Home

Statement: Symbol description: More information: Version

1. The BIOS is the communication bridge between hardware and software correctly setting up the BIOS parameters is critical to maintain optimal system performance Power on the computer when the following message briefly appears at the bottom of the screen during the POST Power On Self Test press lt Del gt key to enter the Award BIOS CMOS Setup Utility Press TAB to show POST Screen DEL to enter SETUP Note We do not suggest that you change the default parameters in the BIOS Setup and we shall not be responsible for any damage that result from any changes that you make Main Menu The main menu allows you to select from the list of setup functions and two exit choices Use the arrow keys to select among the items and press lt Enter gt to accept or go to the sub menu Main Menu The items in the BIOS Setup main menu are explained below Standard CMOS Features The basic system configuration can be set up through this menu BIOS Features The general system features can be set up through this menu 755 760A01 Series User Manual 755A01 032604 p65 33 2004 3 26 15 28 Chapter 3 BIOS Description Advanced BIOS Features The advanced system features can be set up through this menu Advanced Chipset Features The values for the chipset can be changed through this menu and the sys tem performance can be optimized Integrated Peripherals All onboard peripherals can be set up through this menu Power Manageme
2. CPU_FAN FAN1 FAN2 There are three fan headers on this motherboard These fans will be automati cally turned off after the system enters suspend mode 4 i Se a a SENSE 12V GND eur MLL Lk 1 FAN1 j Y m z PE ee ee 7 sF aj Ch 1 ie i SENSE 12V GND 2 i Lr pe 1 CPU_FAN 1 o GND 12v FAN2 Audio Connectors MODEM_IN CD_IN AUX_IN To receive audio input from the CD ROM attach its audio connector to the CD_IN AUX_IN audio headers on the motherboard The Modem _IN connector allows the onboard audio to interface with a voice modem card with a similar connector It allows connecting the mono_in such as a phone or mono_out Such as a speaker between the onboard audio and the voice modem card PHONE_IN from Modem K GND MODEMIN Ja T me MONO_OUT to Modem EELE LEL z L A Fi PE E gi CD_L E E m ie m y Er 8 K fo im enD CD_IN ra jai ae i a ee ow od AUX_R _ GND AUX_IN S AUX L CD_R 755 760A01 Series User Manual 755A01 032604 p65 22 2004 3 26 15 28 h Fcon Chapter 2 Installation Instructions 1394 Header F_1394 optional The 1394 expansion cable can be connected to either the front provided that the front panel of your chassis is equipped with the appropriate interface or real panel of the chassis i p chee 2 TPA Teo MeL F E j i i a 12V Fused GND Wa
3. Write Protect as Enabled in CMOS Setup In this way the BIOS can not be overwritten but the DMI information can be updated Note FWH_EN default is enabled D 755 760A01 Series User Manual 755A01 032604 p65 86 2004 3 26 15 28 YFoxcom Chapter 6 Special BIOS Functions SuperSpeed 7 SuperSpeed is a powerful and efficient Easy Technology for PC DIY fans It offers a friendly interface The users can also realize in the BIOS setup the CPU core voltage adjustability Procedures 1 Correctly install your CPU Plug in other configurations and restore the system Switch on power to the system and press the lt Del gt key to enter BIOS Setup Enter the lt BIOS Features gt menu to set up the CPU clock Save and exit BIOS Setup your system will now boot successfully ao Poh BIOS provides you a set of basic values for your processor selection instead of the jumper settings The processor speed can be manually set from the lt BIOS Features gt menu screen Warning Be sure your selection is right CPU overclock can be dangerous we will not be responsible for any damage caused 755 760A01 Series User Manual 755A01 032604 p65 87 2004 3 26 15 28 hfaa magg Chapter 6 Special BIOS Functions FOXCONN SuperRecovery 2 0 SuperRecovery is an easy to operate tool for backing up or recovering your hard disk data It offers simplified user interfaces with hotkey access and allows you to experience unpr
4. function the start up password function must be canceled Also the PC power source must not be turned off The setting values are Disabled and Enabled Month Alarm This option is used to set the timing for the start up month The setting values contain 1 12 and NA 755 760A01 Series User Manual 755A01 032604 p65 52 2004 3 26 15 28 4Foxcom Chapter 3 BIOS Description lt Day of Month Alarm This option is used to set the timing for the start up day of the month The setting values contain 0 31 Time hh mm ss Alarm This option is used to set the timing for the start up time The setting values contain hh 0 23 mm 0 59 ss 0 59 Primary Secondary IDE Default Disabled When these items are enabled the system will restart the power saving timeout counters when any activity is detected on any of the drives or devices on the primary or secondary IDE channels The setting values are Disabled and Enabled FDD COM LPT Port Default Disabled When this option is enabled the system will restart the power saving timeout counters when any activity is detected on the floppy disk drive serial ports or the parallel port PCI PIRQ A D Default Disabled When this option is disabled any PCI devices set as the master will not power on the system 755 760A01 Series User Manual 63 755A01 032604 p65 53 2004 3 26 15 28 h F conmn Chapter 3 BIOS Description PnP PCI Configurations PnP PCI Con
5. 2000 ME XP soft off e Supports Wake up On LAN Wake up on Modem functions e Supports PC Health function capable of monitoring system voltage CPU system temperature and fan speed 755 760A01 Series User Manual 755A01 032604 p65 3 2004 3 26 15 28 h Facon Chapter 1 Product Introduction Motherboard Layout 755 760A01 Series User Manual 755A01 032604 p65 4 2004 3 26 15 28 F Chapter 1 Product Introduction HFOXCONN ATX 12V connector This power connector connects the 4 pin 12V plug from the ATX 12V power supply AGP slot This Accelerated Graphics Port AGP slot supports 1 5V AGP8X mode graphics cards for 3D graphical applications amp CPU socket A 754 pin surface mount Zero Insertion Force ZIF Socket for the AMD Athlon64 Processor Support HyperThansport Technology with 8 16 links up to 1600MT s bandwidth North Bridge controller The SiS 755 760 integrate a high performance host interface for the AMD Athlon64 Processor and SiS MuTIOL technology DDR DIMM sockets These three 184 pin DIMM sockets support up to 3GB system memory using unbuffered non ECC PC3200 2700 2100 DDR DIMMS ATX power connector This 20 pin connector connects to an ATX power supply The power supply must have at least 1A on the 5V standby lead 5VSB Super I O controller The ITE8705F controller Super I O provides support that includes floppy serial ports and parallel port to rest of platform
6. 714 738 8838 Equipment Classification FCC Class B Subassembly Type of Product Motherboard Manufacturer HON HAI PRECISION INDUSTRY COMPANY LTD Address 66 CHUNG SHAN RD TU CHENG INDUSTRIAL DISTRICT TAIPEI HSIEN TAIWAN R O C Supplementary Information This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Tested to comply with FCC standards Signature 4 eos t pon 5 Date 2004 755A01 English preface 031504 p65 4 2004 3 26 16 06 Table of Contents Chapter a gt Product Introduction Maim FS ASS seirce e a A EO AATE ARR 2 Motherboard Layout grctorncase ctecereicecjnansne cee auetiedaausanarntsanmsiendeiyewedigetiaenencasigeneht 4 Chapter 2 Installation Instructions E r E P E E TEE PEE S E EN E E A E E EE T E E 9 MIETO een E N E E A E S 12 Power Supply sinceteosacisaansinnnnsontuieiwesaudcnduatiadsaneiniddinnwtoavidensuboevianddanpanidomiongtns 16 Rear Panel Connectors sacessicnnnvissasccadatssnestantviwanctvnassvesustetbovasenecsteawasaneaceess 17 Other CONNEC OIS saisine a aE i r ENERE aN 19 Expansion O ls cs E e aE EREE E 26 SUTTONS aac caeetecananesscacc cnecaaseeattesececcnaeeeeeendanseaceececeseaccre anceesessntnsesdeneee cece 28 Chapter E BIOS Description Enter BIOS Set siicsiictascncianhea
7. CAS delay lt tRCD gt Default Auto The available setting values are Auto 2 7 Bus Clocks 755 760A01 Series User Manual 755A01 032604 p65 43 2004 3 26 15 28 R HFoaozconn Chapter 3 BIOS Description Row to Row delay lt tRRD gt Default Auto The available setting values are Auto 2 7 Bus Clocks Min RAS active time lt tRAS gt Default Auto The available setting values are Auto 5 15 Bus Clocks Row precharge Time lt tRP gt Default Auto The available setting values are Auto 2 6 Bus Clocks Write recovery time lt tWR gt Default Auto The available setting values are Auto 2 3 Bus Clocks Write to Read delay lt tWTR gt Default Auto The available setting values are Auto 1 Bus Clock Read to Write delay lt tRWT gt Default Auto The available setting values are Auto 1 6 Bus Clocks Refresh period lt tREF gt Default Auto The available setting values are Auto 1x1552 Cycles 4x4672 Cycles 755 760A01 Series User Manual 755A01 032604 p65 44 2004 3 26 15 28 R HFaozconn Chapter 3 BIOS Description Integrated Peripherals Integrated Peripherals Menu SIS OnChip IDE Device Press enter to set onchip IDE device Please refer to page 46 SIS OnChip PCI Device Press enter to set onchip PCI device Please refer to page 47 lt Onboard SuperlO Device Press enter to set onchip onboard SuperlO device Please refer to page 48 IDE HDD Block Mode Default En
8. Manual 755A01 032604 p65 71 2004 3 26 15 28 Facon Chapter 4 Driver CD Introduction Install Adobe Reader From the main menu select lt Accessories gt as shown in following fig 1 Click lt Adobe Reader gt to start the setup Install Norton Internet Security 2004 From the main menu select lt Accessories gt as shown in following fig 1 Click lt Norton Internet Security 2004 gt to start the setup FOMOOMY LILI Pty Co a Note ra i If your system is Windows 98 or Windows ME please make sure that your Internet Explorer version is 5 01 with service pack 2 or higher 755 760A01 Series User Manual 755A01 032604 p65 72 2004 3 26 15 28 755A01 032604 p65 This chapter will introduce how to use attached software This chapter includes the following information SuperStep SuperUpdate SuperLogo 73 2004 3 26 15 28 Chapter 5 Directions for Bundled Software iW FOXcCorn SuperStep Gre SupersStep is a utility that allows users to change the frequency of the CPU It also displays system health introduction including CPU temperature CPU voltage and PCI AGP clock SuperStep features 1 Supports Win98SE WinME Win2000 and WinXP 2 Automatic alarm mechanism when system runs irregularly 3 Adjusts the CPU frequency to speed up your system and achieve better system performance 4 Simple and easy to operate with a user friendly graphics interface Using SuperSte
9. Memory This motherboard includes three 184 pin slots with 266 333 400 MHz Single Channel DDR DRAM interface You must install at least one memory module to ensure normal operation If you install three modules they must be the same speed Mixing memory modules from different manufactures are not recommended E To eo Me a F b 4 m HH Baca eit i ry ae a 0 Urn aie 4 a ig nna o i a mE a a a ay E 1 F h T p a n TEINEGI F j bi S a Mapes it ee a ie 3 755 760A01 Series User Manual 755A01 032604 p65 12 2004 3 26 15 28 Recommended Memory Configurations Chapter 2 Installation Instructions The following table lists the recommended memory configurations U Www wow Ww Ww OIN N N N NYO NB NYO NB NY NM N WN Socket 1 x8 single rank or x16 empty empty x8 double rank empty empty x8 single rank or x16 x8 single rank or x16 x8 single rank or x16 x8 single rank or x16 x8 double rank x8 double rank x8 double rank x8 double rank empty empty empty empty x8 single rank or x16 x8 single rank or x16 x8 single rank or x16 x8 single rank or x16 x8 double rank x8 double rank x8 double rank x8 double rank CA2 Socket 2 empty x8 single rank or x16 empty empty x8 double rank empty x8 single rank or x16 x8 double rank empty empty x8 single rank or x16 x8 double rank
