2009 Section 3 Operation CHA IS TIE l 3 8 6 3 8 7 3 8 8 3 62 How Old is My Lamp Main LiteL Ore When a new lamp is installed and its serial number recorded Bo Advanced Lamp menu the lamp timer resets to 0 and begins e logging time for the new lamp This total appears in both the a SS ee a Advanced Lamp menu and the Status menu See right i rn ae F ve 2 i The Status menu also shows Total Lamp Hours which is the EO wy ole Hours 274 accumulated time logged for all lamps installed thus far Each past lamp 5 poao NewLamp log also appears in the Advanced
88. Gamut Data TCGD files for new color gamut performance and set how closely you want to match the target white Recording the projector s uncorrected color performance is typically completed as a final step like a calibration after installation For this one time procedure the installer measures initial native 1 e uncorrected colors at the screen enters the data as Measured Color Gamut Data on the left side of the Gamut menu and typically saves an MCGD file called OnSite By default the projector will use this MCGD to calculate and implement precise processing modifications needed to achieve any target color gamut on screen essentially compensating for the type of port window screen lens light output ambient light and other current environmental factors influencing on screen colors These various industry standards for color performance TCGDs will then be consistently achieved from source to source and from site to site If the environment degrades or changes such as if an auxiliary lens is swapped on and off or if an internal optical module is replaced create one or more new MCGDs naming them as desired To use an MCGD file as the reference file for target color processing such as with a certain source and or lens select it in the Custom menu CP2000 XB User Manual 3 41 020 100163 04 Rev 1 06 2009 Section 3 Operation 3 42 White Tolerance Create MCGD Create TCGD Record x y coordinates for each uncorrec
89. IP Config menu then change the TPC s IP address in the same manner as you changed the projector s address Warning The first 3 octets of the IP address must match those for the projector See Steps 2 and 3 above NOTE This is the simplified explanation of valid addressing A trained network administrator may expand the range of valid addresses To implement the address changes in your projector and TPC re boot Important Do not forget to re boot the projector CP2000 XB User Manual 3 47 020 100163 04 Rev 1 06 2009 Section 3 Operation 3 48 Admin General and Admin Lamp Menus NOTE Jnstaller login required CHRISTIE From within the Admin menu an installer can access 2 additional submenus not available to any other user These submenus are primarily for defining critical system parameters such as the projector s lamp type user rights for remote access and the amount of data logged in projector memory Installers can also record minimum and maximum Footlamberts readings to establish a range from which other TPC lamp readings are interpolated and they can set whether Status menu temperatures appear in Celsius default or Fahrenheit A typical Admin General submenu appears below ID for projector location on net work Default y cj address Shown Main Status Custom Advanced Admin About Use valid address Eik E Prames i i for the site Frojector IP Address Define site lise 168 Pos 40 e
90. L R sync output from GPO will match L R of sync input e INVERTED 3D L R sync output from GPO will be the opposite of sync input left becomes right and right become left FRAME RATE N M NOTES Increase the display frame rate as necessary to reduce flicker from your source s EXAMPLE These N M ratios define how many frames to display per number of frames that 4 2 4 frames displayed form I complete image For all 3D use the bottom value is 2 indicating that two 2 frames per image frames left and right are combined into every complete display frame Set to the highest rate possible without image cropping CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE i Section 3 Operation NOTE Not for 2048 x 1080 6 frames 2 sources 48 Hz x 3 4 frames 2 sources 48 Hz x 2 Figure 3 12 Examples of Frame Rate N M For example when processing typical dual L R 3D signals of 24Hz a Frame Rate N M setting of 4 2 will generate 4 frames of output for every 2 frames of input at a final frame rate of 96 Hz For any source keep the final frame rate less than that of the projector which is 67 Hz for full 2048 x 1080 resolution Generally incoming 24Hz signals can be increased by a maximum factor of 5 2 DARK TIME and OUTPUT DELAY NOTES The dark time between incoming L R frames provides a brief interval of non image time in microseconds uS for your switching device such as shutters in gla
91. Lamp OWN Bat cct caecasaciaassmininsnanadicaasnmnenunseioigaitimamnaqreiuararatesateraanseetatesasetaeccae 3 57 ISa BEL On e E J 0 a E T EEE E EEE T ENE 3 57 3 8 3 Adjusting Lamp Power LiteLOC or Manually ccccccccccccccccccccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 3 58 oaa CECOT M E E A A E E E E E E 3 58 Ueno EATON T aee E E E E E E ere eee ee 3 59 3 84 Admusine Lamp Postion LampLOC eresi 3 60 Use the Do Anto Button tor LampLOC aciccctecteseaienssncapcocsuasavniawsenesesouctsnsauredentsorewadecuenncueeees 3 60 When to Use the Individual LampLOC Buttons 000 0 ccccccsssseseeeeceeeeeeaeseeeeecceeeeeeaaeeeees 3 61 Foye ee V LG le bh M e a ce ee ee eee 3 61 Sm om lo OT N Or 110 0 ae ener ren ae ere re ee ene ttre ene te ae ernment eee 3 62 Die Vy MSE WO ICD aCe WMG le AMO aos g acc cscae tet tncee st E EE E E E 3 62 38 9 Maina I POO LEAT C005 enan rnrn E TEE T 3 62 3 9 Working With the LenS sersierssresorirr iiet girieire enn union EE REE EEE EEE TEREE AR 3 63 Dek ASC EE NAC i S A E E E A EE E E A 3 63 PEE e a A E i TE E E E T E E ee eee ee eee 3 64 AOW OEN D E E EE cussion E EE E E E E 3 64 OLS DO DESC IDO aE E E A A A einen austen 3 64 AO Aiea DOIN ca Or D eee A E E EA A E A 3 65 SANE a E L E E E O O A N erste reenietaneecnereean 3 65 3 10 3 Supported Hardware SetUp sacasccsssaurscsceassceuinnsscnwsagescesasanasuvacanssuniunbaenesaeorsessaaeaonsiqasascmbacectecnes 3 66 3404 Other Hardware ose FIG ca necensycayantssancas ten
92. Mount and Auxiliary Lons MOUDE a5 cccscvencecetupeceeuneacusenersscaneveececenotctasisessteaneseruaunneneener 3 4 My St PECI sn a E E Go eseodestecacustarseamtetasdeacte 3 4 Bs ov 6 OO 0 ae nn EE E E E E E EA er eee ee 3 4 IPO WEE COADIC c E E aacheneaasacsssaasncasiea piace sosscaouaasivesengssvanceact 3 4 PONS CHO LCA se coeerceecnaseig cose se crag cca A A EA 3 5 UEC LOCKS occa eset E meet AE ATE A AEE E AT 3 5 Touch Panel Controller TPC cc ccc ccccccccccccccsssssssseeeeceeeeeecceccceeeesessusaaaaaaeeseseeeeeeeeeeeeeees 3 5 PONET UPTO T a e E eee cn ee eee ere 3 6 PONT DON 0 POCE E a A E EE 3 6 3 4 Introduction to the Touch Panel Controller ssiiesssoienineninn ai 3 7 TV a Ce Se IR TMS essences cece tac E E AE 3 7 SAN TRC PowerUp Del ats sess socscasasceccsuecoecesbasevadinnsesananniiaattaoaetanavanseeseebade lt atbaruesseaoatanneeieeemaniarse 3 8 re a ois 016 PE Gee oh a eee een ne ree ee eee eee 3 8 zo Urmo the Toh Pane k rath ONC Fas coast pa hassctsanasac oatsaatelasdantannasuduata aera mebaausas aclonsaanasutueeamaeitediouens 3 9 OLEC Mana WIC a a E E EE EA NA 3 9 Intelu eent Lens Syston IES scere E E E 3 11 Tor nane dls Pere n a R 3 11 ToEditAc ve Channel ILS SEINES srainnsear oE E E ES 3 11 To Temporarily Alter the Active Channel ILS Settings 0 0 ccccccccccccccceeeeeeeeeeeeeeeeeeeeeeeeeeees 3 11 OLEE aT M acess ca peck E E E gs iee yee vant coieasa E 3 11 PEAN 100 9 cane ne E E ee 3 16 FRCS OMG Vin Oy Cm AA
93. Normal Front e Inverted Rear Install Options e Normal Rear Image Orientation Remote Access e Inverted Front eee ee PF Mormal Front Toggle to use a Celsius Display different lamp mode amp power for each channel or to use one setting for all L i I aS see E Fa nur I zs Figure 3 35 Admin General Menu Options Table 3 19 Summary of Admin General Menu Options ADMIN GENERAL MENU OPTIONS Restrict who can access the TPC remotely e No access e Login required e Free Access Define the extent of data to be logged e Errors e Standard e Detailed NOTE Slows TPC response Send Alarm Window messages via Ethernet Projector IP Address Identifies which projector the TPC controls and always terminates in J0 99 All four values octets must be valid for your site For example perhaps you can use the default 192 168 206 Z0 to control a single projector installation Then use 192 168 206 1 to control a second projector at that site 192 168 206 212 to control a third projector and so on NOTE This menu does NOT define the projector s IP address Image Orientation Define the orientation of the screen relative to the projector Lamp Per Channel Enable to save a separate lamp mode power setting with each channel or disable to use a single global lamp setting for all Celsius Display Choose Celsius or Fahrenheit temperature display for Status menu Define whether all
94. PC Admin menu must match that of the projector 4 Ifyou still have trouble establishing communications with a projector added to an existing Ethernet network the projector s IP address is likely in conflict with another address already in use Contact your network administrator Cinema Displays Blank Screen No Display of Cinema Image CAUSE REMEDY 1 Confirm all power connections are still OK 2 Make sure there is no lens cap present 3 Make sure the douser shutter is OPEN button is on TPC Main menu 4 Make sure there is not a full black test pattern selected for display 5 Is the correct display file selected Check the Touch Panel Controller 6 Is the correct cinema port connected for this display file Check connections Severe Motion Artifacts CAUSE REMEDY Most likely there is a synchronization problem with reversed 3 2 pull down in 60Hz to 24Hz film to digital conversion in your source The display file needs correction Image Appears Squeezed or Vertically Stretched into Center of Screen CAUSE REMEDY Source data converted from film and pre squeezed for CP2000 XB s display format may require use of the auxiliary lens to regain full scope image width and proper proportions CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE Section 7 Troubleshooting 7 5 4 No Image Just Pink Snow CAUSE REMEDY l Make sure the projector s lid is not open In the event it is open close the lid an
95. R VV TINO a assests ancarescaiearecet re taepns sess E E 3 18 Can Alarm Conditions Be IOnorod somerson ori ner EEEE enters snetieuedenceeeee 3 18 oF LEPC ADOL M 110 e E E A A A E E E E 3 18 Understanding Versions in Your ProjeCiOT sirsenis em iiin orinar e a EEN Ean 3 19 Dee EPE CG OMe N a E EE A Gee totupncdeetaaieseeccaumanereanies 3 19 CSOT Pare N e E E E 3 20 Com Paine VICI ae E E E 3 22 Custom 3D Control MENU isisrersissrisreicserissiiveetoeienein ietan eirian in NaN RETAS ENa ania 3 23 Cuo a ICT a A E E E E E ET ES 3 26 Con TCs IVA aE E A OEE NOE EON OE OAE 3 27 Channel Lens Menu Disabled 2 icc cse csasessagssoannctsncnsaeesowsnedsanestagsdeanncdsncpeaedeeovsnedsauestagsdeanenssateess 3 28 Bie ETS Advan d MeD a E sas ateeaieee eteadonuieees oustouienes 3 28 Advanced Preicrence MENU ee ee 3 29 PN aC ENN ea EEN EA EE E TEE 3 30 Adine i New Lamp eneses ironion ana E E E SEEE EEES 3 31 Advanced Lamp THistory MONU sxc scsincacansiacustevetssanteimec asr E aE EEEO NO E 3 31 Advanced Lens Menu cnivsssmecesasdecsonissesedenedewadonesoasdesdssintddnesodssdiiesnesieduasbontaonesessdwabsneitonenededuesdeeid 3 32 Aae Te PEE ME a E E E 3 33 Advance d User MENI nergens an E E EE E EEEE 3 34 ee ee ad Bog 6000 ME E EE E E 3 36 A OIE S N N o E TEE E E EEE EE ER 3 36 Admin Screen Menu ccccccccssssssssecccccccceesssseecccccceeeaauenseesecceceeesaaaesseeecceceeesaaaasseeecceeeeseaaannees 3 39 CP2000 XB User Manual iii 020 100163 04 Rev 1
96. Red Gamma 44 Formatter Red Sequence 50 Formatter Green Boot 51 Formatter Green Main 52 Formatter Green Config 53 Formatter Green Gamma 54 Formatter Green Sequence 60 Formatter Blue Boot 61 Formatter Blue Main 62 Formatter Blue Config 63 Formatter Blue Gamma 64 Formatter Blue Sequence CP2000 XB User Manual B 21 020 100163 04 Rev 1 06 2009 Appendix B ASCII Messages If Pl 5 Self Test B 2 6 3D Controls TDC A number of 3D controls enable setup and adjustment of incoming 3D source material Parameter P1 activates the specific control and P2 sets the desired adjustment P1 P2 70 FFIB Main 71 FFIB Boot 72 FFIB FPGA Main 73 FFIB FPGA Boot 74 FFIB Startup FPGA 75 FFIB Satellite FPGA 76 FFIB Sequence Data 77 FFIB DMD Data 0 Interface Board 1 Processor Board 2 N A 3 System Supervisor Module SSM 4 ILS Motor Control 10 Space remaining on TPC IPSM KB 11 Space remaining on TPC Storage Card KB 12 Space remaining in TPC memory KB 0 Ok Non zero failed CHRISTIE For any test 0 OK 1 failed 2 Frame Rate Multiplication 3 L R Input Reference If L R input reference is 0 1 4 5 6 or 7 rare MNO ott We eee Tl p lt CGNro se 11 21 0 Use assigned GPI true polarity 1 Use assigned GPI inverted polarity 2 Left on Port A Right on Port B 3 Left on Port B Right on Port A 4
97. SC to B amp W TV frame rates Refer to 3 2 Pull down PULL DOWN LIST A selectable TPC menu item that unfolds into a list of options pertaining to it QUVIS A manufacturer of a digital video recorder player server QuBit frequently used for providing digital cinema data QuVis image compression uses a proprietary technology called Quality Priority Encoding based on wavelets in which the user selects a quality level based on signal to noise ratio The data rate varies to efficiently maintain that quality level Frames are coded individually REAR SCREEN A translucent panel for screen projection Incident light travels through the incident surface of a rear screen and forms an image on the other surface Rarely used for cinema applications A 10 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix A Glossary RELEASE PRINT Composite positive motion picture prints generally made from internegatives intended for distribution to exhibitors RESIZING The ability to manipulate the physical size placement and or aspect ratio of an image Also called scaling RESOLUTION The maximum number of pixels that the projector can display horizontally and vertically across an image such as 1280 x 1024 called SXGA or 2048 x 1080 RETRACE TIME HORIZONTAL The minimum time required for a CRT projector to move the position of the scanning spot from the right edge to the left edge RGB VIDEO The video output ana
98. T For connecting the projection head line cord to AC Upon plug in the projector is in a min imal power stand by mode e EXTRACTOR FAN and LED For connecting and monitoring the external extractor fan routed to the top vent on the projector The green LED indicates 220 VAC power is being supplied to the extractor out let CP2000 XB User Manual 3 3 020 100163 04 Rev 1 06 2009 3 4 Section 3 Operation CHix IS TIE l Exhaust Duct Connect the projector s 8 top exhaust hole to an outside vented duct with at least 10 of the last portion of the duct rigid at the projector The duct will also need a heat extractor providing the either 450 or 600 cf m airflow required of all models Refer to Section 2 Installation amp Setup Internal Connections e ETHERNET HUB All necessary components and links the TPC both Ethernet ports and the projec tor s internal processing hardware are factory connected to an internal multi port hub DVI PORTS Remove the access panel and connect a wide variety of non cinema video and graphics sources to either of these identical single link DVI ports NOTE These are single link ports for single link cable connectors only Using this pair of ports as a dual link pair requires a special adapter from Christie available early 2005 e RS232 B For connecting the Cine IPM 2K only e GPIO For connecting a wide range of external I O devices to the projector often so that an event on one devi
99. T O 2 oD i i i Image moved by a distance of 70 of half the image width NOTE Not possible with this projector Figure 2 15 Alternative Offset Specification 2 3 3 Floor Mounting and Leveling For front projection without suspending mount the projector on a strong supporting structure or cart Take special care if using a mobile cart avoid sudden stops force and uneven surfaces that may cause the top heavy cart to lurch and overturn Make sure your mounting structure is reasonably level then adjust one or more projector feet as necessary to fine tune Warning Do not invert this projector Adjusting the Feet For installations on a floor or suitable supporting structure a single projection head should rest firmly on its feet There is no need for the FredFrame unless stacking with another projector or unless you decide to rig and fly the projector To adjust the height and level of the projector extend or retract the feet by rotating them See Figure 2 16 Figure 2 16 Adjusting the Feet 2 12 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 2 Installation amp Setup 2 3 4 Tilting and Special Orientation Tilting In an ideal installation the lens surface is parallel to the screen This orientation helps to ensure optimized lens performance with minimal offse
100. TEP 10 Close Cooling Compartment and Lamp Door The projector will not operate unless the louvered door is locked shut STEP 11 Record the Lamp Installed With a blue dot label or dry erase pen mark the lamp door s LAMP INSTALLED label Figure 6 3 to indicate the size of the newly installed lamp 2 0 3 0 4 5 or 6 0 kW A supply of blue dot labels is secured inside the front cover of this manual A WARNING A LAMP SIZE setting in software LAMP INSTALLED must match LAMP INSTALLED 2kW 3kW 4 5 kW 6kW e Menu before power up e LCD shows LAMP SIZE setting LL Figure 6 3 Always Mark the Lamp Installed Label EXAMPLE STEP 12 Re Connect to AC and Turn Breaker to On Re connect the projection head and the ballast to AC refer to Section 2 1 Quick Setup then set the ballast breaker to ON STEP 13 Set the Proper Lamp Type Power and Record the Serial Number of the New Lamp Important Requires access to TPC Advanced Lamp menu If your new lamp is larger or smaller than the old lamp record the new lamp type 2 0 3 0 4 5 or 6 0 kW before igniting the new lamp This setting establishes the proper range of power available for the installed lamp ensuring that the new lamp is neither under powered nor over driven Warning Do not attempt to ignite the lamp until its type is correctly selected in the Advanced Lamp menu a In the Advanced Lamp menu select New Lamp b In the Lamp History submenu select the correc
101. TOR At the front of the projector install the auxiliary lens mount hardware as described in the instructions provided with Christie s Auxiliary Lens Mount Kit INSTALL THE 1 25x ANAMORPHIC or 1 26x WIDE CONVERTER LENS Clamp the 1 25x anamorphic or 1 26x Wide Converter lens mount in place following the instructions provided with the auxiliary lens mount kit Install First Lamp Nie 1 Protective gear required 2 Qualified service technician required Remove the lamp door and open the empty lamp cooling compartment Lamp Cooling Compartment Door Figure 2 20 Open Lamp Door and Cooling Compartment CP2000 XB User Manual 2 15 020 100163 04 Rev 1 06 2009 Section 2 Installation amp Setup CH IS TIE 2 4 3 Cooling 2 16 STEP 1 Check Lamp Cradle Anode End Location for Your Lamp The CP2000 XB accommodates different lamps Refer to Section 8 6 Lamps for a complete list of supported lamps e For 4 5 or 6 0 kW lamps the lamp cradle must be as far forward as possi ble factory default e For 2 0 or 3 0 kW lamps move the cradle to the rear position 1 e approximately 1 closer to the reflector See Figure 2 21 Reflector STEP 2 Install Lamp Refer to Section 6 4 Replacing the Lamp and Filter steps 7 11 Observe all warnings and wear protective clothing and shielding Lamp Cradle Don t forget to properly mark the Lamp Installed label on the lamp door to indicate curr
102. Valid IP addresses depend on the site ADR Which projector I P address is controlled by the TPC ADR 192 168 206 10 Projector 192 168 206 10 is controlled by the TPC Projector Configuration File PCF PCF TPC1 Use this pre defined projector configuration file PCF filename for processing This file contains TCGD CSC LUT AL LUT DG LUT CLUT and SOURCE information PCF What pre defined processing file is currently in effect PCF TPC1 The TPC1 pre defined proj configuration file is in use Projector Hours of Use PJH PJH The number of hours that the projector has been used incl standby and without a lamp How many hours have been logged on the projector PJH 5672 Maximum 16 777 215 hours Projector Rental Hours PRH PRH How long has the projector been running with the lamp on PRH 1251 Proj has run 1251 hours with the lamp on Pull Down Offset PDO requires v2 7 or higher PDO 2 0 field offset to 1 1 field offset to 2 2 field offset to 3 3 field offset to 4 4 field offset to 5 PDO Request field offset PDO 002 Response indicating field 3 offset CP2000 XB User Manual B 11 020 100163 04 Rev 1 06 2009 Appendix B ASCII Messages CH IS TIE l Function Code Examples Description and Parameters Pull Down Sequence PDS requires v2 7 or higher PDS 0 0 2 2 Pull down PDS 1 1 3 2 Pull down PDS Request current
103. a le l 1920x804 Scope Use PCF a ji Target Color Input jzcen sw pars Data Format Color Space 422 Unpacked 106t YCbCr 240M SOUrCE Gamma Adjust Color Space Gamma LUT CLUT Target Color amp Source if cleared e Always de select for cinema source e Always select to apply custom settings defined as a PCF using DCP Librarian Refresh Update Refresh all selection lists available in Custom menu we 30 Clear 1 or more channels Restore factory defaults i Applies custom color processing kd where choices are defined by installer Default P7V2 Theatre Type of color decoding such as Ed RGB or YCbCr p is20x804 2 39 Scope x Gamma 2 6 7 Type of gamma correction such as PL2 6 Page 1 350 Control Lamp Lens 15 19 41 Figure 3 9 Custom Page 1 Menu Creating Customer PCFs and Other Settings CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation USE CINEMA PROCESSING OR NOT The Cinema checkbox on the Custom Page 1 menu determines if the incoming signal is processed using the projector s full cinema path which enables image scaling and color correction but restricts resolution and frequency combinations If unchecked most of the projector s Processor Board functionality is by passed this disables scaling and color correction but is compatible with higher resolution and frequency combinations Generally use non cinema proce
104. able 1 1 Purchase Record on page 1 5 of this manual DLP or TPC Configuration Choose which address to see or change Projector name Not applicable for TPC Auto assign NOTE Requires a DHCP server Enter valid and unique address for this device and site Defaults shown NOTE Gateway is cur rently non functional SNMP Configuration Access SNMP con figuration options Choose which MIB structure to retrieve Trap Object ID from default 11273 Enter specific address to send trap information CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 Enables disables text entry below Figure 3 32 Choosing DLP or TCP from Admin IP Config Menu Enables disables text entry below Implement current settings Enables disables SNMP configuration 192 200 200 50 Figure 3 33 Choosing SNMP from Admin IP Config Menu 3 45 Section 3 Operation 3 46 Table 3 18 Summary of Admin IP Config Menu Options DLP vs TPC vs SNMP IP Address is sent ADMIN IP CONFIG MENU OPTIONS CHRISTIE Select which device address you wish to see or set DLP projector TPC Touch Panel Controller SNMP The Internet standard protocol developed to manage nodes servers workstations routers switches and hubs etc on an IP network SNMP enables network administrators to manage network performance find and solve network problems and plan for network growth Change Config Enter a
105. above determining the size of the area Leave offset at 0 default to process all incoming data or to zoom in at the center of the image Or set to a positive or negative value as described below Offset 0 7 pile e A positive x y value discards image data from top and or left e A negative x y value discards image data from bottom and or right Figure 3 25 Offset Differences ASPECT RATIO NOTES Table 3 15 lists the sixteen most common source setups which are selectable from the Main menu pages In the event your source material is pre scaled or compressed enter the desired aspect ratio Adding the 1 25x anamorphic or 1 26x Wide Converter lens will widen a squeezed image back to its original scope aspect ratio For sources that are not pre squeezed aspect ratio can be left at 0 Table 3 15 Pre configured Source Setups ADMIN SOURCE SETTINGS INCOMING ORIGINAL RESOLUTION ASPECT RATIO 1998 x 1080 1 85 flat 2048 x 858 2 39 scope Reserved PCF Flat flat 1920 x 1038 1 85 flat 1920 x 804 2 39 scope 1920 x 1038 1 85 flat 1920 x 818 2 35 scope Alternate Content 1 Auto square pixels 1920 x 1080 2 39 scope Alternate Content 2 Auto square pixels 1920 x 800 2 40 scope 3D Flat Auto square pixels 3D Scope Auto square pixels CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation Admin Screen Menu The Screen menu defin
106. ad all messages as strings of ASCII characters the actual message travels as a sequence of bytes Each character in a unicode message requires 2 bytes whereas the non unicode requires only 1 byte See example in Figure 3 40 which illustrates a picture mute is off reply from the projector NOTE Use of unicode or non unicode in messages is auto detected from the TPC ASCII L p L 2 0 0 0 NON UNICODE HEX 0x28 0x4c 0x28 0x21 0x00 0x28 0x00 0x4c 0x00 0x50 0x00 0x28 0x00 0x21 0x00 0x32 0x00 0x30 0x00 0x30 0x00 0x30 0x00 0x29 0x32 0x50 0x30 0x30 0x30 0x29 UNICODE HEX Figure 3 40 ASCII as Non Unicode and Unicode Available ASCII Codes All available ASCII message codes including those with multiple parameters are listed and explained in Appendix B Setup and Shutdown SETUP e In the Admin General menu define which users all none or some have remote access rights e Open an Ethernet socket to the TPC address socket 5000 By default the TPC address is 192 168 206 110 If you have additional TPCs the installer should have defined their addresses as 192 168 206 211 192 168 206 112 and so on or used other addresses that are valid for your site e Communication protocol should now be established and can be confirmed with a PNG if desired NOTE The socket will automatically close after 15 minutes of inact
107. ailed lamp fan Make sure the lamp door is securely shut Note that if the projector has been wired to the fire alarm at the site the Lamp Door alarm can indicate a fire alarm interlock failure Check auxiliary switch wiring Check for interference at vane switch Make sure the 220V connection near Panel C at the rear of the projector head on the underside is still plugged in Replace fan Failed heat extractor for external duct at the top of May not be turned on 600 CFM required Replacement heat extractor may be required the projector not turned on High current ballast cables not connected or ballast Check the DC cable connections at the ballast and projection head and make sure ballast is on Failed high security lock cinema use disabled Lock the projector lid If still failed double check the high security lock itself plus all 3 16 related harnessing Make sure a Type 3 interface board is installed and that you are using main software v10 0 30 or higher CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation OVER TEMPERATURE Card cage is too hot Power down and cool projector Ambient temperature may be too high Check air filter and fan Prism is too hot Power down and cool projector Reduce lamp power Ambient temperature may be too high Check air filter and sensor Check liquid cooler fan Integrator is too hot Power down and cool projector Reduce lamp power Ambient
108. akers staying on when enabled If they are tripping to OFF position there is an electrical problem requiring investigation by a certified electrician 7 2 Lamp 7 2 1 Lamp Does Not Ignite 1 Ifthe lamp button is entirely disabled not selectable at the TPC Main menu indicated by a red X on the lamp button there is an interlock failure such as an open lamp door failed lamp fan etc A flashing red alarm window also indicates this Refer back to solutions listed in Table 3 2 Alarm Conditions and Solutions on page 3 16 2 For SSM communication failures re boot and try again 3 Ifa DMD temperature is too high DMD over critical temp limit the lamp will not ignite Cool the projector and try again 4 Ifthe Status menu indicates a ballast communication problem re boot and try again 5 Ifthe lamp does not ignite after a second try replace the lamp 6 If there is no buzzing indicating that the igniter is attempting ignition there may be a problem with the igniter Christie service required 7 If there is a brief buzz attempting ignition but a lamp does not ignite the lamp likely needs to be replaced 7 2 2 Lamp Suddenly Goes Off 1 2 3 4 5 Try increasing the lamp power TPC Advanced Lamp menu The DMDs in the projection head may be overheated this also triggers an alarm window at the TPC An interlock may be interrupting lamp function Make sure the 220V connection near Panel C at the rear of the projector head on the undersi
109. al 020 100163 04 Rev 1 06 2009
110. al 100 vertical 70 horizontal 100 vertical 70 horizontal 100 vertical 70 horizontal 100 vertical 70 horizontal Primary Zoom Lenses Part Max of Image Below or Above High Brightness Lens Center 100 vertical 70 horizontal 100 vertical 70 horizontal 100 vertical 70 horizontal 100 vertical 70 horizontal 100 vertical 70 horizontal 100 vertical 70 horizontal 100 vertical 70 horizontal 100 vertical 70 horizontal 100 vertical 70 horizontal 100 vertical 70 horizontal 100 vertical 70 horizontal 8 2 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 8 Specifications 8 3 8 3 1 8 3 2 8 3 3 8 4 MAX OF IMAGE OFFSET kk OPT AUXILIARY LENSES PART FROMS LENS CENTER 1 25x Anamorphic 38 809054 51 n a determined by primary lens for 2 39 1 scope screen 1 26x Wide Converter 108 281101 01 n a determined by primary lens for 2 39 1 scope screen Maximum offsets are reduced when simultaneously offsetting horizontally and vertically Auxiliary lenses install in the auxiliary adapter optional and are used in conjunction with a primary lens Inputs Cinema Inputs Number of inputs 2 Standard supported SMPTE 292M bit serial Connector Type BNC NOTE Currently supported cinema formats are listed in Section 4 1 Compatible Cinema Sources Non Cinema DVI Inputs for Alternative
