CMT6104 IDE Controller and Hard Drive Carrier utilityModule User`s
Contents
1. You may need to run the setup program for your cpuModule or computer to configure the correct hard drive type This mode duplicates the operation of previous versions of the CMT6104 The PC 104 bus only provides power to the drive The board performs a physical interface between the 68 pin PCMCIA connector and the 40 pin IDE connector The A or B jumpers select master or slave mode for the drive This mode decodes the PC 104 bus to create an IDE interface This interface can be the primary or secondary interface and the drive can be a master or slave as per the jumpers The 40 pin IDE connector is used to connect a second drive to this interface The second drive can be a standard 3 5 drive or another CMT6104 operating in IDE mode CMT6104 IDE Controller utilityModule 12 Real Time Devices USA Inc User s Manual Power Protection Circuitry To reduce the risk of damage due to power supply problems the utilityModule includes several protective components Module Power Supply Protection The utilityModule includes components to help prevent damage due to problems with the 5Vdc power supply from the PC 104 bus or power supply connector Protection is provided for e Over current e Reversed polarity Excessive voltage This protection is only for the utilityModule and will not protect other devices in a PC 104 stack or any of the Flat Panel power supplies The protective fuse is replaceable and is available from electronics suppli2. the factory for an RMA number THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY PRODUCTS WHICH HAVE BEEN DAMAGED AS A RESULT OF ACCIDENT MISUSE ABUSE such as use of incorrect input voltages improper or insufficient ventilation failure to follow the operating instructions that are provided by RTD Embedded Technologies acts of God or other contingencies beyond the control of RTD Embedded Technologies OR AS A RESULT OF SERVICE OR MODIFICATION BY ANYONE OTHER THAN RTD Embedded Technologies EXCEPT AS EXPRESSLY SET FORTH ABOVE NO OTHER WARRANTIES ARE EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND RTD Embedded Technologies EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED HEREIN ALL IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES FOR MECHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THIS WARRANTY IN THE EVENT THE PRODUCT IS NOT FREE FROM DEFECTS AS WARRANTED ABOVE THE PURCHASER S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT AS PROVIDED ABOVE UNDER NO CIRCUMSTANCES WILL RTD Embedded Technologies BE LIABLE TO THE PURCHASER OR ANY USER FOR ANY DAMAGES INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES EXPENSES LOST PROFITS LOST SAVINGS OR OTHER DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS AND SO
3. you will connect the PC 104 bus connector with the matching connector of another module Recommended Procedure We recommend you follow the procedure below to ensure that stacking of the modules does not damage connectors or electronics e Turn off power to the PC 104 system or stack e Select and install standoffs to properly position the utilityModule on the PC 104 stack e Touch a grounded metal part of the stack to discharge any buildup of static electricity e Remove the utilityModule from its anti static bag e Check that keying pins in the PC 104 bus connector are properly positioned e Check the stacking order make sure an XT bus card will not be placed between two AT bus cards or it will interrupt the AT bus signals e Hold the utilityModule by its edges and orient it so the bus connector pins line up with the matching connector on the stack e Gently and evenly press the utilityModule onto the PC 104 stack CAUTION Do not force the module onto the stack Wiggling the module or applying too much force may damage it If the module does not readily press into place remove it check for bent pins or out of place keying pins and try again CMT6104 IDE Controller utilityModule 7 Real Time Devices USA Inc Finding Pin I of Connectors Chapter 4 CONNECTING THE UTILITYMODULE The following sections describe connectors of the utilityModule Finding Pin 1 of Connectors A white area silk screened on the PC board indicates t
