Talent LP64LED User Manual - Talent Audio Talent Audio
Contents
1. power receptacle to ensure proper voltage B Fixture does not respond to DMX control 1 DMX LED should be on If not check DMX connectors and cables for proper connection 2 If DMX LED 1s on but not responding to a channel check the DMX address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on the cable connectors and on the fixture 4 Try to use a different DMX controller 5 Interference may occur if DMX cables are run alongside high voltage cables C Fixture responds erratically to DMX control 1 You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal 2 Wrong DMX address in the fixture Set the fixture to the proper address 3 Use of microphone cables for DMX connections can cause errors D The fixture doesn t respond to sound 1 Make sure the fixture is not set to receive a DMX signal 2 Check the fixture s internal microphone by tapping the microphone2. together and operate without a controller In Master Slave mode the first fixture will control the others to give an automatic sound activated synchronized light show This function is good for when you want an instant performance The first or master fixture s DMX input will have nothing connected to it Its output connects to the slave fixtures which will be set in slave mode automatically 7 DMX512 Configuration DMX Channel Values 3 Channel Mode RED dimmer RODO 255 GREEN dimmer GO000 255 BLUE dimmer BOOO 255 DMX Channel Values 5 Channel Mode Value omame Fine em os Rebammer em 02s orena O OS em 9288 fa ore a Gradual frequen flash from dark to 133 191 eee bright 192 195 NONE Gradual frequency flash from bright to DMX Channel Values 7 head Mode crame vae O O mon o ene 0255 oReeName O O O OoOO C om os ieam SS C om fos 765 Stroboscopic from slow to fast rae 025s 255 Sets tne spees nen usnga progam the Sets tne spees wen usnga progam when using a program 0 255 Static color select Static mode 025s 255 Strobe speed ee aia le oon Se etermege For sdditional details about DMX operation please review Section 9 8 Troubleshooting Notes Here are some troubleshooting suggestions A The fixture does not work there is no light output 1 Check the connection of power and main fuse 2 Measure the voltage output on your
3. LP64LED Multi color LED Par64 with 181 LEDs User Manual se OF a SOUND SONEALONE J A ACMA of O Please read the instructions carefully prior to use TABLE OF CONTENTS 1 Safety Instructions 2 Technical Specifications 3 Installation 4 How to Connect the Fixture 5 DMX512 Connections 6 How to Set the Unit 7 DMX512 Configuration 8 Troubleshooting 9 DMX General Information 1 Safety Instructions e Please keep this User Manual for future consultation If you sell the fixture be sure to include this instruction booklet to ensure proper maintenance and use e Unpack and check carefully for transportation damage before using the fixture Before operating ensure that the power supply voltage and frequency match the power of your electrical system e It s important to connect the yellow green conductor to ground to avoid electric shock e Disconnect main power before servicing and maintenance e Use a safety cable when permanently mounting this fixture Always handle the fixture with care e Maximum ambient temperature is 104 F e In the event of a serious operating problem stop using the fixture immediately Please contact the dealer from whom you purchased the fixture the nearest authorized technical repair facility or Talent Sound amp Lighting directly e Do not connect the device to any dimmer pack Do not touch exposed wires during use as there might be a hazard of electrical shock e T
4. Manual mode BLUE dimmer a ba a f 25 Static colour select FAJE UIP UU Puge FLUUP PLY FLSH FLOGPFLS I AE AUTO show COURS SHS Sound sensitivity adjust Gradual change speed adjust Hop change mode Strobe speed adjust Static colour storbe speed adjust Your Talent Sound amp Lighting fixture may be operated as a stand alone device that runs on pre programmed routines or sound activation in master slave mode with other devices or via an external DMX512 controller In DMX mode it is configurable to be controlled by 3 5 or 7 channels Besides stand alone operation there are two main ways to control the fixture A Universal DMX control mode B Master Slave operation A Universal DMX controller This fixture s DMX address can be set remotely by a universal DMX controller First you need to program two scenes into a chase and then link the fixtures to the universal DMX controller When you run the chase the fixtures in the chain will set the series DMX address automatically Each lighting fixture needs to have an address set when in DMX mode to receive the data sent by the controller The address number is between 0 511 usually 0 amp 1 are equal to 1 Please refer to the following diagram to set the address for the first four units LT LL SILL SILL 3 The numbers 1 5 9 and 13 indicate the starting address of each of the fixtures B Master Slave operation The fixture allows you to link as many as 16 fixtures
