Label_MGP 464 _33-1390-01_revB
Contents
1. to select na to specify that Auto Image will not be performed Input Configuration Press Next to select the submenus for video signal format e g RGB Film Mode Vertical Start Horizontal Start Pixel Phases for windows 1 4 Total Pixels Active Pixels and Active Lines From each submenu rotate the horizontal Adjust knob lt gt to select the input to configure only inputs 1 4 can be configured via the front panel and the vertical Adjust knob to select a u value or parameter to apply to the selected input aed Output Configuration Press Next to select the submenus for Resolution and Refresh Rate Output Type e g RGBHV and Sync Polarity Rotate the MENU horizontal knob lt gt to select the required output resolution and the vertical 4 Adjust knob to select the refresh rate Turn either Adjust knob to select the Output output video type RGBHV RGBS RGsB YUV Bi level or YUV Tri level Use GB corner fi either Adjust knob to select positive or negative sync polarity for the horizontal and vertical sync MENU 4 Window Configuration Press Next to select submenus for Window Priority displayed in front or in back Border Color for windows 1 4 Window Effect Window transition effect while muting e g Dissolve or Cut and Effect Duration Rotate 20 sec either Adjust knob to select options from each submenu seni Background Capture Press Next to save the currently displayed image as2. 4 background for the windows Turn either Adjust knob to select a name for the new background file Press Next to save the image then Detail to confirm To recall an ore existing background image file to display press Next twice 6 Capture 20 B60 Communication IP Configuration Press Next to view the serial communication MENU RS 232 422 port configuration and the MGP s IP address 4 Advanced configuration Press Next to select the following submenus Background Color Rotate either Adjust knob to select a background color for 6 Configuration the output screen MENU Blue Mode Use either Adjust knob to enable or disable Blue Mode which 4 allows only sync and blue video signals to be sent to the display for setup Ad a vancec EEREN purposes 7 Configuration 20 sec Test Patterns Rotate either Adjust knob to select a test pattern to adjust the display MENU Internal Temperature View the unit s current internal temperature in degrees u Fahrenheit and Celsius MENU gt Press Next 20 sec Factory Default Press Detail to reset the unit to the default settings from the 8 factory Exit Menu Press Next to exit the menu system and return to the default cycle NEXT LISTED Executive Mode FE CON 1 To prevent accidental changes to settings executive mode locks all panel controls except Freeze input selection Preset Recall Save and the RS 232 422 and Ethernet ports To enable disable executive mo
3. MGP 464 and MGP 464W Multi Graphic Processors Installation 1 Install the four rubber feet on the bottom of the MGP or rack S video and mount the unit with the provided brackets For rack mounting Composite Component Composite remove the self adhesive rubber feet if they have been attached Refer to chapter 2 Installation and Operation in your MGP user s manual 2 Turn off power to the input and output devices and remove the power cords from them Connect the input sources to the MGP s BNC and or DVI input connectors The inputs can accept the following signal types RGB HD VIDEO INPUTS 1 2 3 and 4 RGB component video S video or composite video fully configurable DVI Background input DVI for live background video only RGBHV 1 RGBSor 1 RGsBor i Video RGBevS Component eins nalog is not available DVI BACKGROUND py Video on this DVI I connector y 9 h Attach one or two displays or other output devices to the on CS an oy MGP s output connectors XK J BNCs for RGBHV RGBS RGsB or YUV HD component S Ey video output B Y AR 1 Composite X X a BY L X X 29 0 W DVI I inputs 1 2 3 and 4 DVI MGP 464 DI and MGP 464W DI RGsB HD YUV Component Video models only DVI output DVI OUTPUT INPUT 1 DVI D INPUT 2 DVI D INPUT 3 DVI D INPUT 4 DVI D A l P t il bl ETA ee ETA ETA nalog IS not avallabie Ge
