User Manual - Viper Protection
Contents
1. Use a setup monitor while making installation setup adjustments to the camera 9 Connect the camera HDMI connector or the HD SDI connector to a DVR or monitor with HD capabilities using suitable cable 10 Connect the main cable power connector to your powering source in compliance with local codes If using 12 Vdc to power the camera ensure that the center terminal of the mating connector is positive 11 Verify that the POWER LED on the back of the camera is lit 12 Power on the local setup monitor 13 While observing the image from the camera on the monitor adjust the camera for the desired field of view a Adjust the mounting bracket to center the field of view in the camera image b Adjust the lens zoom and focus following the manufacturer s suggested method 2 Megapixel Full HD C Mount Box Camera User Manual 5 SECTION 2 INSTALLATION NOTE Ifyou installed a lens without focus adjusting mechanism or a sharper focus is needed after adjusting the lens focus Loosen the flange back back focus set screw with a hex wrench then rotate the flange until the best focus is achieved Tighten the flange back set screw until it is snug 14 Configure your camera using the software menus in the on screen display OSD Refer to SECTION 3 Configuration Setup on page 7 for more information 15 Ifyou used a setup monitor to configure the camera disconnect it from the camera SECTION 3 CONFIGURATION SETUP SE2. Camera User Manual 7 SECTION 3 CONFIGURATION SETUP 3 2 MODEL MODEL Select model type D amp N day and night COLOR IR SMART IR CDS 3 3 EXPOSURE To open the EXPOSURE menu rock the joystick down or up to highlight EXPOSURE then press the joystick down set select EXPOSURE BRIGHTNESS TITRE MODEL LENS pc EXPOSURE SHUT SPEED AUTO WHITE BAL FLICKERLESS OFF IMAGE DSS OFF MENU INTELLIGENCE AGC OFF SPECIAL FUNC WDR BLC OFF DISPLAY DAY amp NIGHT a EXIT SMART IA OFF RETURN BRIGHTNESS Adjust brightness level 0 dark 20 bright steps LENS DC MANUAL SHUT SPEED Can be set in AUTO or MANUAL AUTO 1 30 25 1 60 50 1 120 100 1 240 1 500 1 1000 1 2000 1 4000 1 8000 1 16000 1 30000 1 60000 s FLICKERLESS Set to On or Off for best video performance Normally OFF DSS Select maximum DSS Digital Slow Shutter OFF x2 x3 x4 This feature improves the video image in low light conditions AGC Select Auto Gain Control OFF ON WDR BLC Select WDR Wide Dynamic Range or BLC Back Light Compensation NOTE When WDR is ON ACE and DEFOG function will not turn on WEIGHT Adjust WDR level 0 3 BLC AREA Control BLC area according to light condition POS X Adjust the window X Axis position P0S Y Adjust the window Y Axis position S X Adjust the window X Axis size S Y Adjust the window Y Axis size DAY amp NIGHT Select Day amp Night The MODEL mode de
3. 16 APPENDIX B Camera DIMENSIONS cosas nn 17 2 Megapixel Full HD C Mount Box Camera User Manual V vi SECTION 1 INTRODUCTION SECTION 1 Introduction This high definition indoor C CS mount camera features 2 2 megapixel imaging with 1920 x 1080 resolution along with 3 dimensional Noise Reduction 3D NR 3D NR automatically provides a more accurate noise reduction This is based on twice the visual information than conventional field based types The video noise is reduced by 30 96 in low light for a 2 dB improvement in the signal to noise ratio The result is a brighter picture with less noise even in low light High definition video HDcctv security cameras deliver true 1080p or 720p HD video true HDTV quality video in live and recorded view modes A lens is not included Features 1 3 Panasonic CMOS sensor Full HD Resolution HDMI output HD SDI output SMPTE 292M Composite video out BNC DAY amp NIGHT WDR Wide Dynamic Range Defog privacy mask functions On Screen Display Intelligent motion detection Multi Protocol PELCO D PELCO P 1 1 Camera components Camera holder hole mdi upper side and underside Lens not provided Lens iris output connector Flange back set screw 2 Megapixel Full HD C Mount Box Camera User Manual 1 SECTION 1 INTRODUCTION NOTES Lens The camera accommodates a standard C or CS mount lens Camera holder hole Provided on the upper side
