Explorer 727 Installation Manual
Contents
1. M5 bolt M5 washer Rubber washer Rubber washer Spacer min 10 mm Installing the antenna 15 Chapter 2 Installing the system 2 4 Placing the terminal 2 4 1 Where to place the terminal General The terminal is designed for installation inside a vehicle It is not suited for outdoor installation Temperature conditions The terminal must be placed in a ventilated area with free space around all sides of the unit except the bottom side Ambient temperature range is 25 to 55 C If the terminal is installed in a location where the ambient temperature may exceed 50 C we recommend placing the terminal where unintentional contact is avoided If the maximum ambient temperature does not exceed 50 C the terminal can be placed in a public area 16 Placing the terminal Chapter 2 Installing the system 2 5 Installing the terminal 2 5 1 Mounting the Basic cable support The Basic cable support comes with the terminal as part of the delivery When mounted on the terminal the Basic cable support offers a number of holders to which you can secure the cables from the terminal using cable strips E J n Pai n v te D T T Nn S To mount the Basic cable support do as follows 1 Remove the two rubber feet from the bottom of the terminal at the connector panel end The mounting bushes are underneath the rubber feet Installing the terminal 17 Chapter 2 Installing the syst2. o a n gt A Besides the normal functions of an IP handset the Thrane amp Thrane IP handset also provides a user interface for the EXPLORER system The IP handset connects to the LAN interface of the terminal and is power supplied with Power over Ethernet PoE through the LAN interface For further information on the IP handset refer to the user manual for the Thrane amp Thrane IP handset IP handset and cradle 3 Chapter l System units 1 4 2 Thrane amp Thrane IP cradle The IP cradle serves as a holder for the IP handset It is power supplied from the terminal using Power over Ethernet PoE The cradle connects to the handset with a coil cord and to the terminal with a standard LAN cable 4 IP handset and cradle Chapter 2 Installing the system 2 1 Unpacking Unpack your EXPLORER system and check that the following items are present e TT 3736A EXPLORER terminal e TT 3053B EXPLORER 727 antenna e TT 3670A IP handset and cradle e Basic cable support kit including an I O connector Installing the system e Power cable e Antenna cable e LAN cable e Installation manual this manual e Getting Started kit including e Getting Started leaflet e Quick Guide EXPLORER 727 CD including electronic versions of User manual Installation manual Quick Guide and Getting Started guide Inspect all units and parts for possible transport damage Note For information on how to install the
3. iii 58 Part numbers Al System Units snai 59 A 2 Spare parts EXPLORER 727 60 A 3 Options and accessories rien 61 Technical specifications B 1 OVerVieW ccccccccsessessssssssssssssssersssnscstrscstrsntcnecees 63 B 2 EXPLORER 727 antenna ore 63 B 3 EXPLORER terminal 68 lt lt uulilt 7 GG 75 urli ll lulu 79 Chapter 1 System units n i w 72 gt Val 1 1 Introduction The basic system consists of three units The terminal the antenna and the IP handset with cradle 12 EXPLORER terminal The terminal which contains the primary electronic parts is designed for wall or desktop installation The terminal supplies 23 0 30 0 V DC to the antenna through a single coaxial cable The DC input for the terminal is designed for both 24 V DC and 12 V DC power supply Chapter l System units 13 EXPLORER 727 antenna The EXPLORER 727 antenna is a mechanical tracking antenna consisting of a 2 axis stabilized antenna with RF unit antenna control unit and GPS antenna The antenna is dedicated to the Inmarsat BGAN Broadband Global Area Network system and is designed for roof mounting on a vehicle All communication between the antenna and terminal passes through a single coaxial cable 2 EXPLORER 727 antenna Chapter 1 System units 14 IP handset and cradle 1 4 1 Thrane amp Thrane IP handset un
4. To use the magnetic mounts do as follows 1 First attach the magnets to the antenna WEUS The antenna must have a clearance of 10 mm above the base plane If the base plane is curved it may be necessary to place extra spacers to ensure the clearance of 10 mm There are 3 legs on the antenna Place one magnet under each leg as shown on the drawing on the next page Installing the antenna 13 Chapter 2 Installing the system 2 Place the antenna with magnets on the roof of the car Remember that the magnets only work on a roof made of magnetizable material Detaching the antenna Grab the antenna near one of the magnets and lift it When one magnet is loose the other two are easy to break off In some situations the magnetic force may be so great that it is necessary to unscrew the antenna first and remove the magnets separately 14 Installing the antenna Chapter 2 Installing the system 2 3 6 Mounting the antenna directly on the vehicle roof The antenna may be mounted directly on the roof of your car using three M5 bolts spacers and rubber washers This solution requires that you drill three holes in the roof of the car LL u XIe EU There must always be a clearance of min 10 mm between the bottom of the antenna and the mounting surface Mounting accessories are included with the antenna Note the individual position of washers and spacers J n Pai Nn v te D T T n S
5. 66 Item Specification Solar radiation 1120 W m according to MIL STD 810F 505 4 Air Pressure transport 4572 m AMSL MIL SPEC 810E 500 4 a Note that these specifications only apply for the antenna alone The values will differ depending on the mounting method Especially the max velocity is lower when the antenna is mounted with brackets or magnetic mount EXPLORER 727 antenna Appendix B Technical specifications B 2 3 Antenna outline dimensions EXPLORER 727 antenna Do iS 5 g uy em A w a Da ci T A 3 pcs 96 0 mm 0477 TNC V connector EXPLORER 727 antenna 67 Appendix B Technical specifications B 3 EXPLORER terminal B 3 1 General specifications Global services Voice 4 kbps AMBE 2 or 3 1 KHz Audio Data 64 kbps UDI Standard IP 432 432 kbps Streaming IP 32 64 128 256 kbps SMS Up to 160 characters 2 wire telephone Two connectors R 11 female 600 Q ITU T Rec G interface 473 standard DTMF telephone Supported cable length up to 100 meters 68 EXPLORER terminal Appendix B Technical specifications Item Specification LAN interface Four connectors R 45 female Conforms with IEEE 802 3 af 10 100 Mbps Supported cable length up to 100 m PoE max 15 4 W on each port Total PoE power 64 W at 24 V operation 32 W at 12 V 1 0 interface
6. EL 273 366 5 231 EXPLORER terminal Appendix B Technical specifications End view with serial number label and heat label VON Weight 2 5 kg Dimensions are in mm n iS o S E GS 1 2 Nn S S dei EXPLORER terminal 73 Appendix B Technical specifications B 3 3 Measuring the source impedance Select a power outlet from the 24 V DC or 12 V DC system and measure the source impedance of the installation as described below Measure the voltage without load R var disconnected Set the current to e g 1 A by adjusting R var and measure the corresponding voltage change Example 1A and 50 mV Source impedance 50 mV 1 Amp 50 mQ Battery 12 24 V DC Power outlet for terminal 4 e ree ile I Vehicle installations 1 I I 74 EXPLORER terminal AMSL ATB AWG BGAN cD CM DC DTMF Glossary Above Mean Sea Level Antenna Tracking Board American Wire Gauge A means of specifying wire diameters Broadband Global Area Network A mobile satellite service that offers high sp
