Home

Intellect

1. Intellect system is reflected on Fig 1 and Fig 2 Uploading of control panel DLK integration modules interact with standard access objects existing in Intellect system corresponding necessary information is received from settings of these objects during uploading of control panels Programming tab Dates of holidays are loaded from General settings section Later they will be taken into account if time zones have time intervals with holidays included refer to Time zone section Time zone section serves for specifying of schedules Set of time intervals assigns schedule according to which access 1s granted Access levels section serves as connecting link between schedules doors and users Access level assigns rule of access to particular door according to indicated schedules and then created access level can be assigned to user or department Users tab This section purposes for adjusting of access persons For the purpose of convenience users are divided into departments specified access level of department may be used by each user of the department General access level is specified for user Control panel generates table of used cards from settings of User objects borrowing the following data Permanent card Temporary card Valid till PIN code and User blocked flag Common settings holidays ACS Golden Gate iG oe configuration
2. a Create objec T Pe ee UL it Ic t Red ae Create object 5 Bolig OMAE l Modem connection ACS Golden Gate Security Zone l Disable ace aaa ee gaa na a Create folder Alarm Message Window User name 1 Move to folder amp Archive Disks to store archive Password Find m Audio Card i M Autetogtoad as ii T hp zi Te Controller Apollo Flops F Auto Log Backup l External plates database a HA En nterface sd i a E HDK Intert C E a ay pig keyboard ARA E Mal Message Service E o POS terminal S E a Panel Rubeg Q Short Message Service a Telemetry Card mt Video Capture Card Web server VideoServer Fig 3 Creating Golden Gate access control system This object is associated with RS 485 bus and corresponding COM port In Golden Gate ACS settings see Fig 4 choose COM port that has LNET interface converter connected Drop down list contains only ports available in operating system Further specify compatibility parameters used These parameters will influence the on behaviour of all subordinate objects Type of reader determines type of cards which are used on the object Wiegand42 specifies use of 5 byte card codes Wiegand26 of 3 byte card codes NOTE This parameter must be agreed with hardware settings of readers used on the object By default readers of Integrated Technical Vision manufacture operate in Wiegand42 mode If it is
3. l Time zones Loading REFI D Controller DLK B4 i Access levels Door DLK gi i Departments Fig 1 Common structure of DLK modules integration Loading Object code field is not used directly but it will be added to beginning of card code permanent or temporary if they are set Length of object code must coincide with Object code length field in Golden Gate ACS settings for the possibility of back reconversion of full card code into twain object code and card code when card events arise If the lengths do not coincide reconversion will not cast to original data and Intellect system will not be able to identify card user object code and card code will be indicated in event instead of user name Length of full card code object code length card code length must coincide with length of cards identificators of types used for access Wiegand26 Wiegand42 type of cards is specified in Golden Gate ACS settings that 1s 6 hexadecimal digits for Wiegand26 and 10 digits for Wiegand42 Maximum length of PIN code is six decimal numbers but code itself may be shorter PIN code supplements identification of user by card if PIN code field is marked control panel waits for PIN entering after card temporary or permanent presentation If User blocked flag is set card either temporary or permanent will be blocked For providing access user should necessarily have eithe
4. 09 10 11 12 peak amount 1S exceeded corresponding door goes into alarm Presentation of enrolled card clears the counter of card matching attempts If the amount is set to 0 card matching attempts will not be traced Fig 7 Dialog of quering for available controllers Wait for PIN code if there exists PIN code field in user settings reader will wait after card enrollment for PIN code entering to confirm access identity If Wait for PIN code field is set to 0 seconds control panel will wait for PIN code entering without time limit NOTE this time parameter should be long enough for any user having access rights to have time to enter PIN code Otherwise time will elapse before PIN code entering control panel will deny access and it will be necessary to pass card to reader and enter PIN code once again Double door flag indicates that both access points A and B present one door with access to either sides or double sided turnstile or two access points logically emulate double door This parameter influences antipassback function antipassback is activated in case of double sided door only and procedure of door state change states of blocking fire or alarm arise on double door synchronously Output usage group allows configuring of used output type operation modes and time of engagement Output usage determines way of outputs activation by control panel Lock output is activated at door open Alar
