Installation Instructions
Contents
1. Ethernet e Connectivity RJ45 auto crossover e Wire type 4 pair Cat 5e or better structured cable e Distance up to 100m e Speed 10 100BaseT half full duplex auto negotiation Coax e Distance up to 300m e Connectivity BNC RG 59 U or similar e Throughput is rated to pass 100mbps from camera to receiver With the proper headend equipment multiple Megapixel cameras can be used LED Indicators e Blue LED Coax link connection UL Listed Class 2 or limited power source NetWay1D eBridge4SK LED Indicators cont d e Green LED Power eBridge100SPR only e Yellow and Green LED RJ45 IP Link status 10 100Base T active Environmental e Operating Ambient Temperature eBridge100SPR 40 C to 60 C 40 F to 140 F eBridge4SPT 60W 40 C to 75 C 40 F to 167 F e Storage Temperature 40 C to 75 C 40 F to 167 F e Humidity 20 to 85 non condensing Applications e Retrofit digital IP cameras in an analog CCTV installation up to four 4 IP cameras expansion per analog camera e Works with Megapixel HD720 HD1080 and VGA SD cameras see note pg 2 e Extend Network link distance in an industrial environment e Upgrade deployed CCTV Coax to a digital network in Retail Hospitality Arenas Casinos Airports Schools Hospitals Transportation etc Mechanical e Dimensions H x W x D approx eBridgel00SPR 4 375 x 3 5 x 1 111 125mm x 88 89mm x 25 4mm eBridge4SPT 12. programming devices installed in one time zone and monitored in another Sync Setup Fig 3b pg 6 Clicking the button labeled Syne Date Time with computer will set the eBridge4SPT to the time of the host computer Port ID Fig 3c pg 6 Enter a descriptive name and or location of the device connected to the port Port Status Fig 3d pg 6 Individual ports can be enabled or disabled by clicking the button labeled Enable Port Disable Port This feature allows unused ports to be disabled and also can be used to reboot a connected device by cycling power OFF and ON After all fields have been programmed click on the button labeled Save Settings Fig 3 M Altronix eBr idge Management Interface LINC Status Setup Network Settings Security Settings Events Log v1 99 22 eBridge4SPT Setup ao rap recever soares A BE mg eA eA EA eA e eBridge4SK Security Settings Click on the tab labeled Security Settings The eBridge4SPT security setting page will open In this screen the SSL certificate and Key will be entered the SSL can be enabled or disabled and new username and password can be set Using an SSL certificate will ensure that when remotely accessing the eBridge4SPT all data has been encrypted and there for secure through the assigned HTPPS Port Fig 4a SSL Certificate Setting Fig 4a pg 7 Generating a self signed SSL Certificate and Key 1 State Two letter code representing the state where t
3. 1 32 kg Shipping 3 9 Ibs 1 77 kg Input power requirements Environmental Conditions Weights approx 2 eBridge4Sk Typical Application Fig 1 eBridge100SPR eBridge4SPT Front View eBridge PLUS PoE output p amar TT TOY i Ethernet Switch OC Coax up to 300m 4 Altronix CAT 5e CAT 5e up to 100m h m lt t NVR Network Video Server U PoE PoE Head End salen e Cameras Equipment Maximum Length of Coax Type vs Camera Power PoE Class c P RG59 U RG59 U RG59 U RG59 U RG6 U e 23AWG 22AWG 20AWG 18AWG 18AWG Max Length meters 13W 0 or 13W 3 260 64m 335 28m 500m 500m 500m 25W 118 9m 150 6m 239 3m 365 8m 365 8m 60W 50 3m 63 4m 100 6m 160m 160m 90W 33 5m 42 1m 67 1m 106 4m 106 4m 120W 25m 31 7m 50 3m 80 2m 80 2m Internet Browser Setup Factory Default settings e IP Address 192 168 168 168 e User Name admin e Password admin 1 Set the static IP address for the laptop to be used for programming to the same network IP address as the eBridge4SPT i e 192 168 168 200 the default address of the eBridge4SPT is 192 168 168 168 2
4. 7 x 5 23 x 8 93 43 18mm x 132 84mm x 226 82mm Installation Instructions Wiring methods shall be in accordance with the National Electrical Code NFPA 70 ANSI and with all local codes and authorities having jurisdiction Wiring should be UL Listed and or Recognized wire suitable for the application eBridge100SPR and eBridge4SPT is not intended to be connected to outside plant leads and should be installed indoors within the protected premises The eBridge100SPR and eBridge4SPT is intended for indoor use only 1 eBridge100SPR installation a Secure unit to desired mounting surface with a proper fastening device utilizing the unit s mounting hole Unit should be mounted in proximity to Ethernet