Long-Throw LT-150 Series II
Contents
1. 5 12 21 98 LT 150F Photometrics Chart 90 Flood Distance in Feet Meters E 120 00 140 00 36 57 42 67 21 8 S S888 88 8 VISIBLE LIGHT IR A IR B WAVELENGTH NM Limited Warranty Wildfire Inc warrants to the original owner or retail customer that for a period of three years from the date of delivery of any Wildfire Fixture whether used in a portable or permanent installation such fixtures will be free from defects in material and workmanship under normal use and conditions Warranty does not cover any product or part of a product that has been subjected to accident negligence alteration abuse or misuse and excludes any accessories or parts not supplied by Wildfire Warranty does not cover expendable parts such as fuses lamps glass or any components warranted directly to the owner by the original manufacturer This warranty does not extend to products not manufactured by Wildfire Wildfire s responsibility under this warranty shall be to repair or replace at Wildfire s discretion such parts as determined to be defective upon Wildfire s inspection Wildfire will not assume any responsibility for any labor expended or materials used to repair any equipment without Wildfire s prior written authorization Wildfire Inc shall not be responsible for2. 50 F to 120 F Weight 14 30Lbs 6 48kg Dimensions 7 88 20 01cm High x 7 38 18 75cm Wide x 12 30 48cm Long Accessory Bracket 7 5 19 05cm Standard Equipment Lamp 139 001 Quick Trigger Pipe Clamp 147 020 Safety Cable 147 002 Optional Accessories 7 5 Barn Door 146 001 8 DMX Dowser 147 003 8 DMX Iris 145 001 Floor Stand 147 007 Specifications subject to change without notice Made in the USA Setup amp Operation Unpacking Unpack the fixture and carefully inspect for any signs of physical damage Report any damage to Wildfire or your local distributor immediately Included with each unit should be the following items 1 Pipe mounting clamp designed to attach the fixture to a 11 2 to 2 pipe truss 2 Safety Cable provided to secure the fixture when mounted on a pipe truss 3 Wildfire IronArc Lamp Model LMP 150S Before mounting the fixture you will need to install the lamp Refer to Lamp Replacement on page 6 for correct installation Optional Accessories Floor Stand This aluminum stand set enables you to mount your Long Throw fixture on the floor for footlight applications Contact Wildfire or your local distributor for pricing Installation After installing the lamp place the fixture in desired location The fixture is equipped with a yoke assembly for mounting The yoke may be fitted with either a pipe clamp included for mounting on a pipe truss or a baby bail block or junior pin
3. 13 Thk 18 8 SS 23 1 121 027 Bolt Barrel M COM PH 25 x 1 5 18 8SS 50 1 104 032 05 Yoke LT 250 amp LT 150 24 1 121 026 Screw M COM PH 10 32 25 18 8 SS 51 1 104 026 01 Screen Safety LT 250 25 2 118 002 Draw Latch 52 1 124 003 Lens Clear Boro Float 6 Round 26 2 118 003 Catch Secondary Draw Latch 53 4 104 080 01 Clip Filter Restraining 27 1 139 001 Lamp MH SE UV 150W 54 1 123 003 Lens UV 6 Round Schematic LT 150 Series POWER SWITCH CIRCUIT BREAKER SAFETY SWITCH DEZ BLACK COM WHITE GRND GREEN 150W ELECTRONIC BALLAST 10 Spectral Transmission Graph 100 90 80 70 60 50 40 30 PERCENTAGE OF TRANSMISSION 20 10 o A o o x o o6 o c0 c OO sos UV B UV A Photometrics Chart Beam Diameter Feet Beam Diameter Meters Peak UV A Intensity uW cm Beam Diameter Feet Beam Diameter Meters Peak UV A Intensity uW cm Beam Diameter Feet Beam Diameter Meters Peak UV A Intensity uW cm LT 150S Photometrics Chart 20 Spot Distance in Feet Meters 10 76 11 83 12 89 11 77 LT 150WS Photometrics Chart 50 Wide Spot Distance in Feet Meters 74 60 83 90 93 30 22 74 25 57 28 44