5. Gaeeaeuaetiass 17 Installation guide preface This document covers matter of adjustment of Intellect system that gives opportunity of utilizing of access control panels together with other hardware and software solutions used in the system Reader is supposed to already intoduced with installation and user manuals of adjusted control panels installation and user manuals are supplied RS 232 interface serial port 1s used for connection of Golden Gate access control systems to computer Hardware support is provided for the following access control panels of Integrated Technical Vision manufacture DLK642 F18 n F16 hereinafter DLK control panels To use RS 485 interfacing with control panels it is necessary to provide a NTC LNET interface converter with built in reader specially programmed for joint operation with Intellect system By means of NTC LNET signal strength of RS 232 and RS 485 buses are interchanged One output of converter is connected directly to PC COM port the other is connected to bus of control panels Before creating DLK control panels branch it is necessary to register GGPMngr exe COM server the registration is produced during Intellect system installation Do it manually using GGPMher exe regserver command Common structure of DLK modules integration Structure of objects interconnection for uploading of DLK control panels and interaction with objects of
6. Please describe in details bug matter and conditions If program generates message record it word for word
7. approach in providing cards codes with uniqueness unique 5 byte cards may prove to be identical within 3 bytes Parameter of Cards codes bits inversion is represented for the purpose of compatibility with control panels of other vendors Mark this parameter when using control panel with connection circuitry of reader signal line inverse to the circuitry adopted by Integrated Technical Vision company In this connection bits of cards codes received from control panels will be inverted by software when transmitted to Intellect In addition in DLK ACS settings window there are widgets typical for ACS represented in Intellect system Update Configuration button realizes uploading of all control panels filial to corresponding DLK ACS Synchronize time button accomplishes synchronization of time according to PC reference clock for these control panels Adding and adjusting DLK controller To add new control panel choose necessary point of Golden Gate ACS pop up menu see Fig 5 This object is associated with particular control panel on RS 485 bus Fig 5 Adding DLK controller In Address line of control panel settings see Fig 6 specify ID of control panel It is set on the control panel physically via jumpers for example in F16 F18 control panels or programmed from the keypad for example DLK642 control panel refer to control panel manual for detailed instruct
8. for controller DLK object Synchronize time synchronize time according to PC reference clock for this control panel Upload controller transmit configuration for this control panel Reset to fabric settings default settings are specified for control panel For details on default settings refer to control panel manual Door DLK object represents real location of door with which this object is associated Door icon reflects door state open closed or norm attention The following commands are available for door DLK object Open door commands to control panel to grant access through the door Door lock will be open To NORM BLOCKED FREE PASS mode changes door state correspondingly to command Indication of map objects state State of some objects is indicated directly on a map Notation conventions are presented below Some object states may be combined independently of one another for example states of control panel Tamper and 220V power loss Some states on the contrary exclude all other for example Connection loss ACS Golden Gate object No state Controller DLK object Stand by Controller DLK object Tamper alarm Controller DLK object Alarm The state arises when events of unconfigured door emerge or at break shortage of user zone parameter not available in Intellect system Controller DLK object 220V power low or absent Controller D
