User Manual - Yacht Watchman
Contents
1. carried out via voice call such as naming the device etc see SMS Commands Powering the SentinelPoint The SentinelPoint can easily be switched off by the sms command pwdown Take a look at page 7 to get a description of the parameter To switch off the device remove the external power supply and send the sms command pwdown The LED will flash three times to indicate that the SentinelPoint will now be switched off To switch on the device connect the external power supply The LED will flash three times to indicate that the SentinelPoint is switched on Note Due to the internal design of the SentinelPoint it is only possible to switch off the device if no external power is applied Otherwise you cannot switch off the SentinelPoint Note It is possible that the internal battery of the SentinelPoint becomes fully discharged if the device is switched off for a long time 25 days If you now connect the SentinelPoint to the power supply the device enters a special charging mode to charge the battery During this phase GSM and GPS is totally switched off and the LED will repetitively blink four times The SentinelPoint automatically enters normal operating mode if the internal battery has reached a charge threshold level In order to enter normal operation mode it typically takes 30 60 minutes charging time depending on the temperature of the internal battery and the external power supply SMS Commands The device is2. the set radius it sends a MOVE OUT alarm to the user defined master numbers If SentinelPoint moves back within 15 meters from the home position then the SentinelPoint sends a MOVE IN alarm to the master numbers HOME Set the current position as home position if the MOVE ALARM is enabled NAME Command to set the name of Sentinel Point This name will be sent in each sms Default MY SP max 12 characters TRACKING Command to activate or deactivate the SMS tracking function Note if enabled Every 5 minutes a status SMS would be sent to every specified Master Note A status report will be sent with the following meanings TRACKING ON OFF BATT Command to set the type of battery either to 12V or to 24V 12 24 Note for BATT set to 12 or 24 The parameter sms will show the parameter BATTERY V with the actual battery voltage NEWPWD Command to change the default password for SMS commands NEWPWD must be followed by the 4 digits password you wish to set Example NEWPWD 1111 NOTE Don t forget the password There is currently no way the user can set it back to default If you do forget the password please contact the supplier who will reset the password remotely PWDOWN Command to shut down SentinelPoint Note Before SentinelPoint can be shut down it has to be disconnected from the external power supply SMS Examples To request a status SMS send the following text to th
3. 2 MASTER3 Master number 3 an alarm SMS will sent to this number gt MASTER3 MOVEALARM ON Indicates that the move alarm is enabled gt MOVEALARM ON OFF ALARMS OFF Indicates that alarms are disabled gt ALARMS ON OFF BATT 12 12V battery type used gt BATT 12 24 Status SMS The status SMS contains the current status of the device The SMS will send from the device to the originator of a received SMS when the originator is asking for it by the keyword status SMS from the originator to the SentinelPoint 4444 status SMS from the SentinelPoint to the originator Sentinel Point MY SP FW 20120405 LAT LONG 52 10723 8 66492 HOME POS 52 10727 8 66503 BATTERY 12 8V TRACKING OFF SMS text description SentinelPoint Device logo MY SP Name of the SentinelPoint FW 20120405 Firmware version LAT LONG 52 10723 8 66492 Current latitude and longitude HOME POS 52 10727 8 66503 Latitude and longitude of your home position BATTERY 12 8V Current voltage of the external battery TRACKING OFF SMS tracking function is disabled ALARMS ON Current State of Alarms 10 Alarm SMS The alarm SMS will automatically send by the device to the numbers at Master1 Master2 and Master3 Alarm SMS from the SentinelPoint to the Masters oa Alarm source gt SentinelPoint MY SP FW 20120405 LAT LONG 52 10723 8 66492 HOME POS 52 10727 8 66503 BATT
