Maxi-Strob - BoomToneDJ
Contents
1. mono jack signal cable to the INPUT socket on the second slave unit To link further units together in a daisy chain fashion repeat the above step and so on Note For the best results only use the easy remote controller Always abide by the controller user manual specifications regarding the maximum number of strobes that can be linked to one controller Easy controller want to order Daisy chain linking External Controller Strobe 1 INPUT OUTPUT INF Strobe 5 INPUT OUTPUT ZBoomToneDd COM www boomtonedj com2. and is able to support a weight of 10 times of the unit s weight Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture e The equipment must be fixed by professionals And it must be fixed at a place where is out of the touch of people and has no one pass by or under it 2 Technical Specifications Power supply AC 230V 50Hz Power consumption 75W Light source 75W xenon lamp Weight 1 35 kg 3 How to set the unit Manual control mode To control the strobe in manual control mode simply plug the unit into an appropriate mains power supply Then use the flash speed control knob on the rear of the unit to set the desired flash speed The unit will now strobe to the set flash speed Remote control mode To control the strobe in remote control mode first plug external remote controller into an appropriate mains power supply Then plug one end of the 1 4 mono jack cable signal into the INPUT Jack socket on the rear of the unit Now plug the opposite end of the 1 4 6 35mm mono jack cable signal into the OUTPUT socket on the remote controller Please be sure to set all of the manual control knobs to the off position and refer to the strobe controller user manual for operation If you wish to connect a second strobe first plug the 1 4 6 35mm mono jack signal cable into the OUTPUT socket on the first master unit Now plug the opposite end of the 1 4
3. the instructions carefully which include important WARNING information about the installation operation and maintenance e Please keep this User Manual for future consultation If you sell the fixture to another user be sure that he also receives this instruction booklet e Unpack and check carefully there is no transportation damage before using the fixture e It s important to ground the yellow green conductor to earth in order to avoid electric shock e Disconnect main power before servicing and maintenance e Maximum ambient temperature is Ta 40 C Don t operate it where the temperature is higher than this e In the event of serious operating problem stop using the fixture immediately Never try to repair the fixture by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center There are no user serviceable parts inside the fixture e Do not connect the device to any dimmer pack e To preventor reduce the risk of electrical shock or fire do not expose the fixture to rain or moisture e Do not look directly at the LED light beam while the fixture is on Do not touch any wire during operation e The unit should be mounted via its screw holes on the bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure
4. ZZ BoomToneDJ com Maxi Strob 75W Xenon Strobe CE R MODE D EMPLOI USER MANUAL Frangais 1 Instructions de s curit Avant d utiliser votre mat riel nous vous recommandons de lire WARNING l ensemble des instructions de ce manuel Conservez ce manuel pour une future consultation Si vous revendez cet appareil veillez transmettre galement ce manuel d utilisation au nouvel acqu reur D ballez enti rement l appareil ainsi que tous ses accessoires V rifiez qu il n y a aucun dommage et que l appareil se trouve en parfait tat Il est important d utiliser le c ble d alimentation secteur fourni c ble avec terre e Toujours d brancher l appareil avant une intervention technique ou avant son entretien e Temp rature ambiante maximum pour un fonctionnement optimal de l appareil 40 C Ne pas utiliser l appareil si la temp rature ambiante d passe cette valeur En cas de probl me de fonctionnement arr tez imm diatement l appareil Ne pas essayer de le r parer soi m me Contactez votre revendeur ou faites appel un r parateur sp cialis et agr Il n y a aucune pi ce rempla able par l utilisateur Ne pas brancher cet appareil sur un bloc de puissance variable type Dimmer pack Afin de r duire et d viter tout risque d lectrocution ou d incendie ne pas utiliser cet appareil dans un milieu humide ou sous la pluie Ne pas regarder directe
5. ment le faisceau lumineux Cet appareil Maxi Strob doit tre install avec un crochet solide et de dimension ad quate au poids support Lappareil doit tre viss au crochet et serr convenablement afin d viter toute chute due aux vibrations produites par la machine en fonctionnement L accroche de l appareil doit tre s curis e par une lingue de s curit Assurez vous galement que la structure ou point d accroche peut supporter au moins 10X le poids de l appareil accroch L appareil doit tre install par une personne qualifi e et doit tre plac hors de port e du public 2 Caract ristiques techniques Tension d alimentation AC 230V 50Hz Consommation Electrique 75W Source Lumineuse lampe 75W au Xenon Poids 1 35 kg 3 Modes de fonctionnement Mode Manuel Branchez l appareil au secteur utilisez le bouton rotatif pour ajuster la vitesse des flashs Mode contr l par un contr leur de Strobe externe Connectez votre contr leur sur l entr e INPUT de votre Maxi Strobe en utilisant un c ble Jack 6 35mm La vitesse des flashs sera alors contr l e par votre contr leur externe et non plus par le bouton rotatif de l appareil Vous pouvez brancher les Maxi Strobe en cascade et ainsi contr ler tous les Flashs simultan ment Contr leur Externe Strobe 1 INPUT OUTPUT INR Strobe 4 Strobe 5 PUT OUTPUT INPUT OUTPUT 1 Safety Instructions A Please read
Download Pdf Manuals
Related Search