P1157S-871 User`s Manual VA1
Contents
1. All in One PANEL PC User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information Axiomtek Co Ltd assumes no responsibility for any infringements of patents or any third party s rights and any liability arising from such use Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of any information in this document Axiomtek does not make any commitment to update the information in this manual Axiomtek reserves the right to change or revise this document and or product at any time without notice No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Axiomtek Co Ltd CAUTION If you replace wrong batteries it causes the danger of explosion It is recommended by the manufacturer that you follow the manufacturer s instructions to only replace the same or equivalent type of battery and dispose of used ones Copyright 2014 Axiomtek Co Ltd All Rights Reserved Dec 2014 Version A1 Printed in Taiwan Safety Precautions Before getting started read the following important cautions 1 Be sure to ground yourself to prevent static charge when installing the internal components Use a grounding wrist strap and place all electronic component2. standard set of mounting kit included in the system packaging is needed Step 1 Unscrew the fix screws from the left and right side of the system Step 2 Fixing the rack mount bracket to the left and right of the system AMI BIOS Setup Ulility 13 P1157S 881 User s Manual 2 5 HDD Installation The P1157S 881 provides a convenient Hard Disk Drive HDD bracket for users to install 2 x 2 5 or 1 x 3 5 SATA HDD Please follow the steps Step 1 Refer section 2 1 to open the back cover Step 2 Unscrew 4 screws to take off the HDD bracket Step 3 Fix the HDD on bracket by the screws A 1 x 3 5 SATA HDD Kit A 1 x 2 5 or 2 x 2 5 SATA HDD Kit A Fix the 3 5 HDD on the back A Fix the 2 5 HDD on the right and left side of bracket bracket 14 AMI BIOS Setup Utility P1157S 881 User s Manual Step 4 Fix the HDD bracket into the main base Step 5 Plug the power and SATA cables to connectors Installation completes AMI BIOS Setup Utility 15 P1157S 881 User s Manual 2 6 DRAM Installation The P1157S 881 provides two 204 pin DDR3 SO DIMM socket that support system memory up to 16GB Please follow steps below to install the memory modules Step 1 Refer to section 2 1 to open the back cover and find out DIMM socket on mainboard MANOS71 d Bm iv D E CREE Im E Step 2 Push the latches on each side of the SO DIMM slot down 16 AMI BIOS Setup Utility P1
3. 157S 881 User s Manual Step3 Install the SO DIMM module into the slot and press it firmly down until it seats correctly Step4 The slot latches are levered upwards and latch on to the edges of the SO DIMM AMI BIOS Setup Utility 17 P1157S 881 User s Manual 2 7 CPU Installation The P1157S 881 has an LGA1155 socket supporting Intel 3 amp 2 Core i7 i5 i3 series Pentium and Celeron processors and provides high computing performance for users Step 1 Press the hook of lever down with your thumb and pull it to the right side to release it from retention tab Step 2 Lift the tail of the load lever and rotate the load plate to fully open position And remove the protective plastic cover 18 AMI BIOS Setup Utility P1157S 881 User s Manual Step3 CPU aims at the socket and places the package carefully into the socket by purely vertical motion W j V NOTE Never touch fragile socket contacts to avoid damage and do not touch processor sensitive contacts at any time during installation AMI BIOS Setup Utility 19 P1157S 881 User s Manual 2 8 CPU Cooler Installation Step 1 Making sure your CPU settled correctly on the socket Step2 Screw the cooling fan supporting base onto the CPU socket on the Motherboard and make sure the CPU fan is plugged to the CPU fan connector And Connect the CPU cooler power connector to the FAN1 connector 20 AMI BIOS Setup Utility P1157S 881 U
4. 25 025001 639 6020 5 609 6 500002005 0 0522 50009 0 2 009 04 05 iii Chapter 1 lIntroduction f 1 1 1 2 1 3 1 4 1 5 General Description P 1 le de e e 2 Dimensions and Kelt lu 4 fefe eR 5 PACKING NL T 6 Chapter 2 Hardware and Installation 7 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 2 9 2 10 Open back COVCE E Rn egen 8 Serial Ports Interface iun ee ases co aui Coca Co sse cp no EE en cuia eeu esa Oa PRESS 9 ENGINE EE 10 Mountings Panel Wall Rack Desktop VESA 11 2 4 1 VESA ARM Wall Mount Desktop mounmt 11 2 4 2 Panel MOunt I ibASSOmbly EE 12 2 4 3 Reine ug giri 13 HDD JristallatlOTizsii iie dins ica sane cod conus soa eund utet sanc od ua uisa Sea denas Aud b ua RR IUE 14 DRAM RIVE CHE e BE 16 RRE CIE de TEE 18 CPU Cooler Installation ssossissnxve nux Ex Rx Ucu ERE RUE xS Ux EuE UK DUIEEMEM MERE MEE UE E nan 20 Wireless LAN Module Installation optional 21 Fan Tunnel Installation esee 23 Chapter 3 AMI BIOS Setup Utility 25 3 1 3 2 3 3 3 4 3 5 3 6 3 7 3 8 3 9 Stanin Le ee 25 Menu Bar ouod EDDIE BE DEDE E SIE dE 26 NAVIGATION Mc 26 Maln Bd E UI et
