TR-LCD1900-OCD User`s Manual
Contents
1. 020 108 00 VESA 1280 x 1024 79 976 75 025 135 00 SUN 1280 x 1024 81 129 76 106 135 00 Horizontal Freguency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency Unit kHz Vertical Frequency Like a fluorescent lamp the screen has to repeat the same image many times per second to display an image to the user The frequency of this repetition is called Vertical Frequency or Refresh Rate Unit Hz 11 TR LCD1900 OCD User Manual TRANSDUCTION 5155 Spectrum Way Bldg 23 Mississauga ON L4W 5A1 Canada 905 625 1907 www transduction com TR LCD1900 OCD User Manual 19 LCD MONITOR ON OFF SWITCH BUTTON MONITOR CONTROL BUTTONS MONITOR ON LED 15 000 17 750 FRONT VIEW 07 03 2009 BG TR LCD1900 0CD PM PANEL MOUNT VERSION ISH CRINKLE BLACK POWDER PAINT DETACHABLE POWER SUPPLY M e III UK OPTIONAL e e e e e USB PORT FOR TOUCH SCREEN COMPOSITE VIDEO INPUT 12VDC INPUT DVI INPUT ANALOG RGB REAR VIEW PANEL MOUNT VERSION VGA INPUT REAR TE Tansauction 7777 DETACHABLE POWER SUPPLY RIGHT SIDE VIEW 07 03 2009 TR LCD1900 0CD PM PANEL MOUNT VERSION NOTE FOR DETAIL A LOOK DRAWING B 441 97 03 2009 TR LCD1900 0CD PM PANEL MOUNT VERSION IN2. signal a message appears on the screen or the screen goes blank The message may indicate that the monitor is out of scan range or that you need to check the signal cable Video mode not supported Useful Tips e Amonitor recreates visual signals received from the PC Therefore if there is trouble with the PC or the video card this can cause the monitor to become blank have poor coloring noise Video mode not supported etc e Judging the monitor s working condition If there is no image on the screen or Video mode not supported message comes up discon nect the cable from the computer while the monitor is still powered on If there is message coming up on the screen the screen goes white this means the monitor is in working condition this case check the computer for trouble 9 TR LCD1900 OCD User Manual TR LCD1900 OCD Specifications TR LCD1900 OCD Monitor Notes LCD Module Active matrix thin film transistor Size 19 0 inch diagonal TFT liquid crystal display Display Area 376 32 H x 301 056 V LCD Pixel Pitch 0 294 H x 0 294 V Type a si TFT active matrix Viewing Angle 80 H 75 Brightness 300 cd m Contrast Ratio 700 1 Synchronization Horizontal 30 81 kHz Automatically Vertical 56 75 Hz Automaticall Display Colors Dependent on display card Analog input 16 194 277 used Resolution See Other Resolutions Optimum resolution 1280 x 1024 60Hz Supported on page 11 f
3. I CHECKED B NTS UTrensauction 747 MONITOR ENCLOSURE CHD PANEL FRONT BEZEL NOTE CLIP ATTACHED FROM BEHIND AFTER CHASSIS PLACEMENT IN THE PANEL OPENING 2 O O LC r LC 19 LCD MONITOR 18 960 FRONT VIEW E SCALE Busano Transouction S B 442 DETACHABLE POWER SUPPLY I III OPTIONAL USB PORT FOR TOUCH SCREEN gt O O LC LC T COMPOSITE VIDEO INPUT 12VDC INPUT DVI INPUT ANALOG RGB REAR VIEW saan NTS VGA INPUT Tarsaucton 15 750 9U DETACHABLE POWER SUPPLY 07 03 2009 TR LCD1900 OCD RM mes rackmount version FINISH CRINKLE BLACK CHECKED BY N LAYOUT B 444 48VDC 24VDC INPUT TERMINAL BLOCKS DVI INPUT S VIDEO INPUT COMPOSITE VIDEO INPUT 12VDC INPUT ANALOG RGB VGA INPUT USB PORT FOR TOUCH SCREEN TR LCD1900 OCD PM RM FINISH NTS Transoauction TITLE DRAWING No CONNECTOR LAYOUT B 445
4. TRANSDUCTION USER S MANUAL Version 1 0 07 02 09 TR LCD1900 OCD 19 Rack Panel Mount TFT LCD Monitor with Front LCD Controls 5155 23 Spectrum Way Mississauga ON Canada L4W 5A1 TEL 1 800 268 0427 905 625 1907 F AX 905 625 0531 Email sales transduction com Important Information The information in this document is subject to change without notice All relevant issues have been considered in the preparation of this document Should you notice an omission or any guestionable item in this document please feel free to notify Transduction Regardless of the foregoing statement Transduction assumes no responsibility for any errors that may appear in this document nor for results obtained by the user as a result of using this product Copyright O 2009 Transduction All rights reserved This document is protected by copyright No part of this document may be reproduced copied or translated in any form or means without prior written permission from Transduction All other trademarks brand and product names are the property of their respective owners Return policy Products returned for repair must be accompanied by a Return Material Authorization RMA number obtained from Transduction prior to return Freight on all returned items must be prepaid by the customer The customer is responsible for any loss or damage caused by the carrier in transit To obtain an RMA number call us at 905 625 1907 We will need the following in