switch network NVR or video server b Connect 56VDC UL Listed Class 2 or limited power source to terminals marked Power Input observe proper polarity Fig 1 pg 3 Use 22AWG 16AWG wire for this connection Caution 56VDC will be present on coax The other end of the coax should only be connected to the eBridge4SPT c Connect structured cable from Ethernet switch NVR network video server to RJ45 jack marked 10 100 BaseT Fig 1 pg 3 d Connect Coax cable to BNC connector marked Coax Fig 1 pg 3 2 eBridge4SPT installation a Affix rubber pads to eBridge4SPT for shelf installation Fig 9 pg 12 b Connect Coax cable from eBridge100SPR to BNC connector marked Coax located on the back of the unit Fig 1 pg 3 c Con
5. Connect one end of the network cable to the network jack on the eBridge100SPR and the other to the network connection of the laptop eBridge4SK 3 Open a browser on the computer and enter 192 168 168 168 into the address bar A dialog box Authentication Required will appear requesting both user name and password enter the default values here Click on the button labeled Log In 4 The status page of the eBridge4SPT will appear This page displays the real time status and health of each device connected to the eBridge4SPT Network Setup Click on the tab labeled Network Settings This will open the Network Setting screen In this screen the MAC Address of the eBridge4SPT module will be found along with the programming fields for the Network Settings Trap Receiver Settings SNMP Port Settings and Email Settings Network Settings In the IP Address Method field select the method that the IP Address for the eBridge4SPT will be obtained Static or DHCP then follow the appropriate steps Fig 2 STATIC Fig 2a pg 4 1 IP Address Enter the IP address assigned to the eBridge4SPT by the network N eBr idge Management Interface LING administrator 2 Subnet Mask Enter ihe Subnet otihe network Z Setup Network Settings Security Settings Events Log 922 eBridge4SPT Network Settings 3 Gateway Enter the TCP IP gateway of the network access point router being used Note Gateway configuration is required to
6. D Trap Receiver IP Address 2 10 0 0 56 Outgoing Email 4 Outgoing Email 5 scott jrsport com maria jrsport com Cest Email Restore Default Submit Email Settings Trap Receiver IP Address 3 62 19 75 80 New network settings will take effect after the server is rebooted Click OK Trap Receiver IP Address 4 45 165 245 146 Restore Factory Settings Trap Receiver IP Address 5 50 74 175 125 Submit Trap Receiver IP Settings DHCP Fig 2a pg 4 1 After selecting DHCP in the IP Address Method field click the button labeled Submit Network Settings A dialog box will display New network settings will take effect after the server is rebooted Click OK Next click on the button labeled Reboot Server After rebooting the eBridge4SPT will be set in the DHCP mode The IP address will be assigned by the router when the eBridge4SPT is connected to the network It is recommended to have the assigned IP Address reserved to ensure continued access see the network administrator 2 Subnet Mask When operating in DHCP the router will assign the subnet mask values 3 Gateway TCP IP gateway of the network access point router being used will be displayed Reboot Server SNMP Port Settings SNMP Port 161 Trap Message Port 162 Submit Port Settings 4 eBridge4Sk 4 HTTP Port Ente
7. N ebr idge Installation Guide ner 0 2519 PLUS Ou eBridge100SPR EoC Receiver eBridge4SPT 4 Port PoE PoE EoC Transceiver Switch LISTED I T E 43KC Overview The eBridge4SK kit consists of eBridgel100SPR and eBridge4SPT which are Coax to CAT 5 Ethernet adapters media converters that deliver data and power over coax cable eBridge4SK enables fast 10 100 Base T Ethernet digital communication eBridge4SPT allows you to upgrade your existing infrastructure by replacing a single analog device with up to four 4 PoE PoE devices eBridgel00SPR passes data and sends power over the coax to the eBridge4SPT Data transmission and power over the Coax are possible up to 300m Maximum range from head end to the PoE camera device is 610m taking into consideration that up to 100m of structured cable may be deployed at each end Built in IP management allows for remote camera reset monitoring and reporting via various IP protocols eBridge4SK enables cost effective system upgrades and eliminates the costs and labor associated with installing new network cabling Note Ethernet maximum distance see Maximum Length of Coax Type vs Camera Power PoE Class pg 3 Features Agency Listings e UL CUL Listed for Information Technology Equipment UL 60950 1 e CE approved Input e eBridgel00SPR 51 56VDC 60W max power eBridge4SPT powered by eBridge100SPR Power Output e eBridge4SPT 4 ports PoE 30W per port e Total output power 60W