4. 8 x21 x25 x32 HLC Select High Light Compensation When extremely bright light is projected to the camera masking is used on the portion to prevent partial saturation on the monitor OFF ON ONLEVEL 0 20 steps COLOR Black White Yellow Cyan Green Magenta Red Blue ACE Select Digital WDR Wide Dynamic Range OFF ON NOTE When ACE is On WDR BLC and DEFOG function can not turn on SECTION 3 CONFIGURATION SETUP WDR Off WDR ON DNR Select Digital Noise Reduction AUTO OFF LOW MIDDLE HIGH D COMPRESS Use this function only with IP camera Set to OFF GAMMA Set gamma level for best display 3 6 INTELLIGENCE MENU INTELLIGENCE PRIVACY OFF RETURN MODEL EXPOSURE WHITE BAL IMAGE INTELLIGENCE SPECIAL FUNC DISPLAY EXIT PRIVACY Hide an area you want to hide on the screen OFF ON MASK Select mask area number 0 31 MODE Set up masking areas OFF ON X PQS Adjust the mask X Axis position Y P05 Adjust the mask Y Axis position X SIZ Adjust the mask X Axis size Y SIZ Adjust the mask Y Axis size COLOR Cyan Green Magenta Red Blue Black White Yellow TRANS Select mask transparency level 0 4 2 Megapixel Full HD C Mount Box Camera User Manual 11 SECTION 3 CONFIGURATION SETUP 3 7 SPECIAL FUNCTION MENU EXPOSURE WHITE BAL IMAGE INTELLIGENCE SPECIAL FUNC SHADING DET SHADING DEFECT DET DEFOG SYSTEM HD FO
5. BAL MODEL EXPOSURE WHITE BAL IMAGE AWB AUTO CHROMA HIT RU RETURN INTELLIGENCE SPECIAL FUNC DISPLAY EXIT AWB Select WHITE BALANCE mode AUTO PRESET MANUAL INDOOR OUTDOOR AUTO Automatically adjusts color according to the lighting PRESET It is a fixed white balance mode that may be automatically readjusted only by pressing PRESET MANUAL You can change WB as changing RED GAIN and BLUE GAIN in manual mode RED GAIN Adjust R gain value 0 20 BLUEGAIN Adjust B gain value 0 20 INDOOR Set color temperature to be Indoor light 3700 K OUTDOOR Set color temperature to be Outdoor light 5100 K CHROMA Adjust CHROMA gain value 0 20 steps 2 Megapixel Full HD C Mount Box Camera User Manual 9 SECTION 3 CONFIGURATION SETUP 3 5 IMAGE MENU EXPOSURE WHITE BAL IMAGE INTELLIGENCE SPECIAL FUNC DISPLAY EXIT SHARPNESS Adjust sharpness level 0 10 steps MIRROR Select a flip mode OFF H V H amp V H You can flip the picture horizontally on the screen V You can flip the picture vertically on the screen IMAGE SHARPNESS MIRROR FREEZE E ZOOM HLC ACE DNR D COMPRESS GAMMA RETURN H amp V You can flip the picture horizontally amp vertically on the screen H Mirror Off Freeze Select real or still mode OFF ON H Mirror ON E ZOOM Select maximum digital zoom magnification x1 x12 x14 x15 x1
6. BLACK BLK HDC20 2 Megapixel Full HD C mount Box Camera User Manual Please read this manual before using your camera and always follow the instructions for safety and proper use Save this manual for future reference BLK HDC20 CM N Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the WARNING mem AN To prevent electric shock and risk of fire hazards use a power source that is within specification only CAUTION Do NOT expose this appliance to rain or moisture REGULATORY NOTICE This equipment may generate or use radio frequency energy Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual The user could lose the authority to operate this equipment if an unauthorized change or modification is made REGULATORY INFORMATION FCC Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harm
7. CTION 3 Configuration Setup Use the on screen display OSD menus to configure your camera for the environment where it is installed and recording requirements you prefer 3 1 Menu operation Navigation through the configuration menus OSD is performed with the joystick located on the camera back panel The joystick will rock up down left and right and is pressed in to the camera to select an item Joystick Rock Up A Moves the cursor upwards in the menu Use this button to select an item or adjust the parameters Rock Down W Moves the cursor downwards in the menu Use this button to select an item or adjust the parameters Rock Right gt Moves the cursor to the right in the menu Use this button to select or adjust the parameters of the selected item The parameter changes each time this button is pressed Rock Left lt d Moves the cursor to the left in the menu Use this button to select or adjust the parameters of the selected item The parameter changes each time this button is pressed Press Down Select Opens the OSD menu system and executes selections and displays a submenu for an item with the mark Press the Set button to open the OSD main MENU consists of a list of sub menus or displays the option selected for a camera function When sub menus are available the symbol is MODEL EXPOSURE shown WHITE BAL IMAGE INTELLIGENCE SPECIAL FUNC DISPLAY EXIT 2 Megapixel Full HD C Mount Box