111. and make it square on the screen For best results avoid extreme tilts or offsets Corner vignettes on a white test pattern indicates extreme offset that should be avoided If you need more vertical offset range it is possible that the projector s mechanical TILT should be changed to help compensate for significant differences in screen and lens height cH 1 8 cH9 16 CH 17 24 CH 25 32 Lens 11 11 06 Figure 3 53 Intelligent Lens System 3 63 020 100163 04 Rev 1 06 2009 Section 3 Operation 3 9 2 CHRISTIE Zoom From the Main Lens menu click the zoom in out buttons to enlarge or shrink the image in each direction as necessary Focus From the Main Lens menu click the focus buttons as necessary for overall focus improvements For best results use a crosshatch test pattern or similar and focus on the center of the image 5 If the focus quality differs from edge to edge whether top bottom left or right the boresight of the lens mount likely needs correction Refer to Section 2 12 Offset and Boresight Alignment Figure 3 54 Focus Center of Image Auxiliary Lens NOTES 1 The auxiliary lens and its mounting structure are optional components 2 To install replace or use the auxiliary lens refer to the instructions included with the auxiliary lens mount kit To widen a squeezed image into a scope 2 39 1 theatre display swing the 1 25x anamorphic or 1 26x wide conv
112. and the surface of the screen are parallel to each other To adjust to the height and level of the projector extend or retract the feet by rotating them Refer to Figure 2 16 0 Offset oko 50 of image lens center 50 of image lens center Maximum amount of display 100 below or above center of of image lens 100 approx Figure 2 12 Vertical Offset Range NOTES 1 Assumes full 2048 x 1080 display 2 Recommended offset range can sometimes be exceeded however this may affect image quality 3 Due to manufacturing tolerances an offset range can vary 5 or more between lenses described as having the same throw ratio between projectors and with any lens projector combination 4 Simultaneous horizontal and vertical offset can limit the adjustment range of each as can long throw distances CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 2 Installation amp Setup Alternative Method of Describing Vertical Offset Offset can also be specified as the distance traveled from lens center such as 270 pixels and expressed as a percentage 270 pixels 50 of half of the image height This concept of image movement is illustrated in Figure 2 13 50 Offset Image moved by a distance of 50 of half the image height 75 of image lens center
113. are properly met in the current environment In the IP Config menu the administrator can define new Ethernet settings IP network addresses for the projection head and TPC e Installers and other service personnel can access two additional configuration menus General and Lamp as well as three more Status submenus Server Diag and Interrogator The installer can define system operating parameters such as which projector is controlled by the TPC and critical lamp parame ters such as installed lamp type fan speed and light level at the screen Installers can also establish temper ature scale preference remote access rights test pattern access rights and extent of data logging An installer can see ID and error information for servers as well as a detailed diagnostics log for in depth trou bleshooting TPC Power Up Defaults When the CP2000 XB powers up the Touch Panel Controller will begin the steps of Initializing Attempting to log on and Updating status displaying its progress on the TPC status bar at the bottom of the screen When initializing is complete all files are refreshed on the TPC and the system is in a ready to use default operating mode e The Main menu appears on the Touch Panel Controller where you can press the lamp button to turn on the lamp e The most recently used channel button is depressed darkened Upon turning on the lamp the image will appear Failed TPC Connection If the TPC fails to initia
114. ation amp Setup CONNECT TO POWER Connect the line cord of the extractor fan to the Extractor Fan outlet on the rear panel of the projector Use appropriate extension cords if necessary The fan will power up with the projection head and will run for a 10 minute cool down period after the projection head is powered off This ensures proper lamp cooling CALCULATE CFM IN 8 DUCT Use an air flow meter to measure the ft min or ft sec where the duct connects to the projector measure at this end only Then multiply the reading by the cross sectional area of the 8 duct 0 34 to calculate the cubic feet min airflow The formula is Measured linear ft min x 0 34 CFM NOTE f the duct becomes significantly blocked or if a fan fails the projector should trigger an error message before becoming overheated or unsafe Regardless check airflow regularly Ni e Never disable a vane switch Attempting to operate the projector without monitoring airflow can result in dangerous overheating of the projector Figure 2 26 Vane Switch Side Venting Duct Adapter All stacks require a special side venting duct adapter between projectors otherwise the top projector blocks exhaust from the top of the bottom projector This Side Venting Exhaust Adapter Kit 1s required on any bottom projector used in an upright stack of two Liquid Cooling During operation a closed loop of flexible tubing circulates liquid coolant from a small res
115. ator 20 Temperature SSM 21 Temperature Card Cage 22 Temperature Ballast 23 ILS over temperature 32 Lamp Life Expired 33 Lamp Failed to Strike 35 Lamp Unexpected Lamp OFF 36 Lamp Reading Lamp Intensity Failed 48 SSM Communication Error 48 SSM Upgrade Failed 68 I2C Communication Error 96 ILS Communications Error 97 ILS Sensor Failure 98 ILS In Bootloader 99 ILS CRC failure on main code B 4 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE Function Code Examples Focus FCS requires v2 9 or higher FCS 860 FCS 860 1 FCS 860 1 1 For Your Information FYI FYI Gamma GAM GAM gamma2 6 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 Appendix B ASCII Messages Description and Parameters Used to adjust the focus under motor control Write P1 Location P2 Approach direction NOTE Approach is optional 1 Positive to Negative Approach 1 Negative to Position Approach Read P1 Real time position P2 Current direction P3 Moving Status 0 not moving 1 moving Related commands are Intelligent Lens System ILS Lens Horizontal Offset LHO Lens Vertical Offset LVO and Zoom ZOM A change in projector status generally broadcast from TPC proj to all clients See Messages With Multiple Parameters in this Appendix The filename representing the current gamma For example
116. ature 10 C to 35 C 50 F to 95 F Humidity non condensing 20 to 80 Altitude 0 3000 meters Non Operating Environment Temperature 25C to 65 C 13 F to 149 F Humidity non condensing 0 to 95 Weight and Size NOTES 1 Excludes lens cabling extractor 2 All weights subject to change Shipping Weights 360 Ib 163 kg 145 Ib 66 kg 153 Ib 70kg Installed Weight 260 Ib 118 kg 110 Ib 50 kg 105 Ib 48 kg Refer to page 8 7 Standard Dimensions W x L x H 25 6 x 49 0 x 20 65 cm x 124 5 cm x 50 8 cm Size with Anamorph W x L x H 25 6 x 64 6 x 20 65 cm x 164 1 cm x 50 8 cm incl auxiliary lens mount and lens CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 Section 8 Specifications CHRISTIE SUO SUSBUIIG X 0002d9 L s a4nbig SHALNAD LOOA SN31 XVIN NII _ a88 a LPE 8L _ gt 8 7 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 Section 8 Specifications 8 10 Standard Components 8 8 Projection Head includes Line cord Touch Panel Controller with mounting hardware and 3 ft cable Security keys for lamp and igniter service access plus assorted Al
117. ballast s internal fan indicates whether or not the breaker switch is on There is no other indicator Lights on the ballast indicate only that the ballast is plugged in CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation U Channels for FredFrame Christie s FredFrame inserts and secures at these U channels under the projector enabling the projector to be safely hoisted flown and or stacked with another unit Consult complete instructions supplied with the frame kit Communications and Source Connection Panel This connection panel links the projection head to its other tethered components namely the TPC remote lamp ballast and extractor fan and to all external devices except non cinema DVI sources and devices routed via GPIO e CATHODE ANODE CONNECTORS For connecting the bal last s 2 lamp cables both DC Note that cable length must be defined in the projector e BALLAST INTERLOCKS For connecting the safety interlock signals and the Lamp Enable signal between the ballast and the projection head RS232 e BALLAST CONTROL For connecting the RS232 control signals between the ballast and the projec tion head enabling the projection head to dictate the amount of current or power to be supplied from the ballast to the projection head e RS232 For serial communications to and from RS232 compatible equipment such as a PC or other controller Not for loo
118. bration must be done with new lamp change Admin GPIO Menu Use the Admin GPIO menu to configure GPI macros for LAMP ON OFF DOUSER OPEN CLOSE and AUXILIARY LENS IN OUT and also GPO macros for LAMP STATE DOUSER STATE AUXILIARY LENS STATE and SYSTEM HEALTH STATUS NOTES 1 Only GPIO 1 5 can be programmed 2 Use of GPIO for 3D will automatically un program any other use for that pin GPI macro name Ext GFI 1 Falling Edge r Panna Jautensin v GPO Macro name k GFP 1 Predefined redefined macro Douser Stake kd IF Config GPIO Figure 3 37 Admin GPIO Menu Options CP2000 XB User Manual 3 49 020 100163 04 Rev 1 06 2009 Section 3 Operation CHA IS TIE l 3 5 8 Selecting a Display Starting a Presentation NOTES 1 For manual operation i e non automated 2 In order to use the TPC software originally shipped with the projector the installer typically connects a laptop and uses Christies DCP Librarian setup software to download all necessary configuration files to the projector for use at the TPC To change to a new source i e a new presentation or display do the following e Make sure the CP2000 XB and TPC are both powered up and operating normally e On the Touch Panel Controller TPC select the Main menu tab e On the Main menu select the desired channel button the image will update accordingly NOTES 1 Depending on your expected needs your installer may or may not have configured all eight buttons
119. by adjusting the Vertical Boresight accordingly 0 Figure 2 40 Adjust Vertical Boresight 5 When both sides appear equally blurry adjust the Offset by clicking the up down left right buttons on the Main Lens menu to re center the image on the screen Repeat Steps 2 5 until the top and bottom of the screen are both well focused 7 Refocus Although all sides of the image should now be in focus the center of the image may be slightly blurry at this point Re focus the center of the image The goal is for good focus at the center and on all sides 8 Adjust the Vertical Hold Screw to lock the lens mount in place Check boresight again See Figure 2 40 For more information on ILS and channel setups refer to Section Custom Lens Menu on page 3 27 2 12 4 Copy the Channel Settings To Another Channel Main Status Custom advanced Admin about Diag Once the basic image alignment for a channel is complete you can copy this setting between channels e From the Custom Lens menu use the drop down menu to select a particular channel and click Copy for the changes to affect the Copy Lens Settings To Channel selected channel Repeat for every channel that requires the same for 1998x1080 Paez ILS values Page 1 Page 2 30 Control Lamp Lens 11 11 06 Figure 2 41 Copy Channel Settings 2 28 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 2 Installation amp
120. ce automatically triggers an event on the other Currently only inputs outputs for 3D devices can be defined in projector software Lamp Any CP2000 XB lamp 2 3 4 5 or 6 kW can be used with the universal 7 kW ballast The lamp door must remain closed and locked for all normal operation Trained operators only can access the lamp via security key Refer to the complete lamp specifications in Section 8 Specifications Lens Mount and Auxiliary Lens Mount The lens mount secures and seals a primary high contrast zoom cinema lens within the projector and provides manual adjustment of focus zoom and offset Adjacent to the primary mount an optional auxiliary lens mount may be added providing a mechanism for positioning a 1 25x anamorphic or 1 26x Wide Converter lens in front of the primary lens Such a lens horizontally spreads a pre squeezed image back into its wider 2 39 1 scope image and is most typically used in side masking theatres Leveling Feet For most cinema installations the projector is inclined slightly forward to match screen tilt and to minimize the amount of vertical offset required Turn the adjustable feet to increase or decrease projector height as needed for proper leveling and or slight tilt Refer to Section 2 3 Projector Position and Mounting Liquid Coolant Use the Christie approved coolant Jeffcool E105 provided in the liquid coolant fill service kit P N 003 001837 02 to fill slightly more than half of the
121. characterized by unusually thin people Display pixels are then stretched horizontally through the auxiliary lens so that the full 2 39 image width appears on screen The image becomes wider but not taller See Figure 4 3 gt Compressedil lt Normal Scope Image oe ee CHAISTIER O CHKISTIE Unused saoo o screen Gage Figure 4 3 Typical Method for Achieving Scope If the incoming material is not pre squeezed by the distributor you can squeeze it on site by using a source file in which the combined settings for 1 incoming source resolution and 2 desired aspect ratio define the necessary compression The incoming material will then be squeezed into a narrower area on the projector s DMD panels with the final aspect ratio setting determining the actual degree of compression Refer to Section 3 5 Using the Touch Panel Controller for more information about choosing Source menu settings Theatre Variables Masking In order to present either type of feature on a single screen a Cee theatre typically uses masking to conceal any unused edge s of the screen These movable panels or curtains are most commonly installed along the top edge of the screen changing siege the height of the screen but not its width The screen shown in Figure 4 4 at right also has a bottom mask Top bottom masking to hide screen edges e Add masks for scope Open masks for flat Masking moved aside
122. checkmark to edit the Ethernet Configuration text boxes defining the device s address Enter a name for the projector optional Allow the projector s IP address to be auto assigned by your network s DHCP server NOTE Cur Obtain address from DHCP rently not supported Specify a Static IP Enter the full valid and unique address supplied by the network administrator for using the device at Address this site When DLP or TPC selected The first three octets of the IP address identify the network to which the device belongs the last octet identifies the specific device 1 e the projector or the TPC Keep in mind that if you change the node any of the first 3 octets the device will then belong to a different network and will not interact until the other device is also changed accordingly When SNMP selected Enter specific IP address where trap information device status notification i e fan failure Subnet Mask All IP Addresses for a network belong to the same Subnet Mask as defined by the network adminis trator Default Gateway Not used All entries are ignored Apply Implement your current Ethernet Configuration settings Trap OID Retrieve information on the condition of a device from a specific MIB Management Information Base structure Default old MIB structure 11273 new structure 25766 Changes in the IP Config menu automatically change the projector IP address appearing in the Admin General menu which identi
123. cing the Air Filter 5 Filter installed ual 020 100163 04 Rev 1 06 2009 CP2000 XB User Man 6 12 CH IS TIE i Section 6 Maintenance 6 5 Replacing a Lens A variety of primary lenses can accommodate different throw distances and specific types of installations refer to Section 8 Specifications To replace or change a lens 1 Release the lens locking lever UP position 2 Pull out lens and replace with a different primary lens as described in Section 2 4 Installing a Lens Lamp and Cooling Secure with lens locking lever down position 4 Calibrate the lens See Section 2 10 Basic Image Alignment for details CP2000 XB User Manual 6 13 020 100163 04 Rev 1 06 2009 CHRISTIE 7 Troubleshooting If the projector does not appear to be operating properly note the symptoms present and use the following guide to assist you If you cannot resolve the problems yourself contact your dealer for assistance NOTE 4 qualified service technician is required when opening an enclosure to diagnose any probable cause e 7 1 Power e 7 2 Lamp e 7 3 TPC 7 4 Ethernet e 7 5 Cinema Displays e 7 6 Non Cinema Displays CP2000 XB User Manual 7 1 020 100163 04 Rev 1 06 2009 Section 7 Troubleshooting CH IS TIE 7 141 Power 7 1 1 Projector Will Not Start 1 Check for green Main AC light on projector If not on check all breakers on projector and at the wall There are single phase and 3 phase 2 Are the CP bre
124. cluding parameters that allow the program to be tailored for a specific venue or engagement A show script is created by the exhibitor or installer and provides automated presentations Automation available 2005 SOURCE The device such as a server connected to the projector for supplying incoming data SOURCE SETUP Refer to Channel SWITCHER A signal selector specifically the Marquee Signal Switcher formerly manufactured by Christie can be connected for adding more sources to a projector SYNC The part of the video signal that stabilizes the picture Sync can occur in three forms 1 Composite sync the horizontal and vertical components are together on one cable 2 Sync on green the sync is part of the green video 3 Separate syne or H SYNC and V SYNC the horizontal and vertical components of the sync are on two separate cables SYNC WIDTH The duration of each sync pulse generated by a computer The sync width is part of the blanking time TTL VIDEO A type of RGB video with digital characteristics TAMPER INTERLOCK A switch that detects when the light engine compartment is unlocked It is monitored by the electronics to log accesses If activated encrypted playback such as cinema presentations for example will be interrupted TERMINATED A wire connecting a single video source to a display device such as a projector must be terminated by a resistance usually 75Q for video THROW DISTANCE The distance between the
125. color space target color gamut source aspect ratio resolution and gamma a k a degamma settings for a cinema or non cinema source Once the collected settings are downloaded to the projector s internal memory their PCF can be assigned to the corresponding CP2000 XB input connection and quickly applied via a controller such as Christie s Touch Panel Controller No further adjustment in processing should be required Refer to the DCP Librarian User s Manual for all DCP Librarian Setup Software operating details and procedures CP2000 XB User Manual 2 31 020 100163 04 Rev 1 06 2009 CHRISTIE 3 Operation This section describes how to use the projector once it is properly installed by a qualified service technician as described in Section 2 Installation amp Setup NOTE The illustrations provided are to enhance the understanding of the written material and may not represent your exact projector model e 3 1 Projector Basics e 3 2 Power Up Procedure 3 3 Power Down Procedure 3 4 Introduction to the Touch Panel Controller 3 5 Using the Touch Panel Controller 3 6 Remote Control of the Touch Panel Controller e 3 7 Upgrading SSM Firmware 3 8 Working with the Lamp 3 9 Working with the Lens 3 10 Working with 3D 3 11 Working with Servers and Diagnostics CP2000 XB User Manual 3 1 020 100163 04 Rev 1 06 2009 Section 3 Operation CHA IS TIE l 3 1 Projector Basics 3 1 1 Components Features
126. d Screw Horizontal Boresight Bolt Figure 2 36 Horizontal Boresight Adjust the Focus to retract the lens using the down arrow on the Main Lens menu See Figure 2 37 Watch the image at the left edge of the screen until it comes into focus If the image appears well focused on the left edge but not on the right determine if the right side focuses in front of or behind the screen If the entire screen come into focus skip to step 7 Status Custom Advanced Admin About Diag A gt g a E a spam gt lens Reset Hialonsie cre H2592 tens Figure 2 37 Adjust Focus Continue retracting the lens a Ifthe right side of the image comes into focus before the lens is completely retracted then the image focuses in front of the screen See Figure 2 38 To correct this problem adjust the Horizontal Boresight bolt to direct or aim the lens mount towards the LEFT to balance out the left right edges See Figure 2 36 b Ifthe right side of the image fails to come into focus then the image focuses behind the screen To correct this prob lem direct the lens mount towards the RIGHT by adjusting the Horizontal Boresight accordingly When both sides appear equally blurry adjust the Offset by Focus Left Edge Center AERIAL VIEW Screen Surface Focused Projector Figure 2 38 Aerial View Illustrating Misaligned Boresight clicking the up down left right buttons on the Main L
127. d depends entirely on the original source mastering L R Display Reference Always Not Used unless a separate 3D stereo sync input is at GPIO connector See L R Display Refer ence Notes below L R Output Polarity Keeps 3D stereo sync output the same as input true or reversed inverted See L R Output Polarity Notes below Frame Rate Ratio of total frames displayed to frames forming complete data Increase to reduce flicker in dis plays lt 96 Hz Max recommended setting for 2048 x 1080 displays 5 2 Can be higher in smaller displays or decreased if incoming signal is already high enough to prevent flicker See Frame Rate Notes below Input GPI Select None when 3D stereo sync input is part of source signal at ports A and B Use GPI 1 7 only if sync input is supplied to GPIO port Display GPI Always None unless 3D stereo sync input is at GPIO connector Output GPO Define your GPO sync output for 3D device glasses or z screen polarization using to 1 7 depending on wiring CP2000 XB User Manual 3 23 020 100163 04 Rev 1 06 2009 Section 3 Operation CHA IS TIE l 3 24 CUSTOM 3D CONTROL MENU OPTIONS Dark Time Adj Create a blank time interval between L R frames to allow for glasses ON OFF Helps synchronize the output to the viewing Output Delay Time Offset in u 3D stereo sync output in relation to dark time interval Positive offset delay negative offset start early See Output Delay Notes below L R
128. d pause or stop the show on the server Then press play on the server and wait several seconds for the projector to receive the set of decryption keys from the server If after 30 seconds the projector doesn t recover pause or stop the show and try playing again If this doesn t work try resetting the server Make sure the IP octets for the projector and the server Eth1 port match CineCanvas does not have the correct projector IP address Check the IP address of the projector and server and change if necessary They should match 7 6 Non Cinema Displays The following troubleshooting entries assume that you are using a 3 d_party input source for displaying alternative non cinema material As a first step always consult the documentation supplied with the external equipment 7 6 1 The Projector is On but There s No Display CAUSE REMEDY 1 Was a lens cover accidentally left on Remove lens cover 2 Make sure the douser is OPEN 3 Is the lamp ignited Press the lamp button on the Touch Panel Controller 4 Is the correct DVI channel button selected on the Touch Panel Controller 5 Is AC power connected 6 Is an active source connected properly Check the cable connections and make sure the alternative source 7 is selected Can you access test patterns If so check your source connections again 7 6 2 The Display is Jittery or Unstable CAUSE REMEDY l If the non cinema display is jittery or blinking erra
129. d when there is no more room An accurate lamp history requires that the serial for a new lamp be recorded when the lamp is installed HIS message parameters are P1 Lamp order oldest lamp installed 001 next oldest 002 etc P2 of hours logged P3 Lamp serial P4 strikes P5 Installation date amp time P6 Lamp type P7 Status Failed to Strike P8 Status Failed Restrike P9 Status Unexpected Off P10 Life State P11 Change Reason B 2 4 Intelligent Lens System ILS B 18 0 Installed 1 Lens Reset on Startup 2 Auto ILS 3 Lens Calibrate 4 Lens Reset 10 Move All Motors NOTE This command should be used to move all motors at the same time It is more efficient then using LHO Lens Horizontal Offset LVO Lens Vertical Offset FCS Focus and ZOM Zoom 0 No 1 Yes 0 No 1 Yes 0 No 1 Yes None None P2 X location P3 Y location P4 Focus location P5 Zoom location P6 X approach P7 Y approach P8 Focus approach P9 Zoom approach NOTE Approach is optional When no approach is specified a Negative to Positive Approach is assumed 1 Positive to Negative Approach 1 Negative to Positive Approach CHRISTIE Return Value 0 No 1 Yes 0 No 1 Yes 0 No 1 Yes 0 Complete non zero indicates In Progress 0 Complete non zero indicates In Progress This is write onl
130. de is still plugged in Replace the lamp 7 2 3 No Lamp Current Reading With this communication error the lamp will be powered by the last lamp power setting in effect 7 2 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE Section 7 Troubleshooting 7 2 4 Flicker Shadows or Dimness 7 2 5 7 2 6 tS LampLOC may need re adjustment LampLOC may be in the middle of its adjustment Wait approximately 2 min Increase lamp power if possible Determine if it is mid level grayscale flicker beating adjust 3 phase balancing for minimized ripple requires qualified service technician LampLOC Does Not Seem to Work l In the TPC Advanced Lamp menu try adjusting lamp position using one button at a time watch light level for changes indicating lamp movement If the motors do not respond via any TPC buttons you can position the lamp manually within the projection head UV danger Qualified service technician only LiteLOC Does Not Seem to Work Make sure LiteLOC is set and enabled in the Advanced Lamp menu 2 Changing the Lamp Power setting disables LiteLOC 3 Ifthe lamp power has increased to its maximum in order to maintain a LiteLOC setting LiteLOC 1s automatically terminated If the values shown in the Advanced Lamp menu indicate that the lamp power has reached this over drive state either reduce your LiteLOC setting or install a new lamp 7 3 TPC 1 Ifth
131. ding to the pins wired in the GPIO cable refer to Figure C 1 For instance if you have wired pins 10 and 29 to your 3D device set Output GPOto GPO 2 C 4 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE Appendix D Repacking the Projector If you need to relocate or ship the CP2000 XB repack the projection head with the original packing materials used for shipping NOTE The illustrations provided are to enhance the understanding of the written material They are graphical representations only and may not represent your exact projector model CP2000 XB User Manual D 1 020 100163 04 Rev 1 06 2009 Appendix D Repackaging the Projector CH IS TIE l Detail A K Cardboard Lid with Foam Clearance for foot Cardboard Sleeve Projection Foot Brace Plastic Base Retaining Plates 4 Pallet 3 Pre installed on pallet Figure D 1 Packing the Projection Head 1 Set the plastic base on the pallet Set foot braces aside 2 Extend feet to clear the bottom of the projector by approximately 1 inch or more 3 Place the projection head on the plastic base with lens nearest the larger front area as shown in Figure D 1 4 Lift projection head slightly and slide in foot braces fully to nearest stop 5 Align feet to braces Detail A and secure braces with bolts at retaining plates 6 Add remaining packaging sleeve and foam lined lid Strap all together D2 CP2000 XB User Manu
132. e 2 5 Installing and Connecting Sources e 2 6 Connecting for Communications e 2 7 Connecting the Ballast e 2 8 Initial Power Up e 2 9 Maximizing Light Output e 2 10 Basic Image Alignment e 2 11 Basic Optical Alignment Procedure e 2 12 Offset and Boresight Alignment e 2 13 Fold Mirror and Convergence Adjustment e 2 14 Calibrating the CP2000 XB System CP2000 XB User Manual 2 1 020 100163 04 Rev 1 06 2009 Section 2 Installation amp Setup CH IS TIE 2 1 2 2 Quick Setup Follow these steps for quick setup of the projector in a basic front mount position STEP 1 Position the Projection Head Locate the projection head at an appropriate throw distance projector to screen distance and vertical position Refer to Section 2 3 Projector Position and Mounting Make sure that the projector is level from side to side and do not invert Locate the lamp ballast so that its 4 cables can reach the rear of the projection head STEP 2 Install the Touch Panel Controller TPC Attach the Touch Panel Controller pre assembled with its ball joint base and mounting arm to the matching ball joint base secured at the rear of the projector Plug the TPC into the TPC port on the projector s rear connector panel using the standard 3 ft cable provided ouch Pa Ney K Controller Alternatively mount the TPC in a remote location up to 50 feet l Ns ons away and attach to the rear of the projector using the optional R S i long
133. e KD sch E A E E ones E SAE unease 4 4 4 3 SClecting the C mema SOULCE exccsvasensustivesnieescoussebbnaiansdantwiuekivasaserseevinehbachansuantainchiwhonestdwebennedateiwehhoass 4 6 e Eo ee 2 COI E E E E E E teams ausumeaveene 4 6 JL TINE N CN eea a es A E 4 7 AA PG St He Cinema Display ecseri i i n iiri 4 7 5 Non Cinema Operation 5 Compatible Non Cinema SOUL CS eissits iraa aE EE E E E EE ESIS 5 2 EFD kann NL R DY e r E O EA T 5 3 D2 CCC ae OE a E EE A E R 5 3 6 Maintenance AE a E E Saat ccc EE A E E A eae meeeese 6 2 6 1 1 Labels and Markings ccccccccccccccee cece ee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeEEEEEEEEEEEEEE EERE EERE EH 6 2 of EG oialci eM eiecrer A ee ee T 6 2 GLAC TONT he CA IOING a E E EO 6 3 AR E E 0 0 1c E E EA A A E A E T EE 6 3 Woar TOU CUS LO CMI pr r AE AEE AEE O E 6 3 Cool the Lamp Completely cccccsssessssseseessessesessesseesseeeeeeeeeeeeeeeeseeseseeeseseeseeeeeeeeeeeeeeeens 6 3 o N TOT COO O a TE N E T NEE N een ene 6 4 eS TO E E E E E E A EE T AE 6 4 OLLA T a EE E A E E 6 4 6 2 3 Exhaust Duct and Lamp Fan Interlocks eeeseeeeeessesssssssssreeeseecrrcrereessssssssssssseeceeceeeeeesssssssssss 6 4 6 3 M intenance and Cleaning occa sitse aac ox crc nsacncacesoadsusadanososwaesvsoaesarseusaaeasioas sar yoseaetouscsarseoieaneauaeceioauoe 6 5 oh EE CI a cipcs reins sates nse terse tor gece are E psionic eda sas best a E 6 5 DZ IS EE E E te attatoes aan gas E onsen dva E TT E E T
