User Manual - Austin Hughes
Contents
1. Any damage of the product due to shipment Removal or installation of the product Causes external to the product such as electric power fluctuation or failure Use of supplies or parts not meeting our specifications Normal wear and tear Any other causes which does not relate to a product defect B Removal installation and set up service charges L1 EI EI EI EI EJ EJ Regulatory Notices Federal Communications Commission FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation Any changes or modifications made to this equipment may void the user s authority to operate this equipment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures B Re position or relocate the receiving antenna H Increase the separation between the equipment and receiver B Connect the eq2. into an electrical outlet m When you clean your monitor do not press down on the LCD screen Pressing down on the screen can scratch or damage your display Pressure damage is not covered under warranty B Use only cleansers made specifically for cleaning monitors and monitor screens Cleansers not made to clean monitors and monitor screens can scratch the LCD display or strip off the finish B Do not spray any kind of liquid directly onto the screen or case of your monitor Spraying liquids directly onto the screen or case can cause damage which is not covered under warranty B Do not use paper towels or abrasive pads to clean your monitor Using an abrasive pad or any wood based paper product such as paper towels can scratch your LCD screen Cleaning Your Monitor To clean your LCD safely please follow these steps D Disconnect the power cord Gently wipe the surface using a clean dry microfiber cloth Use as little pressure as possible Cleaning Tough Marks and Smudges To remove tough marks and smudges please follow these steps D Disconnect the power cord Spray a small amount of non abrasive cleanser on a microfiber cloth Caution Do not spray or apply any liquids directly onto the monitor Always apply the solution to your microfiber cloth first not directly on the parts you are cleaning Gently wipe the surface Use as little pressure as possible Wait until your monitor is completely dry before plugging
3. is necessary to keep it from overheating B Arrange the equipment s power cord in such a way that others won t trip or fall over it m f you are using a power cord that didn t ship with the equipment ensure that it is rated for the voltage and current labeled on the equipment s electrical ratings label The voltage rating on the cord should be higher than the one listed on the equipments ratings label B Observe all precautions and warnings attached to the equipment m If you don t intend on using the equipment for a long time disconnect it from the power outlet to prevent being damaged by transient over voltage B Keep all liquids away from the equipment to minimize the risk of accidental spillage Liquid spilled on to the power supply or on other hardware may cause damage fire or electrical shock B Only qualified service personnel should open the chassis Opening it yourself could damage the equipment and invalidate its warranty m f any part of the equipment becomes damaged or stops functioning have it checked by qualified service personnel What the warranty does not cover m Any product on which the serial number has been defaced modified or removed m Damage deterioration or malfunction resulting from O Accident misuse neglect fire water lightning or other acts of nature unauthorized product modification or failure to follow instructions supplied with the product Repair or attempted repair by anyone not authorized by us
4. the below steps to setup the touch screen Step 1 Run the bundled CD disc or download the driver from the link below http www austin hughes com downloads RMDL software html Step 2 Double click the Setup exe Step 3 Follow the installation instruction to finish the setup Step 4 After installation run the TouchKit program amp the 4 point calibration Please do the initial calibration after the first setup Welcome to the InstallShield Wizard for TouchKit The InstallShield Wizard will install TouchKit on your computer To continue click Next UM CV 751 RP F617 Q215V2 P 11 www austin hughes com lt 3 5 gt Options DC Power o e 9c Input rating Input voltage Input range Input current No load Full load Output rating Output voltage Output current Efficiency UM CV 751 RP F617 Q215V2 12 Volt 9 18V 50 mA 4950 mA 12 Volt 4 16A 84 24 Volt 18 36V 50 mA 2450 MA 12 Volt 4 16A 85 P 12 48 Volt 36 75V 50 mA 1220 mA 12 Volt 4 16A 85 RP F617 110 Volt 66 160V 40 mA 993 mA 12 Volt 8 4A 92 www austin hughes com lt 3 6 gt Options MIL type or Lockable Connector Part no MIL Standard MIL type MS3470W8 33P MIL DTL 26482 Connector VGA MS3470W14 15P MIL DTL 26482 Male There are several additional MIL DC and VGA connector types with varying design characteristics to meet co