5. Copyright C 2012 American Megatrends Inc Save Changes and Exit Save Changes and Exit When you select this option it will pop out the following message Save configuration changes and exit setup Select OK to save the changes and exit the UEFI setup utility Discard Changes and Exit When you select this option it will pop out the following message Discard changes and exit setup Select OK to exit the UEFI setup utility without saving any changes Discard Changes When you select this option it will pop out the following message Discard changes Select OK to discard all changes Load UEFI Defaults Load UEFI default values for all the setup questions F9 key can be used for this operation Launch EFI Shell from filesystem device Attempt to Launch EFI Shell application Shell64 efi from one of the available filesystem devices 44 AMI BIOS Setup Utility P1157S 881 User s Manual Chapter 4 Drivers Installation 4 1 System P1157S 881 supports Windows 7 and WES 7 To facilitate the installation of system driver please carefully read the instructions in this chapter before start installing Step 1 Insert Driver CD and select the Drivers Sp _ a _ we x 4 d Cu Step 1 Chipset Step 2 Graphic Step 3 LAN Step 4 USB 3 0 Step 5 ME Step 6 HD Audio _ Nu Step 7 COM Step 8 Touch Step 2 Select all files and follow the installing procedure 4 2 Touch Screen The P1157S 881 uses t
6. _FAN1 Setting This allows you to set CPU fan 1 s speed Configuration options are Full On and Automatic Mode The default value is Full On CHA_FAN1 Setting This allows you to set chassis fan 1 s speed Configuration options are Full On and Automatic Mode The default value is Full On Over Temperature Protection Use this to enable or disable Over Temperature Protection The default value is Enabled Case Open Feature This allows you to enable or disable case open detection feature The default value is Disabled Clear Status This option appears only when the case open has been detected Use this option to keep or clear the record of previous chassis intrusion status 40 AMI BIOS Setup Utility P1157S 881 User s Manual 3 7 Boot Menu In this section it will display the available devices on your system for you to configure the boot settings and the boot priority aptio Setup Utility Copyright C 2012 American Megatrends Inc Boot From Onboard LAN Use this item to enable or disable the Boot From Onboard LAN feature Setup Prompt Timeout This shows the number of seconds to wait for setup activation key 65535 O0XFFFF means indefinite waiting Bootup Num Lock If this item is set to On it will automatically activate the Numeric Lock function after boot up Boot Beep Select whether the Boot Beep should be turned on or off when the system boots up Please note that a buzzer is needed Full Screen Logo Use this
7. able or disable the S M A R T Self Monitoring Analysis and Reporting Technology feature Configuration options are Disabled and Enabled 34 AMI BIOS Setup Utility P1157S 881 User s Manual e Intel R Smart Connect Technology Aptio Setup Utility Copyright C 2012 American Megatrends Inc Intel R Smart Connect Technology Enabled Intel R Smart Connect Technology Use this item to enable or disable Intel R Smart Connect Technology Intel R Smart Connect Technology keeps your e mail and social networks such as Twitter Facebook etc updated automatically while the computer is in sleep mode The default is Enabled AMI BIOS Setup Utility 35 P1157S 881 User s Manual e Super lO Configuration Aptio Setup Utility Copyright C 2012 American Megatrends Inc gt COM1 Configuration COM1 Configuration Use this to set parameters of COM1 COM port type options are RS232 RS422 or RS485 COM2 Configuration Use this to set parameters of COM2 COM2 port type options are RS232 RS422 or RS485 COMSGS Configuration Use this to set parameters of COM3 COMS port type options are RS232 RS422 or RS485 COM4 Configuration Use this to set parameters of COM4 WDT Timeout Reset This allows users to enable disable the Watchdog timer timeout to reset system The default value is Disabled 36 AMI BIOS Setup Utility P1157S 881 User s Manual e ACPI Configuration aptio Setup Utilitu Copyright C 2012 Am
