Video Borescope - Extech Instruments
Contents
1. BR250 EU EN v7 4 2 14 Description 1 AN DOF WN 11 12 13 14 15 16 17 Signal output Power Indicator Power On Off Dimmer Flexible tube Camera head and LED s OK Up arrow video or jpg Menu Down arrow Power On Off Power Indicator USB Socket Video output SD card socket Power supply socket Reset Signal input BR200 BR250 EU EN v7 4 2 14 Installation Install the batteries into the instrument body charge the monitor battery connect the camera and flexible tube to the body and insert the micro SD card Install any accessory as needed Battery Installation Connect Monitor Power The monitor has a rechargeable battery Plug in the AC adaptor and connect the cable to the DCS5V socket on the monitor The power indicator will light in red or the battery capacity icon on LCD of monitor will blink indicating that it is charging and will turn off after a full charge Connect the camera and flexible tube Connect the camera tube to the instrument body ensure that the keyed ends are properly aligned Once aligned tighten the knurled knob to hold the connection firmly in place Warning Permanent damage to the flex tube and loss of operation will occur if the flex tube is subjected to narrow radius or sharp angle bends Inserting the micro SD card Insert card with arrow pointing toward slot Gently apply pressure until car2. is filled to capacity the SD card icon changes to F No video will be recorded if the SD card is not inserted in the slot Delete a Single Video Or Photo 1 2 3 0001 0003 PLAYBACK In the Real Time Monitoring mode press to display a list of dated 2009 05 14 playback folders 000 08 31 Use the Y Akeys to select the desired folder 2009 06 10 Press OK to open the selected folder and view a list of photo or video files Files are listed by time followed by VID for photos or VID for videos 0001 0004 13 00 24 VID Use the VW Akeys to select a file 13 00 24 VID i 13 00 24 VID Press and HOLD the button the display will show DELETE 13 00 24 VID CURRENT FILE Use the arrow keys to select YES or NO Press OK to accept selection Press twice to exit the Delete screen Delete a File Folder To delete a folder use the same instructions for deleting a single video or photo The only additional concern is that if a folder is not empty it cannot be deleted Delete all of the files in a folder before deleting the folder If the user attempts to delete a folder that is not empty the following message will appear FOLDER NOT EMPTY Video Display on a PC Several methods are available to playback or to copy video files on a PC When connected the files will become available as new drives on the PC 1 2 3 SD card adaptor Insert the SD card into the SD adaptor and th
3. BR200 530g BR250 450g BR200 17mm 0 67 BR250 9mm 0 36 10 C 50 C 14 F 122 F 3 5 TFT LCD 320 R G B x 240 PAL NTSC 2468MHz CH 4 5VDC 500mA 3 hours 2 hours 0 9 1 3VP P 750 lt 85dBm 100 x 70 x 25 mm 140g 10 C 50 C 14 F 122 F 15 85 RH This device complies with part 15 of the FCC rules BR250 200 FCC ID TW5GB8802 GB8803 Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Copyright 2014 FLIR Systems Inc All rights reserved including the right of reproduction in whole or in part in any form 1SO 9001 Certified www extech com 10 BR200 BR250 EU EN v7 4 2 14
4. EXTECH User Guide INSTRUMENTS Video Borescope Models BR200 and BR250 Introduction Congratulations on your purchase of this Extech BR200 17mm camera head or BR250 9mm camera head Video Borescope This instrument was designed for use as a remote inspection device It can be used to peer into tight spots and then supply real time video and images that can be recorded Typical applications include HVAC inspection automotive inspection cable routing and automotive boat aircraft inspection This meter is shipped fully tested and with proper use will provide years of reliable service Features 3 5 TFT LCD palm LCD monitor with high resolution The image head and the cable are water resistant when the unit is fully assembled the monitor and the camera are not water resistant Wireless and hard wired functionality The monitor records video and images Micro SD card memory 16G max size Please use Class 6 or higher TF Flash memory card Safety Supplied Equipment Do not expose instrument to moisture Shut off the instrument when not in use Remove the batteries when cleaning the instrument Replace all batteries at the same time 1 Camera 2 LCD Monitor 3 Monitor Adaptor p 4 Adaptor cable lt Bd 5 Accessory Magnet Hook Mirror to 4 5 6 6 Magnetic mount 7 Flex cable and camera head 10 8 4 AA Batteries CS Note Micro SD card and adaptor not shown 7 8 2 BR200