10. aise cio cise dosrncicnerns E E E SAEST RRE 58 755A01 English preface 031504 p65 5 2004 3 26 16 06 Table of Contents Chapter O Driver CD Introduction LAU CD GOM EN conctatacareseiecceasonesguretoneuitreabyncloaiecbasinacencssveiatentonymienalaucugions Start to install drivers wc sccsesivea dnacusebonnncdancannteeenndvendvsecuvenns dtsieduraedaadvangasavbewubaes Install IDE Driver ccccsadunssissindsineuessinsenesendeacnasunesnencascineudeheceuslessndsususdenasiesauieacns Install SiS RAID optional siaucsescnsanceuncersvacen dows uncemenieexadesaesshsawsnivemeeaneenceterads Install AGP Driver ccccecccceecceececeeeeeeeeeeeeeeeeeeeueeeeceeeeeeeeeeeeeegeesueenneetanees Install DirectX 9 0b cesisecesictindscacactueancamcntanmentiniaadecsanediaecsitvensiiscsiaebinyacseeebiuce Install USB 2 0 Driver vinccsiasiincencrontacendnaveatecaiendandadneoriwadsiidcabivancaaiicaaneyieasiens Using 4 6 Channel Audio sesisssccrcisccecacnneisanenstinedesacnancsadenencentcreaststvectapaai Install LAN Driver c cccceceeeceeceeeeeeeceeseeeeeeeeeeeeeeeeeeteeeeeeeeeteeeneeeegeegeees Install Sil3112 SATA RAID Driver ccc cece eecceeeeeeeeeeeeeeeeseeeeeeeeeeeeeeeeeeeaness PRS Fe SIS CNY sssrin antes usrenavesestansts AEREE AEREN Install Adobe Reader ccc cecccecceeeceeeceeeeeeeeeececeeeeeeeeeeeseeeteeeteeeeeeeeeseeetaess Install Norton Internet Security 2004 0 0 cecceccecessseeeeeeeseeeeeeesesenseeeeeesanees Chapter O Direction
11. by BIOS read only month month from Jan to Dec date date from 1 to 31 can be changed by using the keyboard year year set up by users Time This option allows you to set up the desired time usually as the current time with lt hour gt lt minute gt lt second gt format IDE Channel 0 1 Master Slave amp Channel 2 3 Master These categories identify the HDD types of 4 IDE channels installed in the computer system There are three choices provided for the Enhanced IDE BIOS None Auto and Manual None means no HDD is installed or set Auto means the system can auto detect the hard disk when booting up by choosing Manual and changing Access Mode to CHS the related information should be entered manually Enter the information directly from the keyboard and press lt Enter gt Cylinder number of cylinders number of heads Precomp write pre compensation Landing Zone Landing Zone Sector number of sectors BS 755 760A01 Series User Manual 755A01 032604 p65 35 2004 3 26 15 28 4Foxcorm Chapter 3 BIOS Description Award Phoenix BIOS can support 4 HDD modes CHS LBA and Large or Auto mode CHS For HDD lt 528MB LBA For HDD gt 528MB amp supporting LBA Logical Block Addressing Large For HDD gt 528MB but not supporting LBA Auto Recommended mode Drive A B This option allows you to select the kind of FDD to be installed including None 860K 5 25in 1 2M 5 25in 720K 3 5i
12. through the SiS 755 760 and SiS 964 via the Low Pin Count LPC interface Floppy disk connector This connector accommodates the provided ribbon cable for the floppy disk drive One side of the connector is slotted to prevent incorrect insertion of the floppy disk cable 755 760A01 Series User Manual 755A01 032604 p65 5 2004 3 26 15 28 h F connn Chapter 1 Product Introduction IDE connectors These dual Channel bus master IDE connectors support Ultra DMA 133 100 66 Both the primary blue and secondary white connectors are slotted to prevent incorrect insertion of the IDE ribbon cable Flash ROM This 4Mb firmware contains the programmable BIOS program South Bridge controller Referred to as the SiS 964 MuTIOL Media I O this controller integrates the audio controller with AC 97 interface Ethernet MAC Universal Serial Bus Host controller S ATA interface IDE Master Slave controllers and the MuTIOL connect to PCI bridge PCI Slots These five 32 bit PCI 2 2 expansion slots support bus master PCI cards like SCSI or LAN cards with 133MB s maximum throughput Audio CODEC The ALC655 is an AC 97 CODEC that allows 6 Channel audio playback The audio CODEC provides six DAC channel for 5 1 surround sound S PDIF output and Line in stereo inputs integrated headphone amplifier greater than 90dB dynamic range with the jack sense and jack enumeration feature 1394 controller optional V1T6307 is th
13. wake up from S1 and S3 mode e Supports USB 2 0 protocol up to 480Mbps transmission rate SERIAL Onboard Serial ATA ATA e 150MBps transfer rate e Supports four S ATA devices such as HDD etc e Supports RaidO Raid1 and JBOD Onboard 1394 optional FH IEEE 354 e Supports hot plug e With rate of transmission at 400Mbps e Self configured addressing Supports two independent 1394 units synchronously at most such as HDD CD ROM 755 760A01 Series User Manual 755A01 032604 p65 2 2004 3 26 15 28 A FoOxcorm Chapter 1 Product Introduction Onboard LAN optional e Supports10 100 1000 optional Mbps Ethernet e LAN interface built in on board a Onboard Audio a e AC 97 2 3 Specification Compliant e Supports S PDIF output e Onboard Line in jack Microphone in jack Line out jack e Supports 5 1 channels audio setting via software BIOS e Licensed advanced AWARD Phoenix BIOS supports flash ROM Plug and Play e Supports IDE CD ROM SCSI HDD or USB device boot up Green Function e Supports ACPI Advanced Configuration and Power Interface e Supports SO normal S1 power on suspend S3 Suspend to RAM S4 Suspend to disk depends on OS and S5 soft off Expansion Slots e 5 PCI slots e 1 AGP slot Onboard Graphics only for 760A01 e Supports integrated VGA display function AGP 8X support GP e Supports AGP 8X graphics cards Advanced Features e PCI 2 2 Specification Compliant e Supports Windows98
14. 0 PC3200 DDR 400 PC2700 DDR 333 PC3200 DDR 400 PC3200 DDR 400 PC3200 DDR 400 256M 512M 256M 256M 512M 256M 512M 256M 256M 512M 512M 256M 256M 256M 512M 512M 256M 512M 256M 1G 755 760A01 Series User Manual 2004 3 26 15 28 R h Foxconn Chapter 2 Installation Instructions Installation of DDR Memory 1 There is only one gap in the center of the DIMM slot and the memory module can be fixed in one direction only 2 Align the memory module to the DIMM slot and insert the module vertically into the DIMM slot 104 Pins 80 Pins 3 The plastic clips at both sides of the DIMM slot will lock automatically Note Be sure to unplug the AC power supply before adding or re moving expansion cards or other system peripherals espe cially the memory devices otherwise your motherboard or the system memory might be seriously damaged 755 760A01 Series User Manual 755A01 032604 p65 15 2004 3 26 15 28 h Facon Chapter 2 Installation Instructions Power Supply This motherboard uses an ATX power supply In order to avoid damaging any devices make sure that they have been installed properly prior to connecting the power supply ATX 12V Power Connector PWR2 The 4 pin ATX 12V power supply connects to PWR2 and provides power to the CPU ATX Power Connector PWR1 PWR1 is the ATX power supply connector Make sure that the power supp
15. 01 Series User Manual 755A01 032604 p65 47 2004 3 26 15 28 R HFoaozcon Chapter 3 BIOS Description lt Onboard Lan Boot ROM Default Disabled This option is used to decide whether to invoke the boot ROM of the onboard LAN chip The available setting values are Disabled and Enabled Dee Onboard SuperlO Device Menu lt Onboard FDC Controller Default Enabled This option is used to set whether the onboard FDC controller is enabled The available setting values are Disabled and Enabled lt Onboard Serial Port 1 2 Default 3F8 IRQ4 2F8 IRQ3 This option is used to assign the I O address and interrupt request IRQ for the onboard serial port 1 2 Note Do not try to set the same values for serial port 1 and 2 lt UART Mode Select Default Normal Use this option to select the UART mode Setting values include Normal IrDA ASKIR and SCR The setting value is determined by the infrared mod ule installed on the board UR2 Duplex Mode Default Half This option is available when UART 2 mode is set to either ASKIR or IRDA This option enables you to determine the infared function of the onboard infrared chip The available setting values are Half and Full Onboard Parallel Port Default 378 IRQ7 This option allows you to determine onboard parallel port controller I O ad dress and interrupt request IRQ Setting values include Disabled 378 IR Q7 278 IRQ5 and 3BC IRQ7 755 760A01 Series User Manu
16. 1 Silicon 3112A RAID Installation Support Disk x1 755A01 English preface 031504 p65 2 2004 3 26 16 06 Declaration of conformity HON HAI PRECISION INDUSTRY COMPANY LTD 66 CHUNG SHAN RD TU CHENG INDUSTRIAL DISTRICT TAIPEI HSIEN TAIWAN R O C declares that the product Motherboard 755 760A01 series is in conformity with reference to the specification under which conformity is declared in accordance with 89 336 EEC EMC Directive MV EN 55022 A1 2000 Limits and methods of measurements of radio disturbance characteristics of information technology equipment V EN 61000 3 2 A14 2000 Electromagnetic compatibility EMC Part 3 Limits Section 2 Limits for harmonic current emissions equipment input current lt 16A per phase V EN 61000 3 3 A1 2001 Electromagnetic compatibility EMC Part 3 Limits Section 2 Limits of voltage fluctuations and flicker in low voltage supply systems for equipment with rated current lt 16A V EN 55024 A1 2001 Information technology equipment Immunity characteristics limits and methods of measurement PEPPE fae Signature paag Lerat Place Date TAIPEI 2004 H a Printed Name James Liang Position Title Assistant President 755A01 English preface 031504 p65 3 2004 3 26 16 06 Declaration of conformity Trade Name Foxconn Model Name 755 760A01 Responsible Party PCE Industry Inc Address 458 E Lambert Rd Fullerton CA 92835 Telephone 714 738 8868 Facsimile
17. 4 for top right logo and 640 x 480 or 800 x 600 for full screen logo Using SuperLogo Go to ROM Info page Display the Flash Information E Sea baa eee hail i a Ree f Link to Foxconn website RIOS information Exit Program Minimize Window SuperLogo On Line Help About SuperLogo SuperlLloege 755 760A01 Series User Manual 755A01 032604 p65 82 2004 3 26 15 28 Foxconn Go to Change Logo page Full screen mode Top Right mode Boot without logo Superlogsea Go to Update BIOS page ene nate Tin file location Superloega Go to Backup page dfe Pos Teler Mayka pi ihj Fir Backup whole gems BIOS image Super L og 755 760A01 Series User Manual 755A01 032604 p65 83 Chapter 5 Directions for Bundled Software Follow the Wizard to complete the logo update Browse a BIN file for updating BIOS Follow the Wizard to complete the BIOS function Backup Logo Follow the Wizard to complete the backup functio 2004 3 26 15 28 755A01 032604 p65 This chapter will introduce new functions of BIOS and how to use them in detail It can further exert the max potential of motherboard to bring you super value enjoyment This chapter introduces the following new functions of BIOS SuperBoot SuperBlOS Protect SuperSpeed SuperRecovery 84 2004 3 26 15 28 JFoxcom Chapter 6 Special BIOS Functions i a F SuperBoot r SuperBoot technology gre
18. A device to the motherboard These connectors support the thin Serial ATA cables for primary internal storage devices The current S ATA interface allows up to 150MB s data transfer rate There are four S ATA connectors on the motherboard y p p s uN GND aoe ETTEI 1 Pa het EY k TX i Fa at GND ia RX E RX HS GND ar a a WE a a T ey S ATA1 S ATA2 l S ATA3 S ATA4 755 760A01 Series User Manual 755A01 032604 p65 24 2004 3 26 15 28 h Fcon Chapter 2 Installation Instructions Audio Interface F_AUDIO The audio port includes two parts the Front Audio and Rear Audio Their priority is sequenced from high to low Front Audio to Rear Audio If headphones are plugged into the front panel of the chassis using the Front Audio then the Line Out Rear Audio on the rear panel will not work If you do not want to use the Front Audio pin 5 and 6 pin 9 and 10 must be short and then the signal will be sent to the rear audio port MIC MIC_GND MIC_PWR 5VAC AUD_OUT_R AUT_RET_R NA EMPTY AUD_OUT_L AUT_RET_L F_AUDIO S PDIF Out Connector SPD OUT The S PDIF out connector is capable of providing digital audio to external speak ers or compressed AC3 data to an external Dolby digital decoder 4 ND SPDIF OUT EMPTY 5V SYS SPD_OUT 755 760A01 Series User Manual 755A01 032604 p65 25 2004 3 26 15 28 R Facon Chapter 2 Installation Instructions Speaker Connector The speaker connector i