8. bbrstion dets Standard Calbration Acherced Calbeeter Tuam off EEPROM storage Step 5 Calibrations To adjust the display with touch panel click Calibration and follow the calibrate point to do calibration there are five points on screen for calibration a i Touch the rad square Step 6 Press OK Drivers Installation 47 P1157S 881 User s Manual 4 3 Embedded O S The P1157S 881 provides the Windows 7 Embedded The O S is supported devices which are listed below e WEG Here are supported onboard devices ii Onboard Multi I O B SATA HDD B USB E PS2 Keyboard and mouse E CRT LCD display g 10 100 1000 base T Ethernet m Onboard Audio E Touch Screen PenMount Touch screen Before you can use and calibrate it here is what you should do 1 Set up Penmount touch device driver by executing C Penmount Windows 2000 XP V5 0 setup exe When the installation is finished an icon PM appears on the Taskbar 2 Calibrate Penmount touch by clicking on the PM icon and the go on the calibration 3 Restart the computer 48 Drivers Installation
9. e on your screen AMI BIOS Setup Utility 25 P1157S 881 User s Manual 3 2 Menu Bar The top of the screen has a menu bar with the following selections Mein To set up the system time date information To set up the advanced BIOS features Em Toestth cunt sereen or me 10S soup uy Use key or lt gt gt key to choose among the selections on the menu bar and then press Enter to get into the sub screen You can also use the mouse to click your required item 3 3 Navigation Keys The BIOS setup utility uses a key based navigation system called hot keys Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process These keys include F1 F7 Enter lt ESC gt Arrow keys and so on EQ Some of the navigation keys differ from one screen to another Note Please check the following table for the function description of each navigation key gt Left Right The Left and Right lt Arrow gt keys allow you to select a setup screen Up Down The Up and Down lt Arrow gt keys allow you to select a setup screen or sub screen The Plus and Minus lt Arrow gt keys allow you to change the field value of a Plus Minus particular setup item The lt Enter gt key allows you to display or change the setup option listed for a particular setup item The lt Enter gt key can also allow you to display the setup sub screens The lt F1 gt key allo
10. el USB 3 0 mode Legacy USB Support Use this option to select legacy support for USB devices There are four configuration options Enabled Auto Disabled and UEFI Setup Only The default value is Enabled Please refer to below descriptions for the details of these four options Enabled Enable support for legacy USB Auto Enable legacy support if USB devices are connected Disabled USB devices are not allowed to use under legacy OS and UEFI setup when Disabled is selected If you have USB compatibility issues it is recommended to select Disabled to enter OS UEFI Setup Only USB devices are allowed to use only under UEFI setup and Windows Linux OS Legacy USB 3 0 Support Use this option to enable or disable legacy support for USB 3 0 devices The default value is Enabled 38 AMI BIOS Setup Utility P1157S 881 User s Manual e Voltage Configuration Aptio Setup Utility Copyright C 2012 American Megatrends Inc DRAM Voltage BUS DRAM Voltage Use this to select DRAM Voltage The default value is 1 50V AMI BIOS Setup Utility 39 P1157S 881 User s Manual 3 6 H W Monitor Menu In this section it allows you to monitor the status of the hardware on your system including the parameters of the CPU temperature motherboard temperature CPU fan speed chassis fan speed and the critical voltage Aptio Setup Utility Copyright C 2012 American Megatrends Inc CPU FAN1 Setting Full 0n CPU
11. erican Megatrends Suspend to RAM Auto Suspend to RAM Use this item to select whether to auto detect or disable the Suspend to RAM feature Select Auto will enable this feature if the OS supports it Check Ready Bit Use this item to enable or disable the feature Check Ready Bit ACPI HPET Table Use this item to enable or disable ACPI HPET Table The default value is Enabled Please set this option to Enabled if you plan to use this motherboard to submit Windows certification PS 2 Keyboard Power On Use this item to enable or disable PS 2 keyboard to turn on the system from the power soft off mode PCI Devices Power On Use this item to enable or disable PCI devices to turn on the system from the power soft off mode Wake From Onboard LAN 2 Use this item to enable or disable the Wake From Onboard LAN 2 feature RTC Alarm Power On Use this item to enable or disable RTC Real Time Clock to power on the system USB Keyboard Remote Power On Use this item to enable or disable USB Keyboard Remote to power on the system AMI BIOS Setup Utility 37 P1157S 881 User s Manual USB Mouse Power On Use this item to enable or disable USB Mouse to power on the system e USB Configuration Aptio Setup Utility Copyright C 2012 American Megatrends Inc USB Controller Enabled USB Controller Use this item to enable or disable the use of USB controller Intel USB 3 0 Mode Use this item to enable or disable the use of Int
