CUEPIX BLINDER WW4 User Manual ver 1
Contents
1. CUEPIX BLINDER WW4 User manual www elationlighting com 2014 ELATION PROFESSIONAL all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ELATION PROFESSIONAL logo and identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ELATION brands and product names are trademarks or registered trademarks of their respective companies ELATION PROFESSIONAL ana all affiliated companies hereby disclaim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indirect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe insufficient and negligent assembly installation rigging and operation of this product Elation Professional USA 6122 S Eastern Ave Los Angeles CA 90040 323 582 3322 323 832 9142 fax www elationlighting com info elationlighting com Elation Professional B V Junostraat 2 6468 EW Kerkrade Netherlands 3 45 546 85 66 31 45 546 85 96 fax2. 7 powerCON IN 8 3pin DMX IN 9 5pin DMX IN 10 RJ45 NET IN 11 RJ45 NET OUT 12 3pin DMX OUT 13 5pin DMX OUT 14 powerCON OUT 15 Safety Cable Rigging Point CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com FIXTURE INSTALLATION FLAMMABLE MATERIAL WARNING Keep fixture at least 5 0 ff 1 5m away from any flammable materials decorations pyrotechnics etc ELECTRICAL CONNECTIONS A qualified electrician should be used for all electrical connections and or installations IQ CAUTIONS For added protection mount the fixture in areas outside walking paths seating areas or in areas were unauthorized personnel might reach the fixture Ambient operating temperature range for this fixture is 5 F to 113 F 15 C to 45 C Do not use the fixture under or above this temperature Before mounting the fixture to any surface make sure the installation area can hold a minimum point load of 10 times the weight of the fixture 210 Ibs 95 kg Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing Rkm POWER LINKING Max number of units that can be power linked is 1 units 110V and 4 units 220V CLAMP MOUNTING The CUEPIX BLINDER WW4 provides an integrated yoke rigging bracket When mounting this fixture to truss be sure to secure an appropriately rated clam
3. 16 4 62 Beam Diameter T2 39 a8 158 601 197 100 Field Diameter 2 38 78 MEN 387 Photometrics lux fc lux fc lux fc lux fc lux fc ALL FULL ON 12 300 3 130 1 581 714 66 DIMENSIONAL DRAWINGS m 13 im 400mm 14 6im 6 9im 17 4in 441mm d eds Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 25 CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com OPTIONAL ACCESSORIES __ Adatonail Cable Lengths Avallabl 26 CUEPIX BLINDER WW4 User Manual Ver 1
4. America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service send the product only to the Elation Professional factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty Elation Professional will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in its original package No accessories should be shipped with the product If any accessories are shipped with the product Elation Professional shall have no liability what so ever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which Elation Professional concludes after insoection affects the reliability of the product if the product has been repaired or serviced by anyone other than the Elation Professional factory unless prior written authorization was issued to purchaser by Elation Professional if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintenance cleaning or periodic check up During the period specified abov
5. MMABLE MATERIALS close to the fixture while operating to prevent any fire hazard The fixture must be installed in a location with adequate ventilation at least 1 5 feet 5m from adjacent surfaces Be sure no air ventilation slots are blocked DO NOT attempt installation and or operation without knowledge how to do so DO NOT permit operation by persons who are not qualified to operate this type of fixture Most damages are the result of operations by nonprofessionals Consistent operational breaks may ensure the fixture will function properly for many years to come DO NOT shake fixture avoid brute force when installing and or operating fixture Always install the fixture with an appropriate safety cable When installing the fixture in a suspended environment always use mounting hardware that is no less than M10 x 25 mm also be sure the hardware is insert in the pre arranged screw holes in the bracket of the fixture Use the original packaging and materials to transport the fixture in for service DO NOT TOUCH the housing bare hand during its operation Turn OFF the power and allow approximately 15 minutes for the fixture to cool down before replacing or serving 8 CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com FIXTURE OVERVIEW 11 1 213 14 15 1 LCD Menu Control Display MODE ESC Button UP Button Aa O N DOWN Button ENTER Button oO co Fuse
