User Manual
Contents
1. NSR soLe Rechargeable Handheld Callus Remover User Manual Thank you for purchasing the ANSR SOLE Please read and observe all warnings and instructions in this manual prior to use and retain for future reference 1 Main Body 5 Cover 2 Debris Container 6 Charger 3 Polishing Plate 7 Instruction Manual 4 Silicon Guard Ring y IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this device ONOARWDNDM N 9 O1 PW WARNING Follow these instructions to reduce risk of electrical shock If device is submerged into water unplug immediately do not use Do not place or store device while plugged in where it can fall and be submerged in water Do not place or drop into water or another liquid while plugged in Always unplug device from electrical outlet after charging Unplug device before cleaning Do not dismantle battery place under water or put in fire Do not touch battery with wet hands and do not apply shock or damage the battery Do not touch positive and negative socket to other metals Follow these instructions to reduce risk of burns fire electrical shock or injury to persons Not intended for use by on or near children Do not operate device if it has a damaged cord or plug if it is not working properly if it has been dropped or damaged or submerged in water Callus remover is only intended for use as stated in this manual Do not use any attachment not mentioned in this manua2. Keep cover closed at all times unless charging Silicon Cover How to Use ONOARWDND o Remove cover and press button once to power on Move the device around on foot to remove callus Do not use on a single area Use up to 10 minutes at once and only 30 minutes a day Press button once to stop motor Remove Guard Ring by turning clockwise Lift the plate up to separate from the main body Lift the debris container to separate from the main body Discard contents from the debris container by turning upside down and tapping lightly Wash out debris container with water and dry Refer to assembly directions of page 5 Directions for Cleaning BON Remove cover silicon guard ring polishing plate and debris container from main body of device Discard contents from the debris container by turning upside down and tapping lightly Rinse removed components with water and dry thoroughly Lightly wash the surface around the motor shaft Keep water from seeping into jack and power button Grip as shown below while cleaning covering power button with hand Keep silicon lid tightly closed to prevent water or other debris from getting in 1 In order to effectively remove callus adjust the speed and pressure of polishing place depending on the condition of the callused skin When the plate is rotating apply pressure to reduce its speed and increase force Move the plate around the callus and surrounding skin Do not keep on o
3. l Keep cord plug and device away from heat sources Do not use callus remover while plugged into charger or electrical outlet eo Do not attempt to Do not use device within Do not touch any part of the dismantle the device 50cm 20in of your face charger with wet hands X ONOOaARWDND 11 12 13 14 15 16 17 Stop using product immediately if you feel pain Do not touch motor or polishing plate while in operation Stop using product if you hear unusual noise Stop using product if the main body is hot Keep device at least 50cm 20in from face while in operation Do not allow debris to get into eyes nose mouth or ears Do not use device if you have a nail or skin disease Consult your physician prior to use if you have extremely thick calluses dermatitis or blood circulation disorder Wipe this product with a dry cloth Do not use any cleaning agents such as benzene or alcohol When using device lay down towel or mat as debris may be scattered Store this product in a dry area with all components well dried Do not drop device This may lead to damage breakage or malfunction While in operation do not concentrate polishing plate to any one area of the foot as this may generate frictional heat pain or wounds Do not use more than 10 minutes at a time or 30 minutes a day Before use make sure polishing plate is in normal condition Any malfunction distortion or damage may lead to injury Do no
4. ne specific area Recommended Procedure a Soak feet in warm water for 10 minutes to soften skin b Exfoliate with device c Rinse feet d Apply lotion to the skin after removal to increase effectiveness BON Polishing plate is a consumable part If callus removing ability becomes decreased replace polishing plate Design or components are subject to redesign to improve performance or convenience without notice The device is shipped with all components attached to main body Familiarize yourself with all components and how to disassemble assemble the devise prior to use Product Specifications Charger Input Voltage 100 240Vac Charger Input Frequency 50 60Hz Charger Output 4 2V 600mA Main Body s Rated Voltage 3 6V Ni MH battery Dimension of the Main Body cm 6 0x17 5x6 0 width x height x depth inch 2 4x6 9x2 4 width x height x depth For additional information about this product or questions regarding problems during use contact 1 800 890 8373 Warranty Exceptions 1 Damage to product or parts caused by misuse abuse negligence or unauthorized alteration 2 General wear and tear including splitting scratches wear out and or discoloration Product Warranty 1 We warrant this product to be free from defect in material and workmanship for a period of one 1 year 2 n order to receive service during this period you must provide proof of purchase i e receipt with purchase item and date produc
5. t push too forcefully to stop polishing plate Stopping of plate during use may overload and cause malfunction Remove device from charger after the battery is fully charged Read instructions on how to disassemble and assemble parts before use How to Disassemble 1 Open cover El 2 Turn guard ring clockwise to detach it from the main body BJ 3 Lift the polishing plate up to detach it from the callus debris container amp 4 Lift up on the debris container to detach it from the main body El How to Assemble 1 Connect debris container to the main body s motor shaft When connecting to the motor shaft check for proper direction and move downwards to connect Do not attempt to connect forcefully this may cause misalignment or separation of magnet 2 Connect the polishing plate to the debris container 3 Match the circular protrusion of the main body with that of the guard ring and turn ring counter clockwise for connection to the main body 4 Close cover N NO oR o Fully charge battery before using the device for the first time A red light indicates the charger is connected to an electrical outlet and the jack located on the device A green light indicates the device is fully charged Remove device from charger before use To charge fully plug in device for 3 4 hours Do not charge for longer than 5 hours The product must be turned off to charge properly Re cover the jack on the bottom with silicon cover
6. t warranty card indicating the service reguest date is within the warranty period 3 The polishing plate is not covered under warranty due to normal wear nn Visit www ANSR com warranty to register your product Or complete the warranty registration information on this page detach and mail with copy of receipt of purchase to ANSR SOLE Warranty Registration PO BOX 10087 Portland OR 97296 Product Name Model Name Date of Purchase Purchased From Name of Purchaser Address Telephone Email How did you become aware of the ANSR SOLE Please include me on your email list O YES Ll NO
Download Pdf Manuals
Related Search