Kid tracker 401_20140530.ai
Contents
1. Kid Tracker 401 User Manual Base unit T LED light Tag unit FinMe Light a ae Direction indicator Front Back button M _ Onw Key ring hole P Distance indicator O Orar gt Search button N on maS Power on off Power on Power off Battery cover Kid Tracker 401 Search amp Tracking amp Alarm Digital 2 4 GHz RF Frequency range 2 40 2 48MHz 0 300 feet Near 10 5m Short 20 5m Middle 30 15m Far 50 20m Battery Installation Base unit a Remove screw and take off the battery b Insert the 3 batteries into the battery cover compartment Make sure that the positive and negative ends of the batteries follow the markings on the bottom of the battery compartment Tag unit a Take off the battery cover and insert the battery Make sure that the positive and negative ends of the battery follow the markings on the bottom of the battery compartment b Place the battery cover back GETTING STARTED For first time use please insert the batteries into both the Base unit and Tag unit Clip the D Ring into the key ring hole of the Tag unit to attach onto the kid s lanyard or the dog collar Place the Base unit and Tag unit no further than 4 apart Switch both the Base unit and Tag unit on Make sure when both units are on LED lights on both units are flashing at the same rate P2. and 2 this device must accept an interference received including interference that may cause undesired operation FCC Caution Any changes or modifications are not expressly approved by the party responsible for compliance which could void the user s authority to operate this equipment EU Declaration Conformity This product is carrying the CE Mark in accordance with the related European Directives C 91E 02A9 U50G20
3. e in order to preserve battery life in both devices Simply switch the Base unit on when you want to activate the wireless leash again Important If the Base unit is turned on with the Tag unit out of range the LED on the Base unit will be constantly on for one minute or until it s within the range and connected again otherwise it goes into sleep mode LOW BATTERY When one of the unit is low on battery a low battery alert beep will sound every 2 minutes Please insure battery is replaced as this can effects the wireless leash s ability to work properly BUTTON FUNCTION amp LED INDICATION Function Operation LED Indication Sound Indication Power Off pnr Sandoy mode switch Power x x Signal indication LED flashes Power On Switch Power button from OFF to ON RED light every second X Under Standby mode the distance Signal indication LED flashes High beeps continus for two Alarm between the Base unit and Tag unit F minutes if it can t link Base A RED light every second Sapo is 80 110ft unit will beep every minute When Base unit alarms shorten the PENES Stop Alarm distance between the Base unit and the Signal diratan PED nasnes No beep p Tag unit within 100ft RED light every second Distance between Base unit amp Tag unit is closer More LED light up Melody is more rapid Distance between Base unit amp Tag unit is farther Melody is slower and LED light decreasingly diminuendo Under standb
4. lace the Tag unit on around your kid s neck or pet The Base unit can be held anywhere but is recommended that it stays out in the open for best results while using the wireless leash Suggested Setting Place Oouahwond Base unit Tag unit SEARCH TRACKING MODE 1 If your wireless leash Base unit alarm activates or when you wish to search for the approximate location of the Tag unit simply press the Search button as per Base unit diagram 2 When search button is pressed the Base unit will start beeping away Make sure you hold the Base unit upright pointing forward like a remote control and turn in different directions slowly 3 When searching around make sure you do not point and switch directions too fast as the signal take time to send and bounce back for a position As per diagram the distance indicator will indicate the strength of the distance 4 The sound of the Base unit will also give you an idea of how close you are to the object that is being tracked The faster the tone the closer you are Ideally every few seconds the mute button should be pressed to see if the object being tracked can be heard nearby as the Tag unit will also make a loud beeping sound 5 To stop searching simply press the search button again Note If and when the Base unit and Tag unit is out of range or blocked by buildings both units will go quiet Press and release working range 0 100m 300ft line of sight the exact dista
5. nce depends on the terrain environment 7 Notice In order to get good signal reception please don t hold this way it may reduce signal by your hand Place the Tag unit on a surface and practice locating it a few times to get a feel 2 If you are ever unsure of which direction to go slowly repeat a full 360 circle and then proceed in the direction with the strongest signal strength 3 When in search mode always place the Base unit in front of your chest turn your body slowly to find the correct direction 4 If the distance between the Base unit and Tag unit is out of detectable range both units will make a beeping sound every seconds as a reminder ALARM RANGE SETTINGS When both the wireless leash units activate the alarm that means the distance between the Base unit and Tag unit is at a certain distance These range settings can be adjusted to 4 zones Very close close medium and far default To change the range settings press the search button and follow the LED light indication to set the desired range Note Range can vary depending on environmental surrounding FindMe Function To activate the FindMe function just press and hold the FindMe LED light button on the Base unit The Tag unit will activate an alert beep to give a indication of where the other end of the wireless leash might be SLEEP MODE Always switch the Base unit off when not in use this will then have the Tag unit go into sleep mod
6. nd damage electronic circuit boards e Do not attempt to open the device other than as instructed in this guide f Do not drop knock or shake the device Rough handling can break internal circuit boards and fine mechanics g Do not use harsh chemicals cleaning solvents or strong detergents to clean the device h Do not paint the device paint can clog the moving parts and prevent proper operation i Do not put the master and the Slave at same place in case of this kit is unable playing functions to guard your pets j Search detection and alarm range depend on the terrain environment If the beep sound is not loud enough the batteries may be low Change with new batteries for louder alarm sound I This product only assists in providing a warning alarm to remind the user It does not guarantee to prevent theft or robbery of personal property m If you want to use the device during flight trips please comply with the flight safety law according to each country n We reserve the right in changing the specification of the hardware and software designs to manuals at any time and without prior notice Information in this document is subject to change without notice o This product operational temperature is between 40 F 104 F 5 C 40 C Storage Temperature is between 4 F 185 F 20 C 85 C o gt o Recycle The Batteries provided in this product should be recycled to protect the local environment Plea
7. se contact your local recycle department for detail Warning Do not put the batteries into the fire or heat sources It may cause danger or even explosion FCC CERTIFICATIONS Federal Communication Commission Interference Statement This equipment has been tested and improved to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This FCC Certifications equipment generates uses and can radiate radio frequency energy if installed and used not in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determinedly turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures m Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver m Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference
8. y mode press the Search Distance button Out of detection range Signal indication LED flashes Melody is slower and short RED light every second beep every second Mute the Base unit long press the LED button Keep showing the distanc 3 z desta a stance Mute temporarily nder standby mode switch the power Sleep button to OFF x x Wake Up pinder sleep mode switch the power signal indication LED flashes High beeps while re linking Base unit amp Tag unit are out of range Disconnect The connection range depends on the terrain environment Signal indication LED flashes RED light every second High beep every sesond Signal indication LED flashes A single beep sound every Battery low RED light every second 2 minutes CARE AND MAINTENANCE a Keep the device dry Precipitation humidity and all types of liquids or moisture can contain minerals that may corrode electronic circuits If your device gets wet remove the battery and allow the device to dry completely before replacing it Do not use or store the device in dusty dirty areas as its moving parts and electronic components can be damaged c Do not store the device in hot areas High temperatures can shorten the life of electronic device damage Batteries and warp or melt certain plastics d Do not store the device in cold areas When the device returns to its normal temperature moisture can from inside the device a
Download Pdf Manuals
Related Search