Product Manual
Contents
1. Compatibility Modes H Frequency V Frequency Mode Resolution KHz Hz VGA 720x350 31 47 70 VGA 720x400 31 47 70 VGA 640x480 31 47 60 VESA 640x480 37 86 72 VESA 640X480 37 5 75 VESA 800x600 35 16 56 VESA 800x600 37 88 60 VESA 800x600 46 88 75 VESA 800x600 48 08 72 VESA 1024x768 48 36 60 SUN 1024x768 52 45 65 VESA 1024x768 56 48 70 VESA 1024x768 60 02 75 Apple Mac II PT1500MX 640x480 67 35 0 PT1550MX PT1501MX only Apple Mac PT1500MX 832x624 75 49 7 PT1550MX PT1501MX only 22 Touch Screen Driver Installation Driver Installation Process 1 Before you start to install the touch driver please be sure the USB or the RS 232 Serial cable is connected from the PC or the LCD display Uninstall any touch screen driver that may be on your system Click on the driver link found on the CD ROM Follow instructions as found below a fF DN After installation is complete click Finish and restart your computer to complete installation PT1500MX PT1550MX PT1501MX Install Instructions The PT1500MX PT1550MX PT1501MX is available with both RS232 and USB connections The touch driver is located on the enclosed CD ROM for these operating systems Windows VISTA 64 32 bits XP 2000 ME 98 XP Embedded Linux WinCE NET Please Note The PT1501MX with Capacitive Touch Screen is Microsoft Windows HID Human Interface Device compatible if you us2. ss ER eb Mer EI EI Q Built in speakers 1W X 2 Touch Screen for PT1500MX PT1550MX O O O O O O D 5 wire resistive touch screen for finger and stylus input Surface Anti glare treatment Interface Dual RS 232 Serial USB controller Durability 35 million touches at a single point Hardness of surface 3H Typical Operating force 40g 200g when using a silicon rubber tipped pen with a 1 mm diameter minimum and a hardness of 60 degree Transmittance 82 5 Driver Windows VISTA XP 2000 ME 98 CE XP Embedded Linux Apple Mac OS Touch Screen for PT1501MX LI LI LI O UU O Capacitive touch screen for finger input Surface Anti glare treatment Interface Dual RS 232 Serial USB controller Durability 200 million touches at a single point Hardness of surface 6H Typical Operating force 15g Transmittance 85 5 Driver Windows VISTA XP 2000 ME 98 CE XP Embedded Linux Apple Mac OS Touch Screen for PT1505MU PT1555MU LI LI LI LI Surface Acoustic Wave SAW touch screen for finger and stylus input Surface Anti glare treatment Interface USB controller Durability 30 million touches at a single point a Hardness of surface Mohs Hardness rating of 7 Operating force 80g min when using a soft tipped stylus with an 8mm diameter minimum Operating force Less than 100 gram Transmittance 92 5 Driver Windows VISTA XP 2000 98 Sone KE P
3. Auto button 3 Adjust the value of the adjustment items by pressing the A or W button 1 The OSD menu will automatically close if you have left it idle for a pre set time 2 To disable the OSD menu buttons please follow the instructions below Please note the monitor has to be ON with a valid signal preset a Press and hold the Power and Menu key simultaneously for 4 seconds b The wording OSD Locked will appear for 4 seconds on the monitor This indicates that all the buttons with the exception of the power button are now disabled 3 To enable the OSD menu buttons please follow the instructions below Please note the monitor has to be ON with a valid signal present a Press and hold the Power and Menu key simultaneously for 4 seconds b The wording OSD Unlocked will appear for 4 seconds on the monitor This indicates that all the buttons are now enabled 187 On Screen Display Menus Main OSD Menu ITEM SUB MENU CONTENT Contrast 0 100 Adjusts the maximum luminance level of the monitor Brightness 0 100 Adjusts the backlight of the monitor Auto Adjust NO YES Automatically adjusts the system clock 5 The screen is moved horizontally right and left 1 pixel Left Right WER pitch increment Down Up 0 100 The screen is moved vertically up and down 1 line increment The ratio of dividing frequency of the dot clock is Hori
4. EE 8 Product EE ER 8 Kensington Security le nh tene dekken en 9 VESA Mount your MONO reren ee dee 10 Start ele Ee E 12 User Controls in saneren daneen naaa desen sede eneen 15 Front Panel GONFOIS arsnsarserersnrnrennansensridnn nit deadsenveidnandndianennvardnaeded 15 How to Use the OSD Men s asnserntaner sienna 16 On Screen Display MenUS 232 siento tiated eed 17 Appendix E 18 Tr bleshooting ee 18 Warming SION crccoves ne seceesneds nena re e EEEE E E ESES 19 ek lee EE 19 P GONG tO SIGE rsr rendent 19 POUT OL RANGE ee EE 19 en Product Dimensions nennen eeenerenerenerenerenerenerenerenerenereneren enn 20 Compatibility MOO OS senses nrden ser erndtend sends 21 Touch Screen Driver Installation eneen 22 Product Registration and Technical Support 27 Tl Usage Notice A Warning To prevent the risk of fire or shock hazards do not expose this product to rain or moisture A Warning Please do not open or disassemble the product as this may cause electric shock Precautions Follow all warnings precautions and maintenance as recommended in this user s manual to maximize the life of your unit Do a Turn off the product before cleaning a Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50 50 mixture of water and isopropyl alcohol Q Use a soft cloth moistened with mild detergent to clean the display housing a Use only high