6. OW 1 Speed00 99 Flash00 99 ban Speed amp Flash Adjustable 07 FLOW 2 Speed00 99 Flash00 99 lan speed amp Flash Adjustable 08 FLOW 3 Speed00 99 Flash00 99 slip Speed amp Flash Adjustable 09 FLOW 4 Speed00 99 Flash00 99 ae Speed amp Flash Adjustable 19 CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com FLIP SETTING select the desired starting COB module and chase direction from one of the following modes below via UP DOWN buttons and then press ENTER fo confirm 20 CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com DIMMING CURVES The DimCurve menu allows you to select one of the following preset dimming Curves Standard Stage TV Architectural Theatre or Default Select the desired mode via UP DOWN buttons and then press ENTER to confirm See diagram below for more details Dimmer 100 5S 50 ris T dow Ar m s Ramp Effect ot 0S Fade Time yol PV 45 Fade Time a A A A a ee a e on ao on io woe lt 3 DMX WORKSHOP alternative software option to configure network settings DMX Workshop is a fully featured network management analysis configuration and diagnostics tool for Art Net networks It can be used to configure the Ethernet network settings on this fixture remotely such as the IP Address Subnet Mask and the DMX Universe This software application is Windows XP and Windows compat
7. access the fixture s main menu Once in the main menu you can navigate through the different functions and access the sub menus with the UP and DOWN buttons Once you reach a field that requires adjusting press the ENTER button to activate that field and use the UP and DOWN buttons to adjust the field Pressing the ENTER button once more will confirm your setting You may exit the main menu at any time without making any adjustments by pressing the MODE button L NOTE the LCD Menu Control Display will shut OFF and lockout after 30 seconds of no use Press and hold the MODE button for 10 seconds to unlock the LCD display DMX MODE ADDR 1 CH INFORMATION DISPLAYED DURING INITIAL POWER ON When the fixture is initially powered ON the display shows the following information Software Update ELATION CUEPIX BLINDER Fixture Software Version Greater than or equal to 17 CUEPIX BLINDER WW4 User Manual Ver 1 ELATION www elationliagahtina com Que ik gen ELATION CUEPIX BLINDER WW4 SYSTEM MENU specifications are subject to change without any prior written notice MENU OPTIONS VALUES DESCRIPTION DMX MODE ADDR 001 512 set DMX Address ADDR xxx Set DMX Channel Mode CH xx SLAVE AUTO RUN l Set the number of times each internal macro will FQN 01 99 FON XX repeat before moving to the next macro 01 STATIC i 01 09 select Internal Program Macro see INTERNAL MACRO MENU 09 FLOW4 Die LI eae Se
8. ce of 3pin Spin XLR fixtures may be implemented in a 3pin XLR DMX line When inserting standard 5pin XLR connectors in to a 3pin line a cable adaptor must be used these adaptors are readily available at most electric stores The following chart details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion Conductor 3 Pin XLR Female Out 5 Pin XLR Male In Data Compliment signal Pin 2 Data True signal Pin 3 Not Used Pin4 DoNot Use Not Used pon Pin 5 Do Not Use 15 CUEPIX BLINDER WW4 User Manual Ver www elationlighting com DMX ADDRESSING All fixtures should be given a DMX starting address when using a DMX controller so the correct fixture resoonds to the correct control signal This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the back of the fixture You can set the same starting address for all fixtures or a group of fixtures or set different address for each individual fixture Be advised that setting all fixtures to the same DMX address will subsequently control all fixtures in the same fashion in other words changing the settings of one channel will affect all the fixtures simultaneously If you set each fixture to a different DMX address each unit will s
