LED STUDIO PAR PLATINUM 20X3W PWM RGB
Contents
1. Di Chanel Value Function 0 255 0 Off 1 255 different colourmacros 36 DMX MODE 2 DMX IL 0 255 0 Off 1 255 different colourmacros 36 0 255 O off 1 255 Dimmer 1 100 DMX MODE 3 DMX MODE 3 0 255 RED 0 OFF 1 255 DIMMER 1 100 OUTPUT 0 255 GREEN 0 OFF 1 255 DIMMER 1 100 OUTPUT 0 255 BLUE 0 OFF 1 255 DIMMER 1 100 OUTPUT DMX MODE 4 DMX MODE 4 0 255 RED 0 OFF 1 255 DIMMER 1 100 OUTPUT 0 255 GREEN 0 OFF 1 255 DIMMER 1 100 OUTPUT LERNEN CREE 3 025 BLUE 0 OFF 1 255 DIMMER 1 100 OUTPUT 0 255 STROBE 0 15 OFF 16 255 1Hz 12Hz 2 3 A 0 255 MASTER 0 OFF 1 255 DIMMER 1 100 OUTPUT 8 12 IQnition LED Studio Par Platinum 20x3W PWM DMX MODE 5 Function 0 255 RED 0 OFF 1 255 DIMMER 1 100 OUTPUT MASTER 0 OFF 1 255 DIMMER 1 100 OUTPUT Special functions 0 31 Inactiv 32 63 Automatic Dimming upwards 64 95 Automatic Dimming downwards 96 127 Automatic Dimming upwards downwards 128 159 Automatic colourchase 160 191 coincidence colour chase 3 colours 192 223 coincidence colour chase 7 colours 224 255 start music control DMX MODE 6 Compatibility mode RED 0 OFF 1 255 DIMMER 1 100 OUTPUT 2 0 255 GREEN 0 OFF 1 255 DIMMER 1 100 OUTPUT BLUE 0 OFF 1 255 DIMMER 1 100 OUTPUT 4 0 255 0 Off 1 2552. ignition USER S MANUAL LED STUDIO PAR PLATINUM 20X3W PWM RGB IQnition LED Studio Par Platinum 20x3W PWM Table of contents Sales Eier TUTTI 3 2 A MAMM m e UR A 5 2E ET a m i E 6 3 1 aaa 6 3 2 Kee 6 3 3 Maa Run EE 6 3 4 Manual COIOUNS e TE 6 MOB EE 7 e BNA Eege 7 o A mem 10 Te CIMA NC AAAMOOO o A 11 2 12 IQnition LED Studio Par Platinum 20x3W PWM 1 Safety instructions FOR SAFE AND EFFICIENT OPERATION Be careful with heat and extreme temperatureAvoid exposing it to direct rays of the sun or near a heating appliance Not put it in a temperature bellow 41 F 5 C or exceeding 95 F 35 C Keep away from humidity water and dust Do not place the set in a location with high humidity or lots of dust Containers with water should not be placed on the set Keep away from sources of hum and noise Such as transformer motor tuner TV set and amplifier To avoid placing on un stable location Select a level and stable location to avoid vibration Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust or a wet soft cloth for stubborn dirt If out of work contact sales agency immediately Any troubles arose remove the power plug soon and contact with an engineer for repairing do not open the cabinet by yourself it might result a danger of electric shock Take care with the power cable Ne
3. Item has to be qualified Connect item with the main plug The voltage and frequency must exactly be the same as stated on the device The power plug must always be inserted without force 1 3 Cleaning and Maintenance Please make sure that safety relating and machine technical installations are inspected by a skilled person once a year 1 Make sure before installing that all screws are tightly connected and not corroded 2 here must be no deformations on the housings fixations and installations spots 3 No damages must be showed on the power supply cables material fatigue and sediments If the device is going to be cleaned please use moist lint free cloths Never use alcohol or solvents The cooling fan must be cleaned monthly To clean the interior of the device please use a vacuum cleaner or an air jet We recommend cleaning the lenses weekly to keep the light output as long as possible 2 DMX Mode You are able to work with the fixtures in 3 different modes DMX Mode in this Mode its possible to control via DMX Controller Program Mode in thsi mode you can use the built in programs Speed Mode in this mode you can adjust the program speed Sound Mode in this mode the fixture reacts to sound impulse 5 12 ICI GIOrn LED Studio Par Platinum 20x3W PWM 3 Set Up 3 1 DMX ADD Defines the DMX start address 3 2 Display settings Display Backaround lights on Display background light turn off af