9. Contents TS CaO MOUS SLC LAC e us ctsscisscicec dn cseaisatisctica aneatssaina ses dansacwadlassuauaneventesunascadossaedaauareemawaantdets 2 Common structure of DLK modules integration ccccccccccccccecceeeeeeeeeeaeeeeeeeeseseeeeeeeeeeeeeeeeeeeeaaaaas 2 Uploads of COMMON PANG sissies etsssisccvsis enen e E ATE E A Eae 2 PO NIN a aE E E E O TOE 2 Users taD A A A A 2 Hardware taDseorepi an A AA A ec aeeea mane 3 Interaction with TCLS CLS y SCCM sg rrsnnerne in A EEE A 3 loteta cesta D a tae sheteate thea icteealatec ah lied tbateate ihiast adit aliae chi teudatabanegee haste tetostineuucte 4 Jai eye genealogy A a An tate eRen Seer tte Wc Meer nme eran eer Meee EETA open eaten ete ee eee 5 Creating and adjusting Golden Gate access Control SYStCM cccccccccsssssseseeseseeeeeececeeeeeeeeeeeaaaaas 6 Adding and adjusting DLK Controller ccccccssssssesssseeeeeeeceeeeeeeeeeeesaaeasseesesseeeeeeeeeeeeeeeeeeeeeaaaaaas 8 Adame and adi usin lt I LK CO Of enc A 10 Addine atid adjusting LNET Converter isis siieiciiechaseciiaadccaaetiodiaee ae 12 Usina MINTO DEKR ZAC S areara r na er nent tne E ny ern er ney A nee ear eee rer mer ee 13 lndicatomof MAD OD CCLS SUAS 2 cate cadets rated dastuetteteene niet ces eee baa tiation ENE 14 Tapie File MbAMOM TC ANU TES oaa Sonat Os oon on ease eases oka eee ee T 17 WY MGM any TINO COCS WONS sciecesoi act tani sccaesntienide Suteaneveidet iaayimceiuni teeoiee teases det ax waeeieeneeditn
10. Intellect system is optional for full system functionality Using map for DLK ACS Convenient way of monitoring is supervision of arising events directly on a map see Fig 13 For details on map creation and marking of map objects refer to corresponding chapter of this manual ACS Golden Gate object drawn on a map is used to set generic commands to all control panels on one bus Pop up menu of this object has the following operations available Synchronize time commands to all filial controllers to synchronize time according to PC reference clock This command must be started periodically to prevent real time clock deviation Typical deviation is 1 2 seconds per 24 hours For precise information on allowable rate of real time clock desynchronization refer to control panel manual Upload all controllers allows transmitting configuration for all filial control panels Controller DLK object presents real location of ACS hardware Exclamation marks may accompany controller icon Yellow exclamation mark signifies alarm state red exclamation mark loss of connection to control panel Control panel uploading is represented by bright green arrow Converterreader LHET 1 us Door DLE 1 ACS Golden Gate 1 Controller DLE 2 Tam per normal 26 01 05 1590239 Synchronize time Reset to fabric settings Upload controller Fig 13 Working with map The following commands are available
11. LK object Accumulator discharged or absent Controller DLK object Control panel is being uploaded configuration Controller DLK object Connection to control panel lost Door DLK object Door open Door DLK object Door closed Door DLK object Door is in Blocked mode access is granted only to security service parameter not available in Intellect system Door DLK object Door 1s in Free Pass mode or Fire Alarm mode Lock does not close Door DLK object Alarm The state arises at presentation of lost card door break alternative parameter of door settings at door open too long alternative parameter of door settings at card matching attempt alternative parameter of control panel settings Door DLK object Unknown state of door Connection to control panel is lost Converter LNET object Stand by mode Converter LNET object Connection to control panel is lost Implementation features l Time intervals with week cycle are NOT implemented since Intellect system still does not support this feature It is impossible to set several time zones for one door in access levels For example Access level 1 Door A always Door B never Avoid such clashes during configuration Operation of intellectual merge of time slots is NOT implemented For example Time zone 1 09 00 14 00 and 13 00 19 00 could be merged to save control panel memory Length of fa
12. assignment of simple system reactions on events Conditions of reaction launching are set by Events list all reactions indicated in Actions list are executed on meeting any specified condition Macrocommand object may be presented on a map and launched from it by hand Besides macrocommand may be launched from main menu of Intellect system where correspondent item emerges after macrocommant creation Program object implements assignment of more complicated system reactions on events Reaction handlers are written in script form and have advanced facilities as compared to macrocommand Each handler is designed as catcher function its name specifies its essence and parameters specify its additional conditions Body of such function specifies set of commands reactions on event For detailed information on creation and adjustment of standard access objects of Intellect system and setting of event handlers refer to the system manuals which 1s located in Help subfolder of Intellect system root folder file name is Intellect_eng chm in Windows Compiled HTML format Creating and adjusting Golden Gate access control system To create new object of Golden Gate access control system choose necessary computer in Hardware tab and in Create object floating menu choose ACS Golden Gate see Fig 3 ice fiona Pe i 5 Computer gam Settings oo o o oOo