5. instructions as shown on pop up windows Using the USB connection 1 Be sure that USB cable is connected from the computer 2 Power on the computer 3 Load the touch screen driver CD 4 Follow the step by step instructions as shown on pop up windows If you are using a PC running Windows VISTA follow the instructions below Using the RS232 connection 1 Be sure that RS232 cable is connected from the computer 2 Power on the computer 3 Load the touch screen driver CD 4 Follow the step by step instructions as shown on pop up windows Using the USB connection 1 Be sure that USB cable is connected to the computer 125 2 Power on the computer 3 No need to install USB driver from the CD as it is a HID device The system will recognize the HID device and load the driver automatically If the touchscreen is out of calibration double click on the HID calibration utility and do the 4 points calibration 4 Install Windows VISTA driver and follow the step by step instructions to get the full touchscreen features A special calibration tool can be installed for improved touch position accuracy See Optional Capacitive Calibration Tool Install section for more information If you are using a PC running Windows XP Embedded follow the instructions below Express 1 Power on the computer Make sure that the RS232 or USB cable is connected to the computer Be sure that your EWF is disabled
6. the tabs snap into place You may also keep the cables in order by using the cable organizer Included Cable Organizer A Note You can place the LCD flat horizontally to make it easier to connect the cables Please make sure that you place it on an even surface lest the LCD should be damaged by scratches or collision Connecting the Display Figure 11 1 To setup this display please refer to the following figure and procedures 1 Be sure all equipment is turned off 2 Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet 11 1 3 Connect the D SUB cable from the display s VGA input connector to the D SUB connector of your host computer and tighten the screws 11 1 4 Connect the Audio In cable from the audio input port of your display to the Audio out port of your computer 11 1 5 Connect the RS 232 or USB cable from the RS 232 or USB port of your display to the RS 232 port 11 1 or USB port 11 1 of your computer 6 Configure the touch screen Refer to the Touch Screen Driver Installation section on page 22 7 Once the touch screen is configured the monitor is ready for use Instructions to attach the magnetic stripe reader to the PC PT1550MX model 1 Attach the USB Type A to A cable to the magnetic stripe reader 2 Route the cable through the cable management opening in the desk stand with the other monitor cables Plug the cable into the P
7. C 4 No driver is necessary 14 A Notice To ensure the LCD display works well with your computer please configure the display mode of your graphics card to make it less than or equal to 1024 x768 resolution and make sure the timing of the display mode is compatible with the LCD display We have listed the compatible Video Modes of your LCD display in the appendix for your reference Figure 11 1 aur D Il ei IS 8 i 145 User Controls Front Panel Controls o leon B Menu ellie No Icon Control Function d MENU Menu button Display the OSD menus 1 Increases the brightness of the display e a KEES mage 2 Increases value of the adjustment items Brightness 1 Decreases the brightness of the display M Minus Minus eE 2 Decreases value of the adjustment items Select To select the adjustment items from O dl Select OSD menus Auto Auto To activate the Auto Adjustment function to obtain an optimum image e di Power Switch Gwitches on off the power of the LCD display 16 How to Use the OSD Menus 1 Press the MENU button to pop up the on screen menu and to select among the four Main Menus 2 Choose the adjustment items by pressing the Select
8. If your EWF is enabled please disable the EWF by using the EWF Manager command or the EWF API for example ewfmgr c disable 4 Once the EWF is disabled click on the XP driver on the CD and follow the step by step instructions as shown on the pop up windows Custom 1 Power on the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Follow the step by step instructions found in the zipped file on the CD If you are using a PC running Windows CE follow the instructions 12e below 1 Power on the computer 2 Make sure that the RS232 or USB cable is connected to the computer 3 Using Platform Builder build an image file by following the step by step instructions found in the zipped file on the CD Please note Do not plug in both RS232 and USB cables Doing so may cause a driver conflict making your touch screen idle PT1505MU PT1555MU Driver Install The touch driver is located on the enclosed CD ROM for these OS Windows VISTA XP 2000 98 1 Be sure that USB cable is connected from the computer 2 Power on the computer 3 Load the touch screen driver CD 4 Follow the step by step instructions as shown on pop up windows 27 Product Registration and Technical Support Register Your Planar Products Today Thank you for choosing Planar To assure you receive all the benefits of your Planar product and services register your Planar product today Visit our website to re