8. IONS WARNING Do not install this equipment in a confined space such as a bookcase or similar unit WARNING Wiring methods shall be in accordance with the National Electric Code ANSI NFPA 70 WARNING This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WARNING To reduce a risk of fire or electric shock do not expose this product to rain or moisture CAUTION Installation should be performed by a qualified service person and should conform to all local codes CAUTION To avoid electrical shock do not open the camera enclosure Refer servicing to qualified personnel only CAUTION This camera should not be exposed to water dripping or splashing and no objects filled with liquids such as vases should be placed on it CAUTION Danger of explosion if battery is incorrectly replaced Replaced only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions A suitable conduit entries knock outs or glands shall be provided in the cable entries of this product in the end use Holes in metal through which insulated wires pass shall have smooth well rounded surfaces or shall be provided with bushings DISPOSAL OF YOUR OLD APPLIANCES 1 All electrical and electronic products should be disposed of separately from the municipal waste stream via designat
9. P SEL SET TITLE RETURN MODEL EXPOSURE WHITE BAL IMAGE INTELLIGENCE SPECIAL FUNC DISPLAY EXIT DISP SEL Select display item D OFF ON TITLE OFF ON EZOOM OFF ON SET TITLE Select camera title menu Text edit ABCDEFGHIJKLMNOPQRST UVWXYZabcdefghijklmn opqrstuvwxyz t1 1l1 0123456789 4 7 SP BS CLR POS RETURN Set Title character set on screen 2 Megapixel Full HD C Mount Box Camera User Manual DISPLAY 13 SECTION 4 SPECIFICATIONS SECTION 4 Specifications Table 1 Component Specifications Component Value Image Sensor 1 3 Panasonic CMOS Total Pixels 2010 h x 1108 v 2 227 080 pixels Active Pixels 1944 h x 1092 v 2 122 848 pixels Scanning system Progressive Digital 1920 x 1080 1080p 30 fps 1280 x 720 720p 60fps elution Analog 700 TVL Visita Color 1 0 lux B W 0 5 lux Color DSS 0 002 lux BW DSS 0 001 lux wideout n NTSC PAL without WOR S N ratio gt 50 dB AGC off Function MODEL D amp N COLOR IR SMART IR CDS EXPOSURE BRIGHTNESS 0 20 steps LENS DC Manual SHUT SPEED Auto Manual 1 30 1 25 1 60000 DSS Off x2 x3 x4 AGC Off On WDR BLC Off WDR BLC DAYSNIGHT Auto Day Night Ext SMART IR N A WHITE BAL Auto Preset Manual Indoor Outdoor IMAGE SHARPNESS 0 10 steps MIRROR Off H V H amp V FREE
10. RMAT PG CVBS COMM DEFAULT RETURN SPECIAL FUNC DISPLAY EXIT SHADING DET Sets the shading calibration that the lens will perform Only occurs when the entire screen is viewed in white light OFF ON SHADING Select Lens shading compensation OFF ON DEFECT DET Compensates for bad pixels that my occur Occurs when the whole screen is in full black or if there is bad pixelation and it changes the THRS values until the screen is fixed OFF ON DEFOG Carry out defog function OFF ON LEVEL adjust amount of fog on display screen 0 10 NOTE When DEFOG is On ACE and WDR BLC function can not turn on SYSTEM Select NTSC or PAL NTSC PAL HD FORMAT Select Digital output 1080P or 720P 1080P 720P PG Select Color pattern generator OFF ON CVBS Select Composite signal OFF ON COMM Set up the camera ID baud rate protocol D Selectthe camera ID 1 255 BAUD RATE Select serial communication speed 2400 4800 9600 19200 38400 57600 115200 bps PROTOCOL Select operating protocol PELCO D PELCO P UPDATE DEFAULT All the settings will be restored to the factory default PG Pattern Generator PRIVACY MASK MOTION AREA cannot work simultaneously PG has priority second is PRIVACY MASK and lastly MOTION AREA For example if PG ON is selected while PRIVACY MASK is active PRIVACY MASK stops and PG is active SECTION 3 CONFIGURATION SETUP 3 8 DISPLAY MENU DIS
11. ZE Off On F 00M X137 HLC Off On ACE Off On 14 SECTION 4 SPECIFICATIONS Component Value DNR Off Low Middle High Auto D COMPRESS OFF ON INTELLIGENCE PRIVACY Off On 32 points MOTION Off On 4 points SPECIAL FUNC SHADING DET Off On SHADING Off On DEFECT DET Off On DEFOG Off On SYSTEM NTSC PAL HD FORMAT 1080p 720p PG Off On CVBS Off On COMM ID 1 255 Baud rate 2400 4800 9600 19200 38400 57600 115200 protocol PELCO P PELCO D UPDATE DEFAULT ON DONE Language English OSD Text 0 9 A Z a z Electrical Power Source 12 Vdc 10 Current 250 mA 12 Vdc 10 96 General Power Input DC JACK Video Output HD SDI BNC connector Operating Temperature 14 F 122 F 10 C 50 C Humidity 0 RH 80 90 RH Storage Temperature 4 F 140 F 20 C 60 C Humidity 0 96 RH 90 RH 2 Megapixel Full HD C Mount Box Camera User Manual 15 APPENDIX A TROUBLESHOOTING APPENDIX A Troubleshooting If you experience problems you cannot resolve please contact your distributor Problem Solution Nothing appears on the screen Check the power connections Check the video cable connections Ensure that the lens mode is set to DC VIDEO when using a VIDEO DC lens The video image is not clear lean the lens wi