5. camera 2 Press and hold the monitor power switch for at least 2 seconds and the power indicator will illuminate green and a Welcome screen will appear 3 The real time image will then appear on the display LCD monitor Note If the picture does not properly syncronize or has poor color check that the Video System Settings are set to NTSC not to PAL This should fix the condition Op 4 Use the up arrow to select video or photo mode Turn the ON OFF dial to adjust the LED light intensity as desired 6 The tube can be easily maneuvered into position The tube can be bent into the shape of the area to be examined 7 Use the supplied accessories to help retrieve small items LCD Reset If the BR200 BR250 LCD Monitor will not power ON or if it powers OFF during use follow the steps below to perform a Power Reset 1 Un dock the LCD module from the BR200 BR250 pistol grip base unit 2 Connect the AC adapter to the LCD module and to the appropriate AC power source 3 Locate the Power Reset port on the reverse side of the LCD module labeled Reset 4 Using a non metallic object momentarily press the Power Reset button for a period of 2 to 5 seconds and then release a Leaving the AC adapter connected to the LCD module attempt to power the unit ON 6 Ifthe unit powers ON allow it to fully re charge up to 2 hours before removing the AC adapter If the LCD unit does not power ON re
6. d locks into the spring loaded slot To remove from unit gently push the card inward and then release to eject it from the card slot Please use Class 6 or higher TF Flash memory card 4 BR200 BR250 EU EN v7 4 2 14 Installing the accessory tools BR200 The included accessories mirror hook and magnet all attach to the camera in the same manner Refer to the diagrams below Installing the accessory tools BR250 Hook the attachment into the hole in the head and then slide the rubber sleeve over the attachment shaft TET CE Attaching the Monitor to the instrument body Connect the USB Cable Use the USB cable to connect the monitor to a PC The USB online icon will appear on the PC Open My Computer on the PC and locate the Mobile Disk The Mobile disk can be used and accessed in the same manner as any external hard drive Video Output Insert the video cable into the VIDEO OUT socket on the monitor Insert the other end of the cable into the VIDEO IN jack of a TV or other monitor The LCD Monitor will output a high quality video image Installing the Magnetic bracket The magnetic bracket slides onto the rear of the monitor for convenient placement and viewing 5 BR200 BR250 EU EN v7 4 2 14 Operation Basic Operation 1 Turn the ON OFF dial switch to power the camera The power indicator will switch on The switch then acts as a dimmer for the two LEDs on the imager head of the
7. en insert the adaptor into the PC SD slot if available USB adaptor Insert the SD card into a USB adaptor and plug into a USB port USB cable Connect the USB cable from the camera to the PC 7 BR200 BR250 EU EN v7 4 2 14 Settings Mode Press and hold for two seconds to enter the Settings Mode Language Settings 1 OV BN 6 In Settings Mode use the arrow keys to select SYSTEM SETTING green icon Press OK to call up the SYSTEM icon list Use the arrow keys to highlight the Language icon globe Press OK and the Language icon list will appear flags Use the arrow keys to highlight the desired language Press OK to select the highlighted language and exit Video System Settings 1 OPN 6 In Settings Mode use the arrow keys to select SYSTEM SETTING green icon Press OK to call up the SYSTEM icon list Use the arrow keys to highlight the Video System icon yellow Press OK and the Video format selections will appear NTSC PAL Use the arrow keys to highlight NTSC Press OK to select the highlighted format and exit Format and Erase Media DOT GN In Settings Mode use the arrow keys to select SYSTEM SETTING green icon Press OK to call up the SYSTEM icon list Use the arrow keys to highlight the FORMAT icon blue Press OK and the FORMAT selection screen will appear YES NO Use the arrow keys to highlight the desired response Press OK to accept the selection and exit Restoring Factory Defa