4. 6 IRQ3 5 DACK2 3 2 0 5 5 5 5 5 5 T 5 5 B SAI S OV ov AAA D D D D D D D A A A A A A A A A OV SV OV OV 9 Real Time Devices USA Inc IDE Connector CN3 PC 104 AT Bus Connector CN2 Row C 0V SBHE LA23 IOCS16 RowD MEMCSI6 LA22 LA21 LA20 LAI9 LAIS LAI7 MEMR MEMW SD8 SD9 SD10 SDII SD12 SD13 SD14 5015 KEYING PIN Note Two locations on the bus have mechanical keying pins to help prevent misconnection of the PC 104 bus These keying pins are a part of the PC 104 standard and we strongly recommend you leave them in place If you have other modules without keying pins we suggest you modify them to include keying IDE Connector CN3 CN3 is a 40 pin 0 1 DIL connector is the IDE input connector in IDE mode and the IDE output in BUS mode The pinout of this connector is shown below IDE Hard Drive Connector CN3 Pin Signal Function RESET 2 GND Ground signal HD data 7 HD data 8 HD data 6 N HB HD data 9 HD data 5 8 HDIO HD data 10 9 mm HD data 4 HD11 HD data 11 CMT6104 IDE Controller utilityModule Real Time Devices USA Inc User s Manual HD data 3 HD data 12 HD data 2 HD data 13 HD data 1 HD data 14 HD data 0 HD data 15 Ground signal Address Enable Ground signal I O Write Ground signal I O Read Ground signal IOCHRDY Channel Ready Bus Address Lat
5. CMT6104 IDE Controller and Hard Drive Carrier utilityModule User s Manual RTD Embedded Technologies Inc Real Time Devices Accessing the Analog World BDM 610020013 1509001 and AS9100 Certified CMT6104 IDE Controller and Hard Drive Carrier utilityModule User s Manual RTD Embedded Technologies INC 103 Innovation Blvd State College PA 16803 0906 Phone 1 814 234 8087 FAX 1 814 234 5218 E mail sales rtd com techsupport rtd com web site http www rtd com Revision History Rev A New manual naming method Published by RTD Embedded Technologies Inc 103 Innovation Blvd State College PA 16803 0906 Copyright 1999 2002 2003 by RTD Embedded Technologies Inc All rights reserved Printed in U S A The RTD Logo is a registered trademark of RTD Embedded Technologies cpuModule and utilityModule are trademarks of RTD Embedded Technologies PhoenixPICO and PheonixPICO BIOS are trademarks of Phoenix Technologies Ltd PS 2 PC XT PC AT and IBM are trademarks of International Business Machines Inc MS DOS Windows Windows 95 Windows 98 and Windows NT are trademarks of Microsoft Corp PC 104 is a registered trademark of PC 104 Consortium All other trademarks appearing in this document are the property of their respective owners TABLE OF CONTENTS CHAPTER 1 INTRODUCTION da 1 CMT6104 IDE AND HARD DRIVE CARRIER UTILITYMODULE ccccccccccnncnnnnnnnnnnnnnnnnononononononononononon
6. IDE jumper e Install SEC jumper Remove PRI jumper e Install jumper A select master for Integral drives and install jumper B to select master for SanDisk drives e Use CPU s setup utility to configure the heads cylinders and sectors for the drive Using a CMT6104 as a slave drive Install IDE jumper e Remove BUS jumper e Install PRI jumper Not used since in IDE mode Remove SEC jumper Not used since in IDE mode e Connect a three connector 40 pin cable from CPU s IDE connector to the master drive and to the CMT6104 IDE connector CN3 be careful to observe pin I orientation e Install jumper B select salve for Integral drives or install jumper A to select slave for SanDisk drives e Use CPU s setup utility to configure the heads cylinders and sectors for the drive CMT6104 IDE Controller utilityModule 14 Real Time Devices USA Inc User s Manual CMT6104 IDE Controller utilityModule 15 Real Time Devices USA Inc Return Policy Chapter RETURN POLICY AND WARRENTY Return Policy If you wish to return a product to the factory for service please follow this procedure Read the Limited Warranty to familiarize yourself with our warranty policy Contact the factory for a Return Merchandise Authorization RMA number Please have the following available Complete board name Board serial number A detailed description of the board s behavior List the name of a contact person familiar with technical det