12. he 5 wire analog resistive There are the specification and driver installation which are listed below e Specification Touch Screen 5 wire Analog Resistive type Touch Screen Controller PenMount 6500 USB Touch Screen Controller IC Communications USB interface Baud Hate 19200 baud rate fixed Hesolution 1024 X 1024 Drivers Installation 45 P1157S 881 User s Manual e Driver Installation Windows 7 The P1157S 881 provides a touch screen driver that users can install it under the operating system Windows 7 To facilitate installation of the touch screen driver you should read the instructions in this chapter carefully before you attempt installation Step 1 Insert Driver CD and follow the path to select the Drivers Step 6 Touch Driver Utility A 1 e Setup Setup Step 2 Follow the installing procedure and press OK Step 3 Click Start menu and select PenMount Utilities and then a PenMount Control Panel pops out PenMount Control Panel Device Multiple Moritors Tools About E Penmourt Control Panel Version 1 0 0 63 Installed Device s Device 0 Pen ourt 6500 L58 Suppcrt E mal pe mountio esed ne lw Support Website nite Ives penmaunt com tw 46 Drivers Installation P1157S 881 User s Manual Step 4 Select the Standard Calibrate tab AP Device 0 Pentdount 6500 USR Cs Erase Setting Edge Compensation About Advanced Moce 9 o Ekt ca
13. item to enable or disable OEM Logo The default value is Enabled CSM Please disable CSM when you enable Fast Boot option The default value is Enabled AMI BIOS Setup Utility 41 P1157S 881 User s Manual aptio Setup Utility Copyright C 2012 American Megatrends Inc Enabled CSM Enable to launch the Compatibility Support Module Please do not disable unless you re running a WHCK test If you are using Windows 8 64 bit and all of your devices support UEFI you may also disable CSM for faster boot speed Launch PXE OpROM Policy Select UEFI only to run those that support UEFI option ROM only Select Legacy only to run those that support legacy option ROM only Launch Storage OpROM Policy Select UEFI only to run those that support UEFI option ROM only Select Legacy only to run those that support legacy option ROM only Launch Video OpROM Policy Select UEFI only to run those that support UEFI option ROM only Select Legacy only to run those that support legacy option ROM only 42 AMI BIOS Setup Utility P1157S 881 User s Manual 3 8 Security Menu In this section you may set change or clear the supervisor user password for the system aptio Setup Utility Copyright C 2012 American Megatrends Inc Supervisor Password Secure Boot Use this to enable or disable Secure Boot The default value is Disabled AMI BIOS Setup Ulility 43 P1157S 881 User s Manual 3 9 Exit Menu Aptio Setup Utility
14. l configured parameters are stored in a flash chip to save the setup information whenever the power is turned off This chapter provides users with detailed description about how to set up basic system configuration through the AMI BIOS setup utility 3 1 Starting To enter the setup screens follow the steps below 1 Turn on the computer and press F2 or Del during the Power On Self Test POST to enter BIOS setup otherwise POST will continue with its test routines 2 After you press the Del key the main BIOS setup menu displays You can access the other setup screens from the main BIOS setup menu such as the Advanced and Chipset menus If your computer cannot boot after making and saving system changes with BIOS setup you can restore BIOS optimal defaults by setting CLRCMOS 1 see section Note 2 3 1 If you wish to enter BIOS setup after POST restart the system by pressing lt Ctrl gt lt Alt gt Delete or by pressing the reset button on the system chassis You may also restart by turning the system off and then back on It is strongly recommended that you should avoid changing the chipset s defaults Both AMI and your system manufacturer have carefully set up these defaults that provide the best performance and reliability Because the BIOS setup software is constantly being updated the following setup screens and descriptions are for reference purpose only and they may not exactly Note match what you se
