User Manual
Contents
1. use or failure to properly use the product in the application for which said product is intended Dispose of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative jaca consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 1 8 Warranty Information UL EN Statement This equipment has been tested and found to comply with the limits for medical devices in UL EN 60601 1 and FCC CE These limits are designed to provide reasonable protection against harmful interference in a typical medical installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to other devices in the vicinity However there is n2. D 1 7 Product Specifications Warranty Information 1 One Year Warranty Opticis warrants this optical DVI extension module to be free from defects in workmanship and materials under normal use and service for a period of one 1 year from the date of purchase from Opticis or its authorized resellers If a product does not work as warranted during the applicable warranty period Opticis shall at its option and expense repair the defective product or part deliver to customer an equivalent product or part to replace the defective item or refund to customer the purchase price paid for the defective product All products that are replaced will become the property of Opticis Replacement products may be new or reconditioned Any replaced or repaired product or part has a ninety 90 day warranty or the reminder of the initial warranty period whichever is longer Opticis shall not be responsible for any software firmware information or me mory data of customer contained in stored on or integrated with any product s returned to Opticis for repair under warranty or not Warranty Limitation and Exclusion Opticis shall have no further obligation under the foregoing limited warranty if the product has been damaged due to abuse misuse neglect accident unusual physical or electrical stress unauthorized modifications tampering alterations or service other than by Opticis or its authorized agents causes other than from ordinary
3. Manual Contents p i IC i S Manual Contents Welcome Product Description www opticis com System Requirements for Setup Installation Self EDID Programming Procedure Troubleshooting Maintenance Technical Support Product Specifications Warranty Information 1 Fiber Detachable DVI Regulatory Statements module DVFX 1 00 Pictorials Figure 1 Connection Diagram of Optical DVI Extension Module User s Manual Figure 2 Connection of power adapter to the transmitter and receiver Figure 3 Connection of optical fiber Figure 4 Connection of the transmitter to DVI source and receiver to the display Figure 5 Position of EDID PRG Button and Status LED 1 0 Manual Contents 1 0 1 1 1 2 1 3 1 5 1 6 1 7 1 8 1 9 1 1 1 3 1 4 1 5 Welcome Congratulations on your purchase of the Stretch DVI DVFX 100 TR Optical DVI Digital Visual Interface Extension Module This manual contains information that will assist you in installing and operating the product Product Description The DVFX 100 TR optical DVI module transmits four 4 optical data Red Green Blue and clock and can be extended up to 500 meters 1640ft over one 1 SC multi mode fiber 50 125um at WUXGA 1920x1200 60Hz vertical refresh rate The EDID Extended Display Identification Data in a display can be read and restored by just plugging once transmitter to the display This Self EDID programming feature makes
4. d the display power ON And ensure that the Status LED in transmitter and receiver turn on 1 4 Installation Self EDID Programming Procedure The graphic source equipment generally requires display information EDID It contains resolution and timing information of the display DVFX 100 TR supports Self EDID programming It is the procedure that reads the EDID from the display and stores it in the EEPROM of the transmitter You have to do Self EDID programming if the maximum resolution of the user s display is not UXGA 1600x1200 Follow the steps below to do it correctly Note1 If you know that EDID is not required by the user s DVI source Self EDID programming is not necessary Note2 The default EDID in factory ship out is programmed in the VESA standard of UXGA 1600x1200 60Hz Step 1 Power on the display Step 2 Plug the 5V power adapter to the power jack of the transmitter of DVFX 100 Ensure the Power LED ON Step 3 Push the EDID PRGM button of the transmitter with a narrow pin Then status LED will be turned ON a F oo Ss x pA Aaa AnA Status LED dem T x 7 __ Status LED k y i n Figure 5 Position of EDID PRGM button and Status LED Step 4 Connect the transmitter to the display not to the PC Then the status LED will begin to blink rapidly It indicates reading the EDID
5. from the display and storing it in the EEPROM After 7 8 sec the status LED turn OFF and it indicates completion of all procedure Step 5 Disconnect the transmitter from the display 1 5 Self EDID Programming Procedure Troubleshooting The display shows only black screen Ensure that all plugs and jacks used by external power supplies both Opticis and others are firmly connected Ensure that the Power and status LED ON Ensure that the DVI ports are firmly plugged in to the PC and display Ensure that the transmitter and receiver modules plugged correctly to the PC and display respectively Check if the PC and display are powered on and properly booted Reset the system by de plugging and re plugging the transmitter DVI port or receiver DVI port or by de plugging and re plugging the power plugs of transmitter and receiver modules Re boot up the system while connecting the optical DVI extension module Screen is distorted or displays noises Check if the graphic resolution is properly set Go to the display properties of Windows and tap the settings Ensure that the resolution sets less than WUXGA 1920x1200 at 60Hz refresh ratio Reset the system Disconnect and reconnect the optical DVI cables or 5V power adapters Maintenance No special maintenance is required for the optical DVI module and power adapters Ensure that the DVI modules and power adapters are stored or used in a benign environme