13. ates that this input is connected to door contact sensor and events received from this input will be treated correspondingly In case of double sided door sensor may be common for both door A and door B Request to exit indicates that input is used as request to exit button for corresponding door Blocking for door indicates that the input is connected to door blocking button If contact is used as common for both door A and door B both doors are blocked at blocking button pressing Accumulator and Power 220V indicate that input is used for control of accumulator unit state or power state correspondingly When state of inputs is changed control panel produces corresponding message Good Lost Door contact and RTE button enables use of combined sensor For detailed information refer to control panel manual Adding and adjusting DLK door To add a door subordinate to available DLK control panel choose corresponding item of DLR controller pop up menu see Fig 8 This object is associated with one of two readers available in control panel hardware Hardware T a Gate 1 1 fi Controller DLK 1 RE B m en wy 4 faa 7 ii SEN i l 88 Controller DLK 1 EET TEE e sas ai M oeae Card matching attempts Eoo l Wait for PIN code sec fis 4 Delete object Controller DLK EEE I Double door es Create folder Output
14. cility code should be the same for all users Additionally you have to specify this length in compatibility settings of parent ACS Golden Gate Maximal card code depends on type of reader used It makes up 10 hexadecimal digits lower case for Wiegand42 and 6 hexadecimal digits for Wiegand26 In decimal system of codes recording maximal code is 256 1 for Wiegand42 and 256 1 for Wiegand26 When facility code is used bits are borrowed from card code and maximal code decreases correspondingly Maximal length of PIN code makes up six decimal digits Code itself may be shorter Some values are limited in quantity usually up to 255 which is due to hardware constraints If limited number is exceeded configuration cannot be uploaded to control panel Quantity of cards is limited by control panel EEPROM memory Maximal number of cards for DLK642 control panel is 1024 for F16 and F18 4096 When anything goes wrong l 2 3 Read this manual once again Verify accuracy of control panel connection presence of power and grounding When new configuration is uploaded to control panel the panel requires some time about 3 seconds after message Operation in new mode to recalculate schedule Control panel may incorrectly react to card passed during this period If the above advices do not help consult to developer We will be glad to receive any help in module debugging on support itvsystems com ua
15. ions 6 4 Computer k E ACS ewe oa oe 1 ae Door contact tor door A MS Request to exit for door A Door contact for door B pg Request to exit for door B Free pass for doors A and B Mey Power 220 Blocking for doors A and B iz NFB Accumulator Fig 6 Adjusting DLK controller NOTE Hardware based ID of all control panels is set to O value at sale If there are more than one control panel on RS 485 bus impact of addresses emerges and system will NOT work correctly Prior to connection it is necessary to provide unique hardware based address of each control panel within one bus these will be all control panels of one Golden Gate ACS in Intellect system NOTE If address is not set properly it is set to 0 by default when creating control panel the control panel will not be found There emerges Impossible to find control panel event in events report window It is recommended to choose number in a list automatically generated during search of available control panels To activate search process press Search button to the right of address field Search process is displayed by corresponding message box see Fig 7 All found control panels are added to drop down list of control panels address Wa T z Card matching attempts is a peak VESE AN amount of unknown cards presented CITT to reader without alarm activation If 00 01 02 03 04 05 06 07 08
16. ive complete list of events and reactions supported by an object use Tools ddi exe utility which is supplied with Intellect system Load it by means of eng ddi file from system root folder and refer to Events and Reactions tabs in properties of interesting object Interfaces tab Here Screens or user interfaces are adjusted Create new screen and associate it with computer where the screen will be available After that it is possible to create interface windows as screen child objects NOTE Dimensions and position data of windows is specified in PERCENTS of screen dimensions not in pixels that is why values exceeding one hundred have no sense Map interface serves for visual presentation of guarded territory topology and displaying of objects events in graphical form Icons for hardware objects may be reflected on a map after creation of rooms image When events arise hardware icons may change signaling about events Object reactions are available in its context menu and operator may immediately react to events Event log interface reflects events in table form indicating complete information about events that is source time event name and additional parameters in chronological way This interface has no feedback mechanism with operator Programming tab Here it is possible to create software based event handlers which do not require operator interference Macrocommand object serves for