7. Output Open switch hold off voltage Open circuit resistance Closed switch voltage Input Input resistance Voltage Voltage High Voltage Low One connector with 5 configurable inputs outputs Open collector Short circuit protected at 1 5 A and reverse polarization protected max 32 V min 130 KQ max 1 V DC at 50 mA min 130 KQ Max 32 V Min 2 2 V Max 1 2 V L Band output Not currently used One connector SMA female Rx output 1525 1559 MHz 105 dBm to 80 dBm EXPLORER terminal 69 Nn pz a v o Q Nn 5 v S tS a Appendix B Technical specifications Standby current Ignition function off max 15 mA Remote on off in DC connector off max 2 mA Relative Humidity 95 non condensing at 40 C 70 EXPLORER terminal Appendix B Technical specifications B 3 2 Outline dimensions terminal Connector panel and bottom view including Basic cable support n iS o S i GS 1 2 Nn S S dei M4 x 6 mm 4 pes 250 6 x 6 mm 4 pcs oo j eon cable support cE a le i alla all gl EXPLORER terminal 71 Appendix B Technical specifications Side view and top view including Basic cable support 264 5
8. Thrane Inc Thrane amp Thrane Shanghai 509 Viking Drive Suites K Land M Unit 602 Building 4 Virginia Beach VA 23452 289 Bisheng Rd USA Zhangjiang High tech Park Pudong 201204 Shanghai P R China Safety summary The following general safety precautions must be observed during all phases of operation service and repair of this equipment Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design manufacture and intended use of the equipment Thrane amp Thrane A S assumes no liability for the customer s failure to comply with these requirements Observe marked areas Under extreme heat conditions do not touch areas of the terminal or antenna that are marked with this symbol as it may result in injury Microwave radiation hazards During transmission the antenna in this system radiates microwave power This radiation may be hazardous to humans close to the antenna When the system is powered make sure that nobody gets closer than the recommended minimum safety distance The minimum safety distance is 1 m to the side and above the antenna when the EXPLORER 727 is powered The safety distance of 1 m does not apply directly below the antenna as the radiation forms a hemisphere above the antenna Service User access to the interior of the system units is prohibited Only a technician authorized by Thrane amp Thrane A S may perform service failure
9. A 3 1 Cables Item Part number Antenna cable RG214 U 50 m 403722A option 947 Antenna cable RG223 U 14 m 403722A option 943 Antenna cable S 10162 B 11 92 m 403722A option 955 DC cable 6 m 403722A option 009 A 3 2 Magnetic mount kit Item Part number Magnetic mount kit 403722A 920 Options and accessories 61 Appendix A Part numbers 62 Options and accessories Appendix B Technical specifications B 1 Overview This chapter contains specifications for the EXPLORER 727 system including the terminal and antenna n c 5 v i GS o 2 Nn S S dei Note For specifications and outline drawings for the Thrane amp Thrane IP handset refer to the manual for the IP handset B 2 EXPLORER 727 antenna B 2 1 General specifications Item Specification Type BGAN Class 10 land vehicular mechanical tracking antenna Polarization RHCP Rx Freq Band 1525 0 1559 0 MHz Tx Freq Band 1626 5 1660 5 MHz GPS 1575 42 MHz Channel Spacing 1 25 kHz 63 Appendix B Technical specifications Item Specification Antenna element Gain RX band min 12 7 dBi Gain TX band min 13 26 dBi G T G T gt 12 5 dBK EIRP Min EIRP 8 dBW Max EIRP 18 dBW Return loss Better than 10 dB 50 Q Cable losses RF attenuation at 1660 MHz max 20 dB at 54 MHz max 4 dB at 3
10. IP handset and cradle refer to the user manual for the handset Chapter 2 Installing the system 2 2 Placing the antenna 2 2 1 Obstructions Obstructions can cause signal degradation The amount of degradation depends on the size of the obstruction and the distance from the antenna As a rule of thumb any obstruction that subtends an angle of less than 3 at the antenna has limited effect The table below gives a guideline for obstruction sizes that will cause limited degradation Distance of Obstruction Size of Obstruction 3m 16 cm 5m 26 cm 10m 52 cm 20m 104 cm 2 2 2 Radiation hazard The EXPLORER 727 antenna radiates up to 18 dBW EIRP This translates to a minimum safety distance of 1 m from the antenna while it is transmitting Note that the safety distance applies to a hemisphere above the antenna The antenna does not radiate power directly below the antenna 2 2 3 Interference Do not place the antenna close to interfering signal sources or receivers We recommend that no other antennas are located within three meters of the antenna If other equipment is installed near the EXPLORER 727 we recommend testing the total system by operating all equipment simultaneously and verifying that there is no interference 6 Placing the antenna Chapter 2 Installing the system 2 3 Installing the antenna 2 3 1 Antenna cables Guidelines A coaxial cable for connection between the antenna and termin
11. bumpy We recommend mounting the antenna on the roof rails or directly on the roof instead of using the magnetic mount kit Make sure that all mounting bolts and nuts are secured properly and that the material of the mounting surface is strong enough to hold the antenna during the intended use Installing the antenna 9 Chapter 2 Installing the system 2 3 3 Mounting the antenna 10 The antenna can now be installed on the roof of the vehicle with three stainless steel bolts You may choose between three methods e Attach the antenna to the roof rails on your vehicle using the dedicated mounting brackets delivered with your EXPLORER 727 system e Attach the antenna using the magnetic mount kit from Thrane amp Thrane Mount the magnetic feet on the antenna and the magnetic force will keep the antenna fixed to the vehicle roof Note that this method requires a vehicle roof made of magnetizable material e Mount the antenna directly on the roof of the vehicle This method requires that you drill holes in the roof of the car Remember to leave min 10 mm space between the antenna and the roof Refer to the previous section Safety on page 9 Installing the antenna Chapter 2 Installing the system 2 3 4 Mounting the antenna on the roof rails on the vehicle Overview Using dedicated brackets you can attach the antenna to the roof rails on your vehicle For ordering information see Roof rail mount kit on page 60 N N E
12. for the connector and the colors of the corresponding wires Pin Color of wire in number Pin function power cable Al Vin Red A2 Vin Black 1 not connected Black 2 Remote on off Green 3 not connected Brown 4 not connected Red 5 Remote on off Orange 32 DC power input Mixed D Sub connector 7W2 male A2 543 A1 Chapter 4 Hardware interfaces 4 4 Analog Phone Fax interface 4 4 1 Overview The terminal has two RJ 11 ports which can be used for connection of analog phones fax machines or analog modems SIM Card L Band Antenna Phone Fax Phone Fax 1 Phone Fax 2 Nn v uv E o z v L 5 25 4 4 2 Pin out The Phone Fax connectors are R 11 6 4 female connectors The table and figure below show the pin out for the connectors Pin number Pin function R 11 female connector 1 123456 2 not connected dh 3 Tip 4 Ring 5 not connected 6 Z Analog Phone Fax interface 33 Chapter 4 Hardware interfaces 4 5 ISDN interface 4 5 1 Overview The terminal has one ISDN connector for connecting an ISDN phone or an ISDN modem The ISDN interface supports 56 64 kbps data rate It is configured as the network side i e Rx is an input and Tx is an output 1 L Band Antenna Phone Fax 34 ISDN interface Chapter 4 Hardware inter
