User Manual
Contents
1. New PIN Green light comes ON when the pin has been changed Sound and Light Settings Light and Sound Setting Note The below changes can only be done while in programming mode To set keypad backlight To disable keypad backlight To enable keypad backlight Factory default To enable the red led light Factory default H H o Exi To set top light To disable the red light o Exi H To set keypad To disable the keypad tone tone m gt To enable the keypad tone Factory default to Exit Keypad Lockout Note The below changes can only be done while in programming mode If there are 10 incorrect Pin entered in a 10 minute period the keypad will go into a lock out mode for 120 minutes This feature is disabled by factory default Keypad Lockout To disable keypad lockout Factory default To enable keypad lockout to Exit Programming to PentaCode Receiver The PCKeypad will work with all of Elsema s PentaCode series receivers There are 2 methods of programming the Keypad to the receiver 12 Way Dip Switch Coding Remove the back cover of the keypad using the supplied screwdriver Match the 12 way dip switch to the recei2. PIN is any 4 8 digits with the exception of 1234 which is reserved Users can be added continuously without existing from programming mode as follows 1 User ID No PIN User ID No 2 PIN to Exit Press FF Delete a user Orange light confirms you are in delete mode Green light flash indicates a user has been deleted 2 User ID number Users can be deleted continuously without existing programming mode Press H Delete All users Warning This option will delete all user s to Exit 2 0000 Orange light confirms you are in delete mode Green light flash indicates all users have been deleted Change transmission time 4 1 90 Press to Exit Default is 5 sec Orange light confirms you are in time change mode Green light flash indicates that time has been changed Note The below changes can only be done while out of programming mode To activate the built in PentaCode transmitter PIN Green light comes ON for the transmission time Change a user s PIN Red light ON confirms you are in User Change mode New PIN ID Number Old PIN
3. User Manual PCKeypad Wireless Keypad ELSEMA Automatic Gate amp Door Technology Description The PCKeypad is a wireless keypad with a PentaCode transmitter built in It works with all of Elsema s PCR series receivers The installer has the option to use the classic 12 way dip switch coding or one of over 17 billion encrypted codes Please refer to the programming instructions The PCKeypad is suitable for mounting either indoor or outdoor environments It is housed in a strong vandal proof zinc alloy electroplated case The PCKeypad conforms to Ingress Protection 65 The PCKeypad supports up to 2000 users with 4 to 8 digit PIN These features make PCKeypad an ideal choice for gate and door access for homes shops factories warehouses laboratories banks and prisons Features gt gt gt gt gt gt gt gt gt gt gt gt Built in PentaCode transmitter Easy programming 12 24 VDC or 12 18 VAC Long operating range Strong zinc alloy electroplated anti vandal case All programming is done from the keypad 2 000 users PIN length 4 to 8 digits Adjustable transmission time Keypad has a backlight Built in light dependent resistor LDR for anti tamper Built in buzzer Red yellow and green LED display the working status Installation Remove the back cover from the keypad using the supplied security screwdriver Code the transmitter to the receiver prior to mounting the Keypad Dr
4. ill 4 holes on the wall for the screws and 1 hole for the cable Fix the back firmly on the wall with 4 flat head screws Thread the cable though the cable hole Attach the keypad to the back cover Specifications Operating Voltage 12 to 24 VDC or 12 to 18 VAC User Capacity 2 000 Active Current 65mA Idle Current 35mA Operating 20 C 50 C Temperature Operating Humidity 10 90 RH Adjustable 1 90 seconds Transmission Time Operating Range Up to 50 metres with line of sight Dimensions 128 x 82 X 28mm Weight 700g Wire Colour Function Red AC or DC Supply for DC Black AC or DC Supply for DC Green Wiegand 26 Bit Output DO White Wiegand 26 Bit Output D1 Blue Wiegand Ground GND Anti Tamper Alarm The PCKeypad uses a built in LDR light dependent resistor as an anti tamper alarm If the keypad is removed from the cover then the internal buzzer starts beeping for 1 minute Reset to the Factory Default To reset the Keypad to the factory default follow the steps below Disconnect the power of the unit Press and hold the key Reconnect power to the unit Release the key after you hear 2 beeps The LED will turn amber for a few seconds and then change to flashing red with one beep This indicates a successful reset Programmed user ID and user PIN is retained even after factory reset Transmission time The transmission time of
5. the built in PentaCode transmitter is adjustable from 1 to 90 seconds Factory default is 5 sec See Programming Guide to change Sound and Light Indication Operation Status Red Light Green Light Yellow Light Buzzer Power on Bright Short Ring Stand by Bright Press keypad Short Ring Operation successful Short Ring Operation failed 3 Short Ring Enter into programming Short Ring mode In programming mode Short Ring Exist from the Short Ring programming mode Open the door Short Ring Alarm Short Ring Programming Guide Enter Programming Mode One beep green light flashes once red light On to confirm you are in programming mode Master code 888888 is the factory default master code After 1min with no button pressed keypad will exit programming mode Exist from the programming mode Pk Exit is confirmed with flashing red light Note The below changes can only be done while in programming mode Change the master code Orange light confirms you are in change mode 0 New code New code The master code must be 6 digits long Add a user Orange light confirms you are in adding mode Green light flash indicates a user has been added A user ID number PIN ID number can be between 1 2000 The
6. vers 12 way dip switch DO NOT USE THE DEFAULT FACTORY SETTING FOR THE 12 WAY DIP SWITCH AS THIS IS A COMMON CODE Test the keypad by typing in a valid user pin code Encrypted Coding All 12 Way Dip Switches must be Off 1 Make sure that all 12 way dip switches are Off 2 Type in a valid user code the transmitter will transmit for 5 second default 3 With in the 5 second or while the transmitter is transmitting press the program 1 button on the receiver for 1 second Keep records of who is using the ID Numbers and Pins This makes future additions and maintained easy Keep this document in a secure and safe place User ID Name of User Pin Number Use Microsoft Excel to create a longer list 2000 User ID numbers can be added Visit www elsema com to see our full range of Gate and Door Automation Products
Download Pdf Manuals
Related Search