FX0N-232ADP Installation Manual
Contents
1. Dismounting from DIN rail Slightly pull down the DIN rail mounting clip using a tool such as a slotted screwdriver DIN rail HUE F Xon FX Series 232ADP PLC 4 Product Specification 4 1 Specification All other specifications than the followings are equivalent to those of the FX Series PLC main unit pecification Withstand voltage 500 V AC 1 min between 25 pin D Sub type port and PLC Insulation ee anes 5 MQ or more 500 V DC by Megger between 25 pin D Sub type port and case rower supply Power Supply 5 V DC supplied from PLC main unit max 200 mA specification voltage current Transmission aa Conforming to RS 232C standard Type of isolation Photo coupler isolation Transmission distance 25 pin D Sub type female 15 mor less Performance specification oe a 0 point unrelated to maximum number of controlled points of the PLC occupied I O points FX1S FXon FX1N Half duplex FXon Full duplex Ver 2 00 or later Half duplex Earlier than Ver 2 00 Full duplex Half duplex also possible Following baud rate can be specified when using computer link or no protocol communication 300 600 1200 2400 4800 9600 1 9200 bps Communication Computer link dedicated protocol format 1 format 4 no protocol optional format programming port LED display LED color Power red RD red SD red Communication method Baud rate2. 4 2 Outside Dimensions and Part Names 1 Mounting hole 4 5 04 5 0 18 Used when mounting the 232ADP directly Not used when mounting the DIN rail 2 POWER LED Lit while 5V DC power is supplied from main unit 3 RD LED Lit while receiving data from connected equipment via RS 232C port 4 SD LED Lit while sending data to connected equipment via RS 232C port 5 Cable Used to connect to the main unit 6 RS 232C port 25 pin D Sub female Used to connect with equipment via RS 232C port 7 Screws to fix a cable connector Screw holes M2 6 metric screw thread 8 DIN rail mounting clip 9 DIN rail mounting slot 4 3 Pin Configuration The pin configuration of the RS 232C port on the 232ADP is as shown below 2 04 5 Unit mm inches 90 3 54 80 0 2 3 15 0 01 43 1 69 68 2 68 Weight Approx 0 1 kg 0 22 Ibs Color Munsell 0 08GY 7 64 0 81 DIN rail width 35 mm 1 37 lt lt Pins 4 5 are not used Short circuited inside PIMNO Function S a o 47 Send data 232ADP to RS232C device camer E E 3 Receive data RS232C device to G Send request Data Terminal Ready 232ADP 2 NC Not used Connected internally TH SG Signal Ground Shows RS232C device is ready to 6 lt DR DSR Send enable Data Set Ready receive D OS CS CTS Send enable Signal ground a 8 No connection lt RD RXD Receive data l gt l 45 Si
3. the Symbols Used in this Manual At various times throughout this manual certain symbols will be used to highlight points of information which are intended to ensure the users personal safety and protect the integrity of equipment 1 Indicates that the identified danger WILL cause physical and property damage A 2 Indicates that the identified danger could POSSIBLY cause physical and property damage e Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise as a result of the installation or use of this equipment All examples and diagrams shown in this manual are intended only as an aid to understanding the text not to guarantee operation Mitsubishi Electric will accept no responsibility for the actual use of the product based on these illustrative examples e Please contact a Mitsubishi distributor for more information concerning applications in life critical situations or high reliability Associated Manuals PROGRAMMING MANUAL PROGRAMMING MANUAL II or FX COMMUNICATION USER S MANUAL mentioned below are not provided in sets with a product Contact our agent where the product was purchased to request the manuals accordingly Manual T This FXon 232ADP INSTALLATION JY992D51201 Describes contents related to installation of the manual MANUAL FXon 232ADP Module i Describes contents related to communication FA COMMUNI ATOREUS EMS JY992D69901 available in FX Series PLC suc
4. NKI BLDG MARUNOUTI TOKYO 100 8310 HIMEJI WORKS 840 CHIYODA CHO HIMEuJI JAPAN Side B A JAPANESE B ncus Changes for the Better a MITSUBISHI PROGRAMMABLE CONTROLLERS MELSEGP FXon 232ADP Installation Manual JY992D51201D This manual contains text diagrams and explanations which will guide the reader in the correct installation safe use and operation of the FXon 232ADP hereafter abbreviated to 232ADP and should be read and understood before attempting to install or use the unit Further information can be found in the associated manuals mentioned below Specifications are subject to change without notice Safety guidelines for the user and protection of the FXon 232ADP This manual has been written to be used by trained and competent personnel The definition of such a person or persons is as follows a Any engineer using the product associated with this manual should be of a competent nature trained and qualified to the local and national standards These engineers should be fully aware of all aspects of safety with regards to automated equipment b Any commissioning or service engineer must be of a competent nature trained and qualified to the local and national standards c All operators of the completed equipment should be trained to use this product in a safe and coordinated manner in compliance to established safety practices Note The term completed equipment refers to a third party constructe