134. e Letterbox Notes below Lens Factor Define the auxiliary lens needed 1 25 for the CP2000 series to stretch an image horizontally Leave at 1 default if no auxiliary lens is needed Slidebars Adjust coordinates for presentation area and or cropping as desired Create Screen Save current presentation cropping lens factor and auxiliary factor settings as a Screen file accessed and applied from within the Custom menu Cancel new unsaved screen settings Test Apply current settings to the image without saving CP2000 XB User Manual 3 39 020 100163 04 Rev 1 06 2009 3 40 Section 3 Operation CHA IS TIE l PRESENTATION NOTES Presentation points define what region of the projector s available display area responds to incoming data By default the projector will use its complete display area scaling the incoming data as necessary If for some reason you want to limit the display area enter the desired upper left and lower right Presentation coordinates or adjust with slidebars You can define a smaller rectangular area in which the left and right top corners will always share the same y coordinate as will the left and right bottom corners and the top and bottom left corners will share the same x coordinate as will the top and bottom right corners Thus upper right and lower left coordinates are not available to define the area Incoming data will then automatically resize to fill the reduced rectangular area d
135. e TPC fails to initialize re boot the projector and try again 2 A failed TPC usually indicates a system failure requiring service 3 A TPC communication failure crash while displaying a test pattern requires that the projector be cycled OFF and ON again 4 Ifthe TPC response becomes sluggish try re booting the projector If it persists the installer may have set the TPC Data Logging option to Detailed which taxes memory and performance For best results and normal operation this setting should be reduced to Errors or Standard 5 Erratic TPC behavior or an error message such as Could not write to file can also indicate an internal memory shortage Make sure to regularly delete back up files or corrupt files from the IPSM and or Compact Flash memory card Save backups to a PC laptop only not the TPC contact your administra tor 6 Ifthe locations of button presses on the screen seem to be misinterpreted the TPC screen may need recalibrating CP2000 XB User Manual 7 3 020 100163 04 Rev 1 06 2009 Section 7 Troubleshooting CH IS TIE 7 4 7 5 7 5 1 7 9 2 7 5 3 7 4 Ethernet 1 Ifthe TPC stalls at Waiting to Connect you have 30 seconds in which to enter a service login Make sure the Ethernet settings are valid for your site all devices should have the same subnet mask but unique IP addresses 2 Be sure to save any address changes and re boot to implement all changes 3 IP address shown in T
136. e design with familiar menu icons enables a novice user to display an accurate and fully optimized image by pressing a single button on the touch screen while protecting precisely configured presentations from accidental or unauthorized change CP2000 XB User Manual 3 7 020 100163 04 Rev 1 06 2009 Section 3 Operation CHA IS TIE l 3 4 1 3 4 2 3 8 TRAINED OPERATORS ADVANCED USERS ADMINISTRATORS and INSTALLERS In addition to the basic user rights shown in the Any User above the TPC offers four distinct password protected levels of use shown in shaded areas in Figure 3 2 Each has all of the rights of lower levels plus additional rights as described below e Trained Operators can also access the New Lamp function required when replacing the lamp e Advanced users can access two additional menus Custom and Advanced where they can define all dis play setups and set the DVI processing path configure 3D displays optimize light output record lamp changes activate test patterns and set certain system preferences e Administrators can also use four Admin submenus Source Screen color Gamut and IP Config to define setup files as selectable choices for processing a variety of incoming signals Source files set incoming resolution offset rare and desired final aspect ratio Screen files determine image cropping masking size of display area and type of lens and color Gamut information ensures color display stan dards
137. e function you wish to work with such as channel switching or picture mute is represented by a three character ASCII code A Z upper or lower case This function code appears immediately after the leading that starts the message REQUEST REPLY SYMBOL If the controller is requesting information from the projector a question mark appears directly after the function code If the projector is replying an exclamation mark appears directly after the function code For set messages neither of these characters appear the code is followed by the data itself see next paragraph CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation DATA The value for a given projector parameter such as on or off appears in ASCII decimal format directly after the request reply symbol Unless you add an optional space after the symbol 1 e before the data in a set message data immediately follows the request reply symbol without a space Other details about data e All values returned by the projector reply messages have a fixed length of either 3 or 5 characters regardless of the actual value the value is padded with leading zeros as needed e Data in set messages does not require padding e For any given parameter data length is always the same E g the picture mute value which is either on 1 or off 0 is always 3 digits 001 or 000 e Within one message multiple parameters of data must be se
138. e option list in Section 8 Specifications 1 2 2 Software Requirements DLP version 14 series or higher TPC version 2 9 or higher 1 4 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE i Section 1 Introduction 1 3 Purchase Record and Service Contacts Whether the projector is under warranty or the warranty has expired Christie s extensive and highly trained factory and dealer service network is always available to quickly diagnose and correct projector malfunctions Complete service manuals and updates are available to service technicians for all projectors Should you encounter a problem with any part of the projector and require assistance contact your dealer or one of the Christie service depots listed on the back cover of this manual In most cases CP servicing is performed on site If you have purchased the projector fill out the information on the following page and keep with your records Table 1 1 Purchase Record C DeserPhoneNunbe Projecten tead soanar fT a C Table 1 2 Ethernet Settings for This Projector The following Ethernet settings were defined during installation of the CP2000 XB and its Touch Panel Controller Default Gateway DNS Server CP2000 XB Projector Address Projector 1 4 Who Should Use This Manual USERS OPERATORS This manual is intended for trained users authorized to operate professional high brightness projection systems located in restricted areas such as projection rooms in t
139. e side or the other of the lens 2 Maximum offsets are slightly less when offsetting in both directions H and V at once 0 Offset NO OFFSET 50 of image lens center 50 of image lens center Maximum amount of display below or above center of lens 100 approx Figure 2 35 Vertical Offset Range CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE 2 12 2 Adjust Left Right Boresight The goal for left right boresight alignment is to adjust the lens mount until both sides of the image focus on the screen simultaneously Projectors are aligned properly at the factory but due to mechanical tolerances in the alignment between the projector and the screen the left and right sides of the image come into focus at different times By focusing on the left side of the screen we need to determine if the right side of the image focuses in front or behind the screen relative to the left side NOTE Use a test pattern with a single pixel vertical and horizontal line and perimeter frame such as DC2K Framing or RGB Alignment l The Horizontal Hold Screw acts as counter resistance to hold the lens mount in place once set Before adjusting the boresight loosen the Horizontal Hold Screw See Figure 2 36 Extend the lens completely Section 2 Installation amp Setup Horizontal Hol
140. e standard frame rate for most 2D cinema content is 24 frames per second FPS as it is for film For 3D the server splits the 3D content video signal into 2 interleaved signals of 24 FPS each by the server for a total input of 48 FPS into the projector The projector s frame rate multiplication is set to 6 2 meaning the input frame is multiplied by 3 Triple for a total frame rate of 144 frames per second Hz or FPS For the Brilliant3D hardware the TI DLP version 13 1 or higher is required CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation 3 10 2 What Do I Need for 3D The CP2000 XB requires a 3D capable SMPTE source and a few special hardware software setups described below Essentially you will connect two signals one left eye one right eye to the projector then use the TPC s Custom 3D Control menu options to define and control the signal processing synchronizing and output for devices used in your stereographic 3D display These settings ensure critical ordering and timing of the incoming L R frames so that they merge correctly into a convincing artifact free 3D display without cross talk ghosting or other artifacts System Requirements e CP2000 XB projector Includes all standard 3D components e FFIB FPGA Formatter Interface Board e TPC software v2 3c or higher e Main projector software v8 0 or higher Two HD SDI cinema signals left and right connected to the projector s SMPTE
141. eLOC The current brightness level will be maintained as long as possible NOTE Arbitrary units shown here not footlamberts or lumens CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation Custom Lens Menu This menu is used to modify the Intelligent Lens System settings for a particular channel Adjust the Focus Horizontal X and Vertical Y Offset or Zoom by clicking the respective buttons in a step wise manner or holding the button down for continuous movement You may experience a slight delay in the response rate of the lens upon selecting the buttons Position values on the menu will change in real time When holding down a button for continuous movement the lens will begin to accelerate until the maximum velocity is reached NOTES 1 Using the Emergency Override knobs on the lens mount are designed for temporary emergency use therefore hone reference settings will be lost once the channel changes 2 This menu is for advanced users only 3 Keep clear of rotating parts Remotely operated motors may start to spin without warning 4 Avoid long hair jewelry and loose clothing exposure to the knobs during manual adjustment 5 In case of emergency unplug the line cord to immediately halt movement of the lens mount ANUS Tite 1 If the Motorized Auxiliary Lens Mount MALM is present ensure to move the MALM to the OUT position before performing any lens calibrate or reset functions on the Motori
142. ec essa ap esc tees once epee PCENA DE 6 Chi eee ee nrc ee eee een en eee nee ee en 7 5 1 Blank Screen No Display of Cinema Image ccceccccceeeeeeeeeeeeeees T 32 56V Moton ATUTACIS sessies Eana n R REEE 7 5 3 Image Appears Squeezed or Vertically Stretched into Center of Screen 7 5 4 No Image Just Pink SmOW ccccccccccccccccccccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees LO Non mema Display ee a a aE eee 7 6 1 The Projector is On but There s No Display ccccccccccccccceeeeeeeeeeeeees 10 2 The Display is Jittery or Unstable ereecineni n Too at Ws cog BK PAi E e E 7 6 4 The Upper Portion of the Display is Waving Tearing or Jittering 7 6 5 Portions of the Display are Cut Off or Wrap to the Opposite Edge 7 6 6 The Display Appears Compressed Vertically Stretched ee LOT Data is i 0 06 56 Om 6 2c ee ne nen en 7 6 8 Display Quality Appears to Drift from Good to Bad Bad to Good 7 6 9 The Display has Suddenly Frozen cccccccccccccccceceeeeeeeeeeeeeeeeeeeeeeeeees 7 6 10 Colors in the Display are Inaccurate ccccccccccccccceceeceeeeeeeeeeeeeeeeeeeees 7 6 11 The Display is Not Rectangular ccccccccccccccccceceeeeeeeeeeeeeeeeeeeeeeeeees PON TMS DISDlay ds INOISY aeae E 7 6 13 There are Random Streaks on the Bottom of the Image 8 Specifications dl DTS Oy E E EEE A EATA i 2 TSC E E EE EEE T E O a a N T ER oe Fd Me 161 00 T e E E E E A E AE 8 3 2
143. ected on a local network NOTE Not supported in this projector DSM Digital Source Master A title s native source files in acquisition format edited to create the distribution master and for reformatting for NTSC HDTV DVD etc and potentially archived DVI The Digital Visual Interface standard signal supplies digital RGB sync I C and clock information to the single link DVI 1 or DVI 2 ports on the projection head DETAIL The sharpness of a display from a video source DIFFUSED SCREEN A type of rear projection screen which spreads the light striking it Screen gain is typically less than 1 but audience viewing angles are increased Rarely used in cinema DIGITAL CINEMA Professional public presentation of theatrical content by electronic means particularly emphasizing projectors such as the CP2000 XB whose image source is digital data Also known as d cinema and rarely e cinema DIGITAL INTERPOLATION Also known as digital scaling The process of averaging pixel information when scaling resizing an image up or down When reducing the size of an image adjacent pixels are averaged to create fewer pixels When increasing the size of an image additional pixels are created by averaging together adjacent pixels in the original smaller image DOT CLOCK The maximum frequency of the pixel clock CP2000 XB User Manual A 5 020 100163 04 Rev 1 06 2009 Appendix A Glossary CH IS TIE l E EDID The Enhanced Extended D
144. ee the display from more acute viewing angles See Figure 2 7 Aud gain 1 ayooo Flat Screen ience Coverage Figure 2 7 Audience Coverage with a Flat Screen NOTE CP2000 XB high contrast lenses are designed primarily for use with flat screens but the projector 5 depth of field range allows the lens to be focused on mildly curved screens as well While focus remains sharp in the corners there may be significant pincushion distortion primarily at the top of the screen CP2000 XB User Manual 2 5 020 100163 04 Rev 1 06 2009 Section 2 Installation amp Setup CH IS TIE l 2 2 2 2 2 3 2 6 Rear Screen Installations There are two basic types of rear screens diffused and optical A diffused rear screen has a surface that spreads the light striking it Purely diffused screens have a gain of less than 1 The main advantage of the diffused screen is its wide viewing angle similar to that of a flat screen for front screen projection Optical rear screens take light from the projector and redirect it to increase the light intensity at the front of the screen This reduces it in other areas and creates a viewing cone similar to that of a curved front screen installation To summarize optical screens are better suited for brightly lit rooms where the audience is situated within the viewing cone Diffused screens may be better suited when a wide viewing angle is required but there is low ambient room lighting Scree
145. eeeeeeeeees B 17 B For your aO T Nol ei E E E B 18 BoT O ll ha r A EA A A E E er renee B 18 BA Te en En a aIL S EE eds ee B 18 Eximples ot ILS Command eee eee ee eee E N EE E E EE EER B 19 BAS yM Sa o e E E E E EA B 19 WA ONG AND 0 E E E E N A ouespenuateonenesuens B 22 Appendix C System Integration CSEE OPO COLO o ea E EE E E NEE C 2 C1 Standard RS 232 DEVICES acco ace cesac cies ennan AEREE C 2 a CM E E E E E E AE E T AEE E E E ET C 2 CABE PITO oe peenei iee EAE OAE ANEA NE EEEE EEA A EAA C 2 C Example GP O and D DEVi CG assina oe eE eee ee C 4 Appendix D Repacking the Projector CP2000 XB User Manual vii 020 100163 04 Rev 1 06 2009 CHRISTIE 1 Introduction This section includes information on the following 1 1 The Projector e 1 2 List of Components e 1 3 Purchase Record and Service Contacts 1 4 Who Should Use This Manual CP2000 XB User Manual 1 1 020 100163 04 Rev 1 06 2009 Section 1 Introduction CH IS TIE j 1 1 1 1 1 1 1 2 1 2 The Projector The CP2000 XB is a professional quality easy to use split body DMD projector utilizing 3 chip Digital Light Processing DLP Cinema technology from Texas Instruments Its unique separation of projection head and lamp ballast means both parts can be installed with greater ease providing the ideal solution for tight spaces and challenging rig and fly rental staging installations Whether for traditional theatre environments or other wide scr
146. een exhibitor venues the CP2000 XB provides high resolution 2D or 3D cinema images that are stunning in their size brilliance and quality This tough user friendly projector is built for frequent transport and quick setup and interfaces Projection Head in Frame with local networks typical in theatres throughout the world ore ay Expand its versatility even further by connecting non cinema DVI source material for multimedia presentations from a Figure 1 1 CP2000 XB Projector Shown variety of formats the powerful CP2000 XB is perfect for with Optional Frame any large audience venue demanding effortless installation and operation The Christie HDCP Interface Board enables CP2000 XB projectors to accept and display HDCP protected content The CP2000 XB accepts an HDCP signal from a wide variety of sources such as Blu Ray players HD receivers and HD DVD players if such sources are fed directory into the projector New Features e Motorized Lens Mount automates the process of setting the Focus Horizontal X and Vertical Y Offset and Zoom NOTE 7PC version 2 9 higher is required List of All Features DLP Cinema 3 chip electronics with 2048 x 1080 native resolution 2D or 3D Versatile electronic and optical scaling to fill wide screens CineBlack and CinePalette for deep film like blacks and superior colorimetry CineCanvas for flexible telecine grade resizing subtitling and other text and graphic overlays Tw
147. efined by the new coordinates and any display pixels outside of this area remain off black NOTE Presently only a rectangular area can be defined as shown below A trapezoidal adjustment or electronic keystone with sloped sides is not possible 1120 175 fo x Ihs y ee Custom Display Area fiz x Bs y 1120 951 Figure 3 27 Screen Presentation Coordinates CROPPING NOTES Cropping is the digital equivalent of filing aperture plates in a film If displays projector to perfect the image square ness For example 1f the aaan bottom of the image appears slightly wider than the top activate the bottom left or right cropping point in the Screen menu and change the coordinates to crop or bring in the corner s of the image slightly either enter the specific coordinates or adjust with slidebars Note that this is cropping not electronic keystone adjustment In Figure 3 28 cropping simply corrects a display that overlaps the available screen theatre screen size location In most cases cropping assumes that the entire projector display area is in use thus the coordinates initially define pixel locations on the projector s 2048 x 1080 display area Images that are significantly smaller in format may actually lie beyond the range m 3 of one or more cropping adjustments t
148. el checkbox is enabled and to all channels when the checkbox is cleared 2 Specify global parameter with G TMSA TNG LP Gm PMP 510D LP S10 005 LPM If Lamp per channel reply is channel power mode otherwise LPM 2000 returns global power mode Lamp Per Button LPB LPB O 0 Off Lamp settings will be the same for all channels LPB 1 On Lamp settings will vary according to channel LPB 1 NOTE This setting determines whether lamp mode power and intensity are the SAME for every channel i e global or DIFFERENT for each B 8 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix B ASCII Messages Function Code Examples Description and Parameters Lamp Power LPP LPP 2000 Specific power setting for the lamp in Watts LPP Value Range depends on the installed lamp LPP 2000 NOTE Specify desired channel with S If no S parameter is included the LPP setting will apply to the current channel when the Lamp Per Channel checkbox is enabled and to all channels when the checkbox is cleared E LPG PPIG 1608 LP S100 LPP If Lamp per channel reply is channel power otherwise returns LPP 2000 global intensity Lens Auxiliary LNA requires v2 7 or high LNA 1 25AN 1234567 P1 Lens type Valid lens 1 25 AN or 1 25WC P2 Lens serial number Lens Horizontal Offset LHO requires v2 9 or higher LHO 1023
149. ens menu to re center the image on the screen CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 Section 2 Installation amp Setup CH IS TIE l 6 Repeat Steps 1 5 until both sides of the image are well focused 7 Adjust the Horizontal Hold Screw to lock adjustments in place Check boresight again See Figure 2 37 2 12 3 Adjust Top Bottom Boresight When the horizontal boresight is complete focus the image at the top edge of the screen 1 Loosen the Vertical Hold Screw See Figure 2 39 2 Extend the lens focus completely 3 Adjust the Focus to retract the lens using the down arrow on the Main Lens menu Watch the image at the top edge of the screen until it comes into focus If the image appears well focused on the top edge but not on the bottom adjust the Vertical Boresight If the entire screen comes into focus skip to step 8 Vertical Boresight Bolt Vertical Hold Screw 4 Continue retracting the lens Figure 2 39 Vertical Boresight a Ifthe bottom edge of the image comes into focus before the lens is completely retracted then the image focuses in front of the screen To correct this problem adjust the Vertical Boresight bolt to direct or aim the lens mount UP towards the top of the screen to balance the top bottom edges Focus Top Center b Ifthe top edge of the image fails to come into focus then the image focuses behind the screen To correct this problem direct the lens mount DOWN
150. ent lamp size Also set the Lamp Type in the TPC Lamp menu service installer login required before turning on the projector Wor ago Figure 2 21 Move Cradle Back for 2 0 or 3 0 kW Lamps Extractor Fan and Duct For any CP2000 XB with any lamp install the Christie extractor fan and duct to pull warm exhaust air from the projector at a minimum rate of 450 CFM for 2 or 3 kW lamps or 600 CFM for 4 5 kW or higher lamps Use either the 6 in or the 6 ft long duct in one of the configurations shown in Figure 2 22 ae A WARNING A All flown components require safety cabling to supporting structure Exhaust Duct 8 t Exhaust Min 600 cfm required Figure 2 22 Extractor Fan Configurations MANDATORY SAFETY CABLING NOT SHOWN Direct the exhaust as necessary to keep ambient air temperature within operating spec refer to Section 8 Specifications If the projector is used for extended periods particularly in a confined space routing to the outside of the building may be required In all cases maintain either 450 or 600 CFM at the projector s top exit port CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 2 Installation amp Setup Table 2 3 Airflow Requirement Lamp kW Minimum Exhaust Airflow Rate 450 ft min 450 ft min 2 0 ee Co INSTALLATION Follow the installation guidelines provided below securing all components in the order that best suits you
151. enter the full resolution of the incoming source material or leave at 0 default Regardless of whether or not the original material has been squeezed for use with an auxiliary lens enter the current incoming resolution This may not necessarily match the resolution of the projector or the original filmed material depending on how the source was formatted before distribution For example an original 2048 x 1080 native source supplied pre squeezed as 1920 x 1080 requires a source file indicating this incoming 1920 x 1080 resolution To capture only a portion of an incoming image full screen like a zoom function enter the approximate horizontal width and vertical height defining the area of the image you wish to zoom in on The projector will automatically scale a center area of this size so that it fills the projector s 2048 x 1080 display and remaining data is ignored You may have to experiment with the values to accurately zoom in on a precise area and you must also define offset see below if you want to zoom in on an area other than the center CP2000 XB User Manual 3 37 020 100163 04 Rev 1 06 2009 3 38 Section 3 Operation CHA IS TIE OFFSET NOTES Offsetting an image is achieved by defining how much horizontal width and vertical height to discard Offset coordinates can be particularly useful when zooming in on a portion of the image they establish the top left corner location of the zoom area with Resolution
152. er 1476 wy lt Foot Lamberts 37 6 FL Information Indicators lt lt Pr E LiteLoc RF a zz Interlocks o coved Lamp Fan DK A Extractor Fan OK Environment Diagnostic Indicators i Lamp Door OK A Auxiliary OK hd Tamper DE System Server Diag Interrogator 15 37 36 Green All OK Yellow Environmental Diagnostics WARNING Red Environmental Diagnostics CRITICAL ERROR Main Status Custom Advanced Admin About Description alue ol Built in Self Test nH coed General Li Syster 3 coved Power up Self Test coved Security Interlock Integrity Select to expand or Peed 2C collapse menu PAF i InterFace Board a Scroll Read only i iil Diagnostics Performed If Red Failure Service neil i ORM likely required Lb FPS Load If Yellow Red stop PS FPGA Code Valid Ra operation and correct the problem System Diag Interrogator a 15 38 23 NOTE Requires service installer login Figure 3 5 Status System Menu NOTE The Status System menu shown here is available to all users For information about the password protected Status Server Status Diag and Status Interrogator menus refer to Section 3 11 Working with Servers and Diagnostics Table 3 1 Summary of Status System Menu STATUS SYSTEM MENU ENTRIES SOURCE Projector Input Source connection location of current signal CINE IPM NOT APPLICABLE FOR CP2000 PROJECTORS CP2
153. erter lens into place in front of the primary zoom lens of the projector This lens increases magnification across the width only regaining the original proportions in the image and is often used in theatres where side masking can be moved aside 3 10 Working with 3D NOTE For a description of each 3D control refer to Section 3 5 Using the Touch Panel Controller A single projector can display 3D images as described below Such images require a 3D capable source as well as additional hardware and cabling in order to be displayed and interpreted correctly in a typical stereo 3D viewing environment 3 10 1 3D Description 3 64 In simple terms images generated from a 3D cinema source consist of a series of images frames or fields that alternate quickly between two slightly different viewpoints corresponding to the physical separation of our left and right eyes called parallax When these frames are displayed with enough speed and viewed with special glasses synchronized with the left right frame sequencing the resulting single perceived image appears with much the same depth and perspective we sense in the real world The new full resolution triple flash hardware Brilliant3D includes an FPGA Formatter Interface Board FFIB which allows for full 2K resolution using a 6 2 frame rate multiplication Triple Flash Triple Flash 3D is reference to a frame rate that is of a high enough frequency to eliminate flicker as noticeable by the eye Th
154. ervoir to critical electronic components located near the front of the projection head The coolant should fill slightly more than half of the reservoir to ensure adequate circulation Use only the Christie approved coolant Jeffcool E105 provided in the liquid coolant fill service kit P N 003 001837 02 Danger HAZARDOUS SUBSTANCE The coolant used in this product contains ethylene glycol Use caution when handling Do not ingest The reservoir which is located in the igniter compartment is factory filled and does not require draining before projector transit Top up as necessary Warning Check regularly for leaks and proper liquid level CP2000 XB User Manual 2 19 020 100163 04 Rev 1 06 2009 Section 2 Installation amp Setup CH IS TIE 2 5 Installing and Connecting Sources NOTE 7o maintain radiated emissions compliance do not connect I 0 cables to the projector without connecting the source or receiver at the other end 2 5 1 Cinema Connect your server source to either the HD SDI A or HD SDI B connector on the Communications and Source Connection Panel at the rear of the projector Connect two independent sources or connect a single source to both ports to create a dual link cinema input D E HD SDI A DVI 2 DVI 1 Figure 2 27 Connecting Cinema and Non Cinema Sources 2 5 2 Non Cinema To display alternative content from a DVI source or from Christie s Cine IPM 2K remove the acc
155. es 1 what portion of the projector s display panel you wish to use and 2 what cropping is needed to disguise possible keystoning or other geometric aberrations Once saved a screen file can be used with any incoming source as desired screen data is not included in a PCF and is independent of Source settings Consider screen files as convenient compensations for physical limitations in the environment You will typically need one or two screen files per site Custom Admin About Main Status Letter Box Enter a check z mark to see ALL O f 47 ya Lens data Factor C C C jio79 y 1 a Anamorph x Define display area needed Adjust to define new display area and or cropping a screen file for gt Create Screen Restore Defaults lt P E a access in el EEE eee efault settings Custom menu E z T Source Screen Samut IP Contig General Lamp Save settings in Cancel new unsaved settings Figure 3 26 Admin Screen Menu Options Table 3 16 Admin Screen Menu Options ADMIN SCREEN MENU OPTIONS Presentation Presentation points define the display size and location default full 2048 x 1080 panel See Presen tation Notes below Cropping Cropping hides unwanted data useful if the image appears keystoned etc See Cropping Notes below Letterbox Letterboxing ensures that all image data is displayed and its aspect ratio is maintained Se
