6 - Einhell
Contents
1. special tools are available from the professional Service Centre AFTER SALES SUPPORT A 01516491500 1890946244 amp www einhell co uk MODEL GLPC 41 Instructions 0 65mm A 025 Chain sharpening Fig 27 Sharpen the chain using protective gloves and a round file of 53 16 4 8mm Always sharpen the cutters only with outward strokes Fig 27 observing the values given in Fig 26 After sharpening the cutting links must all have the same width and length A sharp chain produces well defined chips When your chain starts to produce sawdust it is time to sharpen ii A X After the blades have been sharpened 3 4 times check the height of the depth limiter and if necessary lower it with a flat file and then round off the front corner Fig 28 AFTER SALES SUPPORT A 01516491500 1890946244 amp www einhell co uk MODEL GLPC 41 Instructions 6 Chain tension Check the chain tension frequently and adjust as often as necessary to keep the chain snug on the bar but loose enough to be pulled around by hand See also Page 16 Breaking in a new saw chain A new chain and bar will need chain readjustment after as few as 5 cuts This is normal during the break in period and the interval between future adjustments will begin to lengthen quickly Never have more than 3 links removed from a loop of chain This could cause damage to the sprocket Chain lubrication Always make sure the automatic2. be moved smoothly but is still closely seated Fig 9 Item A Increase the tension by turning the chain tensioning wheel IN A CLOCKWISE DIRECTION When the saw chain is correctly tensioned hold the tip of the bar upwards and completely tighten the bar fastening wheel Fig 8 Item B To test chain brake NOTE A new saw chain stretches requiring adjustment after as few as 5 cuts This is normal with a new chain and the interval between future adjustments will lengthen quickly CAUTION The brake lever should snap into both positions If strong resistance is felt or the lever does not move into either position do not use your saw NOTE Take it immediately to a professional Service Centre for repair If the saw chain is TOO LOOSE or TOO TAUT the drive wheel chain bar chain and crank shaft bearing will suffer premature wear Fig 9 Item A shows the correct tension when cold and Fig 9 Item B shows the tension when warm Fig 9 Item C shows a chain that is too loose Getting Started 4 Getting Started Fuel and lubrication 1 Fuel Recommended fuels 2 Mixing fuel Lubrication of chain and chain bar NOTE Never use straight petrol in your unit This will cause permanent engine damage and void the manufacturer s warranty for that product Never use Engine pre start checks a fuel mixture that has been stored for over 90 days NOTE If 2 stroke lubricant is to be used it must bea premium grade oil f
3. order Service and clean the appliance regularly Adapt your working style to suit the appliance Do not overload the appliance Have the appliance serviced whenever necessary Switch the appliance off when it is not in use Wear protective gloves Service information We have competent service partners within the UK whose contact details can be found on the www einhell co uk website These partners can help you with all service requests such as repairs spare and wearing part orders or the purchase of consumables Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables Category Example Cutter bar spark plug air filter petrol filter ES io Not necessarily included in the scope of delivery AFTER SALES SUPPORT A 01516491500 1890 946244 LJ www einhell co uk MODEL GLPC 41 Useful Information In the event of a defect or fault please register the problem on the internet at www einhell co uk or telephone one of the Helpline numbers at the bottom of the page Please ensure that you provide a precise description of the problem and answer the following questions in all cases e Did the equipment work at all or was it defective from the beginning e Did you notice anything symptom or defect prior to the failure e What malfunction does the equipment have in your opinion main symptom Describ
4. plug wrench DO NOT USE ANY OTHER TOOLS Do not pull hose completely out of tank 5 Clean the spark plug with a copper wire brush or fit a new one 4 Lift the filter A out of tank Fig 22 Carburettor setting 5 Pull off the filter with a twist and clean it if the filter is damaged dispose of it The carburettor has been set to its perfect adjustment at the factory If it requires 6 Insert a new filter Place one end of the filter into the tank opening Make sure adjusting take the saw to your nearest authorized after sales service outlet that the filter is seated in the lower corner of the tank If necessary use a long screwdriver to move the filter to its correct position taking care not to damage it in the process Fill tank with fresh fuel oil mixture See Section Fuel and Lubrication Install fuel cap Setting the idling speed Set the idling speed when the machine is warm If the engine stalls when the throttle is not pressed and you have ruled out all the other causes listed in section 9 Troubleshooting the idling speed must be adjusted To do this turn the idling speed screw Fig 22 Item B clockwise until the machine runs smoothly at idling speed If the idling speed is so fast that the chain turns as well it has to be reduced by turning the idling speed screw counter clockwise Fig 22 Item B for as long as is required for the chain to stop turning as well AFTER SALES SUPPORT ln 01516491500 1890946244 amp www e
5. technical support or in the unlikely event that your purchase is faulty please telephone our Helpline for immediate assistance Faulty product claims made within the 3 year warranty period will be repaired or replaced free of charge provided that you have satisfactory proof of purchase keep your till receipt safe This does not affect your statutory rights However be aware that the warranty will become null and void if the product is found to have been deliberately damaged misused or disassembled The reprinting or reproduction by any other means in whole or in part of documentation and papers accompanying products is permitted only with the express consent of Einhell UK Ltd Subject to technical changes AFTER SALES SUPPORT A 0151 6491500 1890 946244 LJ www einhell co uk MODEL GLPC 41 AFTER SALES SUPPORT A 0151 6491500 1890 946244 LJ www einhell co uk MODEL GLPC 41 General Information and Safety Instructions 2 Read the user manual before using the machine On all jobs performed with the saw you must always wear safety goggles to guard your eyes from flying materials objects and a sound proof helmet ear plugs or the like to protect your hearing Wear a safety helmet if there is a risk of objects falling on you from above Wear gloves to protect your hands Wear safety shoes to protect your feet Warning Danger Make sure that the chain brake is released Pull back the handle chain brake before o