15. led Restore on AC Power Loss This allows you to set the power state after an unexpected AC power loss If Power Off is selected the AC power remains off when the power recovers If Power On is selected the AC power resumes and the system starts to boot up when the power recovers Active LVDS Use this to enable or disable the LVDS The default value is Enabled Primary IGFX Boot Display Select the video device which will be activated during POST This has no effect if external graphics present Secondary boot display selection will appear based on your selection VGA modes will be supported only on primary display Configuration options are VBIOS Default CRT DVI HDMI and LVDS The default value is VBIOS Default AMI BIOS Setup Utility 33 P1157S 881 User s Manual e Storage Configuration Aptio Setup Utility Copyright C 2012 American Megatrends Inc SATA Controller s Enabled SATA Controller s Use this item to enable or disable the SATA Controller feature SATA Mode Selection Use this to select SATA mode Configuration options are IDE Mode AHCI Mode and RAID Mode The default value is AHCI Mode Ed AHCI Advanced Host Controller Interface supports NCQ and other new features that will improve SATA disk performance but IDE mode does not Note have these advantages SATA Aggressive Link Power Mgmt Use this item to configure SATA Aggressive Link Power Management Hard Disk S M A R T Use this item to en
16. nc Active Processor Cores Active Processor Cores Select the number of cores to enable in each processor package CPU C States Support Enable CPU C States Support for power saving It is recommended to keep C3 C6 and C7 all enabled for better power saving Enhanced Halt State C1E Enable Enhanced Halt State C1E for lower power consumption CPU C3 State Support Enable C3 sleep state for lower power consumption CPU C6 State Support Enable C6 deep sleep state for lower power consumption CPU C7 State Support Enable C7 deep sleep state for lower power consumption Package C State Support Enable CPU PCI Express Memory Graphics C State Support for power saving 30 AMI BIOS Setup Utility P1157S 881 User s Manual Intel SpeedStep Technology Intel SpeedStep technology is Intel s new power saving technology Processors can switch between multiple frequencies and voltage points to enable power saving The default value is Enabled Configuration options are Enabled and Disabled If you install Windows 7 8 and want to enable this function please set this item to Enabled This item will be hidden if the current CPU does not support Intel SpeedStep technology Please note that enabling this function may reduce CPU voltage and lead to system stability or compatibility issues with some power supplies Please Note set this item to Disabled if above issues occur Intel Turbo Boost Technology Use this item to enable or di
17. ot find the package or any items are missing please contact Axiomtek distributors immediately 6 Introduction P1157S 881 User s Manual Chapter 2 Hardware and Installation The P1157S 881 provides rich I O ports and flexible expansions for you to meet different demand The chapter will show you how to install the hardware It includes Open back cover Serial Port Interface Ethernet Mounting Method Hard disk DRAM CPU CPU Cooler Wireless LAN Module optional Fan tunnel AMI BIOS Setup Utility 7 P1157S 881 User s Manual 2 1 Open back cover This section tells users how to open back cover Please follow the steps below Step 1 Unscrew 3 screws on the back cover and push to the right side Please refer the photo below Step 2 Remove the back cover and unscrew 2 screws 3 t em AMI BIOS Setup Utility P1157S 881 User s Manual 2 2 Serial Ports Interface This motherboard supports RS 232 422 485 on COM1 COMS ports and 1 x RS 232 COMA The pin assignments are listed in table below If you need to adjust these COM ports to work as RS 232 422 485 please refer to BIOS setting in section 5 4 Pin RS 232 Jm RS 485 6 osmomasemea WA NA s To cieartosend WA wa s No Powerievierev WA NA AMI BIOS Setup Utility 9 P1157S 881 User s Manual 2 3 Ethernet The P1157S 881 is equipped with two high performance plug and play Ethernet in
