Cone Art Glass Kiln Instruction Manual
Contents
1. 10 Cut TOP TWO white plastic cable ties used to secure red and black element wires only along inner left edge of control panel along hinges Automatic kilns 11 Remove screws on left side of control panel assembly 12 On sectional kilns remove two 4 screws located inside the gutter on the heat shield just below thermocouple blocks These screws secure kiln sections together and insure a good ground connection between top middle and bottom kiln sections 13 Remove two 4 screws at the inner bottom right corner of gutter adjacent to power cable 14 Tap on and slide gutter to the left to separate from kiln 15 Set gutter control box aside with control panel door facing up 16 Lift top section straight up and off kiln setting aside gently 17 Lift mid section straight up and off kiln setting aside gently 18 Move kiln to new location aoe a 2 Appendix B Element Replacement Kiln elements deteriorate every time the kiln is fired the extent of element wear depends upon the temperature to which the kiln is fired and the amount of corrosive gases released As the average lifetime of a kiln element varies from 50 150 firings occasionally one element or set of elements will require replacement To Replace the Element 1 2 3 Confirm that the kiln 1s disconnected from the power supply by either unplugging from receptacle or disconnecting at breaker box Remove the screws on the right side of the control box panel2. and disconnect from electrical source by either unplugging from receptacle or disconnecting at breaker box With a metal instrument carefully push the element back into place and pin with staples made from Kanthal A 1 wire or equivalent TIP Fire the kiln hotter than normal once in a while if the elements pop out regularly this problem may occur for those firing only to low temperatures 6 Regularly check elements for signs of aging or need of replacement element life span varies greatly with element size as well as temperature and atmosphere to which you are firing 7 Due to the expansion and contraction of heating the electrical connections inside the switch panel may gradually loosen we recommend checking the connections every 25 firings to confirm that they are tight TROUBLESHOOTING CAUTION The following general checkpoints assume a basic working knowledge of electricity it is recommended that electrical testing work repairs only be performed by qualified persons since potentially dangerous voltage is involved The Kiln Does Not Turn On 1 Check all electrical components power cord fuses circuit breaker etc for loose connections damage or malfunctions 2 For kilns with Bartlett V6 CF automatic controllers inspect controller fuse to confirm it is functioning refer to controller manual Tripped Circuit Breaker and or Blown Fuses 1 Confirm that power source wiring exceeds kiln requirements wire gauge may be insu
3. and crack off taking more brick with it CAUTION Never fire the kiln unattended Appendix A Kiln Disassembly In some instances it may be necessary to disassemble the kiln to go through a narrow doorway Before disassembling disconnect kiln from power source save all screws and hardware for reattachment To Disassemble the Kiln 1 Pull out cotter pin from end of lid hinge bar Remove washer and slide out hinge bar rod 2 Remove two lid arm supports by removing two outer nuts only Use a flat head screwdriver to press down on the head of the inner bolt while unscrewing the outer nut Lift off lid Carefully place down to prevent breakage Unlatch all draw latches fastening kiln sections together along edges of each section Remove screws on right side of control panel assembly Swing control box door open Using a pair of pliers gently pull off wires from switch block or terminals Pull off element wires with YELLOW connectors only from relays automatic kilns Disconnect thermocouple wire at ceramic block Note red is negative yellow is positive silver is ground Gently pull off ground wire at left edge of ceramic thermocouple block with pliers then pull out red and yellow wires by loosening screws with a Phillips screw driver 9 Loosen copper connector screws to disconnect TOP Pair only of Black element wires from element Do not remove copper connectors on lower pair of black element wires Leave fastened Automatic kilns
4. and set aside Pull the control box panel open Use a 3mm Allen wrench to loosen the two copper connectors on each end of the element to be replaced take note of the wires to which the element will be re connected if the connectors are corroded replace with new connectors purchased from your dealer Pull the ends of the element through the brick taking care not to damage the brick if the element is brittle it may break into pieces a pair of needle nosed pliers can aid in removal Remove any debris from the element s grooves Place the new element in the grooves push the ends through the holes in the kiln wall If grooves are worn or chipped pin the element into the grooves with staples made from Kanthal A 1 wire element wire or equivalent Re connect the element to the correct switch wires with the copper connectors confirm that they are tight cut off any excess element wire extending beyond the copper connector Close the control box panel replace the panel screws Turn on the power supply and confirm that the new element works properly by visually checking for an orange glow Appendix C Thermocouple Replacement Over time thermocouples gradually corrode and should be replaced at the very first signs of corrosion approximately every 30 firings as even partially corroded thermocouples are not able to gauge temperature correctly and therefore may cause an over firing Your kiln is equipped with TYPE K THERMOCOUPLES Older mode