8. Settings Jul 31 2015 08 05 03 GMT 0400 Eastern Daylight Time Jul 31 2015 08 10 12 GMT 0400 Eastern Daylight Time Jul 31 2015 08 15 24 GMT 0400 Eastern Daylight Time Jul 31 2015 08 20 36 GMT 0400 Eastern Daylight Time Jul 31 2015 08 35 17 GMT 0400 Eastern Daylight Time Jul 31 2015 08 40 28 GMT 0400 Eastern Daylight Time Jul 31 2015 08 45 43 GMT 0400 Eastern Daylight Time Jul 31 2015 08 50 00 GMT 0400 Eastern Daylight Time Friday Jul 31 2015 9 01 am Last update Fri Jul 31 2015 09 01 37 GMT 0400 Eastern Daylight Time eBridge4SPT eBridge4SPT Port3 eBridge4SPT eBridge4SPT Port1 eBridge4SPT eBridge4SPT Port2 eBridge4SPT eBridge4SPT Port4 eBridge4SPT eBridge4SPT Port3 eBridge4SPT eBridge4SPT Port1 eBridge4SPT eBridge4SPT Port2 eBridge4SPT eBridge4SPT Port4 Disabled Disabled Disabled Disabled Enabled Enabled Enabled Enabled eBridge4Sk Heartbeat Timer The heartbeat timer will send a trap message indicating that the eBridge4SPT is still connected and communicating Setting the Heart Beat Timer 1 Click the button labeled Heartbeat Timer Setting 2 Select the desired time between heartbeat messaging in the Days Hours Minutes and Seconds in corresponding fields 3 Click the button labeled Submit to save settings Fig 6 M Altronix eBr idge Management Interface LINC Status Setup Network Settings Security Settings Events L
9. der and network fields have already been populated 2 Outgoing Email Address 1 5 Enter up to five outgoing email addresses 3 Click the button labeled Submit Email Settings Email settings will be saved To test the email setup click the button labeled Test Email An email will be sent to all Outgoing email addresses If the test email is not received contact the Em PSADWRWNE PAONIAMNKRWNE eBridge4SK 5 network administrator and repeat the email setup sets After all fields have been programed click the button labeled Reboot Server A dialog box will display Please allow up to 30 sec for server to reboot Click OK All programmed information will be saved after the server has rebooted Setup Click on the tab labeled Setup The eBridge4SPT setup page will open In this screen the Site ID Date Time and Port identification are setup along with the ability to enable and disable individual ports Site ID Fig 3a pg 6 Enter a descriptive name that will identify the location of the eBridge4SPT The Site ID will appear in both the trap message and email notifications Date Time Fig 3b pg 6 Time and Date can be entered two different ways manually or by syncing the date and time with the host computer Manual setup Fig 3b pg 6 Individually select the appropriate information for each of the required field then click Update This will update time of the eBridge4SPT to the programmed information The manual setup can be used when
10. e server is rebooted Click OK Email Settings Fig 2d pg 4 The eBridge4SPT can send emails via an in house email server email service provider i e Gmail Yahoo or Altronix default email service In house email server From Enter the email address assigned to the eBridge4SPT module by the system administrator Subject Identify the location of the ebridge4SPT i e the Site ID Username Enter the username associated with the eBridge4SPT module email address Password Enter the username password SMTP server IP Enter the SMPT IP address of the in house email server SMTP server Port Enter the SMPT port assigned to the in house email server Outgoing Email Address 1 5 Enter up to five outgoing email addresses Click the button labeled Submit Email Settings email setting will be saved il service provider From Enter the email address for the eBridge4SPT module Subject Identify the location of the eBridge4SPT 1 e the Site ID Username Enter the username associated with the eBridge4SPT module email address Password Enter the username password SMTP server IP Enter the SMPT IP address of the email service provider SMTP server Port Enter the email SMPT port number The default SMPT email ports are 25 or 465 unless otherwise specified Outgoing Email Address 1 5 Enter up to five outgoing email addresses Click the button labeled Submit Email Settings email setting will be saved Altronix default email service 1 All required sen