13. included 5 diagnostic report 58 dimensions antenna 67 terminal 71 discrete I O interface 38 document number this manual i drainage 8 E error messages 57 events in LED panel 57 logging 58 H handset description 3 hardware interfaces 29 I 1 0 interface 38 ignition connecting to 27 indicators function 52 installation antenna 7 terminal 17 interfaces on terminal analog phone fax interface 33 antenna 30 DC power input 31 discrete I O 38 ISDN 34 LAN 36 overview 29 interference 6 IP handset connecting 37 entering PIN with 45 short description 3 ISDN interface 34 items included in delivery 5 79 Index L LAN interface 36 light indicators function 52 M magnetic mount for antenna 13 manual document number i measuring source impedance 74 microwave radiation iii 0 obstructions distance and size 6 outline antenna 67 terminal 71 P part numbers 59 Phone Fax interface 33 PIN entering in the web interface 46 entering with a phone 45 entering with IP handset 45 pin out analog phone fax interface 33 antenna interface 30 DC power input 32 discrete I O interface 39 ISDN interface 35 LAN interface 37 placing the antenna 6 placing the terminal 16 80 power cable 22 cable extension 24 connecting 26 remote on off 27 sources 21 switching on 43 power input on terminal 31 PUK code 46 R radiation level iii 6 rem
14. name and password for the terminal You have 3 attempts to enter the terminal PIN before you are asked to enter the PUK Pin Unblocking Key The PUK is supplied with your terminal SIM card Enter the PUK followed by a new PIN of your own choice The PIN must be from 4 to 8 digits long If you enter a wrong PUK 10 times the SIM card will no longer be functional and you have to contact your BGAN Airtime Provider for a new SIM card 5 3 3 Entering the PIN using the web interface 46 If yoru SIM card requires a PIN and the PIN has not yet been entered when you start up the web interface the start up page will be the PIN page Enter the PIN and click OK For further information on web interface see the user manual Entering the SIM PIN for the terminal Chapter 5 Starting up the system 5 4 Operating the system 5 4 1 General use The user manual for the EXPLORER 727 system describes general use of the system and goes through all the functions of the web interface It also contains a brief description of how to use the Thrane amp Thrane IP handset with the terminal 5 4 2 User interfaces Overview The main user interfaces for operation of the system are e the built in web interface the Thrane amp Thrane IP handset Built in web interface The built in web interface is used for easy configuration and daily use You access the web interface from a computer connected to the terminal using an Internet browser No in
15. to comply with this rule will void the warranty Do not service or adjust alone Do not attempt internal service or adjustments unless another person capable of rendering first aid resuscitation is present ili Power supply The voltage range is 10 5 32 V DC 14 A 5 5 A Be aware of high start up peak current 20 A at 24 V 5 ms Do not operate in an explosive atmosphere Do not operate the equipment in the presence of flammable gases or fumes Operation of any electrical equipment in such an environment constitutes a definite safety hazard Keep away from live circuits Operating personnel must not remove equipment covers Component replacement and internal adjustment must be made by qualified maintenance personnel Do not replace components with the power cable connected Under certain conditions dangerous voltages may exist even with the power cable removed To avoid injuries always disconnect power and discharge circuits before touching them Install and use the antenna with care Thrane amp Thrane A S assumes no liability for any damage caused by the antenna falling off the vehicle or stressing the mounting base It is the responsibility of the customer to ensure a safe and correct installation of the antenna The instructions in this manual are only guidelines Failure to comply with the rules above will void the warranty About the manual Intended readers This is an installation manual for the EXPLORER 727 s
16. w Per n gt n w DI ec oO n i Installing the antenna on the roof rails Do as follows 1 Mount the brackets from the roof rail mount kit on the 3 legs of the antenna using the bolts nuts and washers from the kit 2 Drill 3 holes in the roof rails matching the position of the 3 brackets Installing the antenna Il Chapter 2 Installing the system 3 Mountthe antenna with the brackets onto the roof rails of the vehicle placing the bolts nuts and washers from the kit as shown on the drawing 4 Tighten all bolts and nuts firmly to secure the antenna to the roof rails 12 Installing the antenna Chapter 2 Installing the system 2 3 5 Magnetic mount Overview For temporary use or to avoid drilling holes you may use a magnetic mount installation kit For ordering information see Magnetic mount kit on page 61 The Magnet Mount kit consists of 3 individual high intensity magnets with rubber coating Each magnet has an adhesive force of at least 420 N and is mounted with a stainless steel M5 center bolt E J n Pai n v te D T fa Vel S Installing the magnetic mount kit K Make sure the roof of the vehicle is made of a magnetizable material Wipe the surface clean before placing the antenna on the roof in order to make a better connection between the magnets and the roof and to avoid scratches in the surface
17. 6 MHz max 3 dB DC resistance loop max 0 6 Q Max cable length between terminal and antenna e RG 223 U 01 14 meter e RG 214 U 01 50 meter e 5S 07262 BD 70 meter e S 10162 B 11 92 meter Antenna power supply 23 0 30 0 V DC 47 W max continuous without cable loss Measured at ATB input Total antenna weight 6 kg 64 EXPLORER 727 antenna Appendix B Technical specifications B 2 2 Environmental specifications Item Specification Water and dust IP 56 dust and water jet proof Ambient Temperature Operational 25 to 55 C Storage 40 to 80 C Operating humidity 100 condensing Rain Up to 100 mm h 0 5 4 5 droplets at 200 km h Ice survival Up to 25 mm of ice non operational Wind Normal operation with relative average wind velocity up to 200 km h 56 m s 108 knots Vibration Random spectrum 1 05 g rms x 3 axes operational 5 to 20 Hz 0 02 g2 Hz 20 to 150 Hz 3 dB octave Vibration non operational Random spectrum 1 7 g rms 2 h x 3 axes 6 h total 5 to 20 Hz 0 05 g2 Hz 20 to 150 Hz 3 dB octave Vehicle motion Turning rate 60 s Turning acceleration 50 s Induced acceleration 0 5 g Velocity Max 200 km h see note below Shock Half sine 20 g 11 ms EXPLORER 727 antenna 65 Vel v D Q Nn To W pai D Appendix B Technical specifications
18. Default configuration 1 GPIO 1 Ringer output active high 2 GPIO 2 Warning Error output 3 GPIO 3 Mute output 4 GPIO 4 Radio silence input 5 GPIO 5 Ignition input 6 Chassis GND Chassis GND 7 DC out 9 15 V DC 50 mA 8 DCin ignition input a The default functions of the I O pins are described in the next section Discrete I O interface 39 Nn v I T J T oS v 5 25 Chapter 4 Hardware interfaces 4 7 3 Default configuration of I O pins 40 The built in web interface of the terminal offers a page for configuring the I O pins The default configuration of the I O pins is as follows Pin 1 Ringer output This pin changes state from low to high when the terminal is notified of an incoming call from the satellite interface When the call is answered or the caller gives up and releases the call the pin changes back to low Pin 2 Warning Error output This pin provides an external signal that indicates active warning error condition s The signal stays active until all warnings errors are cleared Pin 3 Mute output The mute output pin provides an external signal that is active during a phone call The signal can be used to mute external equipment such as a car radio Pin 4 Radio silence input When active the terminal observes Radio Silence The terminal gracefully closes all open connections and deregisters from the BGAN network No transmission is allowed until the