19. ET SW Attach the connector to the Reset switch on the front panel of the case the system will restart when the switch is pressed Power LED Connector PWR LED Attach the connector to the power LED on the front panel of the case The Power LED indicates the power supply status When the system is in SO status the LED is on When the system is in S1 status the LED is blink When the system is in S3 S4 S5 staus the LED is off 755 760A01 Series User Manual 755A01 032604 p65 20 2004 3 26 15 28 755A01 032604 p65 21 Bracon Chapter 2 Installation Instructions IrDA Header IR The IrDA infrared transmission allows your computer to send and receive data via an infrared ray The relevant parameters for the BIOS Integrated Peripherals should be set prior to using this function i _ E amp Tee Me 5 E F Empty ge oO IRRX i a al aj i O GND i AE O E Li Pose ori ha USB Header F_USB 1 F_USB 2 Besides four USB ports on the rear panel the series of motherboards also have two 10 pin headers on board which may connect to front panel USB cable optional to provide additional four USB ports 1 2 Wee VCC D5 D4 ek het i D5 D4 Teor we ne sla i a gail Empty NC f i Piss 9 10 ye T G F_USB 1 i 1 2 VCC VCC D7 D6 D7 D6 GND GND Empty NC 9 10 F_USB 2 755 760A01 Series User Manual 2004 3 26 15 28 h Facon Chapter 2 Installation Instructions Fan Connectors
20. S Features Menu SuperBoot SuperBoot Default Disabled SuperBoot allows system relevant information to be stored in CMOS upon the first normal startup of your PC and the relevant parameters will be restored to help the system start up more quickly on each subsequent startup The available setting values are Disabled and Enabled SuperBIOS Protect SuperBIOS Protect Default Disabled Super BIOS Protect funtion protects your PC from being affected by viruses e g CIH The available setting values are Disabled and Enabled lt SuperSpeed CPU Clock Depending on the specification of the CPU The conventional over clock method uses the jumpers on the motherboard and it is both troublesome and apt to errors By using SuperSpeed a CPU can be overclocked by keying in the desired in the CPU clock range SuperRecovery SuperRecovery Hotkey Default LSHIFT F12 SuperRecovery provides the users with an excellent data protection and HDD recovery function There are 12 optional settings and the default setting is LSHIFT F12 Warning Be sure your selection is right CPU overclock will be dangerous We will not be responsible for any damage caused 755 760A01 Series User Manual 755A01 032604 p65 38 2004 3 26 15 28 h FOoxcomn Chapter 3 BIOS Description Advanced BIOS Features fein Detar IEI ak jE i kiia Tiii fiee ilee peale Plaji EILA Fl Sl Ei z1 i faji saa Mga 00 I a ipi misal Advanced BIOS Feature
21. Statement This manual is the intellectual property of Foxconn Inc Although the information in this manual may be changed or modified at any time Foxconn does not obligate itself to inform the user of these changes Trademark All trademarks are the property of their respective owners Version Users Manual V1 1 in English for 755 760A01 series motherboard P N 91 181 755 11 00 Symbol description Note refers to important information that can help you to use motherboard better Attention indicates that it may damage hardware or cause data loss and tells you how to avoid such problems Warning means that a potential risk of property damage or physical injury exists More information lf you want more information about our products please visit Foxconn s website www foxconnchannel com 755A01 English preface 031504 p65 1 2004 3 26 16 06 Item Checklist Thank for your purchasing Foxconn s 755 760A01 series motherboard Please check the package if there are missing or damaged items contact your distribu tor as soon as possible 755 760A01 series motherboard x1 Foxconn Utility CD x1 Users Manual x1 755 760A01 series Flyer x1 SATA RAID user s Manual x1 IDE Ribbon cable x1 FDD Ribbon cable x1 I O Shield x1 SPDIF Cable x1 optional lt USB 2 0 Cable x1 optional lt S ATA Signal Cable x2 S ATA Power Cable x1 SiS964 RAID Installation Support Disk x
22. Utility CD content This motherboard comes with one Utility CD To begin using the CD simply insert the CD into your CD ROM driver The CD will automatically display the main menu screen FOXCONN tility Cpe E 1 Install Driver Using this option to install all the drivers for your motherboard You should install the drivers sequentially from first to last A IDE Driver B SiS SATA RAID C AGP Driver D Direct X 9 0b E USB 2 0 Driver F Audio Driver G LAN Driver H Sil8112 SATA RAID 2 Accessories Use this option to install additional software programs A SuperUtility B Adobe Reader C Norton Internet Security 2004 3 Browse CD Click to browse this CD 4 Homepage Click here to visit Foxconn motherboard homepage Note 1 Install the latest patch first if your OS is Windows XP or Win dows 2000 2 Follow the CD screen order to install your motherboard drivers 755 760A01 Series User Manual 755A01 032604 p65 60 2004 3 26 15 28 Q JFaxconNN Chapter 4 Driver CD Introduction Start to Install divers Select lt Install Driver gt and click to enter the install driver screen You can select the driver that you want to install and begin the setup steps Note 1 a E The following setup steps are based on Windows XP environment There may be some differences with other operat _ Ing systems Install IDE Driver Click lt Install Driver gt from the main menu and enter the ins
23. abled This option is used to set whether the IDE HDD Block Mode is allowed The available setting values are Disabled and Enabled Init Display First Default PClI Slot This option is used to set which display device will be used first when your PC starts up The available setting values are PCI Slot and AGP lt USB0 1 2 2 0 Access Interface Default EDB Bus This option is used to set USBO 1 2 2 0 Access Interface The available setting values are PCI Bus and EDB Bus lt Audio Access Interface Default EDB Bus This option is used to set audio access Interface The available setting values are PCI Bus and EDB Bus 755 760A01 Series User Manual 755A01 032604 p65 45 2004 3 26 15 28 THFoOxcorT Chapter 3 BIOS Description SIS Onchip IDE Device Menu Internal PCI IDE Default Both This option is used to set the ports of onboard IDE The available setting values are Disabled Primary Secondary and Both IDE Primary Secondary Master Slave PIO Default Auto These four items let you assign which kind of PlIO Programmer Input Out put is used by IDE devices Choose Auto to let the system auto detect which PIO mode is the best or select a PIO mode from 0 4 Primary Secondary Master Slave UltraDMA Default Auto UltraDMA technology provides faster access to IDE devices If you install a device that supports UltraDMA change the appropriate items on this list to Auto The available setting values are Dis
24. abled and Auto IDE DMA transfer access Default Enabled This option is used to enable or disable IDE DMA transfer access IDE Burst Mode Default Enabled This option is used to enable or disable IDE burst mode 755 760A01 Series User Manual 755A01 032604 p65 46 2004 3 26 15 28 Chapter 3 BIOS Description SIS OnChip PCI Device Menu SIS USB Controller Default Enabled This option is used to enable or disable SIS USB controller USB 2 0 Supports Default Enabled This option is used to enable or disable USB 2 0 USB Keyboard Support Default Enabled This option is used to set USB keyboard support The available setting values are Disabled and Enabled USB Mouse Support Default Enabled This option is used to set USB mouse support The available setting values are Disabled and Enabled SIS AC97 AUDIO Default Enabled This option is used to enable or disable SIS AC97 audio SIS S W Modem Default Enabled This option is used to enable or disable CNR modem SIS Serial ATA Controller Default Enabled This option is used to enable or disable SIS serial ATA controller The available setting values are Disabled and Enabled SIS Serial ATA Mode Default IDE This option is used to set Serial ATA mode The default is recommended The available setting values are IDE and RAID Lan Controller Default Enabled The available setting values are Disabled and Enabled 755 760A
25. air al f HPF iiia feted a Pee divi 7 hn mercigie ta make cc HESE Ht aero ro A Mii sid r mijesi ER sya in On line help message Divide Hidden Partition 1 What s a Hidden Partition SuperRecovery can be used to divide a hidden partition which is to be reserved for backing up HDD data The operation of Division will erase all the old data saved in the HDD to make sure that the following operations can be continued Once the division is done any future variation to the HDD will never affect the area of hidden partition such as virus windows system breaking down and data loss SuperRecovery can recover all the data backed up in hidden partition The user can therefore easily get the computer on track again 2 Divide Hidden Partition 1 Enter a percentage of the HDD total capacity or an actual size in MB as the size of the hidden partition such as 30 or 3000 Press Enter to confirm your input As the average rate of compression is 50 or so you are suggested to divide 30 of the total as the capacity of the hidden partition 2 The system will then prompt you to Enter Y or N for confirmation Press Y to restart the computer and the division for hidden partition will be taken into effect after the system is restarted 755 760A01 Series User Manual 755A01 032604 p65 90 2004 3 26 15 28 h Facon Chapter 6 Special BIOS Functions Attention 1 All the data will be cleared a
26. al 755A01 032604 p65 48 2004 3 26 15 28 R hias magg Chapter 3 BIOS Description Parallel Port Mode Default SPP Select an address amd corresponding interrupt for the onboard parallel port Setting values include SPP EPP ECP ECP EPP ECP Mode Use DMA Default 3 Select a DMA channel for the parallel port when using the ECP mode This field is only configurable if Parallel Port Mode is set to ECP The available setting values are 3 and 1 755 760A01 Series User Manual 755A01 032604 p65 49 2004 3 26 15 28 h F conmn Chapter 3 BIOS Description Power Management ae Pearle leet ALPE Pelee F Ree Pei FLoteerrs Hr ip i LELLE Fk Pade FaF iin Le Fr TPL inim Me Power Management Setup Menu lt ACPI function Default Enabled ACPI stands for Advanced Configuration and Power Interface ACPI is a standard that defines power and configuration management interfaces be tween an operating system and the BIOS In other words it is a standard that describes how computer components work together to manage system hardware In order to use this function the ACPI specification must be sup ported by the OS for example Windows2000 or WindowsXP The available setting values are Enabled and Disabled lt ACPI Suspend Type Default S3 STR This option is used to set the energy saving mode of the ACPI function When you select S1 POS mode the power will not shut off and the supply status will re
27. ard FLOPPY interface supporting 360K 720K 1 2M 1 44M and 2 88M FDDs 1 i EGG An cia sa FLOPPY Connector HDD connectors PIDE amp SIDE These connectors support the provided UltraDMA133 100 66 IDE hard disk rib bon cable Connect the cable s blue connector to the primary recommended or secondary IDE connector then connect the gray connector to the Ultra DMA133 100 66 slave device hard disk drive and the black connector to the Ultra DMA133 100 66 master device If you install two hard disks you must configure the second drive as a slave device by setting its jumper accordingly Refer to the hard disk documentation for the jumper settings L3 Attention Ribbon cables are directional therefore make sure to always con nect with the cable on the same side as pin 1 of the PIDE SIDE or FLOPPY connector on the motherboard 755 760A01 Series User Manual 755A01 032604 p65 19 2004 3 26 15 28 Rh Focon Chapter 2 Installation Instructions Front Panel Connector FP1 This motherboard includes one connector for connecting the front panel switch and LED indicator 1 2 p e g rae g ed 1 9 i Hia di m mE HD LED PWR LED y m j i AE 8 Far H RESET SW WR SW z ag S Hr E Og Ne hE z E E E re a a AF p a FP1 Hard Disk LED Connector HD LED Attach the connector to the HD LED on the front panel of the case the LED will flash while the HDD is in operation Reset Switch RES