18. pter This allows you to select Onboard or PCI Express as the boot graphic adapter priority The default value is PCI Express VT d Use this to enable or disable Intel VT d technology Intel Virtualization Technology for Directed IO The default value of this feature is Disabled PCIE1 Link Speed Select the link speed for PCIE1 Share Memory Configure the size of memory that is allocated to the integrated graphics processor when the system boots up IGPU Multi Monitor Select Disabled to disable the integrated graphics when an external graphics card is installed Select Enabled to keep the integrated graphics enabled at all times 32 AMI BIOS Setup Utility P1157S 881 User s Manual Render Standby Use this to enable or disable Render Standby by Internal Graphics Device The default value is Enabled Onboard HD Audio oelect Auto Enabled or Disabled for the onboard HD Audio feature If you select Auto the onboard HD Audio will be disabled when PCI Sound Card is plugged Front Panel Select Auto or Disabled for the onboard HD Audio Front Panel Onboard HDMI HD Audio This allows you to enable or disable the Onboard HDMI HD Audio feature Onboard LAN1 This allows you to enable or disable the Onboard LAN1 feature Onboard LAN2 This allows you to enable or disable the Onboard LAN feature Deep Sleep Mobile platforms support Deep S4 S5 in DC only and desktop platforms support Deep 84 85 in AC only The default value is Disab
19. reen to go to the sub menus CPU Configuration Chipset Configuration Storage Configuration Intel R Smart Connect Technology Super IO Configuration ACPI Configuration USB Configuration Voltage Configuration Instant Flash VVVVVVVVYV Aptio Setup Utility Copyright C 2012 American Megatrends Inc gt CPU Configuration For items marked with gt please press lt Enter gt for more options K a Setting wrong values in this section may cause the system to malfunction Note 28 AMI BIOS Setup Utility P1157S 881 User s Manual Instant Flash Instant Flash is a UEFI flash utility embedded in Flash ROM This convenient UEFI update tool allows you to update system UEFI without entering operating systems first like MS DOS or Windows Just launch this tool and save the new UEFI file to your USB flash drive floppy disk or hard drive then you can update your UEFI only in a few clicks without preparing an additional floppy diskette or other complicated flash utility Please be noted that the USB flash drive or hard drive must use FAT32 16 12 file system If you execute Instant Flash utility the utility will show the UEFI files and their respective information Select the proper UEFI file to update your UEFI and reboot your system after UEFI update process completes AMI BIOS Setup Utility 29 P1157S 881 User s Manual e CPU Configuration Aptio Setup Utility Copyright C 2012 American Megatrends I
20. s in any static shielded devices Most electronic components are sensitive to static electrical charge Disconnect the power cords from the NA 550 Series before making any installation Be sure both the system and the external devices are turned OFF Sudden surge of power could ruin sensitive components Make sure the NA 550 Series is properly grounded Do not open the system s top cover If opening the cover for maintenance is a must only a trained technician is allowed to do so Integrated circuits on computer boards are sensitive to static electricity To avoid damaging chips from electrostatic discharge observe the following precautions a Before handling a board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds This will help to discharge any static electricity on your body m When handling boards and components wear a wrist grounding strap available from most electronic component stores Trademarks Acknowledgments Axiomtek is a trademark of Axiomtek Co Ltd Windows is a trademark of Microsoft Corporation IBM PC AT PS 2 VGA are trademarks of International Business Machines Corporation Intel and Pentium are trademarks of Intel Corporation AMI is trademark of American Megatrend Inc Other brand names and trademarks are the properties and registered brands of their respective owners T able of Contents BIER Elte TRO ji Salety PRECAUTION S 2 2 2 925 0