6. the spark plug Store the unit in a dry place and away from possible sources of ignition such as a furnace gas hot water heater gas dryer etc Putting the saw back into operation Remove the spark plug See also Page 28 Pull the starter rope briskly to clear excess oil from the combustion chamber Clean the spark plug and check that the electrode gap is correct Prepare the unit for operation Fill the fuel tank with the proper fuel oil mixture See the Fuel and Lubrication Section UAWN 39 AFTER SALES SUPPORT A 0151 6491500 1890 946244 LJ www einhell co uk MODEL GLPC 41 Useful Information Environmental protection Dispose of soiled maintenance material and operating materials at the appropriate collection point Recycle packaging material metal and plastics Ordering replacement parts Please quote the following data when ordering replacement parts Type of machine GLPC 41 Article number of the machine 45 018 26 Identification number of the machine 11014 Replacement part number or description of the part required For our latest prices and information please go to www einhell co uk AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 Useful Information Troubleshooting Incorrect starting procedures PoE ah neon gP in the User Manual Incorrect carburettor mixture Have carburettor adjusted by Unit won t start adjustment
7. 7 5cm cutting length e Semi automatic choke assisting start up e 21m s chain speed e 260ml fuel tank capacity e Mixer bottle included AFTER SALES SUPPORT 74 01516491500 1890946244 amp www einhell co uk MODEL GLPC 41 AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 Instructions 6 Instructions Restarting a warm engine Always pull the starter cable slowly until you feel the initial resistance e Make sure the switch is in the ON position before you then pull it quickly to start the engine Do not allow the starter e Pull the starter rope rapidly 6 times The engine should start cable to whip back of its own accord To stop engine e Release trigger and allow engine to return to idle speed e Move STOP switch down to stop engine To stop the engine in an emergency activate the chain brake and switch the ON OFF switch to Stop 0 General cutting instructions Felling trees is prohibited without the necessary training Fig 12E AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 AFTER SALES SUPPORT 74 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 Instructions 6 Instructions Felling e Felling is the term for cutting down a tree Small trees up to 6 7 inches 15 18cm in diameter are usually cut in a single cut Larger trees require notch cuts Notch cuts determine the direction the tree will fall e A retreat
8. GARDENLINE 41cc Petrol Chainsaw Operating Instructions User Guide TOU IVN R z ui m4 L 4 Dou aN INA N ES RE a lt A n After Sales Support E HEN c KS Low KICKBACK d hd Now you have purchased a Gardenline product you can rest assured in the knowledge that as well as your 3 year parts and labour guarantee you have the added peace of mind of dedicated helplines and web support gt amp p amp 4 amp A W c ETS J AFTER SALES SUPPORT rer 0151 649 1500 Fe G 1890946244 www einhell co uk MODEL GLPC 41 Contents Welcome 1 Page Congratulations 3 Welcome You have made an excellent choice with the purchase of this quality 4 11 General Information and Safety Instructions a kalakan 12 17 Assem bly and Parts List By doing so you now have the assurance and peace of mind which comes from purchasing a product that has been manufactured to the highest standards of 18 20 Getting started performance and safety supported by the high quality standards of ALDI 21 Features We want you to be completely satisfied with your purchase so this Gardenline 22 38 Instructions product is backed by a comprehensive manufacturer s 3 year warranty and an outstanding after sales service through our dedicated Helpline 39 44 Useful information 45 FAQ We hope you will enjoy using your purchase for many years to come A7 Warranty Card If you require
9. H StangenstraBe 1 70771 Leinfelden Echterdingen Notified Body No 0905 _ 2006 28 EC od No x 2004 108 EC C 2004 22 EC C 1999 5 EC C 97 23 EC C 90 396 EC_2009 142 EC C 89 686 EC_96 58 EC C 2011 65 EC x Annex V J Annex VI x 2004 26 EC 14SHW1735 01 x 2000 1 4 EC_2005 88 EC Noise measured Ly 109 6 dB A guaranteed Lwa 114 dB A P 1 5 kW L O cm Notified Body Emission No e11 97 68SA 201 0 26 2698 00 Standard references EN ISO 11681 1 EN ISO 14982 Landau Isar den 17 09 2014 Weichselgartner Gefiera First CE 14 Art No 45 018 26 l No 11014 Subject to change without notice AFTER SALES SUPPORT Je 01516491500 1890946244 LL wwweinhell co uk au Ya Luo Yong Product Management L Archive File Record NAPRO1 1211 Documents registrar Markus Jehl Wiesenweg 22 D 94405 Landau Isar MODEL GLPC 41 FAQ How do claim for a warranty matter How do obtain spare parts not covered by the warranty AFTER SALES SUPPORT ZA 01516491500 G 1890 946244 1 Fill in the Warranty card and send to the Einhell UK Ltd Address 2 Contact Einhell UK Ltd using one of the Telephone numbers for AFTER SALES SUPPORT 3 Or contact via the Einhell UK Ltd website Make sure you have the information from the product data label or page 40 of this manual and then 1 Contact Einhell UK Ltd using one of the Telephone numbers for AFTER SALES SUPPO
10. INAL BAR The oiling hole Fig 5 Item A must be kept clear of dirt and any build up of residue Make sure the Chain brake lever is pulled back into the DISENGAGED position Fig 6A Extend the lever on the Bar fastening knob B amp completely unscrew COUNTERCLOCKWISE Fig 6B 6C Then remove the cover Fig 6D Turn the chain tensioning wheel D IN A COUNTER CLOCKWISE DIRECTION until the TANG E projecting pin is at the end of its sliding path in the direction of the clutch and gear wheel Fig 6B 6C Fit the open end of the chain bar over the bar pins F Align the bar such that the TANG E fits into the hole G in the chain bar Fig 6C 6D 15 AFTER SALES SUPPORT A 01516491500 1890946244 LI www einhell co uk MODEL GLPC 41 3 Assembly and Parts List 3 Assembly and Parts List To install the saw chain e Spread the chain out in a loop with the cutting edges A pointing CLOCKWISE around the loop Fig 7A e Slip the chain around the sprocket B behind the clutch C Make sure the links fit between the sprocket teeth Fig 7B e Guide the drive links into the groove D and around the end of the bar Fig 7B il N i fil if The saw chain may droop slightly on the lower part of bar This is normal e Pull the chain bar forward until the chain is closely seated Make sure that all the drive links are in the groove of the bar e Fit the Chain brake lever fr
11. RT and choose the option for Spare Parts 2 Or contact via the Einhell UK Ltd website where spares information amp prices are available Ja www einhell co uk MODEL GLPC 41 Warranty Card AFTER SALES SUPPORT A 01516491500 1890946244 J www einhell co uk GARDENLINE 41cc Petrol Chainsaw KEEP THIS FORM SAFE Only complete and return this form to the address below in the unlikely event of a warranty claim if you are requested by the manufacturer to return the item for replacement Then please complete this form and send it together with your receipt proof of purchase to the address below Your details Name Address Date of purchase We recommend you keep the receipt with this warranty card Location of purchase Description of malfunction Return your completed warranty card to AFTER SALES SUPPORT Einhell UK Ltd Unit 9 Stadium Court Wirral International Business Park ETA 0151 649 1500 Plantation Road 43 1890 946244 www einhell co uk Bromborough CH62 3QG MODEL GLPC 41 www einhell co uk warranty Please add the Ser Nr here Art Nr 45 018 26 Monday to Thursday 8 45am 5pm Friday 8 45am 3pm Calls cost 10p per minute from a landline calls from mobiles may vary YEAR WARRANTY You will find the 7 b character Ser Nr here 47 MODEL GLPC 41 AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41
12. d the operator PINCHING the saw chain along the BOTTOM of the guide bar may PULL the saw forward away from the operator PINCHING the saw chain along the TOP of the guide bar may PUSH the guide bar rapidly back toward the operator Any of these reactions may cause you to lose control of the saw which could result in serious personal injury Beware of the following Rotary recoil Fig 3A A Recoil distance B Recoil reaction zone Impact Jamming recoil and pulling reactions Fig 3B A Pull B Solid objects C Push To prevent pulling reactions place the wood you wish to cut against the claw stop Use the claw stop as a pivot point during cutting 6 AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 General Information and Safety Instructions When using Petrol tools basic safety precautions including the following should always be followed to reduce the risk of serious personal injury and or damage to the unit Read all these instructions before operating this product and save these instructions Safety precautions DO NOT operate a chainsaw with one hand Serious injury to the operator helpers bystanders or any combination of these persons may result from one handed operation A chainsaw is intended for two handed use Do NOT use the saw if you are tired ill or under the influence of alcohol and or drugs Use safety footwear snug fitting clothing protective gl
13. e this malfunction AFTER SALES SUPPORT MODEL GLPC 41 rs 01516491500 1890946244 LL wwweinhell co uk Useful Information ISC GmbH EschenstraBe 6 D 94405 Landau Isar Declaration of Conformity erkl rt folgende Konformit t gem EU Richtlinie und Normen f r Artikel explains the following conformity according to EU directives and norms for the following product d clare la conformit suivante selon la directive CE et les normes concernant l article dichiara la seguente conformit secondo la direttiva UE e le norme per l articolo amp verklaart de volgende overeenstemming conform EU richtlijn en normen voor het product c declara la siguiente conformidad a tenor de la directiva y normas de la UE para el art culo c declara a seguinte conformidade de acordo com a directiva CE e normas para o artigo attesterer folgende overensstemmelse i medfor af EU direktiv samt standarder for artikel f rklarar f ljande verensst mmelse enl EU direktiv och standarder f r artikeln vakuuttaa ett tuote t ytt EU direktiivin ja standardien vaatimukset t endab toote vastavust EL direktiivile ja standarditele vyd v n sleduj c prohl en o shod podle sm rnice EU a norem pro v robek potrjuje slede o skladnost s smernico EU in standardi za izdelek vyd va nasleduj ce prehl senie o zhode pod a smernice EU a noriem pre v robok a cikkekhez az EU ir nyvonal s Norm k szerint a
14. filter must be cleaned or replaced after every 20 hours of service All maintenance work on the chainsaw apart from the work described in this manual may only be carried out by authorized after sales service personnel Chain brake operational test Test the chain brake periodically to ensure proper function Perform a chain brake test prior to initial cutting following extensive cutting and definitely following any Chain brake service Test chain brake as follows Fig 20 Place saw on a clear firm flat surface Start the engine Grasp the rear handle A with your right hand With your left hand hold the front handle B not chain brake lever C firmly Squeeze the throttle trigger to 1 3 throttle then immediately activate the chain brake lever C UAWN Activate the chain brake slowly and deliberately Keep the chain from touching anything don t let the saw tip forward Cleaning the air filter Fig 21A 21B 6 Chain should stop abruptly When it does immediately release the throttle trigger 1 Remove the top cover A by undoing the cover fastening screw B on the cover You can then remove the cover Fig 21A 2 Lift out the air filter C Fig 21B 3 Clean air filter Wash filter in clean warm soapy water Rinse in clear cool water If chain does not stop turn engine off and take your unit to the nearest Air dry completely Authorized Service Centre for service 7 If the chain brake functions pr