28. artitions 755 760A01 Series User Manual 755A01 032604 p65 92 2004 3 26 15 28 5 kh FoOXxcormM Chapter 6 Special BIOS Functions 3 Backup Harddisk Data 1 If there are active partitions System partition you can choose an active partition or the whole disk for backing up But only one can be taken between the two choices Old data will be replaced by the newly backed up 755 760A01 Series User Manual 755A01 032604 p65 93 2004 3 26 15 28 R Fazon Chapter 6 Special BIOS Functions 3 A report with all the critical data on this operation will be listed after backing up is completed Original Size The data size loaded in selected partition Valid Size The size of valid data Elapsed Time How long the process took to complete Compressed Size The size of data after compression Compressed Rate Compressed Size Valid Size 4 Back to Main This item is used to quit the Backup interface Recovery Select RECOVERY to enter the Recovery interface The following sub function are available as RECOVER CMOS SETUP RECOVER PARTITION TABLE and RECOVER HARDDISK DATA You can switch the highlight bar by pressing the arrow keys to make a selection and press Enter to confirm your selection 755 760A01 Series User Manual 755A01 032604 p65 94 2004 3 26 15 28 Foxconn Chapter 6 Special BIOS Functions 1 Recover CMOS Setup This function can help to restore the latest backup of CMOS se
29. atly reduces the long boot process time of computers A BIOS without SuperBoot has to perform many routines every time when the system starts such as checking the system core and initializing system peripherals Now with SuperBoot a PC can boot up without any unnecessary SuperBoot is quite easy to use choose the right option in CMOS setup refer to BIOS features SuperBoot saves the information when the PC boots up at the first time and restores the parameters for the system thus letting the PC boot freely and rapidly Notes 1 If the previous boot was not completed then the BIOS will perform normal POST even if SuperBoot is enabled 2 No matter SuperBoot is enabled or not the BIOS will perform normal POST if CMOS fails 755 760A01 Series User Manual 755A01 032604 p65 85 2004 3 26 15 28 R Fagron Chapter 6 Special BIOS Functions PORCO SuperBIOS Protect us The BIOS of the motherboard is contained inside the Flash ROM Severe vi ruses such as CIH virus are so dangerous that it may overwrite the BIOS of the motherboard If the BIOS has been damaged the system will be unable to boot We provide the following solution which protects the system BIOS from being attacked by such viruses There are two choices which implement this function 1 Set the jumper FWH_EN as disabled pin 1 2 closed the BIOS can not be overwritten 2 Set the jumper FWH_EN as enabled pin 2 3 closed meanwhile set Flash
30. ble for connecting USB 2 0 1 1 devices 755 760A01 Series User Manual D 755A01 032604 p65 17 2004 3 26 15 28 R Facon Chapter 2 Installation Instructions 1394 port optional This digital interface supports electronic devices such as digital cameras scanners and printers LAN Port This port allows connection to a Local Area Network LAN through a network hub Audio Port When using a two channel sound source the Line out jack is used to connect to speaker or headphone the Line in port connects to an external CD player tape player or other audio devices The MIC is used to connect to the microphone eo Line in Line out o B n When using a 6 channel sound source connect the front speaker to the green audio output connect the surround sound speaker to the blue audio input connect the central speaker sub woofer to the red MIC input as being shown in the following figure ACS Audis Coaligura tion gt me be T a F ct Ol j ii HF Hj Tia Coal Eelma tedio Center Front Left Front Right Rear Left Rear Right D brg ee ey act Lir qmime ir Leet mi 755 760A01 Series User Manual 755A01 032604 p65 18 2004 3 26 15 28 h Facon Chapter 2 Installation Instructions Other Connectors This motherboard includes interfaces for FLOPPY IDE HDD SATA USB 1394 IR module CPU fan system fan and others FLOPPY This motherboard includes a stand
31. cription Set pin 2 and pin 3 closed coer ED Set the pin opened 755 760A01 Series User Manual 755A01 032604 p65 28 2004 3 26 15 28 h Facon Chapter 2 Installation Instructions Clear CMOS Jumper CLS_CMOS This motherboard uses the CMOS RAM to store all the set parameters The CMOS can be cleared by removing the CMOS jumper How to clear CMOS 1 Turn off the AC power supply and connect pins 1 and 2 together using the jumper cap 2 Return the jumper setting to normal pins 2 and 3 locked together with the jumper cap 3 Turn the AC power supply back on i Normal status gt default 3 Clear CMOS B 3 Clear CMOS Jumper Warning 1 Disconnect the power cable before adjusting the jumper settings 2 Do not clear the CMOS while the system is turned on 755 760A01 Series User Manual 755A01 032604 p65 29 2004 3 26 15 28 oe R Fcon Chapter 2 Installation Instructions BIOS Protection Jumper FWH_EN The motherboard BIOS is inside the FWH If the jumper FWH_EN is set as disable Pin1 amp Pin2 the system BIOS is protected from being attacked by a serious virus such as the CIH virus You will be unable to flash the BIOS to the motherboard when the system BIOS is protected 4a gt E wee were ire Flash Write HEA Enable piy Default ni Flash Write Disable 3 OM N BlOS Protection Jumper LAN Disable Jumper LAN_DIS This jumper
32. e Fd Attention The pictures of objects used in this manual are just for your reference Please refer to the physical motherboard 755A01 English preface 031504 p65 7 2004 3 26 16 06 This page is intentionally left blank 755A01 English preface 031504 p65 8 2004 3 26 16 06 755A01 032604 p65 Thank you for buying Foxconn s 755 760A01 series motherboard This series of motherboard is one of our new products and offers superior performance reliability and quality at a reasonable price This motherboard adopts the advanced SiS 755 760 SiS 964 chipset providing users a computer platform with a high integration compatibility per formance price ratio This chapter includes the following information Main Features Motherboard Layout 1 2004 3 26 15 28 h F connn Chapter 1 Product Introduction Main Features Size e ATX form factor of 12 x 8 8 Microprocessor e Supports AMD Athlon64 Processor Hyper Transport Technology with 8 16 links e Supports AMD Athlon64 Processor Hyper Transport Technology up to 1600 MT s bandwidth Chipset e SiS Chipset SiS 755 760 North Bridge SiS 964 South Bridge System Memory HEHRE lili e Three 184 pin DDR DIMM slots e Supports PC3200 2700 2100 memory e Supports 128 256 512 Mb technology up to 3GB USB 2 0 Port a SE e Supports hot plug e Eight USB 2 0 ports four rear panel ports two onboard USB headers providing four extra ports e Supports
33. e Default Floppy Hard Disk CDROM This option allows you to set the boot device sequence The available setting values are Floppy LS120 Hard Disk CDROM ZIP100 USB FDD USB ZIP USB CDROM LAN and Disabled lt Boot Other Device Default Enabled With this function set to enabled the system will boot from some other devices if the first second third starting devices failed Swap Floppy Drive Default Disabled If it is set to enabled the label of FDD A and B can be exchanged The available setting values are Disabled and Enabled Boot Up Floppy Seek Default Enabled If it is set to enabled BIOS will activate the floppy drive during the system boot and the drive s indicator will flash after the activation The magnetic head will move back and forth from A to B The available setting values are Disabled and Enabled Boot Up NumLock Status Default On This option is used to set up the NumLock status after the startup When it is set to On the NumLock will be activated during system startup When it is set to off users can use the number keys instead of the arrow keys to move the cursor The available setting values are On and Off lt Gate A20 Option Default Fast This option is used to set up the A20 signal control necessary for access to the 1MB memory The available setting values are Normal and Fast Typematic Rate Setting Default Disabled If this option is enabled you can use the following two items
34. e controller for IEEE1394a on motherboard The VT6307 is a complete small package single chip PCI solution at 400Mbps low power seamless plug and play connections to the latest IEEE 1394 enabled devices LAN controller optional The RTL8110S 32 Gigabit Ethernet is a single chip solution for LAN on motherboard LOM applications and supports 10 100 1000 Mbps data transfer rates For K models The RTL8110C Ethernet is a single chip solution for LAN on motherboard LOM applications and supports 10 100 Mbps data transfer rates For L models 755 760A01 Series User Manual 755A01 032604 p65 6 2004 3 26 15 28 This chapter introduces the hardware installation process including the installation of the CPU and memory It also addresses the connection of your power supply use of the rear panel connectors connection of hard drive and floppy drive data cables and setting up various other feature of the motherboard Caution should be exercised during the in stallation process Please refer to the motherboard layout prior to any installation and read the contents in this chapter carefully This chapter includes the following information CPU Memory Power Supply Rear Panel Connectors Other Connectors Expansion Slots Jumpers 755A01 032604 p65 7 2004 3 26 15 28 Take note of the following precautions before you install components or change settings 1 Use a grounded wrist strap or touch a safely grounded object 2 Unplu
35. e playing Karaoke Playing Karaoke 1 Click the audio icon gei from the window tray at the bottom of the screen 2 Make sure the Sound Effect tab is selected 3 Select Voice Cancellation in the Karaoke column 755 760A01 Series User Manual 755A01 032604 p65 69 2004 3 26 15 28 Chapter 4 Driver CD Introduction alo Audie Coaligura tion SH oe F owed eet tedis ihdas aie Husain Pout Ten ranm Tei ra Eam hir F kwa hain Cirad Click here F Ha es 4 ker baaie 4 Click OK Install LAN Driver Click lt Install Driver gt from the main menu and enter the install driver menu as shown in fig 1 Click lt LAN Driver gt to start the installation 755 760A01 Series User Manual 2004 3 26 15 28 70 755A01 032604 p65 FOXxcOoM Chapter 4 Driver CD Introduction Install Sil3112 SATA RAID Driver Click lt Install Driver gt from the main menu and enter the install driver menu as shown in fig 1 Click lt Sil3112 SATA RAID gt to start the installation FOROOWY Lin E Co ib tile ee EE Bs T liS kbit Ai jimi irma 1 ir IE EHF FHF H hies D hi i a e p a l 4 a pama AS aes Led ee Install SuperUtilily From the main menu select lt Accessories gt as shown in following fig 1 Click lt SuperUtilily gt to start the setup FOMCOMN LTT PLY Coe r 755 760A01 Series User
36. ecedented high security and reliability with extra functions such as hotkey launch and powerful anti virus protection Features 1 Password Protection You can set a password for each HDD 2 Data Protection Hidden partitions can only be accessed during data back up or recovery Even reformatting the disk using FDISK or PQMAGIC will not allow access to the disk This means that data backed up in a hidden partition is very secure 3 Intelligent Menu Unavailable items will be displayed in gray For example if you haven t divided a hidden partition items like Release Hidden Partition Back up and Recovery will be displayed in gray and can t be selected And when you select an item the related information will appear on the bottom of the screen Disclaimer Please study this software program s specification carefully before using it The vendor should not be liable for any damage arising out of or in connection with the use of this program including liability for lost profit or data or any other damage whatsoever System Requirements 1 ATA5 or above compliant IDE HDD 2 FAT16 FAT32 NTFS files system 3 PS 2 keyboard or USB keyboard Hotkey Selection You should enter the CMOS setup interface first by pressing lt DEL gt during POST Power On Self Test Then select the SuperRecovery Hotkey option to adjust the hotkey settings in the BIOS Features menu There are 12 options LSHIFT L