5. 17 Q215V2 P 6 www austin hughes com lt 2 2 gt On screen Display Operation OSD Ver G56SN20SSTD701 1024 x 768_59 8Hz Image Brightness Contrast Color Temp Red Green Blue Adjust Select 4 Set H OSD Configuration Page for the brightness contrast color temp red green and blue for the auto adjust H position V position phase and clock Video for the colour tint sharpness noise reduction DCDi and TV Setup Audio for volume bass treble balance AVL and mute Misc for the language OSD position graphic mode ratio reset and timer UM CV 751 RP F617 Q215V2 P 7 www austin hughes com lt Part 3 gt lt 3 1 gt Options 3G HD SD SDI input RP F617 Austin Hughes SDI input is an ideal solution for the broadcast grade video and high resolution CCTV market Designed for use with CyberView Full HD 1080p and ultra high resolution 1920 x 1200 LCD displays Austin Hughes provides a SDI input module without using additional space or power and it comes standard with a 2 year warranty DV D AUS power BNC S Video VGA oo O S Video PC For SDI option the AD board will be upgraded to AV3 0 and this comes standard with HDMI DVI D VGA S Video BNC and audio inputs INPUT 3G SDI IN BNC x 1 0 8Vp p 75 ohm 3G SDI OUT BNC x 1 Active through equalized amp relocked Standard Compliance Video S
6. MPTE 425M 274M 296M 125M ITU R BT 656 SMPTE 299M 272M C Compatible Video Format 1080p 60 50Hz 4 2 2 1080p 30 25 24Hz 4 4 4 1080i 60 50Hz 4 4 4 720p 60 50Hz 4 4 4 HD SDI 1080p 30 25 24Hz 4 2 2 1080i 60 50Hz 4 2 2 720p 60 50Hz 4 2 2 SD SDI 480i 60Hz 4 2 2 ITU R BT 656 576i 50Hz 4 2 2 Compatible Audio Format 3G SDI 48kHz 16 20 24 bit 2 CH Synchronized Video HD SDI 48kHz 16 20 24 bit 2 CH Synchronized Video SD SDI 48kHz 16 20 24 bit 2 CH Synchronized Asynchronized Video Max Transmission Distance 3G SDI 150m at 2 97Gb s BEE HD SDI 250m at 1 485Gb s SD SDI 480m at 270Mb s UM CV 751 RP F617 Q215V2 P 8 www austin hughes com lt 3 2 gt Options MCS Multi display Control More control is always good Especially when it is necessary and easy Austin Hughes provides MCS solution to control the OSD of various CyberView LCD display up to 64 units The RS 232C is used for the communication between the PC and the first display via a 15 feet serial cable while the CAN bus is used for the various LCD displays cascade together via CAT 5 6 cable and daisy chain up to 1 000 meters Designed for use with CyberView LCD displays Austin Hughes provides a MCS input module without using additional space or power and it comes standard with a 2 year warranty Audio Power BNC S Video 1 Video PC nu set out in Pl
7. a TM Cybe rView dedicated KVM switch and rackmount screen technology User Manual 17 FHD 1080p LCD RP F617 6U Rackmount Display Panel 1080p Full HD Options SDI MCS AV HDMI Audio Touchscreen DC power MIL type or lockable connector FE CE v REACH 751 Designed and manufactured by Austin Hughes UM CV 751 RP F617 Q215V2 www austin hughes com Legal Information First English printing October 2002 Information in this document has been carefully checked for accuracy however no guarantee is given to the correctness of the contents The information in this document is subject to change without notice We are not liable for any injury or loss that results from the use of this equipment Safety Instructions Please read all of these instructions carefully before you use the device Save this manual for future reference B Unplug equipment before cleaning Don t use liquid or spray detergent use a moist cloth B Keep equipment away from excessive humidity and heat Preferably keep it in an air conditioned environment with temperatures not exceeding 40 Celsius 104 Fahrenheit m When installing place the equipment on a sturdy level surface to prevent it from accidentally falling and causing damage to other equipment or injury to persons nearby B When the equipment is in an open position do not cover block or in any way obstruct the gap between it and the power supply Proper air convection
8. ease download the protocol of MCS control at http www austin hughes com support usermanual cyberview UM CV MCS pdf For MCS option casing depth will be changed Set switch For the 1st and last display RS 232C push the set switch upward For other daisy chain displays 15 feet serial cable push the set switch downward over 15 feet extender required LI e sai SES SS a Cat5 6 cable Cat5 6 cable Cat5 6 cable M max 300 meters max 300 meters max 300 meters RJ 45 jack i Daisy chain up to 1 000 up to 64 displays meters and 64 displays UM CV 751 RP F617 Q215V2 P 9 www austin hughes com lt 3 3 gt AV3 0 Upgrade Options RP F617 HDMI HDMI 1 1 CEA 861 D AV S Video Composite BNC Audio Built in Dual Stereo Speakers 2W x 2 3 5mm audio jacks for audio in amp out DV D ASSI power BNC S Video VGA 000 EJ Video PC UM CV 751 RP F617 Q215V2 P 10 www austin hughes com lt 3 4 gt Options Touchscreen amp driver a F17 USB Touchscreen Specification Model Activation Force lt 50g Stylus R0 8 Compatibility Windows 7 XP Vista Linux B USB touchscreen package includes 1 x 6ft USB cable quick reference guideline and CD disc m For detailed information please refer to the attached CD disc m As the touchscreen unit is not made of toughened glass please handle it carefully USB Touchscreen g DVI D rri Please follow