5. a Resistance 120 ohm 1 4Wibetween pin2 DMA jand ping DMA of the last fixture e If you are using a controller with 5 pin DMX output use a 5 pin to 3 pin adapter cable e Connect fixtures together in a daisy chain by connecting the DMX output of the first fixture to the DMX input of the next fixture This cable cannot be branched or split by a Y cable Inadequate or damaged cables bad solder joints or corroded connectors can easily distort the signal cause errors and shut down the system Never allow contact between the data common shield connection XLR Pin 1 and the fixture s chassis electrical ground The DMX output and input connectors are pass through to maintain the DMX circuit if power to one of the units is disconnected e On the last fixture the DMX output should be terminated with a terminator to reduce signal errors Solder a 120 ohm 1 4 watt resistor between pin 2 DMX and pin 3 DMX on a 3 pin XLR plug and connect it to the DMX output of the last fixture 6 How to Set the Unit 6 1 Control Panel F Menu Up D own Enter To select the program functions Up To go forward in the selected functions To confirm the selected funtions Down f go backword in the selected functions 6 2 Main Functions qp Slave mode CHade SCH SE DMX channel select se AR ia ya DMX512 Address doP ig Normal YES Inversion HAN rO gt S55 Manual mode RED dimmer MENU oniro Manual mode GREEN dimmer
6. ght 35 2 Ibs Always use a Safety cable that can hold 12x the weight of the fixture 4 How to Connect the Fixture 3 Pin and 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors into a 3 pin line a cable adapter must be used The chart below details the correct cable conversion nt D eseon i apin ALR pocket gign 9 ji tor 3 1 GND screen NG al A Pin 2 Signal PA Pr 3 Sig mal R i socket 3ND screen Pn 2 Si nal Pri 4 Pin S Nic 5 DMX512 Connections DMX512 is a widely used protocol for intelligent lighting control with 512 available channels Even if you do not wish to operate your Talent lighting fixture via an outboard DMX controller utilizing the master slave mode will still require unit to unit connection by proper DMX cables Caution Common microphone cables may be used to connect small numbers of DMX fixtures over short distances but offer the risk of erratic operation Use of correct DMX cables greatly reduces data errors caused by improper connection DMX INPUT DMX OUTPUT COMMON ee am prs AN f as DMX Hre DMXINPUT 3 a DMX OUTPUT Ww DMX Nees Termination reduces signal errors and to avoid signal transmission problems and interference Itis always _ 3e advisable to connect a DMX terminal
7. o prevent or reduce the risk of electrical shock or fire do not expose the fixture to rain or moisture e The fixture must be replaced 1f there is visible damage to the housing e Do not look directly at the LED light beam while the fixture is on Warning Please read the instructions carefully They include important information about installation operation and maintenance Do not connect more than 32 units in series daisy chaining on a single power circuit Caution There are no user serviceable parts inside the fixture Do not open the housing or attempt any repairs yourself In the unlikely situation your unit may require service please contact your dealer or Talent Sound amp Lighting 2 Technical Specifications e DMX channels 3 5 7 selectable via digital display 181 Ultra Bright 10 mm LEDs Red 49 Green 72 Blue 60 e 125 Static Colors Dimmer Strobe Fade Jump e Auto sound active DMX and master slave modes e Internal programs with sound activation e 3 pin XLR in out sockets for DMX control e RGB color mixing e Beam angle 20 e Power consumption 20 watts e Dimension 9 25 diameter x 11 81 long e Weight 3 52 Ibs 3 Installation The unit should be mounted via its screw holes on its bracket Always ensure that the unit 1s installed to avoid vibration while operating Always ensure that the structure to which you are attaching the unit 1s secure and is able to support a weight of 10x this fixture s wei
Download Pdf Manuals
Related Search