4. a Je Emese ien sje Beag NOTE on this DVERGonneciok MA Analog is not available on these DVI I connectors lf the MGP 464 will be connected to a computer or to a host controller for remote control connect the host s RS 232 cable to the MGP s 9 pin RS 232 422 D connector and or use an RJ 45 network cable to connect the MGP s LAN port to a network Refer to your MGP user s manual for instructions e Virtual inputs 5 19 Non WindoWall models only Component video S video or composite video configurable via Windows based control software SIS commands or Web pages only See the illustration at top right Plug the MGP and the input and output devices into a grounded In each column inputs can be connected as follows AC source and turn on the input and output devices o Thres composite video inputs Non WindoWall models Use the LCD menu screens see o One interlaced component video input Connects to all Menus at right SIS commands the MGP 464 Web pages or three BNCs in the column the Windows based control software to configure the MGP Refer o One S video input and one composite video input to chapters 3 4 and 5 of the MGP 464 User s Manual MA he S video must always be connected to the top WindoWall models Use the WindoWall Console software to two BNCs Y on top C second A composite video configure the MGP Refer to chapter 3 of the MGP 464W User s input can be connected t
5. de press the Window Image Size and Window Image Position buttons simultaneously and hold them down for 2 seconds non WindoWall models only Extron Electronics USA Extron Electronics Europe Extron Electronics Asia Extron Electronics Japan 1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Rd 04 01 Kyodo Building 16 Ichibancho Anaheim CA 92805 3821 AH Amersfoort The Netherlands PM Industrial Bldg Singapore 368363 Chiyoda ku Tokyo 102 0082 33 1390 01 Mune 800 633 9876 714 491 1500 800 3987 6673 31 33 453 4040 800 7339 8766 65 6383 4400 Japan Rev B www extron com FAX 714 491 1517 FAX 31 33 453 4050 FAX 65 6383 4664 81 3 3511 7655 FAX 81 3 3511 7656 06 08
6. o the bottom BNC Manual Front Panel Buttons The MGP 464 front panel non WindoWall models only contains the following sets of buttons that let you control and configure the processor Freeze Freeze the input in the currently selected window To unfreeze the input press the button again RGB HD Video Inputs 1 4 Select fully configurable inputs 1 4 On the MGP 464 DI these buttons can also select the four DVI inputs To mute turn off the input in a window press its button twice or once if the button is already lit The button flashes while the input is muted Virtual Video Inputs 5 19 Select inputs 5 19 These inputs can be configured to accept S video composite video or standard definition component video only Window selection Select a window to freeze unfreeze mute unmute select an input or to adjust using Picture Control buttons Preset Recall Save and Enter Save the current configuration settings preset to memory or recall a stored preset 128 presets are available To save the current settings as a preset press and hold the Preset Recall Save button for 2 seconds Rotate either Adjust knob to select a preset number then press Enter To recall a preset press and release the Preset Recall Save button Rotate either Adjust knob to select a preset to recall then press Enter Picture control Adjust window and image size brightness range of dark and light values contrast detail sharpness posi
7. tion color tint and zoom magnify reduce Use the horizontal lt gt and vertical Adjust knobs to adjust the picture settings shown on the left and right sides of the LCD screen respectively The MGP 464 s menu system non WindoWall models only enables you to configure the MGP by pressing buttons on the front panel Press the Menu button to move through the menus listed below From the displayed menu press the Next button to move through its submenus For each submenu rotate the horizontal lt gt and vertical Adjust knobs to make selections Refer to your MGP 464 User s Manual for further information on MGP menus and control buttons Mea f you press the Menu button while a submenu is active the display returns to the beginning of that menu and the menu s title the Main menu item is Extron f i MGP 464 V1 00 displayed For example if you press Menu while Resolution Refresh a submenu of the Output Configuration menu is active the display returns to the Output Configuration screen 2 sec Alea 70 return to the default cycle let the MGP 464 remain idle until the selected screen times out about 20 seconds or press the Menu button repeatedly until the Exit Menu appears then press the Next button O Auto Image Automatically sizes centers and optimizes the image to the scaled output rate filling the window Rotate either Adjust knob to select a window on which the Auto Image function will be performed or
Download Pdf Manuals
Related Search