156. ess panel located on the underside of the projector near the air filter Connect two independent sources or connect the Cine IPM 2K to both ports for 10 bit processing Add an exit hole to the panel or leave the panel off 2 20 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 2 Installation amp Setup 2 6 Connecting for Communications Many communications with the projector are initiated on the TPC mounted at the rear of the projector Depending on the installation you may also need certain other serial and or Ethernet links to the projector such as from a server or PC functioning as a controller or from an existing on site network including other related equipment These system connections are typically done at time of installation but are fully accessible and can be changed at any time In rare cases serial and or Ethernet links are needed only during installation and are disconnected afterwards Connect your devices to the Communications and Source Connection Panel at the rear of the projection head S Nf Identical Ethernet ports O S r Cinema Server Figure 2 28 Communication Links with Projector TPC Connect the TPC cable to the 6 pin XLR connector This connector then routes to an internal 5 port Ethernet hub connected to the projector s main processing electronics PC Laptop Server or Network To communicate with the CP2000 XB from a compute
157. est pattern filename to display pattern 6699 Enter to turn off the test pattern CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix B ASCII Messages Function Code Examples Description and Parameters Lamp Changed LPC LPC 60123456 100 CDXL 20 Records the serial number hours logged on lamp lamp type and Ignition Difficulty or LPC reason for change of the newly installed lamp thus resetting the 60123456 100 CDXL 20 3 lamp time to 0 for logging time Serial number 32 characters max Valid Lamp Types CDXL 20 CDXL 30 CDXL 45 CDXL 60 CXL 20 CXL 30 CXL 45 CXL 60 Other 16 Etc Valid Change Reason can be sent as number or text Q 1 Usage Hours Exceeded 2 Light Level too Low 3 Ignition Difficulty 4 Light Unstable flicker 5 Was Temporary Lamp 6 Lamp Type Change 7 Other Lamp History HIS HIS 021 00001 1234567 00007 2007 Lamp history describes lamps used in the projector See Messages 08 01 15 58 Other 20 00000 00000 With Multiple Parameters in this Appendix 00000 000 Usage Hours Exceeded Lamp Hours of Use LPH LPH 0528 The hours logged on the current lamp 0 9999 Lamp Hours Limit LPL LPL 750 The hours that a lamp can be used before a warning message appears Range 0 20000 hours Lamp Intensity LPI LPI 12345 The light
158. fies which projector the TPC is currently set to control HOW TO CHANGE YOUR PROJECTOR S IP NETWORK ADDRESS For a stand alone projector its default Ethernet network settings are fine and should not be changed In a projector that is connected to the network however this default address will likely be invalid for the network at a given site Consult the site s network administrator to determine the necessary settings for compatibility with the local network then use the TPC to define these new settings in the projection head NOTES 1 password protected requires a Christie installer login 2 projector can be on the network during these changes if desired l Select the Projector button and enter a checkmark in the Change Config checkbox This will enable editing of the Projector Ethernet Configuration text boxes 2 Enter the projector s new valid and unique IP Address desired The last octet can be any value from 10 99 Enter the projector s new Subnet Mask address settings required Define Network Must match TPC settings IP Address ise fies 206 m t Defines projector Subnet Mask ess fess a0 fo Figure 3 34 Change Projector s IP Address Select the Apply button to implement the new address settings in the projector A caution will remind you that the address must be unique and valid for the site if you are unsure cancel and consult again with the network administrator Otherwise click OK to fini
159. for use 2 Buttons may have any icon and or text ey A 1998x1080 A 2048x558 Flat srz Scope we A 1998x1080 A SOdexe58 Flat PS Scope F3 1 Select pre defined source sii large button BA Reserved E Reserved ow 2 Image will change FCF Flat PCF Scope BA 1920x1038 a 1920x804 iF Flat P3 Scope PS cH 1 8 CH9 16 To additional sources 15 17 ele ri Figure 3 38 Source Selection on Main Menu sample WHAT HAPPENS WHEN A BUTTON IS SELECTED For any channel button on the Main menu the projector interprets incoming signal data according to one of eight user selectable display setups defined at the time of CP2000 XB installation and or with each subsequent release of a new digital cinema feature and stored in projector memory Each display setup consists of Projector Configuration File PCF information as well as additional processing display parameters and screen settings optimized for a particular cinema feature or alternative content source For proper processing and display of a source select pre assigned channel button corresponding to the setup you wish to use the button will then appear recessed and the projected image will update according to the display setup assigned to this button No further adjustment of the image should be necessary To change to a different presentation select a different channel button 3 50 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section
160. front of prime lens to back of wide converter lens barrel Zoom Lens Clearance 1 45 1 8 1 8 6 mm 2 1 8 2 4 1 13 6mm 2 2 2 3 0 1 6mm 2 3 VERTICAL LENS POSITION Adjust the converter lens vertically so that it is exactly on the center line with the pre adjusted prime lens 4 HORIZONTAL LENS POSITION Adjust the converter lens horizontally so that it is exactly on the center line with the pre adjusted prime lens 5 PITCH ADJUSTMENT Adjust the top and bottom clearance between the wide converter and prime lenses until they are equal using a wedge gauge or small calipers 6 YAW ADJUSTMENT Adjust the two side clearances between the wide converter and prime lenses until they are equal using a wedge gauge or small calipers 7 RECORD SERIAL NUMBER Enter the serial number of your converter lens in Advanced Lens menu CP2000 XB User Manual 2 29 020 100163 04 Rev 1 06 2009 Section 2 Installation amp Setup CH IS TIE l 2 13 Fold Mirror and Convergence Adjustment In rare instances shipping and handling may affect the precise factory alignments of one or more optical components as a final step of installation the installer may have to adjust the fold mirror and or convergence of the DMDs as described here DMD CONVERGENCE A convergence problem is evident when one or more projected colors red green blue appears misaligned when examined with a proper convergence test pattern where normally the 3 colors should
161. g Proper Cooling LAMINAR AIRFLOW DEVICE LAD Whenever checking replacing the air filter on the side of the projector also visually check the small square laminar airflow device LAD just beyond the filter opening The LAD should be nearly white in color if very dark rare it may have to be replaced by a qualified service technician Contact Christie or your dealer 6 4 Replacing the Lamp and Filter The high brightness of your projector is provided by a Xenon lamp mounted at the ends within a reflector housed in the locked lamp compartment of the projection head When the lamp approaches the end of its life it must be replaced do not exceed warranted lamp life by more than 20 as an old lamp becomes increasingly and dangerously fragile resulting in possible explosion To determine the age of your current lamp consult the Status menu in the Touch Panel Controller Lamp hours appear under Environment Lamp Lamp hours are also displayed in the password protected Advanced Lamp menu and the Advanced Lamp History menu It is recommended that you replace the air filter with every lamp replacement or sooner in dusty or dirty environments Check its condition monthly in all projectors 6 4 1 Lamp Replacement Procedure NOTE For this procedure you will need a compatible Christie Xenon CDXL or CXL lamp as shown in Section 8 Specifications never install a lamp intended for a different model or projector Warning 1 Make sure to use the correct
162. gator 15 18 20 amp maan 3 59 Status Server Menu Options 3 70 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation Status Diag Menu The Status Diag menu provides status information about projector components and the current cinema source and enables log files for each device to be saved to the TPC s storage card for diagnostics Info about projector Write SMPTE log components to TPC s storage card directory Write projector log or self test log to TPC s storage card directory Clear SMPTE errors Useful for testing if they recur Test every projector component NOTE Do not use during a show SMPTE log of source server errors Re boot and doa Self Test Figure 3 60 Status Diag Menu Options Status Interrogator Menu The password protected Status Interrogator menu l Ad d Ad About enables the collection of advanced level status ee information that can assist in the diagnostics of projector components Interrogator can be run in two modes and enables the collection of log files only Basic Mode or log files plus registered batch files Enhanced Mode These files are then stored on the TPC s storage card For Interrogator to successfully retrieve these diagnostic files the projector must remain in its failed state with incorrectly displayed image on screen NOTES 1 Always run Interrogator first before power Diag Interrogator fo
163. gh intensity light source or flashlight Clean them only when dust dirt oil or other marks are obvious Never touch an optical surface with your bare hand always wear latex lab gloves When to Check LENS A small amount of dust or dirt on the lens has minimal effect on image quality to avoid the risk of scratching the lens clean the lens only if absolutely required See Section Cleaning the Lens below LAMP REFLECTOR Inspect the mirror surface reflector for cleanliness only during a lamp replacement when the lamp is out If necessary clean as described below make sure to wear protective clothing while inspecting or cleaning Note that color variation on the reflector surface is normal Supplies For cleaning off dust and or grease you will need Soft camel hair brush Dust free blower filtered dry nitrogen blown through an anti static nozzle Dust free lens tissue such as Melles Griot Kodak tissues 18LAB020 Optowipes 18LAB022 or Kim Wipes or equivalent Lens cleaning solution such as Melles Griot Optics Cleaning Fluid 18LAB011 or equivalent For lens only Methanol For reflector only Cotton swabs with wooden stems only Lens cleaning cloth microfibre such as Melles Griot 18LAB024 or equivalent CP2000 XB User Manual 6 5 020 100163 04 Rev 1 06 2009 Section 6 Maintenance CH IS TIE l 6 3 3 6 6 Cleaning the Lens IF DUSTY Brush most of the dust off with a camel hair brush and or blow dust away with co
164. great pressure when hot and may explode causing personal injury and or property damage Allow to cool completely STEP 2 Turn OFF Remaining Circuit Breakers After allowing the fans to run for at least 10 minutes turn OFF the remaining INTERNAL and PROJEC TOR circuit breakers located on the breaker panel of the projector STEP 3 Disconnect Projector From AC Supply Warning SHOCK HAZARD Disconnect from all AC at ALL wall breakers STEP 4 Open Remove Filter Door Open filter door by loosening 2 corner screws flat screwdriver and lift off door 1 and 2 in Figure 6 4 STEP 5 Replace Air Filter Slide the filter up and discard Insert the new air filter following the labeling for proper inside outside ori entation Slide all the way down into its slot 3 and 4 in Figure 6 4 Warning Use only Christie filters Never operate the projector without the filter installed CP2000 XB User Manual 6 11 020 100163 04 Rev 1 06 2009 CHRISTIE Section 6 Maintenance STEP 6 Close Replace Filter Door With the filter in place insert the bottom tabs of the filter door into the corresponding slots close the filter door and secure with 2 screws 5 and 6 in Figure 6 4 8 Open or remove door 2 screws 1 Open filter door 3 Remove old filter 6 Secure filter door 2 screws Figure 6 4 Repla
165. h the line voltage available at the site Remove the lamp ballast cover to access the switch and determine its setting togele left for 200 VAC supplies toggle right for 400 VAC supplies factory default 200 VAC Modify the plug type as necessary as a delta load with safety ground it has no neutral Confirm that the ballast s 3 phase status lights are on and that the adjacent voltmeter displays an acceptable AC level for your ballast and region Refer to Section 8 Specifications for details Then set the ballast AC ON OFF switch to ON and listen for the internal cooling fan start up NOTE There is no other indication of ballast ON status Interlocks Control A NOTE A Cable length defined in software Figure 2 3 Connect Head to Ballast A NOTE 7 kW Internal Incoming Line Voltage switch setting must match AC available at the site 3 kW may not be exactly as shown pen i ia interlocks il Control Oe ooo DC 0 a ND A Ni Breaker ON Y J 0 6 line cord Y DN A Connect to projector Connect to AC supply Single phase Voltmeter 400V ie ow ballast e 200 VAC in N America e 208 VAC in Japan e 380 400 415 VAC in Europe Modify plug as necessary Figure 2 4
166. han 10 brighter or dimmer than the LiteLOC setting the recovery will be immediate When re enabling LiteLOC from a brightness setting that differs by only 10 or less the recovery will be gradual ie Adjust Mel fen 51 5 aar ar LiteLOC no longer in effect H Ad at ee ai PERPA 20 44 E Meter tracks Figure 3 47 Using a Specific Power Level CP2000 XB User Manual 3 59 020 100163 04 Rev 1 06 2009 Section 3 Operation CHix IS TIE l 3 8 4 3 60 UNDERSTANDING LAMP POWER VALUES The Lamp Power range of 75 110 represents 75 110 of the power F REP appropriate for the installed lamp In other words you can apply anywhere from 75 of the maximum power intended for the installed Lamp Power Hen hh lamp up to an over drive that exceeds the maximum rating by i approximately 10 Both current amps and power watts thresholds Applies 75 110 of the lamp power rating are read for the installed lamp EXAMPLE If a 4 5kW lamp is installed Lamp Power ry 110 0 T3 Keep in mind that higher lamp power settings do shorten lamp life for Biia ehageel pate best results avoid over driving a lamp for extended periods When using watts LiteLOC which automatically increases lamp power over time check Figure 3 48 Lamp Power Values the Status menu lamp power readings periodically as the lamp ages to prevent prolonged over driving Table 3 23 Lamp Current Ranges AN LAMP CURRENT
167. hanges to affect to Channel the selected channel Repeat for every channel that requires the same ILS values CP2000 XB User Manual 3 27 020 100163 04 Rev 1 06 2009 Section 3 Operation CH IS TIE l Channel Lens Menu Disabled The Channel Lens menu is grayed out when the Auto ILS feature of the Main Lens menu is not selected See Figure 3 15 In the instance that an ILS is not installed on the projector or if the Installed option in the Intelligent Lens System region on the Advanced Lens menu is not selected the Custom Lens menu will not display ain Status Custom advanced Admin about Dag m EE eel Page i Page2 s0 contol Lame ters Figure 3 15 Custom Lens Menu Disabled 3 5 6 TPC Advanced Menu All password protected requires Installer Admin or Advanced User rights except for the New Lamp button accessible by Operator login The TPC Advanced menu consists of six different submenus Preferences Lamp Lamp History Lens Test Patterns and User that enable installers administrators and advanced users to define numerous system operating parameters load and or display test patterns work with lamp settings and set up users and their TPC access rights 3 28 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation Advanced Preference Menu The Preference menu provides access to all test patterns as well as certain system parameters Main Status Cu
168. he bandwidth or frame rate of the system thus formats beyond those shown in Table 5 1 may also be compatible CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 5 Non Cinema Operation 5 1 1 Dual and Twin Link DVI 5 2 Although dual link and twin link input options appear in the TPC Custom menu using the pair of DVI ports for a dual link signal that is two data streams and one clock via one dual link cable requires an adapter that accepts the dual link DVI connector Using the ports for a twin link signal two data streams with their own clocks each on their own single link cable requires a source that can provide this unique type of DVI output Either of the proposed configurations would increase DVI bandwidth DUAL LINK DVI TWIN LINK DVI NOTE One shared clock 165 MHz max NOTE 2 separate clocks 165 MHz max O O DVI 2 DVI 1 ae dual link cable amp connector f H single link connector connector Ba Adapter E DVI Source P Twin link E DVI Source Dual link Figure 5 2 Proposed Dual link and Twin link DVI Configurations NOTES 1 Neither the Christie dual link adapter nor the proposed 3rd party twin link source and cables shown here are currently available 2 Using both DVI ports with the Christie Cine IPM 2K enables 10 bit output and displays Co
169. he ballast breaker switch to ON The internal ballast fan should start up NOTE There is no other indication of whether the ballast is on or not 6 Atthe TPC go to the Admin Lamp menu password required Enter the size of the lamp currently installed in the projector factory default 2 0 kW 7 Still in the Admin Lamp menu set Cable Length m to match the length of DC cables currently connected between your lamp ballast and projection head range is 2 30m or 62 100 ft 8 On the Main menu press the lamp button and hold for 2 seconds The lamp should ignite and full power is maintained for 15 seconds Press the desired channel button on the Main menu The source will be displayed according to pre defined factory defaults for this channel Adjust or apply new settings as described in Section 3 5 Using the Touch Panel Controller IF THE LAMP DOES NOT IGNITE e If a safety interlock switch is open such as when the lamp door is ajar the lamp cannot be struck The PROJ STATUS light on the rear of the projector will be red and the error will be indicated on the status display and LCD window e If the lamp fails to ignite even though the interlock system is OK the projector will automatically re try ignition using 100 of the maximum power acceptable for the installed lamp If this re try also fails a new lamp is likely needed NOTE For complete power up troubleshooting refer to Section 7 Troubleshooting Power Down Procedure
170. he projected display image CP2000 XB User Manual 3 9 020 100163 04 Rev 1 06 2009 3 10 Section 3 Operation CHA IS TIE l TURN THE LAMP ON or OFF To toggle the lamp ON OFF press and hold the lamp button LOG ON By default with no login the TPC will offer only the three general user menus intended for daily operation refer to Figure 3 2 To access other menus you must log on as a specific user with more rights Press the user level icon in the bottom right corner of any screen then enter the desired user name and password in the text boxes provided OPEN OR CLOSE THE DOUSER SHUTTER To blank the display for instant picture muting and cooler stand by mode press the raised douser shutter key showing a lens that is currently projecting light Closing the douser slides a shutter blade in front of the lens and reduces lamp power to 50 of its maximum rating or 75 if using a 2 kW or 3 kW lamp To open the douser and restore previous lamp power press the depressed douser key currently showing a darkened lens with red warning circle MOVE THE AUXILIARY LENS Toggle the current location of the optional auxiliary lens position it either in front of the primary lens to stretch the display horizontally or move it aside NOTE For complete operating instructions refer to the information supplied with the Motorized Auxiliary Lens Mount SEE TEST PATTERNS To display a test pattern press the Test Pattern button repeat to cyc
171. he serial number of a newly installed lamp This button is also available with an Operator login with the rest of the Lamp menu disabled trefer back to Figure 3 2 Read only lamp info s Custom Advanced Admin Abqut Lam Set maintain consis ia 147 Current light sensor tent light output P reading Volks 29 6 Adjustable from 75 110 if LiteLOC is wakts 4351 LiteLOC setting not in use or as Lamp Fower esi 750 v j desired brightness temporary override Approximate LampLo Position lamp for best Foot Lamberts Light Output sensor light output t x 70 0 0 FL reading x axis horizontal ol iS aoe y axis vertical ry j a Hours 153 z axis fore aft We ee z b i Do Auta New Lamp Preference Lamp Lame History Click to record new lamp serial and reset lamp timer 11 10 37 Figure 3 17 Advanced Lamp Menu Options Table 3 10 Summary of Advanced Lamp Menu Options ADVANCED LAMP MENU OPTIONS Set Brightness Maintains a chosen light level at the screen over time the lamp ballast will gradually increase power to LiteLOC the lamp as necessary until it reaches the maximum level possible for the installed lamp To disable LiteLOC temporarily or permanently clear the LiteLOC Enable checkbox or adjust Lamp Power directly With the desired light output measured at the screen typically 14 fL press the Set Br
172. heatres or large rental staging venues Such users may also be trained to replace the lamp and air filter but cannot install the projector or perform any other functions inside the product enclosures SERVICE Only trained and qualified Christie service technicians knowledgeable about all potential hazards associated with high voltage ultraviolet exposure explosion hazards of high pressure arc lamps and high temperatures generated by the lamp and associated circuits are authorized to 1 assemble install the projector and 2 perform service functions inside product enclosures CP2000 XB User Manual 1 5 020 100163 04 Rev 1 06 2009 Section 1 Introduction CH IS TIE l 1 4 1 Labels and Marking Observe and follow any warnings and instructions marked on the projector 7 7 NA cd Danger symbols indicate a hazardous situation which if not avoided will result in death or serious injury This signal word is to be limited to the most extreme situations MAAA e Warning symbols indicate a hazardous situation which if not avoided could result in death or serious injury Tel Caution symbols indicate a hazardous situation which if not avoided could result in minor or moderate injury NOTICE Addresses practices not related to personal injury 1 4 2 Typographical Notations 1 6 The following notations are used throughout this manual Keypad commands and PC keystrokes appear in bold small caps such as POWER INPUT ENTER etc
173. hus you will not see evidence of cropping on the edges adjust Cropping until no data appears outside T theatre screen l To correct a bowed edge so that it appears straight in the display activate one of the cropping bow points between two corner points and adjust the slider or enter the specific x or y value desired Figure 3 28 Simple Cropping Example CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation LETTER BOX NOTES Use letter box for virtually all normal operation It ensures that all incoming data will be displayed within your defined presentation area and nothing will be discarded If desired any black bars unused pixels could then be cropped off using the cropping control Although disabling the letter box control also fills the defined presentation area any extra data beyond this area whether top and bottom or left and right will be discarded Unused pixels J Complete image Incomplete image Figure 3 29 Letter Box vs Non Letter Box Admin Gamut Menu The primary function of the color Gamut menu is to ensure that the projector can achieve any specific known and pre defined industry color performance standard called a target color within its current environment and within a desired tolerance In this menu you can record measurements for currently projected uncorrected colors modify or create custom Target Color
174. ically re try ignition using 100 of the maximum power acceptable for the lamp If this re try also fails and there is no interlock problem such as an open lamp door a new lamp is likely needed CP2000 XB User Manual 3 57 020 100163 04 Rev 1 06 2009 Section 3 Operation CHA IS TIE l 3 8 3 Adjusting Lamp Power LiteLOC or Manually NOTES 1 Requires Advanced Admin TPC rights 2 Keep in mind the formula Current Amperes x Voltage Volts Lamp Power Watts 3 Adjust LiteLOC before or after adjustment of lamp position There are two different lamp modes for general operation you can maintain either a specific brightness level LiteLOC or a specific lamp power level Using LiteLOC Maintain a specific brightness level from your lamp over time as follows Figure 3 45 1 Inthe TPC s Advanced Lamp menu adjust Lamp Power until the desired light output is reached at the screen typically 14 fL Any LiteLOC will automatically be disabled Step 2 Main Status Custonp Advanced Admin About LiteLO Lamp Light Amps 159 Step 3 Enable ime Volts 30 0 watts 4770 Step 1 Lamp Power fee 75 0 ja w Approximate Fook Lamberts 0 0 FL oe F T Fou ae 153 Preference Lamp Lamp History Lens Test Pattern User 3 11 09 11 Figure 3 45 Setting LiteLOC 2 Select Set to record the current brightness reading in memory NOTE Arbitrary units
175. icensed software intended for Christie installers only Many of its functions are now available at the TPC DCP Librarian is a comprehensive Windows based software application used for calibrating image color performance and defining electronic screen masking required in your particular installation and for creating individual Projector Configuration Files PCFs and specific source files necessary for proper display of incoming material DCP Librarian also defines the system network configuration for communication links to the projector transmitting information to and from the CP2000 XB via an Ethernet or RS 232 connection Chief functions many of which can be done at the TPC are introduced below Color Calibration After the CP2000 XB is installed and all components are mechanically aligned for optimized light output and geometry at the screen its electronic system processing must be calibrated to ensure accurate color display in the new environment In this one time global calibration the installer measures initial colors at the screen and enters this data called Measured Color Gamut Data into Windows based DCP Librarian software installed on a laptop The software then calculates precise corrections needed for regaining the desired color performance called Target Color Gamut Data and essentially compensates for the type of port window if present screen lens light output ambient light and other current environmental factors tha
176. ightness button to automatically enable LiteLOC The current brightness level will be maintained as long as possible NOTE Arbitrary units of measure appear here not footlamberts or lumens Indicates what percentage of power appropriate for the installed lamp to supply to the lamp automatically overriding any LiteLOC setting that may be in effect This causes the bar graph to rise or fall but the LiteLOC line and Set values will not change unless Set is pressed defining a new LiteLOC setting Refer to Table 3 10 for lamp power ranges LampLOC LampLOC buttons activate motors that reposition the bulb in the projector for optimized light output Use the Do Auto button recommended or the individual buttons NOTES 1 Lamp must be ON to begin If it is turned off during a re positioning the bulb will return to its former position 2 Douser opens and remains non functional during a LampLOC adjustment Lamp Read only Indicates the current lamp age amps current volts voltage and watts lamp power Light Level Activates the lamp history window and text editing box for recording a new lamp s serial number which resets the lamp timer This button can also be accessed with an Operator login at the TPC Indicates current light output shown as solid vertical bar and LiteLOC level set single horizontal line Consider the value at the top of the meter as arbitrary i e not representing actual lumens or fL
177. in addition to interlocks and problems with the SSM I2C or lamp which are all permanent triggers It is recommended that all triggers remain enabled during normal operation Disable only in an rare emergencies when the alarm appears to be mal functioning without real errors Enter the hours 0 5000 that are expected for this lamp typically no more than the number covered under warranty Expiry Message Select to display the Lamp Expiry Message on the TPC when the lamp reaches its defined lamp limit Choose English or Chinese TPC menu text for next re boot System Calendar Reset the system date time Adjust the desired component date hour minute second and save with the Set amp Clock button Screen Saver Enable disable a TPC screen saver and set its start up delay NOTE To use a unique screen saver a user defined bmp must be downloaded to the TPC replacing the default CP2000 XB User Manual 3 29 020 100163 04 Rev 1 06 2009 Section 3 Operation Advanced Lamp Menu CHRISTIE The Lamp menu provides controls for optimizing lamp alignment LampLOC maintaining a specific light output over time LiteLOC or setting a precise power level for the lamp Two read only areas display related lamp performance details the side bar graph represents the current light output and if LiteLOC is enabled a heavy line shows the chosen LiteLOC setting In addition the New Lamp button activates a window for entering t