9. PLANAR EE Ee PT1500MX PT1550MX PT1501MX PT1505MU PT1555MU Touch Screen LCD Monitors USER S GUIDE www planar com The information contained in this document is subject to change without notice This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be reproduced translated to another lan guage or stored in a retrieval system or transmitted by any means electronic mechanical photocopying recording or otherwise without prior written permission Windows is a registered trademark of Microsoft Inc Other brand or product names are trademarks of their respective holders Important Recycle Instructions Lamp s inside this product contains mercury This product may contain other electronic waste that can be hazardous if not disposed of properly Recycle or dispose in accordance with local state or federal Laws For more information contact the Electronic Industries Alliance at WWW EIAE ORG For lamp specific disposal information check WWW LAMPRECYCLE ORG E Table of Contents Usage Notice coenen dere eeen teekenen bekenheid bake vaan Ness 3 PCA OIG renate 3 Introdu UON E PrN E EE E 4 About PT1500MX PT1550MX PT1501MX PT1505MU PT1555MU SE EE 4 Touch Screen for PT1500MX PIIBbOMX an nnenenn eeen 5 Touch Screen for PT1501MX EE 5 Touch Screen for PT1505MU PT1555MU nnen nnee 5 Package OvervieW egene Eege 7 Installaatio
10. ackage Overview USB Cable A to A Audio in Cable RS 232 Cable PT1550MX PT1555MU PT1500MX PT 1501MX PT 1550MX SSL USB Cable Ato B Touch Screen Driver User s Guide Installation CD ROM Landing Strip DC Power Supply sold separately le Installation Product Overview Front View yy LCD Display Nee ee Stand _ I PT1500MX PT1550MX PT1501MX Bottom View Without Stand RS 232_ _ VGA option DC IN AUDIO IN USB 5 r AC IN ere as mj A is WN g E ED gt B Se Ciel e DS LE z ae PT1505MU PT1555MU Bottom View Without Stand gt DC IN VGA 5 AUDIO IN 4 USB rAC IN f Fe a i aad EN Fa Tm KN o s gt BCP el so ZL RS Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products The Kensington lock is not included Kensington Security Slot 10 VESA Mount your monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface Standard which defines a physical mounting interface for flat panel monitors
11. and corresponding standards for flat panel monitor mounting devices such as wall and table arms The VESA mounting interface is located on the back of your monitor To mount the monitor on a swing arm or other mounting fixture follow the instructions included with the mounting fixture to be used 75mm VESA Mounting Interface 75mm A Warning Please select the proper screws The distance between the back cover surface and the bottom of the screw hole is 8mm Please use M4 screw diameter with a maximum length of 8 mm Remove the Deskstand 1 Remove stand back cover 2 Remove hinge cover 3 Remove 4 screws and then remove hinge 11 Start Your Installation Remove the Back Cover Please follow these instructions to remove the cover on the back panel of the LCD so that you can hookup the cables to associated connector Figure A 1 To remove the back cover follow the arrows in Figure A and pull out with your fingers and the cover should be removed from the stand Refer to the Remove the Deskstand section on page 10 for a picture 2 Follow the instructions on page 14 Figure 11 1 to connect the cables to the appropriate connectors 3 Attach the cover back to the LCD stand by pressing firmly until
12. e the USB touch screen interface No additional software driver is required for general operation of the touch screen A calibration tool can be installed for improved touch position accuracy See Optional Capacitive Calibration Tool Install section for more information PT1501MX Optional Capacitive Calibration Tool Install If you would like to use the Optional Capacitive Calibration Tool follow the instructions below 1 Open the CD Rom 2 Select the Monitor Size and then Model Number 3 Click on the Load Utility button that appears to the right of the Model Number 4 The HID calibration tool will automatically open From here the user can choose to do the following a b c d e 4 Points Calibration 9 Points Linearization 25 Points Linearization Clear Draw Test Advanced In the Advanced settings area the user may do the following i Adjust the Double Click Area ii Enable auto right click and adjust the auto right click time iii Choose to be either in the HID Mouse Mode or HID Digitizer Mode Windows Vista only iv Simply click the Apply button once the settings are finalized If you are using a PC running Windows XP 2000 ME 98 or Linux operating systems follow the instructions below E Using the RS232 connection 1 Be sure that RS232 cable is connected from the computer 2 Power on the computer 3 Load the touch screen driver CD 4 Follow the step by step