9. curred during shipping If the carton appears to be damaged carefully insoect your unit for damage and be sure all accessories necessary to operate the unit have arrived intact In the event damage has been found or parts are missing please contact our customer support team for further instructions Please do not return this unit to your dealer without first contacting Customer support at the number listed below Please do not discard the shipping carton in the trash Please recycle whenever possible BOX CONTENTS e 1 powerCON Cable e Manual amp Warranty Card 4 CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com CUSTOMER SUPPORT Elation Professionale provides a customer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www elationlighting com for any comments or suggestions For service related issue please contact Elation Professional ELATION SERVICE USA Monday Friday 8 00am to 5 00pm PST Voice 323 582 3322 Fax 323 832 9142 E mail support elationlighting com ELATION SERVICE EUROPE Monday Friday 08 30 to 17 00 CET Voice 31 45 546 85 30 Fax 31 45 546 85 96 E mail support elationlighting eu WARRANTY REGISTRATION The CUEPIX BLINDER WW4 carries a two year 730 days limited warranty Please fill out The enclosed warranty card to validate your purchase All returned s
10. e Elation Professional will replace defective paris at its expense and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of Elation Professional under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of Elation Professional All products covered by this warranty were manufactured after January 1 1990 and bare identifying marks to that effect E Elation Professional reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured F No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by Elation Professional in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall Elation Professional be liable for any loss or damage direct or consequent
11. equire a standard 3pin or Spin XLR connector for data input and data output see figure below If you are making your own cables be sure to use two conductor shielded digital DMX cable rated at 120 ohms this cable is designed for DMX transmission and may be purchased from your Elation dealer or at most professional lighting retailers Your cables should be made with a male and female XLR connector on either end of the cable Also remember that a DMX line must be daisy chained and cannot be split unless using an approved DMX splitter such as Elation s Opto Branch 4 Opto Branch 8 or DMX Branch 4 13 CUEPIX BLINDER WW4 User Manual Ver www elationlighting com DMX Output DMX Input DMX Output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket 5 Pin XLR Socket 5 Pin XLR Socket 1 Ground 1 Ground 2 Data 2 Data Aa 3 Data 3 Data 4 Open 5 Open Be sure to follow fhe above figure when making your own cables Do not use the ground lug on the XLR connector Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR outer casing Grounding the shield could cause a short circuit and erratic behavior DMX 512 CONTROLLER CONNECTION Connect the provided XLR cable to the female XLR output of your controller and the other side to the male XLR input of the CUEPIX BLINDER WW4 The diagram below illustrates a typical DMX 512 connection w
12. ervice items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper and included in the shipping container If the unit is under warranty you must provide a copy of your proof of purchase invoice Items returned without a R A number clearly marked on the outside of the package will be refused and returned at customer s expense You may obtain a R A number by contacting customer support IB IMPORTANT NOTICE There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty Damages resulting from modifications to this fixture and or the disregard of safety and general user instructions found in this user manual void the manufactures warranty and are not subject to any warranty claims and or repairs 5 CUEPIX BLINDER WW4 User Manual Ver 1 ELATION www elationliagahtina com Que 9 9 2 YEAR LIMITED WARRANTY A Elation Professional hereby warrants to the original purchaser Elation Professional products to be free of manufacturing defects in material and workmanship for a period of two years 730 days from the date of purchase This warranty shall be valid only if the product is purchased within the United States of
