IP5-Manual-Generalized
Contents
1. not allow the water and other liquid falling into the camera Thunder proof device is recommended to be adopted to better prevent thunder The grounding studs of the product are recommended to be grounded to further enhance the reliability of the camera 6 Daily Maintenance Please shut down the device and then unplug the power cable before you begin daily maintenance work Do not touch the CCD CMOS optic component You can use the blower to clean the dust on the lens surface Always use the dry soft cloth to clean the device If there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device Please put the dustproof cap to protect the CCD CMOS component when you do not use the camera 7 Accessories Be sure to use all the accessories recommended by manufacturer Before installation please open the package and check all the components are included Contact your local retailer ASAP if something is broken in your package Accessory Name IP Camera Unit Table of Contents 1 General Introduction 1 1 Overview 1 2 Features 1 3 Camera Installation 1 4 Varifocal lens 2 Structure 2 1 Multiple function Combination Cable 2 2 Framework and Dimension 4 Quick Configuration Tool 4 1 OLY Be ae bore Ede LM E E E NE E A ERR ee mE 1 General Introduction 1 1 Overview This series IP camera integrates the traditiona2. IP Network Camera Waterproof IR IP Network Camera IP Network Sa ty Welcome Thank you for purchasing our IP camera This user s manual is designed to be a reference tool for your system Please read the following safeguard and warnings carefully before you use this series product Please keep this user s manual well for future reference Our units do not support PAL Important To find your cameras on the network use the config Tool found in the CD under Software gt ConfigTool that came with your package Some cameras will be assigned as a DHCP Therehore The IP Config Tool is required to find the camera on the network DO NOT Connect all the cameras on the same network at the same time This will cause IP conflict within your network and you will not be able to accress your cameras Before connecting all the of the IP cameras on the network One At A Time DO NOT power the camera with both PoE and a power supply at the same time If you purchase a PoE Power Over Ethernet device from us Whether as an External POE Switch or built into on of our NVRs your camera Will be powered through the Ethernet cable and will not need to power it with a seperate power supply Restrictions may apply Important Safeguards and Warnings 1 Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Vo
3. PC IP address and PC IP address shall be in the same network segment if there is no router IPC default IP address is 192 168 1 108 or DHCP If there is a router please set the corresponding gateway and subnet mask The factory default user name is admin and password is admin For security reasons please modify your password after you first login For detailed WEB operation please refer to the IPC Web Operation Manual in the resource CD 2 Configtool 1 0 5 Device List SN IP Address Port Subnet Mask Default Gateway Mac a Ee Wer 37777 255 255 255 0 192 168 30 0 Open Device Web 108 per Tip You can click login button directly and then input corresponding information to login A11 v Upgrade Refresh Login Logout Figure 3 2 Select the Open Device Web item you can go to the corresponding web login interface See Figure 3 3 A WEB SERVICE Windows Internet Explorer File Edit View Favorites Tools Help Q e eJ ix a po Search Pe Favorites 2 e M i rel Address http 192 168 1 108 WEB SERVICE Username Password me cae Local intranet Figure 3 3 If you want to modify the device IP address without logging in the device web interface you can go to the configuration tool main interface to set In the configuration tool search interface Figure 3 1 please select a device IP address and then double click it to open th
4. a Sun Shield Cover ere 5 ae CL c a A 8 es d A s p T r or e 9 OW ad P 20 OA J SE gt A A Before you install the bracket please pull the cable through the cable exit of the bracket chassis Important The installation wall shall min sustain 3X weight of the bracket and camera Step 1 Paste the installation map on the surface of the wall or the ceiling Step 2 Dig the installation holes according to the installation map No Name Step 3 Open the accessories bag and then take the expansion bolt out Insert the expansion bolt into the installation holes Step 4 Take the screws from the accessories bag and then use them to secure the device on the installation surface of the wall or the ceiling The sun shield of the device can move forward or backward Please secure the set screw of the sun shield after you fixed the device Step 5 Connect the corresponding cables Step 6 Use the cross head screwdriver to loosen the adjust screw Step 7 Turn the device in different directions to make it suitable for the monitor position Step 8 Use the cross head screwdriver to fix the adjust screw firmly Adjust Screw 1 4 Variofocal lens In other cameras the adjustable lever can be found in the inside of the camera Each camera will be a little different Some adjustable lens cameras are adjusted manually on the camera illii VariFocal Camera Unsc
5. assword There is no player There is no DX8 1 or higher For the MEDIA PLAYER there shall be Div X503Bundle exe plugin if you play the AVI file For Windows XP user you need to install the plugin DivX503Bundle exe and ffdsho 2004 1012 exe After you modified the important setup please reboot the device via the software to make sure the setup has been updated to the storage medium The power adapter included in the accessories bag can work ranging from O C to 40 C The device may result in unstable power supply when the temperature exceeds the working temperature Please replace an industry level power adapter if you are using in the harsh environments Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Component Device Construction Material PF 2 2 fs ef es Com gg 3 O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T11363 2006 standard During the environmental friendly use period EFUP period the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these substances or elements will not result in any severe environmental p
6. e control When system is upgrading it can overwrite the previous Web too If you can t download the ActiveX file please check whether you have installed the plug in to disable the control download Or you can lower the IE security level internet Options aa e ee General Security Privacy Content Connections Programs Advanced Settings 4 Binary and script behaviors Select a zone bo view or change security settings 2 4 d C Administrator approved a Jf Le Disable w m Enable Internet Local intranet Trusted sites a Display video and animation on a webpage that does not use gt Disable Internet Enable This zone is For Internet websites altes i Download signed Actives controls except those listed in trusted and Disable restricted zones Enable not secure Security level For this zone 4 Download unsigned Actives controls Allowed levels For this zone Medium to High oa d DM 3 Enable not secure 2 Medium high 9 Prompt Appropriate For mast websites 1 TniFialize And errinF AcFive cankele npk marked az cake For or Prompts before downloading potentially unsafe k content Unsigned Actives controls will nat be downloaded Takes effect after you restart Internet Explorer Reset custom settings Reset to Medium high default Reset Custom level Default level Reset all zones to default level Cancel Pie LE Yew P
7. e login interface Or you can select an IP address and then click the Login button to go to the login interface See Figure 3 4 In Figure 3 4 you can view device IP address user name password and port Please modify the corresponding information to login Please note the port information here shall be identical with the port value you set in TCP port in Web Network interface Otherwise you can not login the device If you are use device background upgrade port 3800 to login other setups are all invalid IP Address 192 168 1 1 08 User Name FERE Password Port 3777 oa Figure 3 4 After you logged in the configuration tool main interface is shown as below See Figure 3 5 X ConfigTool V1 0 5 NetWork Parameter PPPOE System T tormatieni System Upgrade gt General Parameter I DHcP Enable P4 E IP Address 1921681108 Subnet Mask 255 255 255 0 Gateway 19216 00000000 Mac Address p0 02 a9 00 76 83 000000 Figure 3 5 For detailed information and operation instruction of the quick configuration tool please refer to the Quick Configuration Tool User s Manual included in the resources CD 4 Web Operation This series IPC product support the Web access and management via PC Web includes several modules includes monitor channel preview system configuration alarm and etc 4 1 Network Connection Please follow the steps listed below for network con
8. eeded Network e Max supports 20 connections Monitor Adopt the following video transmission protocol HTTP TCP UDP MULTICAST RTP RTCP RTSP and etc e Support web access Network e Realize IPC configuration and management via Ethernet Management 9 Support device management via web or client end External power adapter DC 12V e Support PoE Warning Do not connect these two power supplying sources to the device at the same time it may result in device damage Log function Support system resource information and running status real time display Day Night mode auto switch Support picture parameter setup such as electronic shutter and gain setup Assistant Support motion detect Function Backlight compensation screen auto split to realize backlight compensation to adjust the bright Support video watermark function to avoid vicious video modification Built in IR light Support IR night vision The enclosure conforms to the IP 66 protection Has the waterproof function 1 3 Camera Installation Dome Installation Step 1 If included please take the installation position map from the accessories bag and then paste it on the ceiling or the wall according to your monitoring area requirements Draw and then drill holes in the installation surface and then insert expansion anchor bolts in the holes Secure these bolts firmly Step 2 Turn counter clockwise to remove the decoration ring plastic housing turn the pan base to
9. eoia Toss Hep Qe O dig fh Omn rne O G a m a Adress EE Edo wma WEB SERVICE Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction o FAQ can not boot up the device or operate properly The water leakage occurred IR video is poor can not upgrade the device via network can not login the client end or the WEB can not play the download file To guarantee setup update Power adapter Please click RESET button for at least five seconds to restore factory default setup The unauthorized front or rear cap remove many result in water leakage The glass front cap has sustained heavy push or strike The waterproof plug of the rear cap becomes loosen Do not use the proper supplying power The IR light can not turn on completely The object is out of the IR distance range of current device IR CUT does not turn to the night mode The photosensitive chip of the front end can not sense the IR light When network upgrade operation failed you can use port 3800 to continue upgrade For Windows OS 98 or Windows ME user if you can not install the client end or can not view after the installation We recommend the win2000sp4 OS or install the client end of the low version The Active X control is blocked The display card version shall be dx8 1 or higher Network connection error occurred Invalid network setup Invalid user name or p
10. l camera and network video technology It adopts video data collection transmission together It can connect to the network directly without any auxiliary device This series IPC uses standard H 264 video compression technology which maximally guarantees the video quality It supports the IR night vision function In the night environments the device can use the IR light to highlight the object which is suitable for the surveillance function in the low illumination environments The waterproof design conforms to the IP 66 level It has the sound waterproof function suitable for use in the outdoor environments It can be used alone or used in a network area When it is used lonely you can connect it to the network and then use a network client end Due to its multiple functions and various uses this series IPC is widely used in many environments such as an office bank road monitor and etc 1 2 Features tier Different user rights for each group one user belongs to one group The user right shall not exceed the group right Management e Support central server backup function in accordance with your configuration Storage and setup in alarm or schedule setting e Support record via Web and the recorded file are storage in the client end Function PC e Support network storage function such as FTP PC supports one channel video data transmit to network terminal and then decode Delaying time is within 270ms network bandwidth support n
11. ltage and the Limited power source is rated 12V DC in the IEC60950 1 This series product supports PoE too Please note Do not connect these two power supplying sources to the device at the same time it may result in device damage We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation We are not liable for any problems caused by unauthorized modification or attempted repair 2 Transportation security Heavy stress violent vibration or water splash are not allowed during transportation storage and installation 3 Installation Do not apply power to the camera before completing installation Please install the proper power cut off device during the installation connection Always follow the instruction guide the manufacturer recommended 4 Qualified engineers needed All the examination and repair work should be done by the qualified service engineers We are not liable for any problems caused by unauthorized modifications or attempted repair 5 Environment This series IP camera should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc Please keep it away from the electromagnetic radiation object and environment Please make sure the CCD CMOS component is out of the radiation of the laser beam device Otherwise it may result in CCD CMOS optical component damage Please keep the sound ventilation Do
12. nection Make sure the IPC has connected to the network properly Please set the IP address subnet mask and gateway of the PC and the IPC respectively IPC default IP address is 192 168 1 108 or DHCP Subnet mask is 255 255 255 0 Gateway is 192 168 1 1 Use order ping IP camera address to check connection is OK or not 4 2 Login and Logout Open IE and input IP camera address in the address bar For example if your camera IP is 192 168 1 108 then please input http 192 168 1 108 in IE address bar Blank Page Windows Internet Explorer Gs E abak 5 gt Input your IP amp mw we Blank Page Fw amp mh i Page of Tools s address here Internet A100 Sere The login interface is shown as below Please input your user name and password Default factory name is admin and password is admin Note For security reasons please modify your password after you first login A WEB SERVICE Windows Internet Explorer File Edit View Favorites Tools Help Q e eJ ix a 5 p gt Search Pe Favortes g Y LJ id Address http 192 168 1 108 WEB SERVICE Username Password Local intranet If it is your first time to login in system pops up warning information to ask you whether install control webrec cab or not after you logged in for one minute Please click OK button system can automatically install th
13. ollution any bodily injury or damage to any assets The consumer is not authorized to process such kind of substances or elements please return to the corresponding local authorities to process according to your local government statutes Note This user s manual is for reference only Slight difference may be found in user interface All the designs and software here are subject to change without prior written notice e If there is any uncertainty or controversy please refer to the final explanation of us e Please visit our website for more information
14. rew M2 5 5 Bolt from the lower cover of the camera Remove the Cover and adjust the VariFocal zoom to your preference M Lens Focal Lens Lower Cover M2 5 5 Bolt 2 1 Multiple function Combination Cable You can refer to the following figure for multiple function combination cable information See Figure 2 1 Figure 2 1 Please refer to the Corn re sheet for detailed J 1 LAN Network port ea Connect to standard Ethernet cable 2 DC12V bea EHE Power input port Input DC 12V 3 Quick Configuration Tool 3 1 Overview Quick configuration tool can search current IP address modify IP address At the same time you can use it to upgrade the device Please note the tool only applies to the IP addresses in the same segment 3 2 Operation Double click the ConfigTools exe icon you can see an interface is shown as in Figure 3 1 In the device list interface you can view device IP address port number subnet mask default gateway MAC address and etc css Configiool AI URS Device List SN IP Address Port Subnet Mask Default Gateway Mac Address 1 192 188 1 108 3TTTT 255 255 255 0 192 168 1 1 90 02 a9 Tb 50 amp Tip You can cli then input correspondi A11 M Figure 3 1 Select one IP address and then right click mouse you can see an interface is shown as in Figure 3 2 Note You can set the IP address subnet mask and gateway for the IPC and PC Please note I
15. the pedestal to loosen or secure firmly metal housing or Use the inner hex wrench to remove the three enclosure fastening screws and then remove the dome enclosure glass enclousure Adjust the pedestal position according to the cable exit move ceiling side Pull the cable through the cable side exit at the installation surface and the pedestal Please skip this step if you are mounting on a ceiling Line up the screw holes at the bottom of the pedestal to the expansion bolts in the installation surface Put three self tapping screws to expansion bolts and then secure firmly Now the pedestal is on installation surface Plastic Housing mu Ceiling or Wall Expansion Bolt Dome Camera Body ST3 Self tapping Screws Decoration Ring Metal Housing Ceiling or Wall Expansion Bolt Pedistal 1 l ST3 Self tapping Screws Glass Enclosure Ceiling or Wall Installation Position Map Expansion Bolts Enclosure fastening screw Socket Screw Inner Hex Wrench Box Camera Lens Installation Auto Aperture Lens Please follow the steps listed below for auto aperture lens installation e Remove the CCD protection cap of the device and then line up the lens to the proper installation position Turn clockwise until the lens is fixed firmly Insert the lens cable socket to the auto lens connector in the side panel Adjust focus length Bullet Installation
Download Pdf Manuals
Related Search
IP5 Manual Generalized