6. nt free from liquid or dirt contamination There are no user serviceable parts Refer all service and repair issues to Opticis Technical Support and Service For commercial or general product support contact your reseller For technical service contact Opticis by email techsupp opticis com or visit its website at www opticis com 1 6 Troubleshooting Maintenance Technical Support Product Specifications DVFX 100 TR Optical DVI Extension Modules O Compliance with DVI standard Supports DVI1 0 fully implemented by fiber optic communication and DDC2B by virtual DDC O Extension limit 500meters 1640feet over 50 125um multi mode fiber at WUXGA 1920x1200 60Hz refresh rate O Graphic transmission bandwidth 2 25Gbps bandwidth which covers WUXGA or even 2K or 1080p 36bit color depth oO Fiber optic connection The transmitter and receiver modules of DVFX 100 have one 1 SC receptacles so as to be connected with one 1 SC simplex multi mode fibers having 62 5 125um_ or 50 125um core O DDC connection Virtual DDC by Self EDID programming Mechanical specifications of transmitter and receiver modules m Dimensions WDH 39 x 56 x 14 6mm O Environmental Specifications E Operating temperature 0 C to 50 C E Storage temperature 30 C to 70 C m Humidity 10 to 95 AC DC Power Adapter O Power Input AC 100 240V 50 60Hz 0 1A O Power Output 5 V 1A SMPS DC power Adapter O Cord DC Jack Core is 5 V and outer is GN
7. o guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to other devices which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving device e Increase the separation between the equipment e Connect the equipment into an outlet on a circuit different from that to which the other device s are connected e Consult the manufacturer or field service technician for help e Type of protection against electric shock Class equipment e Degree of protection against electric shock Not classified no applied parts e Classification according to the degree of protection against ingress of water as detailed in the current edition of IEC 529 IPX0 ordinary equipment e This equipment is not suitable for use in the presence of flammable anesthetics or oxygen e Mode of operation continuous operation 1 9 Regulatory Statements 2011 Opticis Co Ltd All Rights Reserved Revision 1 0 Oct 13 2011 Opticis Locations Headquarters Opticis Co Ltd 907 Byucksan Technopia 434 6 Sangdaewon Dong Chungwon Gu Sungnam City Gyeonggi Do 462 716 South Korea Tel 82 31 737 8033 8 Fax 82 31 737 8079 www opticis com For order support please contact your Distributor or Reseller For technical support check with the Op
8. supplying In case of Receiver Rx power should be supplied by AC DC adapter due to no internal power supplying from the displays 1 2 System Requirements for Setup Installation Important Please keep the installation procedure below Improper or no operation may result if the start up sequence is not correctly followed Step 1 Carefully unpack the contents of the shipping group Step 2 Plug the 5V power adapters to the power jack of the transmitter and receiver Ensure the Power LED ON Blue Zam DVFX 100 DVFX 100 lt A gt Transmitter A gt Receiver gM Figure 2 Connection of power adapter to the transmitter and receiver Step 3 Please check if the maximum resolution of the display is UXGA 1600x1200 Otherwise follow the instructions for Self EDID Programming Procedure on page 1 5 Step 4 Connect SC optical fiber between the transmitter and the receiver as shown in figure 3 Figure 3 Connection of optical fiber 1 3 Installation Step 5 Plug the transmitter to the DVI receptacle of the DVI source such as PC and the receiver to the DVI receptacle of the display l f wv a DVI Source DVFX 100 Transmitter DVFX 100 Receiver Maa DVI Display Figure 4 Connection of the transmitter to the DVI source and receiver to the display Note Be recommended NOT to use any intermediate cable or adapter between them to avoid undesirable performance degradation Step 6 Make the PC an
9. the installation of DVFX 100 TR more easy and flexile at any variable resolution display systems For your convenience UXGA EDID would have been done before shipment as a default Shipping Group o DVFX 100 TR Optical DVI Extension Module One 1 pair O AC DC power adapter Two 2 units of 5V 1A o Users Manual O Option Product Simplex SC Patch Cord Multi mode fiber Up to 500m at WUXGA Q DVFX 100 8 ry Oor We og E ty we DVFX 100 Ww Rx DVI Source DVI Display Figure 1 Connection Diagram of Optical DVI Extension Module 1 1 Welcome Product Description System Requirements for Setup O Hardware requirements m You have to have a DVI graphic controller or card having a DVI port in your PC SUN or Mac systems It should support the maximum graphic resolution feature of displays to be connected m No special requirements for memory size CPU speed and chipsets if you ve already properly installed your DVI graphic controllers or cards O Software requirements E No special restrictions if you ve already properly installed your DVI graphic controller in your OS O AC DC Power Adapter Technical Advisory The transmitter Tx module of DVFX 100 TR is designed for power protection circuit from conflict of power supply between the external AC DC power adapter and your DVI source by 14 pin We strongly recommend to use external AC DC adapter for Transmitter Tx for stable power
10. ticis web site www opticis com or contact techsupp opticis com
Download Pdf Manuals
Related Search