5. RS 232C port 2 Communication Functions and Applicable PLC Available in indicated version or later ommunication X1N First First Data transfer via link protocol between PLC and Computer link ue oe product computer specified as the master station No protocol V1 20 First V1 06 First Serial communication without protocol between PLC communication product product and equipment via RS 232C interface Optional First First First Optional port available for suitable programming tool programming port product product product when 232ADP is connected to PLC Remote First First First Program transfer or monitoring enabled via modem maintenance product product product and phone line connected to serial port of PLC 3 Installation Caution A e Use in the environments specified under the general specification in the manual Do not use the product in environments with excessive or conductive dust corrosive or flammable gas oily smoke moisture or rain excessive heat regular impact shocks or excessive vibration as it may result in electrical shock fire malfunction damage or deterioration on the product e Make sure to shut off the power outside the product before installing or wiring it Otherwise electric shock or serious damage to on the product may occur e Never drop wire chips or shavings into the vent slits when drilling screw holes or performing wiring as they may cause fire breakdown or malfunctio
6. Side B A JAPANESE B ncus Changes for the Better a MITSUBISHI PROGRAMMABLE CONTROLLERS MELSEGP FXon 232ADP Installation Manual JY992D51201D This manual contains text diagrams and explanations which will guide the reader in the correct installation safe use and operation of the FXon 232ADP hereafter abbreviated to 232ADP and should be read and understood before attempting to install or use the unit Further information can be found in the associated manuals mentioned below Specifications are subject to change without notice Safety guidelines for the user and protection of the FXon 232ADP This manual has been written to be used by trained and competent personnel The definition of such a person or persons is as follows a Any engineer using the product associated with this manual should be of a competent nature trained and qualified to the local and national standards These engineers should be fully aware of all aspects of safety with regards to automated equipment b Any commissioning or service engineer must be of a competent nature trained and qualified to the local and national standards c All operators of the completed equipment should be trained to use this product in a safe and coordinated manner in compliance to established safety practices Note The term completed equipment refers to a third party constructed device which contains or uses the product associated with this manual Notes on
7. communication JY992D69901 available in FX Series PLC such as wiring MANUAL Ts communication setting and program examples FXis HARDWARE MANUAL JY992D83901 FX0 FXon HARDWARE MANUAL JY992D47501 Describes contents related to hardware of FX PARE aetna J 992D89301 Series PLC such as specifications wiring and FX2n HARDWARE MANUAL JY992D66301 installation FX2nc HARDWARE MANUAL DSS DS JY992D76401 D UL JY992D87201 Describes contents related to instruction in FXo PROGE ANINI MANUAL JY992D76401 EXos FXon FX FX2 FX2c Series PLC Describes contents related to instruction in FX1s PROGRAMMING MANUAL II JY992D88101 FX 1n EXon FEXonc Series PLC FX1n CNV BD JY992D84701 Special Adapter Connection Board Describes contents related to installation of the FX2n CNV BD each board x Special Adapter Connection Board JY992D63601 Manual Name This FXon 232ADP INSTALLATION manual MANUAL Indispensable manual ye Either manual is necessary This manual describes the installation and specifications of the 232ADP For details on wiring with communication equipment system configuration and communication setting and program examples refer to the FX COMMUNICATION USER S MANUAL 1 Outline of Product The 232ADP is an RS 232C communication adapter with a 25 Pin D Sub It is an insulated unit for signal exchange Connected to the main unit of the FX Series PLC it enables serial data transfer between the PLC and equipment via an
