Attila User Manual
Contents
1. Cs CS N k NU W KS 1 Extend the sprayer and securely connect the feed tube 1 to the flow valve 2 Connect the male 3 pole connector 2 from the lance to the tank female 3 pole connector 5 and lock the both connector 3 Remove the atomiser protective cover 4 and check by hand that the atomiser disc spins freely 4 Turn on the switch 3 STEP BY STEP FAULT FINDING PROCEDURE Motor Not Functioning Battery terminal is not inline with the sprayer s terminal Faulty battery or carbon formed on the terminals Loose connection of battery or switch terminal System short circuit Electric motor of the pump has decayed 6 Charging was done correctly Switch Q should be in ON position when charging 3 pole connector is connected properly 1 2 3 4 5 Motor Functioning But Not Spraying As Desired Nozzle is blocked Disc is blocked Hose is blocked Rane cases Motor has worn out NN NN NN Fr 1 2 3 4 Tank Is Leaking At The Side 1 Valve STMC 021 10045 is broken 2 Washer STTK 012 10019 has worn out or missing 3 Hose clip is loose or broken METHODS OF USE For more detailed information on preparation and use of sprayers refer to the manual supplied with the CDA sprayer Pre mix the herbicide product in the required volume of water in the 10 litre backpack see section below on mixing and calibration and attach the backpack to the sprayer Hold the sprayer at an a2. Attila Cda C w Batt Conver Kit Battery Case Hose 1 0 2 Switch Battery Housing Battery Housing Cover N Tank Cock Battery Housing Ring Nut Brass Screw 5ma x 30te Drawtube Connection Octagonal Cap Drawtube Ring Nut Drawtube Octagonal Cap To Stick Flange Brass Spacer O 5 Galvanized Wing Nut O 5 Stainless Steel Spring Float Dv Nozzle N 3 Electric Motor N And Support Motor Washer Nozze Flange N Atomizing Disk N Atomizing Disk Protection Helically Wound Wire With Faston Neck Strap th Nylon 80 Mesh Strainer Filling Cap Complete Spare Cup Cover Spare Cup 10 Liter Tank Battery Bottom Cover Battery Cover Bottom Screw Stand Guard Outlet Washer Outlet Valve Outlet Valve Nut Straps Stopper Shoulder Strap 40 STMC 021 10048A NEW Switch C W Switch Cover 41 STMC 021 10050 6V 3aH Lead Sealed Battery 42 STMC 021 10051A NEW 6V Battery Charger 43 STMC 021 10052A NEw Wire Harness From Battery 3 Pole Connector 44 STMC 021 10002A New Electric Wire Black Red 3 Pole Connector 45 STMC 021 100057 PVC Tube CDA PERIODIC INSPECTION CHECK LIST ITEM PARTS NO DESCRIPTION 4 MTH 6 MTH 8 MTH 12 MTH O O O d O OO CH O O O O OO O SO pn P w N STIC 031 10002 0 2 Switch STIC 031 10020 Float DV STIC 031 10023 Nozzle n 3 STIC 031 10024 Electic motor N and support 0 STIC 031 10025 Motor washer 0 STIC 031 10027 Atomizing disk N 0 STIC 031 10039 Helically wound wire with faston
3. CDA SPRAYER USER GUIDE PROTOCOL CDA SPRAYER C W FLOAT 10L TANK AND BATTERY CASE ABOUT CDA SPRAYER An electric sprayer that allows the fulfillment of optimal treatments with capacity of 10 litres This sprayer is manufactured in durable and impact resistant material It is chemical resistant an UV stabilized The sprayer has been designed using the very latest technology to give longevity and reliability The battery is rechargeable 6 volt 3 Ah S L A unit Sealed Lead Acid The power requirement of the motor is only 0 10A The charger is able to complete battery recharge in 8 hrs Test has shown that the drop in voltage and current is insignificant to cause he drop in motor speed even after continuous use of over as such giving a consistent spray distribution Benefits Reduction of waste Improved safety for the operator Reduction of the environmental risks Chemical saving Reduction of spraying time Reduction of application costs AN EFFECTIVE PRODUCT IS NOT ENOUGH THE PRODUCT ITSELF MUST BE CORRECTLY APPLIED PROTECTIVE CLOTHING When applying herbicides with the CDA sprayer the following items MUST be worn e Rubber gloves and boots e Long Sleeve shirt e Long Trousers e Eye goggles It is also recommended to wear e Disposable coverall OR an apron PREPARING FOR SPRAYING The sprayer is delivered in a collapsed form To assemble ready for spraying
4. STIC 031 10047 Neck strap TH STIC 031 10040 Wire harness battery to switch Apex STTK 011 10002 Shoulder strap STTK 021 10057 PVC Tube STTK 012 10016 Battery bottom cover STMC 021 10044 Battery cover bottom screw STMC 021 10050 6V 3AH Lead sealed battery 0 STMC 021 10002A New Electric Wire Black Red 3 Pole Conn STMC 021 10048A New Switch C W Switch Cover STMC 021 10025A new Wire Harness Battery 3 Pole Conn O Complusory change for continuous use at indicated intervals The rest change when necessary RB Spray Tech Sdn Bhd 627487 P Head Office No 44 Lorong Sanggul 1E Bandar Puteri Klang 41200 Klang Selangor Darul Ehsan Malaysia Tel 603 5162 5746 51625745 Fax 603 51615741 E mail rbspraytechQunifi my info rbspraytech com SE www rbspraytech com YOUR KEY TO SMART TECHNOLOGY