5. to you Any optional kiln instrumentation you may purchase is covered by the warranties if any provided by its manufacturer and not by Cone Art Kilns Inc What will Cone Art Kilns Inc do Cone Art Kiln Inc will repair or replace any part at its discretion that proves to be defective or is malfunctioning at no charge to you How do I get service Contact Cone Art Kilns Inc at 1 800 304 6185 or your dealer to arrange the return of defective parts Take a moment to fill in the following concerning your kiln this information will be required to obtain warranty repair Kiln s Owner Country kiln is used in Purchased from Date of Purchase Model Number Serial Number Service Voltage 11 Maintenance Notes 12
6. A does not allow us to attach a plug to the kiln s electrical cord Because there are a variety of configurations of electrical plugs and corresponding receptacles it is best to have a electrician determine the connection that best suits the requirements of the kiln and your building s power supply Additionally we encourage your electrician to directly wire the kiln into the breaker box rather than plugging it into an outlet as this option allows for the safest and most efficient kiln operation We advise hiring a qualified electrician to install your kiln as potentially dangerous voltage is involved The information the electrician will require such as volts amps watts and phase in noted on the nameplate of the kiln If the kiln you recently purchased is replacing an old kiln confirm that the existing wire size is correct for the new kiln Prepare Kiln for Test Firing 1 W I S 8 9 Confirm that the kiln is disconnected from the power supply by either unplugging from receptacle or disconnecting at breaker box Position the power cord so that it does not touch the side of the kiln Check that the lid brace is connected securely to the kiln and kiln lid If your kiln has multiple sections inspect the latches that lock sections together to confirm that they have been securely fastened Carefully vacuum any bits of brick dust or debris that may have lodged in the kiln s elements during shipping Confirm that a
7. Cone Art Glass Kiln Instruction Manual ART SAA KILNS TUCKER S Cone Art Kilns Inc 15 West Pearce Street 7 Richmond Hill Ontario L4B 1H6 Tel 905 889 7705 Fax 905 889 7707 Toll Free 1 800 304 6185 www coneartkilns com Table of Contents Tntrod tti N RS TR RE aa cao 2 Kiln SUD an A a tes he ee E EE 3 Checking the Kiln for Damage upon Delivery 3 Selecting the Best Kiln Location rer se unten eee 3 Wnpackine the RTS RE MD nent Nasa e neue 3 Electrical R quirements 24 ein NN M el est 4 Prepare Kiln for Test Pin se rune een int re eS 4 IMPORTANT SAFETY PRECAUTIONS 5 Test Eiros rinpa sarc sees estates hae De TE aca RS is ES 5 Automate KINS eeso osian E E Te RM E ESE 6 Manual KNS hessen oat toc rt a e ae MR a tes 6 Typesof Controll r Nc des E E ATE E ESTE E 6 Preventive Kiln Mamitenance 20 5 2223645 sooo alee ees eee teas eed 6 EFOUDICSHOOUMG 552 5 de etched COTS eG A None eds 7 Appendix A Kiln Disassembly 0c cece cece cence cece eee eee eee eeeeeaeeneenas 8 Appendix B Element Replacement 2 2yocacsisageseiscc ees se tace eee ees 9 Appendix C Thermocouple Replacement 9 Appendix D Switch and Relay Replacement 10 Warranty oee ER TE NP weaved as 11 Maintenance Notes 2 55 eut ns tn dd ends Aster rae 12 CONGRATULATI
8. ONS on your recent selection of a State of the art Cone Art Kiln Offering excellence in unparalleled design and craftsmanship Cone Art kilns are built with the highest quality materials and attention to detail resulting in the best line of electric kilns on the market Please read all provided instruction manuals carefully and thoroughly before initial set up and operation the information contained herein will aid you in operating your Cone Art kiln safely and with excellent results Instruction manuals have been provided for all optional kiln instrumentation If you have any questions regarding the operation of your kiln contact us directly at Cone Art Kilns Inc 1 800 304 6185 or contact your dealer We trust you will enjoy many years of professional results from your Cone Art kiln Kiln Set Up Check Kiln for Damage Upon Delivery Every Cone Art kiln is inspected at the warehouse prior to shipment and carefully packed to prevent damage in transit We do recommend however checking for damage that may have occurred in transit When unpacking the kiln if damage is discovered follow these steps 1 Save all packaging 2 Call your freight carrier and ask for an inspection 3 Notify the dealer who sold you the kiln that you have found damage and have called the freight carrier for an inspection 4 DO NOT disassemble or fire the kiln until the damage claim is inspected and resolved Selecting the Best Kiln Location It is esse