11. ficate Status Certificate OK Valid SSL Certificate Bad Certificate Invalid SSL Certificate No Certificate a Valid SSL Certificate has not been loaded Key Status Key OK Valid SSL Key pee Bad Key Invalid SSL Key No Key a Valid SSL Key has not been loaded SSL State The SSL of the eBridge4SPT can be turned on and off by click the button labeled Turn SSL On Turn SSL Off Key Status Key Ok eBridge4SK 7 Change Username and Password Fig 4c pg 8 1 Username Enter the new Username up to 32 characters required to access the eBridge4SPT 2 Password Enter the new Password up to 32 alpha numeric characters required to access the eBridge4SPT 3 Confirm Password Reenter the new Password Click the button labeled Save Username and Password A dialog box with appear New settings have been applied Click OK After saving the new username and password will be active Event Log and Heartbeat Timer Click on the tab labeled Event Log The eBridge4SPT event log will open This screen will display the event log along with the heartbeat timer setup Fig 4c Change Username and Password Username RJsports Password Confirm Password Save Username and Password Event Log The event log will display the 50 most recent events To update the Event Log click the button labeled Display Refresh Log Fig 5 Events Log Site ID RJ Sports Wear Display Refresh Log Heartbeat Timer
12. he organization is located State NY 2 Location The city where the organization is located 3 Organization The legal name of the organization This should not be abbreviated Locality Brooklyn and should include suffixes such as Inc Corp or LLC 4 Unit Name Name of the device Organization RJ Sports Wear Inc 5 Common Name Domain name or IP address of the server This is typically assigned by the network administrator 6 Email Address An email address used to contact the organization After all field have been completed click on the button labeled Submit SSL Settings A dialog box SSL Certificate Settings Unit Name eBridge4SPT Common Name 192 168 168 168 will appear Please allow up to 30 secs for server to reboot Click OK A self signed SSL certificate Email Address will be generated with the information provided in the SSL certificate settings fields The certificate will be valid for 500 days and time stamped with the time settings present on the eBridge4SPT module The date and time must be synced with the host computer before generating an SSL certificate Using a private SSL certificate and Key Fig 4b pg 7 Private SSL Certificates and Keys must be uploaded using the Altronix Dashboard For additional information refer to the Altronix Dashboard setup user manual section Fig 4b Updating firmware SSL certificate and Key SSL Status SSL Status Certificate Status Certificate Ok Certi
13. n Status OK J 10 eBridge4Sk eBridge4SK Notes Ea ee eBridge4SPT Chassis Mechanical Drawing amp Dimensions H x W x D approx 1 7 x 5 23 x 8 93 43 18mm x 132 84mm x 226 82mm Fig 8 G 00 6 N g gQ z R a E a M 0O m a st oo a l x lt O De S E Z a O 2 io Oo bY N co m lt ral Q U 1 ora Shelf Installation Fig 9 1 Position and affix rubber pads C included at each corner on the bottom of the unit Fig 9 2 Place unit in desired location sisi Mounting Hardware included amp Four 4 rubber pads we Rubber Feet Altronix is not responsible for any typographical errors 140 58th Street Brooklyn New York 11220 USA 718 567 8181 fax 718 567 9056 website www altronix com e mail info altronix com Lifetime Warranty Made in U S A IleBridge4SK 2 1250 a oobi eE L Lal m MEMBE eBridge4SK
14. nect structured cable from PoE PoE cameras devices to RJ45 jacks marked 1 4 Fig 1 pg 3 Note The eBridge is designed to accommodate Megapixel HD720 HD1080 and VGA SD cameras It is important to note that some high resolution and high frame rate cameras may demand faster headend processing ability such as a PC graphics card to present a quality image If the headend processing equipment is insufficient in speed the image may show pixelation and latency It is advisable to pretest system if unsure Alternatively frame rate and resolution may be reduced to accommodate system equipment Technical Specifications Parameter Description Connections BNC for Coax link RJ45 for Ethernet link eBridgel00SPR 51 56VDC 60W max power eBridge4SPT powered by eBridge100SPR Blue Coax Link Indicators Yellow RJ45 connector On Link Off No Link Blinking Activity Green RJ45 connector On 100Base TX Off 10Base T Operating Ambient Temperature UL60950 1 eBridgel00SPR 40 C to 60 C 40 F to 140 F eBridge4SPT 60W 40 C to 75 C 40 F to 167 F Relative humidity 85 5 Storage Temperature 40 C to 75 C 40 F to 167 F Operating Altitude 1000 to 6 561 679 ft 304 8 to 2000m Regulatory Compliance UL CUL Listed for Information Technology Equipment UL 60950 1 CE approved eBridge100SPR Product 5 1 oz 0 144 kg Shipping 7 76 oz 0 22 kg eBridge4SPT Product 2 9 Ibs