4. BATTERY 12 8V SPBATTERY 3 9V ALARMS OFF TRACKING ON SMS text description TRACKING SMS indicates the type of alarm see next table SentinelPoint Device Logo MY SP Name of the SentinelPoint GPSFIX YES YES if the device can receive the GPS position otherwise NO LAT LONG 52 10723 8 66492 Current latitude and longitude HOME POS 52 10727 8 66503 Latitude and longitude of your home position SOG 0 Speed Over Ground in knots C0G 183 Course Over Ground BATTERY 12 8v Current Voltage of the External Battery SPBATTERY 3 9 Current voltage of the device internal battery ALARMS OFF Indicates alarms are currently disabled TRACKING ON Indicates TRACKING is currently enabled 12 LED flashing codes The SentinelPoint uses different flashing codes of the LED to indicate the current condition of the GSM module LED GSM GPS 1x green SentinelPoint is registered GPS position is acquired logged in and ready to use 2 x green SentinelPoint is registered GPS position is not logged in and ready to use acquired 3 x green SentinelPoint is not registered A GPS position is not into the GSM network acquired 4 x green SentinelPoint is in Charge GPS and GSM are disabled mode in this mode fast flashing The SentinelPoint is receiving or transmitting a SMS or The SentinelPoint is receiving an incoming call V
5. ERY 12 8V TRACKING OFF SMS text description Alarm source gt indicates the type of alarm see next table SentinelPoint Device Logo MY SP Name of the SentinelPoint FW 20120405 Firmware version LAT LONG 52 10723 8 66492 Current latitude and longitude HOME POS 52 10727 8 66503 Latitude and longitude of your home position BATTERY 12 8V Current voltage of the external battery TRACKING OFF SMS tracking function is disabled ALARMS ON Current State of Alarms Alarm source gt description MOVE OUT Indicates that device is moved out of the set GPS position MOVE IN Indicates that device is moved in the set GPS position BATT ALARM 0888in dicates that the external voltage is under the set limit DISCON ALARM Indicates that no external voltage is connected 11 Tracking SMS The tracking sms will automatically be sent every 5 minutes by the device if the tracking mode was previously enabled with the sms instruction tracking on take a look at page 10 to get a description of the parameter Note The tracking sms will be sent to the set masters MASTER1 MASTER2 MASTER3 The device will try to resend the SMS to the recipient every 30 seconds until successful Alarm SMS from the SentinelPoint to the Masters TRACKING SMS SentinelPoint MY SP GPSFIX YES LAT LONG 52 10723 8 66492 HOME POS 52 10727 8 66503 SOG 0 COG 183
6. If new goods develop a defect during the 12 month Warranty period please contact us and we will advise the returns procedure Please note that the warranty does not cover you for any defects in the goods arising from fair wear and tear willful damage accident negligence by you or any third party use otherwise than in accordance with its intended use failure to follow the manufacturer s or Supplier s instructions or any alteration or repair carried out without the Intelligent Devices Limited s prior written approval About SentinelPoint SentinelPoint is an alarm and tracking device for fixed installation in all types of vehicles or machinery The device includes a GPS receiver with integrated patch antenna as well as a GSM wireless module It is possible to use appropriate alarm settings for situations where a variable local area is left or whilst power interruption SentinelPoint is designed for fixed and permanent installation to a 12V or 24V power supply However the device also features a built in LilO battery so that theft sabotage or unintentional power failures can be signaled Alarms communicated via SMS and to up to three phone numbers can be user defined to receive these alarms Device settings are also possible via voice calls The caller is lead through a voice menu and can set the requested parameters using the mobile keypad Access Security SentinelPoint Password This password is assigned to the SentinelPoint and i
7. Search FlyTo Find Businesses Directions Fly to e g Hotels near JFK 50 50 5528N 001 06 0977W W Q M 50 50 5528N 001 06 0977W x Y Places Add Content v 5 My Places gt Sightseeing 0 Select this folder and click on the Play button below to start V Sentinel1 YE Sentinel4 2 AR Cantinal Y Layers v Primary Database y gt Y Geographic Web f IMPORTANT When entering geographic co ordinates into Google Earth or Google Maps in this case 50 and 001 a space must be entered between the values for latitude and longitude Entries for latitude and longitude must also be separated by a comma 14