9. is OFF 50 60Hz Regulatory Safety FCC amp CE certified RoHS2 amp REACH compliant UM CV 751 RP F617 Q215V2 P 4 www austin hughes com Environmental Operating Conditions 20 90 non condensing 5 90 non condensing Physical Product WxDxH 480 x 48 x 266 mm Packing WxDxH 529 x 124 x 451 mm an O Applicable DVI D VGA Input PC Signal ea x 1080 x 60Hz Format E x 768 x 60Hz ee vene x 1024 x 60 75Hz LP x 960 x 60Hz IU 1280x768x60 75Hz EHE EO x 864 x 75Hz Lr 1024x768x60 70 75Hz B48x480x60Hz x 480 x 60Hz EEE 800x600x60 72 75Hz p x 400 x 70Hz ARE __ 640x480x60 72 75Hz SERE x 400 x 70Hz 640x350x70Hz2 ss x 350 x 70Hz UM CV 751 RP F617 Q215V2 P 5 www austin hughes com lt 2 2 gt On screen Display Operation OSD RP F617 Membrane Switch Function Turn the monitor on or off Display the OSD menu Act as an Enter key to select screen setting options Scroll through menu options and adjust the displayed control Exit the OSD screen Go back to the previous on screen sub menu or main menu Remark All LED touch buttons in WHITE light The LED of Power touch button will flash continuously when there is no signal input OO All the LED touch buttons will automatically turn off after 10 minutes of idle status except the Power d Light up all membrane buttons please press any button for 1 2 seconds except the Power O UM CV 751 RP F6
10. it in and powering it up UM CV 751 RP F617 Q215V2 www austin hughes com lt Part 1 gt 1 1 Package Content RP F617 unit X 1 6ft VGA cable X 1 Power adapter X 1 Power cord X 1 1 2 Structure Diagram Front view Rear view OO LCD panel 2 LCD membrane 2 A M lt gt Audio speaker Power cord 4 Power adapter basket DV D AUS Power BNC S Video VGA 909 Video PC Basic I O DVI D VGA AV3 0 upgrade DVI D VGA HDMI BNC S Video audio Options SDI USB for touchscreen amp DC power UM CV 751 RP F617 Q215V2 P 1 www austin hughes com lt 1 2 gt Dimension RP F617 Front View Side View 9 E A v lt gt 190 266 UNIT mm 1mm 0 03937 inch Bottom View CO x 440 Product Dimension Packing Dimension WxDxH W x D x H RP F617 480 x 48 x 266 mm 529 x 124 x 451 mm 4 5 kg 6 kg 18 9 x 1 9 x 10 5 inch 20 8 x 4 9 x 17 8 inch 9 9 Ibs 13 2 Ibs UM CV 751 RP F617 Q215V2 P2 www austin hughes com lt 1 3 gt Installation UM CV 751 RP F617 Q215V2 P 3 Step an B Mount the display panel with M6 screw set m M6 screw x 4 pcs required Left amp right side M6 screw sets are not provided Step B Fix the LCD into the rack www austin hughes com lt Part 2 gt lt 2 1 gt Product Specifications RP F617 When the audio output is connected speaker output
11. st considerations and to provide users with the most design flexibility possible For more information please contact us Part no Standard Lockable YM Ext 461CP001 D type 3W3 Connector s LUSB A111 00 MIL type or Lockable connectors above can be integrated with our LCD displays Sale service just for connectors not provided UM CV 751 RP F617 Q215V2 P 13 www austin hughes com The company reserves the right to modify product specifications without prior notice and assumes no responsibility for any error which may appear in this publication All brand names logo and registered trademarks are properties of their respective owners Copyright 2015 Austin Hughes Electronics Ltd All rights reserved UM CV 751 RP F617 Q215V2 www austin hughes com
12. uipment into an outlet on a circuit different from that to which the receiver is connected UM CV 751 RP F617 Q215V2 www austin hughes com Contents lt Part 1 gt RP F617 1 1 1 2 1 3 lt Part 2 1 2 2 lt Part 3 1 3 2 3 3 3 4 3 5 3 6 2 gt 3 gt Package Content Structure Diagram amp Dimension Installation Specifications OSD Remote Controller Product Specifications On screen Display Operation OSD Options 3G HD SD SDI Broadcast grade input MCS Multi display control solution AV3 0 Upgrade DVI D VGA HDMI BNC S Video Audio F17 Touchscreen Resistive DC Power 12V 24V 48V 110 125V MIL type or lockable connector UM CV 751 RP F617 Q215V2 P 1 P 1 2 P 3 8 P 9 P 10 P 11 P 12 P 13 www austin hughes com Before Installation E itis very important to mount the equipment in a suitable cabinet or on a stable surface B Make sure the place has a good ventilation is out of direct sunlight away from sources of excessive dust dirt heat water moisture and vibration Unpacking The equipment comes with the standard parts shown in package content Check and make sure they are included and in good condition If anything is missing or damaged contact the supplier immediately How To Clean Your LCD Monitor A Caution m To avoid the risk of electric shock make sure your hands are dry before unplugging your monitor from or plugging your monitor
Download Pdf Manuals
Related Search