19. I 78 Radio Frequency Electromagnetic wave frequencies between about 3 kilohertz and about 300 gigahertz including the frequencies used for communications signals radio television cell phone and satellite transmissions or radar signals Right Hand Circular Polarization Subscriber Identity Module The SIM provides secure storing of the key identifying a mobile phone service subscriber but also subscription information preferences and storage of text messages SubMiniature version A A coaxial RF connector developed as a minimal connector interface for coaxial cable with a screw type coupling mechanism The connector has a 50 Ohm impedance Short Message Service Trivial File Transfer Protocol A very simple file transfer protocol with the functionality of a very basic form of FTP Since itis so simple itis easy to implement in a very small amount of memory Threaded Neill Concelman A type of RF connector used for terminating coaxial cables The TNC connector is a threaded version of the BNC connector The connector has a 50 Ohm Unrestricted Digital Information A transparent 64 kbps data channel A alarms 57 analog phone fax interface 33 antenna cables 7 dimensions 67 EXPLORER 727 2 installation location 6 installing 7 interference 6 magnetic mount 13 obstructions 6 outline 67 radiation 6 roof rail mount 11 C cable support 17 cables antenna 7 power 22 condensation 8 delivery items
20. INSTALLATION MANUAL Thrane amp Thrane A S EXPLORER 727 Installation manual Document number TT98 126844 B Release date March 27 2008 Information in this document is subject to change without notice and does not represent a commitment on the part of Thrane amp Thrane A S We recommend downloading the latest version of the manual from the Thrane amp Thrane A S web site www thrane com Copyright 2008 Thrane amp Thrane A S All rights reserved Trademark acknowledgements Thrane amp Thrane is a registered trademark of Thrane amp Thrane A S in the European Union and the United States EXPLORER is a registered trademark of Thrane amp Thrane A S in the European Union and the United States Windows and Outlook are registered trademarks of Microsoft Corporation in the United States and other countries Inmarsat is a registered trademark of International Maritime Satellite Organisation IMSO and is licensed by IMSO to Inmarsat Limited and Inmarsat Ventures plc Inmarsat s product names are trademarks or registered trademarks of Inmarsat Other product and company names mentioned in this manual may be trademarks or trade names of their respective owners Company addresses www thrane com Denmark Denmark Company headquarters Thrane amp Thrane A S Thrane amp Thrane Aalborg A S Lundtoftegardsvej 93 D Porsvej 2 DK 2800 Kgs Lyngby DK 9200 Aalborg SV Denmark Denmark USA China Thrane amp
21. Off The terminal is not supplying power to the port 56 Status signaling Chapter 6 Troubleshooting 6 2 3 Event messages Display of event messages The terminal can detect events during POST Power On Self Test PAST Person Activated Self Test or CM Continuous Monitoring When the terminal detects an event that requires your action it issues an event message When your terminal issues an event message the Terminal Power Terminal Antenna Message LAN indicator or the Antenna indicator in the LED panel on top of the terminal signals the event according to the tables Terminal indicator and Antenna indicator in the previous section Activity Link Speed I PoE ea You can see the active event messages in the web interface by clicking the warning symbol in the icon bar at the top in the web interface All events are logged in the event log For information on the event log see Event log on page 58 DI c 5 So e lt n 2 Q e Status signaling 57 Chapter 6 Troubleshooting 6 3 Logging of events 6 3 1 Diagnostic report When contacting Thrane amp Thrane for support please include a diagnostic report The diagnostic report contains information relevant for the service personnel during troubleshooting To generate the diagnostic report access the web interface and select Help Desk Then click Generate report 6 3 2 Event log 58 The event log holds informatio
22. al is delivered with the system If you need a different cable make sure that the cable meets the requirements Preferably choose one of the cable types in Recommended antenna cables on page 7 The maximum allowed RF loss in the antenna cable is 20 dB at 1660 MHz This is to ensure the performance of the system Recommended antenna cables The table below shows recommended cable types and maximum cable lengths for EXPLORER 727 Cable Type Absolute maximum length RG 223 _U 01 14 m RG 214_U 01 50 m S 10162 B 11 92 m Check in the data sheet from the cable supplier that both the RF attenuation and the DC resistance are kept within the maximum specified values e Antenna cable RF attenuation at 1660 MHz max 20 dB incl connector e Antenna cable modem attenuation at 54 MHz max 4 dB Antenna cable modem attenuation at 36 MHz max 3 dB e Antenna cable loop DC resistance max 0 6 Q Installing the antenna 7 E J n Pai n v te D T fa Nn S Chapter 2 Installing the system Also ensure that the specified minimum bending radius is respected If this is not the case the loss in the cable will increase Check the instruction from the cable supplier The bending radius for the coax cable delivered with the system is min 110 mm 2 3 2 Important mounting notes Line of sight Place the antenna with free line of sight in all directions to ensure proper reception of the satellite s
23. by current on page 70 3 3 3 Connecting a Remote on off switch The terminal has a remote on off function When the terminal power switch is in the on position you can remote control the power function By installing a switch that can short circuit the Remote on off pins 2 and 5 in the power connector you can power the terminal on or off with this remote switch When pins 2 and 5 are not short circuited and valid input power is present the terminal is powered on provided the Power switch is in the on position For pin out for the power connector and a description of the wire colors in the power cable see Pin out on page 32 For information on the standby current when the remote on off switch is off refer to Standby current on page 70 in the General specifications To connect power 27 Chapter 3 Connecting power 28 To connect power Chapter 4 Hardware interfaces 4 1 The connector panel The connector panel is placed at one end of the terminal and has the following connectors Port 1 Port 2 e 1L Band connector not currently used e 1Antenna connector TNC e 2 Phone Fax connectors Port lis closest to the antenna connector n w v 5 u w pa w a5 e 1ISDN connector e 4 LAN connectors with Power over Ethernet PoE e 1DC power input connector for connection to 10 5 32 V DC with optional remote on off e Input Output connector with 5 inputs outputs fo