15. htning fast reverse reaction kicking the guide bar up and back towards the operator Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator Either of these reactions may cause you to lose control of the saw which could result in serious personal injury Do not rely exclusively upon the safety devices built into your saw As a chainsaw user you should take several steps to keep your cutting jobs free from accident or injury With a basic understanding of kickback you can reduce or eliminate the element of surprise Sudden surprise contributes to accidents Keep a good firm grip on the saw with both hands the right hand on the rear handle and the left hand on the front handle when the engine is running Use a firm grip with thumbs and fingers encircling the chainsaw handles A firm grip will help you reduce kickback and maintain control of the saw Don t let go Make sure that the area in which you are cutting is free from obstructions Do not let the nose of the guide bar contact a log branch or any other obstruction which could be hit while you are operating the saw Cut at high engine speeds Do not overreach or cut above shoulder height Follow the manufacturer s sharpening and maintenance instructions for the saw chain Only use replacement bars and chains specified by the manufacturer or the equivalent e If the equipment becomes jammed when cutting s
16. inhell co uk MODEL GLPC 41 AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 Instructions 6 Chain bar maintenance NOTE The sprocket tip on your new saw has been pre lubricated at the factory Failure to lubricate the guide bar sprocket tip as explained below will result in poor performance and seizure voiding the manufacturer s warranty Tools for lubrication To lubricate the sprocket tip NOTE The saw chain does not have to be removed in order to lubricate the teeth of the chain bar Lubrication is possible during work with the engine switched off CAUTION Wear heavy duty work gloves when handling the bar and chain Set the On Off switch to Stop 0 Clean the guide bar sprocket tip Using the Lube Gun optional insert the needle nose into the lubrication hole and inject grease until it appears at the outside edge of the sprocket tip Fig 23 Rotate the saw chain by hand Repeat the lubrication procedure until the entire sprocket tip has been greased 34 Instructions CAUTION Always wear protective gloves during maintenance operations Do not carry out maintenance when the engine is hot Turning the chain bar 35 et a ESP CR PP Instructions 6 Never fit a new chain to a worn chain bar Oil passages Oil passages on the bar should be cleaned to ensure proper lubrication of the bar and chain during operation The condition of the oil pas
17. is securely supported 28 Ja www einhell co uk MODEL GLPC 41 AFTER SALES SUPPORT A 01516491500 G 1890 946244 6 Instructions Bucking using a sawhorse Fig 19 For personal safety and ease of cutting the correct position for vertical bucking is essential Fig 19 Hold the saw firmly with both hands and keep the saw to the right of your body while cutting Keep the left arm as straight as possible Keep weight on both feet When working with the saw always make sure that the saw chain and chain bar are sufficiently lubricated Cleaning maintenance storage and ordering of spare parts Disconnect the spark plug boot before doing any cleaning and maintenance work Cleaning Keep all safety devices air vents and the motor housing free of dirt and dust as far as possible Wipe the equipment with a clean cloth or blow it with compressed air at low pressure We recommend that you clean the device immediately each time you have finished using it Clean the equipment regularly with a moist cloth and some soft soap Do not use cleaning agents or solvents these could attack the plastic parts of the equipment Ensure that no water can seep into the device JE www einhell co uk MODEL GLPC 41 Instructions 6 Instructions Air filter Maintenance Never operate the saw without the air filter Dust and dirt will be drawn into the engine and damage it Keep the air filter clean The air
18. k vetkez konformit st jelenti ki CE deklaruje zgodno wymienionego poni ej artyku u z nast puj cymi normami na podstawie dyrektywy WE Aeknapnpa CbOTBETHOTO CHOTBETCTBHE C r IacHo A npek TMB Ha EC n Hopmy 3a aprHHyn paskaidro Sadu atbilstibu ES direktivai un standartiem apib dina Sj atitikima EU reikalavimams ir prek s normoms declar urm toarea conformitate conform directivei UE si normelor pentru articolul SNAWVEL tv AKOAOVEN cupp pdooorn cUpdouova pg rnv Odnyia EK kat ra rrp rurta yia To ripoi v potvrduje sljedecu uskladenost prema smjernicama EU i normama za artikl potvrduje sljede u uskladenost prema smjernicama EU i normama za artikl potvrduje sledecu uskladenost prema smernicama EZ i normama za artikal cAnenytouiuMM YAOCTOBEPAETCA TO C Ienyrouude npoAyHTb COOTBeTCTByIOT AUPEKTUBAM N HOpmam EC Nporonowye npo 3a3HaueHy HHHUE BinnoBinHicTb BHpo6y AUpeKTUBaM Ta craunapraM EC Ha BUpi6 ja u3jaByBa cnenHara coo6p3Hocr corniacHo EY nupeurHBara M HOPMHTE 3a apTHH JIM r n ile ilgili AB direktifleri ve normlar gere ince a a da a klanan uygunlu u belirtir erkl rer f lgende samsvar i henhold til EU direktivet og standarder for artikkel L sir uppfyllingu EU regina og annarra sta la v ru Petrol Chain Saw GLPC 41 Gardenline _ 87 404 EC 2009 105 EC C 2005 32 EC 2009 125 EC _ 2006 95 EC x 2006 42 EC x Annex IV Notified Body Intertek Deutschland Gmb
19. n get hot eee Clean the groove in the cutter bar AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 AFTER SALES SUPPORT Useful Information Technical data Engine displacement Maximum engine capacity Cutting length Cutter rail length Chain pitch Chain thickness Idling speed Maximum speed with cutting equipment Tank capacity Oil tank capacity Anti vibration function Chain wheel teeth Chain brake Clutch Automatic chain lubrication Low kickback chain Net weight without chain and chain bar Net weight dry Fuel consumption specific Sound and vibration L sound pressure level K uncertainty Ly4sound power level Ky uncertainty Vibration a front handle k uncertainty a Vibration ahv rear handle Khv uncertainty Chain type Bar type Spark plug vey 0151 649 1500 1890 946244 41 cm 1 5 kW 37 5 cm 16 40 cm 3 8 9 525 mm 0 05 1 27 mm 3300 300 rpm 11000 rpm 260 ml 210 ml Yes 6 teeth x 9 525 mm Yes Yes Yes Yes 4 5 kg 5 4 kg 702 g kWh 99 dB A 3 dB A 114 dB A 1 5 dB A max 6 5 m s 1 5 m s max 6 0 m s 1 5 m s OREGON 91P057X OREGON 160SDEA041 L8RTF js www einhell co uk MODEL GLPC 41 Useful Information Wear ear defenders The impact of noise can cause damage to your hearing Keep the noise emissions and vibrations to a minimum Only use appliances which are in perfect working
20. oiler system is working properly Keep the oil tank filled with Chain Bar and Sprocket Oil Adequate lubrication of the bar and chain during cutting operations is essential to minimize friction with the guide bar Never starve the bar and chain of lubricating oil Running the saw dry or with too little oil will decrease cutting efficiency shorten saw chain life cause rapid dulling of chain and lead to excessive wear of bar from overheating Too little oil is evidenced by smoke or bar discolouration AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 Instructions Storage Never put a chainsaw into storage for longer than 30 days without carrying out the following steps Storing a chainsaw Storing a chainsaw for longer than 30 days requires storage maintenance Unless the storage instructions are followed fuel remaining in the carburettor will evaporate leaving gum like deposits This could lead to difficult starting and result in costly repairs 1 Remove the fuel tank cap slowly to release any pressure in the tank Carefully drain the fuel tank 2 Start the engine and let it run until the unit stops to remove fuel from the carburettor 3 Allow the engine to cool approx 5 minutes 4 Remove the spark plug See also Page 30 5 Pour 1 teaspoon of clean 2 stroke oil into the combustion chamber Pull the starter rope slowly several times to coat the internal components Replace
21. ont hand guard Fig 8 and turn the bar fastening knob amp lever B clockwise to secure it The chain is not allowed to slip off the guide bar when you do this Only loosely tighten the bar fastening knob amp level at this stage and then follow the instructions for adjusting the chain tension as described in the section ADJUSTING THE CHAIN TENSION AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 Assembly and Parts List 3 Getting Started Adjusting the chain tension Chain brake mechanical test Wear high strength gloves at all times when handling or adjusting E Saw hain The purpose of the chain brake is to reduce the possibility of injury due to kickback however it cannot provide the intended measure of protection if the saw is operated carelessly Always test the chain brake before using your saw and periodically while on the job See P30 for details of how to perform a test of the mechanical brake NOTE If the chain is hard to turn around the chain bar or jammed it is too tightly tensioned Make the following small adjustments A Undo the bar fastening wheel B by 1 2 of a turn COUNTERCLOCKWISE Then slacken the chain tension by slowly turning the chain tensioning wheel D IN A COUNTER CLOCKWISE DIRECTION and then pull the chain back and forth on the bar Fig 8 9 Continue until the chain can
22. operly turn the engine off and return the chain It is advisable to have a supply of spare filters brake to the DISENGAGED position 4 Insert the air filter Fit the cover for the engine air filter Make sure that the cover fits perfectly when you do so Tighten the fastening screw for the cover AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 Instructions 6 Instructions Fuel filter Spark plug Fig 21B To ensure that the saw s engine retains its power the spark plug must be Never use the saw without a fuel filter After 100 hours in operation the fuel clean and have the correct electrode gap 0 6 mm The spark plug must be cleaned or replaced after every 20 hours of service filter should be cleaned or in case of damage replaced Be sure to empty the fuel tank before changing the filter 1 Remove the fuel tank cap 1 Set the On Off switch to Stop 0 2 Bend a piece of soft wire 2 Remove the top cover A by undoing the cover fastening screw B on the cover 3 Reachinto the fuel tank opening and hook the fuel line Carefully pull the You can then remove the cover Fig 21A fuel line toward the opening until you can reach it with your fingers 3 Disconnect the ignition cable D from the spark plug by pulling and twisting it simultaneously Fig 21B 4 Remove the spark plug using a spark
23. or 2 stroke air cooled engines mixed at a 40 1 ratio Do not use any 2 stroke oil product with a recommended mixing ratio of 100 1 If insufficient lubrication is the cause of engine damage it voids the manufacturer s engine warranty for that occurrence CAUTION tat Never start or operate the saw unless the bar and chain are properly installed Petrol and Oil Mix 40 1 Oil Only 1 Fill the fuel tank A with correct fuel mixture Fig 11 2 Fill the oil tank B with chain oil Fig 11 3 Be certain the chain brake is disengaged C before starting the unit Fig 11 Once you have filled the chain and oil tank tighten the tank cover securely by hand Do not use any tools to do so Features 5 Instructions Operation Starting the engine e Switch the Ignition to 0 OFF Fig 12A e Pull the choke B fully out until it locks Fig 12B e Push the primer bubble C 10 times Fig 12C e Place the saw on a firm flat surface Hold the saw firmly as shown Pull the starter cord rapidly 2 times Beware of moving chain Fig 12D e Push in the choke lever B as far as it will go Fig 12B e Set the On Off switch A to ON 1 to start the machine Fig 12A e Hold the saw firmly and pull the starter rapidly 4 times Engine should start Fig 12D e Let the engine run for 10 seconds to warm up Press the throttle lever D briefly the engine will go to idling speed Fig 12E Features e 3
24. oves and eye hearing and head protection devices Use caution when handling fuel Move the chainsaw at least 10 feet 3m from the fuelling point before starting the engine DO NOT allow other persons to be near when starting or cutting with the chainsaw Keep bystanders and animals out of the work area DO NOT start cutting until you have a clear work area secure footing and a planned retreat path from a falling branch or falling tree Keep all parts of your body away from the saw chain when the engine is running Before you start the engine make sure that the saw chain is not contacting anything Carry the chainsaw with the engine stopped the guide bar and saw chain to the rear and the muffler away from your body NEVER use a chainsaw which is damaged incorrectly adjusted or incompletely and loosely assembled Make sure that the chainsaw stops when the chain brake is applied Shut off the engine before setting the chainsaw down Use extreme caution when cutting small size brush and saplings because slender material may catch the saw chain and be whipped towards you or pull you off balance 7 AFTER SALES SUPPORT ZR 01516491500 1890 946244 LI www einhell co uk 2 MODEL GLPC 41 AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk General Information and Safety Instructions 2 When cutting a limb that is under tension be alert for springback so that you will not be struck when
25. path A should be planned and cleared as necessary before cuts are started The retreat path should extend back and diagonally to the rear of the expected line of fall as illustrated in Fig 13 e If felling a tree on sloping ground the chainsaw operator should keep on the uphill side of the terrain as the tree is likely to roll or slide downhill after it is felled e Direction of fall B is controlled by the notching cut Before any cuts are made consider the location of larger branches and natural lean of the tree to determine the way the tree will fall Fig 13 Felling cut e Use wooden or plastic wedges A to prevent binding the bar or chain B in the e Do not cut down a tree during high or changing winds or if there is a danger to cut Wedges also control felling Fig 15 property Consult a tree professional Do not cut down a tree if there is a danger of striking utility wires notify the utility company before making any cuts e When the diameter of wood being cut is greater than the bar length make 2 cuts as shown Fig 16 General guidelines for felling trees Fig 14 e As the felling cut gets close to the hinge the tree should begin to fall When the tree begins to fall remove the saw from the cut stop engine put the chainsaw Normally felling consists of 2 main cutting operations notching C and making down and leave area along the retreat path Fig 13 the felling cut D e Start making the uppe
26. perating Noise emission complies with Directive 2000 14 EC 2 General Information and Safety Instructions Explanation of the pictograms for handling on the machine Fig 2 NOTE A safety sign is fitted to the chainsaw s fan filter cover This label along with the safety instructions on these pages should be carefully read before attempting to operate this unit IMPORTANT 1 RED Warns about a dangerous method of working that must not be used 2 GREEN Recommended operation for safe sawing Recommended operation for safe sawing IMPORTANT 1 Beware of recoil 2 Do not hold the saw in one hand 3 Avoid contact with the tip of the rail chain return point RECOMMENDED 4 Hold the saw firmly with both hands Place your right hand on the rear handle and your left hand on the front handle General Information and Safety Instructions 2 Kickback safety precautions Kickback can lead to dangerous loss of control of the chainsaw and result in serious or fatal injury to the saw operator or to anyone standing close by Always be alert Rotational kickback and pinch kickback are major chainsaw operational dangers and the leading cause of most accidents KICKBACK may occur when the NOSE or TIP of the guide bar touches an object or when wood closes in and pinches the saw chain in the cut Tip contact in some cases may cause a lightning fast reverse reaction kicking the guide bar up and back towar
27. r notch cut C on the side of the tree facing the felling direction E Be sure you don t make the lower cut too deep into the trunk The notch C should be deep enough to create a hinge F of sufficient width and strength The notch should be wide enough to direct the fall of the tree for as long as possible e Never walk in front of a tree that has been notched Make the felling cut D from the other side of the tree and 1 5 2 0 inches 3 5 cm above the edge of the notch C Never saw completely through the trunk Always leave a hinge F The hinge guides the tree If the trunk is completely cut through control over the felling direction is lost Insert a wedge or felling lever in the cut well before the tree becomes unstable and starts to move This will prevent the guidebar from binding in the felling cut if you have misjudged the falling direction Make sure no bystanders have entered the range of the falling tree before you push it over Limbing e Limbing a tree is the process of removing the branches from a fallen tree Do not remove supporting limbs A until after the log is bucked cut into lengths Fig 17 Branches under tension should be cut from the bottom up to avoid binding the chainsaw e Before making the final cut always recheck the area for bystanders animals or obstacles e Never cut tree limbs while standing on the tree trunk 27 AFTER SALES SUPPORT 74 01516491500 1890946244 amp www einhell co
28. r transportation braces if available Check to see if all items are supplied Inspect the equipment and accessories for transport damage If possible please keep the packaging until the end of the guarantee period The eguipment and packaging material are not toys Do not let children play with plastic bags foils or small parts There isa danger of swallowing or suffocating Proper use The chain is designed exclusively for sawing wood You may only fell trees if you have received the appropriate training The manufacturer cannot be held liable for damage caused by improper or incorrect usage The equipment is to be used only for its prescribed purpose Any other use is deemed to be a case of misuse The user operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this Please note that our equipment has not been designed for use in commercial trade or industrial applications Our warranty will be voided if the machine is used in commercial trade or industrial businesses or for equivalent purposes AFTER SALES SUPPORT A 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 Assembly and Parts List 3 Assembly and Parts List Layout see Fig 4 1 Chain bar 2 Saw chain 3 Chain tensioning wheel 4 Spiked bumper 5 Chain brake lever front hand guard 6 Front handle 7 Starter handle 8 Screwdriver oil pump adjusting 9 Air filter cover 10 Stop swi
