manual_spp-r400_user_english_rev_1_02 (USA)
Contents
1. 4 The switch is the disconnecting device Turn off switch from any hazard 5 The following Bluetooth mark and QD ID B019948 is only applicable to models with the Bluetooth SIG qualification C3 Bluetooth Warning Lithium lon Battery pack Warning The battery has the potential risk of overheating fire and or explosion To avoid such risks observe the following instructions A visibly swollen battery may be dangerous Contact BIXOLON or your local dealer Only use an eligible charger Keep away from open flames Do not place in a microwave Do not leave the battery pack inside a vehicle in summertime Do not store or use in a hot and humid place like a sauna with sleeping rooms Do not place the battery pack on a quilt an electric blanket or a carpet for a long time Do not store the battery pack switched on in an enclosed place for a long time Do not allow the battery port to touch metal items such as necklace coin key or clock etc Use the lithium secondary cell guaranteed by mobile phone manufacturer or BIXOLON Do not disassemble compress or pierce the battery pack Do not drop the battery pack from a high place or subject it to strong shock Do not expose the battery to high temperatures over 60 C Do not expose to humidity Rev 1 02 29 SPP R400 Disposal Directions Do not dispose of waste battery packs recklessly Do not burn or throw in fire to dispose of the bat2. Af Battery Pack Single Battery Vehicle Charger Cradle Charger Interface Cable Cleaning Pen Rev 1 02 10 SPP R400 2 Product Part Names Front Paper Cover Power Button Open Button MSR Cover Power Button Rear Shoulder Strap Belt Strap Hole Connection Holes Interface Cap Vehicle Cradle Connection Connection Power Connection Rev 1 02 11 SPP R400 3 Installation amp Usage 3 1 Battery Installation 1 Insert the battery on the rear side of the printer aligning the battery hook properly 2 Push the battery into the slot until a snapping sound is heard NOTE As the battery is not charged at the time of purchase charge the battery before use 3 2 Battery Charging 3 2 1 Using Battery Charger F 1 Turn off the printer power 2 Connect the power cord 2 to the battery charger D and then connect AC power 3 Open the external interface cap in the direction of 3 4 Connect the battery charger to the power connector CAUTION The printer may be seriously damaged if a battery charger not provided by BIXOLON is used BIXOLON is not liable for such damage WARNING Turn off the power before charging the battery for the printer Rev 1 02 12 SPP R400 3 2 2 Using Single Battery Cradle Optional 1 Connect the power cord 2 to the battery charger 2 Connect the battery charger to the power connector of the single battery cra
3. Risk of explosion if Battery is replaced by an incorrect type Dispose of used Batteries according to the instructions 1 Do not use or leave the battery in a location exposed to high temperatures or intense direct sunlight such as within an automobile Doing so can cause battery overheating and or combustion n addition battery performance and product life may be reduced The battery contains a safety mechanism to prevent danger not use the battery in a location that is prone to static electricity above the amount covered by the manufacturers product warranty that can cause damage to this safety mechanism Damage to the safety mechanism can result in battery overheating combustion and or explosion The temperature ranges for battery usage are as follows Any usage outside of these ranges can result in battery overheating and or damage In addition battery performance and product life may be reduced Charging 0 40 Product Usage 20 60 C Storage 20 60 30 days Long Term Storage 20 40 C 90 days Please review the exclusive charger manual carefully for charging instructions If you observe any abnormal symptom such as strange smell and overheating on first use after purchasing the product contact your local dealer immediately If a child must use the battery the child s parent or legal guardian should clearly explain the instructions from the user manual prior to use In
4. the product is required use the exclusive charger to charge the battery 3 To avoid improper use of the battery review the product user manual carefully 4 Do not charge the battery for long times in excess of the normal charging time indicated in the user manual 5 If the battery is not to be used for a long period of time remove it from the product and store in a location with low humidity If the battery is stored while still inserted in the product in a highly humid location oxidization may occur along with a decline in battery performance 6 After product usage make sure to turn power off Neglecting to do so can cause a decline in battery performance 7 A battery that has not been used over a long period of time may not be sufficiently charged Even if the battery is not to be used charge the battery to the status recommended by the manufacturer once every six months Neglecting to do can cause a decline in battery performance and product life 8 If the battery terminal is dirty use a dry cloth to wipe clean prior to use Neglecting to do so can result in poor connection with the product causing power stoppages or failed charging 9 Each battery has a life cycle If the usage time of the produce is shortened replace with a new battery Insulate the used battery by attaching insulation tape to its port and then dispose of the battery according to local regulations Other Precautions The copyright for this user m