37. eft Shift F1 F12 LSHIFT F12 is the default 68 755 760A01 Series User Manual 755A01 032604 p65 88 2004 3 26 15 28 Chapter 6 Special BIOS Functions Hard Disk Selection The hard disk selection menu will be displayed after you press the hotkey listing all the IDE HDDs installed in your system You can switch the highlight bar to make a selection and press Enter to confirm it Attention 1 Make sure that you have selected a HDD before entering the main menu 2 Make sure that the HDD you selected is ATA5 or higher For the HDDs lower than ATAS there will be a message of No Support in the HDD list menu listing beside the name of it 3 Only one HDD can be opreated at a time Note If you have assigned a password to the selected HDD you will be prompted to provide it before proceeding 755 760A01 Series User Manual 755A01 032604 p65 89 2004 3 26 15 28 R Fazon Chapter 6 Special BIOS Functions Main Menu Select a HDD to enter main menu There are five function items DIVIDE HID DEN PARTITION RELEASE HIDDEN PARTITION BACKUP RECOVERY and CHANGE PASSWORD You can switch the highlight bar to make a selec tion on the operation which should be performed on the HDD and confirm your selection by pressing Enter The following operation will be performed on the disk you selected i E PFITI I EESC BL ETE PRR E IES br FOF ERS FF oe ee mit iib i
38. empty empty x8 single rank or x16 x8 single rank or x16 x8 double rank x8 double rank x8 single rank or x16 x8 single rank or x16 x8 double rank x8 double rank x8 single rank or x16 x8 single rank or x16 x8 double rank x8 double rank Maximum CA2 Frequency MHz Socket 3 empty empty x8 single rank or x16 empty empty x8 double rank empty empty x8 single rank or x16 x8 double rank empty empty x8 single rank or x16 x8 double rank x8 single rank or x16 x8 double rank x8 single rank or x16 x8 double rank x8 single rank or x16 x8 double rank x8 single rank or x16 x8 double rank x8 single rank or x16 x8 double rank x8 single rank or x16 x8 double rank 755 760A01 Series User Manual 755A01 072104 p65 13 2004 7 21 8 27 a Chapter 2 Installation Instructions Memory Qualified Vendor List The following table lists the memory modules that have been tested and quali fied for use with this motherboard Vendor Tye Size Kingmax Kingmax Kingston Hynix Nanya Apacer Apacer Geil VDATA RAMBO RAMBO Transend Twinmos Samsung Note Make sure to use only the tested and qualified DDR modules listed above Other DDR modules manufactured by other ven dors may not be suitable for this motherboard 755A01 032604 p65 PC3200 DDR 400 PC2100 DDR 266 PC3200 DDR 400 PC3200 DDR 400 PC3200 DDR 400 PC3200 DDR 400 PC2700 DDR 333 PC3200 DDR 400 PC3200 DDR 40
39. figurations Menu lt Reset Configuration Data Default Disabled This option is used to set whether the system is permitted to automatically distribute IRQ DMA and I O addresses when each time the machine is turned on The setting values are Disabled and Enabled lt Resources Controlled By Default Auto ESCD This option is used to define the system resource control scheme If all cards you use support PnP then select Auto ESCD and the BIOS will automatically distributes interruption resources If the ISA cards you installed not support ing PnP you will need to select Manual and manually adjust interruption resources in the event of hardware conflicts However since this motherboard has no ISA slot this option does not apply lt IRQ Resources Press the lt Enter gt key then manually set IRQ resources lt PCI VGA Palette Snoop Default Disabled If you use a non standard VGA card use this option to solve graphic accelera tion card or MPEG audio card problems e g colors not accurately displayed The setting values are Disabled and Enabled lt Raid Card Boot First Default Disabled This option is used to set Raid card boot first The setting values are Dis abled and Enabled 755 760A01 Series User Manual 755A01 032604 p65 54 2004 3 26 15 28 h F con Chapter 3 BIOS Description PC Health Status PC Health Status Menu lt Smart Fan Control Default Disabled This option is used to contro
40. fter division is in process So you d better do the division against an empty HDD 2 At the same time the HDD capacity will decrease to make space for the hidden partition which is unavailable for your normal use r ENEE AIGE Pee 420 Ma ipy i LE A i W FE ae Release Hidden Partition This is used to release the hidden partition If you choose this item and press Y to confirm the system will be restarted to release the hidden partition But the released partition is still unavailable for you after the system is restarted It s necessary for you to enable it by using FDISK PQMAGIC or some other tools 755 760A01 Series User Manual 755A01 032604 p65 91 2004 3 26 15 28 h Facon Chapter 6 Special BIOS Functions Backup Select BACKUP to enter the Backup interface where you can find the following three sub function items BACKUP CMOS SETUP BACKUP PARTITION TABLE and BACKUP HARDDISK DATA Switch the highlight bar by pressing the arrow keys to make a selection and then press Enter to confirm your choice T F LE RM TO wll a i EFI PREDIEL 3H DAE BRP EEIT bili i Th Salk 1 Backup CMOS Setup 1 Supports backing up of the CMOS data 2 The backing up or recovery of CMOS data should be operated on a motherboard of the same model SLES 10 Coe HL FREE Be KY Le CERT LBS 2 Backup Partition Table This function can help to backup all partition tables including extended p
41. g the power cord before opening your chassis or touching 3 Hold components by their edges to avoid touching any exposed 4 Whenever you uninstall a component place it on a grounded R YeFoxcormTi Chapter 2 Installation Instructions Notes such as an attached power supply before handling components to avoid damaging them due to static electricity any components integrated circuits ICs anti static pad or into the anti static bag that it came in 755 760A01 Series User Manual 755A01 032604 p65 8 2004 3 26 15 28 h Facon Chapter 2 Installation Instructions CPU This motherboard supports AMD Athlon64 processors with a 1600 MT s band width and HyperThansport Technology L gt Attention The CPU pins must be properly aligned with the holes in the socket otherwise the CPU may be damaged Installation of CPU Follow these steps to install the CPU Unlock the socket by pressing the le ver sideways then lift it up to a 90 angle 90 DO O E i Cc Gap in the base 2 Align the cut edge to the gap in the base of the socket Carefully insert the CPU into the socket until it fits in place FEE Lei Push down the socket Cut edge lever to secure the CPU 3 When the CPU is in place press it firmly on the socket while you push down the socket lever to secure the CPU The lever clicks on the side tab to indicate that it is locked 755 760A01 Series User Manua
42. he OS shut down function If you use windows 98 ME 2000 XP click the Start button click Shut Down then click the OK button to shut down the computer The power supply should turnoff after Windows shuts down 2 Using the dual function power switch While the system is ON pressing the power switch for less than 4 seconds puts the system to sleep mode or to soft off mode depending on the BIOS setting Pressing the power switch for more than 4 seconds lets the system enter the soft off mode regardless of the BIOS setting 755 760A01 Series User Manual G 755A01 032604 p65 31 2004 3 26 15 28 755A01 032604 p65 This chapter tells how to change system settings through the BIOS Setup menus Detailed descriptions of the BIOS param eters are also provided You have to run the Setup Program when the following cases occur 1 An error message appears on the screen during the system POST process 2 You want to change the default CMOS settings This chapter includes the following information Enter BIOS Setup Main Menu Standard CMOS Features BIOS Features Advanced BIOS Features Setup Advanced Chipset Features Setup Integrated Peripherals Power Management Setup PnP PCI Configurations Setup PC Health Status Frequency Voltage Control Load Fail Safe Defaults Load Optimized Defaults Set Supervisor User Password Save amp Exit Setup Exit Without Saving 32 2004 3 26 15 28 R HFoaozcon Chapter 3 BIOS Description Enter BIOS Setup
43. is used to enable or disabled onboard LAN Close pin 1 and 2 the onboard LAN is enabled Close pin 2 and 3 the onboard LAN is disabled i EE PE Ta Q LAN_DIS i 12 3 Onboard LAN Enable Onboard LAN Disable C 755 760A01 Series User Manual 755A01 032604 p65 30 2004 3 26 15 28 R 4 FoxcorTi Chapter 2 Installation Instructions Starting up for the first time 1 After making all the connections replace the system case cover 2 Be sure that all switches are off 3 Turn on the devices in the following order a Monitor b External SCSI devices starting with the last device on the chain c System power 4 After applying power LED on the system front panel case lights up For ATX power supplies the system LED lights up when you press the ATX power switch If your monitor complies with green standards or if it has a power standby feature the monitor LED may light up or switch between orange and green after the system LED turns on The system then runs the power on tests While the tests are running the BIOS beeps or additional mes sages appear on the screen If you do not see anything within 30 seconds from the time you turned on the power the system may have failed a power on test Check the jumper settings and connections or call your retailer for assistance 5 At power on hold down lt Delete gt to enter BIOS Setup Follow the instructions in Chapter 3 Powering off the computer 1 Using t
44. it will refuse you to continue Under the menu Advanced BIOS Features Setup if you select Setup in Secu rity Option the screen will prompt you to enter password only when you enter CMOS setting program Save amp Exit Setup Select this option and press Enter it will show the following message in the center of screen SAVE to CMOS and EXIT Y N At this time press lt Y gt to save your amendment in CMOS and exit from this program press lt N gt lt ESC gt to return main menu Exit Without Saving Select this option and press Enter it will show the following message in the center of screen Quit Without Saving Y N At this time press lt Y gt to exit CMOS but it does not save your amendment in CMOS press lt N gt lt ESC gt to return main menu 755 760A01 Series User Manual 755A01 032604 p65 58 2004 3 26 15 28 755A01 032604 p65 The utility CD that came with the motherboard contains useful software and several utility drivers that enhance the mother board features This chapter includes the following information Utility CD content Start to install drivers Install IDE Driver Install SiS SATA RAID Install AGP Driver Install Direct X 9 0b Install USB2 0 Driver Using 4 6 Channel Audio Install LAN Driver Install Sil8112 SATA RAID Install SuperUtility Install Adobe Reader Install Norton Internet Security 2004 59 2004 3 26 15 28 Facon Chapter 4 Driver CD Introduction