7. ME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE CMT6104 IDE Controller utilityModule 18 Real Time Devices USA Inc CMT6104 IDE Controller utilityModule RTD Embedded Technologies Inc 103 Innovation Blvd State College PA 16803 0906 USA Our website www rtd com User s Manual Real Time Devices USA Inc
8. ails of the problem or situation along with their phone and fax numbers address and e mail address if available List your shipping address Indicate the shipping method you would like used to return the product to you We will not ship by next day service without your pre approval Carefully package the product using proper anti static packaging Write the RMA number in large 1 letters on the outside of the package Return the package to RTD Embedded Technologies Inc 103 Innovation Blvd State College PA 16803 0906 USA CMT6104 IDE Controller utilityModule 16 Real Time Devices USA Inc User s Manual CMT6104 IDE Controller utilityModule 17 Real Time Devices USA Inc Return Policy LIMITED WARRANTY RTD Embedded Technologies Inc warrants the hardware and software products it manufactures and produces to be free from defects in materials and workmanship for one year following the date of shipment from RTD Embedded Technologies INC This warranty is limited to the original purchaser of product and is not transferable During the one year warranty period RTD Embedded Technologies will repair or replace at its option any defective products or parts at no additional charge provided that the product is returned shipping prepaid to RTD Embedded Technologies All replaced parts and products become the property of RTD Embedded Technologies Before returning any product for repair customers are required to contact
9. ash drives such as SanDisk Jumper selection of bus or cabled operation e Bus mode decodes IDE interface through the PC 104 bus for cableless operation e IDE mode attaches drive to a cpuModules IDE interface and to attach a slave to a master drive Jumper selection of primary or secondary IDE interface in bus mode e Primary IDE Interface at 1F0 1F7h e Secondary IDE Interface at 170 177h Jumper selection of master or slave drive e Master for the first drive on each interface e Slave for the second drive on each interface Connectors Connectors provided are e PC 104 Bus XT e CN2 PC 104 Bus AT e CN3 IDE hard drive e PCMCIA ATA connector CMT6104 IDE Controller utilityModule 1 Real Time Devices USA Inc Recommended Cables Recommended Cables e 40 pin IDE cable which can be used to connect a master CMT6104 to a slave CMT6104 General Specifications Dimensions 3 8 x 3 9 x 0 6 97 x 100 x 16 mm e Weight mass 3 0 ounces 85 grams e 4 Jayer PCB e Operating conditions not including drive temperature 40 85 degrees C relative humidity 0 95 non condensing Storage temperature 55 to 85 degrees C CMT6104 IDE Controller utilityModule 2 Real Time Devices USA Inc User s Manual CMT6104 IDE Controller utilityModule 3 Real Time Devices USA Inc Jumpers Chapter 2 CONFIGURING THE UTILITYMODULE The following sections contain information on configur
