English - Shopify
Contents
1. IHN 4 J In Step 5 Attach the Tilt Knobs With your TV mounted to the wall plate insert the Safety Knobs N through Spring Washer P and Washer J then through the mounting slot on the TV Bracket and into the threaded holes on the Arm Assembly as shown in Diagram F You can then tilt the TV 12 to your desired viewing angle tighten the Safety Knobs and pan the TV approximately 30 in either direction Your installation is complete If preferred you can use the supplied Allen Bolts O in place of the Safety Knobs N if you do not plan to use the tilt function regularly WARNING Use two people to lift and position the TV onto the Wall Plate Kanto Hook Kanto as Check out more great products from Kanto Kanto YARO Speaker System Our stunning new audio system designed for Apple TV e Utilizing audio technology by Bang amp Olufsen ICEpower 100 watts of pure clean sound Optional 200 watt sub woofer Visit kantospeakers com for more Kanto Infinity Series Cables 3D and 1080p HD Full Colour Capabilities e 24 kt gold plated contacts Metal head connectors with flex relief and grip e HDMI Ethernet Channel For more TV and desktop mounts along with our other products please visit kantoav com LIKE Kanto on Facebook to receive upcoming news and special product offers Supporting your digital lifestyle Warranty Limited Warr2. 4 231 9574 Fax 604 231 9535
3. English User Manual L100 TV Mount Supporting your digital lifestyle Table of Contents Table of Contents Introduction 2 Setup Steps 3 to 5 3 Y YU YY YY 6 Supplied Parts amp Hardware 3 Other Kanto Products envers 7 Setup Step llu iau Gudd dd ddd dU 4 Warnane ec oo an 8 ss 119 hes FFR oe ee 5 Introduction Thank you for choosing a Kanto AV Systems tilting wall mount The L100 is designed to mount flat panel televisions weigh ing up to 56 lbs 25 kg within 3 of your wall allow you to swivel left and right approximately 30 depending on TV size and tilt your TV 2122 Read these instructions fully before installation of this mount If you do not understand these directions or have any doubts about the safety of the installation please consult a qualified installation contractor to install this mount Make sure there are no defective or missing parts Do not use defective parts If you are uncertain whether the part is defective call Kanto AV Systems directly at 1 888 848 2643 or support kantoav com Kanto AV Systems can not be liable for property damage or injury caused by incorrect mounting incorrect assembly lifting or incorrect use of this product This product should not be mounted on steel stud walls or cinder block walls Consult a qualified installation contractor if you are unsure about the type of wall you may have We make every e
4. Step 2 Mount Wall Plate Wood Stud Wall The Wall Plate must be mounted to a wood stud Use a stud sensor to locate the stud clearly marking the outer edges of the stud Align the Wall Plate with the Stop Screw at the bottom of the plate see Diagram B so that all four screws will screw into the stud and mark the top hole Pre drill the top hole then temporarily attach the Wall Plate to the wall using a Lag Bolt L Using a level ensure that the Wall Plate is level and mark the three remaining holes Remove the Wall Plate and drill the remaining holes Attach the Wall Plate using 4 Lag Bolts L see Diagram B Do not over tighten lag bolts L Make sure the Wall Plate is flat against the wall surface Wood eon NN 5 32 4mm A i _ r L E ie l ae A 4 N sy _ es Vf Ep Th oo at bottom 1 as LS Diagram B CAUTION Make sure the supporting surface will support the load limits outlined in the Caution at bottom of page two Tighten Lag Bolts until the Wall Plate is snug flat against the wall Do not over tighten Lag Bolts L Each Lag Bolt must be screwed into a wood stud at bottom i em ASH Brick or Concrete Wall Using the Wall Plate as a template with the Stop Screw at the bottom of the plate see Diagram C use a level to ensure that the Wall Plate is level then mark
5. anty To Original Purchaser Kanto AV Systems Kanto warrants the equipment it manufactures to be free from defects in material and workmanship for the following limited warranty period of 24 months parts and labour If equipment fails because of such defects and Kanto or an authorized dealer is notified within 24 months from the date of shipment with proof of original invoice Kanto will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the repair Such repairs are warranted for 90 days from the day of reshipment to the original purchaser This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed The information in the owner s manual has been carefully checked and is believed to be accurate However Kanto assumes no responsibility for any inaccuracies that may be contained in the manual In no event will Kanto be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages ka N KO g lt www kantoav com sales kantoav com o AD Tel 60