17. m output at alarm activation Horn output at alarm activation except for tamper violation Mode controls hardware operating mode of output Available types of modes are Start stop Impulse and Triggered Start stop mode is set for electromechanical locks of latch type and electromechanical locks In that mode lock changes its state at energizing and deenergizing for example it is closed at being energized and open at deenergizing Impulse mode is applied to electromechanical locks or bells lock is opened or bell activated by voltage impulse Triggered mode is used for specific locks that have two different signals for mode change for example Arm system and Disarm system which alternate each other For detailed information on necessary mode type turn to user manual of device connected Time value is used only for impulse mode of output It specifies length of impulse for door opening in seconds When time is set to 0 control panel will produce short impulse about 200msec NOTE time should not be too long since lock may be overheated by energy consumption at very long impulse supplied It is recommended to use minimal time value enough for lock engagement Input usage specifies information that is transmitted to control panel and defines response to event emerged Not specified input designates to control panel to ignore input events Door contact indic
18. ocked refer to documentation for detailed info LNET settings that is Inquire reader see Fig 12 When Inquiry reader Fig 11 Warning message in case of specially programmed LNET box is marked reader of converter absence converter 1S periodically inquired about presence of passed card In case of card presence corresponding message is generated in Intellect system When Inquiry reader box is not marked only reader will process passed cards corresponding messages will not be generated and cards will be ignored S Computer Kv J Fe A Cr fc ter reader LNET 1 aa ACS Golden Gate 1 1 I ec dii zl 8 Controller DLK 1 1 ACS Golden Gate 7 Disable ACS Golden Gate 1 Bk Door DLE 1 1 1 Hp Door DLK 2 1 2 Converter reader LNET 1 i Fig 12 Adjusting LNET converter NOTE presence of LNET converter specially programmed for operation with Intellect system is obligatory for providing of full functionality of software In case that LNET converter is not programmed for operation with Intellect system software operates in DEMO mode see Fig 11 Basic functionality of modules namely uploading of control panels and messages generating will be blocked for corresponding COM port Connect LNET device supplied for joint operation with Intellect system to EACH used port and restart the system Presence of LNET converter object in hardware list of
19. r parameter indicates quiet door behaviour masking less informative access events When Mask door sensor field is marked Door opened too long message is not transmitted to event log NOTE It is recommended to mark this parameter in case of nonrigourous access policy on inside doors of supervised objects Adding and adjusting LNET converter To add LNET converter object subordinate to Golden Gate ACS choose corresponding item of ACS Golden Gate pop up menu see Fig 10 It is associated with converter reader LNET by means of which RS 485 bus is connected to PC communication port Hardware pA a Computer kv r aes BaF ACS Go E 1 Now ras a a acs Golden Gate 1 ea eh VideoServer gt Disable Computer Upload configuration eigen Synchronize time l Hexadecimal na Converter reader LNET has several functions First it functions as converter of RS 485 RS 232 which allows to manage control panels from computer Second it has built in reader that helps to automate cards enrollment on operator workplace since reader is situated in immediate vicinity to PC Last it functions as hardware serial key protecting integration modules from being copied Error in modue DLK run There 1S only one Convertor LNET not found for port COM1 object s ID 1 which acts as a hardware serial key The most of parameter possible in controler facilities will be bl