13. gister your product at http www planar com support product_registration html Cables Replacement Lamps Accessories To find cables replacement lamps and accessories for your Planar projector LCD monitor touch screen or other Planar products visit our online store at www PlanarOnline com or find other stores who carry Planar products at http www planar com howtobuy Technical Support Visit Planar at http www planar com support for product registration operations manuals touch screen drivers warranty information and access to Planar s Technical Library for online troubleshooting To speak with Planar Customer Support please have you model and serial number available and dial Planar Support Tel 1 866 PLANAR1 866 752 6271 or 1 503 748 5799 outside the US Hours 24 hours a day 7 days a week Toll or long distance charges may apply Tee Planar Systems Inc Customer Service 24x7 Online Technical Support http www planar com support 1195 NW Compton Drive Beaverton OR 97006 1992 Tel 1 866 PLANAR1 866 752 6271 or 1 503 748 5799 outside the United States Hours 24 hours a day 7 days a week 2008 Planar Systems Inc 11 08 Planar is a registered trademark of Planar Systems Inc Other brands and names are the property of their respective owners Technical information in this document is subject to change without notice 020 0697 00 Rev E
14. mage is unstable and flickering gt Use Phase to make an adjustment Problem Image is scrolling gt Check and make sure the VGA signal cable or adapter is securely connected gt Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the LCD Display Problem Vague image characters and graphics gt Use Clock to make an adjustment If this problem still exists use Phase to make an adjustment 19 Warning Signal If you see warning messages on your LCD screen this means that the LCD display cannot receive a clean signal from the computer graphics card There may be three sources for this problem Please check the cable connections or contact Planar for more information gt No Signal This message means that the LCD Display has been powered on but it cannot receive any signal from the computer graphics card Check all the power switches power cables and VGA signal cable gt Going to sleep The LCD is under the power saving mode in addition the LCD will go into this sleep mode when experiencing a sudden signal disconnecting problem gt Out of Range This message means that the signal of the computer graphic card is not compatible with the LCD display When the signal is not included in the Video Modes list we have listed in the Appendices of this manual the LCD display will display this message Product Dimensions 20 a a
15. quality and safety approved AC DC adapter a Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time Don t a Do not touch the LCD Display screen surface with sharp or hard objects Q Do not use abrasive cleaners waxes or solvents for your cleaning Q Do not operate the product under the following conditions Extremely hot cold or humid environment Areas susceptible to excessive dust and dirt Near any appliance generating a strong magnetic field Indirect sunlight ld Introduction About PT1500MX PT1550MX PT1501MX PT1505MU PT1555MU The PT1500MX PT1550MX PT1501MX PT1505MU PT1555MU is a 15 flat panel screen with an active matrix thin film transistor TFT liquid crystal display LCD Features include Direct Analog signal input Active matrix TFT LCD technology 1024x768 XGA resolution 15 viewable display area 31 5 60 2 kHz horizontal scan 56 3 75 Hz high refresh rate 0 297mm x 0 297mm pixel pitch Auto adjustment function Multilingual OSD user controls VESA DPMS power saving Kensington security slot 75 mm VESA mount Removable base for flexible mounting solutions PT1500MX PT1550MX 5 wire resistive touch screen with dual RS 232 Serial USB controllers a PT1501MX Capacitive touch screen with dual RS 232 Serial USB controllers a PT1505MU PT1555MU SAW touch screen with USB controller EI eB GE AB EK EI E BB
16. zontal size 0 100 adjusted Fine tune 0 100 The phase of the dot clock is adjusted OSD Left Right 0 100 Adjusts the OSD menu screen position left or right OSD Up Down 0 100 Adjusts the OSD menu screen position up or down OSD Time out 0 100 Adjusts the amount of the OSD menu is displayed Select the language used for the OSD menu from OSD Language among English French Japanese Deutsch Spanish Italian Traditional Chinese and Simplified Chinese Volume 0 100 Controls the sound volume Mute No Yes Disables the sound immediately 18 Appendix Troubleshooting If you are experiencing trouble with the LCD display refer to the following If the problem persists please contact your local dealer or our service center Problem No image appears on screen gt Check that all the I O and power connectors are correctly and well connected as described in the Installation section gt Make sure the pins of the connectors are not crooked or broken Problem Partial Image or incorrectly displayed image gt Check to see if the resolution of your computer is higher than that of the LCD display gt Reconfigure the resolution of your computer to make it less than or equal to 1024 x 768 Problem Image has vertical flickering line bars gt Use Clock to make an adjustment gt Check and reconfigure the display mode of the vertical refresh rate of your graphic card to make it compatible with the LCD display Problem I
Download Pdf Manuals
Related Search