178. in their width to height aspect ratio as shown below Flat Image Scope Image Aspect ratio 1 85 Aspect ratio 2 39 Figure 2 9 Typical Wide Formats Achieving either of these displays from a variety of incoming source material that may or may not be ina format matching that of the screen depends on lenses proper settings in the projector and certain room conditions Refer to Section 4 2 Image Formats CP2000 XB User Manual 2 7 020 100163 04 Rev 1 06 2009 Section 2 Installation amp Setup CH IS TIE l 2 2 4 Ambient Lighting 2 2 5 2 3 2 3 1 2 8 The extraordinary brilliance of this projector is certainly well suited for locations where ambient lighting might be considered less than ideal for projection Even a typical room or large auditorium fully lit with ceiling lights and windows rarely requires special attention Contrast ratio in your images will be noticeably reduced only if stray light directly strikes the screen such as when a shaft of light from a window or floodlight falls on the image Images may then appear washed out and less vibrant In general avoid or eliminate light sources directed at the screen Other Considerations Other considerations and tips that can help improve your installation e Keep the ambient temperature constant and below 35 C 95 F Keep the projector away from heating and or air conditioning vents Changes in temperature may cause drifts in the projector circuitry
179. ined by installer or administra tor Measured Color Pull Down OFFset Native color reference Choices Onsite Field i Define frame offset defined by installer Z Default OnSite LUT CLUT SMPTE Field Bit Complex Look up Table Type Linear _9x9x9 Normal Select field offset polarity be Applies a 3 dimensional color cu for increased color accuracy Page 1 page 2 3D Control Lamp Lens GD 15 19 53 Figure 3 10 Custom Page 2 Menu Options Table 3 5 Summary of Custom Page 2 Menu Options CUSTOM PAGE 2 MENU OPTIONS Auxiliary Lens In Sets whether or not the optional auxiliary lens is used with this channel Pull Down Re Sync This command is used to enable or disable the re synchronization function associated with the Pull Down Sequence It is sometimes useful to disable the re synchronization function when the time code is not running at the proper rate such as when a jog control is being used with a tape machine Screen Identifies sets display area masking cropping and expected lens for the current source Choices are pre defined using DCP Librarian or the TPC Admin menus Screen settings are not included in a PCF Measured Color For a given channel source select the desired MCGD file representing native uncorrected colors to use as a reference for calculating target color processing Default OnSite See also Admin Gamut menu LUT CLUT A C
180. ing a Lens Lamp and Cooling 2 4 1 Install Lens es Primary Lens Auxiliary Lens Installation Optional 2 4 2 Install First Lamp 2 4 3 Cooling Extractor Fan and Duct Side Venting Duct Adapter Liquid Cooling 2 5 Installing and Connecting Sources 2 5 1 Cinema 2 5 2 Non Cinema 2 6 Connecting for Communications TPC acer es E E docneeedaeepaes PC Laptop Server or Network 2 7 Connecting the Ballast 2 7 1 Configuring the Ballast for Incoming AC 2 7 2 Connect to Projector 2 8 Initial Power Up Set Lamp Type Set Cable Length Power up 2 9 Maximizing Light Output 2 9 1 Determining Screen Brightness fL 2 10 Basic Image Alignment 2 11 Basic Optical Alignment Procedure 2 12 Offset and Boresight Alignment 2 12 1 Adjust Offset 2 12 2 Adjust Left Right Boresight 2 12 3 Adjust Top Bottom Boresight 2 12 4 Copy the Channel Settings To Another Channel 2 12 5 Add Auxiliary Lens Wide Converter Lens 1 26x 2 13 Fold Mirror and Convergence Adjustment 2 14 Calibrating the CP2000 XB System Color Calibration Electronic Screen Masking PCFs Rare 3 Operation 3 1 Projector Basics 3 1 1 Components Features Air Filter Ballast Breaker ON OFF U Channels for FredFrame Communications and Source Connection Panel CHRISTIE CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE i Table of Contents ESA all B10 6 PEE ne een EAE AE E A EE 3 4 ae Pita COA CHONG E A E E AE E EAEE A EE 3 4 D A E A E A E E A 3 4 Lens
181. ing research specifications are subject to change without notice NOTE The illustrations provided are to enhance the understanding of the written material They are graphical representations only and may not represent your exact projector model e 1 Display e 8 2 Lenses e 8 3 Inputs e 8 4 Touch Panel Controller e 8 5 Power Specifications e 8 6 Lamps e 7 Regulatory e 8 8 Environment e 8 9 Weight and Size 10 Standard Components CP2000 XB User Manual 8 1 020 100163 04 Rev 1 06 2009 Section 8 Specifications CHA IS TIE 8 1 Display Panel Resolution Pixel format H x V on 3 DMDs 2048 x 1080 and Refresh Rate 2D Refresh rate DLP Cinema processing 23 97 48 Hz SMPTE 292M 2D Refresh rate Non cinema processing 23 97 85 Hz VESA DVD 3D Refresh rate 24 Hz per eye 144 Hz max Pixel Clock rate 150 MHz max Achievable Requires maximum output conditions 14 fL on 25m 75 ft screen or 17m screen Brightness 2 kW or 3 kW Achievable 2000 1 full on off Contrast Ratio Colors and Gray Displayable colors 35 2 trillion Scale Gray scale resolution a each per RGB component 45 total inear White Point Nominal white x 0 314 0 002 full white after calibration in telecine mode y 0 351 0 002 8 2 Lenses Primary Zoom Lenses Part Max of Image Below or Above High Contrast Lens Center 100 vertical 70 horizontal 100 vertical 70 horizontal 100 vertical 70 horizont
182. isplay Identification Data standard established by VESA enables properties such as resolution of a display device to be detected by the display card in a controlling device such as a PC The PC in turn can then output in a matching format to fill the display Some sources used with the projector are VESA E EDID reported E STOP Emergency stop of the presentation due to equipment failure a commotion in the audience or any trigger from the theatre s life safety system that could require stopping the show raising the house lights and enabling a PA announcement FOOT CANDLE The intensity of visible light per square foot FOOTLAMBERTS The luminance brightness which results from one foot candle of illumination falling on a perfectly diffuse surface 1 fL 3 423 candela per square meter cd m Note that SMPTE RP 98 calls for theatre screen luminance of 12 to 22 fL 16 2 fL 55 7 cd m is the open gate target according to SMPTE 196M For cinema applications xenon lamp wattage is approximated to achieve this level using 12 W ft x screen height squared or 5 W ft of total scope image area for matte screens and typical lenses FRAME RATE The frequency at which complete images are generated For non interlaced signals the frame rate 1s identical to the vertical frequency For interlaced signals the frame rate also known as field rate is one half of vertical frequency GAIN OR SCREEN GAIN The ability of a screen
183. ivity Program your controller to send a PNG message every 5 10 minutes to maintain communication and keep the socket functioning Important 7o prevent shutdown of the socket program the controller to send a PNG every 5 10 minutes SHUTDOWN Warning You must close the application and shut down the socket properly before shutting down the control ler CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation 3 7 3 7 1 3 7 2 Upgrading SSM Firmware These instructions explain how to upgrade SSM firmware without upgrading the rest of the software The correct SSM firmware must be downloaded to the SSM in order for the DMD temperature warning and shutdown limits to be properly set You will use an FTP program to transfer the new version file from your PC to the TPC currently connected to your CP2000 XB projector Requirements e TPC 642 or TPC 60 or TPC 66 used with any CP2000 XB projector e Windows 2000 or XP running on a laptop or PC e Correct SSM Firmware version e Version 2 1 for CP2000 XB e FTP application such as FFFTP or WS_FTP or as provided in Windows XP or Internet Explorer Update Procedure NOTE Screenshots throughout this section are for representation purposes only and may differ slightly from those on your screen FFFTP is a freeware FTP client application recommended for communicating with the TPC via file transfer protocol NOTE FF FTP is the only supported FTP software
184. l fails replace the lamp OTHER SSM Communication Error Check cabling Cycle projector power for a normal start up Check LEDs on card cage boards which can indicate a light engine problem instead Check LVPS Processor voltages Also if shutter or lamp are functioning normally SSM likely OK C Communication Error There may be a power problem with the main electronics PC Check LVPS Proc voltage adjustments LENS MOUNT A communications error with the ILS motor con Check cabling Cycle projector power for a normal start up trol board has occurred Please ensure that all cabling is correctly connected ILS Motor Control Board Sensor Failure This error will only be detected on a lens reset or lens calibrate Check the sensors It is cleared by cycling the projector power or performing a lens reset ILS Motor Control Board In Boot Program Mode If this message remains for longer than 4 seconds try re powering the TPC or upgrading the MCB software ILS Motor Control Board Main Code CRC Upgrade MCB software 1 A failed interlock automatically prevents power from going to the lamp and disables the lamp button on the TPC Main menu Since most interlock alarm conditions are triggered by switches check the operation of these switch levers 2 When you have restored interlock integrity the lamp button on the TPC Main menu is automatically re enabled CP2000 XB User Manual 3 17 020 100163 04 Rev 1 06 2009
185. l ri l3 T available to installer Warning This computer program is probected by copyright only law and international treaties Unauthorized reproduction or distribution of this program or any portion of it may result in severe civil and criminal penalties and will be prosecuted M Version List of all software versions in the projector Touch Panel Main Touch Panel Language English Touch Panel G5 System Supervisor Main Read only Swe SuOerisor Rant 15 25 51 Figure 3 7 About Menu The About menu lists which versions of critical components are installed in the projector As shown in Figure 3 7 this is a read only menu for all users and includes a button for installers service to exit TPC software entirely and return to Windows 3 18 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation Understanding Versions in Your Projector Consult the About menu to determine the current level of a hardware or software component installed in your projector Upgrading any of these components requires a qualified Christie service technician TOUCH PANEL Indicates the software functionality of the Touch Panel Controller TPC its menu language and identifies its main operating system SSM Indicates which System Supervisor Module is installed H W and what SSM software is present Main and Boot portions ENGINE Indicates the main processing software in the projector This
186. le through available test patterns To return to a presentation toggle the Test Pattern button again or select one of the 32 channel buttons NOTES 1 Allow 2 3 seconds for each test pattern to appear 2 The number and type of available test patterns depends on what the installer loaded during installation 3 Any user beyond the General User can also choose from the complete range of test patterns offered in the password protected Advanced menu START FEATURES OR PRESENTATIONS To start a different feature or presentation press its corresponding channel button STATUS BUTTON Color indicators Green All OK Yellow Environment Diagnostics WARNING Red Environment Diagnostics CRITICAL ERROR Flashing ALARM CONDITION CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation Intelligent Lens System ILS The Main Lens menu is used to adjust the Focus Horizontal X and Vertical Y Offset and Zoom of the lens See Figure 3 4 All settings on this screen are in real time This menu also enables you to manually override the intelligent lens system settings When the channels are changed the ILS automatically moves the lens to adjust the Focus Horizontal X and Vertical Y Offset and Zoom based on the pre defined settings Using the Emergency Override knobs on the lens mount to adjust these positions does not save the settings to the channel They are designed for temporary emergency use therefore ho
187. legal support of copyright and they may also be components of copy control schemes WHITE BALANCE The color temperature of white used by the projector WHITE FIELD The area of an image that is white only For example a full white field is an image that is white everywhere A 10 white field is a white area usually rectangular that occupies 10 of the image the remaining 90 is black YCBCR A high end digital component video signal YPBPR A high end analog component video signal Sometimes called YUV Component or Y R Y B Y the YPbPr signal by passes video decoding YUV Refer to YPbPr ZOOM The adjustment of image size by means of a zoom lens A 14 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE Appendix B ASCII Messages Use the following ASCII messages function codes for remote communications with the TPC and its corresponding projector All messages must be sent via Ethernet NOTE Please refer back to Section 3 6 Remote Control of the Touch Panel Controller for a complete explanation of remote communica tions setup message protocol and format e B 1 Function Codes B 2 Messages with Multiple Parameters CP2000 XB User Manual B 1 020 100163 04 Rev 1 06 2009 Appendix B ASCII Messages CH IS TIE l B 1 Function Codes Table B 1 Function Codes Function Code Examples Description and Parameters Anamorphic Lens AML AML 0 or AML 1 Move the anamorphic lens out 0 or in
188. len keys CP2000 XB User Manual Lamp Ballast 3 phase 7 kW for all lamps in all countries Choice of lamp kit incl protective gear Cable kit incl two lamp power cables and two communication control cables Extractor Kit 50 60 Hz Choice of lens Auxiliary lens and mount are both optional Lamp Ballasts P N Ballast Cable Kits P N 2 meters 6 ft 38 814003 51 7 5 meters 25 ft 38 8 14004 51 15 meters 50 ft 38 814005 51 30 meters 100 ft 38 814006 5 1 Other P N FredFrame Rigging Frame 38 8 14007 51 Extra Heat Extractor Kit 50 60 Hz 38 814008 51 Side Venting Duct Adapter Kit required for stacked projectors 108 100101 01 F Aperture Kit set of 4 38 813028 51 Protective Clothing Kit for opening of lamp door 598900 095 Ore 10 bit Librarian Setup Software ee CHRISTIE CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE Appendix A Glossary This appendix defines the specific terms used in this manual as they apply to this projector Also included are other general terms commonly used in the projection industry CP2000 XB User Manual A 1 020 100163 04 Rev 1 06 2009 Appendix A Glossary CH IS TIE l 3 2 PULL DOWN A frame sequence used to map 24 fps film to 30 fps video or 24 1 001 to 30 1 001 fps in which every second film frame is represented by three video fields instead of two the third being a repeat of the second This leads to a set of ten video fields for each four
189. length Side borders both slant in or out producing a keyhole shaped image It is caused when the lens surface is not parallel to the screen LAMPLOC A Christie software feature where samples of output light from a projector guide the precise position of the lamp along 3 axes vertical horizontal and distance to lens so that lamp performance and output is maximized CP2000 XB User Manual A 7 020 100163 04 Rev 1 06 2009 Appendix A Glossary CH IS TIE l LIFE SAFETY A safety control system integrated into the HVAC fire alarm and other infrastructure components of the theatre as well as the presentation system Comment In the event of a fire for example the life safety system may turn on the auditorium lighting to full intensity cancel the presentation audio and replace it with a PA microphone or pre recorded announcement turn the lamp OFF flash warning lights and so forth Every jurisdiction may have different statutory requirements for life safety systems LINEARITY The reproduction of the horizontal and vertical size of characters and or shapes over the entire screen LINE OF BEST VIEWING When light from a projector is incident on a screen the light reflects from the screen such that the angle of reflection equals the angle of incidence The Line of Best Viewing is along the line of reflection LITELOC A Christie software feature where samples of output light from a projector trigger automatic adjustments in
190. les to raise and or suspend this assembly If desired the lamp ballast can also be hoisted and flown from its integral rigging bars Follow the instructions provided with the FredFrame kit Warning 1 Use straps and or cabling with load capacity adequate for the total projection head frame weight 2 Remove the lens before hoisting NOTE Never exceed the Load Rating specified in the FredFrame Stacking amp Rigging Kit instructions Critical safety Refer to the complete instructions for using the FredFrame These include all installation instructions as well as mechanical adjustment procedures for proper image alignment Stacking To stack two projection heads together you must first secure each head within a FredFrame then secure all corners of the frames together using 4 stacking pins provided in the FredFrame kit You must also use the Side Venting Exhaust Adapter to route exhaust air from the bottom projector away from the top projector not required with a side by side projector row Never stack more than 2 projection heads together and do not attempt to move stacked projectors without proper transport equipment CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 2 Installation amp Setup 2 4 2 4 1 2 4 2 Installing a Lens Lamp and Cooling Before or after you have positioned the projector in its permanent or temporary location install the remaining components the lens lamp and
191. lize and instead displays a communication error such as No connection or Cannot locate Ethernet port or Waiting to Connect there is likely a bad connection or address between the TPC and the rest of the projector Check that TPC cabling is intact and try again Review Section 7 Troubleshooting and if the problem persists contact your network administrator CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation 3 5 Using the Touch Panel Controller Touch Panel Controller software resembles other Windows based applications but is activated by touching locations on the TPC screen itself Touch large raised rectangular buttons to activate a function such as turning the lamp or shutter ON or OFF or to start a presentation or select a different icon Buttons may include text and or an icon e To log on off as a different user touch the user icon in the bottom right corner e To go to a new menu touch its tab at the top of the page e To go to a submenu touch its tab located above the status bar e To see more options in pull down menus touch 0 e To select an option in a list touch the option text e To begin entering text such as serial numbers touch the entry box e To escape without change from a pull down list touch menu background e Leaving a menu automatically saves its current settings Touch checkboxes to toggle ON or OFF e Touch O to jump to the Status menu at any time All TPC menu
192. log or digital of most computers Analog RGB video can have 3 4 or 5 wires one each for red green and blue and either none one or two for sync For three wire RGB the green wire usually provides sync Refer to TTL Video RS 232 A common asynchronous data transmission standard recommended by the Electronics Industries Association EIA Also called serial communication RS 422 A less common asynchronous data transmission standard in which balanced differential voltage is specified RS 422 is especially suited to long distances S VIDEO The output from certain video tape players and video equipment S Video separates sync and luminance from color information typically producing a higher quality display than composite video Also known as Y C SCAN FREQUENCY The horizontal or vertical frequency at which images are generated Also known as scan rate or refresh rate SCAN LINE One horizontal line on the display SECAM A video output format of some video tape and disc players used primarily in France SECAM Sequential Couleur M moire signals are similar in resolution and frequency to PAL signals The primary difference between the two standards is in the way color information is encoded CP2000 XB User Manual A 11 020 100163 04 Rev 1 06 2009 Appendix A Glossary CH IS TIE l SHOW SCRIPT A small file consisting of automation cues in addition to a play list triggering theatre events action data and possibly in
193. messages if the problem is not fixed In these cases the 8 in the original System Warning code will change to a 0 Refer to Table B 3 Table B 5 P4 Codes INCLUDED WITH SYSTEM WARNING ERROR MESSAGES ONLY Examples P4 Meaning 1500 or lower Fan speed is 1500 RPM Speed must be 1501 RPM or higher 056 always C Temperature is 56 Cool to within ranges shown in Table 3 1 on page 13 00001 There is no P4 data for this type of error Examples of System Warning 002 Error Messages 65535 01002 ERR 002 System Warning 8010 00051 Prism Temperature Warning 65535 01002 ERR 002 System Warning 8020 00001 Lamp Life Expired 65535 01002 ERR 002 System Warning 8032 00001 SSM Read Failed CP2000 XB User Manual B 17 020 100163 04 Rev 1 06 2009 Appendix B ASCII Messages B 2 2 For Your Information FYI FYI messages are generated and broadcast when an overall change in the projector s status 1s detected Each FYI message identifies the IP address of the TPC generating the message followed by a code for the change as well as one or more parameters of descriptive details about what has changed NOTES 1 Because FYI messages are gated by the Error Message Enable EME control disabling serial error message also disables FYI messages 2 FYI messages do not occur unless there is a Cine IPM present B 2 3 History HIS A number of lamp histories are stored in memory with the oldest discarde
194. mpressed air Fold a microfibre cloth smooth and gently wipe remaining dust particles off the lens Make sure to wipe evenly with the smooth portion of the cloth that has no folds or creases Do not apply pressure with your fingers use the tension in the folded cloth itself to collect the dust If significant dust is still bound to the surface dampen a clean microfibre cloth with lens cleaning solution damp not dripping Wipe gently until clean IF FINGERPRINTS SMUDGES OIL 1 Brush most of the dust off with a camel hair brush and or blow dust away with compressed air 2 Rolla lens tissue around a swab and soak in lens cleaning solution Tissue should be damp but not dripping 3 Gently wipe the surface using a figure 8 motion Repeat until blemish is removed Cleaning the Reflector IF DUSTY Brush most of the dust off with a camel hair brush and or blow dust away with compressed air 4 Ifsome dust remains just leave as is air circulating at the lamp is unfiltered so some dust 1s inevitable Avoid unnecessary cleaning IF FINGERPRINTS SMUDGES OIL 1 First brush dust off with a camel hair brush and or blow dust away with compressed air 2 Fold a clean microfibre cloth and dampen with methanol Make sure to wipe evenly with the smooth portion of the cloth that has no folds or creases Do not apply pressure with your fingers use the solution in the cloth to collect the dirt Other Components In a normal operating en
195. must include 3 2 pull down encoding and Ancillary Time code information e Signal must include 2 2 pull down encoding and assumes field one 1 dominance Same as Prog Seg mented Frame e Image will be centered vertically on screen default Keep in mind that the projector will attempt to automatically adapt to any incoming data format that does not exceed either the bandwidth of the system or the frame rate limitations thus formats beyond those shown above may be compatible 4 2 Image Formats The two standard types of cinema displays flat and scope differ in their width to height aspect ratio as shown below Flat Image Scope Image Aspect ratio 1 85 Aspect ratio 2 39 Figure 4 2 Standard Cinema Formats Achieving either of these displays from a wide variety of incoming source material depends on proper settings in the projector as well as certain theatre conditions CP2000 XB User Manual 4 3 020 100163 04 Rev 1 06 2009 Section 4 Cinema Operation CHix IS TIE l 4 2 1 4 2 2 4 4 Projector Variables Electronic and Anamorphic Resizing Because the native resolution format of this projector closely matches the flat aspect ratio the native resolution being only slightly wider at 1 89 the projector can essentially show incoming flat images through its standard zoom lens Scope source material however is typically squeezed electronically that is it is distorted into a narrow image
196. n within the applicable boundary of the installed lens NOTE When adjusting the Focus Offset and Zoom you may experience a slight delay in the response rate of the lens upon selecting the buttons l Ensure Auto ILS is selected from the Main Lens menu NOTE Enabling Auto ILS will over write the pre defined settings for this channel To CH25 32 tensf perform a temporary lens adjustment uncheck J Auto ILS and adjust the lens by clicking the necessary buttons or manually adjusting the focus offset and or zoom knobs All temporary adjustments will be lost when Auto ILS is selected again or if the channel changes Figure 2 34 Intelligent Lens System Using a DC2K Framing test pattern DC2KFraming tga is recommended adjust the Offset by clicking the up down left right buttons on the Main Lens menu Figure 2 34 as necessary to display a square image on the screen NOTES 1 You can also hold the buttons down for continuous movement 2 For best optical performance make sure to minimize keystone error by using offset more than aiming to center the image in off axis installations 3 For best results avoid extreme tilts or offsets Corner vignettes on a white test pattern indicates extreme offset that should be avoided using mechanical alignment The maximum vertical offset is shown in Figure 2 35 bottom illustration NOTES 1 Horizontal offset is just a few dozen pixels resulting in a maximum of 52 of the image displayed on on
197. n Size Screen size image size may be up to 145 feet across depending on your lens and ambient light level Choose a screen size appropriate for your lens and application Keep in mind that if the projector will be used to display much text information the image size must allow the audience to recognize all text clearly The eye usually sees a letter clearly if eye to text distance is less than 150 times the height of the letter In other words small text that is simply located too far from the eye will be illegible no matter how sharply and clearly it is displayed NOTE Screens images are most described according to their horizontal gt screen width Aspect ratio is also specified if it is anything other than 4 3 see below The older diagonal screen size typically used for 4 3 displays such as televisions and monitors is less commonly used for large projection screens Table 2 1 Matching Lenses to Screen Size Lens Type Screen Width Screen Aspect Ratio Aspect ratio describes the proportion of the display and is expressed as the ratio of width to height such as 5 4 or 16 9 Typical aspect ratios range from 1 25 to 2 35 the higher the value the wider or less square the image See Table 2 2 Table 2 2 Typical Aspect Ratios Application Aspect Ratio 1256 35mm filmstrip 1 32 4 3 NTSC Video KGA 1 33 4 3 Cinemascope CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 2 Installation amp Setu
198. n be deleted only by using Christies licensed DCP Librarian software Important Create MCGD is a permanent over write of any previous MCGD OnSite file and will define new default color processing in the projector TARGET TCGD and CREATE TCGD NOTES Upon opening the Gamut menu the Target TCGD color fields show the corresponding x y color coordinates defined for the current target color gamut in use You can create a new custom target by defining different coordinates for one or more TCGD colors or simply by changing the tolerance state and saving as a new TCGD file Note however that industry defined TCGD standards such as P7v2 and others are write protected and cannot be changed modifications to such a target must be saved under a new TCGD filename entirely Once you have created a new TCGD file it will appear in the Custom menu where it can be selected for use in the display NOTE For most applications TCGD values are used simply to verify that displayed colors actually do match the standard i e you can measure each color at the screen and compare its coordinates to those appearing in the TCGD fields to confirm that the projected colors are accurate For special applications in which you want to create a unique target color standard enter new TCGD coordinates as desired and then save as anew TCGD file Apply as usual from the Custom menu GAIN NOTES Gain indicates the luminance a k a brightness or intensity of each color
199. n front of the primary lens to widen a squeezed image into a properly proportioned scope auxiliary cinema display It is typically used in theatres having side masks that are retracted for scope images or in theatres having fixed side masking but a very short throw ratio throw ratio throw distance screen width Refer to Section 2 12 Offset and Boresight Alignment for all lens installation and boresight instructions Refer to Section Custom Lens Menu on page 3 27 for ILS and channel setup Lens Mount Functions 1 If the Motorized Auxiliary Lens Mount MALM is present ensure to move the MALM to the OUT position before performing any lens calibrate or reset functions on the Motorized Primary Lens Mount to prevent collision between the projection lens and the MALM 2 Hazardous moving parts Keep fingers and other body parts away patis NOTES 1 Projector must be fully assembled and powered up in its final location 2 Keep clear of rotating parts Remotely operated motors may start to spin without warning 3 Avoid long hair jewelry and loose clothing exposure to the knobs during manual adjustment 4 In case of emergency unplug the line cord to immediately halt movement of the lens mount 5 When adjusting the Focus Offset and Zoom you may experience a slight delay in the response rate of the lens upon selecting the buttons Offsets From the Main Lens menu click the up down left right buttons as necessary to adjust the image