9. fficient to carry the amperage demands of the kiln if in doubt we suggest consulting your electrician as this is a potential fire hazard situation 2 Ensure breaker size and or fuse rating exceeds kiln requirements breaker fuses may be too small causing an overload a qualified electrician should install correct breaker fuses 3 Check if other equipment appliances are operating on the same circuit potentially causing an overload 4 Inspect the power cord for loose connections or frayed wiring 5 Inspect the control box for signs of heat damage and loose or frayed wiring and or connections 6 Consult an electrician if the breaker continues to trip or fuses are continually blown Abnormally Long Firing Time 1 Confirm that the voltage of the power source matches kiln requirements 2 If kiln is operated on 240V service check fuses or circuit breaker one of the two circuit breakers may have tripped or one of the two fuses may have blown if so replace fuses or reset breaker if fuses continue to blow or breaker continues to trip consult an electrician 3 One or two components may have burned out analyze whether it is a heating element relay switch wire or connector Check if the heating elements are damaged or separated check the control box for burnt discoloured loose or broken wires or connectors Finally inspect the relays and switches for damage replace any damaged components 4 Elements gradually age and need replaci
10. ll heating elements are set into their grooves Kiln Wash or shelf primer is a coating which it used on all surfaces that glass may come into contact with such as shelves or molds It is normally supplied dry and must be mixed with water Consult your supplier for detailed instructions regarding application of kiln wash Fumes are a natural part of any kiln firing therefore for your health and safety we strongly recommend that you install a kiln vent to exhaust fumes even in a well ventilated area Connect kiln to power supply 10 Read all safety precautions in the next section before proceeding to test fire your kiln Important Safety Precautions CAUTION Your kiln is a device that produces extreme heat To prevent personal injury and or potential fire hazards read and follow these safety tips prior to initial kiln operation and EVERY subsequent kiln firing 1 Read all provided instruction manuals carefully and thoroughly before initial operation of your kiln as these manuals contain very important information Instruction manuals have been provided for all kiln instrumentation Before servicing your kiln always disconnect it from the power supply Do not touch exposed electrical contacts while connected to a power source 4 Do not stand in moisture while operating kiln and or working with electronic devices Never use an extension cord with your kiln Keep all types of flammable materials plastic drapes aprons etc a
11. lock Remove old thermocouple Install new thermocouple ensure that the red lead is placed in the NEGATIVE receptacle Replace the two centre screws of the thermocouple block Replace the thermocouple and block in the kiln Turn on the power supply and confirm that the new thermocouple works properly by observing the temperature readout as elements become hot Appendix D Switch or Relay Replacement Occasionally you may need to replace a switch or relay in order for your kiln to function To Install a New Switch l SS ee tae eee Confirm that the kiln is disconnected from the power supply by either unplugging from receptacle or disconnecting at breaker box Remove the knob from the switch this may require a small straight blade screwdriver Remove the screws on the right side of the control box panel and set aside Pull the control box panel open Each switch has multiple wires with masking tape label the damaged switch s wires and remove Unscrew the switch nut on the front of the control box panel remove the old switch Put the new switch in place and tighten the switch nut Re connect the wires marked with masking tape to the new switch Close the control box panel replace the screws and switch knob Turn on the power and confirm that the new switch works properly by noting that the element is glowing and emitting a humming sound To Install a New Relay l 2 3 PR Confirm that the kiln 1s disc
12. ls carry 14 gauge thermocouples Either type may be used with the Cone Art pyrometer The following are steps for replacing both types Replacing Thermocouple s in a Bartlett Automatic Controller l 2 3 ee So a Confirm that the kiln is disconnected from the power supply by either unplugging from receptacle or disconnecting at breaker box Remove the screws on the right side of the control box panel and set aside pull the control box open Unscrew two screws on the outer edges securing thermocouple block to the kiln Gently pull out thermocouple and block BE SURE KILN IS COLD BEFORE DOING THIS Unscrew the two centre screws holding down thermocouple Remove old thermocouple Install new thermocouple ensure that the red leg is placed in the NEGATIVE receptacle Replace and tighten screws Thread thermocouple into kiln though brick Re attach thermocouple block to kiln with two outer screws Close the control box panel replace the panel screws Turn on the power supply and confirm that the new thermocouple works properly by observing the temperature readout as elements become hot Replacing the Thermocouple in the Cone Art Pyrometer l Confirm that the kiln is disconnected from the power supply by either unplugging from receptacle or disconnecting at breaker box N Se Remove the thermocouple block from the kiln BE SURE KILN IS COLD BEFORE DOING THIS Unscrew the two centre screws of the thermocouple b