6. ffort to ensure all necessary hardware is included If there is hardware missing please call Kanto AV Systems directly at 1 888 848 2643 or support kantoav com See installation video online at www kantoav com pages video l100 CAUTION The maximum loading weight is 56 Ibs 25 kg This wall mount is intended for use only within the maximum weight restrictions indicated Use with products heavier than the maximum weights indicated may result in instability causing possible injury Recommended TV Size 19 inch to 32 inch CAUTION The wall you plan to affix the Kanto mount to must be able to support more than 5 times the weight of the television and the wall mount combined Do not use this product for any purpose other than to mount a flat panel TV on a vertical surface as outlined in this manual Improper installation may cause damage to your TV or serious injury This product should not be mounted to steel stud walls cinder block or old concrete walls Consult a gualified installation contractor if you are unsure about the type of wall you may have kanto Supplied Parts and Hardware A Wall Plate B Arm Assembly C TV Plate D Screw Cover x4 x4 t SS E M4 x 12mm F M4 x 30mm G M6 x 12mm Screw Screw Screw Screw xg x6 CO x4 l M4 Washer J M6 Washer K Plastic Spacer L Lag Bolt o X x2 x2 x2 aw Y O M Concrete Anchor N Safety Knob O Allen Bolt P Spring Washer Reg
7. the four holes at your desired height Adjust the Wall Plate position to be clear of mortar joints Pre drill four holes and insert a Concrete Anchor M into each of the holes flush with the concrete wall surface and not flush with the surface covering such as drywall Attach the Wall Plate using 4 Lag Bolts L see Diagram C Make sure the Wall Plate is flat against the wall surface Do not over tighten Lag Bolts L Concrete t M 5 16 8mm L IR RSR oe Le L em em Diagram C CAUTION Make sure the concrete or brick wall is at least 2 thick Make sure the anchor is seated completely flush with the concrete surface even if there is another layer of material such as drywall If drywall is over 5 8 thick custom lag bolts must be used Concrete must be a minimum of 2000psi in density Supporting your digital lifestyle CAUTION Read this section carefully prior to install ee Step 3 Insert Arm Assembly iil oreo into Wall Plate Assemble the Arm Assembly and Screw Cover then slide __ e A the two parts together into the channel on the Wall Plate as shown in Diagram D The Arm Assembly will stop when it hits the Stop Screw Diagram D Step 4 Attach TV to Wall Plate Lift the TV on to the Wall Plate hooking the TV Plate on to the pegs of the Arm Assembly as shown in Diagram E LT i
8. uired Tools e 5 32 wood drill bit e hammer for concrete installs e 5 16 masonry bit for concrete installs carpenter s level e Phillips screwdriver e stud finder Q Allen Key Supporting your digital lifestyle Step 1 Attach TV Plate There are a wide variety of TVs available offering an assortment of screw sizes We provide a selection of mounting screws to fit most TVs If you have any concerns about this mounting hardware or installation call us direct at 1 888 848 2643 or email at support kantoav com Step 1 1 Select the correct size of bolt Kanto provides 2 bolt diameters Metric sizes M4 and M6 in various lengths Part items E F G H Select the correct diameter screw and hand screw into the back of the TV to determine the correct length Use the longest available bolt without reaching the bottom of the TV threads using spacers K if your TV has a curved back Spacer K if necessary for curved TVs Washer I or J Screws E thru H NS Step 1 2 Attach TV plate to the back of the TV Now that you have selected the correct bolt length it s time to attach the TV plate to the TV as shown in Diagram A Use the appropriate sized washer I or J as shown For curved back TVs use the spacers K Diagram A WARNING A Never over tighten a screw into the back of your flat panel TV Do not lay the TV face down on its glass front Use a wall or a TV stand Kanto
Download Pdf Manuals
Related Search