8. SentinelPoint User Manual Firmware release 20120710 YACHT WATCHMAN ERNATIONAL INC 2340 SW Palm City Road Stuart FL 34994 Phone 800 805 2822 Fax 772 872 5227 www yachtwatchman com Contents A A A a a 3 A a ean arate este Error Bookmark not defined sentinel Pont PassWord ia 3 Technical SPECIAL ea riot ache eter niet arenas 4 General A te cera E ARN er 4 RG WB ces chain opa 4 DPSS cesses esse cured eae ens cise cut ut ate estat cate caste near ea eed ee anaes 4 POWED OUD Vici nrant Ook ttenen li 4 CULFENECONSUM DUO acuario 4 Installation aan SE A A 5 et ME O E O feces dese EI 5 Powering the Sentinel Point caes A 6 SMS COMM ands S eee 7 SIA Examples AA A O E EE EE 8 F rameter MS id 9 Status MS amt a een er eT Er ee ete a 10 A O A E A 11 LED flashing COMES o A se 13 VOS a a a e Cir nny Ser eae 13 Ma AA A A ENEE 13 Preparing the GPS Coordinates for GoogleEarth 0 ceseeseessessestesseseeteseeteeseetenteeeneeseenss 14 Terms amp Conditi ns o 15 Disclaimer Please be aware that the use of SentinelPoint is at the users own risk Please see the Intelligent Devices Limited website for terms and conditions and the accompanying terms and conditions incorporated in the User Manual Warranty All new goods supplied by SentinelPoint have a 12 months warranty period from the date the goods were delivered unless otherwise stated This warranty does not affect your statutory rights as a consumer
9. e SentinelPoint 4444 status To request a parameter SMS send the following text to the SentinelPoint 4444 parameter To set the numbers Master1 and Master2 and request a parameter SMS to check the numbers send the following text to the SentinelPoint 4444 parameter Master1 1xxxxxxxxxx Master2 1xXxxxxxxxxx To enable alarms send the following text to the SentinelPoint 4444 parameter alarms on To set the home position send the following text to the SentinelPoint 4444 home To change the password for sms commands to 1111 send the following text to the SentinelPoint 4444 newpwd 1111 To enable the tracking function in an interval of 5 minutes send the following text to the SentinelPoint 4444 tracking on Parameter SMS The parameter SMS contains all settings for the device The SMS will send from the device to the originator of a received SMS when the originator is asking for it by the keyword parameter SMS from the originator the SentinelPoint 4444 parameter SMS from the SentinelPoint to the originator SENTINELPOINT MY SP MASTER1 44179123xxxx MASTER2 MASTER3 MOVEALARM ON ALARMS OFF BATT 12 SMS text description SentinelPoint Device logo MY SP Name of the SentinelPoint NAME MASTER1 0123456789 Master number 1 an alarm SMS will sent to this number gt MASTER1 MASTER2 Master number 2 an alarm SMS will sent to this number gt MASTER
10. fully configurable by SMS commands The following table shows each command with a short description The allowed values ranges is given in brackets The next pages shows some examples of how to use this commands SMS command description PARAMETER Request for a parameter SMS The Device will send a parameter SMS to the originator STATUS Request for a status SMS The Device will send a status SMS to the originator MASTER1 Command to set the number for Master1 Default NA is shown max 18 characters Use the International Numbering system when using country codes not 00 MASTER2 Command to set the number for Master1 Default NA is shown max 18 characters MASTER3 Command to set the number for Master1 Default NA is shown max 18 characters ALARMS Command to enabled or disable the alarms ON OFF Note if enabled An alarm sms with the alarm cause will be sent if the external battery has been disconnected or there is no battery voltage or the external battery charge is low Note A parameter report will be sent with the following meanings ALARMS ON OFF MOVEALARM Command to enable or disable the move alarm YES NO Note By enabling the move alarm the current position will be saved as home position if there isn t already a home position set The allowed movement of the SentinelPoint around the home position is 75m If the SentinelPoint moves out