5. age 4 for further information regarding cable connections 6 TR LCD1900 OCD User Manual Troubleshooting Tips Symptom No images on the screen cannot turn on the monitor Check List Is the power cord connected properly Before calling for service check the information in this section to see if you can remedy any problems yourself If you do need assistance please contact Transduction Solutions Check the power cord connection and supply Can you see No Connection Check Signal Cable on the screen Connected using the D sub cable Check the signal cable connection Connected using the DVI cable If you still see an error message on the screen when the monitor is connected properly check to see if the monitor status is set to analogue Press Source button to have the monitor double check the input signal source If the power is on reboot the computer to see the initial screen the login screen which can be seen If the initial screen the login screen appears boot the computer in the applicable mode the safe mode for Windows ME 2000 XP and then change the frequency of the video card Refer to the Preset Display Modes page 32 Note If the initial screen the login screen does not appear contact a service center or your dealer Can you see Video mode not supported on the screen You can see this message when the signal from the video card exceeds the maximum resolution and
6. been set properly Set the video card by referring to the video card manual The screen suddenly has become unbalanced Have you changed the video card or the driver Adjust screen image position and size using the OSD or MagicTune Have you adjusted the resolution or frequency to the monitor Adjust the resolution and frequency at the video card Refer to the Preset Display Modes page 32 The screen can be unbalanced due t the OSD or MagicTune o the cycle of the video card signals Readjust Position by referring to The screen is out of focus or OSD cannot be adjusted Have you adjusted the resolution or frequency on the monitor Adjust the resolution and frequency of the video card Refer to the Preset Display Modes page 32 LED is blinking but no Is the frequency properly adjusted Adjust the frequency properly by referring to the video card manual and images on the screen when checking the Display Timing on the Preset Display Modes the menu The maximum frequency per resolution may differ from product to product There are only 16 colors Have the Windows colors been set For Windows ME 2000 XP shown on the screen The screen colors have changed after changing the video card properly Set the colors properly at the Control Panel Display Settings Has the video card been set Set the video card by referring to the video card manual properly There is a message t
7. formation Return company address and contract Model name model number and serial number e Description of the failure Mark the RMA number clearly on the outside of each box include a failure report and return the product to Transduction 5155 23 Spectrum Way Mississauga ON Canada LAW 5A1 Attn RMA Department Safety Precautions When not used for extended periods of time set your PC to DPMS If using a screen saver set it to the active screen mode Do not use a damaged or loose plug This may cause an electric shock or fire Do not pull the plug out by the wire or touch the plug with wet hands This may cause an electric shock or fire Use only a properly grounded plug or receptacle An improper ground may cause electric shock or equipment damage Do not excessively bend the plug and wire or place heavy objects on them This could cause damage and an electric shock or fire Do not place the monitor face down The CDT surface may be damaged When cleaning wipe with a slightly moistened soft cloth Do not spray any cleaner directly on to the monitor Do not remove housing No serviceable p arts inside Refer servicing to Trans duction 1 TR LCD1900 OCD User Manual Contents Your new TR LCD1900 OCD monitor box should contain the following Power Cord Video Signal Cable User s Manual and Driver Installation CD TR LCD1900 OCD rack mount panel mount monitor Remember to save your original box and packin
8. frequency that the monitor can properly handle Adjust the maximum resolution and frequency that the monitor can properly handle There is no image on the screen Is the power indicator on the monitor blinking at 1 second intervals The monitor is in PowerSaver mode Press a key on the keyboard or move the mouse to activate the monitor and restore the image on the screen If there is still no image press the Source button Then press any key on the keyboard or move the mouse again to activate the monitor and restore the image on the screen Connected using the DVI cable You may get a blank screen if you boot the system before you connect the DVI cable or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals Connect the DVI cable and then reboot the system I cannot see the On Screen Display Have you locked the On Screen Display OSD Menu to prevent changes Unlock the OSD by pressing the MENU button for at least 5 seconds The screen shows strange colors or just black and white Is the screen displaying only one color as if looking at the screen through cellophane paper Check the signal cable connection Make sure the video card is fully inserted in its slot Have the screen colors become strange after running a program or due to a crash between applications Reboot the computer Has the video card
9. g material to transport or ship the monitor Video Signal Cable TRANSDUCTION User s Manual and Driver Installation CD TR LCD1900 OCD User Manual Quick Start To attach the TR LCD1900 OCD monitor to your system follow these instructions 1 Turn off the power to your computer 2 Connect the power cord for your monitor to the power port on the back of the monitor Plug the power cord for the monitor into a nearby outlet 3 1 Using the D sub analog connector on the video card Connect the signal cable to the 15 pin D sub connector on the back of your monitor 3 2 Using the DVI digital connector on the video card Connect the DVI cable to the DVI port on the back of your monitor 4 Connect to a Macintosh Use the D sub connection cable An older model Macintosh may require a special Mac adaptor 5 Turn on your computer and monitor If your monitor displays an image inst allation is complete NOTES You may get a blank screen depending on the type of video card you are using if you connect simultaneously both D sub and DVI cables to one computer Ifthe monitor is connected properly using the DVI connector but you get a blank or fuzzy screen check to see if monitor status is set to analog Press Source button to have the monitor double check the input signal source 3 TR LCD1900 OCD User Manual Control Panel Buttons The Control Panel Buttons give various and very easy graphic user interface
10. g the adapter video driver boot the computer in Safe Mode remove the Display Adapter from the hardware profile and then reboot the computer and reinstall the adapter video driver Frequently Asked Questions How can change the frequency Question Answer How can adjust the resolution How can set the Power Saving function How can clean the outer case LCD Panel TR LCD1900 OCD User Manual Self Test Feature The TR LCD1900 OCD has a Self Test feature that allows you to check whether your monitor is functioning properly Self Test Feature Check 1 Turn off both your computer and the monitor 2 Unplug the video cable from the back of the computer 3 Turn on the monitor If the monitor is functioning properly you will see a box with a border and text inside as shown in the following illustration The three boxes inside the border are red green and blue No Connection Check Signal Cable Failure of any of the boxes to appear indicates a problem with your monitor This box also ap pears during normal operation if the video cable becomes disconnected or damaged 1 Turn off your monitor and reconnect the video cable then turn on both your computer and the monitor If your monitor remains blank after following the previous procedure check your video controller and computer system your monitor is functioning properly Warning Messages If there is something wrong with the input
11. hat reads Unrecognized monitor Plug amp Play VESA DDC monitor found Have you installed the monitor driver Install the monitor driver according to the Driver Installation Instructions See the video card manual to see if the Plug amp Play VESA DDC function can be supported Install the monitor driver according to the Driver Installation Instructions TR LCD1900 OCD User Manual Troubleshooting Tips Check Before Using MagicTune 1 2 The MagicTune display adjustment feature is not available in Game mode or Full Screen video mode When activated in a mode in which the four edges of the display are black Game or DOS mode the Auto feature of the LCD monitor may cause the screen to be displayed of f center Installing the MagicTune display adjustment software may cause a slight delay when starting the computer Check the following items if there is trouble with the monitor 1 2 Check if the power cord and the cable are properly connected to the computer Check if the computer beeps more than 3 times when booting If it does request an after service for the main board of the computer If you installed a new video card or if you assembled the PC check if you installed the adapter video driver Check if the scanning ratio of the video screen is set at 75Hz Do not exceed 60Hz when using the maximum resolution If you have problems in installin
12. ome black pixels could be seen This is normal For example the no of TFT LCD pixels that is contained in this product are 3 932 160 MagicTune Display Adjustment For Windows 98SE or later Feature Regulatory Approvals CSA CE UL FCC Class A Note Design and specifications are subject to change without prior notice 10 TR LCD1900 OCD User Manual Resolutions Supported If the signal transferred from the computer is the same as the following Preset Timing Modes the screen will be adjusted automatically However if the signal differs the screen may go blank while the power is on Refer to the video card manual and adjust the screen as follows Preset Timing Modes Display Mode Horizontal Vertical Pixel Clock Sync Polarity Frequency Frequency MHz H V kHz Hz IBM 640 x 350 31 469 70 086 25 175 IBM 640 x 480 31 469 59 940 25 175 720 400 31 469 70 087 28 322 640 480 35 000 66 667 30 240 832 624 49 726 74 551 57 284 VESA 640 x 480 37 500 75 000 31 500 VESA 640 x 480 37 861 72 809 31 500 VESA 800 x 600 35 156 56 250 36 000 VESA 800 x 600 37 879 60 317 40 000 VESA 800 x 600 46 875 75 000 49 500 VESA 800 x 600 48 077 72 188 50 000 VESA 1024 x 768 48 363 60 004 65 000 VESA 1024 x 768 56 476 70 069 75 000 VESA 1024 x 768 60 023 75 029 78 750 VESA 1280 x 1024 63 981 60
13. or Maximum resolution 1280 1024 75Hz complete list Input Signal Terminated RGB Analog DVI Compliant Digital RGB Composite H V Sync SOG option 0 7Vp p Positive at 75 ohms Separate H V sync TTL level positive or negative Maximum Pixel Clock 140 MHz Power Supply AC 90 264 VAC rms 60 50 Hz 3Hz or optional 12VDC input Power Consumption 42W Maximum Signal Cable 15pin to 15pin D sub cable detachable DVI D to DVI D connector detachable Dimensions W x D x H Weight Rack mount 18 96 x 2 875 x 15 75 90 14 3 Ib 48 16cm x 7 3cm x 40 01cm 6 5 kg Panel mount 17 75 x 3 00 x 15 25 14 Ib 45 09cm x 7 62cm x 41 70cm 6 35 kg Environmental Considerations Operating Temperature 32 F 122 F 0 C 50 C Humidity 10 80 non condensing Storage Temperature 4 F 140 F 20 C 60 C Humidity 5 95 non condensing Vibration amp Shock 5G 30G Plug and Play Capability This monitor can be installed on any Plug amp Play compatible system Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings In most cases monitor installation will proceed automatically unless the user wishes to select alternate settings Dot Acceptability TFT LCD panel is manufactured by using advanced semiconductor technology with precision of 99 999 above is used for this product But the RED GREEN BLUE and WHITE color pixels may seem to be bright sometimes or s
14. put source Sharpness Adjusts the sharpness of video image other than PC DVD VCR Color 6500 K Reddish white The color can be 9200 K Bluish white changed from User User customizable reddish to bluish white Setup Image H Position Adjusts the horizontal position of the image Setup is used to V Position Adjusts the vertical position of the image adjust OSD menu GAMMA Bypass information and Information Displays current display mode image OSD Language English Germany French Italy Spanish Color Changes the opaqueness of the OSD background Position Moves the OSD Window Duration Indicates time until the OSD Menu will disappear after adjusting the menu OSD Lock Avoids OSD control except HOT key Mode Changes the image information to factory outgoing status Recall Backlight Changes the brightness of image by controlling the backlight of panel Auto sleep Goes to soft power off after 10 minutes when input cable is disconnected TR LCD1900 OCD User Manual Rear Panel Connectors and On Off Switch The configuration at the back of the monitor may vary from product to product 1 Power port Connect the power cord for your monitor to the power port on the back of the monitor 2 DVI port Connect the DVI Cable to the DVI Port on the back of your Monitor 3 Signal port Connect the signal cable to the 15 pin D sub connector on the back of your monitor Note See Quick Start on p
15. s Users can easily access the function needed Be sure that your system power and LED is turned on before operating the keyboard Key Name and Function Key Name Description Power Turns ON OFF the system Menu Activates the OSD menu or goes to previous menu Auto When the OSD menu is off press more than 3 seconds Performs Auto adjustment function When the OSD menu is on Selects the highlighted icon that user wants Down Moves the highlight icon up to the function that user wants Up Moves the highlight icon down to the function that user wants Left Decreases the adjustment of the selected function Right Increases the adjustment of the selected function Source Selects the Input Signal among analog RGB Digital DVI CVBS and S VHS Accessing the menu system 1 With the OSD off push the Menu button to activate the main OSD menu 2 Use the Up or Down buttons to move from one function to another As you move from one icon to another the function name changes to reflect the function or group of functions represented by that icon Please refer to the following table for a complete list of all of the functions available for the driver board 3 Press the Set button once to activate the highlighted function use the Up or Down buttons to select the function 4 After selecting a function use the or buttons to make optimum adjustments The setting bar moves and the numeric value indicator changes to reflec
16. t your adjustments Note The numeric value indicator is provided as a point of reference only and has nothing to do with a real measurement 5 Press the Menu button once to return to the main menu to select another function or press twice to exit from the OSD 4 TR LCD1900 OCD User Manual Control Panel Buttons cont d OSD Adjustment Menus Sub menus Function Descriptions Adjustment PC Brightness Adjusts the brightness of video Adjustment is used Contrast Adjusts the contrast of video to fine tune and get Clock Removes the noises When frequency value is wrong the image the best image by has horizontal lines especially in 1 dot on and off removing noises Phase Removes the noises When phase value is wrong the image that creates has vertical lines especially in 1 dot on and off unstable images Auto Adjust Auto adjustment allows the monitor to self adjust to the with jitters and incoming video signal The value of phase frequency and shimmers position are adjusted automatically Adjustment DVI Contrast Adjusts the contrast of image This function is Brightness Adjusts the brightness of image active if you select a digital DVI source Adjustment Brightness Adjusts the brightness of video Video Contrast Adjusts the contrast of video This function is Color Changes the richness of color active if you select Tint Changes the tone of color an in
Download Pdf Manuals
Related Search