10. ch Enable Ground signal MONS oo w gt egg tri Interrupt Request IOCS 16 16 bit transfer Address 1 GND Ground signal Address 0 Address 2 HD Select 0 HD Select 1 HDD activity LED Ground signal BRIO cala CN4 The 68 pin PCMCIA ATA connector is to connect hard drives and Flash ATA cards This is not full PCMCIA interface and only works with ATA drives like the Integral Viper series and the SanDisk Flash Drives with True IDE mode CMT6104 IDE Controller utilityModule 11 Real Time Devices USA Inc IDE Hard Disk Chapter 5 USING THE UTILITYMODULE IDE Hard Disk IDE Mode BUS Mode In general IBM PC computers support two IDE interfaces Each interface can support a master and a slave IDE drive which allows up to 4 drives in a computer assuming that the CPU BIOS supports 4 drives The CMT6104 operates as a drive carrier to convert the PCMCIA connector to the standard 40 pin IDE connector and provide a master slave jumper It can also be an IDE controller for computers without an IDE interface or to add a secondary IDE interface to a computer that only has one These two modes of operation are selected by installing one of the IDE or BUS jumpers The hard drive controller of the utilityModule appears as a standard PC IDE hard drive controller It will support standard IDE drives less than 528MB and enhanced IDE drives over 528MB
11. ers Its description and part number are Littelfuse Nano SMF 1 0 amp R451 001 Caution Replace fuses only with parts of identical current and voltage rating CMT6104 IDE Controller utilityModule 13 Real Time Devices USA Inc Connecting the CMT6104 to a computer with an IDE controller as the only IDE drive Chapter 6 INTERFACING IDE DRIVES The utilityModule can be configured in several methods Connecting the CMT6104 to a computer with an IDE controller as the only IDE drive e Install IDE jumper e Remove BUS jumper e Install PRI jumper Not used since in IDE mode e Remove SEC jumper Not used since in IDE mode e Connect a 40 pin cable from CPU s IDE connector to the CMT6104 IDE connector CN3 be careful to observe pin 1 orientation e Install jumper A select master for Integral drives or install jumper B to select master for SanDisk drives e Use the CPU s setup utility to configure the heads cylinders and sectors for the drive Connecting the CMT6104 to a computer without an IDE controller as the only IDE drive e Install BUS jumper Remove IDE jumper e Install PRI jumper Remove SEC jumper Install jumper A select master for Integral drives or install jumper B to select master for SanDisk drives e Use CPU s setup utility to configure the heads cylinders and sectors for the drive Connecting the CMT6104 to a computer as the secondary IDE drive controller e Install BUS jumper Remove
12. he pin 1 end of connectors A square solder pad visible on the bottom of the PC board also indicates it Please make certain you have correctly identified pin 1 of connector before you connect to it and attempt to use the utilityModule Connector Locations The figure below shows connector locations JP2 E me CMT184 utilityModule WARNING his card is not g PCMCIA PC Card slot it is only Mor use with ATA drives ith an IDE interface CN3 CN1 CN2 Connector Locations Connectors Connector Function Size CNI PC 104 XT Bus 64 pin CN2 PC 104 AT Bus 40 pin CN3 IDE Connector 40 pin CN4 PCMCIA ATA Connector 68 pin JP2 IDE Activity LED Connector 2 pin CMT6104 IDE Controller utilityModule 8 Real Time Devices USA Inc PC 104 Bus Connectors CN1 and CN2 Connectors CN1 and CN2 provide PC 104 bus connections CN1 carries XT bus signals and CN2 carries additional signals for the AT bus The signals on CN1 and CN2 conform to the IEEE P966 User s Manual standard for the PC 104 bus The following tables list the connector pinouts 3 CMT6104 IDE Controller utilityModule PC 104 XT Bus Connector CN1 RESETDRV 5 5 5 5 5 5 SDI 5 IOCHRDY AEN 4 5 19 n gt oo SA17 SAI6 Nn gt SA14 DACKI DRQI SA13 SA12 REFRESH SYSCLK SA11 7 6 5 4 3 2 0 SA10 IRQ7 9 IRQ6 8 IRQ5 7 IRQ4