13. hen the fixture is in the 9 Channel Mode You can chain multiple panels together through serial linking The cable that should be used is two conductor shielded DMX cable with XLR input and output connectors Always be sure daisy chain your in and out data connections never split or Y your DMX connections unless you are using an approved DMX splitter such as Elation s Opto Branch 4 Opto Branch 8 or DMX Branch 4 DMX a N L Address 1 Address 10 Address 19 14 CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com DMX 512 CONNECTION WITH DMX TERMINATOR A DMX terminator should be used in all DMX lines especially in longer runs The use of a terminator may avoid erratic behavior in your DMX line A terminator is a 120 ohm 1 4 watt resistor that is connected between pins 2 and 3 of a male XLR connector DATA and DATA This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line Using a line terminator will decrease the possibilities of erratic behavior 120Q i Termination reduces signal errors and avoids signal transmission problems ll and interference It is always advisable to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX Nan and PIN 3 DMX of the last fixture 5pin XLR DMX CONNECTORS some manufactures use 5pin XLR connectors for DATA transmission in pla
14. ial arising out of the use of or inability to use this product G This warranty is the only written warranty applicable to Elation Professional Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published 6 CUEPIX BLINDER WW4 User Manual Ver 1 ELATION www elationliagahtina com Que 9 9 SAFETY INSTRUCTIONS The CUEPIX BLINDER WW4 is an extremely sophisticated piece of electronic equipment To guarantee a smooth operation it is important to follow the guidelines in this manual The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual This device falls under PROTECTION CLASS 1 It s essential this device be grounded properly Only qualified personnel should perform all electrical connections KEEP THIS FIXTURE AWAY FROM RAIN AND MOISTURE UNPLUG POWER BEFORE SERVICING FIXTURE NEVER TOUCH FIXTURE DURING OPERATION AS IT MAY BE HOT NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE SENSITIVE PERSONS MAY SUFFER AN EPILETIC SHOCK e For proper operation follow the Installation guidelines described in this manual Only qualified and certified personnel should perform installation of this fixture and only the original rigging parts brackets included with this fixture should be used for installation Any modifications will void the or
15. ible and is free of charge and available via download here See link below http artisticlicence com index ophp mode products amp sub overviewkaction product id 351 2 CUEPIX BLINDER WW4 User Manual Ver 1 ELATION www elationliagahtina com QF 9 9 DMX CHANNEL FUNCTIONS AND VALUES ELATION CUEPIX BLINDER WW4 DMX Channel Values Functions 9 DMX Channels Specifications are subject to change without any prior written notice Control of 4 COB Modules chase direction depends on the Flip setting acu 2cu acu scn 7GH oa E ALL a COB MODULES DLL es COB 1 MODULE DIMMER ee eo Intensity O to 100 en COB 3 MODULE DIMMER EE eo Intensity O to 100 Intensity O to 100 OO ES ira Macros s enn MACRO SPEED 0 255 MACRO Program Speed SLOW to FAST ann MASTER DIMMER 2 5 5 0 255 Intensity O to 100 Lo sH STROBE 160 191 COB ON 192 223 RANDOM Strobe SLOW to FAST 224 kw COB ON DIMMING CURVE MODES Cao L oo S 81 100 THEATRE 101 255 Default to Unit Setting 22 CUEPIX BLINDER WW4 User Manual Ver www elationlighting com CLEANING AND MAINTENANCE C A U T O N Disconnect power before cleaning or maintenance CLEANING Frequent cleaning is recommended to insure proper function optimized light output and an extended life The frequency of cleaning depends on the environment in which the fixture operates damp smoky or particularly dirty env
16. iginal manufactures warranty and increase the risk of damage and or personal injury e Never look directly into the light source of this fixture to prevent risk of injury to your retina which may induce blindness Those suffering from EPILEPSY should avoid looking directly into the light source of this unit at all times e The fan and air inlets must remain clean and never blocked Allow approx 6 15cm between this fixture and other devices or a wall for proper cooling e Always disconnect from main power source before performing any type of service and or cleaning procedure Only handle the power cord by the plug end never pull out the plug by tugging the wire portion of the cord e Do not operate this fixture if the power cord has become frayed crimped and or damaged If the power cord is damaged replace it immediately with a new one of similar power rating CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com GENERAL GUIDELINES NEVER OPEN THIS FIXTURE WHILE IN USE During the initial operation of this fixture a light smoke or smell may emit from the interior of the fixture This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp and will decrease gradually over time This fixture is a professional lighting effect designed for INDOOR DRY LOCATIONS ONLY on stage in nightclubs theatres etc Please make sure there are NO FLA
