P-0921 Instruction Manual - Channel Vision Technology
Contents
1. DOOR 1 DOOR2 CHIME 2 CHIME 1 o o UNLOCK UNLOCK DOOR 1 o AUX TELCO INPUT CO NoCO a ao 8 9 E 8 F 2 DOOR TELEPHONE ENTRY CONTROLLER P 0921 2 DOOR TELEPHONE ENTRY CONTROLLER CHANNEL VISION 2007 CHANNEL VISION TECHNOLOGY The P 0921 provides communication between two different Channel Vision door intercoms and any phone in the house When a visitor presses the doorbell button the phones in the house will respond with a distinctive ring The home owner can then speak to the visitor by answering any of the ringing phones in the house Features e Supports 2 Channel Vision door intercom stations Rings the phones when the doorbell button is pressed e Integrated door chime contacts for triggering a traditional doorbell e Programmable auxiliary dry contact closure e Page output for whole house paging system e Can work with or without an active telephone line e LED status indicators e Quick and easy installation Telephone service input output Use either the RJ 45 or screw terminals CHIME 1 and 2 are dry contacts which close whenever the corresponding doorbell button is pressed Unlock Door 1 and 2 allows a door strike relay to be triggered when these terminals are shorted by the press of a button AUX contact closure can be configured to close when STRIKE 1 is active2. o5 n nN a 9g EI g 35 Sk EE E 3 Es amp 23 ELCO 2 DOOR TELEPHONE ENTRY CONTROLLER To Strike ww O0 Mechanism UTPUT V idi E ooo ooo To Whole House Paging System 4 House Channel Vision Compatible Telephones Door Intercom Station User Codes User codes for P 0921 Replace x with or depending on the position of the switch Key codes Function xxx1 Talk with DOOR 1 XXX2 Talk with DOOR 2 XX When on a phone call places call on hold amp answers door press again to go back When not on a phone call answers the last door station activated x5 Activate page out function the following codes work while you talk to the door x71 Activate STRIKE 1 can use AUX terminals or TE110DS module x72 Activate STRIKE 2 Requires TE110DS module Examples assuming the P 0921 is set for operation The user dials they will be connected to the last door station that was activated Pressing again will toggle to the other door The user dials 1 they will be connected to DOOR 1 Then while talking The user dials 71 strike 1 will be activated The user dials 2 they will be connected to DOOR 2 Then while talking The user dials 72 strike 2 will be activated Call Waiting functions Situation Doorbell is pressed when you are already on the phone You will hear You will
3. OR when PAGE is active Enables operation when no active CO line is present Selects the activation key either or 2 DOOR TELEPH ON ENTRY CONTROLLER Audio page output for whole house paging systems Door 1 and 2 are connections for Channel Vision Door stations Use either RJ 45 or screw terminal connections Other Telephone Entry Components Door Intercom Units Your telephone entry system will require at least one of the following compatible door intercom stations These door intercoms are constructed of 1 4 solid brass and are offered in 9 different finishes to match the most popular door hardware They can be ordered with or without a hidden camera for covert surveillance Both color and black amp white camera options are available e DP Intercom isa wide that was designed to look large unit measuring good in large scale IU Intercom is a single gang unit measuring 4 1 2 tall by 2 3 4 wide perfect for locations where the larger DP intercom unit 6 1 2 tall by 4 3 8 O entry ways is not desirable Part numbering DP and IU Intercom Options XX 0212 L Blank Channel Vision compatible C 0920 P 0920 P 0921 P Panasonic compatible 212 White 222 Polished Brass 232 Antique Brass 242 Chrome 252 Oil Rubbed Bronze 262 Antique Copper 272 Satin Silver 282 Black 302 Satin Nickel 0 No camera 5 Black and white camera 6 Colo