24. connector outline and pin assignments Pin number Pin function R 45 female connector 1 TxD input 12345678 positive PoE 2 TxD input positive PoE 3 RxD output negative PoE 4 not connected 5 not connected c S 6 RxD output negative PoE g i 7 not connected s 8 not connected 4 6 4 Connecting an IP handset To connect the Thrane amp Thrane IP handset to the terminal do as follows Connect the cable from the IP cradle to one of the LAN connectors on the terminal For information on how to install the IP handset refer to the user manual for the handset The cable between IP cradle and terminal must be maximum 80 m Note 4 If you insert a switch or similar between the cradle and the terminal make sure that it conforms to the industry standard IEEE 802 3 af using data pairs LAN interface 37 Chapter 4 Hardware interfaces 4 7 Discrete I O interface 4 7 1 Overview The terminal has an I O connector with 5 configurable inputs outputs DC Input 10 5 32V DC 14 5 5A 1 0 The connector is a WieCon Type 8513S connector A mating I O connector is included in the delivery 38 Discrete I O interface Chapter 4 Hardware interfaces 4 7 2 Pin out The figure and table below show the connector outline and pin assignments WieCon Type 8513S connector OP 123 4 5 6 7 8 Pin number Connection
25. e DI c 5 e e lt n 3 Q e Reset button 51 Chapter 6 Troubleshooting 6 2 Status signaling 6 2 1 Overview The EXPLORER 727 system uses event messages and light indicators to display the status of the system 6 2 2 Light indicators Overview The terminal has a number of light indicators placed in the panel at the top of the terminal a green orange Power indicator a green red orange Terminal indicator a green red orange Antenna indicator a green Message indicator and 3 LAN indicators for each LAN interface showing Activity Green Link Speed Green Yellow and PoE Green Red Power Terminal Antenna Message LAN1 LAN2 LAN3 LAN4 Activity Le eee 7 Oy PoE Tell 52 Status signaling Chapter 6 Troubleshooting General status indicator functions Power Terminal Antenna Message Power indicator Behavior Meaning Steady green Power OK Flashing green The terminal is powering up Flashing orange The terminal is closing down Off No power Terminal indicator Behavior Meaning gt na E Steady green Ready BGAN registration completed 3 Flashing green Please wait process in progress BGAN registration ongoing z Orange Warning temporary malfunction User action is required Status signaling 53 Chapter 6 Troubleshooting 54 Behavior Meaning Red Critical error Check the eve
26. ect the latest software functionality of your EXPLORER system To obtain the latest version of the manual please enter the Thrane amp Thrane web site www thrane com and download the latest version or acquire it from your distributor Related documents vi The below list shows the documents related to this manual and to the EXPLORER 727 system Explains the features and functions of the Thrane amp Thrane IP handset The IP handset works as a standard IP handset but also serves as a user interface for the EXPLORER systems Title and description Document number EXPLORER 727 User Manual TT98 126882 Explains how to set up and use the EXPLORER system EXPLORER 727 Quick Guide TT98 126881 A short guide to the most important functions of the EXPLORER systems EXPLORER 727 Getting Started TT98 126880 Explains how to start up your EXPLORER 727 system and make the first call or data session Thrane amp Thrane IP Handset User Manual TT98 126059 Typography In this manual typography is used as indicated below Bold is used for the following purposes e To emphasize words Example Do not touch the antenna e To indicate what the user should select in the user interface Example Select Settings gt LAN Italic is used to emphasize the paragraph title in cross references Example For further information see Connecting Cables on page vii viii Chapte
27. eed data up to 492 kbps and voice telephony BGAN enables users to access e mail corporate networks and the Internet transfer files and make telephone calls Compact Disc Continuous Monitoring Direct Current or Continuous current In direct current the electric charges flow in the same direction distinguishing it from alternating current AC Dual Tone Multi Frequency The keypad signaling technology that generates two distinct tones when each key is pressed This system allows navigation of voice menus and other advanced calling services All wireless phones use DTMF dialing 75 gt n n amp Glossary EIRP G T GPIO GPS HPA 1 0 IMSO 76 Effective Isotropically Radiated Power The amount of power that would have to be emitted by an isotropic antenna that evenly distributes power in all directions to produce the peak power density observed in the direction of maximum antenna gain A figure of merit of an antenna and low noise amplifier combination expressed in dB G is the net gain of the system and T is the noise temperature of the system The higher the number the better the system General Purpose Input Output Global Positioning System A system of satellites computers and receivers that is able to determine the latitude and longitude of a receiver on Earth by calculating the time difference for signals from different satellites to reach the receiver High Power Amp
28. em 2 Fasten the Basic cable support to the two mounting bushes close to the connector panel on the terminal using two M4 x 6 mm countersunk Screws 3 Install the terminal as described in Mounting the terminal on page 19 18 Installing the terminal Chapter 2 Installing the system 2 5 2 Mounting the terminal Do as follows to mount the terminal 1 Insert four screws through the holes in the mounting bracket and into the mounting surface iS J 2 n Pai n v te D T as Vel S 2 Connect all cables If you are using the cable support secure the cables to the cable support using cable strips Installing the terminal 19 Chapter 2 Installing the system 20 Installing the terminal Chapter 3 Connecting power 3 1 Power source The 12 or 24 V DC supply of the vehicle provides power for the terminal Note Do not use the cigarette lighter socket in the vehicle to supply power for the EXPLORER 727 Connect directly to the 12 or 24 V supply instead Note that the maximum allowed source impedance is much lower for a 12 V DC supply than for a 24 V DC supply Also the total output power available for PoE is limited when the power supply is 12 V DC Connecting power Be aware of high start up peak current 20 A at 24 V 5 ms The terminal is equipped with an internal 20 A Fuse so no external fuse is necessary in order to protect the terminal However in order to avoid short circui
29. faces 4 5 2 Pin out The figure and table below show the connector outline and pin assignments R 45 female connector Pin number Pin function 12345678 1 not connected 2 not connected 3 Rx c input 4 Tx d output 5 Tx e output 6 Rx f input Ri Z 7 not connected E 8 not connected g mo E ISDN interface 35 Chapter 4 Hardware interfaces 4 6 LANinterface 4 6 1 Overview The terminal has four Ethernet LAN ports with Power over Ethernet PoE The Ethernet ports are standard IEEE 802 3 af ports using RJ 45 connectors SIM Card 1 L Band Antenna JO Output Phone Fax 4 6 2 Power over Ethernet PoE One power supply powers all four interfaces with a floating 48 V DC supply 44 57 V DC Therefore the interfaces are not galvanically separated from each other All Tx signals are DC connected to the Positive PoE Voltage and all Rx signals to the Negative PoE Voltage The total output power from all 4 interfaces is 64 W at 24 V DC power supply so all interfaces can support devices of power class 1 2 and 3 4 7 and 15 4 Watt At 12 V DC power supply the total output power for PoE is 32 W This means you cannot use power class 3 devices on all four LAN interfaces In case of power hold up failure on input power PoE will be turned off 36 LAN interface Chapter 4 Hardware interfaces 4 6 3 Pin out The figure and table below show the