45. ke up On LAN WOL Through the Wake Up On LAN function a wake event occurring from the net work can wake up the system To utilize this function please be sure to use an ATX 12V power supply with a 5VSB line capable of delivering a current of at least 1A and a LAN adapter which supports this function Then connect the header to the relevant connector on the LAN adapter set PCIPME Power Up Control to Enabled in the Power Management Setup section of the CMOS SETUP Save and exit then boot the operating system once to make sure this function takes effect Signal for waking up GND 1 5VSB WOL 755 760A01 Series User Manual 755A01 032604 p65 23 2004 3 26 15 28 R Facon Chapter 2 Installation Instructions Wake up on Modem WOM Through this function systems in suspend or soft off mode can be waked up by a ring signal received from the internal modem When this function is used be sure an internal modem card which supports this function is used Then con nect the header to the relevant connector on the modem card set RING Power Up Control to Enabled in the Power Management Setup section of the CMOS SETUP Save and exit then boot the operating system once to make sure this function takes effect m Modem wake up Spa kk dalha GND F I d 1 5V_SB_SYS WOM S ATA Connectors SATA1 SATA2 SATA3 SATA4 The S ATA header is used to connect the S AT
46. l 755A01 032604 p65 9 2004 3 26 15 28 R Facon Chapter 2 Installation Instructions Installation of CPU Fan New technology allows processors to run at higher and higher frequencies To avoid problems arising from high speed operation for example overheating you need to install the proper fan The following procedure is provided for reference only please refer to your CPU fan user guide for the actual procedure 1 Locate the CPU retention mechanism 2 If required apply a light coating of base surrounds the CPU socket silica gel to the top of the CPU NOTE The CPU heatsink may have a pre applied thermal compound In that case the silica gel is not required 3 Attach the fan to the base 4 Connect the fan s power cable to the appropriate 3 pin terminal on the motherboard Warning Excessive temperature will severely damage the CPU and system Therefore make sure that the cooling fan works nor mally at all times in order to prevent overheating and damaging to the CPU 755 760A01 Series User Manual 755A01 032604 p65 10 2004 3 26 15 28 R Foxconn Chapter 2 Installation Instructions CPU Qualified Vendor List The following table lists the CPUs that have been tested and qualified for use with this motherboard Athlon64 3000 Athlon64 3200 Athlon64 3400 755 760A01 Series User Manual 755A01 032604 p65 11 2004 3 26 15 28 R Hromozom Chapter 2 Installation Instructions
47. l the smart fan Shutdown Temperature Default Disabled This option is used to set the system temperature upper limit When the temperature exceeds the setting value the motherboard will automatically cut off power to the computer The setting values are 60 C 140 F 65 C 149 F 70 C 158 F Disabled Vecp 3 3v 5v 12v The current voltages will be automatically detected by the system lt CPU Temp The current CPU temperature will be automatically detected by the system lt System Temp1 The system temperature1 will be automatically detected by the system System Temp2 The system temperature2 will be automatically detected by the system lt CPU FAN Speed The CPU fan speed will be automatically detected by the system lt System FAN1 Speed The system fan1 speed will be automatically detected by the system 755 760A01 Series User Manual 755A01 032604 p65 55 2004 3 26 15 28 h F conmn Chapter 3 BIOS Description Frequency Voltage Control Frequency Voltage Control Menu lt Auto Detect PCI Clk Default Enabled This option is used to set whether the clock of an unused PCI slot will be disabled to reduce electromagnetic interference The setting values are Dis abled and Enabled Async SRC ZCLK AGP PCI Default Disabled The setting values are 100 133 66 33Mhz 100 150 75 37Mhz 100 133 80 40Mhz and Disabled Spread Spectrum Default Disabled If you enable spread spectrum i
48. ly cable and pins are properly aligned with the connector on the motherboard Firmly plug the power supply cable into the connector and make sure it is secure ATX 12V Power Connector ATX 20 pin Power Connector 5V GND GND GND 3 3V 5VSB GND GND GND 3 3V F Attention You have to press the power button for more than four seconds if you change the default Instant off setting to Delay 4 Sec for the Soft Off by Power Button option in the BIOS Power Management Setup 16 755 760A01 Series User Manual 755A01 032604 p65 16 2004 3 26 15 28 h Foxconn Chapter 2 Installation Instructions Rear Panel Connectors This motherboard provides the following ports as below LANPort Parallel Port 1394Port Printer Port optional e Line in Line out Cn MIC a PS 2 Mouse Port 2 PS 2 Keyboard Pot 1 COM1 VGA Connector USB 2 0 Port only for 760A01 PS 2 Mouse Port This green 6 pin connector is for a PS 2 mouse PS 2 Keyboard Port This purple 6 pin connector is for a PS 2 keyboard Serial Ports COM1 This two 9 pin COM1 COM2 ports are for pointing devices or other serial devices VGA Connector only for 760A01 The VGA connector is for output to VGA compatible device Parallel Port Printer Port The 25 pin port connects a parallel printer a scanner or other devices USB 2 0 Ports These four Universal Serial Bus USB ports are availa
49. main as it is in S1 mode the computer can beresumed at any time When you select S3 STR mode the power will be cut off after a delay period The status of the computer before it enters STR will be saved in memory and the computer can quickly return to previous status when the STR function wakes When you select S1 amp S3 mode the system will automatically select the delay time lt Power Management Default User Define This option is used to set the power management scheme Available settings are User Define Min Saving and Max Saving lt Suspend Mode Default Disabled This option is used to set the idle time before the system enters into sleep status The setting values are Disabled and 1 Min 1 hour lt Video Off Option Default Susp Stby gt Off This option is used to set video off option The setting values are Always On Suspend gt Off Susp Stby gt Off All Modes gt Off 755 760A01 Series User Manual 755A01 032604 p65 50 2004 3 26 15 28 4Foxcom Chapter 3 BIOS Description Video Off Method Default DPMS Supported This option is used to define the video off method Blank Screen mode means that after the computer enters power saving mode only the monitor will close however the vertical and horizontal scanning movement of the screen continues When you select the V H SYNC Blank mode the vertical and horizontal scanning movement of screen stops when the computer ente
50. n 1 44M 3 5in and 2 88 M 3 5in Video The following table is provided for your reference in setting the display mode for your system VGA SEGA SVGA or PGA monitor adapters Monochrome adapter including high resolution monochrome adapters Halt On This category determines whether or not the computer will stop if an error is detected during powering up All Errors Whenever the BIOS detects a nonfatal error the PMNS system wi stop and you wil be prompted No Errors The system boot will not stop for any errors that ma be detected All But Keyboard The system boot will not stop for a keyboard error ee butit wil sop tor al ober ens All But Diskette The system boot will not stop for a diskette error but ee twilstoptoraloherenos oo o All But Disk Key The system boot will not stop for a keyboard or a a Sawcces 755 760A01 Series User Manual 755A01 032604 p65 36 2004 3 26 15 28 R TFoxcorT Chapter 3 BIOS Description Memory This is a Displays Only Category detemined by POST Power On Self Test of the BIOS Base Memory The BIOS POST will detemine the amount of base or conventional memory installed in the system Extended Memory The BIOS determines how much extended memory is present during the POST Total Memory Total memory of the system 755 760A01 Series User Manual 755A01 032604 p65 37 2004 3 26 15 28 h F conmn Chapter 3 BIOS Description BIOS Features BIO
51. nsasnacnensomniotindayniisniotenstontetosiiantimboasiatmemneaas 33 EE T EE E E E E E EE E E 33 Standard CMOS Features cccccssssssecsesscsssseeecessasseeeeessosanseesoosseeseessoass 35 BIOG FEaAlUrES cscnsacunsonsxvecnceesmndautrescasnomeveansseoucxeeessanansneaasmutacenisutuastesreses 38 Advanced BIOS Features sicsiieniscctssnsusvsninanedawsusneceunedexviencncssuiaeinucavedvestteneaans 39 Advanced Chipset Features cccccccccssssssseeeeeasesseeeeeseeeeeeeeeesanseeeeeesaees 42 DRAM COPA ON sss secretes sanencacanesersecaconsvensueessveactecesteeansraceseereeesussereere 43 integrated SUD VANS seta ciivicitcnievivexcenaninvyindesceinan sntemiiessubasacenteusentaeniamadateentes 45 Power Management Setup xscnavtescccscetecssceduaacanvecesvcneis cess yeesvactenbintecceg enn teaate 50 PnP PCI Configurations acsceeveserrs wesxenenceeavsasvsnxedineswanerecsapeeansaransannerenseddeaneretsns 54 PC PIG AACS seeecxec sys nvaxeiouncaanestioueenesigeiccusainsentenecaadp sc ucecassealjaninndavmiiedetenesias 55 Frequency Voltage Control scc tcesssacccaseatssnciitntvaweccdniesasciarincbenetinrenteleedeanibeads 56 Load Fail Safe Defaults ssocnssssxsncersnasesniavectavvanestcsessvrrcssateumncateasuauinessateueenan 57 Load Optimized Defaults ic wxscccciex wisenedteentcinncee nical axanccosdaiassuentaiecianunndeelieenbencsensens 57 Set Supervisor User Password ccccccccessseeeeeeeseeeseeeeeesaeseeeeeeseaseeeeeees 57 SEa o E 58 EXIF WV AMICI SAVINO
52. nt BIOS then the following picture will appear Superlipdate asirai MILE Tate a iii iin Frei Liat Ae 755 760A01 Series User Manual 755A01 032604 p65 79 2004 3 26 15 28 h Facon Chapter 5 Directions for Bundled Software 5 Now is updating SuperUpdate 6 Click lt Restart gt SuperUpdate Pree i LTS Tan era A e pr pe HOES opelade cor wi bol s AET EEE H TEH i si Ny baid CORES dpi n il ki bia 755 760A01 Series User Manual 755A01 032604 p65 80 2004 3 26 15 28 h Facon Chapter 5 Directions for Bundled Software Update BIOS On line 1 Click lt Liveupdate gt to automatically update the BIOS from the internet SuperUpdate 2 The following procedure is the same as Update BIOS from local image 755 760A01 Series User Manual D 755A01 032604 p65 81 2004 3 26 15 28 Chapter 5 Directions for Bundled Software 1 FOXxXcConM SuperLogo JES lesa SuperLogo is a Windows utility that allows users to change the BIOS sign on logo The utility is able to replace and backup the BIOS logo and update and backup the BIOS image within the Windows environment SuperLogo features 1 Supports Win2000 and WinXP 2 Supports 4Mb size flash parts flash write method is independent with flash type 3 Simple and easy to operate with a user friendly graphics interface 4 Supports BMP and JPEG graphic format files The best color is 16 or 256 colors The best resolution is 136 x 8
53. nt Setup All the items of Green function features can be set up through this menu PnP PCI Configurations The system s PnP PCI settings and parameters can be modified through this menu PC Health Status This will display the current status of your PC Frequency Voltage Control Frequency and voltage settings can be adjusted through this menu Load Fail Safe Defaults The default BIOS settings can be loaded through this menu Load Optimized Defaults The optimal performance settings can be loaded through this menu however the stable default values may be affected Set Supervisor User Password The supervisor user password can be set up through this menu Save amp Exit Setup Save CMOS value settings to CMOS and exit setup Exit Without Saving Abandon all CMOS value changes and exit setup 755 760A01 Series User Manual 755A01 032604 p65 34 2004 3 26 15 28 h FOoxcomn Chapter 3 BIOS Description Standard CMOS Features This sub menu is used to set up the standard CMOS features such as the date time HDD model and so on Use the arrow keys select the item to set up and then use the lt PgUp gt or lt PgDn gt keys to choose the setting values frre 2 Ui 7 i 1 E 7 7 m F i Standard CMOS Features Menu Date This option allows you to set the desired date usually as the current date with the lt day gt lt month gt lt date gt lt year gt format day weekday from Sun to Sat defined