17. ironments can cause greater accumulation of dirt on the fixture s optics e Clean the external lens surface at least every 20 days with a soft cloth to avoid dirt debris accumulation e Never use alcohol solvents or ammonia based cleaners MAINTENANCE Regular inspections are recommended to insure proper function and extended life There are no user serviceable paris inside this fixture please refer all other service issues to an authorized Elation service technician should you need any spare parts please order genuine parts from your local Elation dealer Please refer to the following points during routine inspections e A detailed electric check by an approved electrical engineer every three months to make sure the circuit contacts are in good condition and prevent overheating e Be sure all screws and fasteners are securely tightened at all times Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall e Check for any deformations on the housing color lenses rigging hardware and rigging points ceiling suspension trussing Deformations in the housing could allow for dust to enter into the fixture Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously injure a person s e Electric power supply cables must not show any damage material fatigue or sediments Never remove the ground prong from the power cable 23 CUEPIX BLINDER WW4 User Man
18. nd controller manufactures as a form of communication between intelligent fixtures and controllers DMX allows all makes and models of different manufactures to be linked together and operate from a single controller This is possible as long as all the fixtures and the controller are DMX compliant A DMX controller sends the DMX data instructions to the fixture allowing the user to control the different aspects of an intelligent light DMX data is sent out as serial data that travels from fixture to fixture via data IN and data OUT XLR terminals located on the fixtures most controllers will only have output jacks DMX LINKING To ensure proper DMX data transmission always use proper DMX cables and a terminator When using several DMX fixtures try to use the shortest cable path possible Never split a DMX line with a Y style connector The order in which the fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a starting DMX address of may be placed anywhere in the DMX chain at the beginning at the end or anywhere in the middle The DMX controller knows to send data assigned to address to that fixture no matter where it is located in the DMX chain The CUEPIX BLINDER WW4 can be controlled via DMX 512 protocol and the DMX address is set via the control menu DATA CABLE DMX Cable REQUIREMENTS For DMX and Master Slave Operation Your fixture and your DMX controller r
19. ps to the yoke rigging bracket using a M10 screw fitted through the center hole 10 CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com MOUNTING POINTS e Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury e Fixture is fully operational in the specific mounting positions as illustrated below fer SAFETY CABLE Always use a Safety Cable whenever installing this fixture in a suspended environment to ensure the fixture will not drop if the clamp fails 11 CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com SECURING Regardless of the rigging option you choose for your CUEPIX BLINDER WW4 always be sure to secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the base of the unit as illustrated below Be sure to only use this designated rigging point to attach the safety cable SAFETY CABLE RIGGING POINT C22 wise ue CUEPIX BLINDER WW4 12 CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com UNDERSTANDING DMX DMX 512 DMX is short for Digital Multiplex This is a universal protocol used by most lighting a