8. d device which contains or uses the product associated with this manual Notes on the Symbols Used in this Manual At various times throughout this manual certain symbols will be used to highlight points of information which are intended to ensure the users personal safety and protect the integrity of equipment h 1 Indicates that the identified danger WILL cause physical and property damage A 2 Indicates that the identified danger could POSSIBLY cause physical and property damage e Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise as a result of the installation or use of this equipment All examples and diagrams shown in this manual are intended only as an aid to understanding the text not to guarantee operation Mitsubishi Electric will accept no responsibility for the actual use of the product based on these illustrative examples e Please contact a Mitsubishi distributor for more information concerning applications in life critical situations or high reliability Associated Manuals PROGRAMMING MANUAL PROGRAMMING MANUAL II or FX COMMUNICATION USER S MANUAL mentioned below are not provided in sets with a product Contact our agent where the product was purchased to request the manuals accordingly Hele Description Number P Describes contents related to installation of the JY992D51201 EXon 232ADP Module FX COMMUNICATION USER S Describes contents related to
9. e 5V DC power is supplied from main unit 3 RD LED Lit while receiving data from connected equipment via RS 232C port 4 SD LED Lit while sending data to connected equipment via RS 232C port 5 Cable Used to connect to the main unit 6 RS 232C port 25 pin D Sub female Used to connect with equipment via RS 232C port 7 Screws to fix a cable connector a slike AE erie Screw holes MAO metric screw thread DIN rail width 35 mm 1 37 8 DIN rail mounting clip 9 DIN rail mounting slot 4 3 Pin Configuration The pin configuration of the RS 232C port on the 232ADP is as shown below 2 04 5 Unit mm inches 80 0 2 3 15 0 01 43 1 69 68 2 68 ee Pins 4 5 are not used Short circuited inside PINNo Function S e D 2 Send data 232ADP to RS232C device 83 eT oae Tee 3 Receive data RS232C device to rou Send request Data Terminal Ready 232ADP NC 4 5 Not used Connected Not used Connected internally TH SG Signal Ground LAS Not uses Connected e _ RS232C device is ready to 6 DR DSR Send enable Data Set Ready receive e 5 CS CTS Send enable a Signal ground a e ocom lt RD RXD Receive data l 5 Signal requesting preparation for data a SD TXD Send data sending to RS232C device ay NC Manual number JY997D51201 Manual revision D Date September 2003 a MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE MITSUBISHI DE
10. gnal requesting preparation for data J SD TXD Send data sending to RS232C device ZD NC Manual number JY997D51201 Manual revision D September 2003 Date a MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE MITSUBISHI DENKI BLDG MARUNOUTI TOKYO 100 8310 HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN
11. h as wiring MANUAL Ts communication setting and program examples FXis HARDWARE MANUAL JY992D83901 FX0 FXon HARDWARE MANUAL JY992D47501 Describes contents related to hardware of FX PARE aetna J 992D89301 Series PLC such as specifications wiring and FX2n HARDWARE MANUAL JY992D66301 installation FX2nc HARDWARE MANUAL DSS DS JY992D76401 D UL JY992D87201 Describes contents related to instruction in FXo PROGE ANINI MANUAL JY992D76401 EXos FXon FX FX2 FX2c Series PLC Describes contents related to instruction in FX1s PROGRAMMING MANUAL II JY992D88101 FX in EXon EXonc Series PLC FX1n CNV BD JY992D84701 Special Adapter Connection Board Describes contents related to installation of the FX2n CNV BD each board x Special Adapter Connection Board JY992D63601 Indispensable manual yr Either manual is necessary This manual describes the installation and specifications of the 232ADP For details on wiring with communication equipment system configuration and communication setting and program examples refer to the FX COMMUNICATION USER S MANUAL 1 Outline of Product The 232ADP is an RS 232C communication adapter with a 25 Pin D Sub It is an insulated unit for signal exchange Connected to the main unit of the FX Series PLC it enables serial data transfer between the PLC and equipment via an RS 232C port 2 Communication Functions and Applicable PLC Available in indicated version or later ommunication X e