30. ignal Do not place the antenna close to large objects that may block the signal After installing and starting up the EXPLORER 727 we recommend checking the signal strength while driving the vehicle in a 360 circle to ensure a clear line of sight in all directions Condensation In some cases there will be condensation inside the antenna Gaskets in the bottom of the EXPLORER 727 antenna are designed to lead any water away from the antenna Make sure these draining gaskets are not blocked Important Make sure there is always a distance of min 10 mm between any part of the antenna bottom and the mounting surface Use 10 mm spacers or higher if necessary at each bolt See the drawing in Mounting the antenna directly on the vehicle roofon page 15 8 Installing the antenna Chapter 2 Installing the system Safety A Caution Itis the responsibility of the customer to ensure a safe installation See guidelines below Under normal driving circumstances the magnetic force of the magnetic mount kit for the antenna should be sufficient to hold the antenna However the magnets may not be able to hold the antenna in place if e the vehicle is involved in an accident e the magnets are not mounted properly E J n Pai n v fe D T fa n S e the roof is not plain or made of a material that will not stick properly to the magnets e the speed of the vehicle is too high and or e the road is very
31. interface and see your current configuration The default value is not saved in the configuration but is only valid until next reboot With the terminal running press and hold the Reset button for 30 seconds until the Power indicator on the terminal is flashing orange The terminal restores factory settings and reboots the system Reset button Chapter 6 Troubleshooting Action Function While the terminal For service use only is booting press The bootloader initiates software upload This and holdthe Reset firmware upload procedure is only to be used if the button other procedures fail due to missing or corrupted firmware This setup uploads software to the terminal from a TFTP server via the LAN connection The procedure is as follows 1 Activate or install a TFTP server on a PC 2 Locate the correct software image xxx dl for the terminal and place it in the TFTP server directory 3 Rename the image to ttexp dl 4 Reconfigure the PC LAN interface to use the static address 192 168 0 2 255 255 255 0 Power off the terminal Connect the PC LAN Interface to the terminal Press and hold down the Reset button oD p Keep the Reset button pressed while powering on the terminal and through the next step 9 Monitor the TFTP server window When the upload starts you can release the Reset button 10 When the TFTP upload finishes the terminal boots up using the new imag
32. lifier Input Output International Maritime Satellite Organisation An intergovernmental body established to ensure that Inmarsat continues to meet its public service obligations including obligations relating to the GMDSS Internet Protocol The method or protocol by which data is sent from one computer to another on the Internet ISDN kbps LAN Mbps PAST PC PIN PoE POST PUK Glossary Integrated Services Digital Network A circuit switched telephone network system designed to allow digital transmission of voice and data over ordinary telephone copper wires resulting in higher quality and speed than are available with analog kilobits per second Local Area Network Megabit per second Person Activated Self Test A test similar to the POST test but activated by the user The PAST causes the system to reset Personal Computer Personal Identification Number A secret numeric password shared between a user and a system used to authenticate the user to the system Power over Ethernet A standard for combining power supply with transmission of data over the Ethernet The source unit injects power into the Ethernet cable and the power is picked up at the connected device Power On Self Test A test sequence that runs every time the system is powered up or reset Pin Unblocking Key 77 gt Si oO n n L Glossary RF RHCP SIM SMA SMS TFTP TNC UD
33. max total impedance measured source impedance impedance of the supplied cable Then calculate the max extension cable length as follows Max impedance in extension cable from step 3 Max length 0 5 x impedance meter from step 2 The length is multiplied by 0 5 above because there are two conductors in the cable Power cable selection Chapter 3 Connecting power Example Note The following example may not be applicable to your installation For example the source impedance of the vehicle power supply varies depending on the type of battery and the temperature Vehicle supply voltage 12 V DC Vehicle source impedance measured 15 mQ Extension cable type 4 mm AWG 11 85 mQ 15 mQ 50 mQ Max cable extension 0 5 x 4 mQ m 25m In this case the power cable can be extended with up to 2 5 m pen o ro 2 cal 6S v D i c If you need more length you can double the maximum allowed length by connecting two cables in stead of one or you can use a cable with a larger diameter Power cable selection 25 Chapter 3 Connecting power 3 3 To connect power 3 3 1 Connecting the power cable Do as follows 1 Connectthe power cable to the DC supply according to the recommendations in the previous section cD If you need a remote on off function connect the wires from pin 2 green wire and 5 orange wire in the power connector to a switch or similar which can con
34. n of all registered events in the terminal or antenna that are also shown in the Antenna and Terminal LEDs on the terminal The log includes the time of the occurrence a short description location of the error etc This information can help troubleshooting errors in the system You can see the event log in the web interface For further information on the web interface see the user manual Logging of events Appendix A Part numbers A 1 System units A 1 1 TT 3722A EXPLORER 727 system Item Part number EXPLORER 727 antenna 403053B EXPLORER terminal 403736A A 1 2 TT 3670A IP handset and cradle Item Part number Thrane amp Thrane IP Handset 403672A Thrane amp Thrane IP Cradle 403674A 59 Appendix A Part numbers A 2 Spare parts EXPLORER 727 A 2 1 Antenna spare parts Item Part number HPA module S 62 124671 GPS module S 60 124765 A 2 2 Roof rail mount kit Item Part number Roof rail mount kit S 41 127102 A A 2 3 Cables Item Part number Antenna cable 2 7 m 5 37 123410 A Antenna cable 8 m 5 37 126878 A Power cable 5 37 125999 LAN cable S 37 204649 005 60 Spare parts EXPLORER 727 Appendix A Part numbers A 2 4 Other spare parts Item Part number n 2 v a E 3 a Getting Started kit S 673736A A 3 Options and accessories
35. n system of your vehicle to power the EXPLORER 727 system When the ignition function is used the EXPLORER 727 will start up when you turn the ignition key of the vehicle K In some cases the system may reboot after power on because of the high start up current For further information see Connecting to the ignition on page 27 Powering the system 43 Chapter 5 Starting up the system 5 2 4 Remote on off Alternatively you may use the Remote on off function In this case leave the power switch in the On position and switch off the terminal remotely using a switch or similar connected to the Remote on off pins in the DC power interface For further information see Connecting a Remote on off switch on page 27 44 Powering the system Chapter 5 Starting up the system 5 3 Entering the SIM PIN for the terminal 5 3 1 Overview If your SIM card requires a PIN you have to enter a PIN to use the system You can enter the PIN using a standard or ISDN phone the IP handset or the web interface For information on how to connect the handset or computer you are going to use refer to the user manual 5 3 2 Entering the PIN using a phone or IP handset To enter the PIN If you have a phone connected to the terminal you can use it to enter the PIN at start up Do as follows e For an analog or ISDN phone Pick up the phone When the terminal is waiting for a PIN you will hear 2 beeps pause 2 beeps etc Dial lt PIN g