12. and underside of the camera housing Flange back back focus set screw Used to lock the flange back The adjustment is required only when a lens without focus adjusting mechanism is mounted or when a lens with adjusting mechanism is mounted and more accurate focus that is needed Lens iris output connector 4 pin connector used to send the Iris control signal and power supply to an auto iris type lens NOTE Use only direct drive or DC drive lenses with this connector Pin DC type lenses Damping Damping Drive Drive 1 1 1 Camera back panel FULL HD 1080P Joystick OSD controls HD SDI video out terminal Power LED BLK HDC10 back connectors NOTES HD SDI video out terminal BNC terminal for HD SDI video signal output HDMI out connector Main cable terminal Joystick OSD controls Used to navigate the OSD menus See 3 1 Menu operation on page 7 for more information SECTION 1 INTRODUCTION HDMI out connector HDMI terminal for HD SDI video signal output Main cable terminal 6 pin main cable connector See below Power connector D C video output RS 485 leads Power connector 12 Vdc center video output analog video output or CVideo RS 485 leads Signal port for RS 485 communication yellow green Power LED LED lights when the power is applied to the camera 1 2 What you need To install the camera you will n
13. ed collection facilities appointed by the government or local authorities 2 The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health 3 For more detailed information about disposal of your old appliance please contact your city office waste disposal service or the shop where you purchased the product To disconnect power from the mains pull out the mains cord plug When install the product ensure that the plug is easily accessible 2 Megapixel Full HD C Mount Box Camera User Manual iii IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions All these safety and operating instructions should be read before the product is operated 2 Keep these instructions The safety operating and user instructions should be retained for future reference 3 Heed all warnings All warnings on the product and in the operating instructions should be adhered to 4 Follow all instructions All operating and user instructions should be followed 5 Donot use this apparatus near water For example near a bath tub wash bowl kitchen sink laundry tub in a wet basement near a swimming pool etc 6 Clean only with dry cloth Unplug this product from the wall outlet before cleaning Do not use liquid cleaners 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions Slots and openings
14. eed C or CS type lens 12 Vdc 1 A power source Mounting bracket Tools for mounting the camera 2 Megapixel Full HD C Mount Box Camera User Manual 3 SECTION 2 INSTALLATION SECTION 2 Installation 2 1 Install the camera mounting bracket The camera can be attached to a mounting bracket on the upper side or the underside of the camera Always follow the manufacture s guidelines when installing the mounting bracket 2 2 Attach the lens The camera will accommodate a DC drive or direct drive amp or CS type lens To attach the lens do the following 1 Remove the lens mounting cap from the lens mounting ring 2 Lens mounting ring SECTION 2 INSTALLATION 3 If you installed an auto iris lens verify that the cable pin definitions match the lens output iris connector see 1 1 Camera components on page 1 then plug the cable into the lens iris output connector Lens iris output connector 4 Follow the manufacturer s instructions to attach the camera mounting bracket to the mounting surface 5 Attach the camera to camera mounting bracket 6 Attach the main cable to the main cable terminal on the back of the camera 7 Ifyou are controlling the camera through an RS 485 network connect the main cable yellow RS 4854 and green R5 485 leads to your network See 1 1 1 Camera back panel on page 2 for more information 8 Connect the Cvideo output connector to a local setup monitor optional