5. addition the parent or legal guardian should periodically confirm that usage is being conducted in accordance with user manual instruction during use Store the battery in a location that is out of the reach of small children During usage make sure to also place the charger and or product out of the reach of small children If the battery is leaking electrolytic solution and the solution comes in contact with the skin or clothing immediately wash thoroughly with clean water Contact with skin can result in skin disorders Make sure to review the user manual and precautions carefully prior to use In addition after carefully reviewing the user manual and precautions place them in a secure location for future reference when needed 10 There is a risk of explosion when replacing with an incorrect battery Only exchange it for another one of the same or equivalent model specified by BIXOLON Insulate the used battery by attaching insulation tape to its port and then dispose of the battery according to local regulations 11 If using the printed side of preprinted paper this may cause malfunction Rev 1 02 8 SPP R400 amp Recommended 1 Review the user manual for instructions concerning insertion removal of batteries into from the product 2 As the battery is slightly charged upon factory shipment use it to confirm proper product operation upon purchase If product operation cannot be confirmed or longer use of
6. of product performance are explained 4 Bluetooth amp Wireless Manual Bluetooth This manual describes how to connect terminals PDAs PCs etc with Bluetooth functionality Wireless LAN This manual describes how to connect wireless LAN in infrastructure or ad hoc mode 5 Commands Manual This manual provides information on the protocol and functions of the control commands that can be used with this product 6 Code Pages Manual This manual provides information on each character code page that can be used with this product We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality of all our products n following product specifications and or user manual content may be changed without prior notice Rev 1 02 3 Safety Precautions SPP R400 In using the present appliance please keep the following safety regulations in order to prevent any hazard or material damage WARNING Violating following instructions can cause serious injury or death Do not plug several products in one multi outlet This can provoke over heating and a fire f the plug is wet or dirty dry or wipe it before usage f the plug does not fit perfectly with the outlet do not plug in Be sure to use only standardized multi outlets Do not pull the cable to unplug This can damage the cable which is the origin of a fire or a breakdown of the printer PROHIBIT Do not plug in or un
7. or strike with a heavy object such as a hammer and take care not to step on the battery There is a potential risk of battery overheating combustion and or explosion caused by an internal short circuit Do not solder the battery directly Doing so may melt the insulating materials and or damage the safety mechanism or safety equipment resulting in battery overheating combustion and or explosion Do not disassemble and or modify the battery The battery contains safety equipment and a safety mechanism to prevent danger There is a potential risk of overheating combustion and or explosion caused by disassembly Do not charge the battery near open flames and or under direct sunlight Because exposure to high temperatures triggers the operation of the safety mechanism the battery may not charge or may overcharge due to destruction of the safety mechanism There is a potential risk of overheating combustion and or explosion Do not expose the battery to high temperatures over 60 C and do not use or store it in a hot or humid place Warning 1 Do not place the battery within the reach of small children to prevent any swallowing accidents f a small child has swallowed the battery consult a physician immediately Do not place the battery in a microwave oven or a high pressure unit Doing so may cause sudden overheating of the battery and or the destruction of its seal resulting in battery overheating combustion and or
8. receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device is not intended for use in the direct field of view at visual display workplace To avoid incommoding reflexions at visual display workplaces this device must not be placed in the direct field of view 8 3 Label Types The labels used on this product are composed of the following materials BIXOLON logo label PC Rating Label PP Other labels PET Rev 1 02 30
9. BIXOLON User s Manual SPP R400 Mobile Printer Rev 1 02 http www bixolon com SPP R400 Table of Contents Manual Information amp Usage Precautions emnes 3 1 Content Confirmation ee eee eee eee eee eee eee H II I HII IH IH 10 2 Prod ct Part Names RI EiRi SaR 11 3 Installation amp Usage Wes ere en wv ee dace OE Gao c o e ree a RD a ce c a rw M 12 3 1 Battery Installation ESTATE E RERO TRICE Re CR CS ROTE LIO 12 3 2 Charging manasasasanuasaauasaasanmasanmasansasaasaAsnuananuanusanauassauaauananananasasananananuaaaa 12 3 2 1 Using Battery Charger SPER CRIT MR REE RTE CCE 12 3 2 2 Using Single Battery Cradle Optional mH 13 3 2 3 Using Vehicle Charger Optional CERNE III DA SD 13 3 2 4 Using Quad Battery Charger Optional ERC ERIC RO TRICE R CR ATEEN 14 3 3 Paper Installation REIN CEN ET PERC ERE TOI CICS CIO COCO ROR RIOT 16 3 4 Using Belt Strap TIO LDAP ILO DIL CELO ODDO I 17 3 5 Using Case Protective Case Optional RO Rei a avai IR Br ua M rn Tu 18 3 6 Using Shoulder Strap Optional ES 19 3 7 Adjusting P
10. J 0123456789 lt gt JKLMNOPQR 0123456789 lt gt ABCDEFGH JKLMNOPQRS 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ 0123456789 0ABCDEFGH JKLMNOPQRSTUVWXYZ 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXY Z W 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZI W 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXY Z W 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W 123456789 20ABCDEFGH JALMNOPQRSTUVWXYZ W r MNOP QRSTUVHXYZT WJ 3456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZI W _ 456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W _ 56789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W _ a 6789 lt gt ABCDEFGH JKLMNOPQRSTUVWWXYZ W _ abcde 789 lt gt JKLMNOPQRSTUVWXYZ W abcdef 89 0ABCDEFGH JKLMNOPQRSTUVWXYZ W abcdefg 9 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W abcdef gh 0ABCDEFGH JKLMNOPQRSTUVWXYZ W abcdefgh AMNDODOVSCZ PC437 amp Pty amp c eitiAA eE6600ujD c Y Ptfa aaaac sitiAAExeAosonupucey Ptf E66000j3D c Y 0 Pt tf i Neo Ptf l n eitiAA c E6600 j
11. Printer Battery 697g 1 54165 Weight Einer Printer 4 Battery Paper 939g 2 07165 Shipping Package Approximately 1530g 3 37165 Basic Package Battery Pack Battery charger Belt strap Paper Shoulder Strap Case Protective Case Battery Pack Accessories Sold Separately Single Battery Cradle Quad Battery Charger Vehicle Charger Interface Cable Cleaning Pen Rev 1 02 28 SPP R400 8 2 Certification 1 WEEE Waste Electrical and Electric Equipment This mark shown on the product or its literature indicates that the X corresponding item should not be discarded at the end of its working life with other household waste To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate marked items from other types of waste and recycle them responsibly to promote the sustained reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can conduct environmentally safe recycling of such items Commercial users should contact their suppliers and check the terms and conditions of purchase contracts This product should not be combined with other commercial waste for disposal 2 Rating Label Symbol Information mu EN DC Direct current 3 This equipment is indooruse and all the communication hiring are limited to inside of the building
12. anasasaualaauaanananananasananansasunaana 28 8 2 Certification anassaassaAasaiaszsainanuansanansanansanHansanansanansu auauuuauaaaunuasanasanananasunasuuasauauauunuans 29 8 3 Label Types amasasassaasaaaskaanuaazauanansanmananmauaHansuHaasuuauuauanasanasanasanananasunuasunuanan 30 Rev 1 02 2 SPP R400 B Manual Information This user s manual contains basic information for product usage as well as for emergency measures that may be required The following separate manuals provide more detailed content on various technological issues and areas 1 Windows CE Module Program Manual This manual provides information on the dll files required for Windows CE application program development 2 Windows Driver Manual This manual provides information on installation and main functions of the Windows Driver for this product 3 Unified Utility Manual This manual provides information on the software used to select functions of this product modify operation conditions etc VMSM Virtual Memory Switch Manager As a function that sets the basic operation conditions of the product the use of non hardware control software based virtual switches is explained NV Image Download Manager The downloading of image files such as logos intended for repetitive printing is explained Firmware Download Manager The downloading and installation of the latest Firmware which is subject to ongoing modification for the enhancement