36. nect disconnect these two pins See Connecting a Remote on off switch on page 27 for details 2 Connect the D sub connector on the power cable to the DC input connector on the terminal For information on pin out see DC power input on page 31 For specifications of the DC input on the terminal see EXPLORER terminal on page 68 26 To connect power Chapter 3 Connecting power 3 3 2 Connecting to the ignition The terminal has an ignition function When this function is used the EXPLORER 727 switch on off when you start stop the engine of your vehicle provided the power switch on the terminal is on Use the SETTINGS gt Discrete I O page in the web interface to configure the ignition function according to your needs Select if the Ignition pin should be active high or low and set up a delay determining how long the terminal will stay on after switching the ignition off For further information on the web interface see the EXPLORER 727 user manual To implement the ignition function connect the appropriate pin in the I O connector to the ignition key switch e Ifthe ignition signal is active high connect pin 8 to the ignition input and pin 5 to ground o 2 v D iS e If the ignition signal is active low connect pin 5 to the ignition input and pin 8 to DC Pin out and default functions Discrete I O interface on page 38 Standby current when the ignition power is off Stand
37. nt log If the problem is in the EXPLORER system and you cannot solve it contact your distributor and return the unit for repair if necessary Antenna indicator Behavior Meaning Steady green Tracking The antenna is ready for use Flashing green Please wait process in progress Slow flashing The antenna is starting up Rapid flashing Sky scan Orange Warning temporary malfunction User action is required Red Critical error Check the event log If the problem is in the EXPLORER system and you cannot solve it contact your distributor and return the unit for repair if necessary Status signaling Chapter 6 Troubleshooting Message indicator Behavior Meaning Flashing green A new SMS message has arrived Off No new messages or the unit is off i T o lt Nn 30 2 3 2 E Status signaling 55 Chapter 6 Troubleshooting LAN indicator functions LAN1 LAN2 LAN3 LAN4 Activity rtl ei 7 7 i E PoE SS ee Activity indicator Behavior Meaning Flashing green The LAN port is active Link Speed indicator Behavior Meaning Green Link speed is 100 Mbps Yellow Link speed is 10 Mbps Off The link is down PoE indicator Behavior Meaning Green The terminal is supplying power to the LAN port Red The connected device requires more power than the terminal can supply to the LAN port
38. ote on off 27 reset button accessing 49 functions 50 roof rail mount for antenna 11 S safety summary iii SIM card inserting 41 removing 42 source impedance measuring 74 spare parts 60 specifications 63 system units EXPLORER 727 antenna 2 IP handset 3 terminal 1 T technical specifications 63 temperature 16 terminal cable support 17 installation location 16 installing 17 outline and dimensions 71 tools for operation 47 troubleshooting 49 typography used in this manual vii U user interfaces 47 Index 81 Thrane amp Thrane A S info thrane com e www thrane com v a 5 iS fe oo o So n ey si pie d
39. pin is deactivated Pin 5 8 Ignition input The ignition function uses pin 5 together with pin 8 DC in Connect the appropriate pin to the ignition key switch of the vehicle If the input should be active high connect pin 5 to Ground and use pin 8 to switch on the terminal by pulling it high 10 32 V DC If the input should be active low connect pin 8 to positive DC voltage and use pin 5 to switch on the terminal by pulling it low lt 1 2 V DC Pin 7 non configurable Apart from the 5 configurable inputs outputs the DC connector has an additional output pin pin 7 DC output which can be connected to a ringer relay or similar The output voltage is 9 15 V 50 mA For information on how to configure the I O pins see the user manual for the EXPLORER 727 system Discrete I O interface Chapter 5 Starting up the system 5 1 Using the SIM card 5 1 1 Inserting the SIM card The SIM card is provided by your Airtime Provider Insert the SIM card as follows SIM Card 1 1 Open the SIM cover in the left side of the connector panel 2 Insert the SIM card into the SIM slot Place the card with the chip side facing up as shown v 2 n gt n v o 5j ey 5 E n 3 Press gently until it clicks 4 Slide the lock in front of the SIM card 5 Close the cover for the SIM slot 4l Chapter 5 Starting up the system Removing the SIM card Note 4 When the SIM card i
40. r 1 Chapter 2 Chapter 3 Chapter 4 Table of contents System units 11 Imtroduction iii 12 EXPLORER terminal 13 EXPLORER 727 antenna 14 IP handset and cradle Installing the system 21 Unpacking ccccseesccsccssessessessessrssscenees 2 2 Placing the antenna in 2 3 Installing the antenna n 2 4 Placing the terminal in 2 5 Installing the terminal n Connecting power 3 1 Power Source ttirrrecrreeeeeeeneeee 3 2 Power cable selection 3 3 To connect power ssceeceeseceereeeeeeeees Hardware interfaces 4 1 The connector panel 4 2 Antenna interface on terminal 4 3 DC power input iin 4 4 Analog Phone Fax interface 4 5 ISDN interface in 4 6 LAN interface ii Table of contents Chapter 5 Chapter 6 App A App B Glossary Index 4 7 Discrete I O interface rinienene 38 Starting up the system 5 1 Using the SIM card ou ccsscsssssessesssssesssssecsssseceseeneenes 41 5 2 Powering the system ii 43 5 3 Entering the SIM PIN for the terminal _ 45 5 4 Operating the system i 47 Troubleshooting 6 1 Reset button iii 49 6 2 Status signaling in 52 6 3 Logging of events
41. r external control or signaling e 1 ground stud with wing nut For information on how to connect to a specific interface see the next sections 29 Chapter 4 Hardware interfaces 4 2 Antenna interface on terminal 4 2 1 Overview The antenna interface on the terminal connects to the TT 3053B antenna in the EXPLORER 727 system The antenna connector on the terminal is a TNC female connector placed in the connector panel SIM Card L Band Antenna Output Phone Fax For information on cables and how to install and connect the antenna see Installing the antenna on page 7 4 2 2 Pin out The below drawing shows the TNC female connector in the terminal Signal GND 30 Antenna interface on terminal Chapter 4 Hardware interfaces 4 3 DC power input 4 3 1 Overview The DC power input for the terminal is a 10 5 32 V DC 14 5 5 A input with a remote on off function The input is protected against reverse polarity For information on power recommendations and how to connect see Connecting power on page 21 The power connector is a D sub connector placed in the connector panel 2 LO ii DC Input 10 5 32V DC 14 5 5A 1 0 Nn wo uv T J g v g 5 25 DC power input 31 Chapter 4 Hardware interfaces 4 3 2 Pin out The power connector is a Mixed D Sub connector 7W2 control pin male power pin male The below table shows the pin out