15. og v1 99 22 Events Log Site ID RJ Sports Wear Friday Jul 31 2015 9 01 am Display Refresh Log Heartbeat Timer Settings Last update Fri Jul 31 2015 09 01 37 GMT 0400 Eastern Daylight Time Heartbeat Timer Settings Days Hours Minutes Seconds Updating Firmware Firmware updates must be done using the Altronix Dashboard For additional information refer to the Altronix Dashboard setup user manual s section Updating firmware SSL certificate and Key eBridge4SK Status Screen a Class Power Watts Fig 7a pg 10 Wattage required by the PoE class of the device b Actual Power Draw Watts Fig 7b pg 10 Amount of watts being drawn by the connected device c Device Status Fig 7c pg 10 Active or Inactive d Port Status Fig 7d pg 10 Indicates whether port is Enabled or Disabled Fig 7 a M Altronix ebr idge Management Interface LINC Status Setup Network Settings Security Settings Events Log v1 99 22 eBridge4SPT Status Site ID RJ Sports Wear Wednesday Jul 15 2015 9 35 am Port 1 Main Entrance Port 2 Production cew P caine Watts Draw Class Power Actual Power Draw Device Status Port Status Watts Watts Device Status Port Status Oco O On Oe Enabed Port 3 Receiving Port 4 Shipping Class Power Actual Power Draw Class Power Actual Power Draw Watts Watts Device Status Port Status Watts Watts Device Status Port Status Connectio
16. properly receive emails from the device 4 HTTP Port Enter the HTTP port number assigned to the eBridge4SPT module by the network administrator to allow remote access and monitoring The default inbound port setting is 80 HTTP is not encrypted and unsecure Even though HTTP can be used for remote access it is recommended primarily for use with LAN connections 5 HTTPS Port Enter the HTTPS port number assigned to the eBridge4SPT module by the network administrator to allow remote access and monitoring Site ID RJ Sports Wear Site ID RJ Sports Wear Jevent report linginfo com Subject Network Settings Email Settings IP Address Method STATIC From i IP Address 10 0 0 113 Subnet Mask 255 255 255 0 Username event report Gateway 10 0 0 1 Password esesesse Password HTTP Port 2713 SMTP Server smtp gmail com HTTPS Port 443 SMTP Server Port 587 MAC Address BC 34 00 30 00 B3 Submit Network Settings Outgoing Email 1 mike jrsport com Outgoing Email 2 steve jrsport com Trap Receiver Settings Outgoing Email 3 amy jrsport com The default inbound port setting is 443 Being encrypted and more secure HTTPS is highly recommended for remote access Click the button labeled Submit Network Settings A dialog box will display Trap Receiver IP Address 1 10 0 0 102
17. r the HTTP port number assigned to the eBridge4SPT module by the network administrator to allow remote access and monitoring The default inbound port setting is 80 HTTP is not encrypted and unsecure Even though HTTP can be used for remote access it is recommended primarily for use with LAN connections 5 HTTPS Port Enter the HTTPS port number assigned to the eBridge4SPT module by the network administrator to allow remote access and monitoring The default inbound port setting is 443 Being encrypted and more secure HTTPS is highly recommended for remote access 6 Click the button labeled Submit Network Settings A dialog box will display New network settings will take effect after the server is rebooted Click OK Trap Receiver Settings Fig 2b pg 4 1 Enter up to five SNMP trap receiver IP addresses When accessing the eBridge4SPT remotely check with the network administrator for proper configuration 2 Click the button labeled Submit Trap Receiver IP Settings A dialog box will display New Trap Receiver IP settings will take effect after the server is rebooted Click OK SNMP Port Settings Fig 2c pg 4 SNMP uses the default port 161 for general SNMP messages and port 162 for SNMP trap messages In the event these port need to be changed enter the new port numbers assigned by the network administrator Click the button labeled Submit Port Settings A dialog box will display New SNMP port settings will take effect after th
Download Pdf Manuals
Related Search