4. fixture Always unplug the unit before cleaning For normal cleaning a dry soft cloth should be used to wipe any surface free from dust and light dirt Cleaning the reflector will require that the lamp be removed Remove the lamp by following the instructions listed under lamp replacement above Once the lamp has been removed gently wipe off the reflector using a soft dry cloth In the event the reflector is heavily soiled lightly dampen the cloth with a mild window cleaning agent and wipe clean The filter lens can be cleaned in the same manner The lamp should be cleaned with alcohol only Troubleshooting The fixture will not strike Check to make sure there is power to the fixture Make sure the power breaker switch on the back of the fixture has not been tripped Unplug the unit Check to see if it has a lamp installed and that it is seated properly in the socket See Lamp Replacement above Check to see if the safety cutoff Switch is making contact by closing the lens cover and listening for a clicking sound If the fixture still is not striking try replacing the lamp If you have checked all of the above and the fixture still won t strike contact Wildfire technical support at 310 755 6780 or your local distributor The effect is not working anymore Try changing the lamp The lamp in your Wildfire fixture is rated at 1000 hours This does not necessarily mean that the lamp will burn out or not light after 1000 hours It may continu
5. have other rights which vary from state to state If any action or preceding results from this warranty the prevailing party will be entitled to all costs and attorney fees incurred in defending or prosecuting such actions White LIGHTING amp VISUAL EFFECTS gnite Your Imagination 2908 Oregon Ct Suite G1 Torrance CA 90503 310 755 6780 800 937 8065 Fax 310 755 6781 www wildfirefx com mail wildfirefx com Wildfire and its symbol are registered trademarks of Wildfire Inc Torrance CA IronArc and its symbol are registered trademarks of Wildfire Inc Torrance CA Ignite Your Imagination is a registered trademark of Wildfire Inc Torrance CA 2011 Wildfire Inc 215 004 03
6. Care should be taken not to touch the new lamp directly Use a cloth or glove when handling If you have touched the lamp it must be cleaned with alcohol to remove any oils and fingerprints prior to striking For maximum UV A output always use Wildfire lronArc lamps and change the lamp in your fixture every 1000 hours Interchanging Reflectors There are three different interchangeable reflectors available for the LT 150 Series a 20 Spot 125 005 02 50 Wide Spot 125 006 02 and 90 Flood 125 007 02 These reflectors are designed to be removed and replaced while the lamp is still in the fixture To remove the reflector unplug the fixture and remove any accessories from the front Make sure the fixture is cool to the touch before opening the front lens assembly cover Unhook the clasps on either side of the fixture allowing the front lens assembly cover to swing down Loosen the four set screws securing the reflector to the brackets on either side of the lamp housing and slide the reflector forward out of the housing Reverse this procedure to install the new reflector The reflector attachment brackets are stamped with S WS and F indicating the proper set position for each reflector Cleaning For best performance the reflector lamp and filter lens should be kept free of dirt and dust At no time should any cleaning chemicals or abrasives be used to clean any part of the fixture Do not spray or apply any liquid directly to any part of the
7. D FIRE DISCONNECT FIXTURE BEFORE RELAMPING USE WITH MAX 250W LAMP TYPE M58 WILDFIRE IRONARC MODEL LMP 250D DRY LOCATIONS ONLY NOT FOR RESIDENTIAL USE WARNING THIS FIXTURE CONTAINS A HIGH INTENSITY UV METAL HALIDE LAMP WHICH IS SAFELY CONTAINED WITHIN AN INTERLOCKING HOUSING WHEN THIS FIXTURE IS USED IN ACCORDANCE WITH THE MANUFACTURERS OPERATING INSTRUCTIONS NO HAZARDS EXIST TO MOST PEOPLE STANDING WITHIN THE BEAM OF THE FIXTURE HOWEVER INDIVIDUALS SUFFERING FROM A RANGE OF SUNLIGHT EXPOSURE DISORDERS APHAKIC AND PSEUDOAPHIKIC OR THOSE INDIVIDUALS RECEIVING PHOTOSENSITIVE MEDICATION MAY RECEIVE DISCOMFORT IF EXPOSED TO ULTRAVIOLET LIGHT HG THE LAMP IN THIS FIXTURE CONTAINS MERCURY MANAGE IN ACCORDANCE WITH DISPOSAL LAWS SEE WWW LAMPRECYCLE ORG OR CALL 1 800 937 8065 Specifications Ballast Electronic Power Factor 9296 Rating 120 277V AC 50 60Hz 2 5 Amps Max 150W Ballast Features Flicker amp Noise Free Automatic Lamp Failure Shutdown Automatic High Temperature Shut Down Automatic Hot Re strike Prevention Circuit Protection 3 Amp Magnetic Over current Breaker Switch Lamp Wildfire lronArc 150 Watt Metal Halide Model LMP 150S 1000 Hr Rated Beam LT 150F 90 LT 150WS 50 LT 150F 20 Reflector Spun Peened Aluminum Alzak Coated Lenses 6 Round Tempered Borosilicate UV A Filter Glass 6 Round Clear Boro Float Glass Peak Spectral Transmission 350 365nm Optimum Operating Temperature