4. hear call waiting beeps press or to be connected Situation You have placed the caller on hold and switched to the door intercom You will hear Occasional beeps reminding you that a call is holding Situation You are speaking to the door intercom when an incoming phone call is detected by the system You will hear Beep beep pause Beep beep pause etc Situation The doorbell is pressed at the same time as an incoming call is detected When you pick up the receiver you will be connected to the incoming call You will hear Beeps corresponding to the distinctive ring for the door intercom being activated Programming Codes To program the advanced options of the P 0921 pick up any telephone in the system and enter the touch tone codes listed in the chart below Default Settings CHIME 1 and 2 are momentary closure STRIKE 1 and 2 is set for a 3 second closure period AUX is configured to provide contact closure when STRIKE 1 is active Distinctive Ring is set for option 3 CHART 1 Programming procedures for P 0921 X 0 Z FIRST Call the door station from a telephone press or Replace x y and z with numbers shown below When finished press or and listen for confirmation beep See example below Momentary closure for strikes and chimes contacts 300 msec 9 For CHIME 1 amp CHIME 2 See CHART 1 A 9 ForSTRIKE 1 amp STRIKE 2 See CHART 1 B 5 For distinctive ring selection See CHART 1
5. C 2 Press 1 for contact closure when STRIKE 1 is active Press 2 for contact closure when Page is active To program CHIME 1 To program CHIME 2 To program Distinctive Ring To program AUX contact To program STRIKE 1 To program STRIKE 2 Oo oco N c Press 0 to enter the programming mode press or to save changes Hang up the phone to exit without saving If the P 0921 is set for operation determined by switch If the P 0921 is set for operation determined by switch CHART 1 A CHART 1 B CHART 1 C CHIME duration STRIKE duration Selecting a distinctive ring Option Duration of Option Duration of operation_ operation contact closure contact closure Door 1 Door 2 Door 1 Door 2 1 3 seconds 1 3 seconds 1 2 1 2 2 2 3 2 5 seconds 2 5 seconds 2 2 3 2 4 21 3 8 seconds 3 8 seconds 3 3 5 2 3 4 16 seconds 4 16 seconds 4 2 3 2 5 3 5 25 seconds 5 25 seconds 5 3 5 3 6 60 seconds 6 60 seconds 1st ring 2nd ring 7 120 seconds 7 120 seconds examples 8 180 seconds 8 180 seconds 2 1 ring ring ring 9 240 seconds 9 240 seconds 2 3 ring ring ring ring ring Example assuming the P 0921 is set for operation First access the intercom system by pressing To set STRIKE 2 to operate for 8 seconds pick up any touch tone phone in the system and dial 073 listen fo
6. Door Stripping and Connecting CAT5 Wire CAT5 cable should be stripped with a proper stripping tool such as Channel Vision s J 110 tool 1 Place the CAT5 between the blade and the first notch of the J 110 tool 2 Rotate the tool only once Multiple turns will cause you to cut into the inner wires Rotate 1 turn only 3 Inspect the inner wires for damage If any wires are cut start over at step 1 Slight pressure TIA 568A RJ 45 Modular Plug Side view Top view Troubleshooting 1 When the doorbell is pressed the phones do not ring but you can activate and speak to the door station by pressing 1 or 1 depending on setup a Make sure that you have the correct power supply and that it is supplying 12 VAC b Measure the AC voltage on the TELCO Output terminals at the time when the unit should be ringing just after the doorbell button is pressed There should be between 70 90 VAC across the terminals during a ring cycle 2 The phones in the house cannot communicate with the door station a Make sure the power supply is plugged in b Make sure the phones are connected to the TELCO Output on the telephone entry controller To be sure of this connect one phone directly to the TELCO Output screw terminals and test the unit 3 A static or screeching noise is heard when speaking to the door station a If DSL is present in the system inst
7. all a DSL filter model P 0411 on the phone line before the telephone entry controller 4 The TE110DS does not activate a Make sure you re pressing the correct key sequence If already speaking to the door station just press 71 or 71 If not already speaking to the door station press 1 71 or 1271 b Measure the voltage on the screw terminals labeled INTERCOM When the system is idle there should be 1 VDC on the terminals When speaking to the door station there should be about 6 VDC on the terminals When the TE110DS is activated there should be atleast 10 VDC on the terminals Specifications Connectors Screw terminals and RJ 45 TIA 568A REN 0 1 Ring Output gt 5 capable of ringing gt 10 phones with a REN of 0 5 Power Supply 12VAC 500mA Dimensions 6 5 x 7 0 x 1 5 Specifications subject to change without notice 11 CHANNEL VISION 2 Year Limited Warranty Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts free of charge in the USA for two years from the date of original purchase This is a no hassle warranty with no mail in warranty card needed This warranty does not cover damages in shipment failures caused by other products not supplied by Channel Vision Technology or failures due to accident misuse abuse or alteration ofthe equipment This warranty is extended only to the origi