54. ord before adding or removing expansion cards 3 Remove the bracket opposite the slot that you intend to use 4 Align the card connector with the slot and press firmly until the card is completely seated on the slot 5 Secure the card to the chassis with the screw you removed earlier AGP Qualified Vendor List The following table lists the AGP cards that have been tested and qualified for use with this motherboard 755 760A01 Series User Manual 755A01 032604 p65 27 2004 3 26 15 28 Chapter 2 Installation Instructions Video Memory MS GeForce 4 MX440 8X ATI Radeon 7000 7917 GeForce 4 MX 440 ATI 9500 8X ATI 9600 8X V7100 8X V7700 8X Note Make sure to use only the tested and qualified AGP cards listed above Other AGP cards manufactured by other ven dors may not be suitable for this motherboard Jumpers Users can change the jumper settings on this motherboard if needed This section explains how to use the various functions of this motherboard by chang ing the jumper settings Users should read the following contents carefully prior to modifying any jumper settings Description of Jumpers 1 For the jumpers on this motherboard pin 1 can be identified by the silk screen printed A next to it However in this manual pin 1 is simply labeled as 1 2 The following table provides some explanation of the jumper pin settings Users should refer to this when adjusting jumper settings Des
55. p Go to Fan System Fant System Fan2 page speed speed optional Link to Foxconn Website CPU Fan speed Exit Program Minimize Window Adjust CPU SuperStep on line Help Fan warning About SuperStep criteria Adjust system Fan2 warning criteria Adjust system Reset the Apply the Fan1 warning warning criteria adjust criteria to default ments settings 755 760A01 Series User Manual 755A01 032604 p65 74 2004 3 26 15 28 Goto Voltage Adjust voltages warning page criteria upper limit Cd wr GE EN E E dN Cm E E A Ee a 3 Current voltage readings SuperS tea Reset the warning Apply the Adjust voltages criteria to default adjustments warning criteria settings Lower limit Go to Temperature page EFI Tomparalir m i Current CPU Di mm pS ae Fi Adjust CPU tem iemperature perature warning Sprice lcrperwi ere criteria Current syster EE Temperature ji Adjust system temperature SupefStep ee warning criteria Reset the warn Apply the adjust ing criteria to ments default settings 755 760A01 Series User Manual 755A01 032604 p65 75 2004 3 26 15 28 h Facon Chapter 5 Directions for Bundled Software Go to Clock page Current CP Current AGP clock Clock Current PCI clock Adjust the CPU Ratio Adjust the CPU FSB Superstep Reset to the default Apply the adjustments settings Go to Alarm Check for the system to auto matically provide warning message Superstep Rese
56. page 52 lt AMD K8 Cool amp Quiet Control Default Auto This option is used to control AMD K8 Cool amp Quiet function 755 760A01 Series User Manual 755A01 032604 p65 51 2004 3 26 15 28 Chapter 3 BIOS Description PM Wake UP Events Menu IRQ 3 7 9 15 NMI Default Enabled This option is used to enable or disable IRQ 3 7 9 15 NMI IRQ 8 Break Suspend Default Disabled This option is used to enable or disable IRQ8 break suspend RING Power Up Control Default Enabled If this option is enabled it allows the system to resume from a software power down or power saving mode whenever there is an incoming call to an in stalled fax modem This function needs to be supported by the relevant hard ware and software The setting values are Disabled and Enabled lt PCIPME Power Up Control Default Enabled This option is used to enable or disable the system to be waken up by PCI card PS2KB Wakeup from S3 S4 S5 Default Hot Key This option used to set which action will wake up PS 2 keyboard from S3 S4 S5 status The hotkey is Ctrl Alt Backspace The setting values are Any Key Hot Key Password lt PS2MS Wakeup from 3 S4 S5 Default Click This option used to set which action will wake up PS 2 mouse from S3 S4 S5 status The setting values are Disabled Click Move amp Click Power UP by Alarm Default Disabled This option is used to set the timing of the start up function In order to use this
57. provides support for 6 Channel audio output including 2 front 2 rear 1 center and 1 subwoofer channel ALC655 allows the board to attach 4 or 6 speakers for a better surround sound effect This section will tell you how to install and use the 4 6 Channel audio function on the board Installing the Audio Driver You need to install the driver for the Realtek ALC655 chip before you can use the 4 6 Channel audio function Click lt Install Driver gt from the main menu and enter the install driver menu as shown in fig 1 Click lt Audio Driver gt to start the installation 755 760A01 Series User Manual 755A01 032604 p65 64 2004 3 26 15 28 R Yeocon Chapter 4 Driver CD Introduction Attaching Speakers To perform multichannel audio operation connect multiple speakers to the system You should connect the same number of speakers as the audio chan nels you will select in the software utility 2 Channel Analog Audio Output The audio connectors on the rear panel already provide 2 Channel analog au dio output The rear panel s audio connectors can be transformed to 4 6 Chan nel analog audio connectors automatically when you select the correct setting in the software utility For information about the setting refer to Selecting 4 or 6 Channel Setting later in this section Make sure all speakers are connected to Line out connectors Diverse connec tor configurations for 2 4 and 6 Channel using rear panel connectors a
58. re described below 2 Channel Analog Audio Output Line in Line out Front channels ee da CE _ w Description Line out Line in and Microphone functions all exist under 2 Channel configuration 755 760A01 Series User Manual 755A01 032604 p65 65 2004 3 26 15 28 YeFocon Chapter 4 Driver CD Introduction 4 Channel Analog Audio Output Line out Rear channels ii Line out Front channels amp mc Description Line in is converted to Line out under the 4 Channel configuration 6 Channel Analog Audio Output Line out Rear channels eon Line out Front channels 13 M Cm F o Line out Center and Subwoofer channels Description Both Line in and Microphone are converted to Line out under the 6 Chan nel configuration 755 760A01 Series User Manual 755A01 032604 p65 66 2004 3 26 15 28 JeFoxcomT Chapter 4 Driver CD Introduction Digital Audio Output S PDIFCable 6CH_Bracket Coaxial S PDIF jack Description Connect the S PDIF speakers to the Coaxial S PDIF jack Selecting 4 or 6 Channel Setting 1 Click the audio icon gei from the Windows tray bar at the bottom of the screen 2 Select any surround sound effect you prefer from the Environment pull down menu under the Sound Effect tab ATI Audio Configuration i alx LTEN 2 l RS hi Conair Eon AT fo homer al Seemed EDC Eoxlice Seeder Cee car etic Seder Tar Click he
59. re and the pull down menu will appear 755 760A01 Series User Manual 67 755A01 032604 p65 67 2004 3 26 15 28 Chapter 4 Driver CD Introduction 3 Click the Speaker Configuration tab Click here 4 The following window appears Click here 5 Select the multi Channel operation you prefer from Number of Speakers 6 Click OK 755 760A01 Series User Manual 755A01 032604 p65 68 2004 3 26 15 28 Chapter 4 Driver CD Introduction a Testing the Connected Speakers To ensure 4 or 6 Channel audio operation works properly you may need to test each connected speaker to make sure every speaker works properly If any speaker fails to sound then check whether the cable is inserted firmly to the connector or replace the bad speakers with good ones Testing Each Speaker 1 Click the audio icon gei from the window tray bar at the bottom of the screen 2 Click the Speaker Test tab 3 The following window appears REF Hie Dao mia O EF l O iT Malla ie ft oe oo i Jri Pal Center E Front Right Rear Right Subwoofer 4 Select the speaker which you want to test by clicking on it Playing Karaoke The Karaoke function will automatically remove human voice lyrics and leave melody for you to sing the song The function can only be used with the 2 Channel audio configuration so make sure 2 channels mode is selected in the Number of Speakers column befor
60. rs power saving mode DPMS Supported mode is a new screen power management system and it needs to be supported by the monitor you re using lt Switch Function Default Break Wake This option is used to enable or disable switch function to wake up The setting values are Break Wake and disabled lt MODEM Use IRQ Default NA This option is used to set the IRQ in which the MODEM can use The system will automatically wake up when the Modem receives an incoming call Hot key Function As Default Power Off The option is used to define the hot key function The available setting values are Disabled Power off Suspend lt HDD Off After Default Disabled This option is used to define the continuous HDD idle time before the HDD enters power saving mode The setting values are Disabled and 1 Min 15 Min lt Power Button Override Default Instant Off This option is used to set the power down method This function is only valid for systems using an ATX power supply When Instant Off is selected press the power switch to immediately turn off power When Delay 4 Sec is selected press and hold the power button for four seconds to turn off power lt Power State Resume control Default Always Off This option is used to control power resume state The available setting val ues are Always Off Always On Keep Pre State lt PM Wake Up Events Press enter to set the items of PM wake up Events Please refer to
61. rt Default Disabled Use this option to enable or disable AGP fast write support lt AGP Data Transfer Rate Default Auto Use this option to set AGP data rate System BIOS Cacheable Default Disabled Select Enabled to allow catching of the system BIOS which may improve performance If any other program writes to this memory area a system error may result The available setting values are Disabled and Enabled 755 760A01 Series User Manual 755A01 032604 p65 42 2004 3 26 15 28 THFoOxcormT Chapter 3 BIOS Description TEETEREI elmi i Hep ajm Fe WE Fish Eel fis fagis beleale f iu ipi DRAM Configuration Menu HT_Width Default Auto The available setting values are 8 bits 16 bits and Auto HT_Speed Default 800MHz The available setting values are 200MHz 400 MHz 600 MHz and 800 MHz lt 1T 2T Memory Timing Default 2T Optional The available setting values are Auto 1T 2T DDR Timing Setting by Default Auto The available setting values are Manual and Auto Max Memclock Mhz Default 200 The available setting values are 100 133 166 and 200 CAS Latency Default Auto The available setting values are CL 2 0 CL 2 5 CL 3 0 and Auto Row cycle time lt tRC gt Default Auto The available setting values are Auto 7 22 Bus Clocks Row refresh cyc time lt tRFC gt Default Auto The available setting values are Auto 9 24 Bus Clocks lt RAS to
62. s Menu Hard Disk Boot Priority This option is used to select the priority for HDD startup After pressing lt Enter gt you can select the HDD using the lt PageUp gt lt PageDn gt or Up Down arrow keys and change the HDD priority using lt gt or lt gt you can exit this menu by pressing lt Esc gt Virus Warning Default Disabled This option is used to set up the virus warning message for the IDE HDD boot sector When set to Enabled a warning message will appear on the screen if any program wants to write any information to this sector and will give an audible warning The available setting values are Disabled and Enabled Note Such function provides protection to the startup sector only it does not protect the entire hard disk CPU Internal Cache Default Enabled This option is used to turn on or off the CPU L1 and L2 cache The available setting values are Disabled and Enabled External Cache Default Enabled This option is used to turn on or off the CPU external cache The available setting values are Disabled and Enabled lt Quick Power On Self Test Default Enabled With this function enabled the system will skip the normal test while starting up therefore reducing the overall start up time The available setting values are Disabled and Enabled 755 760A01 Series User Manual 755A01 032604 p65 39 2004 3 26 15 28 R HFoOxcorT Chapter 3 BIOS Description First Second Third Boot Devic