8. Operation Manual High Intensity UV A Lighting Fixture LT 150 Series LONG THROW mite Your Imagination Table of Contents Introduction Safety Statements Specifications Setup amp Operation Unpacking Optional Accessories Installation Operation Maintenance Lamp Replacement Interchanging Reflectors Cleaning Troubleshooting Diagrams Isometric amp Line Views Exploded View Part List Schematic Spectral Transmission Graph Photometrics Chart Limited Warranty 0 CO1010101 C1 Introduction Congratulations on your purchase of a Wildfire Long Throw 150 UV A Lighting Fixture legendary performance in an affordable compact size featuring lightweight energy efficient electronic ballasting for flicker and noise free operation and versatile interchangeable reflectors for a wide variety of configurations Additional safety features include automatic lamp failure shutdown high temperature shutdown and hot re strike protection Please take a moment to read this manual thoroughly before attempting to operate this fixture Improper set up use or servicing may cause damage to the fixture and or lamp and void the unit s warranty Safety Statements CAUTION RISK OF EXPOSURE TO ULTRAVIOLET UV RADIATION DO NOT OPERATE WITHOUT COMPLETE LAMP ENCLOSURE IN PLACE OR IF FILTER GLASS LENS IS DAMAGED DANGER INTENSE HEAT AVOID CONTACT BY PERSONS AND MATERIAL CAUTION RISK OF ELECTRICAL SHOCK AN
9. any incidental general or consequential damages to property damage for loss of use time profits or income or any other charges The owners obligation during the warranty period is to notify Wildfire of any suspected defect to obtain a return authorization number and to return the product freight and insurance prepaid to the following address Wildfire Service 2908 Oregon Court Suite G1 Torrance CA 90503 800 937 8065 310 755 6780 Collect shipments for freight allowances or shipments without return authorization numbers will not be accepted THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ALL OTHER OBLIGATIONS AND LIABILITIES ON WILDFIRE S PART THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF THE OWNER ACKNOWLEDGES THAT NO OTHER REPRESENTATIONS WERE MADE TO HIM WITH RESPECT TO THE QUALITY AND FUNCTION OF THE GOODS SOLD This written warranty is intended as a complete and exclusive statement of the terms thereof Prior dealings or trade usage shall not be relevant to modify explain or vary this warranty Acceptance of or acquiescing in a course of performance under this warranty shall not modify the meaning of their agreement even though either party has knowledge of the performance and a chance to object This limited warranty gives you specific legal rights and you may also
10. e to burn for much longer period of time however the amount of UV it produces will be reduced considerably causing the effect to appear as though it isn t working For maximum effect Wildfire recommends changing the lamp every 1000 hours Isometric amp Line Views lt lt EX XY e 2 4j o Ww y ULE 7 0 12 00 13 87 l 16 87 Exploded View Part List QTY PART PART NAME QTY PART PART NAME 1 1 102 009 01 Housing Ballast LT 150 Series 28 1 108 002 Socket Lamp G12 Base 150W 2 1 102 010 01 Housing Lamp LT 150 Series 29 2 121 061 Washer Tooth 8 18 8 SS 3 1 104 043 03 Control Plate Rear LT 250 30 2 121 069 Screw M PHL PH 8 32 x 3 4 18 8 SS 4 12 121 016 Screw TD SM PHL PH 10 x 1 18 8 SS 31 1 110 011 Ballast MH Electronic 120 277V 50 60Hz 150W 5 1 105 001 Circuit Breaker Carling 3 Amp 32 3 121 059 Wa