13. anual and various other manuals is property of the BIXOLON Co Ltd Any copying or conversion into electronic firm and saving of this material without the express written permission of BIXOLON Co Ltd is strictly prohibited Use of the information contained in this manual is not subject to any patent liability This manual has been prepared with utmost care and attention to detail but may contain certain errors and or omissions BIXOLON Co Ltd is not legally liable for any damages resulting from the use of the information in this manual BIXOLON Co Ltd and its affiliates are not legally liable United States excluded for any damages loss costs and or expenses that result from the breakdown malfunction and or misuse of the product due to violation or neglect of the operation and maintenance information and instructions provided by the BIXOLON Co Ltd as well as from the unauthorized alteration repair and or modification of the product by the user and or third party BIXOLON Ltd is not legally liable for any damages and or issues resulting from the use of options and or parts that are not authentic BIXOLON products or authorized products Rev 1 02 9 SPP R400 1 Content Confirmation The following items should all be contained in the printer package Contact the dealer from which the purchase was made if any item is damaged and or missing Basic items SPP R400 amp Paper Optional items
14. aper Guide RR Rr RM RR E RR Grace 20 3 8 Using Control Panel TCR RE T ADOS IOCIS RTA RICCI E ICI E Oe TOC COD QC 21 3 9 Using MSR 22 A NEST ULL DE C CI IU I eee 22 5 Label Printing F nctlOD ene Sk ee eal ee ee AIC 25 5 1 Label Function Setting EDT RI E ER RII ER OORT OR RIPEN 25 5 2 Auto Calibration Function TOP 25 6 GonnectliOn ree ERI E 26 6 1 Bluetooth amp Wireless LAN Connection ERR RCE CIR 26 6 2 Interface Cable Connection ROTER SERERE TOOL TE IOS IDOL aaa E CREE D 26 T Printer Cleaning I E CP ME RESET 27 8 Appendix wate eine ERE SQ DER DE NIE FEE NES 28 8 1 Specifications anassnsasasasaasadnuasanmasanasusasupuaAssana nananm
15. ause a fire or an electrocution Switch off and unplug the printer before calling your dealer TO UNPLUG SPP R400 lll Battery Safety Precautions Make sure to review the user manual carefully prior to product use Neglecting to heed the following instructions can result in battery overheating combustion explosion damage and or decline in performance and product life Danger 1 Do not allow water seawater or moisture to enter or leak into the battery If the safety mechanism within the battery becomes oxidized the battery may overcharge with abnormal electrical current and or voltage so that it may overheat ignite and or explode Do not place the battery near open flames or heating devices such as stoves Exposure to excessive heat may cause damage to the resin case and or insulating materials thus causing a short circuit within the battery that may result in battery overheating combustion and or explosion Charge the battery only with the exclusive charger specified optionally provided by BIXOLON The use of an incorrect charger may result in overheating combustion and or explosion of the battery Charging the battery with a modified charger may result in overheating combustion and or explosion of the battery by abnormal chemical reaction caused by incorrect polarity Do not directly connect the battery to an electrical power outlet not specified by BIXOLON or an automobile s cigarette lighter jack D
16. dle 3 3 Plug the power cord 2 into an electrical outlet 4 Insert the battery 4 into the battery holder 3 until a snapping sound is heard 1 Turn off the power to the printer 2 Connect the vehicle charger to your car s cigarette lighter jack 3 Open the external interface protection cap in the direction of 2 4 Connect the vehicle charger to the power connector amp CAUTION The printer may be seriously damaged if a battery charger not provided by BIXOLON is used BIXOLON is not liable for such damage WARNING Turn off the power before charging the battery for the printer Rev 1 02 13 SPP R400 3 2 4 Using Quad Battery Charger Optional 3 2 4 1 Connecting the cables 1 Connect the power cord to the adaptor and Connect the adaptor to the power connector of the quad battery charger 2 Plug the power cord into a power Outlet Input power is 100 240VAC 50 60Hz 1 0A 3 When the power is supplied the yellow green and red lamps are on for three seconds and do the self test Pa P 47 A PA 4 WARNING Use only designated AC DC adaptor 12VDC 3A Rev 1 02 14 SPP R400 3 2 4 2 Battery Charging 1 Insert the battery into the quad battery charger as shown in the figure on the left 2 Gently slide the battery until it reaches the bottom of the charger 3 Charging starts as soon as the battery is completely inserted 4 After charging remove the batte