5. adequate distance to be kept from the surface to be treated 20cm Switch on the atomiser disc and then open the flow tap Liquid should be seen flowing down the hose pipe to the atomiser head With the lance held preferably to the side of the operator walk at a moderate pace around 54 meters in one minute This will treat a 1 2m wide strip and will cover an area of 65 meter square each minute When spraying has finished close the flow tap and then switch off the atomiser Raise the spray head up to an angle of 45 with the spray head uppermost and then open the tap flow valve to allow any remaining liquid in the hose pipe to flow back to the tank Close the tap flow valve For ease of transport the tank can be disconnected use the flow valve to isolate any liquid left in a backpack and the sprayer collapsed OFF the switch and disconnect the 3 pole connector MIXING AND CALIBRATION With the CDA sprayer herbicides are usually applied in around 25 litres of water per hectare To prepare the spray mix select the rate of product to be applied per hectare then add sufficient water to make up to the total application volume required Example for one hectare Glyphosate rate 3 litres Add water 7 litres Total volume 10 litres Note When applying herbicide products ALWAYS follow the label recommendations The following table can be used to select the correct feed nozzle Appendix 1 Total Spray Swath Width
6. Feed Flow Rate Walking Speed Volume M Nozzle ml min m sec 25 1 2 5 166 0 9 Some products when mixed in water can be slightly viscous and the actual flow rate through each nozzle may be necessary to use a larger feed nozzle Sprayer calibration should be checked regularity by measuring the actual flow rate This is done by removing the feed nozzle from the spray head and measuring the amount of spray liquid in a measuring cylinder over a period of 1 minute When measuring the flow rate hold the sprayer at the normal spraying angle NB Actual required flow rates can be calculated using the formula in Appendix 1 6 I5 eer e LTL SS CON WD UT SS W N TANK NEW MODEL 27 28 29 30 31 32 33 34 35 36 37 38 39 SPRAYER PARTS LISTING PARTS NO STIC 03 STIC 031 10000 STIC 031 10001 STIC 031 10002 STIC 031 10003 STIC 031 10004 STIC 031 10035 STIC 031 10008 STIC 031 10009 STIC 031 10011 STIC 031 10012 STIC 031 10013 STIC 031 10014 STIC 031 10015 STIC 031 10016 STIC 031 10017 STIC 031 10018 STIC 031 10019 STIC 031 10020 STIC 031 10023 STIC 031 10024 STIC 031 10025 STIC 031 10026 STIC 031 10027 STIC 031 10028 STIC 031 10039 STIC 031 10047 STMC 021 10054 STTK 011 10008 STMC 021 10041 STMC 021 10042 STMC 021 10043 STTK 012 10016 STMC 021 10044 STTK 012 10006 STTK 012 10019 STMC 021 10045 STMC 021 10046 STTK 01 1 10003 STTK 011 10002 BATTERY CONVERSION KIT DESCRIPTION
7. TY e If the CDA sprayer will not be use for a long time remove the battery and store it in a cool and dry place e Recharge battery every 3 months GENERAL PRECAUTIONS e Do not switch the sprayer on with disc cover not removed this may damage the serrated disc Fill the tank only through the tank filter in order to avoid blockage of the nozzles Avoid spillage e NEVER USE CLASS ONE PRODUCTS WITH CDA SPRAYERS Use only clean water without impurities Do not start spraying without fixing the tank cap firmly Distribute the chemical evenly keeping the nozzle at an adequate distance from the surface to be treated INSTRUCTION BEFORE USAGE Make sure that GREEN DIODE lights up with static this occurs when the battery is fully charged and switched to trickle charge e Check the FILTER and NOZZLE to make sure it is free from any blockage or sediments Make sure that all FILTERS O RING and NOZZLE is in place correctly and sufficiently tight to avoid leakage Always pour liquid into the tank through tank filter and avoid spillage on backrest Make sure tank cap is close properly Adjust straps to suit individual sprayer operators Wipe offany spillage on the tank surface IN FIELD USAGE e Never drag the sprayer on the ground or on weeds while transporting and when reloading the liquid e Avoid the disc hitting the ground or weeds while spraying this could also cause blockage to the nozzle and disc e An
8. ngle of between 30 40 to the ground with the atomiser head positioned about 20cm above the weed Soil age or soil surface In this position the atomiser head should be angle slightly forward to spray away from operator N B make sure the spray head is more that 60cm away from the operator avoid contamination MAINTENANCE AFTER USAGE The sprayer must be decontaminated inside and out with mild solution of detergent followed by complete FLUSHING with clean water and run pump to clean the systems as well e Do not attempt to flush into base compartment and hand lance if necessary just wipe them with a DAMP CLOTH e Remove nozzle and filters for individual cleaning e Store separately if the sprayer is not going to be used for several days Nozzle need to be replaced every 6 months based on usage and filters to be replaced when necessary RECHARGING THE BATTERY i Connect the battery charger male 6 3 pole connector to the tank female 3 pole connector 5 and lock the both connectors ii The tank s switch 3 should be in ON position 111 Connect the battery charger plug to the main electric power and switch on The Red static in charging and the green static done charging indicator will glow The battery will need to recharge for 8 hours iv After done with charging remove the battery charger 6 from the main electric power and disconnect the 3 pole connector PROLONGED INACTIVI
Download Pdf Manuals
Related Search