4. different colourmacros 36 0 255 STROBE 0 15 OFF 16 255 PULSE SLOW FAST Special functions 0 31 Inactiv 32 63 Automatic Dimming upwards 0 255 64 95 Automatic Dimming downwards 96 127 Automatic Dimming upwards downwards 128 159 Automatic colourchase 160 191 coincidence colour chase 3 colours 0 255 MASTER 0 OFF 1 255 DIMMER 1 100 OUTPUT 9 12 IQnition LED Studio Par Platinum 20x3W PWM DMX SLAVE The unit is controlled by the master unit 6 Program Mode Speed mode a gt ojojo 000 031 Programspeed 000 STOP 001 031 fast 7 gt slow Sound mode PES SOUND SENS JOJOJO SENS 1031 000 091 Sound sensitivity 000 OFF 001 031 low __ high 10 12 IQnition LED Studio Par Platinum 20x3W PWM 7 Technical Data me mm o o DMX In 3pin XLR male socket DMX Out 3pin XLR female socket DMX Pin assignment Pin 1 ground Pin 2 Pin 3 11 12 IQnition LED Studio Par Platinum 20x3W PWM Importeur B amp K Braun GmbH Industriestra e 1 D 76307 Karlsbad Ittersbach www bkbraun com info bkbraun com PlU c2U002l1 91 12 12
5. nd or damage to property Use only professional trussing systems if the Item shall be lowered from the ceiling or high joists Never let the Device swing freely in a room Caution Overhead Items may cause serious injuries when crashing down If there is concern about the safety then DO NOT INSTALL the Device DANGER OF FIRE When installing the device make sure there is no highly inflammable Material decoration articles etc within a distance of min 0 5 m Mount the projector with the mounting bracket to your trussing system using an appropriate clamp For overhead use always install a safety rope that can hold at least 12 times the weight of the fixture You must only use safety ropes with quick links with screw cap Pull the safety rope through the hole in the mounting bracket and over the trussing system or a safe fixation spot Insert the end in the quick link and tighten the safety screw The maximum drop distance must never exceed 20 cm A safety rope which already held the strain of a crash or which is defective must not be used again Adjust the desired inclination angle via the mounting bracket and tighten the fixation screws DANGER TO LIFE Before taking into operation for the first time the installation has to be approved by an expert 4 12 IQnition LED Studio Par Platinum 20x3W PWM 1 2 Power Connection I CAUTION Never leave this device running unattended Every person that is involved with this
6. ter 10s Display shows the temperature of the board in C When the temperature is above 70 C the output rating will reduce down to 30 until the temperature falls back to 70 C That s to protect the LED and give it a long lifetime 3 3 Manual Dimmer oyoo aoo UC Manuel dimming 0 100 This setting overwrites every other setting like the max output in manuel or DMX mode and the built in programs 3 4 Manual colourselection 000 RED Determines the maximum intensity of the colour red 0 100 This setting overwrites every other setting like the max output in manual or DMX mode and the built in programs 6 12 IQnition LED Studio Par Platinum 20x3W PWM Determines the maximum intensity of the colour green 0 100 This setting overwrites every other setting like the max output in manual or DMX mode and the built in programs Determines the maximum intensity of the colour blue 0 100 This setting overwrites every other setting like the max output in manual or DMX mode and the built in programs 4 Reset Hold If you push and hold for more than 3 sek the SETUPDIM will do a reset 5 DMX Mode DMX Mode Display blink if there is no DMX signal Connect the signal out of you controller with the XLR in plug on the fixture On the XLR out you can connect other DMX controllable fixtures DMX OUT DMX IN 7 12 IQnition LED Studio Par Platinum 20x3W PWM DMX MODE 1
7. ver pull the power cable to remove the plug from the receptacle be sure to hold the plug When not using the player for an extended period of time be sure to disconnect the plug from the receptacle 3 12 IQnition LED Studio Par Platinum 20x3W PWM 1 1 Overhead Rigging This Item must be built in a way that it can hold 10 times more of its weight for 1 hour without causing any damages The installation must be secured with a secondary safety attachment The safety attachment has to be constructed in a way that no part of the installation can fall down When rigging de rigging or servicing the fixture staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden Before taking the device in operation the installation must be approved by an expert The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year Procedure The Device must be installed outside areas where persons may walk by or be seated IMPORTANT OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the projector If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury a
Download Pdf Manuals
Related Search