17. ensor Front side of paper MSR data including sentinel Character mode None MSR read mode Auto TRACK1 2 3 Memory switch setup status Memory S W1 NE Memory S W3 12345678 ON OFF EENE Memory S W5 12345678 ON OFF EENE Memory S W7 1234 RF Interface Not available bluetooth WLAN firmware version Ver 0 1 WLAN MAC address C7A00010877 Name SPP R400 Network Mode Adhoc Encryption None ESSID BIXOLON adhoc DHCP Disabled IP 192 168 1 1 Netmask 255 255 255 0 Gateway 192 168 1 2 Port 9100 HTTPS Disabled Telnet Disabled FTP Disabled SNMP Disabled Memory S W2 12345678 ON Memory 5 4 12345678 ON Memory S W6 12345678 op ui orm Memory S W8 12345678 ON OFFERRE RR WN SS you want to continue LF TEST printing FEED button ASCII 18958 0123456789 0A 8 0123456789 0AB 8958 0123456789 lt gt ABC 0123456789 0ABCD 8 0123456789 0ABCDE BCDEFGH JKLMNOP C D E amp 0123456789 0ABCDEFG H jJ K C DEFGHI JK EFGHIJKL F G H U GHI JKLM HI JKLMN JKLMNO JKLMNOP KLMNOPQ 0123456789 lt gt ABCDEFG 0123456789 0ABCDEFGHI
18. explosion Do not use the battery with primary batteries like dry cells or other batteries of different capacity or type Doing so may cause excessive discharge in use or excessive charge when charging it resulting in an abnormal chemical reaction within the battery that can cause battery overheating combustion and or explosion There is a potential risk of overheating combustion and or explosion due to adverse chemical reaction in the battery If the battery starts to emit strange smells or if you find unusual symptoms such as overheating discoloration and deformation remove the battery from the product or the charger and discontinue use of the battery The use of the battery in abnormal status may result in battery overheating combustion and or explosion If the battery is not charged during a certain time when trying to recharge discontinue charging There is a potential risk of overheating combustion and or explosion If battery leaks its electrolyte or gives off a strange smell keep the battery away from open flames immediately The leaked electrolyte may catch fire There is a potential risk of overheating combustion and or explosion If the battery is leaking electrolytic solution and any of the solution enters the eyes immediately wash out with clean water and then consult a physician to receive treatment Neglecting to do so can cause permanent eye injuries Rev 1 02 es SPP R400 Caution
19. face Baud rate 115200 bps Data bits 8 bits Parity None Stop bit 1 bit or more Handshaking DTR DSR Default Codepage PC437 Print Speed 80mm s Double byte character mode Off Font 12x 24 Paper out Bell Off Low Battery Buzzer On Power off time 15 Min Idle mode time 10 Sec Black Mark sensor Front side of paper MSR data including sentinel Character mode None MSR read mode Auto TRACK1 2 3 Memory switch setup status Memory S W1 12345678 ON ON OFF NN NN OCHEEENEENE Memory S W2 12345678 Memory S W3 Memory S W4 MEE i 12345678 ON OFF TT oad TILT Memory S W5 Memory S W6 ON Memory S W7 Memory S W8 12345678 12345678 ON Hil ON OFF RE Interface BT embedded Bluetooth firmware version 4 0 0 Bluetooth BD address 74F07DB00162 Auth amp Encry are enable Connection Mode 2 Not available WLAN Rev 1 02 SPP R400 SS SS SS NS If you want to continue SELF TEST printing please press FEED button ASCII 1 8 amp 0123456789 lt gt ABCDEFGH JKLMNOP amp 0123456789 lt gt ABCDEFGH JKLMNOPQ 8 0123456789 lt gt ABCDEFGH JKLMNOPQR amp 0123456789 lt gt ABCDEFGH JKLMNOPQRS amp 0123456789 0ABCDEFGHI JKLMNOPQRST amp 0123456789 lt gt ABCDEFGH JKLMNOPQRSTU 0123456789 lt g
20. interval being 10 seconds Rev 1 02 21 SPP R400 3 9 Using MSR 1 Press the MSR cover to open 2 Insert the card as shown in the image and swipe in the direction of the arrow can be done in both directions 3 When finished using press the MSR cover to close it NOTE If the card does not register first check to see if itis properly aligned When swiping the card the recommended swiping speed is 100 1200 mm sec 4 Self Test Run the self test when first setting the printer or when encountering a problem and check the following Control Circuit Mechanisms Print Quality ROM Version and Memory Switch Settings If no issue is found with the printer after running the self test examine the other devices or peripherals and software This function is independent of such other devices and software Self Test Instructions 1 Turn the printer power off and close the printer paper cover 2 Pressing the paper feed button and power button simultaneously turns the printer on 3 The printout is produced after releasing the two buttons 4 To add a printout of the ASCII pattern press the paper feed button once more 5 After the ASCII pattern is printed out the self test is automatically terminated Rev 1 02 22 Self Test Sample For Bluetooth Firmware version V01 00 STOB 050812 Butter Capacity 128K Bytes Print Density 10096 Bluetooth Interface Baud rate 115200 bps Serial Inter