8. peat steps 1 through 6 lf after two attempts to reset the LCD the unit still does not power ON contact Technical Support Taking a Picture In Photo _ mode press OK to take a picture The photo will automatically save to the SD card Recording a Video In Real Time Monitoring video mode press OK to begin recording refer to the following diagram for display icon definitions 1 3 2 Battery capacity _ Vs lt Function icon video photo j Recording in progress ZOOM level Current Date and Time B 7 A REC Time remaining SD card PY OG RGN es 5 2009 07 28 1 0x 7 1 12 31 1 00 00 6 6 BR200 BR250 EU EN v7 4 2 14 Viewing a Photo or Video 1 7 8 Note In the Real Time Monitoring mode press Cr display a list of dated playback folders 2009 05 14 Use the V Akeys to select the desired folder 2009 05 21 Press OK to open the selected folder and view a list of photo or 200306710 video files Files are listed by time followed by VID for photos or VID for videos Use the V Akeys to select a file Press OK to display the selected photo or video For video files Press OK to pause while playing Press again to resume A Fast Forwards the video Vv Rewinds the video 0001 0003 0001 0004 Press to stop video Press to return to menu Press again to exit Video automatically saves to file every 30 minutes When the SD card
9. s window 3 Use OK to tab through the fields 4 Use the arrow keys to change a field setting 5 Press the button to exit Battery Replacement You as the end user are legally bound EU Battery ordinance to return all used batteries disposal in the household garbage is prohibited You can hand over your used batteries accumulators at collection points in your community or wherever batteries accumulators are sold S35 Disposal Follow the valid legal stipulations in respect of the disposal of the device at the end of its lifecycle 9 BR200 BR250 EU EN v7 4 2 14 Specifications CAMERA Imaging Sensor Total Pixels NTSC Horizontal View Angle Transmission Frequency Focus point Minimum Illumination Modulation Type Bandwidth Power Supply Unobstructed Effective Range Waterproof Capacity Dimensions W D H Weight approx Camera head Diameter Operating Temperature MONITOR LCD Screen Type Effective Pixels Video System Transmission Frequency Exterior Supply Voltage Consumption Current Max Charge Time Work Time Video Output Level Receiving Sensitivity Dimensions W x D x H Weight Approx Operating Temperature Operating Humidity Max FCC Information CMOS BR200 712 x 486 BR250 640 x 480 BR200 50 degrees BR250 45 degrees 2468MHz BR200 20cm 8 BR250 10cm 4 0 Lux FM 18MHz 4 x AA batteries 10m IP67 imager head only 186 x 145 x 41 mm Exclude Flexible Tube
10. ult Settings 1 OT BION 6 In Settings Mode use the arrow keys to select SYSTEM SETTING green icon Press OK to call up the SYSTEM icon list Use the arrow keys to highlight the DEFAULT icon red Press OK and the DEFAULT selection screen will appear YES NO Use the arrow keys to highlight the desired response Press OK to accept the selection and exit View Version In Settings Mode use the arrow keys to select SYSTEM SETTING green icon Press OK to call up the SYSTEM icon list Use the arrow keys to highlight the VERSION icon green Press OK to view the version Press OK again to exit Frame Rate Setting 1 OV BOS In Settings Mode use the arrow keys to select RECORDER SETTING red icon Press OK to call up the RECORDER options Use the arrow keys to highlight the FPS frames per second icon Press OK to open the FPS parameter Use the arrows to select the frame rate 10 15 20 25 or 30 Press OK to confirm 8 BR200 BR250 EU EN v7 4 2 14 Time Stamp ON OFF Setting ti akon 6 In Settings Mode use the arrow keys to select RECORDER SETTING red icon Press OK to call up the RECORDER options Use the arrow keys to highlight the Time Stamp icon purple Press OK to open the parameter Use the arrows to select ON or OFF Press OK to confirm Date Time Setting 1 In Settings Mode use the arrow keys to select DATE TIME SETTING yellow icon 2 Press OK to call up Date and Time Setting
Download Pdf Manuals
Related Search