11. oice Call The SentinelPoint can be controlled by authorized callers with held of a voice call A caller is authorized if the caller can identify himself with a correct access code i e after the answers incoming call the caller must enter the correct 4 figure access code figures only via the phone keyboard Operation The SentinelPoint can be controlled from any telephone mobile phone that is able to transmit DTMF Dual Tone Multi Frequency tones The SentinelPoint answers the call after the 2nd ring A female voice then asks the caller to enter the password If this does not occur within 20 seconds every input resets the call time back to 20 seconds or an incorrect password is entered three times the connection will be terminated If the correct password is entered the SentinelPoint responds with an announcement that it is ready to receive commands A Voice Menu tells the caller how to navigate through it and how to set any changes NOTE If there is no input within 1 minute the connection will be closed automatically 13 Preparing the GPS Coordinates for Google Earth The information for latitude and longitude can be entered directly into Google Earth or Google Maps Example The SentinelPoint sends the position in the SMS LAT 50 50 5528N LONG 001 06 0977E An example for entering the co ordinates 50 50 5528N 001 06 0977E 50 latitude north and 1 longitude east in Google Earth Y
12. s required when settings of the SentinelPoint are made retrieved or need to be changed This password also consists of a 4 digit number and is set to 4444 in default mode It can be changed using the command NEWPWD See SMS Commands There is a master password that can be used in case the individual set password is forgotten Please contact your dealer in this case Technical Specification General GSM Casing measuring approx 8x 6x3 cm Determination transmitting of GPS coordinates Speed Determination transmitting of GSM cell Data Parameter configuration per SMS or Voice Call The current status is signaled via green LED Ambient temperature 0 50 C Storage temperature 10 70 C Integrated GSM module Telit GE865 Suitable for all networks frequencies GSM 850 E GSM 900 DCS 1800 PCS 1900 and all providers UMTS is not supported Usable with prepaid or contract SIM cards of all providers no SIM Lock Controlled via normal SMS acknowledgement MediaTek MT3329 receiver with excellent GPS performance 22 channel GPS receiver Internal patch antenna Power Supply The SentinelPoint needs a single power supply in the range of 12V 24V 600mA Current consumption The following table gives an overview about the average current consumption Average Current Description Up to 30mA at 12vDC All Functions Active Up to 25mA at 24vDC All Functions Active Between 50mA and 200mA In Ba
13. ttery Charge Mode Approx 0 5mA In pwdown Mode Approx 15mA With MOVEALARM 0FF Note The stated current consumption is an average current consumption Because of the internal battery charger the measured current can vary from the values in the table To measure the correct average current consumption it is necessary to measure the consumed current for a least 10 days to make sure that some complete charge and discharge periods are measured Note The stand by current for GSM and GPS depends on the used GSM provider and the environmental conditions Installation The SentinelPoint must be installed such that the build in GPS antenna is directed upwards There is an orange sticker that indicates the side that has to be uppermost No metal or metallized objects covers etc should be above the antenna Quick Start For a quick start of the SentinelPoint three steps are necessary 1 Insert your SIM card to the SentinelPoint Remove Lid Lift SIM Holder and slide SIM card in holder with cut edge top right then close SIM holder and slide holder forward to lock the SIM in 2 Connect the external power supply 12 24V Red gt positive black gt negative please observe the green LED refer to LED flashing Codes Now the SentinelPoint can be setup via SMS Commands e Set the name of the SentinelPoint e Set the master numbers for SMS Alerts e Choose the alarm types or some setting via Voice Call Note Some settings cannot be
Download Pdf Manuals
Related Search