15. ful interference in which case the user will be required to correct the interference at his own expense LEGAL NOTICE Observint Technologies Observint products are designed to meet safety and performance standards with the use of specific Observint authorized accessories Observint disclaims liability associated with the use of non Observint authorized accessories The recording transmission or broadcast of any person s voice without their consent or a court order is strictly prohibited by law Observint makes no representations concerning the legality of certain product applications such as the making transmission or recording of video and or audio signals of others without their knowledge and or consent We encourage you to check and comply with all applicable local state and federal laws and regulations before engaging in any form of surveillance or any transmission of radio frequencies Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Observint disclaims any proprietary interest in trademarks and trade names other than its own No part of this document may be reproduced or distributed in any form or by any means without the express written permission of Observint 2012 by Observint Inc All Rights Reserved 11000 N Mopac Expressway Building 300 Austin TX 78759 For Sales and Support please contact your distributor pT PRECAUT
16. in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer s instructions have been adhered to 8 Donotinstall near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long pe
17. riods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped TABLE OF CONTENTS Table of Contents PRECAUTIONS cC rM iii DISPOSAL OF YOUR OLD APPLIANCES oce etr ttr EX EVER E PREATEE SA EF RR ERU EE E EAS ii IMPORTANT SAFETY INSTRUCTIONS spoke iR at MERE SC POTIS iv SECTION 1 R TT OCC HON EELT TITT LITTLE E E E HER ERA eee 1 tl Camera UU ssc end Sees ce TT 1 2 VIS LU PRETI Tm 3 SECTION 2 illu 3555 was ere ba T o as 4 2 1 Install the camera mounting bracket sssesesresesesrrrrrrrrrrrerrrr ere rer ers rr rr rr rss 4 22 ara setasvordssaratvesesbewedo PE ded anes 4 SECTION 3 Configuration SEND mM 7 SUN SEU DRE TU EA oboe h rr i Te RR RES 7 BD WOVE ren tin suena Bing Nu sed pr NNV DR et cutee eer P ER 8 SUL db der bon ke a a A sr 8 ambe 9 2 2 SMA E E Ga ja ag aan 10 SN iic c c c A sirener Bel rn DANN 11 IT SPECIAL FUNCTION MPR O 12 25 2 uo cT ur h n ha Brin E oe RN ee a os ewe oan oes 13 SECTION 4 SD ooo eod 1 ed EFIE ERREUR oodd RENARE NAS TAN 14 APPENDIX A IFOMDICSNOOUNG RR R
18. termines content of the DAY amp NIGHT submenu D amp N Model AUTO DAY NIGHT EXT Delay 0 255 second BURST OFF ON THRS LOW MIDDLE HIGH Select Day amp Night change level Higher level make the night mode changed in lower illumination GAP LOW MIDDLE HIGH Select Day to Night mode change and Night to Day mode change SECTION 3 CONFIGURATION SETUP COLOR Model AUTO DAY NIGHT EXT Delay 0 255 second BURST OFF ON THRS LOW MIDDLE HIGH GAP LOW MIDDLE HIGH IR SMART Model not used with this camera IR CDS Model not used with this camera SMART IR OFF ON NOTE SMART IR function only works with IR Smart Model THRS Set up Smart IR turns on point When you level up the value Smart IR turns on in a low light condition AREA Setup areas to control Smart IR function When BLC mode is on Smart IR area is following BLC area POS X Adjust the window X Axis position P0S Y Adjust the window Y Axis position S X Adjust the window X Axis size S Y Adjust the window Y Axis size IR COMP Compensate when IR hunting happens When you use this function you should put a test object around 30 cm form the camera If an object is located in nearer than 30 cm from the camera and an object what could reflect the light is in front of the camera the camera cannot compensate a trouble of hunting 3 4 WHITE BALANCE MENU WHITE
19. th a soft clean cloth Adjust the monitor screen for room lighting conditions Move the camera if necessary The screen is dark Adjust the contrast feature of the monitor If you have an intermediate device set the 750 Hi Z properly and check the terminals If an auto iris lens is being used adjust the brightness level The MOTION DETECTION function is not working Is MOTION DETECTION mode turned on Is the MD Sensitivity set too low Increase the sensitivity Check the setting of the MD AREA The WDR function is not working Is the WDR level too low Is the AE Mode set to MANUAL WDR is disabled in MANUAL exposure mode Colors are not quite right Is the camera facing directly into sunlight or fluorescent light Is an auto iris lens being used Adjust if necessary Check the connection of the lens connector cable The Day amp Night function doesn t work Is the AGC EXPOSURE menu set to OFF The Auto Day amp Night Function doesn t work if the AGC is OFF Check the D lt gt N level 16 APPENDIX B CAMERA DIMENSIONS APPENDIX B Camera Dimensions 2 60 1 97 Side Front 2 Megapixel Full HD C Mount Box Camera User Manual 17
Download Pdf Manuals
Related Search