20. t desired Dimming Curve Theatre Pixel Flip STANDARD FLIP 1 FLIP 2 FLIP 3 FLIP 4 er Ry ae see Pixel Flip Section NO DMX MODE Hold Blackout Program Define how fixture reacts when NO DMX signal present Ethernet Set Service PIN Fixture ID Password 050 Fixture ID Set IP address Device IP Addr ERO sink l Need to enter Service PIN to access this menu Fixture ID Set Subnet Mask Ctrl Addr aes e a Need to enter Service PIN to access this menu Fixture ID 000 255 set DMX Universe number Universe Need to enter Service PIN to access this menu Ethernet Set Protocol Set CH 01 02 04 05 07 09 Enter Service Password to access Ethernet Menus Kling Net AriNet set Protocol Ethernet Set Set Network switch Network Switch 18 CUEPIX BLINDER WW4 User Manual Ver 1 ELATION i i i Qs www elationlighting com ELATION CUEPIX BLINDER WW4 INTERNAL MACRO MENU specifications are subject to change without any prior written notice MACRO OPTIONS VALUES DESCRIPTION W1 000 255 Flash00 99 01 STATIC W2 000 255 Flash00 99 seven Color Dreaming W3 000 255 Flash00 99 speed amp Flash Adjustable W4 000 255 Flash00 99 Dreaming 02 DREAM Speed0o 99 Flash0o 99 Speed amp Flash Adjustable 03 METEOR Speed00 99 Flash00 99 mon Speed amp Flash Adjustable Fade 04 FADE Spoeed00 99 Flash0o 99 Speed amp Flash Adjustable Change 05 CHANGE Speed00 99 Flash00 99 Speed amp Flash Adjustable 06 FL
21. tart to listen to the channel number you have set based on the quantity of control channels DMX channels of each fixture That means changing the settings of one channel will only affect the selected fixture In the case of the CUEPIX BLINDER WW4 when in the 9 Channel Mode you should set the starting DMX address of the first unit to 1 the second unit to 10 1 9 the third unit to 19 10 9 and so on Note During start up the CUEPIX BLINDER WW4 will automatically detect whether a DMX data signal is being received or not If the fixture is not receiving a DMX signal please check the following The 3pin or Spin XLR input plug cable with DMX signal from controller is not connected or is not inserted completely into the DMX input jack of the fixture The DMX controller is switched off or defective The DMX cable or connector is defective A DMX terminator has been inserted into the last fixture in your DMX chain 16 CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com FIXTURE MENU ON BOARD SYSTEM MENU The CUEPIX BLINDER WW4 comes with an easy to navigate system menu The next section will detail the functions of each command in the system menu LCD MENU CONTROL PANEL The control panel see image below located on the top of the fixture allows you to access the main menu and make all necessary adjustments to the CUEPIX BLINDER WW4 During normal operation pressing MODE button once will
22. ual Ver 1 ELATION www elationlighting com TECHNICAL SPECIFICATIONS FEATURES High Power Long Life Warm White COB LEDs 62 Beam Angle 100 Field Angle Individual Control of Each COB Module 5 Variable Dimming Curve Modes RDM Remote Device Management Flicker FREE Operation for TV and FILM SOURCE 4 100W Warm White COB LEDs 100 000 Hour Average Life EFFECTS strobe Variable and Selectable Dimming Curves CONTROL CONNECTIONS 6 DMX Channel Modes 1 2 4 5 7 9 A Button Control Panel and LCD Menu Display ArtNet KlingNET Protocol Support RDM Remote Device Management 2 RJ45 Ports pin and Spin DMX In Out RDM Remote Device Management powerCON Power In Out SIZE WEIGHT Length 15 7 400 mm Width 6 9 174 mm Horizontal Height 17 4 441 mm Weight 21 0 Ibs 9 5 kg ELECTRICAL THERMAL AC 100 240V 50 60Hz 427W Max Power Consumption Power Linking 1pcs 110V 4pcs 220V 5 F to 113 F 15 C to 45 C APPROVALS RATINGS CE IP20 Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 24 CUEPIX BLINDER WW4 User Manual Ver 1 ELATION www elationlighting com Qe 9 9 PHOTOMETRIC DATA n ar AA Yi on bo 62 100 el Beam Field Man i Pi 2m a A n 3m Man NN ANY ui 4m 5m m ft m ft m ft m ft m ft Distance 1 3 3 2 6 6 3 9 8 4 13 1 5
23. www elationlighting eu info elationlighting eu DOCUMENT VERSION IEY Please check www elationlighting com for the latest revision update of this manual D t Soft ayi ocument sotiware Channel Modes Version Version 11 2014 1 2 4 5 7 9 Initial release 2 CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com CONTENTS Warranty General Information safety Instructions General Guidelines Fixture Overview Fixture Installation Fixture Menu 17 DMX Channel Functions And Values Cleaning and Maintenance Technical Specifications Optional Accessories Understanding DMX 3 CUEPIX BLINDER WW4 User Manual Ver 1 www elationlighting com GENERAL INFORMATION INTRODUCTION Congratulations you have just purchased one of the most innovative and reliable lighting fixtures on the market today The CUEPIX BLINDER WW4 has been designed to perform reliably for years when the guidelines in this booklet are followed Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit These instructions contain Important information regarding safety during use and maintenance UNPACKING Thank you for purchasing the CUEPIX BLINDER WW4 by Elation Professional Every CUEPIX BLINDER WW4 has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have oc
Download Pdf Manuals
Related Search