20. r permanent or temporary card otherwise user adjustment will be senseless Hardware tab Integration modules introduce several specific new objects in objects list Creation and adjustment of integration modules 1s described in detail in the following chapters Interaction with Intellect system Interaction of introduced DLK objects with standard Intellect system handlers see Fig 2 is implemented on the basis of two mechanisms that is object events and object reactions Intenaces s Programming Fig 2 Common structure of DLK modules integration Intercaction When significant access event arises corresponding object generates event that informs about this event the core of Intellect system and all other event handlers through the core For example when door sensor is broken door associated with the sensor generates Door open event If necessary some parameters are specified in event message for example when card is passed to reader DLK door object associated with the reader may generate event message Access granted object code XXX card code XXXXXXX In case of necessity of feedback with hardware event handler activates reaction for corresponding hardware object For example when operator gives command to open door Open door reaction activates for corresponding door object at command to upload control panel Upload control panel reaction is activated To rece
21. rol panel will not be able to associate event emerged for the other door type with any door available Message Control panel is not configured unknown door event will be generated If more than one door of same type is connected to control panel the control panel will refuse to download settings since door settings are replicated Access time parameter indicates maximal time for door being open without arising alarm state When access time is exceeded reader switches to alarm state and message Door open too long emerges NOTE this time should be long enough for any user with access rights to have time to pass through access points within time limits Refer also to Disable alarm on door open too long point Disable alarm on door force to open parameter prevents switching of control panel to alarm state at unauthorized door sensor break NOTE it is NOT recommended to mark this parameter without extreme necessity Marking of this parameter disables control of real door break event It may be marked temporarily in case of door sensor breakage or in case of closed door travel until trouble shooting Disable alarm on door opened too long parameter prevents switching of control panel to alarm state on access time expiry At the same time Door opened too long message is generated NOTE it is recommended to mark this parameter only in case of nonrigourous access policy on inside doors of supervised objects Mask door senso
22. s usage 1 Move to folder Ne Usage Lock for door A Mode Start stop v Time sec a On map 7 Nz Usage C for door B zi Mode Start stop v Time sec MeS Usage Hom x Mode mpulse v Time sec fo Find Ne4 Usage Alarm hd Mode Start stop v Time sec o Inputs usage Ne Door contact for dora N5 Request to exit for door 4 x NE2 Door contact for door B 7 NS Request to exit for dorg 8 NS Free pass for dorsa ande ooo li NN Power ossaa Ned Blocking for doorsA andB NSB fAccumulator tsi Fig 8 Adding DLK door Create two subordinate door objects as filial to control panel see Fig 9 Specify type A for one door and type B for the other By that correspondence is set up between adjustable door object outputs and inputs which are specified during control panel adjustment Create one door if one access point is unused Control panels controlled by modules have in their hardware and intrinsic software the constant number of supervised access points that is two They are marked correspondingly A and B When operating Intellect system user may abstract himself from this fact since it 1s masked in intrinsic implementation To control bigger amount of doors use appropriate number of control panels Se Computer k S a ACS Golden Gate 1 1 6 Controller DLK 1 1 A Door DLE 1 1 1 E Ri Door DLK 2 1 2 NOTE If only one type of door is added cont
23. supposed to use Wiegand 26 interface do not forget to indicate it when ordering readers Scale of notation determines in Users Settings of Intellect software in which system codes of cards are specified either decimal or hexadecimal This parameter is provided for purpose of compatibility with existing databases and facilitation of manual codes entering in cases when codes are marked on cards Facility code length specifies quantity of bytes destined for Facility code field in users settings of Intellect system This code borrows bytes of full card code accordingly shortening its length Card code length is calculated as complete code length with subtracted facility code Allowable range is from 0 up to complete code length 1 Complete code length is 3 bytes for Wiegand26 and 5 bytes for Wiegand42 If facility code length is 0 then any specified facility code is ignored Arenlectu Fa ee SES p a pass Lae 29 ACS Golden Gato 1 1 Fr acs Golden Gate lire S F Disable j 2 l A EEE ee E irar f T a ey 5 ae Hexadecimal Fig 4 Adjusting Golden Gate access control system NOTE All users cards must have common format equal facility code length and card code length common scale of notation Use of miscellaneous scales for example simultaneous use of 3 byte and 5 byte readers is complicated by fundamentally different content of necessary data and different

Intellect

Contents

Download Pdf Manuals

Related Search

Related Contents