21. sable Intel Turbo Boost Mode Technology Turbo Boost Mode allows processor cores to run faster than marked frequency in specific conditions The default value is Enabled CPU Thermal Throttling You may select Enabled to enable CPU internal thermal control mechanism to keep the CPU from overheating No Execute Memory Protection No Execution NX Memory Protection Technology is an enhancement to the IA 32 Intel Architecture An IA 32 processor with No Execute NX Memory Protection can prevent data pages from being used by malicious software to execute codes This option will be hidden if the current CPU does not support No Execute Memory Protection Intel Virtualization Technology When this option is set to Enabled a VMM Virtual Machine Architecture can utilize the additional hardware capabilities provided by Vanderpool Technology This option will be hidden if the installed CPU does not support Intel Virtualization Technology Hardware Prefetcher Use this item to turn on off the MLC streamer prefetcher Adjacent Cache Line Prefetch Use this item to turn on off prefetching of adjacent cache lines AMI BIOS Setup Utility 31 P1157S 881 User s Manual e Chipset Configuration aptio Setup Utility Copyright C 2012 American Megatrends Inc DRAM Frequency DRAM Frequency If Auto is selected the motherboard will detect the memory module s inserted and assign the appropriate frequency automatically Primary Graphics Ada
22. ser s Manual 2 9 Wireless LAN Module Installation optional The P1157S 881 provides one wireless LAN module to install When installing the wireless LAN module refer to the following instructions and illustration Step 1 Refer to section 2 1 to open the back cover and find out the wireless LAN module located Step 2 Fixing the wireless LAN module by 2 screws AMI BIOS Setup Utility 21 P1157S 881 User s Manual Step 3 Plug in USB cable to the connector of WIFI module And find the built in Antenna cable and connect it wireless LAN card EES d ex 2 WN90Z1Y8NM XAd QI 994 Step4 Lift the rubber stopper from the top of back cover Step 5 Install the antenna on the antenna connector 22 AMI BIOS Setup Utility P1157S 881 User s Manual 2 10 Fan Tunnel Installation The P1157S 881 provides one fan tunnel to install When installing the fan tunnel refer to the following instructions and illustration Step1 Spread the fan tunnel out flat Step2 Tear the releasing paper from the dual face tape Step3 Fold each curved line Step4 Stick each side together AMI BIOS Setup Utility 23 P1157S 881 User s Manual Step5 Let fan cable through the fan tunnel and stick to the cooler 24 AMI BIOS Setup Utility P1157S 881 User s Manual Chapter 3 AMI BIOS Setup Utility The AMI UEFI BIOS provides users with a built in setup program to modify basic system configuration Al
23. sing e Power Input m 100 240VAC power connector amp y Y NOTE 1 All specifications and images are subject to change without notice 2 Long press the button of OSD doesn t have repeat function 3 Because of issue of Intel H81 chipset Display Port Aux the errors will be occurred in LCD display Please restart the system if the error happened Introduction 3 P1157S 881 User s Manual 1 3 Dimensions and Outlines The following diagrams show the dimensions and outlines of P1157S 881 73 26 113 9 113 4 73 36 368 ak CUTOUT Dim 4 Introduction P1157S 881 User s Manual 1 4 UO Outlets Please refer to the following illustration for I O locations of the P1157S 881 7 1 2 34 5 1 x RS 232 422 485 with 5V amp 12V COM 1 x RS 232 422 485 with 5V amp 12V COM2 1 x RJ45 for GIGA Ethernet CAN 1 x RJ45 for GIGA Ethernet LAN2 1 x RS 232 with 5V amp 12V COM4 1 x HDMI 1 x RS 232 422 485 with 5V amp 12V COM3 1 x VGA 2 x USB3 0 2 x USB2 0 1 x MIC in 1 x Line out 2 x USB2 0 1 x AC Plug 1 x switch for power on off Introduction P1157S 881 User s Manual 1 5 Packing List When you receive the P1157S 881 the bundled package should contain the following items P1157S 881 unit x 1 Driver CD x1 Panel mount kit x 6 Wall VESA mount kit x 1 optional Rack mount kit x 1 optional Power cord x 1 If you can n
24. te rrt 27 Advanced Menlo se vivus c chet E dbsa us uc deca eta E ERE dERg VEU tts 28 FW MONRO MENMU Sorrisi ere yS PE Loewe ve a Roa enEEvE us eoyE eee 40 Giele dd clas EE 41 EECHELEN EE 43 Exit ITU 44 Chapter 4 Drivers Installation 45 ar E ET WEE 45 12 TOUCM SCIES EEN 45 43 Embedded EE 48 This page is intentionally left blank vi P1157S 881 User s Manual Chapter 1 Introduction This chapter contains general information and detailed specifications of the P1157S 881 Chapter 1 includes the following sections r e General Description e Specification e Dimensions e JO Outlets o Package List 1 1 General Description The P1157S 881 adopts a 15 inch XGA TFT LCD with 250 nits brightness and Intel 4 Core i7 i5 i3 series Pentium and Celeron processors and Intel H81 chipset to provide excellent and powerful computing performance Furthermore P1157S 881 adopts built in speaker and option WLAN module for wireless connectivity Industrial grade front bezel P1157S 881 adopts industrial grade material front bezel which incorporates the advantages of light weight high degree of hardness better heat releasing easy to shape and anti corrosion ability Therefore P1157S 881 is especially suitable for most rugged industrial environments Speaker and WLAN Antenna Supported P1157S 881 features built in speakers for kiosk application to display multimedia content program It also s