8. ils Green Green White wire From P 0921 Door 1 or Door 2 Cut the outer jacket of the CAT5 wire Separate and cut the green amp green white Connect them as shown Leave all other wires intact TE110DS power To Strike Door Intercom Station supply Mechanism Using the Page Out Function One major benefit of the 2 Door Telephone Entry System is that many different components can be integrated with it The system below integrates the Page Out feature of the P 0921 with the local audio input on the P 1014 1x4 CAT5 Audio Distribution Module When a page is sent from the P 0921 it will interrupt the main audio source feeding the P 1014 so the page will be heard through the audio system s speakers This is a great way to make pages audible in multiple areas throughout the home CO fo pj Bathroom Kitchen AB 124 Amplified Keypad Telephone Service lo SEM iEM iGm He DBe EER ifm ite jae El Model FERED M ico L 2 DOOR TELEPHONE ENTRY CONTROLLER INP SL s cable Sat radio Ceeeeee LL DVD playerf ecce AB 202 E ICD player sssf Input rr 25 Module Cmm ETIN NN House Telephones
9. nal purchaser and a purchase receipt invoice or other proof of original purchase date will be required before warranty repairs are provided Mailin service can be obtained during the warranty period by calling 800 840 0288 toll free A Return Authorization number must be obtained in advance and can be marked on the outside ofthe shipping carton This warranty gives you specific legal rights and you may have other rights which vary from state to state If a problem with this product develops during or after the warranty period please contact Channel Vision Technology your dealer or any factory authorized service center CHANNEL VISION www channelvision com 234 Fischer Avenue Costa Mesa California 92626 USA 714 424 6500 800 840 0288 714 424 6510 fax email techsupport channelvision com SOS DA
10. r camera DP Large size 6 1 2 x 4 3 8 IU Single gang size 4 1 2 x 2 3 4 o ISS SS gt iss TE110DS is a dry contact relay that can be connected in line between the P 0921 and the door intercom station It is activated by the same commands that control STRIKE 1 and STRIKE 2 Basic Setup amp Operation When the button is pressed on the door intercom the phones in the house will ring If a doorbell chime and transformer are connected to the CHIME contact the doorbell chime will also be heard If the phone is answered within 20 seconds it will be automatically connected to the door intercom If the phone is answered after 20 seconds simply press or to be connected Note the activation key is determined by the switch labeled or While speaking to the door intercom the STRIKE 1 contact can be activated by pressing 71 or 71 The Unlock Door terminals can be momentarily shorted with a simple push button which will activate the strike without the use of a telephone To send a whole house page from any phone press 5 or 5 see the following page for a full list of user codes Doorbell Simple push button optional Chime Telephone and Service Transformer g Strike power supply DOOR 1
11. r confirmation tone To set STRIKE 2 to operate for 25 seconds pick up any touch tone phone in the system and dial 085 listen for confirmation tone Four Door Application Two of the P 0921 can be used to serve up to 4 different door intercoms Simply connect and configure the units as shown below Note be sure to set one unit for operation and the other unit for O o Cj SER iE ifm Gm e Set this switch for Telephone I M al operation Service 5EB EB e SEB El ios P921 2 DOOR TELEPHONE ENTRY CONTROLLER Set this switch for HGR DB ie HERO ae operation HER ich im ipee Gl SS REN P 0921 o L House Door 3 Door 4 7 Telephones Using the TE110DS The TE110DS is not always required when using the P 0921 because the P 0921 has a built in AUX relay that can be programmed to control one electronic door strike However it may still be used for applications that require a remote contact closure that is located near the door intercom station If using the RJ 45 connection on the P 0921 simply connect the green and green white wires from the CAT5 to the terminal inputs and outputs of the TE110DS as shown below If using the screw terminal connectors on the P 0921 simply use the same Connection Deta
Download Pdf Manuals
Related Search