13. ng element life span varies greatly with element size as well as temperature and atmosphere to which you are firing so check regularly see Appendix B for element replacement instructions 5 Check if other equipment appliances are operating on the same circuit potentially causing a power drain One Section of Kiln is Hotter than Normal Check switches or relays for any visible signs of heat damage that may be forcing a switch or relay to continuously send power to the elements causing a section to overheat 7 One Section of Kiln is Cooler than Normal 1 One or two components may have burned out analyze whether it is a heating element relay switch wire or connector Check if the heating elements are damaged or separated check the control box for burnt discoloured loose or broken wire or connectors Finally inspect the relays and switches for damage replace any damaged components 2 Elements gradually age and need replacing element life span varies greatly with element size as well as temperature and atmosphere to which you are firing so check regularly see Appendix B for element replacement instructions There are Cracks in the Kiln Lid and or Floor Bricks 1 Hairline cracks in the lid and kiln floor are common and often occur during the first few firings as a result of the bricks expanding and contracting 2 These cracks will not affect the firing and it is best not to try and repair them as repair cement will usually shrink
14. ng firing It will also allow you to become familiar with the operation of your kiln For a kiln with switches turn the switches gradually until the kiln reaches 1500 F For a kiln equipped with a controller programme the kiln to go up to 1500 F over 3 or 4 hours Refer to controller manuals for instructions Loading The Kiln Always use a kiln shelf when firing This is important even if the glass is being placed on a mold It is much better to ruin a shelf than a kiln floor if problems arise Posts are used under the shelf for more even heat distribution Three posts per shelf is the most stable configuration It acts like a tri pod and the shelf will not rock Position the glass on the shelf or mold as desired Firing Instructions with manual switch Control The following is a very general outline For exact firing instructions for a particular type of glass please consult your supplier After loading the glass prop the lid open about 1 and open the peephole This allows fumes to escape Gradually turn your switches up until the kiln reaches 1000 F A good starting point is 30 minutes on a low setting 2 or 3 and then on a medium setting until 1000 F is reached Close the lid and peep holes Turn the switches to high and fire until the firing is complete Once you are satisfied with the results turn the kiln off and prop open the lid This is to ensure that the glass does not change any further Always use protective eyewea
15. ntial to select a safe clean and convenient location for your kiln in order to ensure long kiln life and avoid a potential fire Regulations about kiln placement vary we strongly recommend consulting your local government s ordinances codes to ensure safe and proper kiln location The following are general safety and convenience guidelines to consider 1 Ensure that the kiln is placed in a well ventilated area CAUTION DO NOT PLACE KILN IN A CLOSET OR CABINET it can overheat and potentially start a fire Any room such as a garage shed carport basement utility or hobby room is safe if it has SUFFICIENT CIRCULATING AIR even so we highly recommend installing a vent system to safely exhaust potentially harmful fumes 2 Set the kiln on a level and stable surface if the floor is not concrete it is essential that the kiln be placed on a non flammable surface such as firebrick or cement block 3 DO NOT EXPOSE YOUR KILN TO THE WEATHER CONDITIONS safe kiln operation requires your kiln to stay dry and clean ina sheltered yet well ventilated location 4 Locate kiln as close as possible to an existing or anticipated electrical outlet 5 Place your kiln at least 18 away from any flammable materials including walls drapery paper plastic cloth etc Unpack the Kiln NOTE jf you must disassemble the kiln to fit through a narrow doorway follow the kiln disassembly instructions contained in this manual refer to Appendix A 1 Ca
16. oller which allows for precise control of your firing Please read the manual for complete instructions 3 The Bartlett V6 Controller This is an automatic controller which has many more options which makes firing more precise and much more convenient Complete information is provided with the manual Preventive Kiln Maintenance Your Cone Art kiln will provide you with many years of use To prolong the life of the kiln and ensure error free operation it is necessary to perform regular maintenance on your kiln and kiln instrumentation We suggest the following 1 Inspect and vacuum element grooves regularly dust and other debris not removed will eventually damage the elements 2 Check the lid and remove any brick particles 3 Shelves may need a new layer of kiln wash Occasionally old kiln wash must be completely removed with a scraper and wire brush and a new layer of kiln wash evenly re applied 4 If your kiln is equipped with a Bartlett automatic controller check the thermocouples before every firing and replace them if they appear thin or corroded approximately every 30 firings If it breaks during a firing the safety system will automatically shut off the kiln resulting in an interrupted firing and potential ware damage 5 Regularly check for elements that are popping out of the grooves careful elements are very brittle when cold To repair a popped element heat the element until it is glowing orange shut off the kiln