11. for mounting on a light stand If the fixture is mounted on a pipe truss be sure to use the included safety cable looping it through the yoke assembly and around the pipe truss This will prevent the fixture from falling and causing possible injury in the event that the pipe clamp was not securely tightened To adjust the angle of the fixture loosen the knobs on either side of the unit slightly rotate to desired angle and tighten Care should be taken to support the front of the fixture while loosening the knobs to prevent the fixture from rotating forward and causing possible injury The fixture comes standard with a 7 5 Bracket assembly for attaching dowsers and scrollers such as Wybron s Eclipse or Coloram Series as well as barndoors and other accessories When using accessories with this fixture be sure to attach the safety cable provided by the accessory manufacturer to the fixtures yoke assembly Plug the fixture into the appropriate power source If you are controlling the unit with a lighting control board you will need to make sure it is plugged into a non dim circuit If the fixture is plugged into a dimmable circuit it will not operate Operation To strike the fixture push the power breaker switch to the on position After striking the lamp allow at least 2 minutes for the lamp to get to full brightness Once the fixture has been powered up and the lamp has ignited if you shut it off you will need to wait approximately 5 minutes
12. sher Flat 8 18 8 SS 6 1 107 001 Cord Power 14 AWG 9 120V 33 4 121 020 Screw M TMB 8 32 x 3 8 18 8 SS 7 1 122 003 Strain Relief Power Cord 34 2 104 006 01 Bracket Reflector Mount 8 1 122 002 Jam Nut Black 1 2 35 1 125 005 02 Reflector LT 150S 9 1 128 015 01 Label Control LT 150 36 1 125 006 02 Reflector LT 150WS 10 1 104 049 01 Divider Plate Lamp LT 150 37 1 125 007 02 Reflector LT 150F 11 4 121 068 Standoff M F 8 32 x 5 16 x 3 8 38 4 121 004 Screw M PHL FH 5 40 x 3 8 12 10 121 037 Kepnut 8 32 18 8 SS 39 1 118 001 Hinge Soss 101 Chrome 13 1 104 048 01 Divider Plate Ballast LT 150 40 2 121 039 Nut SP 8 32 18 8 SS 14 17 121 011 Screw M PHL PH 8 32 x 3 8 18 8 SS 41 1 104 002 01 Bracket Soss Hinge 15 1 104 016 01 Bracket Switch Rod Retaining 42 2 121 013 Screw M PHL PH 8 32 x 1 2 18 8 SS 16 1 104 020 02 Rod Switch LT 250F amp WS 43 1 103 001 09 Lens Door 6 Round LT 250 17 2 104 075 01 Bushing Wire amp Switch Routing 44 1 147 002 Cable Safety 1 8 18 1 105 010 Switch Safety Interlock 45 1 147 020 Clamp Quick Trigger Slimline Black 19 10 121 005 Screw M PHL PH 6 32 x 1 4 18 8 SS 46 2 120 001 Knob Yoke Adjustment LT Series 20 1 104 078 01 Latch Accessory Safety Catch 47 2 103 006 01 Spacer Yoke Assembly 21 1 104 077 02 Base Accessory Safety Catch 48 2 121 032 Rivet Nut Blind 16 x 3 8 22 1 104 098 Spring Double Torsion 49 2 121 060 Washer Flat 1 25 OD 13 32 ID
13. to allow the lamp to cool before the fixture can re strike If the power breaker switch is left in the on position during the cool down period the hot re strike prevention circuitry in the ballast will prevent the lamp from striking until it is completely cooled Once it has cooled sufficiently it will strike automatically This fixture is also equipped with automatic lamp failure protection circuitry that shuts the fixture down if the lamp should fail for any reason preventing any damage to the fixture In addition there is high temperature protection circuitry that shuts the fixture down if the ballast case temperature exceeds 85 C When the fixture cools it will strike again automatically Maintenance amp Troubleshooting Lamp Replacement Unplug the fixture Remove any accessories from the front Make sure the fixture is cool to the touch before opening the front lens assembly cover Unhook the clasps on either side of the fixture allowing the front lens assembly cover to swing down Although the LT 150 Series is designed to allow you to replace the lamp while the reflector is still in place the procedure is easier when the reflector is removed enabling full access to the socket See Interchanging Reflectors below Grasp the lamp in the center and pull forward to remove it from the Socket If the lamp is difficult to remove rocking it gently from side to side will help loosen it from the socket Reverse this procedure to install the new lamp
Download Pdf Manuals
Related Search