21. oing so may result in overheating combustion and or explosion of the battery by over current and or over voltage Do not heat the battery or place it near a fire Doing so may melt insulation materials damage the safety mechanism equipment and or ignite the electrolytic solution There is a potential risk of battery overheating combustion and or explosion Do not reverse the connection of and electrodes of the battery Charging the battery in reverse polarity may produce an undesired chemical reaction inside the battery cell causing unexpected behavior during discharging such as overheating explosion or fire Do not allow the battery s or pole to come into contact with any metal In addition do not carry or store the battery with metallic items such as necklaces and hairpins Doing so may cause a short circuit of the battery generating an over current There is the potential risk to overheat ignite and or explode the battery or overheat the metallic items such as necklaces hair pins etc Do not throw the battery or subject it to strong shock If the safety mechanism in the battery is damaged the battery may be overcharged and consequently an adverse chemical reaction may be generated in the battery There is a potential risk of battery overheating combustion and or explosion Rev 1 02 6 10 11 12 13 14 SPP R400 Do not pierce the battery with a pointed object such as nail or awl
22. osoaupuce Ptfafoun ce 0 PtfaioufiN c eitiA AEa E 60600 jD Uc Y Prf l nNe eitiA E ao E6600 jD c Y Ptf i nNe e eitiA c E600 jD c Y Pt if unN u 1 0 5 4 amp PtfaiounN g 1 amp 1 A s E 000 jD c Y PtfaiounNe g s E660005p 0c Y PLf l nN z A Vic s E66000 c Y PtfaiounNe g e E660 0 jD c Y 4 E66000jDU ce PtfaiouhNeg p 4 6000 c Y PIf i unN z 4 SoGUPUCEY Plf l RN z p ie oaupUcey p 4 Ai 4 dUPUCEY 1 amp r 4 727416 4 AP p 4 27 4 POUCEY PtfaiduAN r4 ajo 7 Completed 23 Self Test Sample For Wireless LAN SPP R400 Firmware version V01 00 STOB 050812 128K Bytes Butter Capacity Print Density 10096 Bluetooth Interface Baud rate Serial Interface Baud rate Data bits 8 bits Parity None Stop bit Handshaking DTR DSR Default Codepage PC437 Print Speed 80mm s 1 bit or more 115200 bps 115200 bps Double byte character mode Off Font 12 x 24 Paper out Bell Off Low Battery Buzzer On Power off time 15 Min Idle mode time 10 Sec Black Mark s
23. p c Y Pif i un eod r A c E6600 jD c Y 1 i s E60000jp0c Y PtfaiouANn g Mia Ex EododupUceY PifaiounNe p ate e E6600 jp c Y Ptf N BEA 6600 0jp c Y PtfaiouhNee EA 600up ct Y PLPaiounineeg Completed Rev 1 02 24 SPP R400 5 Label Printing Function 5 1 Label Function Setting Label paper and black mark paper available at the label mode Setting Operations 1 Turn on the printer power 2 Open the paper cover and press and hold down the paper feed button for longer than two seconds 3 After the buzzer tone is emitted insert paper and close the cover 4 Repeat the steps above to return to receipt mode Setting Via Memory Switch Please refer to the memory switch changing section of the Commands Manual 5 2 Auto Calibration Function The label printing function requires the recognition of label paper gaps and black mark paper black bar in order to print If label paper gaps are not properly recognized use the auto calibration function Auto Calibration Instructions 1 Turn the printer power off while in label print mode 2 Press and hold down the paper feed button and then press the power button 3 After the following printout is outputted press the power button to perform auto calibration Select the mode Auto Calibration Power Button Self Test Feed Button 4 Three pages of label paper are outputted when perfo
24. phics Standard ENG 128 x 33 pages Character Set Others KOR CHN JPN 128 x 20 pages Printin International 32 9 1 Dimension UPC UPC E CODE 39 CODE 93 Barcode Code 128 EAN 8 EAN 13 ITF Codabar 2 Dimension PDF417 DATAMATRIX MAXI QR Code Emulation BXL POS Driver Windows XP WEPOS 2003 Server VISTA 2008 Server 7 8 SDK Windows XP WEPOS 2003 Server VISTA 2008 Server 7 8 Windows CE 5 0 and later Sensor Paper End Paper Cover Open Switch Front Rear Black Mark Cutter Type Tear Bar Language User language supported Paper Type Thermal paper Width 104 5 0 5 mm 4 11 0 2 Paper 111 5 0 5 mm 4 39 0 2 Diameter Max 257 mm 2 24 Thickness 0 07 0 003 mm 50 Reliability Battery Rechargeable up to 300 times Serial USB Bluetooth Class2 V2 0 EDR Wireless LAN Communica 802 11 6 9 tions Communication is enabled only for devices with Bluetooth or Wireless LAN function Input Voltage 100 250 VAC Battery Current 0 5A Max at 110VA Charger Voltage 8 4 VDC Current 0 8A Output The charging current and the charging time may vary depending on the type of charger option Cell Lithium ion Voltage 7 2 7 4 V Battery Charging Capacity 2600mAh Charging Time Within four hours Usage Temperature 15 50 C 5 122 F Conditions Humidity 10 8096 RH No condensation Dimensions Printer 147mm x171 4mm x 66 7mm 5 79 x 6 75 x 2 63 Printer 595g 1 31165