200. ncies within a specified range VERTICAL FREQUENCY The frequency at which images are generated Vertical frequencies vary amongst sources Also known as vertical scan rate VERTICAL OFFSET The difference between the center of the projected image and the center of the projector lens For this projector this value is expressed as the maximum percentage of the image that can be projected above or below the lens center without degrading the image quality All CP2000 XB lenses have the same vertical offset range VESA The Video Electronic Standards Association establishes standards of communication between electronic components to help ensure universal compatibility VIDEO The signal that is used by display devices such as projectors to generate an image This term also refers to the output of video tape disk players and computers VIDEO STANDARD A specific type of video signal such as NTSC PAL SECAM VIEWING ANGLE Screens do not reflect equally in all directions Instead most light is reflected in a conical volume centered around the line of best viewing Maximum brightness is perceived if you are within the viewing cone defined by the horizontal and vertical viewing angles CP2000 XB User Manual A 13 020 100163 04 Rev 1 06 2009 Appendix A Glossary CH IS TIE l WATERMARK Data embedded in essence that serve different purposes and that are either imperceptible or obvious robust or fragile Their usual purpose is for
201. ncy is achieved by creating a variety of source files in projector memory each of which indicates the following for the projector e Incoming Resolution pixels across pixels top to bottom e Offset desired 1 e amount of data to discard Rare e Desired Aspect Ratio 1 e the original display format to be recovered Although in rare cases the content distributor may include this source information as part of a pre defined PCF applied by using the PCF in the projector alternatively these variables can be defined either in the Source submenu in the TPC as described here or by using DCP Librarian With a good collection of assorted source files available in memory the proper file can then be quickly chosen from within the Custom menu for implementation in the projector whenever a matching input signal is encountered NOTE For any source the projector relies on Source file settings as well as Screen file settings See also Admin Screen menu CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE i Section 3 Operation Main Status Custom Advanced Admin About SOUrce Width to height image proportion Incoming Format z desired Amount to discard value will discard data from top and or left value will discard from bottom and right Adjust x y resolution and off set as desired Test in display without saving Save settings in a source
202. nd vertically stretched via 3 d_party software 7 6 7 Data is Cropped from Edges CAUSE REMEDY 1 To display the missing material reduce image size to fill the display area available in the projector then stretch vertically to fill the screen from top to bottom Add the auxiliary lens to regain the image width 7 6 8 Display Quality Appears to Drift from Good to Bad Bad to Good CAUSE REMEDY 1 The source input signal may be of low quality 2 The H or V frequency of the input may have changed at the source end 7 6 9 The Display has Suddenly Frozen CAUSE REMEDY If the screen blacks out inexplicably it is possible that excessive voltage noise on the AC or ground input has interrupted the projector s ability to lock on to a signal Power down the projector refer to Section 3 3 Power Down Procedure and unplug Then plug in again and power up as usual refer to Section 3 2 Power Up Procedure 7 6 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE Section 7 Troubleshooting 7 6 10 Colors in the Display are Inaccurate CAUSE REMEDY 1 The color tint color space and or color temperature settings may require adjustment at your input source 2 Make sure you are using the proper PCF TCGD and or CSC file for this source 7 6 11 The Display is Not Rectangular CAUSE REMEDY 1 Check leveling of the projector Make sure that the lens surface and screen are parallel to one another 2 Is the vertical off
203. ne reference settings will be lost once the channel changes If used click Lens Reset from the Advanced Lens menu to ensure ILS settings are properly recalled Proper adjustments should be made in the Custom Lens menu when time permits When ILS is enabled Auto ILS is checked and the channel has been specified each motor begins adjusting The proper lens type must be selected from the Advanced Lens menu beforehand The position of each motor is then saved onto the system in the specific channel file This is not a global feature instead it is controlled on a per channel basis When this feature is enabled the ILS for the currently selected channel is turned ON NOTES 1 Only Advanced users can modify channel settings 2 Keep clear of rotating parts Remotely operated motors may start to spin without warning 3 In case of emergency unplug the line cord to immediately halt movement of the lens mount To Enable ILS Per Channel 1 Select the Main Lens tab Figure 3 4 2 Select Auto ILS to automatically apply the per channel settings To Edit Active Channel ILS Settings 1 Ensure Auto ILS is checked ao a 2 Adjust the Focus Horizontal X and Vertical Y Offset or Zoom one step at a time by clicking the z l applicable button or hold the button down for CH 1 8 CH 3 16 CH 17 24 CH 25 32 Lens continuous movement NOTE This over writes the ia 11 11 06 Ei intelligent lens system settings Figure 3 4 Intelligent Lens System
204. nector nut located in the rear of the lamp compartment and screw in fully Figure 6 1 left Hand tighten only Important Handle by the cathode anode end shafts only never the glass Do not over tighten Do not stress the glass Wer Anode A Connector r Do m Ahan A A Screw bulb i Wr into connector Wo A Reflector Lamp Cradle Figure 6 1 Install Bulb 2 Rest the anode end of the lamp on the lamp cradle as shown in Figure 6 1 right and slip the positive lamp connector over the bulb end 3 Tighten setscrews in both negative and positive lamp connectors Figure 6 2 Secure anode connector 6 N A A gt p A Secure cathode connector Reflector Figure 6 2 Secure Bulb at Cathode and Anode Connectors Important Proper electrical contact prevents resistance in the lamp connectors If you accidentally touch the quartz body of the lamp with your bare hands clean it as described in Section 6 3 Maintenance and Cleaning CP2000 XB User Manual 6 9 020 100163 04 Rev 1 06 2009 Section 6 Maintenance CH IS TIE l STEP 9 Check Leads Make sure that the anode lead between lamp and igniter is well away from any projector metal such as the reflector or firewall Warning Leads too close to metal parts will cause arcing during starting pulse This is a SAFETY HAZARD and the lamp may not ignite S
205. nge to indicate a warning yellow or critical error red status which triggers the same warning light on the status bar and at the main PROJ STATUS light on the rear of the projection head e Yellow Warning indicates an unusual environmental condition For example a temperature may be ele vated and nearing its upper limit correct the problem by checking all cooling systems turning off the projector and cooling if necessary make sure to follow the standard shut down procedure Service may be required in some cases e Red Error indicates that 1 the environment has a serious problem or 2 a specific electrical component is not detected or does not appear to be functioning properly In some cases a module may need re seating In other cases service or replacement of a module may be required before the projector can resume normal operation Regardless a red indicator requires immediate attention e Diagnostics showing a question mark icon indicate an unknown status caused by a problem during initialization Try re booting the projector In addition a full screen flashing red alarm window appears on the TPC for failed interlocks mandatory over temperature optional and fan problems optional 3 12 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE Section 3 Operation Main Status Custom Advanced Admin About Description Value i Po coved 4 Current 69 4 ol Voltage P14 Bl Pow
206. not shown is also required for the IR emitter or polarizing cell 3 Refer to Figure C 2 Circuit for Power Supply on page C 3 for cabling details CP2000 X AT Cinema Media Server GPO SYNC IR Emitter Active glasses Or polarizing cell for Z screen passive glasses Figure 3 55 Typical Dual Input 3D System SHOWN WITH ACTIVE GLASSES CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE 3 10 4 Other Hardware Setups Section 3 Operation Other expected hardware configurations with a single 3D source input are shown in Figure 3 56 NOTE For future reference Single 3D input is not currently supported CP2000 X GPO SYNC IR Emitter Active ee ef oe GPI SYNC glasses 0r polarizing cell for Z screen passive lasses HD SDI PRR CP2000 X GPO SYNC IR Emitter Active glasses Vor polarizing cell for Z screen passive HD SDI i glasses Sync embedded with image data Figure 3 56 Single Input 3D Systems currently not supported CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 3 67 Section 3 Operation CHRISTIE 3 10 5 3D Instructions 3 68 NOTES 1 Assumes a full 2048 x 1080 display and 3D enabled in the Custom 3D Control menu 2 3D stereo sync or reference signal is part of input
207. ns listed in Table B 1 you can determine the parameter s range with the request message ASCIICODE M For example LPL M What is the minimum and maximum lamp limit LPL M000 5000 Minimum lamp limit 0 maximum lamp limit 5000 If a function code has multiple parameters Refer to Section B 2 Messages with Multiple Parameters below their ranges cannot be requested B 14 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix B ASCII Messages B 2 B 2 1 Messages with Multiple Parameters Certain messages are more complex and require multiple parameters in order to relay complete information These messages are described in detail below Error Messages ERR An error message is generated by the projector TPC and contains a numerical error code a message specifier 1 e type of error such as System Error and a text explanation of the error In addition System Error and System Warning error messages also include further explanation of the nature of the error such as its location and cause NOTE The type of error and text parameters are enclosed together in quotation marks separated by a colon and space In the table below the text explanation appears as l Table B 2 Error Messages Error Code P1 Type of Error P2 be a e ons sowe dows oters Thesousebiswong mf eereeet E deren command it is ignored and no error is returned Additional Parameters for
208. nsult the Cine IPM 2K User Manual for details Selecting the Source For any display the projector interprets incoming signal data according to one of 32 user selectable display files defined at the time of installation and or with each subsequent release of a new digital cinema feature and stored in projector memory Each file is essentially a collection of processing display settings optimized for a particular cinema feature or alternative non cinema content enabling consistent presentations with minimum further adjustment Each file is represented by an assigned channel button selectable over several pages of the TPC Main menu Depending on your installation you may have 0 32 different non cinema sources defined for use TO SELECT A NON CINEMA SOURCE With a non cinema source connected to the CP2000 XB use the Main menu on the Touch Panel Controller to select the channel button representing the desired non cinema source Once selected the button will darken and the projected display will change according to the corresponding file settings Refer to Section 3 5 Using the Touch Panel Controller if you need help TO RETURN TO A CINEMA SOURCE At the Main menu of the Zouch Panel Controller select one of the cinema channel buttons pre configured for a cinema source input at port A or B the CP2000 XB will now ignore the DVI ports and respond to the cinema source activated by this button CP2000 XB User Manual 5 3 020 100163 04 Rev 1 06 2009
209. o SMPTE 292M cinema inputs used individually or simultaneously for high speed dual link processing and each supporting CineLink local link encryption Dual DVI Digital Visual Interface connectors for alternative non cinema content used individually or simultaneously for high speed dual link processing Can be rigged flown and or stacked with adjustable FredFrame rigging hardware Choice of 4 Xenon bubble lamp sizes and ratings Universal 3 phase 7 kW switching ballast for all lamps and countries Screen brightness Up to 14 fL on 90 ft screen Achievable contrast ratio 2000 1 full field on off in center LampLOC motorized lamp alignment automatic or custom bulb positioning LiteLOC for maintaining brightness over time Simple single button Start Feature function via Touch Panel Controller CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE i Section 1 Introduction 1 1 3 Auto detection of a variety of SMPTE 292M input formats incoming interlaced formats require proper 3 2 or 2 2 pull down time code Internal douser shutter for quick picture muting and cool stand by mode Bit depth of 45 bits 35 2 trillion colors New ruggedized lens mount that accepts the new High Brightness HB lenses as well as previously avail able High Contrast HC lenses Choice of High Brightness and High Contrast zoom lenses from 1 25 1 up to 8 5 1 Optional Motorized Auxiliary Lens Mount for 1 25x anamorphic or 1 26x
210. od or bad signal Current channel 101 132 Current vertical frequency 0 OK 1 Unexpected lamp OFF 2 Lamp failed to ignite C Ca C aC C a G Shows caution or critical Shows caution or critical Shows caution or critical Shows caution or critical Shows caution or critical Shows caution or critical Shows caution or critical 0 OK open 0 OK 1 open 0 OK 1 open 0 OK 1 open 0 OK open RPM Also indicates slow or failed condition CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix B ASCII Messages P1 Notes IfP1 4 0 Touch Panel Main Indicates version detected in Versions 1 Touch Panel Language projector 2 Touch Panel Operating System 3 System Supervisor Module Main 4 System Supervisor Module Boot 5 System Supervisor Module HW 6 Ballast Interface SW 7 Ballast Interface HW 8 ILS Main 9 ILS Boot 10 ILS HW 20 Engine 21 Interface ARM Boot 22 Interface ARM Main 23 Interface FPGA 24 Interface PIC 25 Processor DSP Boot 26 Processor DSP Main 27 Processor DSP Diag 28 Processor DSP FPGA 29 Formatter Interface Hitachi 30 Formatter Interface FPGA 31 Formatter Interface PROM 34 EFIB Main 35 EFIB FPGA 36 EFIB Boot 37 EFIB Sequence 40 Formatter Red Boot 41 Formatter Red Main 42 Formatter Red Config 43 Formatter
211. of measure are shown above the light output bar 3 Enable LiteLOC As the lamp ages and loses efficiency the projector will gradually and automatically supply more current to the lamp as necessary to maintain your chosen level of light output for as long as possible the light level is read from an internal light sensor 4 To change your LiteLOC setting adjust the Lamp Power as desired and then press Set The LiteLOC function will automatically begin to maintain this new setting WHEN SHOULD I USE LiteLOC Typically most theatre installations would use LiteLOC for daily operation since it need only be set once for each lamp install and ensures consistent worry free brightness at the screen for as long as possible If desired reset LiteLOC to a different level at any time or override with a specific lamp power setting 3 58 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation HOW LONG CAN I MAINTAIN BRIGHTNESS Software can maintain a LiteLOC setting until the required power exceeds the maximum rating for the lamp 2 0 3 0 4 5 or 6 0 kW by approximately 10 The lower your LiteLOC setting the longer it will take to reach this over drive threshold and the longer you can maintain the desired brightness Tan N A e safely driven at no more than watts teLoc Lame i To produce 14 fL at the screen a new lamp nab ae aga iis would likely need less than this maxim
212. omplex Look up Table No information available Pull Down Sequence Identifies sets the frame sequence to achieve a target frequency or time relationship with another signal Pull Down Offset Identifies sets the frame offset SMPTE Field Bit Identifies sets offset polarity CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation Custom 3D Control Menu Custom 3D Control menu provides numerous controls for adjusting and synchronizing incoming 3D signals always dual L R HD SDI signals at the SMPTE A and B ports with each other and with external 3D equipment such as screens emitters and glasses Custom 3D Control menu options are summarized in Figure 3 11 and Table 3 6 Add a check in the Enable checkbox in order to 1 enable 3D display and adjustment parameters 2 automatically configure the nput and Data Format on the Custom Page 1 menu For full 3D application notes including a step by step tutorial for use refer to Section 3 10 Working with 3D Enable 3D Test Pattern Toggle 3D function ON OFF Custom Advanced Admin About mEt mlO Sets frame rate per signals a w Enable Test Frame Pate 4 2 Ex 4 frames 2 signals Defines source amp 3D sync input LiF Input Reference Sets which GPI to use Use 1 type Input PI None 7 if external server is supply Active Pork ANE LIR ing separate 3D sync at GPIO Frame order For cor
213. ose levels with rights that are equal to or lesser than those of the current login will appear Enter a new 1 8 character password for the current login or when adding a new user Non editable at other times Confirm PW Re enter the 1 8 character password entered in Password box Editable when changing the current password or when adding a user Change PW Change the password for the current login Change Level Change the rights for a different user having the same or fewer rights as the current login Add User Activates the editing box for defining a new user their rights and password You cannot define more rights than your own Delete User Delete a different user who has the same or fewer rights as the current login and who is currently displayed in the User Name box The current login user cannot be deleted Escape to the original User Menu without saving changes Record current User Menu settings in TPC memory CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE To add a new user l m a a Press Add User Enter desired User Name Enter a Password Re enter the new password in the Confirm PW box Press Save To delete a user l 2 3 Select the desired User Name from the User Name list cannot be current login Press Delete User Press Save To change a user s rights User Level l 2 3 4 Select the User Name you wish to modify cannot be current login Press Change Level but
214. output level chosen for LiteLOC Same intensity for every channel requires LPB Lamp Per Button set to OFF NOTE Specify desired channel with S If no S parameter is included the LPI setting will apply to the current channel when the Lamp Per Channel checkbox is enabled and to all channels when the checkbox is cleared LPI What is the current LiteLOC setting for this channel LPI s101 What is the LiteLOC setting for Channel 101 LP1 12345 The current LiteLOC setting is 12345 CP2000 XB User Manual B 7 020 100163 04 Rev 1 06 2009 Appendix B ASCII Messages CH IS TIE l Function Code Examples Description and Parameters LampLOC Module LLM LLM000 000 0158 Single Parameter 1 Calibrate stepper motors 2 Automatic Lamp alignment LampLOC Multiple Parameter P1 0 move motor P2 0 1 2 specifies either x y or z motor respectively P3 Destination new motor position 200 up to 200 Lamp Message Enable LME LME 0 Enables or disables a lamp timer message when the lamp has LME 1 exceeded its expected life 0 No lamp message will appear when lamp limit expires 1 Lamp message will appear when lamp limit expires Lamp Mode LPM 2 Constant power 3 Constant light intensity LiteLOC mode NOTES 1 Specify desired channel with S Ifno S parameter is included the LPM setting will apply to the current channel when the Lamp Per Chann
215. overlap precisely to form pure white lines throughout the image one or more poorly converged individual colors may appear adjacent to some or all of the lines Qualified service technicians can correct as described on the color label provided inside the projection head NOTE Custom Convergence Kit required available separately FOLD MIRROR ADJUSTMENT If a corner or edge of the image is missing this may indicate that the fold mirror has become misaligned with the rest of the optical system resulting in cropping of data Correct as described below O Locate the fold mirror access plate secured to the underside of the projection head just below the lens It has 2 access holes along the front edge through which you can carefully adjust the fold mirror SCrews e To raise or lower the image adjust the screw closest to the left side exhaust side of projector e To move the image left or right adjust the screw closest to the right side lamp side Figure 2 42 Fold Mirror Adjustment l Shadow from Proper fold mirror adjustment is shown at right with the whole image integrator edge well centered between the projected edges of the integrator NOTE Use full white test pattern oo ee E Active pixels Figure 2 43 Proper Fold Mirror Adjustment 2 30 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 2 Installation amp Setup 2 14 Calibrating the CP2000 XB System NOTE DCP Librarian described here is l
216. p Although image size and aspect ratio can be adjusted using projector controls it is still ideal to use a screen with an aspect ratio that closely matches your likely source material You can then more easily fill the screen with the image without restricting either image size or content For example standard video from a VCR has a 4 3 ratio approximately and can fill a 4 3 screen without side to side stretching whereas a high definition signal with a 16 9 aspect ratio is largest on a 16 9 screen Screen edge Screen edge Ne Image edge Image edge 16 9 screen 5 4 screen Figure 2 8 Aspect Ratios Images vs Screens As shown in Figure 2 8 an obvious mismatch between source material and screen is characterized by black bars on both sides of the image if the screen is wider than the source material or above and below the image if the source material is wider typically called a letter box display The black bars are unused display pixels and in many installations such as theatres are masked or hidden behind panels or curtains Alternatively if the area of unused pixels is considered minimal you may prefer to use the projector s software control to slightly stretch the image either horizontally or vertically enough to utilize the remaining pixels while not noticeably distorting the image Displaying Both Flat and Scope As an example two standard types of displays common in theatres flat and scope differ
217. p through purposes NOTE Not for use with Christie s Cine IPM 2K Use RS232 B only e ETHERNET A or B For Ethernet communications to and from compatible network equipment such as a cinema server or PC This enables remote control of the projector via an Ethernet based network These ports are identical to one another e HD SDI A or B Connect a wide variety of high definition cinema sources servers to these SMPTE 292M bit serial standard interface BNCs These ports are identical to one another e TPC For connecting the Zouch Panel Controller e VOLTMETER During operation this window displays the number of AC volts reaching the projector Monitor regularly to ensure the display reads within the acceptable nominal AC range 200 240 at all times If the window is dark this indicates that 1 the projection head is unplugged or 2 the projection head is not powered up or 3 inadequate excessive or faulty AC has automatically tripped opened the ballast breaker causing a shutdown e PROJ STATUS This large bright light indicates from a long distance the current operating state of the projector such as if it is turned OFF or running normally or has a critical problem requiring investigation It duplicates the status light appearing in the bottom left corner of the TPC e OFF Projection head is unplugged e Amber Warning of unusual environmental condition e Green Normal operation e Red Error preventing normal operation e AC INPU
218. parated by one space character e Data pertaining to a specific source other than the current source is preceded by the letter S the source number 1 e channel and a space This is similar to an extra parameter PO e Text parameters such as channel names are enclosed in double quotes following the data as in Name TEXT PARAMETERS Most data is simply a numerical value however some messages also require text For example a channel naming message typically includes a text based name after the channel number enclose this text in double quotation marks as in Tilt the Wagon Use all characters as desired except for the following special characters these require a 2 character combination as shown in Table 3 21 Table 3 21 Special Characters for Text If you want Enter this Description this C a 0x0A n New line if the text can be displayed on more than one line this will cause the next character to be displayed at the start of the line that follows the current one 3 6 3 Sample Messages and Their Meaning Table 3 22 Sample Messages Desired Action Message Description Get current Chan CHA Request by controller for current channel Chan reply from proj CHA 101 Reply from proj that current channel is 101 CP2000 XB User Manual 3 53 020 100163 04 Rev 1 06 2009 Section 3 Operation CHRISTIE 3 6 4 What is Actually Sent in a Message 3 6 5 3 6 6 3 54 Although you will send and re
219. play parameters CHANNEL LIST A list menu of previously defined channels available in projector memory CP2000 XB User Manual A 3 020 100163 04 Rev 1 06 2009 Appendix A Glossary CH IS TIE l CHANNEL NUMBER A number that uniquely identifies a specific channel retained in projector memory The projector via its TPC offers up to 32 channel choices over several Main menu pages CHECKBOX A menu item that indicates whether an option is currently in effect checked or not unchecked CHROMINANCE The signal representing the color information hue and saturation when the image is represented as separate chrominance and luminance Same as chroma CLEAN APERTURE The fraction of a motion picture frame image that is intended to be viewed by the audience The clean aperture is subjectively free of edge artifacts and lies within the screen area framed by curtains in a cinema Aspect ratio is often referenced to the clean aperture COLOR GAMUT The range of colors allowed in a specific system as defined within a triangular area located on the CIE color locus diagram whose corners are the three primaries of the system Same as color space COLOR SHIFT A change in the tint of a white field across an image COLOR TEMPERATURE The coloration reddish white bluish greenish etc of white in an image measured using the Kelvin degrees K temperature scale Higher temperatures output more light COMPONENT VIDEO Refer
220. pling clock indicated by the number of pixels per line PLAY LIST A small file or script typically created by the exhibitor or installer that specifies the sequence of presentation of programs including features and trailers PLAYOUT The equipment in a digital cinema theatre which delivers previously recorded signals in real time to the playback system The playout may also receive store and process these signals prior to delivering them POST PRODUCTION The phase in film making that occurs primarily after production ends its processes include picture editing sound effects editing and mixing ADR Foley titles and opticals dubbing and print mastering CGI and visual effects and scoring Post production culminates in acceptance of the original negative answer print Even though post production officially begins on the last day of principal photography post production facilities such as editing are utilized from very early in the production phase in order to save time PRODUCTION APERTURE The area in pixels for digital images that constitutes the entire motion picture frame image Compare active picture PROJECTOR TO SCREEN DISTANCE The distance between the projector s front feet centers and the screen Also known as Throw Distance PULL UP PULL DOWN Shifting the frequency sample rate or frame rate to as to achieve a target frequency or time relationship with another signal most commonly by 1 the ratio of NT
221. precautions in all installations 1 Never look directly into the projector lens or at the lamp The extremely high brightness can cause permanent eye damage 2 For protection from ultraviolet radiation keep all projector housings intact during operation Protective clothing and safety goggles are recommended NOTES 1 The American Conference of Governmental Industrial Hygienists ACGIH recommends occupational UV exposure for an amp hour day to be less than 0 1 microwatts per square centimeters of effective UV radiation An evaluation of your workplace is advised to assure employees are not exposed to cumulative radiation levels exceeding the government guidelines for your area 2 Be aware that some medications are known to increase one s sensitivity to UV radiation Nf 1 FIRE HAZARD Keep hands clothes and all combustible material at least 1m away from the concentrated light beam of the lamp 2 Position all cables where they cannot contact hot surfaces or be pulled or tripped over This projector must be operated in an environment that meets the operating range specifications in Section 6 3 Maintenance and Cleaning Warning Opening or removing a projector cover requires a qualified service technician CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE i Section 6 Maintenance 6 1 3 6 1 4 AC Power Precautions PAUNI Do not attempt operation if the AC supply is not within the specified voltage
222. r Installed Lens Reset On Startup Calibrate Lens Reset Select the type of lens installed using the drop down list If applicable select the type of auxiliary lens installed from the drop down list Enter serial number of lens installed Enables disables the Intelligent Lens System ILS NOTE Installed must be checked in order to use the ILS functionality Select this checkbox for the ILS to locate the sensor flags and the backlash of each motor at the same time Keep checked if you need to reset the lens often Click Calibrate to calculate the amount of backlash for each motor and make the necessary adjust ments to ensure proper motor range Calibration should only be used when changing lenses and is a necessary step at that time When Lens Reset is clicked the motors on the lens move to a central location mechanical center before moving back to the original position This feature is useful for initiating an auto lens reset CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation Advanced Test Pattern Menu In the Advanced Test Pattern menu use the double windows to organize and manage the master list of RGB test patterns Patterns in the top window are available to the user via the Test Pattern button on the Main menu of the TPC and will be displayed in the order of their appearance in this window The bottom window contains an alphabetical list of all remaining test patterns Toge