29. rds Contact with the rotating saw chain cutting hazards Unforeseen abrupt movement of the guide bar cutting hazards Flung parts from the saw chain cutting ejection hazards Flung parts of the work piece ejection hazards Inhalation of work piece particles or emissions of the gasoline engine Skin contact with fuel gasoline oil Loss of hearing if the required hearing protection is not used during operation The actual vibration values when operating the machine can deviate from the values given in the manual or specified by the manufacturer This can be caused by the following influencing factors which must be considered before and respectively during the operation The appliance must be used correctly The material must be cut in the correct way and handled properly The machine must be correctly maintained and adjusted The correct cutting tool must be used The sharpness of the cutting tool must be in a good condition All handles and if applicable optional vibration handles must be mounted They must be fixed correctly onto the machine 14 AFTER SALES SUPPORT 74 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 Assembly and Parts List Before starting the equipment Do not start the engine until the saw is fully assembled Wear protective gloves at all times when handling the chain Fit the chain bar To ensure that the bar and the chain are supplied with oil USE ONLY THE ORIG
30. sages can be easily checked If the passages are clear the chain will automatically give off a spray of oil within seconds of starting the saw Your saw is eguipped with an automatic oiler system Automatic chain lubrication The chainsaw is equipped with an automatic oil lubrication system with a toothed wheel drive It automatically supplies the bar and the chain with the right quantity of oil The moment the engine is accelerated the oil also starts to flow through the bar plate more quickly as well The chain lubrication system has been set to its perfect adjustment at the factory If it requires adjusting take the saw to your nearest authorized after sales service outlet A setting screw for adjusting the chain lubrication Fig 25 Item D is located on the underside of the chainsaw Turning the screw counter clockwise increases the chain lubrication turning it clockwise decreases the chain lubrication To check the chain lubrication hold the chainsaw with the chain over a piece of paper and run it at full speed for a few seconds You will be able to judge the set amount of oil from the paper Chain maintenance Chain sharpening Chain sharpening requires special tools to ensure that cutters are sharpened at the correct angle and depth For the inexperienced chainsaw user we recommend that the saw chain be professionally sharpened by the nearest professional Service Centre If you feel comfortable sharpening your own saw chain
31. setting an Authorised Service Centre or starts but will not run Fouled spark plug Clean gap or replace plug Fuel filter blocked Replace fuel filter Incorrect lever position on choke Unit starts but engine has low Dirty air filter Remove clean and reinstall filter power Incorrect carburettor mixture Have carburettor adjusted by adjustment setting an Authorised Service Centre Incorrect carburettor mixture Have carburettor adjusted by Engine hesitates adjustment setting an Authorised Service Centre No power under load Incorrectly gapped spark plug Clean gap or replace plug A Incorrect carburettor mixture Have carburettor adjusted by Runs erratically adjustment setting an Authorised Service Centre Use properly mixed fuel 40 1 mixture Move to RUN position Smokes excessively Incorrect fuel mixture 1 Blunt chain 1 Sharpen or replace the chain 2 Loose chain 2 Tension the chain 3 Chain on wrong way round 3 Fit chain correct way round Poor performance when operated 1 Fill up the petrol tank 2 Completely fill the petrol tank or re position the fuel filter in the petrol tank 1 Empty petrol tank Engine dies 2 Fuel filter in the wrong position in the tank Insufficient chain 1 Top up the oil tank for the chain ae 1 Empty oil tank for the chain AN lubrication the E E 2 Clean the oil lubrication hole cutter rail and ae in the cutter bar Fig 2 Item A chai
32. sional user The chainsaw is designed for occasional use by home owners garden owners and campers and is for general work such as stump grubbing cutting firewood etc It is not designed for lengthy use If it is used for a lengthy period the vibrations it causes in the hands of the user may result in circulation problems white finger syndrome MODEL GLPC 41 2 General Information and Safety Instructions The hand arm vibration syndrome vibration white finger is a vascular disease that involves seizure like spasms of the fingers and toes The affected areas are no longer sufficiently supplied with blood and therefore appear extremely pale The frequent use of vibrating equipment may trigger nerve damage in people with an impaired circulation for example smokers diabetics Should you observe any unusual impairments interrupt your work immediately and consult a doctor Follow these instructions in order to reduce the dangers Keep your body and in particular your hands warm when working in the cold Take regular breaks and move your hands to stimulate the blood circulation during the breaks Ensure that the equipment makes the least possible vibration through regular maintenance and correctly tightened parts on the equipment Kickback may occur when the nose or tip of the guide bar touches an object or when the wood closes in and pinches the saw chain in the cut If the bar tip contacts it may cause a lig
33. tch 11 Safety lock 12 Oil tank cap 13 Fan housing 14 Fuel tank cap 15 Rear handle bootstrap 16 Chain guard 17 Choke carburettor setting 18 Bar fastening knob amp lever 19 Throttle lever 20 Chain catch 21 Fuel mixing bottle 22 Spark plug spanner AFTER SALES SUPPORT ln 01516491500 1890946244 amp www einhell co uk MODEL GLPC 41 AFTER SALES SUPPORT A 01516491500 1890946244 amp www einhell co uk MODEL GLPC 41 Assembly and Parts List 3 Proper Use The chain is designed exclusively for sawing wood You may only fell trees if you have received the appropriate training The manufacturer cannot be held liable for damage caused by improper or incorrect usage The equipment is to be used only for its prescribed purpose Any other use is deemed to be a case of misuse The user operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this Please note that our equipment has not been designed for use in commercial trade or industrial applications Our warranty will be voided if the machine is used in commercial trade or industrial businesses or for equivalent purposes Residual Risks Even with the intended use of the appliance there is always a residual risk which cannot be prevented According to the type and construction of the appliance the following potential hazards might appear Contact with exposed saw teeth of the saw chain cutting haza
34. the tension in the wood fibres is released Keep the handles dry clean and free of oil or fuel mixture Operate the chainsaw only in well ventilated areas DO NOT operate a chainsaw in a tree All chainsaw service other than the items listed in the user manual safety and maintenance instructions should be performed by competent chainsaw service personnel When transporting your chainsaw always fit the chain guard over the bar and chain DO NOT operate your chainsaw near or around flammable liquids or gases whether in or out of doors An explosion and or fire may result DO NOT attempt to fill the fuel tank add oil or lubrication when the engine is running USE THE RIGHT TOOL Cut wood only Do not use the chainsaw for purposes for which it was not intended For example do not use the chainsaw for cutting plastic masonry or non building materials The engine will create toxic exhaust fumes as soon as the engine is started Never work in enclosed rooms or in rooms with poor ventilation Important National regulations differ in some countries and may restrict the use of the machine To detect significant damage or defects the equipment must be inspected each time before use and each time after being dropped or suffering other shocks If any liquid is spilled while filling the oil tank or the fuel tank the equipment must be cleaned to remove the spilled liquid The following information is primarily for the end user or occa
35. uk MODEL GLPC 41 AFTER SALES SUPPORT A 01516491500 1890 946244 LJ www einhell co uk MODEL GLPC 41 AFTER SALES SUPPORT ZA 01516491500 G 1890 946244 Instructions 6 Bucking Bucking is cutting a fallen log into lengths Make sure you have a good footing and stand uphill of the log when cutting on sloping ground If possible the log should be supported so that the end to be cut off is not resting on the ground If the log is supported at both ends and you must cut in the middle make a downward cut halfway through the log and then make the undercut This will prevent the log from pinching the bar and chain Be careful that the chain does not cut into the ground when bucking as this causes rapid dulling of the chain When bucking on a slope always stand on the uphill side 1 Log supported along entire length Cut from top overbuck being careful to avoid cutting into the ground Fig 18A 2 Log supported on 1 end First cut from bottom underbuck 1 3 diameter of log to avoid splintering Second cut from above overbuck to meet first cut and avoid pinching Fig 18B 3 Log supported on both ends First overbuck 1 3 diameter of log to avoid splintering Second underbuck to meet first cut and avoid pinching Fig 180 The best way to hold a log while bucking is to use a sawhorse When this is not possible the log should be raised and supported by the limb stumps or by using supporting logs Be sure the log being cut
36. while saw is running CHAIN BRAKE is a safety feature designed to reduce the possibility of injury due to kickback by stopping a moving saw chain in milliseconds It is activated by the CHAIN BRAKE lever STOP SWITCH immediately stops the engine when tripped Stop switch must be pushed to ON position to start or restart the engine SAFETY TRIGGER prevents accidental acceleration of the engine Throttle trigger 19 cannot be squeezed unless the safety latch is depressed CHAIN CATCHER reduces the danger of injury in the event saw chain breaks or derails during operation The chain catcher is designed to intercept a whipping chain Study your saw and be familiar with its parts AFTER SALES SUPPORT A 01516491500 1890 946244 LJ www einhell co uk MODEL GLPC 41 2 General Information and Safety Instructions Items supplied Please check to ensure that you have all the items see Fig 4 before you discard the packaging Please note that the chain and chain bar are supplied separately in the box If parts are missing please contact our service centre or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase Also refer to the warranty table in the service information at the end of the operating instructions Open the packaging and take out the equipment with care Remove the packaging material and any packaging and o
37. witch it off immediately and free it carefully Finally check the equipment for damage e g a bent chain bar and carry out a test run 9 AFTER SALES SUPPORT Z 01516491500 1890946244 LJ www einhell co uk MODEL GLPC 41 10 11 20 General Information and Safety Instructions 2 Danger When using the equipment a few safety precautions must be observed to avoid injuries and damage Please read the complete operating instructions and safety regulations with due care Keep this manual in a safe place so that the information is available at all times If you give the equipment to any other person hand over these operating instructions and safety regulations as well We cannot accept any liability for damage or accidents which arise due to a failure to follow these safety regulations and instructions Safety regulations The corresponding safety information can be found in this booklet Read all safety regulations and instructions Any errors made in following the safety regulations and instructions may result in an electric shock fire and or serious injury Keep all safety regulations and instructions in a safe place for future use Safety features Fig 4 LOW KICKBACK SAW CHAIN helps significantly reduce kickback or the intensity of kickback due to specially designed depth gauges and guard links CHAIN BRAKE LEVER HAND GUARD protects the operator s left hand in the event it slips off the front handle
Download Pdf Manuals
Related Search