13. ing the utilityModule Please read this entire section before attempting to use the utilityModule Jumpers Jumper JP1 configures the following functions e Master Slave e Bus Cabled e Primary Secondary Default Settings The utilityModule is delivered from the factory configured according to the following table Setting A with Integral Drive B with Integral Drive A with SanDisk Drive B with SanDisk Drive BUS Decode IDE Through PC 104 bus IDE Use CN3 for IDE interface If BUS mode is selected then PRI Primary IDE interface SEC Secondary IDE interface Notes 1 You must select only one of A or B 2 You must select only one of BUS or IDE 3 If you have selected BUS you must select only one of PRI or SEC CMT6104 IDE Controller utilityModule 4 Real Time Devices USA Inc User s Manual Jumper Locations The figure below shows jumper locations Jumper 4 2 J P1 5 IAE Accessing the Analog World qp CMT104 utilityModule M WARNING his card is not PCMCIA PC Cord slot It is only use with ATA drives ith an IDE interface CMT6104 IDE Controller utilityModule 5 Real Time Devices USA Inc Jumpers CMT6104 IDE Controller utilityModule 6 Real Time Devices USA Inc User s Manual Chapter 3 INSTALLING THE UTILITYMODULE Since the utilityModule uses a PC 104 stackthrough bus the only hardware installation you will do is placing the module to the PC 104 stack To do this
14. onononononononnnnnnnanononon 1 BEATURES MS ehe Ne ae Besen m Mete LE eet 1 CONNECTORS verserer tr retrett 1 RECOMMENDED CABLES 3 ee veh ins de 2 GENERAL SPECIEICATIONS p aaa een eee eu 2 CHAPTER 2 CONFIGURING THE UTILITYMODULE essossssssssvsssvsssssssvsssssssvssssssssseruserssersserusernsersser 4 JUMPERS une 4 Def ilt Settings 4 Jumper eo oe ete pr een pam iiit tenete ids ien Diete pius 5 CHAPTER 3 INSTALLING THE UTILITYMODULE eessosssessreessevsreverevessvsrsvssssersvsssessesssssssesssesssssssesere 7 RECOMMENDED PROCEDURE aria 7 CHAPTER 4 CONNECTING THE UTILITYMODULE ssossssssssssssssssssssssssssssssssssssssssssensssnsssnssensssnsssssser 8 FINDING PIN 1 OF CONNECTORS ers ar ideer bene ee ee Res 8 Connector EOCanonsia sn Sinne rette ok EE aie ec a eet d 8 CONNECTORS us 8 PC 104 BUS CONNECTORS AND CN2 s a a a aaa E E SEEEN aa 9 IDECONNECTOR ENS isen rende ere Aae an e 10 PECMCIA ATACN4 see ns ane dnb esse res 11 CHAPTER 5 USING THE UTILITYMODULE sessesssssssssereverusereseressrsserusereserssereserusersseruseruserusensesenssenes 12 IDE HARD DR ane De deo ae UMEN 12 TIE MOC x9 sik do ona ee Ra aa 12 BUS Modest le 12 Module PoWer Supply Protection Jus a Se ANER 13 CHAPTER 6 INTERFACING IDE DRIVES sossssssvssssrsssrsseresereversserussrssereseresers
15. serssersserssersssessssssssnssesssenes 14 CONNECTING THE CMT6104 TO A COMPUTER WITH AN IDE CONTROLLER AS THE ONLY IDE 14 CONNECTING THE CMT6104 TO A COMPUTER WITHOUT AN IDE CONTROLLER AS THE ONLY IDE DRIVE 14 CONNECTING THE CMT6104 TO A COMPUTER AS THE SECONDARY IDE DRIVE 14 USING A CMT6104 AS A SLAVE DRIVE eee e e e e e e n n nnn nnn nn nnn nn nnn nna na np 14 CHAPTER 7 RETURN POLICY AND WARRENTY seseresssrsssrssssssssssssssssssssssssssssnsssnsssnssensssnsssnsssnsssnes 16 RETURNPOLIGY re ee 16 LIMITED n 18 User s Manual Chapter 1 INTRODUCTION This manual gives information on the CMT6104 IDE Controller and Hard Disk Carrier utilityModule This module converts PCMCIA ATA hard drives and Flash Drives that can operate in IDE mode to a standard IDE interface CMT6104 IDE and Hard Drive Carrier utilityModule The CMT6104 utilityModule was designed to provide an IDE hard drive or Flash drive in the PC 104 stack to support the Real Time Devices family of cpuModules and other standard PC 104 processor modules Features The following are major features of the CMT6104 utilityModule Allows up to four drives in the PC 104 stack Supports PCMCIA ATA drives such as the Integral Viper series and Fl
Download Pdf Manuals
Related Search