223. r server or an existing network connect the equipment to Ethernet A or Ethernet B Both ports route to the 5 port Ethernet hub connected to the projector s main processing electronics If Ethernet is not available at your site connect a standard serial cable to the RS232 port instead note this communication link is acceptable for using a PC laptop to run Christie s DCP_ Librarian or to download new software but 1s too slow for server communications and does not support ASCII messaging to the TPC which requires Ethernet CP2000 XB User Manual 2 21 020 100163 04 Rev 1 06 2009 Section 2 Installation amp Setup 2 7 2 7 1 2 7 2 2 22 Connecting the Ballast CHRISTIE Do not connect the ballast to AC unless the projection head and ballast are already connected to each other otherwise the exposed live ends of the heavy ballast cables could be a serious hazard Warning Connect the ballast to the projector FIRST and then connect to AC Configuring the Ballast for Incoming AC AC power levels vary from region to region throughout the world with 400 VAC common in some countries such as those in Europe and Asia and 200 VAC common elsewhere such as in North America and Japan To accommodate both possibilities the ballast includes an internal Jnput Power Range Switch for toggling to the level of AC available at the installation site i e either 200 or 400 VAC The line cord plug must also match From the factor
224. r site and installation requirements Warning Do not operate the projector without Christie Extractor components installed INSTALL DUCT ON PROJECTOR See Figure 2 23 Align either the 6 inch or 6 foot long duct at the projector s top exit port twisting to secure flaps over projector pins Confirm that 1 there are no obstructions or kinks within the ae E Twist to 4 secure ducting 2 all air intake areas of the projector are clear and exposed and 3 the vane switch at the exit duct moves freely 3 Add safety cable Connect to FredFrame or igniter door latch ADD EXTRACTOR See Figure 2 24 Connect the other end of the duct to the Christie heat extractor blower twisting to secure flaps over pins on the fan Make sure that the grille end of the fan faces down For longer exhaust runs at your site add extractors boosters as necessary the vane switch at the projector s top exit port will trigger a projector shutdown if the airflow is inadequate To prevent possible transfer of fan vibration to the image do not mount the extractor P directly on the projector include at least 6 of duct Warning Do not exceed Y align pins 6 ft duct length without adding additional extractors Extractor Fan atl To suspend the projector fan assembly always use appropriate rigging hardware and secure to adequate support structures at your site e The Christie 6 ft duct with fan weighs approximatel
225. range Do not allow anything to rest on the power cords Place the projector in a location where the cords cannot be abused by persons walking on them or objects rolling over them Never operate the projector if a power cable appears damaged in any way Do not overload power outlets and extension cords as this can result in fire or shock hazards Note that only qualified service technicians are permitted to open any enclosure on the product and only if AC has been fully disconnected from the projection head and ballast Warning SHOCK HAZARD Disconnect projection head and ballast from AC before opening any enclosure Lamp Precautions Xenon arc lamps are under high pressure and must be handled with great care at all times Lamps may explode if dropped or mishandled Wear Protective Clothing Never open the lamp door unless you are wearing authorized protective clothing such as that included in a Christie Protective Clothing Safety Kit P N 598900 095 Recommended protective clothing includes but may not be limited to protective gloves latex lab gloves double layer 0 040 acetate face shield and a quilted ballistic nylon jacket or a welder s jacket Warning EXPLOSION HAZARD Wear authorized protective clothing whenever the lamp door is open NOTES 1 Christie x protective clothing recommendations are subject to change 2 Any local or federal specifications take precedence over Christie recommendations Cool the Lamp Comple
226. re defined factory defaults for this channel Adjust or apply new settings as described in Section 3 Operation STEP 8 Adjust the Lens Turn the focus knob to sharpen the image Adjust the zoom ring on the lens to increase or decrease image size If desired use the horizontal and or vertical offset knobs to shift the image location For other lens functions refer to Section 2 12 Offset and Boresight Alignment and Section 3 9 Working with the Lens Installation Considerations Although the CP2000 XB is carefully engineered to deliver an exceptional quality high brightness high resolution output your final display results could still be compromised if the projector is improperly installed This subsection discusses issues to consider before proceeding with a permanent installation Read through to understand how good positioning will help ensure optimized images at any site Screen Types Front Screen Installations This projector is intended for use with flat or slightly curved screens front or rear ranging from about 5 meters 16 ft to 25 meters 82 ft wide Although flat screens generally offer a low gain similar to a matte white wall paint approximately 1 with a viewing angle just under 180 and are considered most effective when ambient light is low this difference in gain may be negligible given the very high light output from this projector In addition incident light reflects equally in all directions so the audience can s
227. rect L R Input Frame Dominance Display PI None Sets which GPI to use Use pairing amp smooth motion Left ILIRI Lon None only Left x Output GPO GPO1 e sets which GPO to use For Sets 3D sync input location r IF Display Reference synchronizing 3D stereo With source data Not Used Dark Time Adi b us peripherals such as emitter z or via GPI Mot Used screen etc 7 Sets time between L R A Sets 3D sync output True or euR Output Polarity Output Delay T J0 SE blanking time for glasses etc Inverted to close open True Output Delay P deg a ae i ey ae Shifts GPO pulse Pulse timing is shifted in relation to vertical Page 1 Page 2 30 Control Lame a frame 15 20 04 amp Shifts GPO pulse degrees Not used Figure 3 11 Custom 3D Control Menu Options Table 3 6 Summary of Custom 3D Control Menu Options CUSTOM 3D CONTROL MENU OPTIONS Enable Activate 3D controls and auto set Input to 292 Dual Input and Data Format to Unpacked 4 2 2 in the Custom Page 1 menu Test For confirming proper Sync Output setting 1 e which GPO is connected to your 3D peripherals such as emitters glasses etc L R Input Reference Defines how 3D stereo sync input is supplied currently ports A and B only See L R Input Reference Notes below Input Frame Dominance Defines frame order L R or R L required for 3D perspective Correct setting ensures smooth motions an
228. ronically logged and reported and 2 will immediately disable the current CineLink 2 cinema presentation The unlocked state is reported via a TPC alarm window serial communication and SNMP note the latter requires the TPC 60 model of the Zouch Panel Controller new in 2006 You must lock the lid in order to remove the key and activate the switch for normal operation The two identical keys provided at manufacture are unique to your projection head serial number as identified on the back of the Christie key fob and cannot be duplicated If you lose or damage a key contact your dealer or Christie for a new security lock and key set the keys cannot be replaced individually NOTES 1 The high security interlock requires a Type 3 Interface Board and main projector software v10 0 30 or higher 2 It is recommended that all keys to the projector be kept in a locked cabinet at the site Other CP panels are not removable with standard tools or they can be removed only where there are other obstacles in place that prevent theft or tampering Touch Panel Controller TPC The Touch Panel Controller TPC is a portable touch sensitive screen used to control the projector At the TPC general users can turn the lamp ON OFF select a specific source input as defined in one of 32 display setups created by the installer and obtain basic status It is typically mounted on the rear of the projector or at some other convenient nearby location and connects to
229. rowson S Crom O OOO S rorem Comm O S Tauren OO S Comoros eemo O e ome System Supervisor Module Detected Not Detected CP2000 XB User Manual 3 15 020 100163 04 Rev 1 06 2009 CHRISTIE Section 3 Operation Self Test OK Failed Ballast Communications OK Failed Can also be set to trigger a full screen flashing red alarm window on the TPC Note that if a DMD temperature exceeds a certain factory set threshold for at least 2 seconds the lamp will automatically shut down Recovery requires that the DMD temperature fall to a safe factory set threshold 3 5 3 TPC Alarm Window Identifies the new alarm __ gt Unexpected Lamp Off condition Interlock System has detected an open interlock Extractor Fan Open Blinking Red New Alarm Condition Select to shunt disable this alarm e Condition will persist until rectified but will not trigger another alarm window e Acknowledgements are discarded upon on next TPC power up alarm window will re appear Figure 3 6 Flashing Alarm Window In addition to the status bar at the bottom of any TPC screen a full screen red alarm window flashes if one of the alarm conditions shown in the left column of Table 3 2 is encountered If it is an interlock failure power will no longer reach the lamp DC output is stopped and the lamp button on the TPC Main menu will be disabled Table 3 2 Alarm Conditions and Solutions FAILED INTERLOCK Lamp door is open F
230. s and functions are illustrated and explained below NOTES 1 Shown are SAMPLE menus your specific text and or icons may vary according to settings recorded in the password protected menus By default the Main menu offers 32 pre configured channels 2 If necessary adjust TPC screen brightness and contrast via the Windows CE Display Settings for this device service password required If your TPC is enclosed in a blue casing use the small knob on the back of the unit to adjust screen settings 3 5 1 TPC Main Menu Main Status Custom Advanced Admin About Diag 1998x1080 UA 2048x858 L ON OFF ZA Flat XYZ a Scope XYZ P eal ahve 8 Display Buttons channels fil 19981080 ri 2048x056 Bouser Burons Open 1 Select pre defined source Flat F3 Scope PS and close the shutter 2 Image will change lt 3 Additional sources on 2nd Reserved miig Reserved Ha BA PCF Flat PCF Scope aS vik Test Patterns Cycle A 1920x1038 E 1920x804 through available test Flat P3 Scope P3 pene Anamorphic Lens In Out Channel Menus Lens Intelligent Lens Status Button System Select to adjust l H 1 6 CH 9 16 Lens lens mount e Go to Status Menu e Flash indicates an alarm 3 15 17 00 ry User Level Button condition Color identifies user e Color indicators described rights Select to below Figure 3 3 Main Menu Options change NOTE Using the small Status and User buttons in the bottom corners does not affect t
231. set correct Adjust as necessary using the vertical offset knob 3 Is the auxiliary lens straight Rotate to orient aperture correctly 7 6 12 The Display is Noisy CAUSE REMEDY 1 Display adjustment at your input source may be required Adjust pixel tracking phase and filter Noise is particularly common on YPbPr signals from a DVD player 2 The video input may not be terminated Make sure the video input is terminated 75Q If it is the last connection in a loop through chain the video input should be terminated at the last source input only 3 The input signal and or signal cables carrying the input signal may be of poor quality 4 Ifthe distance between the input source device and the projector is greater than 25 feet signal amplifica tion conditioning may be required 5 Ifthe source is a VCR or off air broadcast detail may be set too high 7 6 13 There are Random Streaks on the Bottom of the Image CAUSE REMEDY 1 Ifa24Hz or 25Hz HDSDI signal or a 50 Hz SDI digital PAL signal make sure to use non cinema processing delete the checkmark for Cinema checkbox in the Touch Panel Controller s Advanced menu NOTE password protected 2 Or if you do not have access to the Touch Panel Controller s Advanced menu and cannot adjust the processing path use your 3rd party input source to crop off the streaks CP2000 XB User Manual 7 7 020 100163 04 Rev 1 06 2009 CHRISTIE 8 Specifications Due to continu
232. sh NOTE The new projector address will also be implemented in the Admin General menu so that the TPC will look for this projector when you have finished setting up all network changes CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation 5 When a new address is implemented in the projector another dialogue box will remind you that if your settings moved the projector to a different network most common the TPC will no longer be able to control the projector Ignore any Cancel button that may appear in this dialogue box You must therefore immediately change the TPC Ethernet configuration if you have changed either or both of the following e Any of the first 3 octets of the IP Address 1 e the network node e The Subnet Mask Be sure to change the TPC address before re booting the projector Warning 1 For both devices pro jector and TPC the Subnet Mask and the first 3 octets of their IP addresses must match otherwise the devices are on different networks and cannot communicate 2 Do not re boot until this match is con firmed You do not have to change the TPC Ethernet configuration if you have changed only the last octet of the projector s IP Address In this case rare both devices still belong to same network and will be able to communicate with each other 6 Change the TPC Ethernet network configuration below HOW TO CHANGE YOUR TPC S IP ADDRESS Select TPC at the top of the
233. shed by the printing lab to the producer for acceptance of image and sound before screenings and manufacturing begin A check print is similar but is made from the internegative A blacktrack answer print has no soundtracks ASPECT RATIO The ratio of the width of an image to its height such as the 4 3 aspect ratio common in video output Also expressed as decimal number such as 1 77 1 85 or 2 39 The larger the decimal the wider and less square the image AUTHORING The process tools and working environment by which content elements and functions are compiled formatted coordinated and tested for presentation on target systems Comment Authoring in the context of digital cinema does not necessarily result in inseparably married or mixed content components Rather reference is made to a virtual answer print the elements of which may subsequently be subdivided or combined encrypted in whole or part and packaged in various ways for distribution of the title a version of the title or an update for revision of the title in the field A 2 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE l Appendix A Glossary AUTOMATION A system used in a theatre projection booth that responds to cues commands or relay switches and then controls various elements of presentation such as e picture format and corresponding lens flat or scope e sound format and corresponding cinema processor settings e curtain movement and posi
234. signal matching the vertical sync Hardware Instructions Connect two HD SDI signals from a 3D media server to the projector s SMPTE cinema ports A and B One carries left eye data the other right eye data Connect to either port you will configure the projector to multiply and interleave the L R signals properly Web User Interface Instructions 1 Click Enable 3D 2 SET THE FRAME RATE NOTE 6 2 can now be used for 3D content in flat 1998 x 1080 or scope 2048 x 858 displays Both incoming frame rates are likely too slow for flicker free 3D viewing and need to be increased within the projector for at least 96 Hz output For example a typical HD SDI rate of 24Hz is still only 48 Hz when L R are combined see Figure 3 12 In the Custom 3D Control menu set the desired Frame Rate N M ratio or number of frames displayed per number of frames for complete data For example a 6 2 setting creates 6 frames from 2 inputs 144 Hz The resulting frame rate cannot exceed the maximum frame rate possible in the projector with 24 Hz full screen incoming signals use a maximum factor of 5 2 NOTE Frame rate multiplication less than 6 2 may flicker at slow incoming frame rates 3 DEFINE SYNC INPUT LOCATION For dual inputs Main Status Custom Advanced Admin About s Enable Test Frame Rate f4 2 e Set the L R Input Reference option to Active Port A R L R or vice versa Step 3 e Set the Input GPI to None
235. splays using this TCGD regardless of how much light must be discarded See White Tolerance Notes below Checkbox Enter a checkmark to enable tolerance around the white point Delete the checkmark to match the white point precisely Cancel new unsaved TCGD settings Cancel tested via Test button but unsaved MCGD settings See Restore Notes below Apply current settings to the image without saving Save current MCGD settings as a new OnSite or other file name NOTE OnSite is a permanent over write of any previous OnSite file and cannot be cancelled in the future except by another over write If desired create other MCGD files to reference under specific conditions and for specific sources or channels See Create MCGD Notes below Save current settings to anew TCGD NOTE ndustry standard TCGD files are write protected and cannot be modified unless saved under a different filename For theatre use there should be little need to create custom TCGDs as the pre defined TCGDs are used instead See Create TCGD Notes below CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation MEASURED MCGD NOTES For each color record the native uncorrected x y color coordinates measured at the screen These values simply represent the currently viewable primary colors and collectively when saved will define the raw color performance reference point for this projector in the current environment Each radio b
236. sses to complete its switch Ideally when this interval is properly set and exactly suits the speed of your device neither eye sees image data intended for the other eye This helps to prevent color artifacts and ghosting while ensuring that each eye sees all intended data NOTE Because the Dark Time interval essentially increases frame rate increasing this setting beyond its range for the current frame rate factor will cause image break up 2048 x 1080 displays may be cropped Likewise a setting less than the minimum is not supported and simply sets the interval to its minimum The Output Delay setting shifts the 3D sync in relation to the Dark Time interval starting each frame slightly earlier or later Adjust only as necessary too much offset can cause bleed through where each eye sees some data that is intended for the other CP2000 XB User Manual 3 25 020 100163 04 Rev 1 06 2009 Section 3 Operation 3 26 CHRISTIE Custom Lamp Menu As shown in Figure 3 13 the Lamp menu provides controls for maintaining a specific light output over time LiteLOC or setting a precise power level for the lamp Current Channel Toggle LiteLOC function ON OFF Set and maintain consistent light output as indicated in the Set light level window Lamp power range adjustable from 75 to 110 if LiteLOC is not in use or as temporary override Display of current lamp settings automatically updated
237. ssing with DVI sources having high resolution and frequency combinations See examples in Table 3 3 Important Attempting to use cinema processing when the incoming DVI vertical frequency is too high can cause a TPC start up error Turn cinema option OFF then cycle power OFF ON Refer to Table 5 1 Compatible Non Cinema DVI Sources All Digital RGB 8 Bit on page 5 2 for a complete list Table 3 3 Processing Path for DVI Sources Examples RESOLUTION VERT FREQ TYPE OF PROCESSING yoann Table 3 4 Summary of Custom Page 1 Menu Options CUSTOM PAGE 1 MENU OPTIONS Channel Identifies sets button 1 32 for current Custom menu settings To assign a new channel for the current Custom settings select the desired display will also change and press SAVE Buttons representing channels appear in order on the Main menu Channel Name Current name or title for a button identifying a source such as a movie title or DVD Select to rename using pop up keyboard Up to 32 names can appear on the TPC Main menu Shows icon defined for current source Press to assign a different icon Cinema Keep checked for most sources default ensuring that incoming data is processed using the complete cinema path and scaled to fill the screen where possible Currently cinema sources A B projector inputs should always utilize the cinema path and scaling Clear the checkbox only for incoming DVI having a frame rate gt 60 Hz af SXGA or gt 48 Hz if 2
238. ssword required Enter the size of the lamp currently installed in the projector factory default 2 0 kW Refer to Section 3 Operation if you need help using the TPC menus Also record the lamp type on the Lamp Installed label SET THE CABLE LENGTH Still in the Admin Lamp menu use the Cable Length m text box to record the length of high voltage DC cables connected between your lamp ballast and projection head This Record which lamp Main Status Custom MNENE Uacnan About is installed NOTE L 2 0 kW 3 0 kW 4 5 kW 6 0 kW Record length of ballast DC cables Ballast Cable Length m 15 Lamp must be OFF Foot Lamberts Calibration Min FL Max FL Lamp GPIO 11 11 06 Source Screen Gamut P Config General_ Figure 2 6 Cable Length value regulates the voltage drop that occurs over distance and ensures that adequate voltage reaches the lamp Particularly in projectors rented for temporary installations the setting may have to be changed from its last use Adjustment range is 2 30m 62 100 ft in 1m increments CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 2 Installation amp Setup 2 2 2 2 1 STEP 7 Ignite the Lamp and Select the Source At the TPC Main menu press the lamp button and hold for two seconds to ignite the lamp Press the desired channel button on the Main menu The source will be displayed according to p
239. st Setting Advanced Tab e If FFFTP still fails to download files properly try the WS_FTP or similar program 3 56 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 3 Operation 3 8 Working with the Lamp Simple software controls and adjustments can help to optimize lamp performance and ensure the brightest most uniform image possible for the life of the lamp These controls are located in the Main Advanced Preferences and Advanced Lamp menus on the TPC NOTE For individual menu functions refer to Section 3 5 Using the Touch Panel Controller 3 8 1 Turning the Lamp ON OFF Main Status Custom Advanced Admin About Diag sii Lamp ON OFF A 1995x1080 5 2048x858 Select and hold for Flat wz Scope vz 1 2 second A 1998x1080 WA 2048x858 G Flat P3 Scope F3 Reserved A Reserved PCF Flat PCF Scope N 1920x1038 UA 1920804 t Flat PS Scope PS HLA 15 17 00 Figure 3 44 Lamp Button on TPC ON With all CP breakers set to ON ignite the lamp by selecting the lamp button on the Main menu of the TPC make sure to select and hold for approximately 1 2 second OFF To turn the lamp OFF select the lamp button on the Main menu of the TPC make sure to select and hold for approximately 2 second Then WAIT for fans to run for 10 minutes to cool the lamp and other compo nents then turn OFF all breakers 3 8 2 If the Lamp Won t Turn On If the lamp fails to ignite the projector will automat
240. stom Advanced admin About EE E Test Patterns pattern as 2048 x 1080 If not Current Test Pattern P CFE Greyv5o selected adjust cropping etc for test pattern Conditions for triggering an alarm in TPC window larm Triggers Over Temperature Fan Fail Lamp Expiry Lamp Life 2 000 Language English Choose language for TPC menus Stops upon opening of Advanced menu Select increment and adjust calendar time Enter the hours you expect to log on this lamp Click to save adjust Enable to displa isplay ments reset clock message when lamp expires reaches Lamp Limit Enable to display a screen saver on the z TPC after the C 15 20 58 pi desired delay Min Figure 3 16 Advanced Preferences Menu Options Table 3 9 Summary of Advanced Preference Menu Options ADVANCED PREFERENCE MENU OPTIONS Test Patterns Display an RGB 12 bit test pattern or turn patterns off Always turn OFF to resume normal operation Full Screen Enter a checkmark to display test patterns in full 2048 x 1080 resolution Clear the checkbox to work with cropping controls for screen size and shape as desired Note changes are temporary 1 e applied for the cur rent test pattern only This control is not used for sources Alarm Triggers Choose which conditions you want to trigger an Alarm Window
241. sts available in Custom Menu 3D is in use 3D Control Menu Clear 1 or more channels restore factory defaults Native color reference Choices defined by installer Default OnSite PCF list replaces Color Space Gamma LUT CLUT Target Color and Source options List is configured by installer or administrator Figure 3 8 Custom Page 1 Menu Using The availability of options in the Custom menu depends on whether you choose to use pre defined configura tion files PCFs already downloaded to projector memory Figure 3 8 or whether you prefer to implement your own Custom settings Figure 3 9 Although pre defined PCFs were originally intended as part of distributed content so that the intended image quality cannot be compromised this practice is currently rare Instead PCFs may be created using DCP Librarian and downloaded to the projector if desired Most applications such as cinema postproduction and non cinema alternative displays require that one or more display parameters be individually adjusted clear the Use PCF checkbox so that all Custom parameters are enabled Source resolution aspect ratio and offset Choices defined by installer or administrator 3 20 Always insert a check for cinema sources Use full cinema processing amp scaling Use for all cinema sources plus DVI sources 60 Hz or lower Main Status Custom Advanced Admiq Abot Channel Channel Mame f Cine
242. such a case will thus be based on 1 the display settings in the supplied PCF and 2 the remaining Custom parameters that are not contained in a PCF the physical location of the input connec tion such as a cinema port or DVI port the screen format data format and processing path SAVING OR DELETING Changes in the Custom menu are saved when you leave the menu Or to delete one or more channels use the trash bin Delete button note a caution dialog box will appear first CP2000 XB User Manual 3 19 020 100163 04 Rev 1 06 2009 Section 3 Operation Custom Page 1 Menu CHRISTIE As shown in Figure 3 8 and Figure 3 9 clearing or checking the Use PCF checkbox determines which Custom settings are available for use Icon for current setup Click to change icon ID for current custom settings Appears on Main menu Source connection location Packing mode and bits of your source USE A PCF OR NOT Always select for cinema sources Use full cinema processing amp scaling Use for all cinema sources plus DVI Main Status Fustom advanced Admin Jabout acl cha ra M Grem B 1920x804 Scope Mise PEE 30 a E Input 292 Dual Predefined DCDM RGB 185 Data Format jazz Unpack 106Bik OE Fran 7 Page 1 3D Control Lamp Lens 15 20 37 Pre defined Configurations sources with vertical freq 60Hz or lower Use pre defined PCF Refresh Update Refresh all selection li
243. t If this position is not possible such as when the projector is significantly higher than the center of the screen rely on offset to compensate To avoid keystoned images keep the projector as orthogonal to the screen as possible See Figure 2 17 1 2822 Tilted Projector Inclined screen Figure 2 17 Tilt Projector to Match Check with theatre personnel for the degree of screen tilt or measure this incline with a protractor at the screen Then TILT the projector to closely match this screen tilt angle For any installation you can tilt the front end of the projector up or down as much as 15 see Figure 2 18 Likewise side to side tilt must not exceed 15 see Figure 2 19 This limit ensures safe lamp operation and proper position of the liquid cooling reservoir in the projector Warning Tilt only as shown l j Hi AY a l i Figure 2 19 Side to Side Tilt Special Orientations Since this projector cannot be inverted or tilted beyond 15 during use all installations are front mount and require the Normal Front Image Orientation setting in the Admin General menu For shipping remove lamp and ro
244. t language font type font color position etc in the current presentation Define the desired URI Uniform Resource Identifier 1 e cinema server or distributor providing the subtitling xml file you wish to examine then select Enable to begin the test Any errors encountered in file content or transmission from the server for example a lost file a server crash loss of communication with the server etc will appear in the window and the Enable checkbox will clear TEST METADATA xml Enable the Meta File button to test a supplied xml file required for auto configuring display parameters such as colors aspect ratio watermarks etc in certain distributed content Such metadata a k a data about data is embedded in the video stream content and should be modified only by the distributor but the test may result in errors pointing to problems in metadata content or its transmission from the server Non functional Main Status Custom Advanced Admin About which d Test Selection Hour Min Sec Ticks A t t to ieit E Subtitling Hees le fo f b b Offset Find available servers sr ee a server Mame IP Browse Enable Begin test of subtitle or server amp file metadata file URI Statkus Update test xml results Similar to refresh Or see if subtitling is running Test results May show errors in xml content and or transmission from server F Em Server Diag Interro