25. terfaces RJ 45 which are fully compliant with the IEEE 802 3 standard Connection can be established by plugging one end of the Ethernet cable into this RJ 45 connector and the other end to a 1000 100 10 Base T hub There are two LEDs next to the LAN port Please refer to the table below for the LAN port LED indications ACT LINK SPEED LAN Port LED Indications LED LED Activity Link LED SPEED LED Status Description Status Description 10Mbps connection Blinking Data activity 100Mbps connection Gbps connection LAN Port 10 AMI BIOS Setup Utility P1157S 881 User s Manual 2 4 Mountings Panel Wall Rack Desktop VESA There are 5 application options for the P1157S 881 including Panel Wall Rack Desktop VESA mounting ways 2 4 1 VESA ARM Wall Mount Desktop mount The P1157S 881 provides VESA mount 75x75 mm or 100x100mm Screw six screws to fix the kit in the back chassis A VESA Wall mount bracket A Putting the bracket on the back of system P1157S 881 User s Manual A Fixing the bracket by six screws on the left and right side 2 4 2 Panel mount Kit Assembly The P1157S 881 is designed for panel mount application To mount the P1157S 881 the standard set of mounting kit included in the system packaging is needed 12 AMI BIOS Setup Utility P1157S 881 User s Manual 2 4 3 Rack mount Kit Assembly The P1157S 881 is designed for rack mount application To mount the P1177S 871 the
26. upports WLAN module optional antenna for wireless network connectivity Introduction 1 P1157S 881 User s Manual Powerful computing Intel amp 3rd Generation Core i7 i5 i3 Celeron processors P1157S 881 features Intel 4th Core i7 i5 i3 series Pentium and Celeron processors and Intel H81 chipset which deliver high computing performance capability Haswell CPU offers reliable and stable performance and rugged environment 1 2 Specifications Main CPU Board e CPU B Intel 4th Core 17 15 13 series Pentium and Celeron processors e System Chipset m Intel H81 Express Chipset e System Memory gm 2x204 pin DDR3 1600 1333 MHz SO DIMM socket m Supporting 8GB per dimm maximum memory up to 16GB e BIOS m America Megatrends BIOS I O System e Standard UO m 3x RS 232 422 485 with 5V amp 12V 1 x RS 232 with 5V 12V gm 4x USB 2 0 gm 2x USB3 0 gm 1xHDMI gm 1x VGA e Ethernet m 2x RJ45 for Giga Ethernet e Audio m 1 x Line out m 1x Mic in e Expansion m 1x Wireless Module optional e Storage gm 2x2 5 or1x3 5 SATA HDD e Power connector m 1xAC plug D Introduction P1157S 881 User s Manual System Specification e 15 XGA 1024 X 768 LCD e 5 wired resistive Touch e IP65 NEMA4 aluminum front bezel e IP65 aluminum front bezel e Net Weight m 5 6 Kgs 12 35 Ib e Dimension Main Body Size B 378 x 72 x 309mm e Operation Temperature m OCto45C e Relative Humidity m 10 to 95 40C Non Conden
27. ws you to display the General Help screen Discard changes The F9 key allows you to load optimal default values for all the settings The lt F10 gt key allows you to save any changes you have made and exit Setup Press the lt F10 gt key to save your changes The Esc key allows you to discard any changes you have made and exit the Setup Press the Esc key to exit the setup without saving your changes 26 AMI BIOS Setup Utility P1157S 881 User s Manual 3 4 Main Menu When you first enter the setup utility you will enter the Main setup screen You can always return to the Main setup screen by selecting the Main tab System Time Date can be set up as described below The Main BIOS setup screen is shown below aptio Setup Utility Copyright C 2012 American Megatrends Inc System Date rem LI BIOS Information Display the auto detected BIOS information System Date Time Use this option to change the system time and date Highlight System Time or System Date using the Arrow keys Enter new values through the keyboard Press the Tab key or the Arrow keys to move between fields The date must be entered in MM DD YY format The time is entered in HH MM SS format AMI BIOS Setup Utility 27 P1157S 881 User s Manual 3 5 Advanced Menu The Advanced menu also allows users to set configuration of the CPU and other system devices You can select any of the items in the left frame of the sc
Download Pdf Manuals
Related Search