17. onnected from the power supply by either unplugging from receptacle or disconnecting at breaker box Remove the screws on the right side of the control box panel and set aside Pull the control box panel open Each relay has multiple wires Plug each wire one at a time onto new relay DIRECTLY as you pull off from old relay Unscrew the two side screws holding old relay in place replace with new relay and tighten in to place Close the control box panel replace the screws Turn on the power and confirm that the new relay works properly by noting that the element is glowing and the relay is emitting a clicking sound 10 LIMITED WARRANTY What does this Warranty cover This warranty covers any defect or malfunctions in your new Cone Art kiln that affect the performance of you new Cone Art kiln How long does the coverage last The coverage of this warranty lasts for two years from the date of purchase What does this Warranty not cover This warranty does not cover the pyrometer and heating elements In addition any problem that is caused by abuse misuse such as overriding or not operating the kiln in accordance with the printed instructions provided with the kiln vandalism or an act of God such as a fire or flood are not covered Incidental and consequential damages are not covered Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply
18. r gloves and clothing when firing the kiln When the kiln cools to 1000 F close the lid The temperature will rise again This is normal If you think the temperature has gone up too much prop open the lid again until it cools again to 1000 F Fully close the lid and anneal the glass to the temperature supplied by the glass supplier If you are not sure go slow An annealing rate of between 60 F and 100 F per hour is a good rule of thumb Once the kiln has cooled below the annealing range as suggested by your glass supplier turn the kiln off When the kiln reaches room temperature the glass can be safely removed Firing with an Automatic Controller Proceed using the instructions provided above Program your controller with the desired firing schedule As the firing proceeds check the controller to make sure it is firing the kiln as you specified Please refer to your controller manual for exact programming instructions Types of Controllers Your kiln can be supplied in one of these ways 1 Infinite Switch A kiln to be manually operated comes equipped with one or more infinite switches The higher the position the more time the switch will be on For example on a low sitting the switch may be on 20 off the time and off 80 of the time On high the switch will be on 100 of the time This type of switch is often used in conjunction with a pyrometer which measures temperature 2 Bartlett 3 button controller This is an automatic contr
19. refully cut and remove the metal strapping that attaches the stand to the top of the kiln 2 Lift kiln stand out of the box and set in the location designated for the kiln refer to Selecting the Best Kiln Location section of this manual 3 Confirm that the stand is level and does not teeter as an uneven stand is a safety hazard and may put stress on the kiln during firing if stand is not level place firm shims under the kiln stand legs until stand is level 4 With a partner lift the kiln using the exterior kiln handles when present and place it securely and evenly on the kiln stand Larger kilns may best be moved in sections Ensure that Kiln s Electrical requirements match building s Electrical Service 1 It is essential that your kiln s electrical requirements are compatible to your building s electrical service factors to consider include voltage amperage and phase For example if the kiln will be placed in a building that is wired for 240V you will want a kiln that is wired for 240V If the kiln will be placed in a building that has 208V you will want to purchase a kiln wired for 208V CAUTION If you are in doubt about the compatibility of the kiln you purchased and your building s electrical service we strongly recommend consulting an electrician as an incompatible instalment will not allow the kiln to operate properly 2 3 With the exception of our 120V models the Canadian Standards Association C S
20. way from the kiln Do not expose your kiln to the weather conditions safe kiln operation requires your kiln to stay dry and clean 8 NEVER FIRE THE KILN UNATTENDED 9 Do not attempt to exceed the temperature rating listed on the nameplate of the kiln 10 Observe caution when firing your kiln as the kiln surface will become very hot keep children away from kiln and alert others when firing 11 Never open the kiln unless you know it is cool STOPES Test Firing You are now ready to proceed with a test firing it is imperative that you complete this properly BEFORE proceeding to production firing Prior to the test firing check electrical connections and read all provided instruction manuals carefully and thoroughly as they contain vital information on safe kiln operation New kiln elements give off vapours therefore the test firing is performed with an empty kiln NOTE Do not be alarmed if there is excessive smoke created during test firing this is normal due to lubrication burning off the elements and starches burning out of the insulation A clicking sound is also normal while your kiln is firing the elements are switching on and off in order to reach the desired temperature gradually and evenly Initial Test Firing It is advisable to do a test firing with an empty kiln before firing your work It allows an aluminium oxide layer to build up on the elements which protects them from any corrosive fumes released duri
Download Pdf Manuals
Related Search