245. t A and the cable connecting server output B is connected to pro jection input B e Set Output GPO according to which of the projector s GPIO outputs is currently wired to your emitter or polarizer 7 CONNECT GPIO OUTPUT From the projector s GPIO port connect your 3D Stereo Sync cable to your 3D controlling device such as an emitter or polarizer NOTE RealD 3D sync cable recommended 8 ADJUST DISPLAY SCREEN ETC As desired adjust the image color etc 3 10 6 3D Troubleshooting Using the 3D Test Pattern Use the 3D internal test pattern to confirm 3D mode L R orientation and GPO settings This pattern automatically activates 3D mode and increases frame rate by a factor of 6 2 NOTE The test pattern will flicker significantly due to its low frame rate and is not recommended for synchronizing projector processing with your 3D device Green field eft Magenta field right A Stereo view Image Breakup Gray J n Increasing the Dark Time beyond its maximum may cause image break up Z ern White Black No 3D Effect Figure 3 58 Internal Test Pattern for 3D Certain settings in the Custom 3D Control menu are likely reversed Ghosting Cross talk Ghosting or cross talk indicates that the eyes are detecting portions of the opposing frame due to an out of sync system Adjust Dark Time and or Output Delay so that the projector s display output is synchronized with the gating switching of your glasses
246. t affect color performance Results are defined in a file activated and downloaded to projector memory to be used as a basis for all future displays If there are changes to the environment in the future for example a new screen is installed the CP2000 XB should be re calibrated Also note that correction for proper color balance sometimes reduces overall light output NOTE Most gamut functions are also now available in the TPC Gamut menu password required Multiple MCGD files can be saved for use in different situations such as when an anamorphic lens is swapped on and off the projector Electronic Screen Masking DCP Librarian also provides a powerful masking tool for precision cropping of the image to correct for geometry problems such as a keystoned image The effect is similar to aperture plate filing typically done for correcting images from film projectors As in the calibration of color screen masking adjustments are global that is you can create a variety masks and download them to projector memory for use with sources as desired Mask settings are distinct from aspect ratio or screen position settings NOTE Most screen functions are also now available in the TPC Screen menu password required PCFs Rare Numerous settings collected into a single Projector Configuration File further control processing variables for optimized display of specific source material Each PCF file typically created in DCP Librarian pre defines
247. t lamp type from the Lamp Type drop down menu c Enter the serial number and the number of hours logged on the newly installed lamp d Select the reason why the lamp was changed from the Change Reason drop down menu e Click Save to record the number and to reset the lamp timer The timer will now begin to log time for the new lamp 6 10 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE i Section 6 Maintenance 6 4 2 STEP 14 Adjust Lamp Position Using the TPC adjust the lamp position LampLOC within the projector as described in Section Advanced Lamp Menu on page 3 30 This ensures maximum performance with the lamp bulb well centered with the reflector and distanced correctly from the rest of the illumination system Filter Replacement Procedure Replace the air filter whenever the lamp module is replaced or more frequently if operating the projector in a dusty or dirty environment Check monthly in all cases The filter is located on the operator s side of the projection head near the front See Figure 6 4 Before You Begin Power Down and Disconnect From AC Read and follow all other general lamp precautions in Section 6 1 Warnings and Guidelines STEP 1 Turn OFF Main AC a Allow the fans to run at least 10 minutes for cooling b At the breaker panel on the projector set the 3 phase MAIN AC circuit breaker to OFF Warning Never attempt to remove the lamp when it is hot The lamp is under
248. tate the projector box as needed CP2000 XB User Manual 2 13 020 100163 04 Rev 1 06 2009 Section 2 Installation amp Setup CH IS TIE l 2 3 5 Hoisting and Stacking 2 14 For some installations such as large venue rental staging applications you will likely have to safely lift or hoist this projector or a stack of 2 projectors into place Keep in mind the following critical safety guidelines for all handling of the projector Carrying Moving the Projection Head AATA Four or more people can lift and hand carry one projection head with or without a FredFrame a short distance as required Never attempt to carry a stack by hand To use equipment such as a forklift to move the projection head always install a FredFrame first Using a Forklift DAUA Do not attempt to use a forklift without first installing the fork lift rails on the bottom of the FredFrame otherwise the base of the projector may crush and damage inter nal components Strong extruded rails that mount to the bottom of the FredFrame accommodate forks from a forklife and are mandatory for this method of transport Do not lift the projection head equipment unless the FredFrame and forklift rails are installed Always follow the instructions provided with the FredFrame kit Using the FredFrame To hoist stack and or fly projectors you must properly secure each projection head within a FredFrame and use appropriate rigging and safety cab
249. ted color Turn test pattern off Save MCGD coordinates to new onSite file or other file accessed in the Custom menu Save TCGD coordinates to a new target file accessed in the Custom menu Test target color in display without saving Create MCGD MCGD Create TCGD TEGD eq Advanced Admin About Target TOGD Red C areen C Blue x 0 68 y fo Jz Magenta Gain 0 C Cyan C Yellow white White Tolerance Ee SOUFCE Screen Ge Ga a ecra General General Lamp GPIO B2344 G Figure 3 30 Admin Gamut Menu Options ADMIN GAMUT MENU OPTIONS MCGD measured at the screen See Measured MCGD Notes below Define the location enter x y coordinates of each corner of a tolerance box around the target white Table 3 17 Summary of Admin Gamut Menu Options CHRISTIE Desired x y target coordinates for each color Luminance Enable disable tolerance NOTE A tolerance discards less light Define 4 corners 0 1 2 3 of a tolerance box around white Go back to previous MCGD and TCGD coordinates NOTE Restore of MCGD requires that coordinates be tested via Test but ton but not saved point for the current TCGD A tolerance minimizes the light discarded in achieving the target white in the display and is recommended for theatre use Without tolerance the target white point will be matched precisely in di
250. tely The arc lamp operates at a very high pressure that increases with temperature Failure to allow the lamp to sufficiently cool prior to handling increases the potential for an explosion causing personal injury and or property damage After turning the lamp OFF it is crucial that you wait at least 10 minutes before turning off the rest of the projector breakers disconnecting AC and opening the lamp door This provides enough time for the internal lamp cooling fans to properly cool the lamp Cool completely before handling Again always wear protective clothing Warning 1 Never attempt to access the lamp while the lamp is on 2 Wait at least 10 min after lamp shut off before powering down disconnecting from AC and opening the lamp door 3 SHOCK HAZARD Disconnect projection head and ballast from AC before opening the lamp door For all other precautions critical for safe removal and replacement of the lamp refer to Section 6 4 Replacing the Lamp and Filter CP2000 XB User Manual 6 3 020 100163 04 Rev 1 06 2009 Section 6 Maintenance CH IS TIE l 6 2 6 2 1 6 2 2 6 2 3 6 4 Maintaining Proper Cooling The high intensity lamp and electronics rely on a variety of cooling components to reduce internal operating temperatures Regular checking and maintenance of the entire cooling system is critical to prevent overheating and sudden projector failure and helps to ensure reliable operation of all projector components over
251. the 6 pin XLR connector on the projector s Communications and Source Connection Panel Tilt turn the TPC as desired for best viewing angle and use a small knob on the back to adjust its screen brightness Navigation and description of the TPC menus including password protected options is fully explained in Section 3 5 Using the Touch Panel Controller CP2000 XB User Manual 3 5 020 100163 04 Rev 1 06 2009 Section 3 Operation CHix IS TIE l 3 2 Power Up Procedure 3 3 3 6 NOTE This is a typical manual power up procedure Cinema installations may include an automation system for controlling projector start up and lamp ignition in conjunction with other variables such as lighting audio etc rN Le Do not attempt operation if the AC supply is not within the specified voltage range 1 Make sure that ballast is properly configured for the AC at your site and that it is connected via 4 cables to the projection head Refer to Section 2 7 Connecting the Ballast 2 Connect the heat extractor fan to the projection head Refer to Section 2 4 Installing a Lens Lamp and Cooling 3 Connect the head to AC The voltmeter on the back of the projector will indicate the incoming level of AC and the main PROJ STATUS light on the rear of the projector should glow a steady green At this point only the light engine fans will be running 4 Connect the ballast to AC The ballast s 3 phase LEDs and voltmeter should light up 5 Turn t
252. ther both windows form the master pull down list of test patterns available in the Advanced Preferences menu Main Status Custom Advanced Admin About Selected Test Patterns H B Grage DC2K 13 Point Ch test F eee for user Dek 17L Point access DC2K Framing a Fal Pee Meill Test Patterns 50 Grey E Unchosen test Olek 17 Point patterns alphabetical DC2K Framing Green Select to add to fteed _ DC2K Framing Red user list Lamp History Lens Test Pattern User 15 22 11 Figure 3 21 Advanced Test Pattern Menu Options e TOGGLE A PATTERN INTO ANOTHER WINDOW Highlight a test pattern checkbox to instantly move the pattern to the other window e RE ORDER TEST PATTERNS To change the order in which a test pattern will be projected when cycled with the Test Pattern button highlight the name not its checkbox in the top window and use the arrow keys near the top of the menu to move the pattern higher or lower in the list CP2000 XB User Manual 3 33 020 100163 04 Rev 1 06 2009 Section 3 Operation 3 34 Advanced User Menu CHRISTIE Manage TPC users passwords and user rights here you will be able to manage users having the same or fewer rights than your current login level and you can change the password for the current login Type of user Factory Defaults e Service e Admin e Advanced 1 12 characters User Rights Defines which TPC menus each User Name can access
253. tically ensure that the source is properly connected and of adequate quality for detection With a poor quality or improperly connected source the projector will repeatedly attempt to display an image however briefly 2 The horizontal or vertical scan frequency of the input signal may be out of range for the projector Refer to Section amp Specifications for scan frequency ranges 3 The sync signal may be inadequate Correct the source problem CP2000 XB User Manual 7 5 020 100163 04 Rev 1 06 2009 Section 7 Troubleshooting CH IS TIE 7 6 3 The Display is Faint CAUSE REMEDY 1 Brightness and or contrast may be set too low 2 The source may be double terminated Ensure the source is terminated only once 3 The source if non video may need sync tip clamping 7 6 4 The Upper Portion of the Display is Waving Tearing or Jittering CAUSE REMEDY 1 This can sometimes occur with video or VCR sources Check your source 7 6 5 Portions of the Display are Cut Off or Wrap to the Opposite Edge CAUSE REMEDY 1 Resizing may need adjustment Adjust until entire image is visible and centered 7 6 6 The Display Appears Compressed Vertically Stretched CAUSE REMEDY 1 The frequency of the pixel sampling clock is incorrect for the current source 2 Sizing and positioning options may be adjusted poorly for the incoming source signal 3 Use an auxiliary lens for typical HDTV and anamorphic DVD sources that have been re sized a
254. time Ventilation Vents and louvers in the projector covers provide ventilation both for intake and exhaust Never block or cover these openings Do not install the projector near a radiator or heat register or within an enclosure Air Filter It is recommended that you replace the air filter located on the lamp side of the projection head whenever you replace the lamp or sooner in dusty or dirty environments A clogged filter reduces air flow and can lead to overheating and failure of the projector Check monthly Refer to Section 6 4 Replacing the Lamp and Filter for instructions It is also recommended that you visually check the laminar airflow device LAD located nearby The LAD should be nearly white or light grey in color for instructions It is also recommended that you visually check the laminar airflow device LAD located nearby The LAD should be nearly white or light grey in color Exhaust Duct and Lamp Fan Interlocks After installation check maintain operation of both vane switches one in the exhaust duct and one near the lamp fan as follows 1 Turn projector ON lamp is not needed 2 Turn your extractor fan OFF 3 Confirm in LCD status display shows that the extractor fan vane switch has failed Turn fan back ON to correct 4 Block air intake at rear corner input side of projection head 5 Confirm in LCD status display shows that the lamp fan vane switch has failed Clear air intake to correct
255. tion e lighting level in the auditorium e non sync play and fade in out e digital cinema projector AUTO SOURCE The ability of a projector to automatically recognize and synchronize to the horizontal and vertical scan frequencies of an input signal for proper display BANDWIDTH The frequency range of a video amplifier BAUD RATE The speed bits per second at which serial communications travel from their origin BIT DEPTH The total number of bits available to represent each pixel or color sample in a digital imaging system Using linear binary coding the total number of resolution steps available is equal to 2 raised to the power of the bit depth BLANKING TIME The time inside one scan line during which video is not generated The blanking time of the input signal must be equal to or greater than the retrace time of the projector BRIGHTNESS In cinema projection brightness usually describes the amount of light emitted from a surface such as a screen It is measured in footlamberts or candelas per square meter CANDELA OR CANDLE Unit of measure for measuring intensity of light in certain types of projectors CHANNEL A collection of measurements stored by the projector for a given input source including frequencies pulse width polarity syncs channel number and location user adjustable display settings etc Use channels to switch between a variety of setups quickly automatically recalling previously defined dis
256. ton Select the new User Level desired for this user Press Save To change your password l 2 J 4 Select Change PW button Enter the desired password Re enter the new password in the Confirm PW box Press Save Who is currently logged on l Enter the User Menu the User Name displayed is currently logged on CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 Section 3 Operation 3 35 Section 3 Operation CHA IS TIE l 3 5 7 TPC Admin Menu 3 36 Password protected Administrators installers and service technicians only Administrator login The six Admin submenus offer a broad range of options used primarily for defining how the projector will respond to incoming sources in the given environment or for adjusting a major system parameter affecting overall performance Four of the Admin submenus Source Screen Gamut and IP Config are available to both administrators and installers Two others General and Lamp are restricted to installers service only See Figure 3 23 Other users cannot access Admin Admin Source Menu Incoming sources can vary widely in their current resolution and original aspect ratio The projector must be able to respond to the myriad of possible Figure 3 23 Access Rights for combinations projecting full images of the desired size content and Admin Menus proportion in every case This consiste
257. um aaa oe EL power Over time however the lamp will require pR vy akt rating Is rating perhaps 5120 watts example only oe wet spo H00 y p af reached more and more current in order to produce the E ol or 14 fL until eventually the lamp wattage R F papt at reaches its 6600 overdrive maximum and the E 2 fall power to it automatically levels off At this point the LiteLOC function terminates 1 e the power level stabilizes the lamp will begin to dim normally with age and the light output gauge will begin falling Either reduce your LiteLOC setting or replace the lamp Figure 3 46 LiteLOC Expiry Using Lamp Power To change to a different power level simply enter a new Lamp Power percentage at any time This will override and temporarily disable any LiteLOC setting that may be in effect 1 Set Lamp Power to apply a specific percentage of power appropriate for the installed lamp LiteLOC will automatically be disabled 2 Brightness will change accordingly new values will appear for amps volts and watts and the blue light output bar graph will move above or below the LiteLOC line depending on the new setting As the lamp ages and becomes more inefficient your chosen power level will gradually produce less and less light output To return to the previous LiteLOC setting enable the LiteLOC checkbox NOTE When re enabling LiteLOC from a current brightness level that is more t
258. ustments of the projector for precision image alignments Corresponding lamp ballasts can be located up to 100 feet away flown or not CP2000 XB User Manual 1 3 020 100163 04 Rev 1 06 2009 Section 1 Introduction CHA IS TIE l 1 2 List of Components Ensure that you have received the following components Projection Head includes e Line cord e Touch Panel Controller with mounting hardware and 3 ft cable e Standard and high security keys for lamp and igniter service access plus assorted Allen keys e CP2000 XB User Manual Lamp Ballast three phase 7 kW for all lamps in all countries Choice of lamp kit incl protective gear Cable kit incl two lamp power cables and two communication control cables Extractor Kit 50 60 Hz Choice of high contrast or high brightness lenses does not include auxiliary lens or mount both optional Optional FredFrame includes fork lift rails for bottom Optional Rack Stand 1 2 1 Power and Lamp Requirements POWER LEVELS The universal ballast in the CP2000 XB offers adjustable lamp power to suit the size of lamp currently in use Software allows each lamp to be over driven by approximately 10 of its maximum rating LAMPS The CP2000 XB accommodates different lamps Refer to Section 8 6 Lamps for a complete list of supported lamps OTHER Optional Christie components include an auxiliary lens mount and lens DCP Librarian setup software and a 50 ft TPC cable Refer to the complet
259. utton activates the corresponding full field YCbCr test pattern of this native color so that measurements can be taken For example to measure the red coordinates click the Red radio button to change the screen display to full field red and measure coordinates at the screen Repeat for each color and record them in the nearby x y text boxes After all colors have been measured and recorded select Pattern Off to leave the special test pattern mode To cancel changes and return to the previous MCGD coordinates leave the menu without saving CREATE MCGD NOTES This button collects the current color values entered for Measured MCGD where you can save them as a new OnSite MCGD file or as a different MCGD file with a different name Note that a new OnSite overwrites any previously defined OnSite file and will be the default reference point for all future color processing the old OnSite file cannot be recovered By default the projector will refer to OnSite data to calculate the corrections needed to achieve a known target color performance standard in the future However if the site requires more than one set of native MCGD values such as when an auxiliary lens is swapped in or out you can create a new MCGD file with a different file name Each setup channel can then use any desired MCGD file as the basis for the color corrections needed for a target color MCGD files are chosen in the Custom menu NOTE Once created user created MCGD files ca
260. vironment check clean and treat the following components every 6 months or so to help ensure proper lamp and projector function LAMP FAN A clogged lamp fan impeller or motor can reduce air flow leading to possible overheating and failure of the lamp Clean treat the impeller as follows 1 Vacuum loose dirt from the lamp fan impeller 2 If necessary use a brush with hot water and suitable detergent Important Do not bend the impeller blades or loosen the balancing weights IGNITER Clean the high voltage terminal and insulator to remove accumulated dust or dirt CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHix IS TIE i Section 6 Maintenance AIR FLOW INTERLOCKS The lamp fan vane switch is located within the lamp cooling compartment The extractor vane switch is located just inside the top duct on the projector lid Check and if necessary clean the switches to remove accumulated dust or dirt that could impede movement Within the exhaust duct connected at the top of the projector adequate airflow must be maintained and routed away from the operating area surrounding the projector or any nearby projectors Inspect regularly and confirm that 1 there are no obstructions or kinks within the ducting 2 all air intake areas of the projection head and ballast are unobstructed and 3 exhaust airflow at the top vent 1s 600 CFM Make sure lamp wiring does not interfere with vane switch operation Refer to Section 6 2 Maintainin
261. wattage lamp supplied by Christie 2 Lamp replacement is to be done by a qualified service technician only 3 EXPLOSION HAZARD Wear authorized protective clothing whenever the lamp door is open Never apply a twisting or bending force to the quartz lamp body Read and follow all other general lamp precautions in Section 6 1 Warnings and Guidelines STEP 1 Turn OFF the Projector Allow the fans to run at least 10 minutes for cooling Warning Never attempt to remove the lamp when it is hot The lamp is under great pressure when hot and may explode causing personal injury and or property damage Allow to cool completely STEP 2 Set Ballast Breaker Set the ballast breaker power switch to OFF CP2000 XB User Manual 6 7 020 100163 04 Rev 1 06 2009 Section 6 Maintenance CH IS TIE l STEP 3 Disconnect from AC Disconnect projection head and ballast from AC supply Warning SHOCK HAZARD Disconnect both components from AC STEP 4 Open Lamp Door 1 Open the lamp door 2 With protective clothing and shield on unlock the lamp door and open it Refer back to Figure 2 20 Open Lamp Door and Cooling Compartment on page 2 15 If desired release the latch mechanism to remove the door entirely STEP 5 Open Cooling Compartment Turn knob to open the inner lamp cooling compartment and reveal the cathode end of the lamp Refer back to Figure 2 20 Open Lamp Door and Cooling Compartment on page 2 15 STEP 6 Remove the Old Lamp
262. which may affect performance e Keep the projector away from devices that radiate electromagnetic energy such as motors and transformers Common sources of these include slide projectors speakers power amplifiers elevators etc Choose the best screen size for the application Since more magnification reduces brightness use a screen size appropriate for the venue but not larger than required Installing a large screen in a small room is similar to watching television at a close range too large a screen can overpower a room and interfere with the overall effect A good rule of thumb is to be no closer than 1 5 times the width of the screen Projector Position and Mounting Your installation site the available screen and ambient lighting all affect where the projector should be positioned In addition both throw distance the distance between the projector and screen and vertical position the height of the projector in relation to the screen must be determined for every new installation Both depend on the screen size and lens type you are using Make sure that the room can accommodate the required location of the projector for the chosen screen size Positioning at a Port Window With the projection head secured on a suitable cart position the unit so that the front bezel is less than 2 feet from the theatre s port window wall or 3 feet if the optional auxiliary lens mount will be added Center the projector with the theatre screen
263. y the ballast switch and line cord are both set for 200 VAC use Used rented ballasts shipped from other installation sites may be set to either depending on where they were last used check the status of the line cord plug and switch before attempting to connect to AC Warning Check the plug and internal switch before connecting to AC Qualified electrical technician required 1 A visual inspection of the plug can indicate 200 or 400 VAC status Modify as necessary for your site as a delta load with safety ground the plug has no neutral 2 Remove the ballast cover to access and read the Input Power Range Switch Set switch to match incoming AC 200 400 Plug must match A incoming AC 200 or 400 VAC Delta load plus safety ground No neutral Attach to Earth Ground for RF EMI Reduction Figure 2 29 Setting Up the 7kW Ballast 3 Toggle the switch left for use with 200 VAC supplies or toggle right for 400 VAC supplies 4 Attach the ground lug to Earth Ground 5 Re install the ballast cover Connect to Projector Connect all 4 ballast cables two DC power cables and 2 communication control cables to the rear of the projector and to the lamp ballast Refer to Figure 2 3 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 2 Installation amp Setup 2 8 Initial Power Up When the ballast has been properly configured
264. y 22 lb Figure 2 24 Secure e The Christie 6 in duct with fan weighs approximately 15 lb E ractorto Dud Use third party extractors only if the minimum of 600 CFM airflow can be maintained CP2000 XB User Manual 2 17 020 100163 04 Rev 1 06 2009 Section 2 Installation amp Setup CH IS TIE SECURE SAFETY CABLES Three safety cables are provided and are all mandatory whenever the fan duct assembly is suspended These cables prevent components from falling if your rigging equipment fails Figure 2 25 shows the safety cable required between the cooling assembly and projector in any installation flown or not Attach remaining safety cables between the 1 duct and fan and 2 fan and supporting structure Flown projector Rigging hardware not shown Secure safety cable A WARNINGS A e Always use a safety cable between projector and duct fan e Minimum of 3 cables required for 6 duct and or any flown installation e Minimum of 1 cable required for floor mount with 6 duct Front mount projector with no FredFrame S oe Secure safety cable to igniter door latch Interior view oC F x ee Latch i A IS Top edge of igniter doo Safety cable a Figure 2 25 Safety Cable at Projector Flown or Front Mount 2 18 CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CH IS TIE l Section 2 Install
265. y command CP2000 XB User Manual 020 100163 04 Rev 1 06 2009 CHRISTIE Appendix B ASCII Messages Examples of ILS Commands ILS Command Result aso D USI s25 s3 ILS 4 Invokes Lens Reset ILS 10 1023 264 800 1248 Moves all four motors to the specified offset focus and zoom locations Approach goes from negative to positive ILS 10 1023 264 800 1248 111 1 Moves all four motors to the specified offset focus and zoom locations Approach is specified for all four motors B 2 5 System Status SST The SST message provides a variety of information about the current state of the projector The single broad ranging request SST for all information triggers the return of a series of replies as if multiple requests had been sent In each of these replies P1 explains the general content or topic of that reply and P2 the individual details To obtain status for one topic only specify the desired P1 parameter corresponding to that topic for example the request SST 0 will trigger general projector information only For a specific single status inquiry include both P1 and P2 in the request for example SST 4 3 asks what version of SSM main software is installed Table B 6 System Status Messages If P1 0 0 Model General Projector 1 Serial Number Configuration 2 Build Date 3 Native Resolution 4 N A 5 Lamp Power Lamp Type 6 Lamp Ballast I D v 2 4c and up 7 Interface Board Serial
266. zed Primary Lens Mount to prevent collision between the projection lens and the MALM 2 Hazardous moving parts Keep fingers and other body parts away To adjust ILS settings for a particular channel 1 Select a channel from the drop down list 2 Use the designated buttons to adjust Focus Horizontal X and Vertical Y Offset and Zoom Copy ILS settings to another channel To easily copy the settings from the current active channel to another channel use the Copy Lens Settings to Channel feature Select the channel from the drop down list and click Copy to apply the changes adjust the XY offset a 23 Minimize maximize zoom Use the buitonsito Main Status P advanced Admin About Diag Focus Use the buttons to adjust the focus Use this feature to copy Copy Lens Settings To Channel specific lens settings over to multiple 01 1998x1080 Flak swz channels Figure 3 14 Custom Lens Menu Options Table 3 8 Summary of Custom Lens Menu Options CUSTOM LENS MENU OPTIONS Focus Click the buttons to adjust the focus Offset Click the up down left right buttons to adjust the image and make it square on the screen Zoom Click the buttons to minimize or maximize zoom Copy Lens Settings Use the drop down menu to select a particular channel and click Copy for the c

Christie CP2000-XB User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents