Home
User Manual - US Cellular
Contents
1. Operating your device may interfere with medical devices like hearing aids and pacemakers Please always keep them more than 20 centimeters away from such medical devices when they are turned on Turn your device off if necessary Consult a physician or the manufacturer of the medical device before using your device Be aware of the usage limitation when using your device at places such as oil warehouses or chemical factories where there are explosive gases or explosive products being processed Turn off your device if required The use of electronic transmitting devices is forbidden in aircrafts at petrol stations and in hospitals Please observe and obey all warning signs and switch off your device in these conditions Do not touch the inner antenna area if not necessary Otherwise it will affect your device s performance Store your device out of the reach of little children Your device may cause injury if used as a toy Do not touch the metallic parts of your device so as to avoid a burn when your device is working Using Your Device Please use original accessories or accessories that are authorized Using any unauthorized accessories may affect your device s performance and violate related national regulations about telecom terminals Avoid using your device near or inside metallic structures or establishments that can emit electromagnetic waves Otherwise it may influence signal reception Your device 1s not
2. Check the IP address to make sure your client can obtain an IP address and client automatically in the Internet protocol TCP IP properties Type the correct network key Wi Fi password when you connect to the device The client connected to the device Make sure your SIM card is available annot ac the Internet pr rte me Change the location to find a place with good signal Contact your service provider Cannot visit the web user interface Enter the correct address The default address is http 192 168 1 1 or configuration page http uscc hotspot Only use one network adapter in your PC Do not use any proxy server About the password Select Device Info on the LCD screen to check the SSID and Wi Fi connection password or check the label on the device to get them Select Device Info on the LCD screen to check the default login password or check the label on the device to get it If you changed the password and forgot the new password you need to restore the device to the factory default settings For more assistance please e Send E mail to mobile O zte com cn e Visit www ztedevice com e Call Service Hotline 1 888 944 9400 34 Confidential and Proprietary Information of ZTE CORPORATION
3. General Wireless Networks Advanced Connect uzing Ea Atheros ARSOO7LUG Wireless Network This connection uses the following items los Packet Scheduler ig Internet Protocol TCP IP Description Transmission Control Protocol internet Protocol The default Wide area network protocol that provides communication across diverse interconnected networks Show icon in notification area when connected Notify me when this connection has limited or no connectryity ZTE Unite II User Manual 4 Select these two items and then click OK to finish the configuration Internet Protocol TCP IP Properties Ps General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address Obtain DNS server address automatically Use the following DNS server addresses Connecting to Your Device l Za 6 Confidential and Proprietary Information of ZTE CORPORATION Power on your device It will take 1 2 minutes to power up Use your Wi Fi application on the client to search for available wireless networks ZTE Unite II User Manual LTE Wireless Webwork Connection Disable Yiew Available Wireless Networks Status Repair Bridge Connections Create
4. there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Disposal of Your Old Appliance O When this crossed out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002 96 EC All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health For this product s recycling information based on WEEE directive please send an e mail to weee zte com cn Confidential and Proprietary Information of ZTE CORPORATION 33 LTE ZTE Unite II User Manual Troubleshooting Cannot establish the W1 Fi Refresh network list and select the correct SSID connection between your device
5. Authentication NONE IPv6 Authentication NONE IPv User Name IPv4 Password IPv6 User Name IPv6 Password 5 Set SSID Configuration in the following figure and then click Next 12 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual LTE Quick Settings Previous Network Name 5SID USCC MF96U 2200 Broadcast Network Name SSID Enable Disable Service Set Identifier SSID is used to uniquely identify your WLAN If you enable Broadcast Network Name SSID the gateway will broadcast the SSID and other devices can detect and connect to it 6 Set Security Configuration in the following figure and then click Next Quick Settings Previous Security Mode WWPA2 AES PSK w Wi Fi Password sesseeees Display Password Encryption will keep your traffic from being unauthorized monitored and accessed select one encryption mode from the list and then set key and or algorithm for it 7 Show the configuration in the following figure Confidential and Proprietary Information of ZTE CORPORATION 13 LTE ZTE Unite II User Manual Quick Settings Previous Apply APN ettings Manual Profle Name usccinternet IPv4 APN usccinternet IPve APN usccinternet IPv User Name IPv6 User Name IPv Authentication NONE IPv6 Authentication NONE Network Name SS5ID USCC MF96U 2200 Broadcast Network Name SSID Enable Security Mode WPA2 AES PSK Make sure that all
6. File Sharing to set the sharing mode on the above page The default mode is USB 2 Connect the device to PC Tablet via USB cable 3 Goto My Computer of your PC Tablet to access all files in microSDHC card NOTE You can access microSDHC card via USB cable only in USB mode The web page of sharing microSDHC card will be disabled Sharing microSDHC Card via Web Browser Select File Sharing and then the microSDHC card page is shown as the following figure 28 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual LTE SD Card status SD Card already exists and can be used now Mode USB Full Share share Setting Enable Disable File to Share Entire SD Card Custom Access Type Read Write Read Only Path to Share Check Full Share mode Check Enable to enable share settings Set File to Share and Access Type Click Apply to save the settings Launch the Internet browser on your PC Tablet Smart phone connected to the device via Wi Fi and enter http 192 168 1 1 in the address bar Click View SD Card on the login window to access the files in microSDHC card Pe oe AS sa Password eView SD card Messages This function allows you to receive messages Operating Messages in Native You can check the messages saved in your device Device Messaging Select Messages gt Device Messaging to access the following figure Confidential and Proprietary Information of ZTE
7. Shortcut Delete Rename Properties 3 Select the SSID of your device and then click Connect Wireless Network Connection Mito TAS Choose a wireless network Refresh network list Click an item in the list below to connect to a wireless network in range or to get more information 2 Set up a wireless network USCC MF96U 2200 for a home or small office Q CID AD MN Security enabled wireless network WPA2 To connect to this network click Connect You might need to enter additional Related Tasks pas information JJ Learn about wireless networking Change the order of preferred networks Change advanced settings NOTE Please check the label on your device to get the default SSID 4 Input the password and then click Connect Wireless Network Connection The network LISCC MF960 2200 requires a network key falzo called a WEF key or key or WPA key 4 network key helps prevent unknow m intruders from connecting to this network Type the key and then click Connect Network key Pe A AAA Connect Cancel NOTE You may need to input the password for Wi Fi connection Please check the label on your device to get the default password 5 Your client will connect to the Unite IL Confidential and Proprietary Information of ZTE CORPORATION 7 LTE ZTE Unite II User Manual i Wireless Network Connection Choose a wireless network Network Tasks m Refresh network l
8. System Src Port Dest IP Address Dest Port Protocol Comment 24 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual ZTE Source Port Set the source port of the computer that provides services Destination IP Address Specify a computer located at LAN to provide services Destination Port Set the destination port of the computer that provides services e Protocol Set which protocol will be applied by services e Comment Type comment for the port mapping settings Click Apply to add a new rule Click Delete to delete the rule which you selected UPnP Universal Plug Play UPnP is a set of networking protocols that allows network devices such as PC printers Internet gateways Wi Fi access points and mobile devices to seamlessly discover each other s presence on the network and establish functional network services for data sharing communications and entertainment Select Settings gt Firewall gt UPnP and the UPnP settings page is shown in the following figure UPnP Settings UPnP Settings O Enable Disable Check Enable and click Apply to enable the function DMZ The DMZ host feature allows one local host be exposed to the Internet for a special purpose service such as Internet gaming Select Settings gt Firewall gt DMZ and the following page will appear DMZ Settings DMZ Settings Enable Disable If you select Enable the DMZ Settings will appear C
9. e e Default Policy Set how to handle the packet if none of the rules match A IP Settings Select IPv4 or IPv6 MAC Address Set the MAC address that will be filtered Source IP Address Set the source IP address that will be filtered Destination IP Address Set the destination IP address that will be filtered Protocol Set which protocol will be used for filtering Action Set how to handle the packet if it matches with the rule Comment Type comment for the filter settings Confidential and Proprietary Information of ZTE CORPORATION 23 ZTE ZTE Unite II User Manual Click Apply to confirm your configuration Click Delete to delete the rule which you selected To add a new rule 1 Select Enable in the Port Filtering area 2 Click Apply 3 Input the detail information in the MAC IP Port Filtering Settings area 4 Click Apply in the MAC IP Port Filtering Settings area Port Mapping You can set up Port Mapping to enable external computers to access www FTP or other services provided by LAN Select Settings gt Firewall gt Port Mapping and the Port Mapping page is shown in the following figure Port Mapping Port Mapping Settings Enable Disable If you select Enable the Port Mapping Settings will appear Port Mapping Settings Src Port 1 65000 Dest IP Address e g 132 168 0 101 Dest Port 1 65000 Protocol TCP UDP ba Comment wy Current Port Mapping Rules in
10. on or off the Receive Messages during power up NOTE By disabling the Text Message feature you will not receive any incoming messages when the device powers up in a 4G LTE network You will still receive Text Messages in 3G networks To receive messages when the device powers on please enable the Text Messages feature WPS Web User Interface Configuration Select the WPS icon and press the OK Key to launch the Wi Fi Protection Setup Accessing the Configuration Page 1 Make sure there is a connection between your device and the client 2 Launch the Internet browser and enter http 192 168 1 1 or http uscc hotspot in the address bar NOTE It is recommended that you use IE 7 0 or later Firefox 15 0 or later Opera 10 0 or later Safari 4 0 or later Google Chrome 10 0 or later 3 The login page appears as follows The following figure is only for your reference F US Cellular Password Login On the Web User Interface Configuration page input the password please select Device Info on the LCD screen to get the default password Click Login to log in the device The Web User Interface 1s divided into three parts e Index Shows the configuration list for your device o Content Shows the detailed configuration 10 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual LTE System Information Shows the system status and different kinds of tips HI Shows the batte
11. the LCD screen will be turned on NOTE Only the Wi Fi function will be disabled when the device is connected via USB and no user is connected Press the Power button to enable the Wi Fi function Charging Your Device You can charge your device by using the USB cable or adapter o Use the USB cable to connect your device and PC directly NOTE Do not use excessive force to insert the plug Internet Access You can connect up to 10 Wi Fi enabled devices at one time including computers tablets smartphones and more 4 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual LTE Configuring Your PC Follow the steps for Windows XP to configure the Wireless Internet Protocol for your connection NOTE Wireless Network Connection is used for Wi Fi connection 1 Right click My Network Places and then select Properties Open Explore Search For Computers Map Network Drive Disconnect Network Drive Create Shortcut Delete Rename Properties 2 Right click the Wireless Network Connection and then select Properties SE Wireless Network Connection Disable LL Yiew Available Wireless Networks Repair Bridge Connections Create Shortcut Rename Properties 3 Select Internet Protocol TCP IP and then click Properties Confidential and Proprietary Information of ZTE CORPORATION 5 ZTE L Wireless Network Connection Properties PI
12. the parameters shown in the figure are correct and then click Apply Network Settings Dial up Settings Select Settings gt Network Settings gt Dial up Settings The Dial up Settings page is shown in the following figure You can set the WAN connection mode here The default mode is Automatic Dial up Settings WAN Connection Mode Automatic Check here you can connect to internet in the roaming status O Manual Apply Network Selection Select Settings gt Network Settings gt Network Selection The Network Selection page is shown in the following figure 14 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual LTE Network Selection Network Selection LTE COMA Mas LTE CDMA Apply e LTE CDMA Device connects to LTE CDMA network 3G Auto Device connects to 3G network Click Apply to confirm your configuration NOTE To change the current settings please disconnect from the network first APN Setting Select Settings gt Network Settings gt APN Setting The APN parameters are shown in the following figure Current APN usccintemet Mode Auto Manual Profile usccintemet w PDP Type Profile Name IPv4 APN IPv4 DNS Mode Auto Manual IPv4 Authentication IPv4 User Name IPvd Password IPvb APN usccintemet IPva DNS Mode Auto Manual IPv6 Authentication NONE IPv6 User Name IPv6 Password Sel as default e Click S
13. CORPORATION 29 LTE ZTE Unite II User Manual Device Messaging 0 100 Number Content Time All the received messages saved in your device will be displayed here Click Delete to delete the selected messages Click Refresh to refresh manually Operating Messages in SIM Card You can check the messages saved in your SIM card SIM Messaging Select Messages gt SIM Messaging to access the following figure SIM Messaging All the received messages saved in the SIM card will be displayed here Click Delete to delete the selected messages Check the checkbox next to Delete to select all the messages in SIM card and then click Delete to delete them Configuring Messages Select Messages gt Messaging Settings to access the following figure Messaging Settings Receive SMS during device power up Enable Disable By disabling this SMS feature you will not receive any incoming messages when the device powers up in a 4G LTE network but you will still receive SMS in 3G networks To receive messages when the device powers on please enable this feature 30 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual LTE Warning and Notice To the Owner Some electronic devices are susceptible to electromagnetic interference sent by your device if inadequately shielded such as the electronic system of vehicles Please consult the manufacturer of your device before using 1f necessary
14. SID whether it is valid or empty WPA2 AES PSK It is the securer version of WPA with implementation of the 802 111 standard WPA PSK WPA2 PSK Apply both the WPA PSK and WPA2 PSK scheme Wi Fi Password Enter the password manually LTE Max Station Number Choose the maximum number of the stations which connect to the 4G LTE network simultaneously CDMA Max Station Number Choose the maximum number of the stations which connect to the CDMA network simultaneously Click Apply to confirm your configuration Advanced Settings Select Settings gt Wi Fi Settings gt Advanced Settings the parameters are shown in the following figure Advanced Settings Band Selection Network Mode Channel Bandwidth 20MHz e Country Region Code UNITED STATES v Frequency Channel Auto e Band Selection Select a band from the drop down list Network Mode If all of the wireless devices connect with this device in the same transmission mode the performance will be improved when you choose the appropriate wireless mode Channel Bandwidth Select a channel bandwidth from the drop down list Country Region Code Select the right country code When using the device internationally please change the country region code 18 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual LTE Frequency Channel Select the appropriate channel to optimize the performance and coverage of
15. User Manual LTE US Cellular Customer Service 1 888 944 9400 LEGAL INFORMATION Copyright 2014 ZTE CORPORATION All rights reserved No part of this publication may be excerpted reproduced translated or utilized in any form or by any means electronic or mechanical including photocopying and microfilm without the prior written permission of ZTE Corporation The manual is published by ZTE Corporation We reserve the right to make modifications on print errors or update specifications without prior notice 4G LTE is not available in all areas See uscellular com 4G for complete coverage details 4G LTE service provided through King Street Wireless a partner of U S Cellular LTE is a trademark of ETSI Version No 1 0 Edition Time 1 2014 NOTE Do not use the device in an enclosed environment or where heat dissipation is poor Prolonged work in such space may cause excessive heat and raise ambient temperature which may lead to automatic shutdown of the device for your safety In the case of such event cool the device in a well ventilated place before turning on for normal use Contents SIR o AA A E cadens l Introducti omesse aa l Outincand action l A O OO l Insertune the SIM Card and Batteries 2 Inserting the microSDHC Card eseese e E e a a eE 3 Powerin Om OY oUr DEVIC Gen ias 3 SE dE eaa E E neem ere ne cee er rr 4 Gharemo You DEVi Gena dai 4 MAMA a a 4 COMMS UNS OU PE iia io ita 5 Connecune 10 Yo
16. and check the clients n connected to your device Set the WPS function j Set your device Inserting the SIM Card and Battery 1 Remove the back cover 2 Insert the SIM card into the SIM card slot mu ps a a a e i s2 3 Insert the battery as shown with the contacts located against the metal springs and press the battery down into the case 2 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual LTE 4 Close the back cover Inserting the microSDHC Card NOTE micro P e MicroSDHC logo 1s a trademark of SD 3C LLC o MicroSDHC card is sold separately 1 Pull the microSDHC card cover out of the card slot NOTE Do not remove with excessive force 2 Insert the microSDHC card into the microSDHC card slot as shown below You will hear a click when the microSDHC card locks in place aoe a 3 Close the microSDHC card cover Powering On Off Your Device Press and hold the Power button to switch on off the device Confidential and Proprietary Information of ZTE CORPORATION 3 LTE ZTE Unite II User Manual NOTE The device 1s powered on when the LCD screen lights up Sleep Mode When using battery supply and no users are connected the device will enter sleep mode after a specified time In the sleep mode the Wi Fi function will be disabled Press the Power button to wake up the device and enable the Wi Fi function and
17. ange Extends coverage of mobile hotspot which will decrease battery life o Wi Fi Sleep Settings WI FI Sleep Settings Sleep Time 30 Minutes ho Sleep Time Select a time from the drop down list When there s no Wi Fi connection in the specified time Wi Fi will be unavailable and the system will turn to sleep mode for power saving Confidential and Proprietary Information of ZTE CORPORATION 21 LTE ZTE Unite II User Manual Firewall You may set up firewall rules to protect your network from virus worm and malicious activity on the Internet NOTE You can set the maximum 10 filtering items for MAC IP Port Filtering and Port Forwarding Port Filtering Select Settings gt Firewall gt Port Filtering The MAC IP Port Filtering is shown in the following figure Port Filtering MACAP Port Filtering Enable Disable If you select Enable the filter settings will appear as shown below 22 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual LTE Port Filtering MACAP Port Filtering Enable Disable Default Policy Accepted Dropped wy MAC IP Port Filtering Settings IP Settings IP IPv6 MAC Address e g 00 1E 90 FF FF FF source IP Address Dest IP Address Protocol NONE he Action Accept Drop Comment wy Current MAC IP Port filtering rules in system MAC Address IP Type Source IP Address Dest IP Address Protocol Source Por gt
18. cluding but not limited to lost profits interruption of business cost of capital cost of substitute facilities or product or any downtime cost Radio Frequency RF Energy Only for US Market This model device meets the government s requirements for exposure to radio waves This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency RF energy set by the Federal Communications Commission of the U S Government The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate or SAR The SAR limit set by the FCC is 1 6 W kg Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands Although the SAR is determined at the highest certified power level the actual SAR level of the device while operating can be well below the maximum value This is because the device is designed to operate at multiple power levels so as to use only the position required to reach the network In general the closer you are to a wireless base station the lower the power output The highest SAR value for the model device as reported to the FCC when worn on the body as described in this user guide is 1 26 W kg Body worn measurements differ among device models depending upon available enhancements and FCC requirements 32 Confidential and Proprieta
19. d Right key to view the following information Network Name SSID Displays the default SSID e Wi Fi Password Displays the default Wi Fi password e Web portal Login Displays the login URL of the web user interface Admin Password Displays the default login password of the web user interface e Mobile Number Displays your mobile number e MEID H IMEI D Displays the MEID H IMEI D Firmware Version Displays the firmware version Hardware Version Displays the hardware version Connection Info Select the connection info icon w and press the OK Key to check the connection information Connected Device O Select the connected device icon lt connected to your device and press the OK Key to check the information of the devices Settings Select settings icon and press the OK Key to check the settings Use the Left and Right key to scroll to the desired menu Wi Fi Settings Enable or disable Wi Fi function Network Select Select the network type o Software Update Update the software e Sound Alert Turn on or off the sound alert It is on by default so you will hear an alert when there is one or more device connected to your ZTE Unite II Screen Timeout Set time for screen timeout e Dial 228 Active your SIM card manually in 1X network Confidential and Proprietary Information of ZTE CORPORATION 9 ZTE ZTE Unite II User Manual Messages Settings Turn
20. et as default to set current profile as the default profile Confidential and Proprietary Information of ZTE CORPORATION 15 LTE ZTE Unite II User Manual e Click Add New to access the following figure Current APN usccinternet Mode C Auto Manual Profile PDP Type IPv4 Profle Name IPv APN IPv4 ONS Mode Auto Manual IPv4 Authentication NONE v IPv4 User Name IPvl Password Enter the related parameters please see following table and then click Apply to add a new profile Parameter Function Mode If a fixed APN is provided by your service provider select Manual APN Otherwise please select Auto APN and the device will automatically obtain parameters Profile Selection Choose one profile from the list PDP Type Choose a PDP type from the drop down list IPv4 IPv6 IPv4 amp IPv6 Profile Name Type the profile name Type the APN string DNS Mode Set DNS mode Authentication Password Authentication Protocol PAP provides a simple method without encryption for the peer to establish its identity using a 2 way handshake Challenge Handshake Authentication Protocol CHAP is used to periodically verify the identity of the peer using a 3 way handshake 16 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual LTE User Name User name is used to obtain authentication from the ISP when the connection is established Password Password 1s used to obtain authen
21. isposal or YoUr Od APPIN E ia E euch ahuaeen 33 Troubleshooting ZTE Unite II User Manual LTE Getting Started Introduction ZTE Unite Il is a 4G LTE mobile hotspot device using a 4G LTE network The client devices can connect to ZTE Unite II via Wi Fi The device supports data services enabling you to communicate anytime and anywhere Outline and Parts The following figure shows the appearance of the device It is only for your reference The actual device may be different 8 It indicates the signal type signal strength battery Wi Fi etc 8 microSDHC card slot It is where you insert the microSDHC card Indicators When the device is powered on the following icons will appear on the LCD screen with the corresponding indicators listed in the table below Confidential and Proprietary Information of ZTE CORPORATION 1 LTE ZTE Unite II User Manual Network signal strength Roaming network indication ta Network type 1X 3G 4G LTE icons The device is connected to the will appear on the LCD screen according Internet to the connected network ae Lil Connected to the Internet manually dl There are new messages or unread messages Wi Fi Status and number of the connected W The message inbox 1s full users Battery is low Show and check the device information Battery power indication Show and check the data connection information The battery is full Show
22. ist A Set up a wireless network e USCC MFS6U 2200 For a home or small office ry Security enabled wireless network WPA You are currently connected to this network To disconnect From this network Related Tasks click Disconnect Lij Learn about wireless networking Change the order of preferred networks qpe Change advanced settings Disconnect Accessing the Internet 1 Switch on the device 2 Connect the client to your device 3 After the client is connected to your device successfully you can access the Internet Disconnecting from the Internet Log into the Web User Interface Configuration page click the Disconnect button at the Home page NOTE Powering off the device can also terminate the Internet connection Navigating the Device Press and hold the Power button to turn on the ZTE Unite II The screen lights up to indicate the device has turned on and the following icons will appear after initialization 4a ll tiA E LL U S Cellular a E Device Info Resetting Your ZTE Unite II Simply press and hold the Reset button on right side of the device bottom surface for 3 seconds to restore 8 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual LTE your ZTE Unite II to the factory default settings as shown below Device Info Select the device Info icon and press the OK Key to check the WAN information Use the Left an
23. mation Statistics Select Information gt Statistics and then the statistics information is shown in the following figure Statistics Upload Download Speed 0b s Ob s Duration Downloaded Uploaded Total Used Data Current Connection 00 00 01 0B 0B 0B Current Month 03 37 16 11 52KB 52 TMKB 64 23KB Data usage ls approximate only For actual usage please refer to your network operator Click Clear to clear the information NOTE Data usage 1s an estimate Please see uscellular com myaccount for more information Data Limit Settings Select Information gt Data Limit Settings and then the following page 1s shown Data Limit Settings Data Use Limit Enable Disable If you select Enable the Data Limit Settings will appear Confidential and Proprietary Information of ZTE CORPORATION 27 LTE ZTE Unite II User Manual Data Limit Settings Data Use imt Enable Disable Limit by Data Time Monthly 0 MB Remindme 4 o _ Limit by Select a way to limit the data use by data or time Monthly Set data limit for a month You can select unit from the drop down list Remind me Set a percentage to remind you when the data time reaches the specified percentage File Sharing File sharing allows you to share the files in a SD card via USB cable or web browser Sharing microSDHC Card via USB Cable SD Card Status 3D Card already exists and can be used now Mode USB Full Share 1 Select
24. ollow ZTE s installation operation or maintenance instructions or procedures 111 End User s mishandling misuse negligence or improper installation disassembly storage servicing or operation of the Product iv Modifications or repairs not made by ZTE or a ZTE certified individual v Power failures surges fire flood accidents and actions of third parties or other events outside ZTE s reasonable control vi Usage of third party products or usage in conjunction with third party products provided that such defects are due to the combined usage vii Any other cause beyond the range of normal usage intended for the Product End User shall have no right to reject or return the Product or receive a refund for the Product from ZTE under the above mentioned situations This warranty is End User s sole remedy and ZTE s sole liability for defective or nonconforming items and is in lieu of all other warranties expressed implied or statutory including but not limited to the implied warranties of merchantability and fitness for a particular purpose unless otherwise required under the mandatory provisions of the law Limitation of Liability ZTE shall not be liable for any loss of profits or indirect special incidental or consequential damages resulting from or arising out of or in connection with using of this product whether or not ZTE had been advised knew or should have known of the possibility of such damages in
25. onfidential and Proprietary Information of ZTE CORPORATION 25 LTE ZTE Unite II User Manual DMZ Settings DMZ Settings Enable Disable IP Address Enter the IP address of the device you want to communicate with the Internet and then click Apply to save the settings Router Settings Select Settings gt Router Settings and the router information are shown in the following figure Router Settings IP Address 192 168 1 1 Subnet Mask 255 255 255 0 DHCP Server Enable Disable DHCP IP Pool 192 168 1 100 19 168 1 200 DHCP Lease Time 24 hour s IP Address IP address for LAN interface Subnet Mask Subnet mask for the IP address e DHCP Server Enable or disable DHCP Server function e DHCP IP Pool Allocate begin and end IP address for IP pool e DHCP Lease Time Define how long the leased IP address will be expired The new IP address will be relocated after the IP address is expired Click Apply to confirm your configuration Dial 228 This function allows you to active your SIM card manually in a 1X network Select Dial 228 and the following page will appear Click Dial 228 to active your SIM card Dial 228 26 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual LTE Information This function allows you to view system information Device Information Select Information gt Device Information and then you can view the device infor
26. ry Information of ZTE CORPORATION ZTE Unite II User Manual LTE While there may be differences between the SAR levels of various devices and at various positions they all meet the government requirement The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines SAR information on this model device is on file with the FCC and can be found under the Display Grant section of http www fcc gov oet ea fccid after searching on FCC ID SRQ MF96U FCC Compliance Only for U S Market This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Caution Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However
27. ry level 4 stages from none J to high fil Signal strength _ Taatfll Shows the network signal intensity 5 stages from none T to strong Tatil de Connected to the Internet Internet status EX Disconnected from the Internet Wi Fi strength 1 Wi Fi status and number of the connected users The maximum number is 10 Settings Do not modify any settings unless instructed by your service provider Please disconnect the device from the network before changing the settings Quick Settings l Pe 3 In the main interface click Settings gt Quick Settings Read the guide carefully and then click Next Quick Settings 1 Quick Setup gt 2 A r F p gS The wizard will show you how to set up hotspot safely Click Next to continue click Previous amp Next to navigate and click Apply to save settings Set basic parameters in this wizard For advanced parameters set them in other menu Set PPP Profile Configuration in the following figure and then click Next Confidential and Proprietary Information of ZTE CORPORATION 11 ZTE ZTE Unite II User Manual Quick Settings Previous APN Settings Auto Manual Profile Profile Name usccintemet IPvt APN usccinternet IPvb APN usccintemet 4 Set PPP Authentication in the following figure and then click Next Quick Settings YT 2 3 PPP Authentication 5 Previous PPP Authentication IPv4
28. the device screen and press the OK Key to active your device s WPS 4 Please press the next button on the Client WPS UI After a few seconds the client can access the WLAN and the result will be shown in the Client WPS UI Device Settings Account Management Select Settings gt Device Settings gt Account Management and the administrator settings information is shown in the following figure Account Management Current Password New Password Confirm New Password You can change the administrator s password Click Apply to confirm your configuration Reset Select Settings gt Device Settings gt Reset click Reset to set all the settings to their factory default values and then the device will restart automatically 20 Confidential and Proprietary Information of ZTE CORPORATION ZTE Unite II User Manual LTE Reset Factory Settings Reset Factory Settings Restart Select Settings gt Device Settings gt Restart Click Restart to restart the device Restart Device Power Save Select Settings gt Device Settings gt Power Save You can set Wi Fi performance and Wi Fi sleep to save power e Wi Fi Performance Settings WI FI Performance Settings Wi Fi Performance Short Wi Fi Range Best battery life Medium Wi Fi Range Long Wi Fi Range gt Short Wi Fi Range Increases battery life gt Medium Wi Fi Range Intermediates battery life and Wi Fi range gt Long Wi Fi R
29. tication from the ISP when the connection is established Wi Fi Settings Basic Select Settings gt Wi Fi Settings gt Basic Settings the wireless network basic parameters are shown in the following figure Basic Settings Network Name SSID USCC MF96U 2200 Broadcast Network Name SSID Enable Disable AP Isolation Enable Disable security Mode WPA2 AES PSK he Wi Fi Password e Display Password LTE Max Station Number 10 e COMA Max Station Number 5 w Multi SSID Switch Enable or disable this function Two SSIDs can be used at the same time e Network Name SSID Service Set Identifier SSID Enter a string less than 32 characters as the name for your wireless local area network WLAN Broadcast Network Name SSID Disable or Enable Default this function If Enable is selected the device broadcasts the SSID and other devices can search and connect to it When you select Disable other devices cannot see the SSID If you want someone to connect you need to tell them the SSID and let them setup manually Confidential and Proprietary Information of ZTE CORPORATION 17 LTE ZTE Unite II User Manual AP Isolation Enable or disable this function If Enable is selected the wireless devices connected to your device will be unable to communicate with each other e Security Mode The security modes are described below OPEN You can authenticate successfully with a S
30. ur Device aia 6 ACCESSING the Mermet eano aid 8 Disconnectine fromthe Internet a 8 Nayis ano DE DE nn aio 8 Resetting Your ZTE Unite I ccccccccccccccscccscssscssessscssscsscssscsssssscssscsscsssessscsssssesssees 8 PDOA TM ON aca oo nee ee 9 COMME COO MILO iris nod 9 Bro OF aero ted DEVICE tn dis 9 SO dt et ET 9 WES AAA A eeeeccaena eee alee heath aem ea ceeceaarnsienees 10 Web User Interface Configuration ccccccconnnocnnnnnnnnnnnnnononnnnnnnnnnnnnnnnnnnnnnnnnonnnnnnnnncnnnnnnnnnnnos 10 ACCESSING Me C OI SU TAM ON Las cds 10 Dac E A Seat yan see E cache pene 10 O 11 QUES SC MINDS osetia ener O O Se 11 INGUW OF KS UNO idol 14 WEP S IE 612i ON 17 Device SUING Seui spares A 20 FI a AU ta ii las 22 PROUT S ME ae E E S 26 DN a a a teeta a A a 26 A ONA O 0 terete a Eh E E T en ee ZT Device torno tada 21 EIS A o RO 27 Data arin Oye Ss eects a hee eae dias 21 Pile sO A a a E O 28 Sharins SD Card via USB Cable unos ened e a 28 Sharins SD Gata Via Web BOWSER od 28 1A RESIS S annette nce Ce cert od od 29 Operatine Messages iii IN At Ve sacks idad 29 Operating Messages ani SIMCO 30 Connorin Messie cers sinapsis 30 Wamins and Note nn 31 LODE OWDI AAA A a a a a aa a a aaa 31 site our Deidara acOs 31 Usmo Date anti iss ta 31 Limited Warrants radica 32 Limitation of Lal A A 32 Radio Frequency RF Energy Only for US Market occccccccccnnnnnnnnnnnnnonnccnnnnnnnnnos 32 FCC Compliance Only tor WS Market naaa 33 D
31. waterproof Please keep it dry and store in a shady and cool place Do not use your device immediately after a sudden temperature change In such case it will produce dew inside and outside your device so don t use 1t until it becomes dry Handle your device carefully Do not drop bend or strike it Otherwise your device will be damaged e No dismantling by non professionals and only qualified technicians can undertake repair work Operating temperature range of0 C 35C and humidity range of 5 95 are recommended Using Battery e Do not short circuit the battery as this can cause excessive heat and fire Do not store battery in hot areas or dispose of it in a fire to avoid explosion Do not disassemble or modify the battery When not using the battery for a long period remove it from your device and store it in a cool dry place Never use any charger or battery damaged or worn out Return the worn out battery to the provider or put it in the appointed recycle place Do not dispose of the battery in the trash Confidential and Proprietary Information of ZTE CORPORATION 31 LTE ZTE Unite II User Manual A WARNING If the battery is broken keep away from it If it taints your skin wash your skin with abundant fresh water and ask doctor for help if necessary Limited Warranty This warranty does not apply to defects or errors in the Product caused by 1 Reasonable abrasion 11 End User s failure to f
32. your wireless network Black List Select Setting gt Wi Fi Settings gt Black List the Black List configuration is shown in the following figure Black List Black List Switch O Enable Disable If you select Enable the black list page will appear Black List Black List Switch Enable Disable No Host Name MAC Address 1 Unknown 18 9EFC 56 3E BF Delete Device Information No Host Name MAC Address 1 Z TE 20130523FXB B8 43 86 6E 94 39 Black All the clients connected to your device are shown in the Device Information area Click Block behind the device you want to block and then it will be added to the black list Click Delete to delete the device from the black list WPS You can enable Wi Fi Protected Setup WPS by PIN PIN Code or PBC push button mode on this page If your client device supports WPS there s no need to enter password manually when WPS is available Select Settings gt Wi Fi Settings gt WPS the WPS configuration is shown in the following figure Confidential and Proprietary Information of ZTE CORPORATION 19 LTE ZTE Unite II User Manual SAD USCC MF96U 2200 WPS PIN PBC SSID Select the wireless network name that you want to connect to PIN Enter the PIN that is generated by wireless access client PBC 1 Select the PBC mode in the client WPS UI 2 Select PBC mode in the WPS page of the device and submit 3 Select the WPS icon on
Download Pdf Manuals
Related Search
Related Contents
Teledyne GFC 7001E User's Manual Les SPL : un nouvel instrument de gestion publique au service des manual de instrucciones pag.4 Instructions bock pag Copyright © All rights reserved.
Failed to retrieve file