12. n e Securely install the 232ADP to the designated port Poor connection may cause malfunction 3 1 How to Install to FX Series PLC Installation to FX1S FX1N FX2n Turn OFF the PLC before beginning any work Installation to FX1S FX1N FX2N FX2N in the diagram 1 Remove the panel cover from the top face of the main unit 2 Take off the resin cover from the left side of the main unit 3 Install the following board to the port on the main unit Corresponding model FX1N CNV BD_ FX1N FX1S 4 Fix the above board using the M3 screws supplied Tightening torque 0 3 to 0 6 N m 5 Connect the in built cable of the 232ADP to the port on the FXon FX2NC board from the left side FXanc in the diagram Installation to Installation to FXon FX2nc Turn OFF the PLC before beginning any work 1 Remove the cover of the port for a special adapter provided on the left side of the main unit 2 Connect the in built cable of the 232ADP to the port for a special adapter 3 2 How to Install to Panel Face Direct installation to the panel face FX Series PLC Directly fix to the panel face using 2 sets of a screw M4 a spring washer and a flat washer in the mounting holes Tightening torque 0 7 to 1 0 N m For the pitch and positions of mounting screw holes refer to the external dimensions Screws F Xon 232ADP Mounting on DIN rail Fix the 232ADP to the DIN rail DIN46277 35 mm 1 37 wide
13. nction 3 1 How to Install to FX Series PLC Installation to FX1S FX1N FX2N Turn OFF the PLC before beginning any work Installation to FX1S FX1N FX2N 4 FX2n in the 1 Remove the panel cover from the top face of the main unit diagram 2 Take off the resin cover from the left side of the main unit 3 Install the following board to the port on the main unit Corresponding model FX1N CNV BD FX1N FX1S 4 Fix the above board using the M3 screws supplied Tightening torque 0 3 to 0 6 N m Installation to 5 Connect the in built cable of the 232ADP to the port on the FXoN FX2NC board from the left side FXanc in the diagram Installation to FXon FX2nc Turn OFF the PLC before beginning any work 1 Remove the cover of the port for a special adapter provided on the left side of the main unit 2 Connect the in built cable of the 232ADP to the port for a special adapter 3 2 How to Install to Panel Face Direct installation to the panel face EX Selies PLC Directly fix to the panel face using 2 sets of a screw M4 a spring washer and a flat washer in the mounting holes Tightening torque 0 7 to 1 0 N m For the pitch and positions of mounting screw holes refer to the external dimensions Screws FXon 232ADP Mounting on DIN rail Dismounting from DIN rail Fix the 232ADP to the DIN rail Slightly pull down the DIN rail mounting clip using a DIN46277 35 mm 1 37 wide tool such as a
14. rp Po Bin Pe Poe Computer link V1 20 First V1 06 First Data transfer via link protocol between PLC and product product computer specified as the master station No protocol V1 20 First V1 06 First Serial communication without protocol between PLC communication product product and equipment via RS 232C interface Optional First First First Optional port available for suitable programming tool programming port product product product when 232ADP is connected to PLC Remote First First First Program transfer or monitoring enabled via modem maintenance product product product and phone line connected to serial port of PLC 3 Installation Caution A e Use in the environments specified under the general specification in the manual Do not use the product in environments with excessive or conductive dust corrosive or flammable gas oily smoke moisture or rain excessive heat regular impact shocks or excessive vibration as it may result in electrical shock fire malfunction damage or deterioration on the product e Make sure to shut off the power outside the product before installing or wiring it Otherwise electric shock or serious damage to on the product may occur e Never drop wire chips or shavings into the vent slits when drilling screw holes or performing wiring as they may cause fire breakdown or malfunction e Securely install the 232ADP to the designated port Poor connection may cause malfu
15. slotted screwdriver DIN rail F Xon FX Series 232ADP PLC 4 Product Specification 4 1 Specification All other specifications than the seb eet are equivalent to those of the FX Series PLC main unit pecification Withstand WR 500 V AC 1 min between 25 pin D Sub type port and PLC Insulation aE 5 MQ or more 500 V DC by Megger between 25 pin D Sub type port and case rower supply POwWET Supply 5 V DC supplied from PLC main unit max 200 mA specification voltage current Jranemission Conforming to RS 232C standard Type of isolation Photo coupler isolation Transmission distance 25 pin D Sub type female a of 0 point unrelated to maximum number of controlled points of the PLC occupied O points FX1s FXon FX1N Half duplex Communication FXon Full duplex method Ver 2 00 or later Half duplex Earlier than Ver 2 00 Full duplex Half duplex also possible Following baud rate can be specified when using computer link or no protocol communication 300 600 1200 2400 4800 9600 1 9200 bps Communication Computer link dedicated protocol format 1 format 4 no protocol optional format programming port LED display LED color Power red RD red SD red 15 mor less Baud rate 4 2 Outside Dimensions and Part Names 1 Mounting hole 4 5 04 5 0 18 Used when mounting the 232ADP directly Not used when mounting the DIN rail 2 POWER LED Lit whil
Download Pdf Manuals
Related Search