25. plug with your hands wet You can be electrocuted m tut S f You must use only the supplied adapter It is dangerous to use other adapters ONLY SUPPLIED ADAPTER PROHIBIT Keep the plastic bag out of children s reach If not a child may put the bag on his head PROHIBIT Do not bend the cable by force or leave it under any heavy object Adamaged cable can cause fire PROHIBIT Rev 1 02 4 CAUTION SPP R400 Violating following instructions can cause slight wound or damage the appliance If you observe a strange smoke odor or noise from the printer unplug it before taking following measures Switch off the printer and unplug the set from the mains After the disappearance of the smoke call your dealer to repair it TO UNPLUG ee Install the printer on the stable surface If the printer falls down it can be broken and you can hurt yourself PROHIBIT Do not let water or other foreign objects in the printer f this happened switch off and unplug the printer before calling your dealer PROHIBIT Rev 1 02 Keep the desiccant out of children s reach f not they may eat it PROHIBIT Use only approved accessories and do not try to disassemble repair or remodel it for yourself Call your dealer when you need these services Do not touch the blade of auto cutter DISASSEMBLING PROHIBITED Do not use the printer when it is out of order This can c
26. rming auto calibration Rev 1 02 25 6 Peripherals Connection SPP R400 This product can communicate with peripherals by using Bluetooth wireless LAN or external interface cable USB or serial cable 6 1 Bluetooth amp Wireless LAN Connection 6 2 Interface Cable Connection Rev 1 02 1 The printer can be connected to devices equipped with Bluetooth communication capacity PDAs PCs etc 2 Use the Bluetooth connection function supported by the device to connect to the printer 3 The printer can be connected to other stations such as PDAs and PCs supporting wireless LAN communication in Ad hoc mode and AP in Infrastructure mode NOTE Refer to the Bluetooth Wireless LAN Manual for detailed information on its connection You can check the bluetooth environment authentication encryption connection mode and the wireless LAN environment IP SSID authentication encryption via the self test page 1 Open the external interface connector protection cap in the direction of the arrow CD 2 Connect the external communication cable option 3 to the connector NOTE Only use USB or serial cable option provided by BIXOLON 3 Connect the interface cable to the USB port of the device PDAs PCs etc NOTE The interface cable that can be connected with the printer is available in both USB and Serial type Refer to the service manual for detailed interface cable specification
27. ry from the quad battery charger NOTE Battery charging status descriptions are as follows Lamp Charge Status Charge Time Red Lamp On Charging Green Lamp Blinking Over 80 Charged Green Lamp On Fully Charged Within four hours nea Replace CAUTION 1 If the red lamp of the charger blinks install the battery again 2 If the red lamp continues to blink despite several attempts 4 5 times to install the battery contact your local dealer 3 The charging time may vary depending on the type of the charger or ambient temperature Rev 1 02 15 SPP R400 3 3 Paper Installation 1 Press the Open button to open the paper cover 2 Insert the paper as shown in the image Remove any remaining core of a fully used paper roll 3 Take care to align the paper correctly 4 Pull the paper out as shown in the image and close the paper cover 5 Tear off any excess paper in the direction of the side of the printer Rev 1 02 16 SPP R400 3 4 Using Belt Strap 1 Insert the belt strap screw into the belt strap hole 2 Use a coin to tighten the belt strap screw as shown in the image 3 Undo the belt strap Velcro 4 Fasten the belt strap to a belt 5 Close the Velcro as shown in the image Rev 1 02 17 SPP R400 3 5 Using Case Protective Case Optional 1 Open its top cover 2 Insert your printer into the case as sho