42. s removed you cannot use the BGAN menu of the IP handset nor make calls or start data sessions Only emergency calls are allowed and only if permitted by the network However if you have an administrator user name and password you can upload software using the web interface without having a SIM card For further information see the user manual Remove the SIM card as follows 1 Open the SIM cover in the left side of the connector panel L Band Antenna Output KS 2 Slide the lock aside 3 Gently push the SIM card and let it pop out 4 Remove the SIM card and close the cover for the SIM slot 42 Using the SIM card Chapter 5 Starting up the system 5 2 Powering the system 5 2 1 Switching the terminal on To switch on the terminal use the Power switch in the connector panel It normally takes one or two seconds for the LIT terminal to switch on Taj On Off Ay Caution When the system is powered on stay clear of the antenna The antenna emits radio frequency energy not only when the system is used Always keep a minimum distance of 1 m from the EXPLORER 727 antenna 5 2 2 Switching the terminal off To switch off the terminal change the position of the Power switch again Note 4 Wait at least 5 seconds after power off before trying to power on the system again wo 2 Cel gt n v 2 E DD pa n 5 2 3 Ignition You may use the ignitio
43. stallation of software is needed E w n gt 72 dv a i i N An Administrator password is required to access advanced configuration of the system For further information on the web interface refer to the user manual for the EXPLORER 727 system IP handset Apart from the standard functions of an IP handset the Thrane amp Thrane IP handset contains a display menu for the EXPLORER 727 system For further information on the Thrane amp Thrane IP handset refer to the user manual for the IP handset Operating the system 47 Chapter 5 Starting up the system 48 Operating the system Chapter 6 Troubleshooting 6 1 Resetbutton 6 1 1 How to access the Reset button The terminal has a Reset button placed next to the SIM slot behind the SIM cover The functions of this button is described in the next section To press the Reset button use a pointed device i gz o Ea Nn i 2 3 2 E 49 Chapter 6 Troubleshooting 6 1 2 Function of the Reset button The Reset button on the terminal has the following functions Action Function With the terminal running press the Reset button normally The terminal IP address and IP netmask are temporarily set to the default value default IP address 192 168 0 1 With this function even if the IP address has been changed and you do not remember the new IP address you can still access the web
44. t followed by When you hear a busy tone or a dialing tone the PIN has been accepted and you can hang up or dial a number wo 2 Cel gt n v 2 j D pa n For an IP handset Select the BGAN menu select ENTER PIN and enter the user name and password for the terminal Then enter the PIN for the terminal K The ENTER PIN menu item is only available if your SIM card requires a PIN and the PIN has not yet been entered and accepted in the terminal Entering the SIM PIN for the terminal 45 Chapter 5 Starting up the system Wrong PIN Analog phone or ISDN phone If instead of the busy tone or dialing tone you continue to hear 2 beeps pause 2 beeps etc it means the PIN was not accepted Check that you have the correct PIN and try again If a wrong PIN has been entered three times you will hear 3 beeps pause 3 beeps etc This means you have to enter the PUK PIN Unblocking Key provided with your SIM card After entering the PUK you must enter a new PIN of your own choice 4 to 8 digits long Dial the following lt PUK gt lt New PIN gt lt New PIN gt followed by or off hook key Example If the PUK is 87654321 and the new PIN is 1234 dial 87654321 1234 1234 followed by or off hook key If you enter 10 wrong PUKs the SIM card will no longer be functional Contact your Airtime Provider for a new SIM card IP handset After having entered the user
45. t in the power cable connector the DC outlet of the vehicle should be protected by a 30 A fuse or circuit breaker 21 Chapter 3 Connecting power 3 2 Power cable selection 3 2 1 Source impedance 22 The length of the power cable depends on the type of cable used and the source impedance of the DC power installation in the vehicle The maximum allowed source impedance depends on the utilization of the power range of the terminal DC input 10 5 32 V DC 14 5 5 A Select a power outlet from the DC system and measure the source impedance of the installation as described in Measuring the source impedance on page 74 in Appendix B Note 4 If the total source impedance is higher than the limits stated in this section the terminal may start to on off oscillate For further recommendations on power cable selection see the next section Power cable selection Chapter 3 Connecting power 3 2 2 Power cable recommendations Overview The terminal is delivered with a power cable which can be extended according to the recommendations below Red Black o ro 2 Da pi v D i c When extending the power cable positive and negative supply wires must be installed closely together side by side to keep cable inductance low Ensure that cable inductance for the selected cable at the desired length is below the 50 uH requirement If you are going to use the Remote on off function also e
46. xtend the two wires green and orange used for this function For further information see Connecting a Remote on off switch on page 27 Power cable selection 23 Chapter 3 Connecting power Calculating the maximum power cable extension 2h For 24 V DC operation the total impedance must be max 500 mQ including the source impedance in the vehicle installation For 12 V DC operation the total impedance must be max 85 mQ including the source impedance in the vehicle installation The total impedance is made up of the following the source impedance in the vehicle installation the cable impedance of the supplied power cable including the impedance in the joint of the two cables In the following example the impedance of the cable and joint is set to 50 mQ 6 m power cable Note that if the cable length or type is changed the impedance will change accordingly the extension cable impedance To calculate the maximum cable extension do as follows L First measure the source impedance in the vehicle installation as shown in Measuring the source impedance on page 74 Then find the resistance per meter for the cable type you are going to use For 4 mm AWG 11 the value is 4 mQ m at 20 C For 1 5 mm2 AWG 15 the value is 10 mQ m at 20 C For other cable types refer to the data sheet for the cable Calculate the maximum allowed impedance in the extension cable as follows Max allowed impedance in extension cable
47. ystem The readers of the manual include installers of the system and service personnel Personnel installing or servicing the system must be properly trained and authorized by Thrane amp Thrane It is important that you observe all safety requirements listed in the beginning of this manual and install the system according to the guidelines in this manual Manual overview Note that this manual does not cover general use of the system nor does it cover how to use the IP handset that comes with the system For this information refer to the user manual for this system and the user manual for the IP handset both listed in the next section This manual has the following chapters e System units contains a short description of each main unit in the system e Installing the system describes where to place the system units how to mount them distance to other equipment etc e Connecting power explains how to connect the terminal to power and gives recommendations for cables Hardware interfaces describes each interface on the terminal and shows pin out for the connectors e Starting up the system explains how to insert the SIM card power up the system and enter the PIN It also gives a short overview of how to use the system e Troubleshooting describes the function of the Reset button and the light indicators on the terminal It also describes event messages that may appear in the web interface This manual may not always refl
Download Pdf Manuals
Related Search