63. s for Bundled Software SEJO EE S E E E S E EA E A A E E E E E R DUD EE OGG roisia iE Rea Ei P EO i E E E Ge lt cset Chapter O Special BIOS Functions SPEE e EE S Su uperBIOS PrOte eee ae erent eer irainik i aiea ee eee ee Uo epe 5 2 216 e ee eee ane ere ee ote ee Ae serene ee eee eee cs SUDGT A CCOV EMF tpcnsiceseenecsacancntmennegeiuecamoiiaddltyscseacsnaacuneunaaunratueusenanepecesuaunooie 755A01 English preface 031504 p65 6 2004 3 26 16 06 Warning 1 Attach the CPU and heatsink using silica gel to ensure full contact 2 It is suggested to select high quality certified fans in order to avoid damage to the motherboard and CPU due to high temperature 3 Never turn on the machine if the CPU fan is not properly installed 4 Ensure that the DC power supply is turned off before inserting or removing expansion cards or other peripherals especially when you insert or remove a memory module Failure to switch off the DC power supply may result in serious damage to your system or memory module Warning We cannot guarantee that your system will operate normally while over clocked Normal operation depends on the over clock capacity of your device F Attention Since BIOS programs are upgraded from time to time the BIOS description in this manual is just for reference We do not guarantee that the content of this manual will remain consistent with the actual BIOS version at any given time in the futur
64. s used to connect speaker of the chassis a oe g i el Bid i m ii a T Jag a a_i 1 SPK Pull high a siia A Aia 1 EMPTY m S H pe NC o E te Qe SPKJ Ope k om i ae 4 d 7 sah Bs E Thee SPEAKER Expansion Slots This motherboard includes five 32 bit Master PCI bus slots and one AGP slot PCI Slots The expansion cards can be installed in the five PCI slots When you install or take out such cards you must make sure that the power plug has been pulled out Please read carefully the instructions provided for such cards and install and set the necessary hardware and software for such cards such as the jumper or BIOS settings m E f r sa a ba ee Me z a _ i mia igh ged re i Ei i m J a RS mE 1 i PCI Slots 755 760A01 Series User Manual 755A01 032604 p65 26 2004 3 26 15 28 R h Fozronn Chapter 2 Installation Instructions AGP Slot This motherboard has an AGP slot that supports 1 5V AGP cards AGP is an interfacing specification designed to display 3D images It provides a specialized 66Mhz 32 bit channel to allow the graphic controller to directly access the master memory and supports 4X and 8X speeds oe pe ere re re AGP Slot Installing an expansion card 1 Before installing the expansion card read the documentation that came with it and make the necessary hardware settings for the card 2 Make sure to unplug the power c
65. t No FDD For WIN 95 Default Yes If you are using the Windows 95 and running a system with on floppy drive select Yes for this option to ensure compatibility with Windows 95 logo certification The available setting values are No and Yes lt Video BIOS Shadow Default Enabled This option is used to enable or disable Video BIOS Shadow If you enable this option the video BIOS will be copied to RAM Video shadow will increase the video speed The available setting values are Disabled and Enabled Full Screen LOGO Show Default Enabled This option allows you to enable or disable the full screen logo The available setting values are Disabled and Enabled lt Small Logo EPA Show Default Disabled This option allows you to enable or disable the EPA logo The available setting values are Disabled and Enabled 755 760A01 Series User Manual 755A01 032604 p65 41 2004 3 26 15 28 h F conmn Chapter 3 BIOS Description Advanced Chipset Features Advanced Chipset Features Menu DRAM Configuration Default Press Enter Press enter to set the items about DRAM Configuration Please refer to page 43 lt AGP Aperture Size Default 64MB This option defines the size of the aperture if you use an AGP graphic adapter The aperture is a portion of the PCI memory address range dedi cated for graphic memory address space Note This function does not work when onboard VGA is used lt AGP Fast Write Suppo
66. t Supervisor User Password The preferential grade of Supervisor password is higher than user password You can use supervisor password to start into system or enter into CMOS set ting program to amend setting You can also use user password to start into system or enter into CMOS setting menu to check but if you have set supervisor password you cannot amend setting When you select Set Supervisor User Password it will appear the following message in the center of screen which will help you to set password Enter Password Enter your password not exceeding 8 characters then press lt Enter gt the pass word you have been enter now will replace the previous password When the system requires you to determine this password you can enter this password and press lt Enter gt If you do not need this setting you can press lt Enter gt when the screen prompts you to enter password and the screen will appear the following message to show this function invalid In this case you can freely enter into system and CMOS setting program PASS WORD DISABLED Press any key to continue 755 760A01 Series User Manual 755A01 032604 p65 57 2004 3 26 15 28 4Foxcornm Chapter 3 BIOS Description Under the menu Advanced BIOS Features Setup if you select System in Security Option the screen will prompt you to enter password once the system is started or you want to enter CMOS setting program If the password is wrong
67. t can significantly reduce the EMI ElectroMagne tic Interference generated by the system 755 760A01 Series User Manual 755A01 032604 p65 56 2004 3 26 15 28 4rFoxcom Chapter 3 BIOS Description Load Fail Safe Defaults Select this option to press Enter it will pop out a dialogue box to allow you to load default set by BIOS Select lt Y gt and then press Enter to load default Select lt N gt and press Enter it will not load The defaults set by BIOS have set the basic functions of system in order to ensure the stability of system But if your com puter fails to properly run you may load the default to make the system recover normal then carry out failure testing in next step If you only want to load the default in an option you can select this option and press the key F6 Load Optimized Defaults Select this option and press Enter it will pop out a dialogue box to let you load the optimized defaults set by BIOS Select lt Y gt and then press Enter to load the optimized defaults Select lt N gt and press Enter it will not load The defaults set by BIOS have set the optimized performance parameters of system to improve the performances of system components But if the optimized performance parameters to be set cannot be supported by your hardware devices it will cause system to make mistakes or not stable If you only want to load the optimized defaults in an option you can select this option and press the key F7 Se
68. t to the Apply the default settings changes 755 760A01 Series User Manual 755A01 032604 p65 76 2004 3 26 15 28 R Focon Chapter 5 Directions for Bundled Software a gt RUPEES ERIare SuperUpdate SuperUpdate is a Windows utility that allows users to backup and upgrade the system BIOS SuperUpdate features 1 Supports Win2000 and WinXP 2 Supports 4MB size flash parts flash write method is independent of flash type 3 Simple and easy to operate with a user friendly graphics interface Using SuperUpdate Browse BIOS bin file Perform the BIOS update from local HDD from local image Link to Foxconn Website Exit Program Minimize Window SuperUpdate on line Help About SuperUpdate Upgrating BIOS via Backup system internet automati BIOS to an image cally file 755 760A01 Series User Manual 755A01 032604 p65 77 2004 3 26 15 28 R Facon Chapter 5 Directions for Bundled Software Bakeup BIOS to local image 1 Click lt Backup gt to backup current BIOS file Fils io ra as aio ira jram BiH Fie mH Carel 2 Click lt OK gt to finish the backup process ee morea Ses Update BIOS from local image 1 Click lt Load gt to load the BIOS file SuperuUupdate 755 760A01 Series User Manual 755A01 032604 p65 78 2004 3 26 15 28 2 Click lt Update gt the following message will appear 3 Click lt Yes gt to backup the curre
69. tall driver menu as shown in fig 1 Click lt IDE Driver gt to start the installation 755 760A01 Series User Manual 755A01 032604 p65 61 2004 3 26 15 28 Chapter 4 Driver CD Introduction Install SiS SATA RAID Click lt Install Driver gt from the main menu and enter the install driver menu as shown in fig 1 Click lt SiS SATA RAID gt to start the installation FOuOOM Utile Cp Peal eni mirr baled lie bee unl ms a podad e a Install AGP Driver Click lt Install Driver gt from the main menu and enter the install driver menu as shown in fig 1 Click lt AGP Driver gt to start the installation 755 760A01 Series User Manual 755A01 032604 p65 62 2004 3 26 15 28 FOXxcOoM Chapter 4 Driver CD Introduction Install DirectX 9 0b Click lt Install Driver gt from the main menu and enter the install driver menu as shown in fig 1 Click lt DirectX 9 0b gt to start the installation Install USB 2 0 Driver Click lt Install Driver gt from the main menu and enter the install driver menu as shown in fig 1 Click lt USB 2 0 Driver gt to open the USB 2 0 Installation guide Please read the guide carefully and select the relevant installation method Read this guide carefully 755 760A01 Series User Manual 755A01 032604 p65 63 2004 3 26 15 28 Facon Chapter 4 Driver CD Introduction Using 4 6 Channel Audio The motherboard is equipped with the Realtek ALC655 chip which
70. to see the typematic rate and the typematic delay settings for your keyboard The avail able setting values are Disabled and Enable Typematic Rate Chars Sec Default 6 Use this option to define how many characters per second a held down key generated Typematic Delay Msec Default 250 Use this option to define how many milliseconds must elapse before a held down key beings generating repeat characters 755 760A01 Series User Manual 755A01 032604 p65 40 2004 3 26 15 28 R HFOXCONN Chapter 3 BIOS Description Security Option Default Setup When it is set to setup a password is required to enter the CMOS Setup screen when it is set to system a password is required not only to enter CMOS Setup but also to startup your PC as well lt APIC Mode Default Enabled This option is used to enable or disable APIC mode The available setting values are Disabled and Enabled MPS Version Control For OS Default 1 4 This option is used to set up the version of MPS Table used in NT4 0 OS OS Select For DRAM gt 64MB Default Non OS2 This option is only required if you have installed more than 64 MB of memory and you are running the OS 2 operating system Otherwise leave this option at the default lt HDD S M A R T Capability Default Disabled This option is used to enable or disable hard disk s S M A R T Support function The available setting values are Disabled and Enabled Repor
71. ttings you made 2 Recover Partition Table This function can help to recover all partition tables including extended partitions Pe fee me realig rami La weer pari Dilan sable i Frapp BES a prli r sifar ay ip pe isap ss 2 755 760A01 Series User Manual 755A01 032604 p65 95 2004 3 26 15 28 ee QR WFoxcorT Chapter 6 Special BIOS Functions 3 Recover Hard disk Data This option is used to restore the backed up data from the hidden partition Bee yma nere Se peur HEF dois Pee bidden peril iml Frane ERG ve saly pr ang en be bpp bp rasijesp s 4 Back to Main This option is used to quit the Recovery interface CHANGE PASSWORD Introduction Select CHANGE PASSWORD to enter the Change Password interface 1 Enter the old password first Press ENTER if password is null 2 Enter the new password Then enter the same again to confirm it 3 Press Enter for null password 4 The password will be saved in the hidden partition D 755 760A01 Series User Manual 755A01 032604 p65 96 2004 3 26 15 28

Statement: Symbol description: More information: Version

Contents

Download Pdf Manuals

Related Search

Related Contents