28. s 26 SPP R400 7 Printer Cleaning If the interior of the printer is dusty print quality can decline In such a case follow the instructions below to clean the printer CAUTION Make sure to turn the printer power off prior to cleaning As the print head gets very hot during printing if intending to clean the print head turn the printer power off and wait approximately 10 minute before commencement When cleaning the print head take care not to touch the heated portion of the print head The print head is susceptible to damage from static electricity etc Take care not to allow the print head to become scratched and or damaged in any way Ss 1 Open the paper cover and remove any paper that may be present 2 Wipe the print head with a cleaning pen 3 Use a cloth moistened with an alcohol solution to clean the paper sensor are and remove any paper remnants and or dust 4 Insert paper into the printer 1 2 minutes after completing the cleaning process and close the printer cover Rev 1 02 27 SPP R400 8 Appendix 8 1 Specifications Item Description Printing Method Thermal printing Printing Speed 80 mm sec Resolution 203 DPI paper Easy paper loading Character Size Font A 12 x 24 Font B 9 x 17 Font C 9 x 24 Characters Font A 48 64 English 95 Expanded Gra
29. s this button 2 For information on the self test refer to 4 Self Test 3 For information on the dump of hexadecimals refer to Service Manual e Battery Status Lamp Blue or Red e BATT 1 If three blue lamps are lit the battery is fully charged 77 Cy SN 2 If two blue lamps are lit the battery is half charged E 72 S p 3 If one blue lamp is lit the battery is at the lowest charge level 4 If the red lamp is lit the battery must be charged or replaced Error Lamp Left sided 1 If the red lamp is lit the paper cover is open 2 If the red lamp is blinking either the paper has been fully used or ERR R the print head is overheated Fill with paper or turn the printer off for at least 10 minutes 3 If the red lamp continues to blink it may indicate a more serious problem with the product and thus an authorized service dealer should be consulted Bluetooth amp Wireless LAN Lamp Right sided 1 When using Bluetooth If the printer is ready for wireless communication with any M STATUS Bluetooth the green lamp as well as the battery status lamp is turned on 2 When using wireless LAN The right indicator shows the signal strength from wireless LAN The green lamp blinks for acceptable signal strength while the red lamp blinks for weak signal strength In power save mode only the Status lamp is lit NOTE The power saving mode is activated after the first communication with the default time
30. t ABCDEFGH JKLMNOPQRSTUV 0123456789 lt gt ABCDEFGHI JKLMNOPQRSTUV 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWX 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXY 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ 0123456789 lt gt ABCDEFGH JALMNOPQRSTUVWXYZ W 0123456789 lt gt ABCDEFGH JALMNOPQRSTUVWXYZ W 0123456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZL W 0123456789 0ABCDEFGH JKLMNOPQRSTUVWXYZI 123456789 lt gt ABCDEFGH JKLM orar P 23456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W _ 3456789 lt gt 7 JKLMNOPQRSTUMWXYZ W 456789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W _ 56789 lt gt ABCDEFGH JKLM o d _ abcd abcde _ abcdef _ abcdefg abcdefgh abcdef gh 6789 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W 789 0ABCDEFGHI Ae U 89 0ABCDEFGHI JKLMNOPQRSTUVWXYZ W 9 lt gt ABCDEFGH JKLMNOPQRSTUVWXYZ W lt gt 70 JKLMNOPQRSTUVWXYZ W PC437 1 amp 1 0 aes 1 Pt E0660 0jp c xX Ptfaiou aac sitiAAExeA
31. tery pack There is a risk of fire and or explosion How to dispose of battery packs may vary depending on countries or regions Dispose of it in the correct method Recommendation for Charging Do not charge your battery pack in a way not mentioned in the instruction manual Doing so may result in fire or explosion FCC compliance Information This device complies with part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Information to the user NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the
32. wn in the figure on the left 3 Close the Velcro 4 Attach the printer to the belt using the clip on the back of the case 5 Open the paper discharger when using the printer as shown in the figure Note The clip of the case can be rotated in two steps of 30 for each step up to 60 Rev 1 02 18 SPP R400 3 6 Using Shoulder Strap Optional 1 Connect the clips of the shoulder strap to the printer as shown in the figure on the left 2 Connect the clips of the case as shown in the figure on the left Rev 1 02 19 SPP R400 3 7 Adjusting Paper Guide 1 In order to use 105mm paper hold the upper edge of the paper guide and adjust the paper guide for both sides in the direc tion of the arrow shown in the picture 112mm 105mm 2 In order to use 112mm paper hold the upper edge of the paper guide and adjust the paper guide for both sides in the direction of the arrow shown in the picture Rev 1 02 20 SPP R400 3 8 Using Control Panel Power Button zm This button is used to turn the printer on off 4 1 To turn the printer on press and hold the button for approximately two seconds when the printer is off 2 To turn the printer off press and hold the button for approximately two seconds when the printer is on Paper Feed Button This button is used to feed paper manually take the self set and dump hexadecimals 1 To feed paper manually pres
Download Pdf Manuals
Related Search